tm swi-cp5 universal steering wheel control retention
TRANSCRIPT
SWI-CP5Universal Steering Wheel Control Retention Interface
TM
Steering Wheel Control Interface
Page 1
Introduction & Features
Features
The SWI-CP5 interface allows the retention of steering wheel controls (SWC), rear seat controls (RSC) and retained accessory power (RAP) whenever replacing a factory radio. Use of this interface also allows you to program two radio functions to each SWC button by using short press/long press dual command functionality. The SWI-CP5 works in vehicles with either data or analog SWC.
Interface & Wiring Overview
• Compatible in vehicles equipped with LAN, LIN, CAN, Class II, Analog or Serial Data SWC• Easily configurable using either a PC, smartphone, tablet or manually• Audible feedback for programming confirmation• Retains memory even if power is lost• Ability to assign two radio functions to one SWC button• Updatable via the Android Application, Apple Application, PC Application or USB flash drive.• Create and save custom vehicle configuration files for later use.• Highly visible tricolor LED to keep the user informed of the modules status.• Equipped with a manual learning function for compatibility with unlisted vehicles.
(-) Chassis Ground
(+) Constant 12v Input
White/Red
Dark Green
Pink
Blue
Yellow/Black
White/Black
Red
Red/White
Black
Yellow
(-) Analog SWC Input 3
(+) Dual Wire CAN Hi Input
HVAC Output
12v Serial Data Input
(-) Analog SWC Input 2
(+) Accessory 12v Input
(+) Accessory 12v Output
Blue/Yellow SWC Output - Kenwood/Newer JVC
Purple
White
Pink/Black
Light Green
Class II Data Input
(-) Analog SWC Input 1
(-) Dual Wire CAN Low Input
(+) 12v Analog SWC Input
SW CAN Input
3.5mm JackSWC Output - Alpine, JVC, Clarion, Pioneer, Sony, Boyo, Dual, Advent,
Lightning Audio or Visteon
1 DIP
DIP
ON
23
41
23
45
67
8O
N
Vehicle DipswitchesVehicle Dipswitches
USB Port
Radio Dipswitches
Programming Button
Status LED
SWI-CP5Universal Steering Wheel Control Retention Interface
Pacific Accessory Corporation
TM
Steering Wheel Control Interface
Alpine Clarion Fusion JVC Kenwood Other Pioneer SonyRadio Dipswitch Settings
Other ‐ Advent, BOYO, Dual, Lightning Audio, Visteon, Rockford Fosgate
App ModeWith this method, the CP5 can be connected to a smartphone, tablet or PC in which the application assigns the vehicle and SWC button functionality. The dipswitches on the side of the interface must all be set to down which is the default position. When using this method, it is not required to manually program the SWC buttons.
1. Connect the CP5 to your device. If you are using a phone or tablet you must connect power to the CP5 and the supplied USBadapter to the CP5. If you are using a PC, neither power or the supplied adapter is required. PLEASE NOTE: When using aPC it may be necessary to update your Microsoft .NET Framework. If you require this update your PC will automatically notifyyou. If you do not get a notification then you do not require the update.
2. Launch the application or software and follow the on screen prompts.
Manual Configuration ModeWith this method, the CP5 uses a pre-determined dipswitch configuration to assign the vehicle and SWC button functionality. The dipswitches on the side of the interface must be manually set to the proper configuration by the user. These vehicle specific dipswitch settings can be found by downloading your device specific application. If you wish to re-assign button functions or use short press/long press dual command functionality, please follow the button re-assignment procedure outlined on page 5.
1. Launch the application or software and find your vehicle/radio combination.2. Set the vehicle dipswitches according to the application.3. Set the radio dipswitches according to the chart below.4. Wire up the interface according to the installation instructions in the application.
Manual Programming ModeWith this method the SWC values must be manually programmed into the CP5 by using either the app or the programming button. The vehicle dipswitches on the side of the interface must all be set to up. PLEASE NOTE: This mode is only compatible in vehicles with both analog SWC and a discrete 12v Accessory wire. Vehicles with CAN-Bus buttons cannot be manually programmed.
1. Launch the application and find the installation instructions for your vehicle.2. Set the radio dipswitches according to the chart below.3. Wire up the interface according to the installation instructions in the application.4. Connect the CP5 to the vehicle5. You can now either connect the CP5 to a device and use the app to program the SWC values or follow the programming
instructions on the next page.
Configuring/Programming
InstallationWe recommend that all wiring connections be soldered to ensure a sturdy and reliable connection.
SWI-CP5Universal Steering Wheel Control Retention Interface
TM
Steering Wheel Control Interface
Page 2
Radio Alpine JVC Kenwood Clarion Other* Sony Pioneer Fusion1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -3 Mute Mute Mute Mute Mute Mute Mute Mute4 Preset + Source Source Source Preset + Preset + Preset + Source5 Preset - Track + Play Search + Preset - Preset - Preset - Track +6 Source Track - Track + Search - Source Source Source Track -7 Track + Band/Disc + Track - Band Track + Track + Track + Audio8 Track - Preset/Disc - Disc/FM + Send/End Track - Track - Track - Power9 Power Select Disc/AM - Send Band Band Band
10 Enter/Play Attenuation Answer EndReject Call/Source
(Bluetooth equipped radios only)
Phone Menu
11 Band/Program Phone Receive Voice Dial Answer/End Call Answer Call12 Receive Phone Reject On Hook End Call13 End Voice Dial Off Hook Voice Activation
14 Power Mute (Multimedia units only)
*Other = Advent, Boyo, Dual, Lightning Audio, Rockford Fosgate, & Visteon
PLEASE NOTE: This section only applies to button programming in manual programming mode. If you are using the CP5 in manual configuration mode (specific vehicle dipswitch settings) and wish to re-assign button functions, please follow the “SWC Button Re-assignment Procedure” on page 4.
Please read each of the following steps to familiarize yourself with the process before beginning. The interface must be programmed in the specific order shown in the chart below
1. Turn the key to the ignition position. The LED will illuminate red.2. Press and hold the programming button on the side of the interface until the LED illuminates green and you hear ascending
chimes. Release the programming button.3. Within 7 seconds, press the button that is to be learned on the steering wheel. At this point you have two options:
a. For short press functionality: Hold the button on the steering wheel until a single chime is heard. The LED willchange to red once the button is learned. Release the button.
b. For long press functionality: Continue to hold the button until a long chime is heard. The LED will flash betweenred and amber once the button is learned. Release the button.
4. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.5. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press
and release the program button on the side of the interface to skip that function. The LED will go off and you will hear twochimes when it is done successfully.
6. Once programming is completed, wait seven seconds. The LED will flash green 3 times and you will hear descendingchimes indicating the end of programming.
7. Test the interface for proper functionality. Whenever a SWC button is pressed the LED on the interface should blink green.
Manually Mapping the SWC Buttons
Radio Function Mapping Order
Configuring/Programming (cont)USB Flash DriveWith this method, the CP5 can be configured using a USB flash drive and the supplied USB adapter. This will assign both a vehicle and SWC button functionality. The dipswitches on the side of the interface must all be set to down which is the default position. When using this method, it is not required to manually program the SWC buttons.
1. Create and save a configuration file with your application. Follow the instructions in your specific application for this procedure.2. Place the configuration file on the root directory of a USB flash drive (formatted to FAT32, it is best that this file be the only
thing on the flash drive)3. Connect the flash drive to the supplied USB adapter then connect the supplied USB adapter to the SWI-CP54. Connect the main harness to the SWI-CP55. LED will flash green while updating. If the file on the flash drive is the same the green LED will only flash once.6. Interface will chime when configuration is complete
SWI-CP5Universal Steering Wheel Control Retention Interface
Pacific Accessory Corporation
TM
Steering Wheel Control Interface
Testing & Verification
1. Turn the ignition on. The red LED on the interface will turn on & the +12v accessory output wire will turn on.2. Verify that all SWC are functioning properly. The green LED will flash each time it sees a steering wheel button pressed.3. Turn off the vehicle & remove the key. In vehicles equipped with retained accessory power (RAP) the accessory output and
the red LED will remain active & keep the radio on for 10 minutes unless the driver side door is opened. In vehicles that do notsupport RAP the LED and accessory output will shut off when the key is switched or removed from the ignition.
PLEASE NOTE: This section only applies to button re-assignment within a configuration. If you are using the CP5 in manual programming mode (all vehicle dipswitches up) please refer to the “Manually Mapping the SWC Buttons” section on page 3
If you wish to re-assign the SWC functions or utilize short press long press dual command functionality you will need to follow the steps outlined in this section. Please read each of the following steps to familiarize yourself with the process before beginning. The interface must be programmed in the specific order shown in the chart below.
1. Turn the key to the ignition position. The LED will illuminate red.2. Press and hold the programming button on the side of the interface until the LED illuminates green and you hear ascending
chimes. Release the programming button.3. Within 7 seconds, press the button that is to be learned on the steering wheel. The LED will turn red when the steering
wheel button is pressed. At this point you have two options:a. For short press functionality: Release the button on the steering wheel. A single chime will be heard and the
LED will change back to green.b. For long press functionality: Continue to hold the button until the LED flashes between red and amber and a
long chime is heard. Release the button and the LED will change back to green.4. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.5. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press
and release the program button on the side of the interface to skip that function. The LED will go off and you will hear twochimes when it is done successfully.
6. Once programming is completed, wait seven seconds. The LED will flash green 3 times and you will hear descendingchimes indicating the end of programming.
7. Test the interface for proper functionality. Whenever a SWC button is pressed the LED on the interface should blink green.If any function does not work, repeat the programming steps.
The SWC can always be restored to default settings by pressing and releasing the program button on the side of the interface once and waiting 7 seconds for the descending chime and the LED to flash 4 times.
SWC Button Re-assignment Procedure
Radio Alpine JVC Kenwood Clarion Other* Sony Pioneer Fusion1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -3 Mute Mute Mute Mute Mute Mute Mute Mute4 Preset + Source Source Source Preset + Preset + Preset + Source5 Preset - Track + Play Search + Preset - Preset - Preset - Track +6 Source Track - Track + Search - Source Source Source Track -7 Track + Band/Disc + Track - Band Track + Track + Track + Audio8 Track - Preset/Disc - Disc/FM + Send/End Track - Track - Track - Power9 Power Select Disc/AM - Send Band Band Band
10 Enter/Play Attenuation Answer EndReject Call/Source
(Bluetooth equipped radios only)
Phone Menu
11 Band/Program Phone Receive Voice Dial Answer/End Call Answer Call12 Receive Phone Reject On Hook End Call13 End Voice Dial Off Hook Voice Activation
14 Power Mute (Multimedia units only)
*Other = Advent, Boyo, Dual, Lightning Audio, Rockford Fosgate, & Visteon
Optional Programming Order
SWI-CP5Universal Steering Wheel Control Retention Interface
TM
Steering Wheel Control Interface
Page 4
Troubleshooting and FAQ
Color During Normal Operation During Manual Programming Mode During Optional Programming
Solid Red Accessory onWaiting on short press button
releaseWaiting on short press button
releaseSolid Green N/A Waiting on button to be pressed Waiting on button to be pressed
Solid Amber Update required ‐ Please call tech support N/A N/A
Flashing Green Button is being pressed N/A N/A
Flashing Red/AmberError ‐ Dipswitch setting on vehicle switches set to unknown config
Long Press Button detected Long Press Button detected
Flashing Green/RedError ‐ Dipswitch setting on radio switches
set to unknown configN/A N/A
Flashing Green/Amber/Red
Error ‐ Button not pressed long enough or value of button is too close to rest value
N/A N/A
Chime During Normal Operation During Manual Programming Mode During Optional Programming
Ascending Chimes N/A Programming Start Programming StartDescending Chimes N/A Programming End Programming End
Short Chime N/A Short Press SWC Value Stored Short Press ReleaseLong Chime N/A Long Press SWC Value Stored Long Press Release
High PitchDouble Chime
N/A Function Skipped Function Skipped
Low Pitch Double Chime
Programming Error/Incorrect Dipswitch Setting
N/A N/A
LED Legend
Chime Legend
Product Updates (Firmware)
The SWI-CP5 can be updated with new firmware as it becomes available using the device specific application or a USB flash drive. If using the application to update, please follow the procedures outlined there to update your interface. If using a USB flash drive, follow the procedure below.
1. Place the firmware file(s) on the root directory of a USB flash drive (formatted to FAT32, it is best that this update be the only thing on theflash drive)
2. Connect the flash drive to the supplied USB adapter3. Disconnect the main harness from the SWI-CP54. Connect the supplied USB adapter (with the USB drive connected) to the SWI-CP55. Connect the main harness to the SWI-CP56. LED will flash green while updating.7. Interface will chime when update is complete
Q. Where can I find the wiring info to connect the SWI-CP5 to my vehicle?A. The wiring info can be found within our Android, Apple or PC application.Q. Where can I find info on setting the dipswitches on the side of the module?A. The dipswitch settings can be found within our Android, Apple or PC application.Q. The module’s LED is flashing a pattern and the module is emitting two low tones every few seconds.A. Please reference the LED and chime legend above for your specific case.Q. What all can I connect to the Red/White (Accessory Output) wire on the module?A. The interface’s accessory output (Red/White) is only rated at 1 Amp. If you require more current capacity an external relay must be used.Q. Is there a way to perform a master reset to the module?A. The interface can be reset, when not connected via USB, by pressing and holding the programming button on the side of the interface for
seven seconds until the LED turns amber and a familiar tone is heard.Q. I have connected all of the wires and set the dipswitches as instructed. I am having an issue where some or all of the buttons are not
functioning correctly or at all.A. Verify that all of the ground wires (Radio, CP5, and Steering wheel circuit) are connected at the same place. In some vehicles the factory
ground may not be a sufficient ground for all of these wires. In this case please make all ground connections to chassis ground.Q. I’m using the application and I don’t see my radio listed (Advent, Boyo, Dual, Lightning Audio, Rockford Fosgate or Visteon).A. When installing any of these brands you will need to select Pioneer as your radio.
ControlPRO Application UpdateTechnical Bulletin
ControlPRO Application Update
If you received the incorrect dipswitch settings when using the ControlPRO app, to configure your SWI-CP5 module, you could be using an outdated version of the application. Please make sure you are using the latest version of the application, to receive the correct configuration information.
Check the version of the app installed on your device;1- Open the app2- Select “Options” 3- Select “About” 4- Your app version will be displayed
PC Users:If you are using a Windows PC to configure your SWI-CP5, please ensure you are using the latest application version: 20140808
To update your PC application, follow these steps:1- Uninstall the existing ControlPRO app from your PC2- Download the app3- Double-click the file, select “Run”
to install the ControlPRO app.
Smartphone or tablet users:Smartphone and Tablet users (Android or Apple), downloading the app from the appropriate app store, will provide you with the latest version. If the app is already installed on your smartphone or tablet, you should be automatically updated, or prompted when there is a new version of the app available to download.
PC:Latest version: 20140808
Android:Latest version: 1.0.7 Available now in Google Play
Apple: Latest version: 1.0.4Available now in iTunes
If you experience problems with the SWI-CP5 interface, please contact our Technical Support team, by phone, or through the support tab in the application.
Harley Davidson(1998 and Newer with SQ+, SQ- and PTT Buttons)
SWITCHPOSITION
BROWN /WHITE
PINK /WHITE
VIOLET /BLACK
GRAY /WHITE
UPMODEDOWN
RADIO FUNCTION SWITCH
RIGHT HAND CONTROLS
ALL MODELSEXCEPT
FLHTP-FRG
BN/WGY/WPK/WV/BK
GY/GNGN/BEPK/WBN/BK
V/BK
GY/GNGN/BEPK/W
O/BK
BN/BK
BN/WGY/WPK/WV/BK
PINK/WHITEGREY/WHITEVIOLET/BLACKBROWN/WHITEORANGE/BLACKBROWN/BLACK
GREY/GREENGREEN/BLUE
123456789
101112
123456789
101112
123456789
101112
123456789
101112
123456789
1011121314151617181920212223
SWITCHPOSITION
PINK /WHITE
GREEN /BLUE
BROWN /BLACK
GRAY /GREEN
VOL +AUDIOVOL -
RADIO AUDIO CONTOL
LEFT HAND CONTROLS
ALL MODELSEXCEPT
FLHTP-FRG
CONNECT HANDLEARSIDE TO GROUND
CONNECTORAT RADIO
Connect to Channel 1 (White) of the Control Pro Module
Connect to Channel 2 (White/Black) of the Control Pro ModuleConnect to Channel 3 (White/Red) of the Control Pro Module
1. Connect a 1K Ohm and 560 Ohm resistor to the Pink/ White (Pin 3) wire.2. Connect the free end of the 560 Ohm resistor to chassis ground.3. Connect the free end of the 1K Ohm resistor and the Green/Blue (Pin 23) wire together and connect it to Channel 1
(White) of the Control Pro Module.4. Connect the Grey/White (Pin 4) and Grey/Green (Pin 22) wires together and connect it to Channel 2 (White/Black) of
the Control Pro Module.5. Connect the Violet/Black (Pin 5) and Brown/Black (Pin 8) wires together and connect it to Channel 3 (White/Red) of
the Control Pro Module.6. Connect the Brown/White (Pin 6) wire to chassis ground.7. Cut the Violet/Black wire after the junction and ground the side that continues to the left handle bar through a 150
Ohm resistor.8. Connect the Orange/Black (Pin 7) to Channel 1 of the Control Pro module.
[24A]
[27A]
[24B]
[22A][22B]
1K Ohm
s
560 Ohm
s
O/BK
V/BK
150 Ohm
s
SWITCHPOSITION
VIOLET /BLACK
GREY /GREEN
ORANGE /BLACK
BROWN /GREEN
SQ +PTTSQ -
3 Additional Buttons
Harley Davidson(1998 and Newer)
SWITCHPOSITION
BROWN /WHITE
PINK /WHITE
VIOLET /BLACK
GRAY /WHITE
UPMODEDOWN
RADIO FUNCTION SWITCH
RIGHT HAND CONTROLS
ALL MODELSEXCEPT
FLHTP-FRG
BN/WGY/WPK/WV/BK
GY/GNGN/BEPK/WBN/BK
GY/GNGN/BEPK/WBN/BK
BN/WGY/WPK/WV/BK
PINK/WHITEGREY/WHITEVIOLET/BLACKBROWN/WHITE
BROWN/BLACK
GREY/GREENGREEN/BLUE
123456789
101112
123456789
101112
123456789
101112
123456789
101112
123456789
1011121314151617181920212223
SWITCHPOSITION
PINK /WHITE
GREEN /BLUE
BROWN /BLACK
GRAY /GREEN
VOL +AUDIOVOL -
RADIO AUDIO CONTOL
LEFT HAND CONTROLS
ALL MODELSEXCEPT
FLHTP-FRG
CONNECT HANDLEARSIDE TO GROUND
CONNECTORAT RADIO
Connect to Channel 1 (White) of the Control Pro Module
Connect to Channel 2 (White/Black) of the Control Pro ModuleConnect to Channel 3 (White/Red) of the Control Pro Module
1. Connect a 1K Ohm and 560 Ohm resistor to the Pink/ White (Pin 3) wire.2. Connect the free end of the 560 Ohm resistor to chassis ground.3. Connect the free end of the 1K Ohm resistor and the Green/Blue (Pin 23) wire together and connect it to
Channel 1 (White) of the Control Pro Module.4. Connect the Grey/White (Pin 4) and Grey/Green (Pin 22) wires together and connect it to Channel 2
(White/Black) of the Control Pro Module.5. Connect the Violet/Black (Pin 5) and Brown/Black (Pin 8) wires together and connect it to Channel 3
(White/Red) of the Control Pro Module.6. Connect the Brown/White (Pin 6) wire to chassis ground.
[24A]
[27A]
[24B]
[22A][22B]
1K Ohm
s
560 Ohm
s
Installation Parts