tgm220 english manual

Digital Multi Broadcasting Receiver TGM220

Safety Instructions

How to Use This Manual

This manual provides complete instructions for installing and using thereceiver.The following symbols will serve as follows.

32 Safety Instructions

Safety Instructions

Be sure to read this User’s Manual before starting the operation of the receiver.The socket-outlet shall be installed near the equipment and shall be easily

accessible.Never open the cover. It is dangerous to touch the inside of the receiver due

to possible electric hazard.Take enough space around the receiver for proper ventilation and do not coverventilation hole with items as newspaper, clothes etc..Lethal voltages are present inside the unit. Always be unplugged the receiverbefore connecting or disconnecting anything.When the receiver is unused for a long time, please disconnect it from the main

power.Never expose the receiver to water, moisture and extreme cold or direct sunlight.Do not insert or drop small objects into the unit.Never operate the receiver near any heat source.It is advisable to unplug the unit from the mains, TV, and the satellite dish when a

thunderstorm is expected.The receiver shall not be exposed to dripping or splashing and that no objects

filled with liquids, such as vases, shall be placed on the unit.Do not use a damaged power cord that may cause a fire or an electric shock.Do not touch a power cord with wet hand. It may cause an electric shock.The installation of a hard disk is only allowed by skilled person or your local

dealer. Unskilled installation of a hard disk would be loss of warranty.Always unplug the unit from main outlet before cleaning the unit. Do not use

solvents of any kind to clean the unit, only use a soft-dry cloth.

Symbol Explanation

[MENU] (A capital in bracket) Represents a button on the remote controller.

TV mode (Bold character) Represents OSD menu item.

4.4 Menus 28TV mode 29Radio mode 29

root 30File mode USB storage

recorded moviesInformation stream info 31

aboutreboot now 32

Reboot restart enigmago to standbyset sleeptimerbouquet edit creat new bouquet TV/Radio/File 33

Add services to bouquet TV/Radio/File Edit bouquets

satellite installation & TP Edit Manual Transponder Scansystem settings Time settings Time zone configuration

Time correction Setup A/V Settings

OSD disc setupOSD Language

Parental LockExpert setup Communication setup

Ngrab streaming setupSoftware update internet update

manual updateRemote controlFactory resetLoad default settingsEnable dish network EPGInfobar timeout 5sec

Add onGames 56Timer 57

Safety Instructions 2

1. Before You Begin 6

1.1 Features 6

1.2 Accessories 7

2. Controls and Functions 8

2.1 Front Panel 8

2.2 Rear Panel 10

2.3 Remote Control Unit 12

3. Connections and Caution 17

4. Settings and Operations 18

4.1 Basic Information 18

4.2 Get started for the first time 18

4.3 The Info-Bar 26

Contents

Contents

Contents4 5

71.Before You Begin6 1.Before You Begin

1. Before You Begin

Fully MPEG-2 & DVB CompliantLinux Open Source; Standard Linux APIGetting Linux Applications252MHz IBM PowerPC Processor (350MIPS) 72 MB RAM (64MB + 8MB)10/100M Full Duplex Ethernet Interface1 Smart Card?SlotS/PDIF Interface; Optical Type Samsung Tuner QAMFirmware/ Software Upgrade: Through Serial (RS232C), Ethernet & InternetUnlimited TV/Radio Channel StorageVery Quick Channel Change Time; < 1 secondFull Automatic Service ScanSmart Electronic Program Guide(EPG)OSD, VBI?Teletext & Subtitle SupportedVariable Aspect Ratio (4:3,16:9, Letter Box)Multi-Language MenuProgrammable Event TimerParental ControlVideo Out: CVBS, S-Video, Component OutputUSB 2.0 HostTuner changeable (Satellite <=> Cable)

1.1 Features 1.2 Accessories

92. Controls and Functions8 2. Controls and Functions

2. Controls and Functions

POWERTurn the receiver on/standby.

CH +/-Control channel.

VOL +/-Control volume level.

2.1 Front Panel

1

2

3

4

5

DISPLAY (4-digit, 7-segment)The 4-digit display program number or some menu status. On standby mode, itwill display local time.

SMART CARD SLOTInsert the card smoothly putting bottom side of Smart Card in direction of ICdown.



SAT INConnect the cable. Power off the receiver first.

SAT OUTLoops out to other devices. Connect an analogue receiver here. Power off thereceiver to watch analogue program.

ETHERNETThe communication port through HTTP, FTP, NFS, Telnet and Samba to accessyour recorded movies or to upload channel lists. This is also used to update theOperation system and download various Linux applications patch cable.

S-VIDEOConnect Super Video.

2.2 Rear Panel

1

2

3

4

VIDEOComposite video output for connecting to a TV, AV monitor, etc.

AUDIO L, RConnect with an appropriate RCA/Cinch cable to your HiFi-Amplifier.

COMPONENT (Y, Pb, Pr) Digital Video Output for Y, Pb, Pr.

RS-232CConnect your PC via this connector using a NUL female to female RS232 cablewhen you wish to upgrade the system software by serial communication port.

DIGITAL AUDIOConnect with an appropriate optical cable to your HiFi-Amplifier or DSP. TheAC3 signal is also available at this socket, if the selected channel transmits DolbyDigital signals.

USBUSB 2.0 external HDD.

TVConnect TV by RF cable.

MAIN SWITCH Power on/off the receiver.

POWER CORD (AC IN)100~240V AC (Auto-selectable), 50~60Hz +/-5%. Make sure to check the powerspecification.

5

6

7

8

9

10

11

12

13



2.3 Remote Control UnitMUTETurn the sound on and off.

POWERTurns the receiver on/standby (Power off in viewing mode only). If you press thebutton for more than 3 seconds, the Reboot/Sleep Timer menu will appear.Please refer to “4.4 Menus- (5) Reboot” instruction for further information.

NUMERIC KEY (0-9)Controls the numerical operation and changes the Channel/Service number directly.

TVOpens Service List.

RADIOOpens Radio Service List.

TEXTOpens Teletext. If the Service List is opened, by pressing the [TEXT] button, theFile Mode menu will open. To return to the Service List, press the [TV] or[Radio] button.

EPGPress the [EPG] button once to show the EPG info. Press it twice to enter theEPG Style menu. Press the [OK] button to view further information.

MENUOpens the Main Menu in viewing mode. If the [MENU] button is pressed whenthe Service List is opened, the Service Menu will appear.

EXITReturns to the previous menu or abort/exit operations.

1

2

3

4

5

6

7

8

9

14 2. Controls and Functions



CHANNELChanges channel, moves the cursor of channels in Service List, and movesUp/Down on the menu.

VOL◀/▶

Controls volume level, moves the page Up/Down in Service List, and movesLeft/Right on the menu.

OKPress the [OK] button to open the Service List in viewing mode. Press [OK] toconfirm a selection/function or to enter a chosen OSD menu.

VOLUME +/-Controls audio volume level.

BOUQUET +/-Shows the favorite channels in the bouquets you created. Press (+) to go up or ( - ) to go down the list.

INFOPress the [INFO] button once to open the INFO-Bar. Press it twice to view theINFO-Bar details.

TV/SATSwitchs between terrestrial and satellite channels.

AUDIOShows the available audio tracks (Audio Languages).

COLORS BUTTONSThese buttons activate certain menu functions. Usage instructions are shown ineach OSD menu. They also control the PVR functions in PVR-Mode.R( ):REWIND ,G( ):PLAY , Y( ) : PAUSE, B( ): FF(FASTFORWARD

10

11

12

13

14

15

16

17

18

INDEX MARKProduces a bookmark (chapter) while watching a recorded program.

SEEK FF( )Jumps the index forward to a bookmark (chapter).

SEEK RW( )Jumps the index backward to a bookmark (chapter).

PRE( )Returns to the previous channel/service or move to the beginning of the ServiceList or the Play List.

PVRAvailable in network PVR function (Ngrab, etc.)

These buttons control the PVR functions in PVR MODE.

• [REWIND] buttonSpeed rewind option. Every time the button is pressed, the speed increases x8,x16, x32, x64 accordingly.

• [PLAY] buttonStarts playback or restarts play during trick play or pause.

• [F.F] (FAST FORWARD) buttonFast forward option. Every time the button is pressed, the speed is to be x8,x16, x32, x64 accordingly.

• [PAUSE] buttonPauses screen. Press the button again to restart playback.

19

20

21

22

23

3 . Connections

3 . Connections and Caution

Install the receiver in horizontal position.Do not put any heavy objects such as a TV on the receiver.Do not install the receiver in vibrating place, direct sunlight, humid place,

extreme temperatures, and under unventilated places.

17

(Fogure. Connections)

16 2. Controls and Functions


• [STOP] buttonQuits the file in playback or trick play.

• [REC] buttonRecords selected program.During the recording, a red dot blinks in the Info-Bar and the "REC" sign lit on thefront of the unit. It indicates the recording is in progress.

NEXT( )Advances to the next channel/service or move to the end of the Service List or thePlay List.

24

194. Settings and Operations18 4. Settings and Operations

4. Settings and Operations

4.1 Basic Information

4.2 Get started for the first time

You can see the TV System Wizard . Choose your TV system with[LEFT/RIGHT]Navigation button and press [GREEN] button or [OK] to save.

OSD Language menu will appear automatically. Use the [UP] or[DOWN]Navigation button to choose your language. Press the [OK] button toactivate. (OSD Language menu is in the Main Menu of (6) Setup ➞ (3) SystemSettings ➞ (5) OSD Language)

2

3

1

[Menu Information]Selectable lines are generally activated (highlighted).Non-activated lines cannot be selected.Most menus show summarized information at the bottom.

[Basic Button Control]When you have reached the required subject menu, press the [OK] button to enter

to your selected menu.Use the [UP/DOWN] navigation buttons to change TV programIn most menus, you can select menu items with Navigation buttons.When you want to return to the previous menu without saving the change, press

the [EXIT] button.

Satellite Tuner

If it is the first time using a receiver, you should set parameters for systemconfiguration. Perform setup procedure below, when you have finished the procedure, you can startwatching TV or listening radio.

Turn onour TV and receiver.

4. Settings and Operations 2120 4. Settings and Operations

Satellite Configuration is next. Navigate to the upper dropdown list and chooseyour appropriate satellite configuration and press the [OK] button. Choose yoursatellites the dish is adjusted to, and press the [GREEN] or [OK] button on saveto save configuration. This Configuration might differ from yours. (S a t e l l i t eConfiguration menu is in the Main Menu of (6) Setup ➞ (2) Service Searching➞ (1) Satellite Configuration).

Transponder Scan is next. The Automatic Transponder Scan is recommended.The Automatic Transponder Scan scans satellite one by one. Select the firstsatellite to scan and press the [OK] button.

6

7

Time Zone Setup will appear next. Press the [OK] button to open the dropdownlist. Use [UP] or [DOWN] Navigation buttons to search for your Time Zone.Press the [OK] button to select.

DiSEqC… will appear next. Choose the DiSEqC you have installed.

4

5


234. Settings and Operations22 4. Settings and Operations


8

Only Free for FTA(Free to Air) and no circpolariz is for all available services.

Press the [OK] button to proceed to the next satellite scan or finish scan.(Transponder Scan is in the Main Menu of (6) Setup ➞ (2) Service Searching ➞

(5) Automatic Transponder Scan).

Now you can enjoy TV or Radio programs.

1

2

3

Cable Tuner

If it is the first time using a receiver, you should set parameters for systemconfiguration. Perform setup procedure below. When you have finished theprocedure, you can start watching TV or listening radio.

Turn on your TV and receiver.

You can see the TV System Wizard . Choose your TV system with[LEFT/RIGHT]Navigation button and press [GREEN] button or [OK] to save.

OSD Language menu will appear automatically. Use the [UP] or [DOWN]Navigation button to choose your language. Press the [OK] button to activate. (OSDL a n g u a g e menu is in the Main Menu of (6) S e t u p ➞ (3) System Settings ➞ ( 5 )OSD Language)



Time Zone Setup will appear next. Press the [OK] button to open the dropdownlist. Use [UP] or [DOWN] Navigation buttons to search for your Time Zone.Press the [OK] button to select.

Transponder Scan.

4

5

The Automatic Transponder Scan is recommended. The A u t o m a t i cTransponder scans channels automatically.

Press the [OK] button to start scan.

Now you can enjoy TV or Radio programs.

6

7

8

4. Settings and Operations 27

Subservices

If green dot in the Info-Bar appears, program provides subservices.Press the [GREEN] button to enter the menu multiple services. Use the Navigation-Buttons [UP] and [DOWN] to choose a service. Enable quick zap:Press the [GREEN] button to enable the quick zap mode. You can now choose a multipleservice using the Navigation buttons [LEFT] or [RIGHT] without entering this menu.Press the [GREEN] button to bring up this menu and press the [GREEN] button again todeactivate the quick zap mode.Add to bouquet:Press the [YELLOW] button to add the selected service to a Bouquet of your choice.

26 4. Settings and Operations


Info-Bar

The Info-Bar appears and disappears by pressing the [OK] button once in watchingmode. The Info-Bar shows all necessary information about the selected Service.

EPG (Electronic Program Guide)

Press the EPG button once to display EPG info which you last saw the last and press ittwice to display EPG style menu. Press the [OK] button to view details.

4.3 The Info-Bar



TV mode

Returns from PVR mode to TV mode.

Radio mode

Returns from PVR mode to Radio mode.

Audio Track

If yellow dot in the Info-Bar appears, program is transmitting multiple Audio-Tracks.Use the [LEFT] or [RIGHT] Navigation button to choose the different Audio modes,Left-Mono, Stereo, Right-Mono. Use the [UP] or [DOWN] Navigation button to choose another Audio language.

In the main menu you can set system configuration and scan TV & radio channels.Press the [MENU] button.

4.4 Menus



Information

You can see Stream info and your receiver information.

File mode

When you enter File mode, last chosen movie(recorded file) will be played.Press [UP] or [DOWN] Navigation button to see the list.

Root ([RED] button) : All folders such as programs and movies.Movies ([GREEN] button) : Recorded programsPlaylist ([YELLOW] button) : Selected programs and movies, jump beginning/ end with </>button.B o u q u e t s ([BLUE] button) : Bouquets with redorded programs on S e r v i c e

menu.If you press [MENU] button on this menu, Service Menu will appear. Please

refer to 4.4 Menus - (6)Setup – Service Organizing for more details.



Setup

Service Organizing

Create new bouquet

The Bouquets are used to save your favorite services from the Service List in onesimple bouquet.You can either add a TV, Radio or a File Bouquet.

You can see details about the chosen service in Streaminfo menu. Use [RIGHT]button to open next page of Streaminfo and [LEFT] button to go back. Also you can check manufacturer’s model no. and other information such asprocessor, hard disk and current software version in About...menu.

Reboot

reboot : Restarts the system.restart enigmagoto standby : same as stand by mode as [POWER] button.set sleeptimer

Maximum duration of 240 minutes. Press the [GREEN] button to set sleep timer.



Add services on the bouquet.

Choose the channels you want under the satellite then press [OK] to save on yourbouquet.

Now choose your desired services by navigating to them and pressing the [OK]button to select. All selected services appear red. To unselect a service, just pressthe [OK] button on it again.To finish selection press the [EXIT] button.The System will guide you back to the Service Organizing.

Select among TV, Radio or File to create a bouquet in that.Enter a name of your choice with the [NUMERIC KEYS] on your Remote-Control.

Press the [YELLOW] button for lower or uppercase letters.Press the [BLUE] button for numeric or letters to come first.Press the [VOL +] button to insert a letter or space.Press the [VOL -] button to remove a letter or space.Press the [OK] button to save. The system will guide you back to S e r v i c e

O r g a n i z i n g. You can check created bouquet in B o u q u e t s file under E d i tbouquets menu.

Add services to Bouquet

Select Bouquet Type and then menu shows the System default Bouquets, andthe bouquet you have created.



The same functions can be applied inside a Bouquet. Press the [EXIT] buttonto exit.

Satellite Installation & TP Edit

Satellite Tuner

Satellite ConfigurationExplained in previous menu, “4.2 Get started for the first time”.

Satfind

Choose from the lower dropdown lists your preferred satellite and transponder.Adjust the dish towards the desired satellite until you have a high level of Signalstrength AGC and on the Signal quality SNR indicator. The BER should alwaysindicate a value of zero if the Satellite is locked and synced.

SNR: Signal to Noise Ratio. This Indicator shows the Quality of the Signal.AGC: Automatic Gain Control. This Indicator shows the Strength of the Signal.BER: Bit Error Rate. This Indicator shows the Errors Rate of the Signal.

Edit Bouquets

Rename the selected Bouquet Type by pressing the [YELLOW] button.Choose a Bouquet Type you wish to edit a Bouquet from and press the [OK] button.

If you go into Bouquet, you can edit.Press the [RED] button to delete a selected Bouquet.Press the [GREEN] button to highlight a B o u q u e t and direct it to another

place in the list. Press the [GREEN] button again to release.Press the [YELLOW] button to rename a selected Bouquet.Press the [BLUE] button to set a marker between two Bouquets. A marker is

used to place visual remarks. You can create as many markers as you want.



After saving the configuration, go to Motor Setup from the Service Searching.Refer to the Motors Manual for correct values degrees/second. If unsure, set acheck in front of “Use Motor Input Power” and enter the maximum current theMotor is using for turning to the Dish.Visit the Website http://www.heavens-above.com to learn your geographicallocation. Enter the values for Longitude and Latitude and press [GREEN] buttonto save.With DiSEqC motor, you need proceed to Automatic Multisat Scan.

Motor Setup

Before proceeding with the Motor Setup choose “many satellites viaDiSEqC Motor” in Satellite Configuration if you are setting up a Motor forthe first time.

All available satellites will be listed. Press the [GREEN] button to save yourconfiguration.



Network search: The NIT holds the Information about the Satellites and theTV/Radio programs.(NIT = Network Information Table)Extended network search: Set a check to scan the NIT from otherTranspondersSkip known Networks: Unchecking this, decreases the sat scan. The NIT willnot be used.Use BAT: Bouquet Tables of the Provider will be used, if available.(BAT = Bouquet Association Table)Press the [GREEN] button to save.

Automatic Transponder ScanExplained in previous menu, “4.2 Get started for the first time”.

Transponder Edit

This Menu keeps all known satellites in the box scans for. If you recognize amissing satellite, add or edit the satellite.

Pressing the [OK] button on the sat menu, enters the Satellite Edit Menu.Pressing the [OK] button on the add menu, adds a new frequency to theselected satellite.Pressing the [OK] button on the edit menu, edits the Transponder Values forthe selected satellite.Pressing the [OK] button on the remove menu, removes a transponderfrequency from the selected satellite.Pressing the [GREEN] button, adds a new satellite.Pressing the [RED] button, deletes a satellite.



Manual Transponder Scan

The Manual Transponder Scan is recommended for scanning a specificTransponder that has not been found during Automatic Transponder Scan.Press the [OK] button on the upper dropdown list and choose the appropriatesatellite, press the [OK] button again to select.Type in the correct Transponder values in its fields. Press the [GREEN] button tostart scan. The scan results will be shown in the next window.

Satellite Installation & TP Edit

Cable Tuner

Explained in previous menu, “4.2 Get started for the first time”.

Automatic Multisat Scan

The Automatic Multisat Scan is recommended for scanning all configuredsatellites at once.By pressing the [OK] button on each satellite a determined number of times, youset the scan method. First pressing : nothing, satellite will not be scanned /Second pressing : all services will be scanned / Third pressing : only free serviceswill be scanned / Fourth pressing : nothing, againPress the [GREEN] button to start scan. The scan results will be shown in thenext window.



Use either the Navigation-Buttons [LEFT] and [RIGHT] or [OK] button tochange or set the values.

Color Format: CVBS (FBAS), RGB (Red, Green, Blue separated), SVideo(Color- and Brightness signal separated) and YPbPr(Component signal e.g. for Projectors).Aspect Ratio: 4:3 letterbox (standard), (16:9 programs will be displayed on 4:3TV’s with black beams at top and bottom ), 4:3 panscan (16:9 programs will bezoomed to full high on 4:3 TV’s, parts of the picture on the left and right sidewill cut off), 16:9 (programs transmitted in 16:9 will be displayed automaticallyin 16:9, on 4:3 TV’s the picture will be reduced in height)TV System: PAL, PAL+PAL60, Multinorm and NTSC Select the Norm your

TV supports. We suggest to choose Multinorm.Disable WSS on 4:3: Set a check into the Checkbox to disable zooming onsome 16:9 TV’s during 4:3 transmissions.AC3 default output: If a program is transmitted with an AC3 Audio-Track (e.g.Dolby Digital), the receiver switches automatically to this Audio-Track. TheAC3 Signal will only be available at the optical socket.The receiver doesn’t have a built-in Dolby Digital Decoder, AC3 signals are notavailable on the analogue socket and therefore you need an external DolbyDigital Amplifier to adjust the Volume.Auto VCR switching : Activating this function (standard) switches the Video

signal from the VCR socket to the TV. Depending on the used VCR, switchingtakes affect by turning on the VCR or starting playback.Press the [GREEN] button to save.

System Setting

Time SettingExplained in previous menu, “4.2 Get started for the first time”.

A/V Setting



USB disc Setup

You can get external HDD information and can format the HDD.

OSD Settings

Use the Navigation buttons [LEFT] or [RIGHT] button to decrease or increasethe selected option.

Alpha : Sets how much the TV picture should be visible through the OSD.Brightness : Sets the Brightness of the OSD.Contrast : Sets the Contrast of the OSD.Show Mainmenu like Listbox : Check to enable a list box view of the OSD Main menu.


Parental Lock

Locks services of your choice under the Service list against access. Setup lock isused to lock the Menu (6) Setup against access.The Parental setup requires a four digit code of your choice called PIN forParental lock and Setup lock.

To enable Parental lock, set a check in front of “Parental lock”. The Button“change PIN” appears and press the [OK] button to enter a PIN of your choice.Re-enter the PIN.If you don’t want to see locked services inside the Service List, set a check infront of “Hide locked services”.To disable Parental lock, uncheck the checkbox from “Parental lock” and enterthe PIN to verify.Press the [OK] button to save.Follow same process for setup lock.

Loosing this PIN requires a “Flash Erase” of the Operation System toreset to factory default.



Change skin : Sets a new skin. A skin changes the appearance of the OSD. Navigate to a skin of your choice and press the [OK] button to activate. The receiver will ask you to restart the operation system to apply the new skin.

TuxText position : Sets the TuxText position. The clock or the Text pages maynot in the middle of the screen.Press the [RED] button to move the top left point of the rectangle.Press the [GREEN] button to move the bottom right point of the rectangle.Use the Navigation buttons [DOWN/RIGHT] for the top left rectangle and[UP/LEFT] for the bottom right rectangle to adjust. Press the [OK] button to exit.

Press [GREEN] button to save or [OK] on save menu.

OSD LanguageSelect your language here. Please refer to “4.2 Get started for the first time”.

If you don’t see any rectangle, then they are out of range. Pleaseadjust the rectangle into the middle of the screen.

TuxtText is Plugin(additional Software). You need to refer to yourlocal dealer to enjoy various Plugins for the receiver.


Expert Setup

Communication Setup

Sets up appropriate network environment. Go to Communication Setup.

IP: Enter the Host IP-Address. Netmask: Enter the Netmask to find a Host IP-Address in its Subnet. LAN: Connection to the home Network. Default is LAN. Nameserver: Enter the DNS-Server IP-Address to switch a Domain name to an IP-Address. Gateway: Enter the Router’s IP-Address Enable Network: Press the [OK] button to enable the Network (a check/tickwill appear in the checkbox). Default is disabled. Port 80: Enter a Port of your choice to configure the HTTP Port for thereceiver Web Interface. Default is Port 80.



Once you setup Parental lock, you can lock/unlock any item in Service List.Press MENU on Service List to enter service menu and then you can see newoption “lock”.

Go to the option “lock”/“unlock” and press the [OK] button to lock/unlock theselected service. Beside the selected service appears the Symbol for a lockedservice.If you want to view/unlock this service next time you select it, you will be askedfor the PIN. Enter the PIN to view/unlock this service. After unlocking the Service,the Symbol for a locked service will disappear.

NoteSet a check to DHCP and press the [OK] button to avoid duplication to assign an IP-Address which the receiver is using.

5352

Software Update

Follow the instructions on the screen pressing the <OK> button .



Ngrab Streaming Setup

Recording a movie via the Network to the PC. Ngrab Server Software needs tobe installed on the PC.

Srv IP: Enter the IP-Address which the Ngrab Server Software runs. Srv MAC: Please check the Ngrab Server Software should be started andconfigured before detecting the MAC-Address of the PC. Press the [BLUE]button to detect the MAX-Address. Srv Port: Enter the Server Port-Address which Ngrab Server Software is configured. TheMAC-Address is used for the WOL(Wake On LAN) function, which must besupported by the PC’s NIC (Network Interface Card). You can configure a PCto use full APM (Advanced Power Management). The PC will detect accessthrough the NIC and the Ngrab recording will start.




Remote Control

Customizing the remote control at your needs. Use the [LEFT] or [RIGHT]Navigation buttons to adjust the Repeat Rate and Delay.Navigate to Remote control Style to select another Style. Change the Value “NextChar Timeout” for your needs. Try this setting. Press the [GREEN] button or[OK] on save menu to save.

Factory reset

Factory reset will restore all your data.

Load Default Settings

Quick factory reset (Reset your data beside flash memory data )

Infobar timeout

Adjust infobar time out time




Timer

Recording a service at your required time. It works in Standby mode.

Go to Service List by [UP] or [DOWN] Navigation button or TV button. Select aservice you want to program into the Timer. Watch this service for few seconds untilthe red EPG dot in the Info-Bar appears. Be noted not every service provides EPGInformation. Press the [RED] button. Choose an event and press the [GREEN] buttonto add it to the Timer. And then the Timer Edit window will appear.

Repeated Timer : Set a check to enable this Event to record for few days or thewhole week.You can change the starting and ending time for this event by navigating to itsdesired fields. Type new time with the NUMERIC Keys.

NoteSome services do not provide EPG infomation.

Add on

Add skins and others

Games

You can enjoy simple game by connections to the network, more games areavailable. Contact your local dealer for further information.



Switch - the Timer switches to this event.Ngrab - the Timer records to a Ngrab PC.Press the [GREEN] button to apply. The Event will be marked as a Timer eventin the Service List. Press the [EXIT] button to exit the Service List. To check aset Timer event, enter this menu to see Timer List.

Thank you for choosing ITGATE!

This manual can be changed without prior notice.

tgm220 english manual

Documents