Slide 1

Thermoplastic Thickness Measuring Device Equipment Procedure Flat Line Measuring Audible Cookies Transverse bars w/ Inverted Rib Thermo on FC-5Topics that will be covered

Step 1. Zero-out Gauges

Step 2. Remove base-plate

Battery Replacement1. Florida Method of Test for FIELD EVALUATION of TRAFFIC MARKING MATERIALS Designation: 5-541

Standard Specifications Section 711Developmental Specs. Sections 701 & 702Procedure References:

Measuring Flat Line

Center the gauge over the marking material in an area avoiding glass spheres and read the values of all three dial indicators.

By procedure, the staff will take three measurements with them being at the beginning, middle and end of each one mile section of line type. Then average of the three location measurements shall be used for acceptance of the one mile section of line type (FM 5-541).Ocala Baseline Road SR 35 North Bound South BoundDialsDialsLocation 1 2 3 AVG. 1 2 3 AVG. 80' North of Dogwood TRL Pass1st.180 .216 .109 0.167.134 .228 .142 0.1682nd.097 .156 .052 0.102.172 .218 .108 0.1663rd.136 .182 .093 0.137.123 .155 .143 0.1404th.130 .200 .040 0.123.118 .142 .146 0.135AVG.0.132AVG.0.152Front of J.E.T.S. (address number 6249)1st.049 .161 .102 0.104.169 .270 .113 0.1842nd.058 .150 .093 0.100.152 .252 .116 0.1733rd.069 .183 .118 0.123.139 .266 .106 0.170AVG.0.109AVG.0.17680' North of Juniper Road1stOutside Line.046 .150 .159 0.118.107 .151 .106 0.1212nd.071 .170 .107 0.116.079 .154 .085 0.1063rd.145 .188 .133 0.155.091 .137 .069 0.106AVG.0.130AVG.0.1111stInside Line.123 .172 .123 0.139.137 .138 .083 0.1192nd.084 .205 .120 0.136.151 .161 .114 0.1423rd.108 .188 .074 0.121.129 .123 .104 0.119AVG.0.132AVG.0.127Target Thickness = 0.10 to 0.150 inchMAX THICKNESS = 0.150 inchRED TEXT = OUT OF TOLERANCE (OVER OR UNDER)Overall Thickness0.126Overall Thickness0.141Measuring Audible Cookies

Problem:Cookies are too tall for device to measure.

Solution:Take a reading across the cookie in the same direction as the line

Then one right in front of or behind the cookie, add the two numbers together.

Transverse Bars w/ Inverted Rib

Apply base lines having a thickness of 0.079 to 0.120 inches, exclusive of the transverse audible bars, when measured above the pavement surface at the edge of the base line. The profiled baseline shall have a minimum height of 0.155 inches, when measured above the pavement surface at the edge of the inverted rib profile. The thickness in the bottom of the profile marking shall be 0.035 to 0.050 inches. The individual profiles shall be located transversely across the full width of the traffic stripe.

Device can be used to measure this type of line. Thermo on FC-5

Issue:Having trouble getting required thickness due to the road soaking up material.

Solution:Pay close attention to final thickness measurement.Issues:

Things to RememberApply markings only to dry surfaces and when the ambient air and surface temperature is at least 50 deg and rising for asphalt surfaces and 60 deg and rising for concrete surfaces. (Dev. Spec. 702-4.1) Before applying traffic stripes over portland cement concrete surface, apply a primer, sealer or surface preparation adhesive. (Dev. Spec. 702-4.1) Any Questions????Presented by: Jack R. Davis District 5 Construction Support Specialistjack.davis@dot.state.fl.us386-943-5463