to: subject: delivery hold - safety recall 15s14 – … · 2016. 9. 14. · michael a. berardi...
TRANSCRIPT
Copyright 2015 Ford Motor Company
Michael A. Berardi Ford Motor Company Director P. O. Box 1904 Service Engineering Operations Dearborn, Michigan 48121 Ford Customer Service Division
July 16, 2015 TO: All U.S. Ford and Lincoln Dealers SUBJECT: DELIVERY HOLD - Safety Recall 15S14 – Supplement #3
Certain 2013-2015 Model Year Fusion and MKZ and 2015 Model Year Edge Vehicles Steering Gear Motor Bolt Corrosion
REF: Regional Program 15R01 – Supplement #1 Dated July 10, 2015
REASON FOR THIS SUPPLEMENT
Provide updated labor allowances and technical instructions.
AFFECTED VEHICLES
Vehicle Line Model Year Assembly Plant Build Dates
Fusion 2014-2015 Flat Rock Job #1 2014 through March 13, 2015
Fusion 2013-2015 Hermosillo Job #1 2013 through March 19, 2015
MKZ 2013-2015 Hermosillo Job #1 2013 through March 20, 2015
Edge 2015 Oakville February 26, 2015 through February 28, 2015
This recall applies to the affected vehicles originally sold in, or currently registered in the following states:
Connecticut Iowa Minnesota Ohio Wisconsin
Delaware Maine Missouri Pennsylvania
District of Columbia Maryland New Hampshire Rhode Island
Illinois Massachusetts New Jersey Vermont
Indiana Michigan New York West Virginia
Affected vehicles are identified in OASIS and FSA VIN List.
NOTE: Some sold vehicles were inadvertently activated in OASIS under 15S14 that should have been under 15R01. This was corrected May 31, 2015.
Copyright 2015 Ford Motor Company
REASON FOR THIS SAFETY RECALL
In some of the affected vehicles, when operated in high-corrosion environments associated with road salt use, one or more of the three steering gear motor bolts may fracture due to corrosion. If this occurs, it may result in a loss of power steering assist, increasing the risk of a crash. The mechanical linkage between the steering wheel and the road is maintained at all times. The steering system will default to manual steering mode, allowing the vehicle to be steered in a safe and controlled manner.
SERVICE ACTION
Before delivering any of the vehicles involved in this recall, dealers are to perform one of the following:
New in-stock Fusion and MKZ vehicles: Dealers will apply either Valugard Rust Inhibitor Aerosol VG-101A or Daubert NOX RUST® 7703-W to specific locations on the steering gear.
o This procedure should only be performed on new in-stock vehicles because these vehicles have not had the potential to accumulate corrosion damage in the steering gear motors with time in service.
o A very limited number of 2015 Edge vehicles (11) are affected by this recall. Ford is not aware of any new in-stock 2015 Edge vehicles currently in dealer inventory affected by this program.
All sold vehicles:
o Dealers are to remove the original steering gear motor bolts, install revised bolts, and apply sealant to specified areas of the steering gear.
o If any of the original steering gear motor bolts are broken, missing or break during removal, dealers will replace the steering gear assembly.
o This service must be performed on affected vehicles at no charge to the vehicle owner.
OWNER NOTIFICATION MAILING SCHEDULE
Owners of record will be notified via first-class mail the week of June 22, 2015, when it is expected that complete parts ordering and repair instructions will be available to support this safety recall.
PLEASE NOTE:
Federal law requires dealers to complete this recall service before a new vehicle is delivered to the buyer or lessee. Violation of this requirement by a dealer could result in a civil penalty of up to $7,000 per vehicle. Correct all vehicles in your new vehicle inventory before delivery.
New! ATTACHMENTS
Attachment I: Administrative Information Attachment II: Labor Allowances and Parts Ordering Information Attachment III: Technical Information Owner Notification Letter Recall Reimbursement Plan
QUESTIONS & ASSISTANCE
Special Service Support Center (Dealer Assistance Only) 1-800-325-5621
Sincerely,
Michael A. Berardi
Copyright 2015 Ford Motor Company
ATTACHMENT I Page 1 of 2
DELIVERY HOLD - Safety Recall 15S14 – Supplement #3 Certain 2013-2015 Model Year Fusion and MKZ and 2015 Model Year Edge Vehicles
Steering Gear Motor Bolt Corrosion
OASIS ACTIVATED?
Yes, OASIS will be activated on April 29, 2015.
FSA VIN LIST ACTIVATED?
Yes, FSA VIN list will be available through https://web.fsavinlists.dealerconnection.com April 29, 2015. Owner names and addresses will be available by July 8, 2015.
NOTE: Your FSA VIN list may contain owner names and addresses obtained from motor vehicle registration records. The use of such motor vehicle registration data for any purpose other than in connection with this recall is a violation of law in several states, provinces, and countries. Accordingly, you must limit the use of this listing to the follow-up necessary to complete this recall.
STOCK VEHICLES
Correct all affected units in your new vehicle inventory before delivery.
SOLD VEHICLES
Owners of affected vehicles will be directed to dealers for repairs.
Immediately contact any of your affected customers whose vehicles are not on your VIN list but are identified in OASIS. Give the customer a copy of the Owner Notification Letter (when available) and schedule a service date.
Correct other affected vehicles identified in OASIS which are brought to your dealership.
TITLE BRANDED / SALVAGED VEHICLES
Affected title branded and salvaged vehicles are eligible for this recall.
ADDITIONAL LABOR TIME AND/OR PARTS
Contact the Special Service Support Center (SSSC) if you have any of the following:
Damage that you believe was caused by the covered condition.
A condition that requires additional labor and/or parts to complete the repair.
Aftermarket equipment or non-Ford modifications to the vehicle which might prevent the repair of the covered condition.
Contact the SSSC prior to the repair. Please be prepared to provide your requested additional warranty part cost, estimated additional labor time, and dealer specific labor rate. Requests for approval after completion of the repair may not be granted. Ford Motor Company reserves the right to deny coverage for related damage in cases where the vehicle owner has not had this recall performed on a timely basis. Additional related damage parts are subject to random selection for return to the Ford Warranty Parts Analysis Center (WPAC).
Copyright 2015 Ford Motor Company
ATTACHMENT I Page 2 of 2
DELIVERY HOLD - Safety Recall 15S14 – Supplement #3 Certain 2013-2015 Model Year Fusion and MKZ and 2015 Model Year Edge Vehicles
Steering Gear Motor Bolt Corrosion
OWNER REFUNDS
This safety recall must still be performed, even if the owner has paid for a previous repair. Claiming a refund will not close the recall on the vehicle.
Ford Motor Company is offering a refund for owner-paid repairs covered by this recall if the repair was performed prior to the date indicated in the reimbursement plan, which is posted with this bulletin. Owners are directed to seek reimbursement through authorized dealers or, at their option, directly through Ford Motor Company at P.O. Box 6251, Dearborn, MI 48121-6251.
Dealers are also pre-approved to refund owner-paid emergency repairs that were performed away from an authorized servicing dealer after the end date specified in the reimbursement plan. Non-covered repairs, or those judged by Ford to be excessive, will not be reimbursed.
Refunds will only be provided for the cost associated with steering gear replacement caused by corroded steering gear motor bolts.
RENTAL VEHICLES
The use of rental vehicles is not approved for this program.
CLAIMS PREPARATION AND SUBMISSION
Enter claims using Direct Warranty Entry (DWE) or One Warranty Solution (OWS).
o DWE: Refer to ACESII manual for claims preparation and submission information.
o OWS: When entering claims in DMS software, select claim type 31: Field Service Action. The FSA number (15S14) is the sub code.
Refer to ACESII manual for claims preparation and submission information.
Additional labor and/or parts must be claimed as related damage on a repair line that is separate from the repair line on which the FSA is claimed. Additional labor and/or parts require prior approval from the Special Service Support Center.
Submit refunds on a separate repair line.
- Program Code: 15S14 - Misc. Expense: ADMIN
- Misc. Expense: REFUND - Misc. Expense: 0.2 Hrs.
Multiple refunds should be submitted on one repair line and the invoice details for each repair should be detailed in the comments section of the claim.
Provision for Locally Obtained Supplies: Valugard VG-101A Rust Inhibitor Aerosol or Daubert NOX RUST® 7703-W. Submit on the same line as the repair.
- Program Code: 15S14
- Misc. Expense: OTHER
- Misc. Expense: Claim up to $5.00
Copyright 2015 Ford Motor Company
ATTACHMENT II Page 1 of 2
DELIVERY HOLD - Safety Recall 15S14 – Supplement #3 Certain 2013-2015 Model Year Fusion and MKZ and 2015 Model Year Edge Vehicles
Steering Gear Motor Bolt Corrosion
New! LABOR ALLOWANCES
Description Labor Operation Labor Time
New unsold Fusion/MKZ - apply sealer to specific locations on steering gear
15S14B 0.9 Hours
Install three new steering gear motor bolts and apply sealer to specific locations on steering gear
15S14C Edge/Fusion/MKZ 1.0 Hrs
MKZ 3.7L TiVCT 1.7 Hrs
One of the three steering gear motor bolts broke attempting to remove - replace steering gear assembly (includes time to set toe)
15S14D
Edge/Fusion 3.7 Hrs
MKZ 4.3 Hrs
MKZ 3.7 TiVCT 4.8 Hrs
Vehicle arrives at dealer with steering gear motor bolt(s) broken - replace steering gear assembly (includes time to set toe)
15S14E
Edge/Fusion 3.5 Hrs
MKZ 4.2 Hrs
MKZ 3.7 TiVCT 4.7 Hrs
New! PARTS REQUIREMENTS / ORDERING INFORMATION
All vehicles
Part Number Description Quantity
W503298-S439 Steering Gear Motor Bolts (one package includes four bolts –
three bolts required per vehicle) 1
VG-101A Valugard Rust Inhibitor Aerosol (obtain from www.valugard.net) Claim as MISC OTHER 7703-W Daubert NOX RUST® (obtain from www.daubertchemical.com)
MKZ with 3.7L TiVCT Engine
Part Number Description Quantity
W520103-S442 Exhaust Nut (one package includes four nuts – 8 nuts required per vehicle)
2
7T4Z-9450-AA Exhaust Gasket – Exhaust Y-pipe to catalyst 1
BT4Z-9450-A Exhaust Gasket – Exhaust Y-pipe to muffler assembly 1
Copyright 2015 Ford Motor Company
ATTACHMENT II Page 2 of 2
DELIVERY HOLD - Safety Recall 15S14 – Supplement #3 Certain 2013-2015 Model Year Fusion and MKZ and 2015 Model Year Edge Vehicles
Steering Gear Motor Bolt Corrosion
New! PARTS REQUIREMENTS / ORDERING INFORMATION (continued)
The DOR/COR number for this recall is 50595.
NOTE: Either Valugard or Daubert brand products can be used.
For assistance obtaining Valugard products, contact Automotive International customer service at 800-543-7156 Monday – Friday 8:00AM to 5:00PM Eastern Time.
For assistance obtaining Daubert products, contact Daubert at 800-688-0459 Monday – Friday 8:00AM to 5:00PM Central Time.
Both Valugard and Daubert have rust preventative product available in bulk quantities (e.g. Quarts, 5-gallons, and larger). These products are applied using commercially available spray equipment compatible with cavity wax coatings. In addition, both Valugard and Daubert also have spray equipment available for application.
Valugard – Part Number VG-CRG
Daubert – Part Number 3300 HSDR Pressure Pot Kit
Questions regarding parts should be directed to the Special Service Support Center (1-800-325-5621) or E-mailed to: [email protected].
DEALER PRICE
For latest prices, refer to DOES II.
PARTS RETENTION AND RETURN
Follow the provisions of the Warranty and Policy Manual, Section 1 “WARRANTY PARTS RETENTION AND RETURN POLICIES.”
EXCESS STOCK RETURN
Excess stock returned for credit must have been purchased from Ford Customer Service Division in accordance with Policy Procedure Bulletin 4000.
ATTACHMENT III PAGE 1 OF 11
SAFETY RECALL 15S14-S3
CPR © 2015 FORD MOTOR COMPANYDEARBORN, MICHIGAN 481217/2015
CERTAIN 2013 THROuGH 2015 MOdEL YEAR FuSION ANd MKZ ANd 2015 MOdEL YEAR EdGE VEHICLES — STEERING GEAR MOTOR bOLT CORROSION
SERVICE PROCEduRE
Remove underbody Shields - Fusion and MKZ Vehicles
NOTE: For Edge vehicles, proceed to Page 2. 1. Remove the engine front undershield and the engine undershield. Please follow the Workshop Manual (WSM) procedures in Section 501-02.
2. Remove both underbody side shields. See Figure 1.
NOTE: Left side shown right side similar.
FIGuRE 1
1519A
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
x8
x4
x2
FIGuRE 2
1519B
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
UNDERBODY CROSSBRACE
x6
3. Remove the six nuts and the underbody crossbrace. See Figure 2.
ATTACHMENT III PAGE 2 OF 11
SAFETY RECALL 15S14-S3
CPR © 2015 FORD MOTOR COMPANYDEARBORN, MICHIGAN 481217/2015
Remove underbody Shields - Edge Vehicles
1. Remove the underbody shield. See Figure 3.
NOTE: One piece underbody shield shown two piece underbody shield similar.
FIGuRE 31519Y
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
E198343
x2
x11
FIGuRE 4
1519Z
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
E198347
x2
2. If equipped, remove the center underbody shield. See Figure 4.
3. If equipped, remove the steering gear motor heat shield. See Figure 5.
FIGuRE 5
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
x3
1519AA
ATTACHMENT III PAGE 3 OF 11
SAFETY RECALL 15S14-S3
CPR © 2015 FORD MOTOR COMPANYDEARBORN, MICHIGAN 481217/2015
FIGURE 7
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
x3
1519AA
MKZ Vehicles Equipped With 3.7L
1. Remove the exhaust y-pipe. Please follow the WSM procedures in Section 309-00B.
2. Remove the right hand (RH) roll restrictor bolt. See Figure 6.
3. With the help of an assistant using a pry bar between the subframe and roll restrictor bracket, position the engine forward to provide clearance. Remove the steering gear motor heat shield. See Figure 7.
NOTE: Edge steering gear motor heat shield shown MKZ similar.
1519II
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
ROLL RESTRICTOR BOLT
ROLL RESTRICTORBRACKET
SUBFRAME
FIGURE 6
ATTACHMENT III PAGE 4 OF 11
SAFETY RECALL 15S14-S3
CPR © 2015 FORD MOTOR COMPANYDEARBORN, MICHIGAN 481217/2015
New in-stock - Fusion and MKZ Vehicles
1. For new in-stock vehicles, proceed directly to "Apply Corrosion Protection" on Page 7. Application of corrosion protection is the only service required on new in-stock vehicles.
Steering Gear Motor Inspection - Sold Vehicles Only
1. Inspect the steering gear motor for signs of separation, broken or missing bolts. See Figure 8.
2. Are any of the bolts broken or missing, or is a gap present between the motor and motor housing?
Yes – replace the steering gear. Please follow the WSM procedures in Section 211-02. Proceed to "Apply Corrosion Protection" on Page 7. No – proceed to "Replace Steering Gear Motor Bolts".
Replace Steering Gear Motor bolts - Sold Vehicles Only
NOTE: This repair involves the replacement of the three steering gear motor to steering gear housing bolts. See Figures 9, 10, 11, 12 and 13. In-stock vehicles do not require installation of new bolts because they did not have time to accumulate corrosion.
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
OLD BOLT NEW BOLT
1519HH
FIGuRE 9
1519R
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
STEERINGGEAR MOTOR
FIGuRE 8
ATTACHMENT III PAGE 5 OF 11
SAFETY RECALL 15S14-S3
CPR © 2015 FORD MOTOR COMPANYDEARBORN, MICHIGAN 481217/2015
1519CC
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
FRONT OFVEHICLE
FIGuRE 10
1519GG
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
FRONT OFVEHICLE
NEW BOLT #1
NEW BOLT #2
FIGuRE 11
Important: The steering gear motor bolts must be removed and replaced one at a time to preserve belt tension. Failure to do so may result in belt damage and steering gear replacement may be required.
1. Working from the front of the subframe, first replace steering gear motor bolt one. Then replace bolt two. See Figures 10 and 11.
• Tighten to 22.5 Nm (17 lb-ft).
ATTACHMENT III PAGE 6 OF 11
SAFETY RECALL 15S14-S3
CPR © 2015 FORD MOTOR COMPANYDEARBORN, MICHIGAN 481217/2015
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
1519DD
FRONT OFVEHICLE
FIGuRE 12
2. Working from the rear of the subframe, replace steering gear motor bolt three, then proceed to "Apply Corrosion Protection" on Page 7. See Figures 12 and 13.
• Tighten to 22.5 Nm (17 lb-ft).
1519FF
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
NEW BOLT #3
FRONT OFVEHICLE
FIGuRE 13
ATTACHMENT III PAGE 7 OF 11
SAFETY RECALL 15S14-S3
CPR © 2015 FORD MOTOR COMPANYDEARBORN, MICHIGAN 481217/2015
Apply Corrosion Protection
NOTE: Valugard Rust Inhibitor Aerosol VG-101A or Daubert NOX RUST® 7703-W Corrosion Protection (sealant) must be applied to the eight steering gear bolt heads, threads, and the steering gear motor to gear housing mating seam. See Figures 14 and 15.
FIGuRE 14
1519BB
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
FRONT OFVEHICLE
FIGuRE 15
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
1519T
FRONT OFVEHICLE
FRONT OFVEHICLE
APPLICATION AREA
ATTACHMENT III PAGE 8 OF 11
SAFETY RECALL 15S14-S3
CPR © 2015 FORD MOTOR COMPANYDEARBORN, MICHIGAN 481217/2015
1. Remove the RH front wheel. Please follow the WSM procedures in Section 204-04A.
2. Working from inside the RH wheelwell, insert spray nozzle under motor and forward between motor and gear. Apply sealant to housing and gear motor seam, gear motor and housing bolts five and six heads, threads and thread holes. See Figures 16 and 17.
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
1519J
FRONT OF VEHICLE
STEERINGGEAR MOTOR
FIGuRE 17
1519U
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
LHRH
FIGuRE 16
ATTACHMENT III PAGE 9 OF 11
SAFETY RECALL 15S14-S3
CPR © 2015 FORD MOTOR COMPANYDEARBORN, MICHIGAN 481217/2015
3. Working from the rear of the subframe, insert nozzle between the steering gear and subframe underneath housing seam. Apply sealant to gear motor bolt three, steering gear to housing seam and housing bolts four and eight heads, threads and thread holes. See Figures 18 and 19.
1519V
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
RHLH
FIGuRE 18
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
FRONT OF VEHICLE
SPRAY SEALANT INTO OR ON:
- BENEATH WIRE GEAR MOTOR HARNESS
- BOLT HEADS
- TOP OF GEAR MOTOR TO HOUSING SEAM
GEAR MOTORHARNESS
1519N
FIGuRE 19
ATTACHMENT III PAGE 10 OF 11
SAFETY RECALL 15S14-S3
CPR © 2015 FORD MOTOR COMPANYDEARBORN, MICHIGAN 481217/2015
FIGuRE 21
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
FRONT OF VEHICLE
1519M
SPRAY SEALANT INTO OR ON:
- BOLT THREAD HOLES
- BOLT HEADS
- GEAR MOTOR TO HOUSING SEAM
NOTE: Be sure the sealant coats the top of the gear motor seam and the bolt thread holes.
4. Working from the front of the subframe, insert nozzle between steering gear and subframe housing seam. Apply sealant to gear motor bolts one and two, steering gear to housing seam, housing bolts five, six and seven heads, threads and thread holes. See Figures 20 and 21.
1519W
PLACE COPY HERE
PLACE COPY HERE
PLACE COPY HERE
STUD FORMISSING NUT
STUD FORMISSING NUT
STUD FORMISSING NUT
LHRH
FIGuRE 20
5. Install the RH front wheel. Please follow the WSM procedures in Section 204-04A.
ATTACHMENT III PAGE 11 OF 11
SAFETY RECALL 15S14-S3
CPR © 2015 FORD MOTOR COMPANYDEARBORN, MICHIGAN 481217/2015
MKZ Vehicles Equipped With 3.7L
1. With the help of an assistant using a pry bar between the subframe and roll restrictor bracket, position the engine forward to provide clearance. Install the steering gear motor heat shield. See Figure 7.
• Tighten to 8 Nm (71 lb-in).
2. Install the RH roll restrictor bolt. See Figure 6.
a. Clean the bolt threads using a suitable wire brush. b. Apply Motorcraft Threadlock 262/TA-26 to restrictor bolt.
• Tighten to 115 Nm (85 Lb-ft).
3. Install the exhaust y-pipe. Please follow the WSM procedures in Section 309-00B.
Install underbody Shields - Edge Vehicles
1. If equipped, install the steering gear motor heat shield. See Figure 5.
• Tighten to 8 Nm (71 lb-in).
2. If equipped, install the center underbody shield. See Figure 4.
3. Install the underbody shield. See Figure 3.
Install underbody Shields - Fusion and MKZ Vehicles
1. Install the underbody crossbrace and the six nuts. See Figure 2.
• Tighten to 45 Nm (33 lb-ft).
2. Install both underbody shields. See Figure 1.
• Tighten to 9 Nm (80 lb-in).
3. Install the engine front undershield and the engine undershield. Please follow the WSM procedures in Section 501-02.