testking cisco 640-816
TRANSCRIPT
BeITCert
ified.c
om
QUESTION NO: 1
To allow or prevent load balancing to network 172.16.3.0/24, which of the following commands
could be used in R2? (Choose two.)
A. R2(config-if)#clock rate
B. R2(config-if)#bandwidth
C. R2(config-if)#ip ospf cost
D. R2(config-if)#ip ospf priority
E. R2(config-router)#distance ospf
Answer: B,C
QUESTION NO: 2
After the network has converged, what type of messaging, if any, occurs between R3 and R4?
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 2
BeITCert
ified.c
om
A. No messages are exchanged
B. Hellos are sent every 10 seconds.
C. The full database from each router is sent every 30 seconds.
D. The routing table from each router is sent every 60 seconds.
Answer: B
QUESTION NO: 3
OSPF is configured using default classful addressing. With all routers and interfaces operational,
how many networks will be in the routing table of R1 that are indicated to be learned by OSPF?
A. 2
B. 3
C. 4
D. 5
E. 6
F. 7
Answer: C
QUESTION NO: 4
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 3
BeITCert
ified.c
om
R1 is configured with the default configuration of OSPF. From the following list of IP addresses
configured on R1, which address will the OSPF process select as the router ID?
A. 192.168.0.1
B. 172.16.1.1
C. 172.16.2.1
D. 172.16.2.225
Answer: A
QUESTION NO: 5 DRAG DROP
Riverside Towing is redesigning the network that connects its three locations. The administrator
gave the networking team 192 168.45 0 to use for addressing the entire network. After subnetting
the address, the team is ready to assign the addresses. The administrator plans to configure ip
subnet-zero and use RIP v2 as the routing protocol. As a member of the networking team, you
must address the network and at the same time conserve unused addresses for future growth.
With those goals in mind, drag the host addresses on the left to the correct router interface. One of
the routers is partially configured. Move your mouse over a router to view its configuration. Not all
of the host addresses on the left are necessary.
Answer:
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 4
BeITCert
ified.c
om
Explanation:
Cars Fa0/0 IP = 192.168.45.249/26
Trucks S0/1 IP = 192.168.45.165/30
Trucks Fa0/0 IP = 192.168.45.197/28
Vans Fa0/0 IP = 192.168.45.108/25
QUESTION NO: 6
Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.)
A. Global addresses start with 2000::/3.
B. Link-local addresses start with FE00::/12.
C. Link-local addresses start with FF00::/10.
D. There is only one loopback address and itis :: 1.
E. If a global address is assigned to an interface, then that is the only allowable address for the
interface.
Answer: A,D
QUESTION NO: 7
Refer to the exhibit. Given the partial configuration shown in the exhibit, why do internal
workstations on the 192.168.1.0 network fail to access the Internet?
A. A NAT pool has not been defined.
B. The wrong interface is overloaded.
C. NAT has not been applied to the inside and outside interfaces.
D. The access list has not been applied to the proper interface to allow traffic out of the internal
network.
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 5
BeITCert
ified.c
om
Answer: C
QUESTION NO: 8
Refer to the exhibit. Hosts in network 192.168.2.0 are unable to reach hosts in network
192.168.3.0. Based on the output from RouterA, what are two possible reasons for the failure?
(Choose two.)
A. Interface S0/0 on RouterB is administratively down.
B. Interface S0/0 on RouterA is configured with an incorrect subnet mask.
C. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU.
D. The IP address that is configured on S0/0 of RouterB is not in the correct subnet.
E. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that
is configured on S0/0 of RouterA.
F. The cable that is connected to S0/0 on RouterA is faulty.
Answer: C,E
Explanation:
Based on the information provided in the exhibit, we know that Serial0/0 is up, line protocol is
down, under normal circumstances there are three states:
1. serial0/0 up, line protocol is up The interface is up and the line protocol is up
2. serial0/0 down, line protocol is down The interface is down and there is something wrong with
the physical layer.
3. serial0/0 up, line protocol is down The interface is up, but the encapsulation format is not
matching ,clock rate issues
QUESTION NO: 9
A network administrator is explaining VTP configuration to a new technician. What should the
network administrator tell the new technician about VTP configuration? (Choose three.)
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 6
BeITCert
ified.c
om
A. A switch in the VTP client modecannot update its local VLAN database.
B. A trunk link must be configured between the switches to forward VTP updates.
C. A switch in the VTP server mode can update a switch in the VTP transparent mode.
D. A switch in the VTP transparent mode will forward updates that it receives to other switches.
E. A switch in the VTP server mode only updates switches in the VTP client mode that have a
higher VTP revision number.
F. A switch in the VTP server mode will update switches in the VTP client mode regardless of the
configured VTP domain membership.
Answer: A,B,D
QUESTION NO: 10
Refer to the exhibit. What statement is true of the configuration for this network?
A. The configuration that is shown provides inadequate outside address space for translation of
the number of inside addresses that are supported.
B. Because of the addressing on interface FastEthernet0/1, the Serial0/0 interface address will not
support the NAT configuration as shown
C. The number 1 referred to in the ip nat inside source command references access-list number 1.
D. ExternalRouter must be configured with static routes to networks 172.16.1.0/24 and
172.16.2.0/24.
Answer: C
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 7
BeITCert
ified.c
om
QUESTION NO: 11
Refer to the exhibit. Which mask is correct to use for the WAN link between the routers that will
provide connectivity while wasting the least amount of addresses?
A. /23
B. /24
C. /25
D. /30
Answer: D
QUESTION NO: 12
Refer to the exhibit. What can be determined about the interfaces of the Main_Campus router from
the output shown?
A. The LAN interfaces are configured on different subnets.
B. Interface FastEthernet 0/0 is configured as a trunk.
C. The Layer 2 protocol of interface Serial 0/1 is NOT operational.
D. The router is a modular router with five FastEthernet interfaces.
E. Interface FastEthernet 0/0 is administratively deactivated.
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 8
BeITCert
ified.c
om
Answer: B
QUESTION NO: 13
What are two characteristics of Frame Relay point-to-point subinterfaces? (Choose two.)
A. They create split-horizon issues.
B. They require a unique subnet within a routing domain.
C. They emulate leased lines.
D. They are ideal for full-mesh topologies.
E. They require the use of NBMA options when using OSPF.
Answer: B,C
QUESTION NO: 14
Refer to the exhibit. Which switch provides the spanning-tree designated port role for the network
segment that services the printers?
A. Switch1
B. Switch2
C. Switch3
D. Switch4
Answer: C
Explanation:
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 9
BeITCert
ified.c
om
Printers are connected by hubs. Decide the switch that provides the spanning-tree designated port
role between Switch3 and Switch4. They have the same priority 32768. Compare their MAC
addresses. Switch3 with a smaller MAC address will provide a designated port for printers.
Designated port A designated port is one that has been determined as having the best
(lowest) cost. A designated port will be marked as a forwarding port.
QUESTION NO: 15
A new switch is being added to the River Campus LAN. You will work to complete this process by
first configuring the building_210 switch with an IP address and default gateway. For the switch
host address, you should use the last available IP address on the management subnet. In
addition, the switch needs to be configured to be in the same VTP domain as the building_100
switch and also needs to be configured as a VTP client. Assume that the IP configuration and VTP
configuration on building_100 are complete and correct.
The configuration of the router is not accessible for this exercise. You must accomplish the
following tasks:
Determine and configure the IP host address of the new switch.
Determine and configure the default gateway of the new switch.
Determine and configure the correct VTP domain name for the new switch.
Configure the new switch as a VTP client.
A. PENDING - Please send us your suggestions for this question.
Answer: A
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 10
BeITCert
ified.c
om
QUESTION NO: 16 DRAG DROP
Drag each feature of the left to the appropriate routing protocol on the right.
Answer:
Explanation:
RIP Version 1
Sends frequent updates
Less complex configuration
Susceptible to routing loops
Exchanges full routing table in updates
OSPF
Faster convergence
Uses only event-triggered updates
Same topology information held by all routers
Requires more memory and processing power
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 11
BeITCert
ified.c
om
QUESTION NO: 17
What is the advantage of using a multipoint interface instead of point-to-point subinterfaces when
configuring a Frame Relay hub in a hub-and-spoke topology?
A. It avoids split-horizon issues with distance vector routing protocols.
B. IP addresses can be conserved if VLSM is not being used for subnetting.
C. A multipoint interface offers greater security compared to point-to-point subinterface
configurations.
D. The multiple IP network addresses required for a multipoint interface provide greater
addressing flexibility over point-to-point configurations.
Answer: B
Explanation:
Frame Relay supports two types of interfaces: point-to-point and multipoint. The one you choose
determines whether you need to use the configuration commands that ensure IP address to data-
link connection identifier (DLCI) mappings. After configuring the PVC itself, you must tell the router
which PVC to use in order to reach a specific destination.
Let's look at these options:
1. Point-to-point subinterface - With point-to-point subinterfaces, each pair of routers has
its own subnet. If you put the PVC on a point-to-point subinterface, the router assumes that there
is only one point-to-point PVC configured on the subinterface. Therefore, any IP packets with a
destination IP address in the same subnet are forwarded on this VC.
This is the simplest way to configure the mapping and is therefore the recommended method. Use
the frame-relay interface-dlci command to assign a DLCI to a specified Frame Relay subinterface.
2. Multipoint networks - Multipoint networks have three or more routers in the same subnet. If you
put the PVC in a point-to-multipoint subinterface or in the main interface (which is multipoint by
default), you need to either configure a static mapping or enable inverse Address Resolution
Protocol (ARP) for dynamic mapping.
QUESTION NO: 18
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 12
BeITCert
ified.c
om
Refer to the exhibit. Given the output for this command, if the router ID has not been manually set,
what router ID will OSPF use for this router?
A. 10.1.1.2
B. 10.154.154.1
C. 172.16.5.1
D. 192.168.5.3
Answer: C
QUESTION NO: 19
An access list has been designed to prevent Telnet traffic from the Graphics Department from
reaching the HR server attached to the Eastfield router but allow Telnet traffic to other
destinations. Given the following access list:
access-list 101 deny tcp any any eq 23 permit ip any any
On which router, interface, and in what direction should the access list be placed to most efficiently
implement this list? (Choose three.)
A. Westfield
B. Eastfield
C. e0
D. s0
E. in
F. out
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 13
BeITCert
ified.c
om
Answer: B,C,F
QUESTION NO: 20
Which two of these statements regarding RSTP are correct? (Choose two.)
A. RSTP cannot operate with PVST+.
B. RSTP defines new port roles.
C. RSTP defines no new port states.
D. RSTP is a proprietary implementation of IEEE 802.1 D STP.
E. RSTP is compatible with the original IEEE 802.1 D STP.
Answer: B,E
Explanation:
When network topology changes, rapid spanning tree protocol (IEEE802.1W, referred to as RSTP)
will speed up significantly the time to re-calculate spanning tree. RSTP not only defines the role of
other ports: alternative port and backup port, but also defines status of 3 ports: discarding status,
learning status, forwarding status.
RSTP is designed to be compatible and interoperable with the STP. However, the advantages of
the fast re-convergence, introduced by the RSTP are lost when it interoperate with STP bridges.
In order to ensure compatibility with STP bridges, each RSTP bridge listens on its ports for
configuration messages having the STP format. When a port receives such configuration message
it starts behaving as a standard 802.1d STP bridge port. Other ports continue to behave according
the RSTP.
QUESTION NO: 21
Refer to the exhibit. How should Switch1 and Switch2 be connected in order to allow full
communication between all of the hosts?
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 14
BeITCert
ified.c
om
A. Exhibit A
B. Exhibit B
C. Exhibit C
D. Exhibit D
E. Exhibit E
F. Exhibit F
Answer: F
QUESTION NO: 22
A router is running three routing processes: RIP, OSPF, and EIGRP, each configured with default
characteristics. Each process learns a route to the same remote network. If there are no static
routes to the destination and none of the routes were redistributed, which route will be placed in
the IP routing table?
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 15
BeITCert
ified.c
om
A. the route learned through EIGRP
B. the route learned through OSPF
C. the route learned through RIP
D. the route with the lowest metric
E. all three routes with the router load balancing
Answer: A
QUESTION NO: 23
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 16
BeITCert
ified.c
om
A static map to the LA-GROUP location is required. Which command should be used to create this
map?
A. frame-relay map ip 172.30.0.3 21 broadcast
B. frame-relay map ip 172.30.0.3 888 broadcast
C. frame-relay map ip 172.30.0.3 866 broadcast
D. frame-relay map ip 172.30.0.3 792 broadcast
Answer: D
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 17
BeITCert
ified.c
om
QUESTION NO: 24
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 18
BeITCert
ified.c
om
What destination Layer 2 address will be used in the frame header containing a packet for host
172.30.0.4?
A. 21
B. 833
C. 866
D. 792
Answer: D
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 19
BeITCert
ified.c
om
QUESTION NO: 25
Which command reveals the last method used to powercycle a router?
A. show reload
B. show boot
C. show running-config
D. show version
Answer: D
QUESTION NO: 26
Workstation A has been assigned an IP address of 192.0.2.24/28. Workstation B has been
assigned an IP address of 192.0.2.100/28. The two workstations are connected with a straight-
through cable. Attempts to ping between the hosts are unsuccessful. What two things can be done
to allow communications between the hosts? (Choose two.)
A. Replace the straight-through cable with a crossover cable.
B. Change the subnet mask of the hosts to/25.
C. Change the subnet mask of the hosts to /26.
D. Change the address of Workstation A to 192.0.2.15.
E. Change the address of Workstation B to 192.0.2.111.
Answer: A,B
QUESTION NO: 27 DRAG DROP
Drag each description on the left to the appropriate term on the right. Not all descriptions are used.
Answer:
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 20
BeITCert
ified.c
om
Explanation:
Holddown timer - prevents a router from improperly reinstating a route from a regular routing table
Split horizon - prevents information about a route from being sent in the direction from which the
route was learned
Defining a maximum - prevents invalid updates from looping the internetwork indefinitely
Route poisoning - causes a routing protocol to advertise an infinite metric for a failed route
Triggered update - decreases convergence time by immediately sending route information in
response to a topology change
QUESTION NO: 28
Which statement about IPv6 is true?
A. Addresses are not hierarchical and are assigned at random.
B. Only one IPv6 address can exist on a given interface.
C. There are 2.7 billion addresses available.
D. Broadcasts have been eliminated and replaced with multicasts.
Answer: D
Explanation:
This question is to check the concept of IPv6.
IPv4 supports three address types: unicast, multicast and broadcast.
In IPv6, broadcasts have been eliminated and replaced with multicasts. At the same time, IPv6
introduces another address type - anycast.
QUESTION NO: 29
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 21
BeITCert
ified.c
omRefer to the exhibit. The network is converged. After link-state advertisements are received from
Router_A, what information will Router_E contain in its routing table for the subnets 208.149.23.64
and 208.149.23.96?
A. 208.149.23.64(110/13] via 190.173.23.10,00:00:07, FastEthemet0/0
208.149.23.96(110/13] via 190.173.23.10,00:00:16, FastEthemet0/0
B. 208.149.23.64(110/1] via 190.172.23.10,00:00:07, Serial1/0
208.149.23.96(110/3] via 190.173.23.10,00:00:16, FastEthemetO/0
C. 208.149.23.64(110/13] via 190.173.23.10,00:00:07, Serial1/0
208.149.23.96(110/13] via 190.173.23.10,00:00:16, Serial1/0
208.149.23.96(110/13] via 190.173.23.10,00:00:16, FastEthemetO/0
D. 208.149.23.64(110/3] via 190.172.23.10,00:00:07, Serial1/0
208.149.23.96(110/3] via 190.173.23.10,00:00:16, Serial1/0
Answer: A
QUESTION NO: 30
Refer to the exhibit. Which two statements about the configuration of the switch interface are
correct? (Choose two.)
A. The switchport belongs only to VLAN 2.
B. By default, all switch ports are members of VLAN 1005.
C. Interface fa0/0 will be in both VLAN 1 (by default) and VLAN 2.
D. The exhibit shows interface fa0/0 to be dynamically mapped to VLAN 2.
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 22
BeITCert
ified.c
om
E. A network host can be connected to this interface.
Answer: A,E
Explanation:
On a Cisco switch, ports are assigned to a single VLAN. These ports are referred to as access
ports and provide a connection for end users or node devices, such as a router or server. By
default all devices are assigned to VLAN 1, known as the default VLAN . After creating a VLAN,
you can manually assign a port to that VLAN and it will be able to communicate only with or
through other devices in the VLAN. In this case, the port has been manually assigned to VLAN 2,
not the default value of VLAN 1.
QUESTION NO: 31
You are a network technician for CP. You enter the following line into the router:
R1(config)# access-list 106 deny tcp 192.168.254.0 0.0.0.255 any eq www
What is the effect of this configuration?
A. Web pages from the Internet cannot be accessed by hosts in the 192.168.254.0 LAN.
B. The change has no effect on the packets being filtered.
C. No hosts in the 192.168.254.0 LAN except 192.168.254.7 can access web pages from the
Internet.
D. All traffic from the 192.168.254.0 LAN to the Internet is permitted.
Answer: B
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 23
BeITCert
ified.c
om
Explanation:
Traffic that comes into the router is compared to ACL entries based on the order that the entries
occur in the router. New statements are added to the end of the list. The router continues to look
until it has a match. If no matches are found when the router reaches the end of the list, the traffic
is denied. For this reason, you should have the frequently hit entries at the top of the list. There is
an "implied deny" for traffic that is not permitted. A single-entry ACL with only one "deny" entry has
the effect of denying all traffic. You must have at least one "permit" statement in an ACL or all
traffic is blocked. In this example, since the statement will be added to the end of the access list,
and since there is already an entry that permits all IP traffic, the www traffic will be allowed, all
traffic will never reach this access list entry.
QUESTION NO: 32
You are a network administrator. The following graphic shows the topology and configuration
information of the network. You have configured the router to enable communication between the
VLANs. You are required to configure switch port fa0/1 to establish a link with router R1 using the
IEEE standard protocol, which IOS commands should be used? (Choose three.)
A. SW1(config)# interface fastethernet 0/1
B. SW1(config-if)# switchport trunk encapsulation dot1q
C. SW1(config-if)# switchport mode access
D. SW1(config-if)# switchport mode trunk
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 24
BeITCert
ified.c
om
Answer: A,B,D
Explanation:
.
QUESTION NO: 33
A network administrator wants to ensure that only the server can connect to port Fa0/1 on a
Catalyst switch. The server is plugged into the switch Fa0/1 port and the network administrator is
about to bring the server online. What can the administrator do to ensure that only the MAC
address of the server is allowed by switch port Fa0/1? (Choose two.)
A. Configure an access list on the switch to deny server traffic from entering any port other than
Fa0/1.
B. Configure port security on Fa0/1 to reject traffic with a source MAC address other than that of
the server.
C. Configure port Fa0/1 to accept connections only from the static IP address of the server.
D. Configure the MAC address of the server as a static entry associated with port Fa0/1.
Answer: B,D
Explanation:
You can use port security to block input to an Ethernet, Fast Ethernet, or Gigabit Ethernet port
when the MAC address of the station attempting to access the port is different from any of the
MAC addresses specified for that port.
When a secure port receives a packet, the source MAC address of the packet is compared to the
list of secure source addresses that were manually configured or autoconfigured (learned) on the
port. If a MAC address of a device attached to the port differs from the list of secure addresses,
the port either shuts down permanently (default mode), shuts down for the time you have
specified, or drops incoming packets from the insecure host. The port's behavior depends on how
you configure it to respond to a security violation.
When a security violation occurs, the Link LED for that port turns orange, and a link-down trap is
sent to the Simple Network Management Protocol (SNMP) manager. An SNMP trap is not sent if
you configure the port for restrictive violation mode. A trap is sent only if you configure the port to
shut down during a security violation.
QUESTION NO: 34
Refer to the exhibit. Some 2950 series switches are connected to the conference area of the
corporate headquarters network. The switches provide two to three jacks per conference room to
host laptop connections for employees who visit the headquarters office. When large groups of
employees come from other locations, the network administrator often finds that hubs have been
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 25
BeITCert
ified.c
om
connected to wall jacks in the conference area although the ports on the access layer switches
were not intended to support multiple workstations.
What action could the network administrator take to prevent access by multiple laptops through a
single switch port and still leave the switch functional for its intended use?
A. Configure static entries in the switch MAC address table to include the range of addresses used
by visiting employees.
B. Configure an ACL to allow only a single MAC address to connect to the switch at one time.
C. Use the mac-address-table 1 global configuration command to limit each port to one source
MAC address.
D. Implement Port Security on all interfaces and use the port-security maximum 1 command to
limit port access to a single MAC address.
E. Implement Port Security on all interfaces and use the port-security mac-address sticky
command to limit access to a single MAC address.
F. Implement Port Security at global configuration mode and use the port-security maximum 1
command to allow each switch only one attached hub.
Answer: D
QUESTION NO: 35
This output is generated by a switch that has 24 ports, however, some of the ports missing from
VLAN1. Why?
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 26
BeITCert
ified.c
omA. The missing ports are configured as trunk ports.
B. The missing ports are in VLAN 86.
C. The missing ports are administratively disabled.
D. The missing ports have a status problem such as a speed or duplex mismatch.
Answer: A
Explanation:
The show vlan command displays the VLAN information and ports in all VLANs. This command
displays only the ports in access mode. The missing ports must be configured as trunks.
QUESTION NO: 36
What can be determined from the router output shown in the graphic?
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 27
BeITCert
ified.c
omA. 200.1.1.64 is a default route.
B. The output shows that there are three default routes.
C. The output came from router R2.
D. The output came from a router that has four physical interfaces.
E. EIGRP is in use in this network.
Answer: E
Explanation:
In the routing table the "D" letter marks the route learned from EIGRP routing protocol. Based on
the routing table above, there are 4 directly connected IP interfaces, 2 EIGRP learned routes
(which means that EIGRP is in use on this network) and a static default route was also configured.
QUESTION NO: 37
The following is the graphic and routing table for router R1. Based on the output of the R1# show
ip route command and the information displayed in the graphic, which of the following is a potential
routing problem?
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 28
BeITCert
ified.c
omA. the use of summarization for discontiguous networks
B. the use of CIDR with a routing protocol that does not support it
C. the use of VLSM with a routing protocol that does not support it
D. the use of the no auto-summary command with a protocol that does not support summarization
E. the use of the ip route 0.0.0.0 0.0.0.0 command with a routing protocol that does not support it
Answer: A
Explanation:
By default, EIGRP will automatically summarize networks at their network boundary, which can
cause problems with dis-contiguous IP networks. Since the IP routing table does indeed show a
summary route to null 0, the default behavior of EIGRP was not modified. In this network, it would
be best to disable the automatic summarization feature of EIGRP.
QUESTION NO: 38
A company with 25 computers decides to connect its network to the Internet. The company would
like for all of the computers to have access to the Internet at the same time, but the company only
has four usable public IP addresses. What should be configured on the router so that all
computers can connect to the Internet simultaneously?
A. static NAT
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 29
BeITCert
ified.c
om
B. global NAT
C. dynamic NAT
D. static NAT with ACLs
E. dynamic NAT with overload
Answer: E
Explanation:
NAT overload, also called many to one NAT or Port Address Translation (PAT) allows for many IP
hosts to share a single IP address when connecting to the outside. In this case, the use of
dynamic NAT with overloading will allow for the 25 hosts to use an IP address from the NAT pool,
which will contain the 4 public IP addresses.
QUESTION NO: 39
The Company frame relay network is displayed as follows:
Which statement describes DLCI 17?
A. DLCI 17 describes a PVC on R2. It cannot be used on R3 or R1.
B. DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider.
C. DLCI 17 describes the ISDN circuit between R2 and R3.
D. DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.
Answer: D
Explanation:
DLCI-Data Link Connection Identifier Bits: The DLCI serves to identify the virtual connection so
that the receiving end knows which information connection a frame belongs to. Note that this DLCI
has only local significance. Frame Relay is strictly a Layer 2 protocol suite
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 30
BeITCert
ified.c
om
QUESTION NO: 40
When receiving a unicast frame with a destination MAC that is listed in the switch table, what will
an Ethernet switch do?
A. The switch will return a copy of the frame out the source port.
B. The switch will forward the frame to a specific port.
C. The switch will not forward unicast frames.
D. The switch will remove the destination MAC from the switch table.
E. The switch will forward the frame to all ports except the port on which it was received.
Answer: B
QUESTION NO: 41
Based on the exhibit provided, which access layer switch port will assume the discarding role at
the end of an RSTP election process?
A. Switch 4, port fa0/11
B. Switch 3, port Gi0/1
C. Switch 4, port fa0/2
D. Switch 3, port Gi0/2
Answer: A
QUESTION NO: 42
Study the exhibit presented carefully. What is the most efficient summarization that can be used
by R1 to advertise its networks to R2?
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 31
BeITCert
ified.c
omA. 172.1.0.0/22
B. 172.1.4.0/24
172.1.5.0/24
172.1.6.0/24
172.1.7.0/24
C. 172.1.4.0/22
D. 172.1.0.0/21
Answer: C
QUESTION NO: 43
Refer to the exhibit. SwX was taken out of the production network for maintenance.
It will be reconnected to the Fa0/16 port of Sw-AC3. What happens to the network when it is
reconnected and a trunk exists between the two switches?
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 32
BeITCert
ified.c
om
SwX#show vlan | SwX#show vtp stat
Sw-AC3#show vtp stat
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 33
BeITCert
ified.c
om
Sw-AC3#show vlan
A. All existing switches will have the students,admin,faculty,Servers,Management,Production,and
no-where VLANs.
B. All VLANs except the default VLAN will be removed from all switches.
C. The VLANs Servers,Managements,Production,and no-where will be removed from existing
switches.
D. The VLANs Servers,Management,Production,and no-where will replace the VLANs on SwX.
Answer: C
QUESTION NO: 44
A network administrator is trying to add a new router into an established OSPF network. The
networks attached to the new router do not appear in the routing tables of the other OSPF routers.
Given the information in the partial configuration shown below, what configuration error is causing
this problem?
Router (config)# router ospf 1
Router (config-router)# network 10.0.0.0 255.0.0.0 area 0
A. The process id is configured improperly.
B. The OSPF area is configured improperly.
C. The network wildcard mask is configured improperly.
D. The network number is configured improperly.
E. The AS is configured improperly.
F. The network subnet mask is configured improperly.
Answer: C
Explanation:
The network command specifies the IP address (10.10.10.0) followed by the wildcard mask (not
the subnet mask) and the area that is to be associated with the OSPF address range (in this case,
area 0). The wildcard mask indicates in binary how much of the IP address much be matched with
0s indicating that the bits must match and 1 indicating that they may vary. Thus 0.0.0.255 or
00000000.00000000.00000000.11111111 indicates that any bit in the last octet can vary while all
bits in the first 3 octets must match the network address (in other words, 10.10.10.xx)
Incorrect Answers:
A: This is not the problem, assuming that all 10.X.X.X networks are to be configured for OSPF.
D: Here the process ID is 99, which is valid.
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 34
BeITCert
ified.c
om
QUESTION NO: 45
Based on the topology table that is shown in the exhibit and assuming that variance is not
configured for EIGRP, which route or routes should appear in the routing table?
A. D 192.168.2.0/24 [90/3815424] via 192.168.8.18, 00:27:50, Serial0/2
B. D 192.168.2.0/24 [90/2707456] via 192.168.8.22, 00:27:50, Serial0/0 [90/3815424] via
192.168.8.18, 00:27:50, Serial0/2
C. D 192.168.8.24/30 [90/2681856] via 192.168.8.22, 00:27:50, Serial0/0
D. D 192.168.8.20 (2707456/2195456), Serial0/1
Answer: C
QUESTION NO: 46
Refer to the topology and partial router configurations shown in the exhibit. The network is fully
operational and all routing tables are converged. Which route will appear in the output of the show
ip route command issued on the Branch router?
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 35
BeITCert
ified.c
omA. S* 0.0.0.0/0 [1/0] via 192.168.10.82
B. R 172.16.11.4/30 [120/1] via 192.168.10.82, 00:00:22, Serial0/0
C. R 192.168.10.80/30 [120/0] via 192.168.10.81, 00:00:22, Serial0/0
D. R 192.168.11.0/24 [120/1] via 192.168.10.81, 00:00:22, Serial0/0
E. C 192.168.12.0/24 is directly connected, FastEthernet0/0
Answer: A
QUESTION NO: 47
PPP is short for Point-to-Point Protocol. Which PPP subprotocol negotiates authentication
options?
A. ISDN
B. LCP
C. NCP
D. SLIP
E. DLCI
Answer: B
Explanation:
LCP: A method of establishing, configuring, maintaining, and terminating the point-to-point
connection.
Link-establishment phase LCP packets are sent by each PPP device to configure and test the
link. These packets contain a field called the Configuration Option that allows each device to see
the size of the data, compression, and authentication. If no Configuration Option field is present,
then the default configurations are used.
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 36
BeITCert
ified.c
om
QUESTION NO: 48
What is the purpose of the command shown below?
vtp password Fl0r1da
A. It is used to validate the sources of VTP advertisements sent between switches.
B. It is used to access the VTP server to make changes to the VTP configuration.
C. It allows two VTP servers to exist in the same domain, each configured with different
passwords.
D. It is the password required when promoting a switch from VTP client mode to VTP server
mode.
E. It is used to prevent a switch newly added to the network from sending incorrect VLAN
information to the other switches in the domain.
Answer: A
QUESTION NO: 49
Why has the network shown in the exhibit failed to converge?
A. The no auto-summary command needs to be applied to the routers.
B. The network numbers have not been properly configured on the routers.
C. The subnet masks for the network numbers have not been properly configured.
D. The autonomous system number has not been properly configured.
E. The bandwidth values have not been properly configured on the serial interfaces.
Answer: A
Explanation:
To restore the default behavior of automatic summarization of subnet routes into network-level
routes, use the auto-summary command in router configuration mode. To disable this function and
transmit subprefix routing information across classful network boundaries, use the no form of this
command. Without disabling auto summarization, each router will advertise the 192.168.20.0/24
route, and the specific /26 networks will not be known.
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 37
BeITCert
ified.c
om
QUESTION NO: 50
Which IP addressing scheme is correct about the topology displayed in the exhibit?
A. host 1 - 192.168.10.22/24;
host 2 - 192.168.10.23/24;
host 3 -192.168.11.23/24
B. host 1 - 192.168.10.22/24;
host 2 - 192.168.10.23/24;
host 3 192.168.10.24/24
C. host 1 - 192.168.10.22/24;
host 2 - 192.168.11.23/24;
host 3 - 192.168.10.23/24
D. host 1 - 192.168.11.22/24;
host 2 - 192.168.11.23/24;
host 3 -192.168.10.24/24
Answer: C
Explanation:
Hosts in the same VLAN must belong to the same IP subnet. In this case, hosts A and C should
have IP addresses in one subnet, and host B should have an IP address in a separate subnet.
Only choice A is correct.
Incorrect Answers:
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 38
BeITCert
ified.c
om
A: In this case, all three hosts are in the same 192.168.10.0/24 subnet, even though there are 2
different VLANs
B: In this case, hosts A and B are both in the 192.168.10.0/24 subnet, but they are in different
VLANs
D: Here hosts A and B are both in the 192.168.11.0/24 subnet even though they are in different
VLANs.
QUESTION NO: 51
Which of the following statements describe the network shown in the graphic? (Choose two.)
A. There are two broadcast domains in the network.
B. There are five collision domains in the network.
C. There are four collision domains in the network.
D. There are seven collision domains in the network.
E. There are six broadcast domains in the network.
F. There are four broadcast domains in the network.
Answer: A,D
QUESTION NO: 52
Part of the Company WAN is shown below:
Refer to the exhibit. Subnet 10.1.3.0/24 is unknown to router RTB. Which router command will
prevent router RTB from dropping a packet destined for the 10.1.3.0/24 network if a default route
is configured?
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 39
BeITCert
ified.c
om
A. ip default-network
B. network 10.1.1.0
C. ip classless
D. network 10.1.1.0 0.0.0.255 area 0
Answer: C
QUESTION NO: 53
You are a network administrator . You have added a new subnet with 60 hosts to the company
network. To provide enough usable addresses while wasting the fewest addresses, which subnet
address should this network use?
A. 192.168.1.64/27
B. 192.168.1.64/26
C. 192.168.1.56/27
D. 192.168.1.56/26
Answer: B
Explanation:
.
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 40
BeITCert
ified.c
om
QUESTION NO: 54
Match the proper relationship between each category and its corresponding router output line.
Each router output line is the result of a show ip interface command. Not all categories are used
1. Layer 1 problem
2. Layer 2 problem
3. Layer 3 problem
4. port operational
5. port disabled
I) Serial0/1 is up, line protocol is up
II) Serial0/1 is up, line protocol is down
III) Serial0/1 is down, line protocol is down
IV) Serial0/1 is administratively down, line protocol is down
A. I-4;II-2;III-1;IV-5
B. I-4;II-3;III-1;IV-5
C. I-4;II-3;III-2;IV-5
D. I-4;II-2;III-1;IV-3
Answer: A
Explanation:
.
QUESTION NO: 55
For the following access list statements, which one will block all traffic with a destination TCP port
number of 5190 while not affecting other traffic?
A. access-list 180 deny tcp any any eq 5190
B. access-list 180 deny tcp any eq 5190 any
C. access-list 180 deny ip any eq 5190 any
D. access-list 180 deny tcp any eq 5190
E. access-list 180 deny telnet any any 5190
Answer: A
Explanation:
Creating an extended ACL: These lists are created and applied to an interface as either inbound
or outbound packet filters. They are implemented in this format: Access-list [list number] [permit |
deny] [protocol] [source address] [source-mask] [destination address] [destination-mask] [operator]
[port] [log] List Number -A number between 100 and 199 (Think of it as the name of the list.)
Permit | Deny -Whether to permit or deny this packet of information if conditions match Protocol -
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 41
BeITCert
ified.c
om
Type of protocol for this packet (i.e., IP, ICMP, UDP, TCP, or protocol number) Source Address -
Number of the network or host that the packet is from (Use the dotted-decimal format
192.168.1.12 or use the keyword ANY as an abbreviation for an address of 0.0.0.0
255.255.255.255 or use HOST and the dotted-decimal address.) Source Mask -The network mask
to use with the source address (Cisco masks are a little different, 0 = octet must match exactly;
255 = octet is not significant or doesn't matter.) Destination Address -The address that the packet
is going to, or ANY Destination Mask -The network mask to use with the destination address (if
you specify one) Operator (optional entry)-This applies to TCP or UDP ports only eq=equal lt=less
than gt=greater than neq=not equal range=a range of ports; you must specify two different port
numbers est=established connections Port (optional entry)-TCP/UDP destination port number or
service Log -Whether to log (if logging is enabled) this entry to the console
A sample inbound ACL would be: access-list 100 deny ip 10.0.0.0 0.255.255.255 any log access-
list 100 deny ip 172.16.0.0 0.15.255.255 any log access-list 100 deny ip 192.168.0.0 0.0.255.255
any log access-list 100 deny ip any host 127.0.0.1 log access-list 100 permit ip any [your network
IP address] [your network mask] est access-list 100 deny ip [your network IP address] [your
network mask] any log access-list 100 deny tcp any any eq 22222 access-list 100 deny tcp any
any range 60000 60020 log access-list 100 deny udp any any eq snmp log access-list 100 permit
ip any any
Reference: http://articles.techrepublic.com.com/5100-1035_11-1058307.html
QUESTION NO: 56
Multiple copies of the same unicast frame are likely to be transmitted in a switched LAN in which
circumstance?
A. when a dual ring topology is in use
B. in an improperly implemented redundant topology
C. when upper-layer protocols require high reliability
D. after broken links are re-established
E. during high traffic periods
Answer: B
Explanation:
A redundant topology eliminates single points of failure, but it also causes broadcast storms,
multiple frame copies, and MAC address table instability problems. Multiple Frame Copies--when
a new switch is added, the other switches may not have learned its correct MAC address. The
host may send a unicast frame to the new switch. The frame is sent through several paths at the
same time. The new switch will receive several copies of the frame. This causes MAC database
instability. MAC database instability results when multiple copies of a frame arrive on different
ports of a switch. Layer 2 has no mechanism to stop the loop. This is the main reason for the
Spanning Tree Protocol(STP) IEEE 802.1d which was developed to prevent routing loops.
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 42
BeITCert
ified.c
om
If multiple connections between switches are created for redundancy purposes, network loops can
occur iin an imprperly designed topology. Spanning Tree Protocol (STP) is used to stop network
loops while still permitting redundancy.
QUESTION NO: 57
You are a network Administrator. Telnet has been used by unauthorized users to gain access to a
company router. You want to configure and apply an access list to allow Telnet access to the
router, but only from your computer. To allow only the IP address 172.16.3.3 to have Telnet
access to the router, which group of commands would be the best choice?
A. access-list 101 permit tcp any host 172.16.3.3 eq telnet
interface s0/0
ip access-group 101 in
B. access-list 3 permit host 172.16.3.3
line vty 0 4
access-class 3 in
C. access-list 101 permit tcp any host 172.16.3.3 eq telnet
access-list 101 permit ip any any
interface s0/0
ip access-group 101 in
D. access-list 3 permit host 172.16.3.3
line vty 0 4
ip access-group 3 in
Answer: B
Explanation:
To restrict incoming and outgoing connections between a particular vty (into a Cisco device) and
the addresses in an access list, use the access-class command in line configuration mode.
Example:
The following example defines an access list that permits only hosts on network 192.89.55.0 to
connect to the virtual terminal ports on the router:
access-list 12 permit 192.89.55.0 0.0.0.255
line 1 5
access-class 12 in
Reference:
http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_command_reference_chapter
09186a00800873c8.html#wp1017389
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 43
BeITCert
ified.c
om
QUESTION NO: 58
You work as a network engineer, study the exhibit carefully. The routers are running RIPv2. Which
one of the following addressing schemes could meet the needs of this network yet waste the
fewest addresses?
A. Network 1: 192.168.10.0/27
Network 2: 192.168.10.64/28
Network 3: 192.168.10.96/29
Serial link 1: 192.168.10.112/30
Serial link 2: 192.168.10.116/30
B. Network 1: 192.168.10.0/26
Network 2: 192.168.10.64/27
Network 3: 192.168.10.96/28
Serial link 1: 192.168.10.112/30
Serial link 2: 192.168.10.116/30
C. Network 1: 192.168.10.0/26
Network 2: 192.168.10.64/28
Network 3: 192.168.10.80/29
Serial link 1: 192.168.10.88/30
Serial link 2: 192.168.10.96/30
D. Network 1: 192.168.10.0/26
Network 2: 192.168.10.64/26
Network 3: 192.168.10.128/26
Serial link 1: 192.168.20.0/24
Serial link 2: 192.168.30.0/24
Answer: B
QUESTION NO: 59
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 44
BeITCert
ified.c
om
A network administrator wants to ensure that only the server can connect to port Fa0/1 on a
Catalyst switch. The server is plugged into the switch Fa0/1 port and the network administrator is
about to bring the server online. What can the administrator do to ensure that only the MAC
address of the server is allowed by switch port Fa0/1? (Choose two.)
A. Configure port Fa0/1 to accept connections only from the static IP address of the server.
B. Configure the MAC address of the server as a static entry associated with port Fa0/1.
C. Configure port security on Fa0/1 to reject traffic with a source MAC address other than that of
the server.
D. Employ a proprietary connector type on Fa0/1 that is incompatible with other host connectors.
Answer: B,C
Explanation:
You can use port security to block input to an Ethernet, Fast Ethernet, or Gigabit Ethernet port
when the MAC address of the station attempting to access the port is different from any of the
MAC addresses specified for that port.
When a secure port receives a packet, the source MAC address of the packet is compared to the
list of secure source addresses that were manually configured or autoconfigured (learned) on the
port. If a MAC address of a device attached to the port differs from the list of secure addresses,
the port either shuts down permanently (default mode), shuts down for the time you have
specified, or drops incoming packets from the insecure host. The port's behavior depends on how
you configure it to respond to a security violation.
When a security violation occurs, the Link LED for that port turns orange, and a link-down trap is
sent to the Simple Network Management Protocol (SNMP) manager. An SNMP trap is not sent if
you configure the port for restrictive violation mode. A trap is sent only if you configure the port to
shut down during a security violation.
QUESTION NO: 60
To support the following IP addressing scheme, which routing protocols will be used? (Choose
three.)
Network 1 - 192.168.10.0 /26
Network 2 - 192.168.10.64 /27
Network 3 - 192.168.10.96 /27
Network 4 - 192.168.10.128 /30
Network 5 - 192.168.10.132 /30
A. EIGRP
B. IGRP
C. OSPF
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 45
BeITCert
ified.c
om
D. RIP version 2
E. RIP version 1
F. VTP
G. CDP
Answer: A,C,D
Explanation:
EIGRP and OSPF support Variable Length Subnet Masks (VLSM) and provide for both automatic
and manual route summarization configurations. RIPv2 is an enhanced version of RIP, and
overcame some of the limitations of RIP by introducing support for VLSM.
Incorrect Answers:
B: IGRP and RIP are relatively old and simplistic routing protocols that were developed before the
concepts of VLSM and route summarization.
E: IGRP and RIP are relatively old and simplistic routing protocols that were developed before the
concepts of VLSM and route summarization.
F: VTP is the VLAN Trunking Protocol, used in switched LAN environments to carry VLAN
information. It is not a routing protocol.
G: CDP is the Cisco Discovery Protocol, used between neighboring Cisco devices to automatically
discover information. It is not a routing protocol.
QUESTION NO: 61
A network administrator would like to implement NAT in the network shown in the graphic to allow
inside hosts to use a private addressing scheme. Where should NAT be configured?
A. Corporate router
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 46
BeITCert
ified.c
om
B. Engineering router
C. Sales router
D. all routers
E. all routers and switches
Answer: A
Explanation:
NAT should always be configured on the border device. It can be a either a border router or a PIX
firewall connecting to the Internet.
QUESTION NO: 62
Look at the graphic in the following. With the output from the router, can you determine which of
the following are correct? (Choose two.)
A. Router R uses a link-state routing protocol.
B. Router R will send routing updates out the Serial0/1 interface.
C. Router R will receive routing updates on the Serial0/0 interface.
D. Router R will send routing updates out the Serial0/0 interface.
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 47
BeITCert
ified.c
om
Answer: C,D
Explanation:
.
QUESTION NO: 63
Identify the four valid IPv6 addresses. (Choose four.)
A. 2000::
B. 2002:c0a8:101::42
C. 2003:dead:beef:4dad:23:46:bb:101
D. ::192:168:0:1
E. 2001:3452:4952:2837::
F. ::
Answer: B,C,D,F
Explanation:
From RFC 1884: IP Version 6 Addressing Architecture
There are three conventional forms for representing IPv6 addresses as
text strings:
1. The preferred form is x:x:x:x:x:x:x:x, where the 'x's are the
hexadecimal values of the eight 16-bit pieces of the address.
Examples:
FEDC:BA98:7654:3210:FEDC:BA98:7654:3210
1080:0:0:0:8:800:200C:417A
Note that it is not necessary to write the leading zeros in an
individual field, but there must be at least one numeral in
every field (except for the case described in 2.).
2. Due to the method of allocating certain styles of IPv6
addresses, it will be common for addresses to contain long
strings of zero bits. In order to make writing addresses
containing zero bits easier a special syntax is available to
compress the zeros. The use of "::" indicates multiple groups
of 16-bits of zeros. The "::" can only appear once in an
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 48
BeITCert
ified.c
om
address. The "::" can also be used to compress the leading
and/or trailing zeros in an address.
For example the following addresses:
1080:0:0:0:8:800:200C:417A a unicast address
FF01:0:0:0:0:0:0:43 a multicast address
0:0:0:0:0:0:0:1 the loopback address
0:0:0:0:0:0:0:0 the unspecified addresses
may be represented as:
1080::8:800:200C:417A a unicast address
FF01::43 a multicast address
::1 the loopback address
:: the unspecified addresses
3. An alternative form that is sometimes more convenient when
dealing with a mixed environment of IPv4 and IPv6 nodes is
x:x:x:x:x:x:d.d.d.d, where the 'x's are the hexadecimal values
of the six high-order 16-bit pieces of the address, and the 'd's
are the decimal values of the four low-order 8-bit pieces of the
address (standard IPv4 representation). Examples:
0:0:0:0:0:0:13.1.68.3
0:0:0:0:0:FFFF:129.144.52.38
or in compressed form:
::13.1.68.3
::FFFF:129.144.52.38
Reference : http://www.faqs.org/rfcs/rfc1884.html
.
QUESTION NO: 64
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 49
BeITCert
ified.c
om
Company Widgets is redesigning the network that connects its three locations, The administrator
gave the networking team 192.168.186.0 to use for addressing the entire network. After subnetting
the address, the team is ready to assign the addresses. The administrator plans to configure ip
subnet-zero and use RIP v2 as the routing protocol. As a member of the networking team, you
must address the network and at the same time conserve unused addresses for future growth.
With those goals in mind, assign the correct host addresses for the router interface. One of the
routers is partially configured. Not all of the host addresses are necessary.
I) 192.168.186.173/26
II) 192.168.186.129/30
III) 192.168.186.128/30
IV) 192.168.186.152/28
V) 192.168.186.143/29
VI) 192.168.186.3/25
A. 1-VI;2-II;3-I;4-IV
B. 1-VI;2-I;3-II;4-V
C. 1-V;2-II;3-II;4-IV
D. 1-VI;2-I;3-III;4-IV
Answer: A
Explanation:
.
QUESTION NO: 65
In order to establish a secure terminal connection to a remote network device, which protocol will
you use?
A. SNMPv1
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 50
BeITCert
ified.c
om
B. WEP
C. SSH
D. SNMPv2
E. ARP
F. Telnet
Answer: C
QUESTION NO: 66
In an improperly implemented redundant topology, multiple copies of the same unicast frame are
likely to be transmitted in a switched LAN
A. False
B. True
Answer: B
Explanation:
.
QUESTION NO: 67
What does STATUS=ACTIVE indicate based on the output of the show frame-relay pvc
command?
A. The Frame Relay switch is correctly programmed with the DLCI and is operational.
B. The router R1 is actively broadcasting to establish a link to the Frame Relay switch.
C. The router R1 is connected to the local Frame Relay switch, but not to the far end device.
D. The PVC is experiencing congestion.
Answer: A
Cisco 640-816: Practice Exam
"Pass Any Exam. Any Time." - 100% Guaranteed 51