tg 138 - locking ladder pulls - dormaproducts.dorma.com/content/download/38822/424672/926953...tg...

Installation instructions:

Back-to-back and single-sided locking ladder pulls

TG 138 - LOCKING LADDER PULLS

—

TG 138 - LOCKING LADDER PULLS—

DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800-523-8483 E-mail: [email protected]

926953 04/16 Reamstown, PA 17567 Fax: 800-274-9724 Subject to change without notice

2

Operator overallSpecifications General information

Mounting

Maintenance 3

Glass pulls

Glass door: Back-to-back locking ladder pull 4-8

Disassemble the back-to-back locking

ladder pull4

Reassemble the back-to-back locking ladder

pull6

Install the cylinder 7

Glass door: Single-sided top locking ladder pull 9-10

Assemble the single-sided top locking

ladder pull9

Install the cylinder 10

Wood door or 3/4" glass door applications

Replace the locking mechanism 11

Adjusting the locking pin 12

Preparing floor for dust proof strike 13




3

Specifications

Important safety-related information for the mounting and use of DORMA hardware.(Follow these instructions in addition to the mounting and operating instructions in order to avoid damage of product and damage to person or property.)

General information1. DORMA requires use of tempered glass or tempered

laminated glass.

2. DORMA hardware is not suitable for application in

rooms where chemicals (e.g. chlorine) are used as indoor

swimming pools, saunas or salt-water pools.

3. Never move sliding panels faster than walking speed

and always stop the door manually before it reaches end

position.

4. Do not swing doors with excessive force. Install limiting

stop to prevent door from opening too far.

Mounting1. Only properly qualified and specially trained staff is

authorized to mount DORMA hardware.

2. Never use glass with conchoidal fractures and/or

damaged edges.

3. Due to crushing hazards and possible injury caused

by breakage of glass during mounting, corresponding

protective clothing (especially gloves and protective

goggles) is required.

4. Clean clamping area with safe alcohol-based standard

commercial cleaning agent before mounting the glass

hardware.

5. Never clamp metal glass fitting hardware directly to glass

surface.

6. Never use clamping roller carriers on self-cleaning

coatings.

7. When adjusting glass elements, always stick to the

required clearance for the respective hardware. Adjust

clearance so glass does not come in contact with any

hard surfaces such as glass, metal or concrete.

8. Do not use excessive force when installing the glass

(avoid over tightening screws).

9. Ensure there is a minimum door clearance of 1/2". If not,

adjust door height accordingly prior to installation.

Maintenance Check glass hardware at regular intervals for proper

positioning and smooth operation and correct

adjustment. High traffic door systems require inspection

by properly qualified staff (specialized companies or

installation firms). Immediately replace damaged glass

elements (no glass flaking and/or conchoidal fractures)!

Only use suitable cleaning and care products to clean

the surfaces.




4

1.1 Lay the ladder pulls on a flat surface and disassemble.

Glass door: Back-to-back locking ladder pull

Set screw

Inside pullOutside pull

Set screw

Set screw

Disassemble the back to back locking ladder pull

1

1.2 Separate the pulls by loosening the set screws in each

post of the inside pull.




5

2.2 Unthread the following parts from the other posts:

threaded anchor

black plastic washers (qty: 2 per post)

spacer

threaded stud

Locking

shaft

Locking

anchor

Threaded

studSpacer

Threaded

anchor

Black plastic

washer

Glass door: Back-to-back locking ladder pull - continued

2.1 Unthread the locking anchor from the locking shaft

(which stays together in the post).

Outside pull

2




6

Re-assemble the back-to-back locking ladder pull

Self adhesive

washer

Black

plastic

washer

Self

adhesive

washer

Outside pull

Threaded

stud

Spacer

3.1 Reinstall the black plastic washers into the outside post.

NOTE: Be sure to use the appropriately sized locking mechanism dependent upon the thickness and type of door being used.

3.2 Secure the self-adhesive washers to the posts of the

outside pull.

3


3.3 Rethread the following parts into the posts of the outside

pull:

threaded stud

spacer




7

Install the cylinder:

4.1 Measure and cut the cylinder tailpiece to the desired

length as seen in the figure above.

4.2 Install the cylinder housing into the outside pull.

NOTE: Be sure the tailpiece engages with the locking mechanism.

Inside pullOutside pull

Cylinder

screws

Cylinder

housing

Cylinder

tailpiece

X

2-3/16 - 2-5/16"(55-60mm)

2-5/8"- X"(67-Xmm)

4.3 Measure and cut the two cylinder screws [2.63"-X"

(67-Xmm)] to the appropriate length as seen in the

figure above. Secure them into the back of the cylinder

housing.


4




8

Inside pull

Security

plug

Set

screws

Outside pull

ENSURE THERE IS A MINIMUM DOOR CLEARANCE OF 1/2". IF NOT, ADJUST DOOR HEIGHT ACCORDINGLY.

5.1 Place the outside pull through the door.

NOTE: BE SURE TO SUPPORT THE PULL IN THE DOOR WITH YOUR HAND.

5.2 Secure the self-adhesive washers for the inside pull onto

the glass door.

5.3 Be sure the clear plastic washer is still on the locking

anchor, then thread the following part onto locking shaft:

locking anchor

5.4 To secure the remaining posts, thread the following parts

onto the threaded stud:

black plastic washer

threaded anchor

5.5 Slide the inside pull onto the anchors and locking

mechanism.

NOTE: BE SURE THE INDEXING PIN ON THE LOCKING SHAFT IS IN THE DOWN POSITION.

5.6 Tighten with the set screw on each post of the inside

pull, make sure the pull is fully functioning, and add the

security plugs. NOTE: The plugs are permanent!

5

side l

Self-adhesive

washers

Black

plastic

washer

Threaded

anchor

Threaded

stud

Clear

plastic

washer

Locking

anchor

Locking

shaft

Indexing

pin


Self-adhesive

washer




9

Glass door: Single-sided top locking ladder pull

Assemble the single-sided top locking ladder pull

6.1 Lay the ladder pull on a flat surface.

6.2 Thread the following parts into each other:

single-sided trim rose

clear plastic washers

threaded stud

spacer

6.3 Feed the stud, spacer and rose assemblies through the

glass door.

6.4 To secure the post, thread the following parts onto the

threaded stud:

clear plastic washer

black pastic washer

threaded anchor

NOTE: THE TAPERED SIDE OF THE ANCHOR SHOULD FACE THE INSIDE PULL.

6.5 Slide the inside pull onto the anchors.

6.6 Tighten the set screw on each post of the inside pull and

add the security plugs. NOTE: The plugs are permanent!

Clear plastic

washers

Clear plastic

washers

Single-sided

trim rose

SpacerThreaded

stud

Black

plastic

washer

Threaded

anchor

6

Security

plug

Set

screws




10

Cylinder

tailpiece

Cylinder

housing

2-1/4"(58mm)

Cylinder

Cylinder

ring

Thumb turn

housing

Set screw

Locking

anchor

Set

screw

Set

screw

Security

plug

Security

plug

Locking

anchor

Install the cylinder: NOTE: If a single-sided top locking thumb turn is being installed, skip to step 2.6.

7

7.1 Measure and cut the cylinder tailpiece to the desired

length as seen in the figure above.

7.2 Measure and cut the two cylinder screws [9/16" (15mm)].

7.3 Place the cylinder through the cylinder ring.

7.4 Secure the cylinder alignment guide to the back of the

cylinder using the two 9/16" (15mm) screws.

7.5 Insert the cylinder and guide into the top of the pull.

NOTE: Be sure the guide lines up with the hole inside the pull.

NOTE: Be sure the cylinder tailpiece engages with the locking mechanism.

7.6 Tighten the set screw in the post to secure the cylinder.

7.7 Slide the pull onto the threaded anchors.

7.8 Tighten with the set screw on each post of the pull, make

sure the pull is fully functioning, and add the security

plugs. NOTE: The plugs are permanent!

9/16"(15mm)

Cylinder

alignment

guide

Cylinder

screws

Cylinder

screw

Glass door: Single-sided top locking ladder pull - continued




11

Replace the locking mechanism

8

8.1 Remove the screw from the back of the lock housing.

8.2 Remove the lock housing (includes locking shaft and

locking anchor).

8.3 Unthread the locking anchor from the locking shaft.

8.4 Remove the clamp ring from the back of the locking

shaft. Remove the locking shaft from the lock housing.

Wood door or 3/4" glass door applications

8.5 Replace with proper size locking shaft and locking

anchor.

8.6 Replace the shaft into the lock housing. Be sure the

spacer washer is not removed.

8.7 Secure the clamp ring.

8.8 Replace the lock housing into the locking post.

8.9 Replace the screw into the back of the housing.

Screw

Lock

housing

Locking

shaft

Locking

anchor

Clamp

ring

Screw Locking

post

Spacer

washer




12

Adjusting the locking pin

Locking pin

Inside pull

1

1.1 Once the pull has been secured to the door and is

properly functioning, adjust the height of the locking pin.

1.2 Partially insert the T-handle tool into the outer housing of

the locking pin.

1.3 Turn counter-clockwise to align with the inner hole of the

locking pin housing.

1.4 Slide the T-handle tool through the locking pin.

1.5 To extend the pin: Turn clockwise.

To retract the pin: Turn counter-clockwise.

+ -

-

+

Locking pin




13

Preparing floor for dust proof strike

1.1 Once the pull has been secured to the door, is properly

functioning, and the door is fully closed, place the

template on the floor underneath the inside pull.

1.2 With the locking pin extended, line the template up with

the pin.

1.3 Using an 3/4" (18mm) diameter drill bit, drill 1-5/8"

(40mm) into the floor.

1.4 Clean the hole of debris.

1.5 Insert dust proof strike into the hole.

1.6 Be sure the strike functions properly.

Strike template

ø3/4"

(ø18)

Image template NOT TO SCALE

Dust proof

strike

Dust proof

strike

Inside pull

oof

1

92

695

3

04

/2016

, S

ubje

ct

to c

hange w

ithout

notice

DORMA USA, INC.

DORMA DRIVE, DRAWER AC

REAMSTOWN, PA 17567

TOLL-FREE: 800-523-8483

FAX: 800-274-9724

E-MAIL: [email protected]

WWW.DORMA.COM

tg 138 - locking ladder pulls - dormaproducts.dorma.com/content/download/38822/424672/926953...tg...

Documents