(tecumseh), tcci (york) compressor clutches...blissfield (tecumseh), tcci (york) compressor clutches...

23
PAGE 396 75R SERIES CLUTCH SPECIFICATIONS Clutches are sorted by increasing size of Pulley Diameter [A] [A] | [ C] [B] Pulley | Gauge Line Red Dot Red Dot Diameter | Grooves Width Dimension Volts Description No. Factory No. 5” Poly 6 0.14 12 double wire / Metripack plug 75R4812 RD-5-13784-0P 5 3⁄8” Poly 8 0.14 1 5⁄8” 12 single wire with diode / Female Weatherpak (IHC) plug 75R0662 RD-5-9802-0P 5 ” Poly 6 0.14 2” 12 double wire with diode / Metripak plug 75R0502 RD-5-10363-0P 5 ” Poly 6 0.14 2” 12 single wire with diode / Weatherpak plug 75R0512 RD-5-10364-0P 5 7⁄8” Poly 6 0.14 1 5⁄8” 12 double wire with diode / Metripak plug 75R0522 RD-5-10366-0P 6” 1 2 ” 12 single wire with diode / Weatherpak plug 75R0302 RD-5-4966-0P 6” 1 2 ” 12 single wire with diode / Female Weatherpak (IHC) plug 75R0402 RD-5-9665-0P 6” 2 1 5⁄8” 12 single wire with diode / Weatherpak plug 75R1202 RD-5-4972-1P 6” 2 1 5⁄8” 12 double wire with diode / Metripak plug 75R1302 RD-5-9456-0P 6” 2 2 ” 12 single wire / Female Weatherpak (IHC) plug 75R0422 RD-5-10367-0P 6” 2 2 ” 24 single wire / Male bullet plug 75R4734 RD-5-9659-0P 6 1⁄8” Poly 6 0.14 12 single wire with diode / Female Weatherpak (IHC) plug 75R0612 RD-5-8009-0P 6 1⁄8” Poly 8 0.14 1 15⁄16” 12 double wire with diode / Metripak plug 75R0682 RD-5-10365-0P 6 ” 1 5⁄8” 2 11⁄16” 12 single wire / Female Weatherpak (IHC) plug 75R1342 RD-5-10397-0P 6 ” 1 5⁄8” 1 ” 12 single wire / Male bullet plug 75R1652 RD-5-4975-0P 7” 2 2” 12 single wire / Male bullet plug 75R4502 RD-5-4994-0P 7” 2 2” 24 single wire / Male bullet plug 75R4534 RD-5-8382-0P BLISSFIELD ( TECUMSEH ) , TCCI ( YORK ) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read use following procedure to determine required clutch part number. 1. Determine if clutch is double or single groove. 2. Determine if 12 or 24 volt. 3. Measure outside diameter “A” of pulley. 4. Measure width of pulley groove “C”. 5. Measure the “B” dimension accurately. l Clutches are listed by pulley diameter l All keys are 5 32”. l “D” dimension is 0.62” on all double groove clutches. C A D B 75R0302 RD-5-4966-0P OE #L50-2409 Diameter: 6” Groove: 1 Width: ” 12 Volts B Dimension: 2 ” Single wire coil w diode Weatherpak plug 75R0402 RD-5-9665-0P OE #508888 Diameter: 6” Groove: 1 Width: ” 12 Volts B Dimension: 2 ” Single wire coil Female Weatherpak (IHC) plug 75R0422 RD-5-10367-0P Diameter: 6” Groove: 2 Width: ” 12 Volts B Dimension: 2 ” Single wire coil Female Weatherpak (IHC) plug 75R0452 RD-5-4967-0P OE #501215 Diameter: 6” Groove: 2 Width: ” 12 Volts B Dimension: 1 5⁄8” Single wire coil Male bullet plug

Upload: others

Post on 15-Mar-2020

111 views

Category:

Documents


1 download

TRANSCRIPT

Page 1: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 396

75R SERIES

CLUTCH SPECIFICATIONS Clutches are sorted by increasing size of Pulley Diameter [A]

[A] | [C] [B] Pulley | Gauge Line Red Dot Red Dot Diameter | Grooves Width Dimension Volts Description No. Factory No. 5” Poly 6 0.14 — 12 double wire / Metripack plug 75R4812 RD-5-13784-0P 5 3⁄8” Poly 8 0.14 1 5⁄8” 12 single wire with diode / Female Weatherpak (IHC) plug 75R0662 RD-5-9802-0P 5 3⁄4” Poly 6 0.14 2” 12 double wire with diode / Metripak plug 75R0502 RD-5-10363-0P 5 3⁄4” Poly 6 0.14 2” 12 single wire with diode / Weatherpak plug 75R0512 RD-5-10364-0P 5 7⁄8” Poly 6 0.14 1 5⁄8” 12 double wire with diode / Metripak plug 75R0522 RD-5-10366-0P 6” 1 1⁄2” 2 3⁄4” 12 single wire with diode / Weatherpak plug 75R0302 RD-5-4966-0P 6” 1 1⁄2” 2 3⁄4” 12 single wire with diode / Female Weatherpak (IHC) plug 75R0402 RD-5-9665-0P 6” 2 1⁄2” 1 5⁄8” 12 single wire with diode / Weatherpak plug 75R1202 RD-5-4972-1P 6” 2 1⁄2” 1 5⁄8” 12 double wire with diode / Metripak plug 75R1302 RD-5-9456-0P 6” 2 1⁄2” 2 1⁄4” 12 single wire / Female Weatherpak (IHC) plug 75R0422 RD-5-10367-0P 6” 2 1⁄2” 2 1⁄4” 24 single wire / Male bullet plug 75R4734 RD-5-9659-0P 6 1⁄8” Poly 6 0.14 — 12 single wire with diode / Female Weatherpak (IHC) plug 75R0612 RD-5-8009-0P 6 1⁄8” Poly 8 0.14 1 15⁄16” 12 double wire with diode / Metripak plug 75R0682 RD-5-10365-0P 6 1⁄4” 1 5⁄8” 2 11⁄16” 12 single wire / Female Weatherpak (IHC) plug 75R1342 RD-5-10397-0P 6 3⁄4” 1 5⁄8” 1 3⁄4” 12 single wire / Male bullet plug 75R1652 RD-5-4975-0P 7” 2 1⁄2” 2” 12 single wire / Male bullet plug 75R4502 RD-5-4994-0P 7” 2 1⁄2” 2” 24 single wire / Male bullet plug 75R4534 RD-5-8382-0P

BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES

= Limited to stock on hand

If part number on clutch being replaced cannot be read use following procedure to determine required clutch part number.1. Determine if clutch is double or single groove.2. Determine if 12 or 24 volt.3. Measure outside diameter “A” of pulley.4. Measure width of pulley groove “C”.5. Measure the “B” dimension accurately.

l Clutches are listed by pulley diameter

l All keys are 5⁄32”.l “D” dimension is 0.62” on

all double groove clutches.

C

A

DB

75R0302 RD-5-4966-0POE #L50-2409Diameter: 6”Groove: 1Width: 1⁄2” 12 Volts B Dimension: 2 3⁄4” Single wire coil w diodeWeatherpak plug

75R0402 RD-5-9665-0POE #508888Diameter: 6” Groove: 1Width: 1⁄2”12 Volts B Dimension: 2 3⁄4” Single wire coil Female Weatherpak (IHC) plug

75R0422 RD-5-10367-0P

Diameter: 6” Groove: 2Width: 1⁄2” 12 VoltsB Dimension: 2 1⁄4” Single wire coil Female Weatherpak (IHC) plug

75R0452 RD-5-4967-0POE #501215Diameter: 6”Groove: 2Width: 1⁄2” 12 VoltsB Dimension: 1 5⁄8” Single wire coil Male bullet plug

Page 2: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 397

75R SERIES BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES

75R0502 RD-5-10363-0POE #024-25244Diameter: 5 3⁄4”Groove: Poly 6Width: .14” 12 VoltsB Dimension: 2” Double wire coil with diodeMetripak plug

75R0512 RD-5-10364-0POE #14304, 23100SDiameter: 5 3⁄4” Groove: Poly 6Width: .14” 12 Volts B Dimension: 2” Single wire coil with diodeWeatherpak plug

75R0522 RD-5-10366-0POE #522583, MAE-MG07Diameter: 5 7⁄8”Groove: Poly 6Width: .14”12 VoltsB Dimension: 1 5⁄8” Double wire coil with diode,Metripak plug

75R0612 RD-5-8009-0POE #520226, MA-N03DDiameter: 6 1⁄8” Groove: Poly 6Width: .14” 12 Volts B Dimension: - Single wire coil with diode Female Weatherpak (IHC) plug

75R0662 RD-5-9802-0POE #515376, MA-N05Diameter: 5 3⁄8”Groove: Poly 8Width: .14” 12 VoltsB Dimension: 1 5⁄8” Single wire coil with diode Female Weatherpak (IHC) plug

75R0682 RD-5-10365-0POE #522584, MAE-MG01Diameter: 6 1⁄8” Groove: Poly 8Width: .14” 12 VoltsB Dimension: 1 15⁄16” Double wire coil with diodeMetripak plug

75R1202 RD-5-4972-1POE #501939, MAE-6ARDiameter: 6”Groove: 2Width: 1⁄2” 12 VoltsB Dimension: 1 5⁄8” Single wire coil with diode Weatherpak plug

75R1302 RD-5-9456-0POE #522582, MAE-06ADiameter: 6” Groove: 2Width: 1⁄2” 12 Volts B Dimension: 1 5⁄8” Double wire coil with diode Metripak plug

Page 3: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 398

75R SERIES

75R1342 RD-5-10397-0POE #515528, MA-N06D, 2035274C1Diameter: 6 1⁄4”Groove: 1Width: 5⁄8”12 Volts B Dimension: 2 11⁄16” Single wire coil Female Weatherpak (IHC) plug

75R1652 RD-5-4975-0POE #L50-2731Diameter: 6 3⁄4”Groove: 1Width: 5⁄8” 12 Volts B Dimension: 1 3⁄4” Single wire coil Male bullet plug

75R4502 RD-5-4994-0POE #332334, MA-7ADiameter: 7” Groove: 2Width: 1⁄2” 12 Volts B Dimension: 2” Single wire coil Male bullet plug

75R4534 RD-5-8382-0POE #501075, MA-7A 2, MA-7A 24VDiameter: 7” Groove: 2Width: 1⁄2” 24 VoltsB Dimension: 2” Single wire coilMale bullet plug

75R4734 RD-5-9659-0POE #501076, MA-6A-2, MA6A-24VDiameter: 6” Groove: 2Width: 1⁄2” 24 Volts B Dimension: 2 1⁄4” Single wire coilMale bullet plug

75R4812 RD-5-13784-0POE #4424-9931Diameter: 5” Groove: Poly 6Width: 0.14” 12 Volts Double wire coil with diode Metripack plug

BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES

Page 4: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 399

75R SERIES NIPPONDENSO / SAMLIN COMPRESSOR CLUTCHES

CLUTCH SPECIFICATIONS Clutches are sorted by increasing size of Pulley Diameter [A]

[A] | [C] [B] Pulley | Gauge Line Red Dot Red Dot Diameter | Grooves Width Dimension Volts Description No. Factory No. 4 1⁄2” Poly 7 1⁄8” 7⁄8” 12 FX-15 / 2 prong Ford integral, 21 spline 75R4762 RD-5-10359-0P 4 7⁄8” Poly 6 1⁄8” — 12 FS-6 / 2 prong Ford integral 75R4702 RD-5-10401-0P 5” Poly 6 1⁄8” 3⁄4” 12 FX-15 / 2 prong Ford integral, 21 spline 75R4742 RD-5-10357-0P 5 9⁄16” Poly 6 1⁄8” 3⁄4” 12 FX-15 / 2 prong Ford integral, 21 spline 75R4752 RD-5-10358-0P 5 7⁄8” 1 7⁄16” 1 3⁄8” 12 FS-6 / 3 eye-2 prong Ford integral 75R4732 RD-5-9657-0P

If part number on clutch being replaced cannot be read use following procedure to determine required clutch part number.1. Determine if clutch is double or single groove.2. Determine if 12 or 24 volt.3. Measure outside diameter “A” of pulley.4. Measure width of pulley groove “C”.5. Measure the “B” dimension accurately.

l Clutches are listed by pulley diameter

l All keys are 5⁄32”.l “D” dimension is 0.62” on

all double groove clutches.

C

A

DB

75R4702 RD-5-10401-0P

Model: FS-6Diameter: 4 7⁄8”Groove: Poly 6Width: 1⁄8”12 VoltsB Dimension: - Two-prongFord integral75R4732 RD-5-9657-0P

OE # 518484, FF-E4TH-BA1Model: FS-6Diameter: 5 7⁄8” Groove: 1Width: 7⁄16”12 Volts B Dimension: 1 3⁄8” Two-prong Ford integral75R4742 RD-5-10357-0P

OE # F10H-19D798AA, F20H-19D786-AAModel: FX-15Diameter: 5”Groove: Poly 6Width: 1⁄8”12 VoltsB Dimension: - 3⁄4” Two-prong Ford integral, 21 spline

75R4752 RD-5-10358-0P

Model: FX-15Diameter: 5 9⁄16” Groove: Poly 6Width: 1⁄8”12 Volts B Dimension: - 3⁄4” Two-prong Ford integral, 21 spline75R4762 RD-5-10359-0P

Model: FX-15Diameter: 4 1⁄2” Groove: Poly 7Width: 1⁄8” 12 VoltsB Dimension: - 7⁄8” Two-prong Ford integral, 21 spline

Page 5: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 400

75R SERIES SANDEN COMPRESSOR CLUTCHES

CLUTCH SPECIFICATIONS Clutches are sorted by increasing size of Pulley Diameter [A]

[A] | [C] [B] Pulley | Gauge Line Red Dot Red Dot Diameter | Grooves Width Dimension Volts Description No. Factory No.4.7” 119mm Poly 6 0.14 2 1⁄2”/ 63mm 12 709, 7H15 / double wire coil, male bullet 75R0032 RD-5-10398-0P4.7” 119mm Poly 7 0.14 — 12 SD5 (508, 510, 5H14) / single wire, male bullet 75R0042 RD-5-5574-0P4.7” 119mm Poly 7 0.14 1 7⁄8”/ 48mm 12 709, 7H15 / single wire coil, Weatherpak 75R0052 RD-5-10399-0P4.7” 119mm Poly 8 0.14 — 12 709, 7H15 / double wire coil, Metripak plug 75R1842 RD-5-10760-0P4.7” 119mm Poly 8 0.14 1 13⁄16”/ 46mm 12 709, 7H15 / single wire coil, male bullet 75R1862 RD-5-10762-0P4.9” 125mm 2 1⁄2” 2 5⁄32”/ 55mm 12 709, 7H15 / double wire coil, Metripak plug 75R1532 RD-5-10368-0P4.9” 125mm 2 1⁄2” — 12 SD7 / single wire coil, male bullet 75R0192 RD-5-7831-0P4.9” 125mm 2 1⁄2” 1 9⁄16”/ 40mm 24 709, 7H15 / single wire, fem. 280 HD Plug 75R0194 RD-5-7832-0P4.9” 125mm Poly 8 0.14 — 12 709, 7H15 / double wire coil, Ford OE Plug 75R1432 RD-5-10361-0P5 1⁄8” 130mm Poly 8 0.14 — 12 709, 7H15 / double wire coil, Metripak plug 75R4802 RD-5-11374-0P5 1⁄4” 132mm 2 1⁄2” 1 9⁄16”/ 40mm 12 SD5 (508, 510, 5H14) / single wire 75R0202 RD-5-5486-0P5 1⁄4” 132mm 2 1⁄2” 1 9⁄16”/40mm 24 SD5 (508, 510, 5H14) / single wire, male bullet 75R0204 RD-5-5487-0P5 1⁄4” 132mm 2 1⁄2” 1 9⁄16”/40mm 12 709, 7H15 / double wire coil, Ford OE Plug 75R1542 RD-5-10369-0P5 1⁄4” 132mm 2 1⁄2” — 12 709, 7H15 double wire coil, Metripak plug 75R1832 RD-5-10759-0P5 1⁄4” 132mm 2 1⁄2” — 12 709, 7H15 2 wire coil w diode, Metripak plug 75R1852 RD-5-10761-0P6 21⁄32” 169mm 1 1⁄2” 1 9⁄16”/ 40mm 12 709, 7H15 / double wire coil, Ford OE Plug 75R1512 RD-5-10360-0P

75R0032 RD-5-10398-0POE # 6524-6010Model 709 / 7H15Diameter: 4.7” / 119mm Groove: Poly 6Width: .14”12 Volts B Distance: 2 1⁄2”/ 63mm Double wire coilMale bullet plug

75R0042 RD-5-5574-0POE # 6520-6010Model SD5 (508, 510, 5H14) Diameter: 4.7” / 119mm Groove: Poly 7Width: .14”12 Volts B Distance: - Single wire coilMale bullet plug

= Limited to stock on hand

If part number on clutch being replaced cannot be read use following procedure to determine required clutch part number.1. Determine if clutch is double or single groove.2. Determine if 12 or 24 volt.3. Measure outside diameter “A” of pulley.4. Measure width of pulley groove “C”.5. Measure the “B” dimension accurately.

l Clutches are listed by pulley diameter

l All keys are 5⁄32”.l “D” dimension is 0.62” on

all double groove clutches.

C

A

DB

Page 6: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 401

75R SERIES SANDEN COMPRESSOR CLUTCHES

75R0052 RD-5-10399-0POE # 6512-6210Model 709 / 7H15Diameter: 4.7” / 119mm Groove: Poly 7Width: .14” 12 VoltsB Distance: 1 7⁄8”/ 48mm Single wire coilWeatherpak plug

75R0192 RD-5-7831-0P

OE # 4446-9931Model SD7Diameter: 4.9” / 125mm Groove: 2Width: 1⁄2”12 VoltsB Distance: - Single wire coilMale bullet plug

75R0194 RD-5-7832-0POE # 6511-6310Model 709 / 7H15Diameter: 4.9” / 125mm Groove: 2Width: 1⁄2” 24 VoltsB Distance: 1 9⁄16”/ 40mm Single wire coilFemale 280 HD plug

75R0202 RD-5-5486-0POE # 6575-6310Model SD5 (508, 510, 5H14) Diameter: 5 1⁄4” / 132mm Groove: 2Width: 1⁄2”12 VoltsB Distance: 1 9⁄16”/ 40mm Single wire coil Bare wire

75R0204 RD-5-5487-0POE # 6519-6210Model SD5 (508, 510, 5H14) Diameter: 5 1⁄4” / 132mm Groove: 2Width: 1⁄2”24 VoltsB Distance: 1 9⁄16”/ 40mm Single wire coilMale bullet plug

75R1432 RD-5-10361-0POE#6593-6010Model 709 / 7H15Diameter: 4.9” / 125mm Groove: Poly 8Width: .14” 12 Volts B Distance: - Double wire coil Ford OE plug

75R1532 RD-5-10368-0POE # 6593-6010, 4740-9931Model 709 / 7H15Diameter: 4.9” / 125mm Groove: 2Width: 1⁄2” 12 VoltsB Distance: 2 5⁄32”/ 55mm Double wire coil Metripak plug

75R1542 RD-5-10369-0POE # 6504-6010Model 709 / 7H15Diameter: 5 1⁄4” / 132mm Groove: 2Width: 1⁄2”12 VoltsB Distance: 1 9⁄16”/ 40mm Double wire coilFord OE plug

= Limited to stock on hand

Page 7: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 402

75R SERIES SANDEN COMPRESSOR CLUTCHES

75R1832 RD-5-10759-0POE # 4694-9931Model 709 / 7H15Diameter: 5 1⁄4” / 132mm Groove: 2Width: 1⁄2”12 VoltsB Distance: — Double wire coil Metripak plug

75R1842 RD-5-10760-0POE #4606-6871, 4705-9930, 9931Model 709 / 7H15Diameter: 4.7” / 119mm Groove: Poly 8Width: .14” 12 voltsB Distance: Double wire coil Metripak plug

75R1852 RD-5-10761-0POE # 4752-9931Model 709 / 7H15Diameter: 5 1⁄4” / 132mm Groove: 2Width: 1⁄2”12 voltsB Distance: — Double wire coil with diodeMetripak plug

75R1862 RD-5-10762-0POE #6522-6010, 9033-9900Model 709 / 7H15Diameter: 4.7” / 119mm Groove: Poly 8Width: .14” 12 voltsB Distance: 1 13⁄16”/ 46mm Single wire coilMale bullet plug

75R4802 RD-5-11374-0POE # 4885-9931Model 709 / 7H15Diameter: 5 1⁄8” / 130mm Groove: Poly 8Width: .14” 12 voltsB Distance: — Double wire coil w diode Metripak plug

Page 8: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 403

75R SERIES

CLUTCH SPECIFICATIONS Clutches are sorted by increasing size of Pulley Diameter [A]

[A] | [C] [B] Pulley | Gauge Line Red Dot Red Dot Diameter | Grooves Width Dimension Volts Description No. Factory No.4 27⁄32” 123mm Poly 6 0.14 1 11⁄32 / 34mm 12 Seltec TM15 / 3 eye hub; single wire, male bullet 75R0072 RD-5-10526-0P4 27⁄32” 123mm Poly 6 0.14 — 12 Seltec TM15 / spring leaf; single wire, male bullet 75R0092 RD-5-10545-0P4 27⁄32” 123mm Poly 8 0.14 1 11⁄32 / 34mm 12 Seltec TM15 / 3 eye hub; single wire, male bullet 75R0082 RD-5-10544-0P4.9” 125mm 1 1⁄2” 2 7⁄16”/62mm 12 Seltec/TAMA-CH / single wire coil, male bullet 75R0182 RD-5-6646-0P4.9” 125mm 2 1⁄2” 1 9⁄16”/40mm 12 Seltec TM15 / spring leaf; single wire, male bullet 75R0262 RD-5-10723-0P4.9” 125mm 2 1⁄2” — 12 ICE - TM16 / spring leaf; double wire, Metripak plug 75R1212 RD-5-10724-0P4.9” 125mm Poly 8 0.14 — 12 ICE - TM16 / double wire coil, Metripak plug 75R0062 RD-5-10727-0P5 21⁄64” 135mm 2 1⁄2” 1 9⁄16”/40mm 12 Seltec-CH / 3 eye hub; single wire, male bullet 75R0172 RD-5-11025-0P5 21⁄64” 135mm 2 1⁄2” — 12 Seltec TM15 / 3 eye hub; single wire, male bullet 75R0252 RD-5-10722-0P5 21⁄64” 135mm 2 1⁄2” 1 9⁄16”/40mm 24 Seltec TM15 / 3 eye hub; single wire, male bullet 75R0274 RD-5-10232-0P6” 152mm 2 1⁄2” 3” / 76mm 12 ICE TM31 / 5 eye hub; single wire, male bullet 75R4782 RD-5-10301-0P6” 152mm Poly 8 0.14 2 5⁄8” / 67mm 12 ICE TM31 / 5 eye hub; single wire, male bullet 75R4792 RD-5-10302-0P6 1⁄4” 159mm 1 1⁄2-3⁄4” var 1 7⁄8”/ 47mm 12 Seltec/ICE-CH / 3 eye hub; single wire, male bullet 75R1412 RD-5-9249-0P6 1⁄4” 159mm 1 1⁄2-3⁄4” var 1 7⁄8”/ 47mm 24 Seltec/ICE-CH / 3 eye hub; single wire, male bullet 75R1414 RD-5-9250-0P

SELTEC / ICE / DIESEL KIKI / TAMA / ZEXEL COMPRESSOR CLUTCHES

75R0062 RD-5-10727-0POE # 2570201Model: ICE - TM16Diameter: 4.9” / 125mm Groove: Poly 8Width: .14”12 Volts B Dimension: Double wire coil Metripak plug

75R0072 RD-5-10526-0POE # 2570144Model: Seltec - TM15Diameter: 4 27⁄32” / 123mmGroove: Poly 6Width: .14”12 Volts B Dimension: 1 11⁄32”/ 34 mm Single wire coil Male bullet plug

75R0082 RD-5-10544-0POE # 2570155Model: Seltec - TM15Diameter: 4 27⁄32” / 123mmGroove: Poly 8Width: .14”12 Volts B Dimension: 1 11⁄32”/ 34 mm Single wire coil Male bullet plug

75R0092 RD-5-10545-0POE # 2570161Model: Seltec - TM15Diameter: 4 27⁄32” / 123mmGroove: Poly 6Width: .14”12 VoltsB Dimension: - Single wire coil Male bullet plug

If part number on clutch being replaced cannot be read use following procedure to determine required clutch part number.1. Determine if clutch is double or single groove.2. Determine if 12 or 24 volt.3. Measure outside diameter “A” of pulley.4. Measure width of pulley groove “C”.5. Measure the “B” dimension accurately.

l Clutches are listed by pulley diameter

l All keys are 5⁄32”.l “D” dimension is 0.62” on

all double groove clutches.

C

A

DB

Page 9: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 404

75R SERIES SELTEC / ICE / DIESEL KIKI / TAMA / ZEXEL COMPRESSOR CLUTCHES

75R0172 RD-5-11025-0POE # 2570151Model: Seltec - CHDiameter: 5 21⁄64” / 135mmGroove: 2Width: 1⁄2” 12 Volts B Dimension: 1 9⁄16”/ 40 mm Single wire coil Male bullet plug

75R0182 RD-5-6646-0POE # 511869Model: Seltec/TAMA - CHDiameter: 4.9” / 125mm Groove: 1Width: 1⁄2” 12 Volts B Dimension: 2 7⁄16”/ 62 mm Single wire coil Male bullet plug

75R0252 RD-5-10722-0POE # 2570152Model: Seltec - TM15Diameter: 5 21⁄64” / 135mmGroove: 2 Width: 1⁄2”,12 Volts B Dimension: - Single wire coil Male bullet plug

75R0262 RD-5-10723-0POE # 2570159Model: Seltec - TM15Diameter: 4.9” / 125mm Groove: 2 Width: 1⁄2”12 Volts B Dimension: 1 9⁄16”/ 40 mm Single wire coilMale bullet plug

75R0274 RD-5-10232-0POE # 2570150Model: Seltec - TM15Diameter: 5 21⁄64” / 135mmGroove: 2 Width: 1⁄2”,24 Volts B Dimension: 1 9⁄16”/ 40 mm Single wire coil Male bullet plug

75R1212 RD-5-10724-0POE # 2570158Model: ICE - TM16Diameter: 4.9” / 125mmGroove: 2 Width: 1⁄2”,12 Volts B Dimension: - Double wire coil Metripak plug

75R1412 RD-5-9249-0POE # 2570148Model: Seltec - CHDiameter: 6 1⁄4” / 159mmGroove: 1Width: 1⁄2-3⁄4” variable 12 Volts B Dimension: 1 7⁄8”/ 47 mm Single wire coil Male bullet plug

75R1414 RD-5-9250-0POE # 2570149Model: Seltec - CHDiameter: 6 1⁄4” / 159mmGroove: 1Width: 1⁄2-3⁄4” variable 24 Volts B Dimension: 1 7⁄8”/ 47 mm Single wire coil Male bullet plug

Page 10: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 405

75R SERIES SELTEC / ICE / DIESEL KIKI / TAMA / ZEXEL COMPRESSOR CLUTCHES

75R4782 RD-5-10301-0POE # 2570165Model: ICE - TM31 Diameter: 6” / 152mm Groove: 2Width: 1⁄2 12 Volts B Dimension: 3”/ 76mm Single wire coil Male bullet plug

75R4792 RD-5-10302-0POE # 2570168Model: ICE - TM31 Diameter: 6” / 152mm Groove: Poly 8Width: .14 12 Volts B Dimension: 2 5⁄8”/ 67mm Single wire coil Male bullet plug

Page 11: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 406

75R SERIES

** For R12 installations use 75R5611 and 75R5618 Service Valves† G = Gates D = Dayco GY = Goodyear

COMPRESSOR MOUNT KIT & CLUTCH APPLICATION

IMPORTANT - READ THIS ENGINE MOUNT AND DRIVE ADAPTABILITY

Mount kits contain all components and hardware required to mount compressor to engine. Drive belt supplied with all kits except 75R9000 & 75R9895.

IMPORTANT Minor modifications are occasionally necessary and are considered part of an installation. These kits are designed to fit vehicles with standard equipment. Each model adapter kit is thoroughly checked by instal-lation of the bracket on a standard vehicle. The addition of special or optional equipment may interfere with normal installation. Compressor mounts are an accessory, and are of no concern to the engine manufacturer. Casting dimen-sions and bosses utilized in the bracket mounting vary as they are of no value to the engine manufacturer. Extra tolerances have been built into the bracket to compensate for these differences. It is important that proper pulley alignment

be assured before final tensioning of the mounting bolts. If sufficient tolerance has not been allowed for that particular engine, further modification, such as elongating a hole or reshaping a strap, may be necessary to achieve proper alignment and fit. Some installations may require a slight modification or rearrangement of radiator mounting, gas or water lines for proper clearance. Trucks are quite often custom built, and you may find differences in the sup-plier of power steering and other accessory equipment. It may be necessary to purchase a special accessory pulley, which is not furnished in the kit, from the truck distributor.

Manufacturer Year Engine Clutch R-134a Compressor

R-134a Charge Fitting

Compressor Mount Kit Number Belt No.†

MULTI-USE

Cat 3406B 6 Cyl 893 cu. in. 14.6 Liter 75R8382 75R8384 75R9780 G9550

Cummins 10 Liter 611 cu. in. 240 300 HP 75R8382 75R8384 75R9790

Cummins “N” Series 14 Liter (855 cu. in.) 300 thru 444 H.P. with second groove from engine open (accessary drive)

75R8382 75R8384 75R9890 G9550

Cat 3176 75R8382 75R9545

1990-95 Cummins L-10 75R8382 75R8384 75R9625 G9530

1994- Cummins M11 75R8382 75R8384 75R9625 G9530

Cummins 4BT & 6BT without idler pulley 75R8382 75R8384 75R9895

1992-95 Cummins 6BT - 5.9 Ltr. without air injection pump 75R8382 75R8384 75R9795

1991-95 Cummins 6C/6CT/6CTA 8.3L 75R8382 75R8384 75R9785

AUTOCAR

Series A, DC, KK Conventional 1966-89

Cummins “N” Series Full Flow Cooling Accessories Drive Pulley 208831 or 190448. Except 20° tilt or P/S on Accessory Drive

75R7280 75R5681** 75R5688** 75R9220

1966-89 Cummins “N” 75R8382 75R9670

1966-88 Cummins “N” Series 75R7280 75R5681** 75R5688** 75R9220

1970-89 Detroit Diesel 6V or 8V-92 75R1202 75R7280 75R5681** 75R5688** 75R9060 G9375

BUCYRUS

Erie 88B Excavator Cummins KT1150 75R8372 75R8374 75R9835

BOMAG

BW 851 Compactor Cummins 1150 75R8372 75R8374 75R9835

K351 Compactor Cummins 855 75R8422 75R8424 75R9870

Page 12: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 407

75R SERIES

** For R12 installations use 75R5611 and 75R5618 Service Valves† G = Gates D = Dayco GY = Goodyear

COMPRESSOR MOUNT KIT & CLUTCH APPLICATION

Manufacturer Year Engine Clutch R-134a Compressor

R-134a Charge Fitting

Compressor Mount Kit Number Belt No.†

CASE580L, 480E, 480F Backhoe Cummins 4-390 75R8422

75R8424 75R9840

680L, 780D Backhoe Cummins 6-590 75R8422 75R8424 75R9840

580 Super E Backhoe Cummins 4-390 75R8422 75R8424 75R9840

680K Backhoe Cummins 4-390 75R8422 75R8424 75R9840

550G Crawler Cummins 4-390 75R8422 75R8424 75R9840

450C, 455 Crawler Cummins 4-390 75R8422 75R8424 75R9840

860 Trencher Cummins 4-390 75R8422 75R8424 75R9840

W11B Wheel Loader Cummins 4-390 75R8422 75R8424 75R9840

CATERPILLAR216, 226, 228, 236, 246, 248 3034, 3034T 75R8332 75R9960 D17250,

D17475

325, 322, 920, 950E & 966C 3116, 3304, 3306, 3322, 3325 Excavator 75R8384 75R9970 G7380

824C, 825C, 326C, 245, 245B & 980C 3406 75R8384 75R9535 G9600,

G9690

768C, 769C, 772B & 773B 3408, 3412 75R8384 75R9615 G9480

950F 31,143,116 75R8384 75R9635 G9710

215, 225, 229 Excavator 3304 75R8422 75R8424 75R9973 D17501

225, EL 240 Excavator 3304 75R8422 75R8424 75R9815

515, 518, 528, 530B Skid Steer 3304 & 3306 75R8422

75R8424 75R9815

615 Scraper 3306 75R8422 75R8424 75R9815

627B, 627E, with Low Crank Driven Alternator 3306 75R8422

75R8424 75R9815

631D, 631E Scraper 3408 75R8422 75R8424 75R9565

633C Scraper D343 75R8422 75R8424 75R9810

633E, 651E Scraper 3408 & 3412 75R8422 75R8424 75R9565

637A , 637D Scraper 3408 75R8422 75R9565

769C Haul Truck 3408 75R8422 75R8424 75R9565

814, 815, 816 Compactor 3306 75R8422

75R8424 75R9973 D17500, GY17501

Page 13: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 408

75R SERIES

** For R12 installations use 75R5611 and 75R5618 Service Valves† G = Gates D = Dayco GY = Goodyear

COMPRESSOR MOUNT KIT & CLUTCH APPLICATION

Manufacturer Year Engine Clutch R-134a Compressor

R-134a Charge Fitting

Compressor Mount Kit Number Belt No.†

CATERPILLAR814B, 815B, 816B Compactor 3306 75R8422

75R8424 75R9973 D17500, GY17501

824C, 825C Compactor 3406 75R8422 75R8424 75R9565

920, 930, 950, 966C Wheel Loader 3304 & 3306 75R8422

75R8424 75R9973 D17500, GY17501

920, 930, 980B Wheel Loader 3304 & 3306 75R8422

75R8424 75R9973 D17500, GY17501

951C Crawler Loader 3304 75R8422 75R8424 75R9973 D17500,

GY17501

955, 977L Crawler Loader 3304 & 3306 75R8422 75R9973 D17500

988B, 988C, 992C Wheel Loader 3408 & 3412 75R8422

75R8424 75R9565

D22B, D25C, D250B, D35C, D300B, D330B, D350B, D350C

3306 75R8422 75R8424 75R9820

D4E, D6D, Crawler 3304 & 3306 75R8422 75R8424 75R9973 D17500

D5C Series III Crawler 3046 75R8422 75R8424 75R9865

D6C, D5B Crawler 3306 75R8422 75R8424 75R9973 D17500

D6D Crawler with Scroll injector 3306 75R8422

75R8424 75R9815

D6H Crawler 3306 75R8422 75R8424 75R9815

CHAMPION 740 Motor Grader Cummins 855 75R9870DIAMOND REOConventional or C.O.E. Cab 1975-89 Detroit Diesel 6V or 8V-92 75R1202 75R7280 75R5681**

75R5688** 75R9060

DRESSER

TD 20G, TD 25G, TD 40 Cummins 1150 75R8372 75R8374 75R9835

568, 560B Wheel Loader Cummins 1150 75R8372

75R8374 75R9835

558 Wheel Loader Cummins 855 75R8422 75R8424 75R9870

EUCLID

R-25, R-35 Haul Truck Cummins 855 75R8422 75R8424 75R9870

FMC

LS 7400 Excavator Cummins 1150 75R8372 75R8374 75R9835

Page 14: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 409

75R SERIES

** For R12 installations use 75R5611 and 75R5618 Service Valves† G = Gates D = Dayco GY = Goodyear

COMPRESSOR MOUNT KIT & CLUTCH APPLICATION

Manufacturer Year Engine Clutch R-134a Compressor

R-134a Charge Fitting

Compressor Mount Kit Number Belt No.†

FORDL Models CL-9500 1997 - Cummins M-11 75R8382 75R9550

L Models CL-9500 1997 - CAT C-10 75R8382 75R9560

L Models CL-9000 1972-89 Cummins “N” Series Full Flow Cooling Accessories Drive Pulley 210947 or 210948. Except 20 tilt 75R7280 75R5681**

75R5688** 75R9220

1966-89 Cummins “N” 75R8382 75R9670

L Models 1970-92 Cat 3208 V636 with Bracket Mounted Fan 75R8382 75R9900 G9360

CL-9000 1967-89 Detroit Diesel 6V or 8V-71 75R1202 75R7280 75R5681** 75R5688** 75R9060 G9375

GALION

118C Motor Grader Cummins 855 75R8422 75R8424 75R9870

GMC/CHEVROLET See WHITEGMC for information on Astro, Brigadier and General.

H, J, & M Series 1971-89 Detroit Diesel 6V or 8V-71 75R1202 75R7280 75R5681** 75R5688** 75R9060 G9375

GMC COE H, J, & M Series 1969-93 Cummins “N” Series 75R7280 75R5681**

75R5688** 75R9220

GMC/CHEVROLET See WHITEGMC for information on Astro, Brigadier and General.

Titan Series COE H, J, & M Series 1969-93 Cummins “N” Series 75R7280 75R5681**

75R5688** 75R9220

HITACHI

UH801 Excavator Cummins 1150 75R8372 75R8374 75R9835

INTERNATIONAL / NAVISTARS Series 1983-89 V/8 International 6.9 Liter, 421 cu. in. 75R8382 75R9530 G9750

“F”, “S” Series (All) 1979-87 6 Cylinder IHC DT-466 75R1202, 75R7280 75R5681** 75R5688** 75R9100 G9550

2200-2500. 2600 1979-90 75R8382 75R9980 G9420

1994-00 DT-408/DT-466 75R8382 75R9985

S Series 2200-2500 F Series 2200-2500 & 2600

1983-94 Cummins 6 Cylinder L-10 75R8382 75R9540 G9560

Fleetstar “A” & Paystar Series Conventional 1972-89 Cummins “N” Series Full Flow Cooling Accesories except

20° tilt 75R7280 75R5681** 75R5688** 75R9220

4070A Transtar 1969-89 Cummins “N” Series 75R7280 75R5681** 75R5688** 75R9220

JOHN DEERE444H 4045T 75R8354 75R9400 G9505

490E 4045T 75R8354 75R9715

544H 75R9405

544/624 6059T, 6-414, 4039D, 4239D, 4045D, 4045T75R8384 75R8374 75R8374

75R9585, 75R9645

G9520, G9390

624H 75R9410

690E/790E 6068T 75R8384 75R9710 G9476

744E/992E,D 6101A/6101AT 75R8384 75R9805 G9440

Page 15: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 410

75R SERIES

** For R12 installations use 75R5611 and 75R5618 Service Valves† G = Gates D = Dayco GY = Goodyear

COMPRESSOR MOUNT KIT & CLUTCH APPLICATION

Manufacturer Year Engine Clutch R-134a Compressor

R-134a Charge Fitting

Compressor Mount Kit Number Belt No.†

KENWORTH

CONV & COE 1966-89 Cummins Series, High Fan. Full Flow Cooling except 20° tilt 75R7280 75R5681** 75R5688** 75R9220

1966-89 Cummins “N” 75R8382 75R9670

CONV & COE 1966-89 Detroit Diesel 6V or 8V-71, 6V or 8V-92 75R1202 75R7280 75R5681** 75R5688** 75R9060 G9375

SK400 M.D. 1995- Cummins M11 75R8384 75R9630 G9412KOMATSUWA500 Wheel Loader SA6D140 75R8384 75R9595 G9335

WS 23S-1 Scraper Cummins 1150 75R8372 75R8374 75R9835

PC 400LC5 Excavator S6D125-1 75R8422 75R8424 75R9845

WA470, WA450-1L Wheel Loader S6D125 75R8422

75R8424 75R9845

WA450-3 Wheel Loader SA6D125E-2 75R8422

75R8424 75R9845

PC180 Excavator S6D95L 75R8422 75R8424 75R9850

WA120, WA150 Wheel Loader S6D95L-1 75R8422

75R8424 75R9850

WA180 Wheel Loader S6D95L 75R8422 75R8424 75R9850

D41P-6 Crawler S6D102E-1 75R8422 75R8424 75R9860

PC150-6 Excavator SA4D102E 75R8422 75R8424 75R9860

WA250-3 Wheel Loader S6D102E-1 75R8422 75R8424 75R9860

WA500 Wheel Loader Cummins 855 75R8422 75R8424 75R9870

PC400LC5 Excavator Cummins L-10 75R8422 75R8424 75R9875

WA 450-3 Wheel Loader Cummins LTA-10 75R8422 75R8424 75R9875

LIEBHERR962, 972, 974, 982 Excavator Cummins 855 75R8422

75R8424 75R9870

MACK

R Models 1972-87 6 Cylinder Mack 675, 676 & 685 END-T, with or without Turbocharger 75R8382 75R9500 G9400

R, “U” & “DM” Models 1972-89

6 Cylinder Mack 675, 676 & 685 END-T, with or without Turbocharger, 2 or 4 Valve Head with United Technology or Bosch 6000 Fuel Injector System & Cast Aluminum Timing Cover

75R8382 75R9500 G9400

R “U” & “CM” Models 1987-89

6 Cylinder Mack 675, 676 & 685 END-T, with or without Turbocharger 2 or 4 Valve Head with United Technology or Bosch 6000 Fuel Injection System & Cast Aluminum Timing Cover

75R8382 75R9730 G9400

Page 16: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 411

75R SERIES

** For R12 installations use 75R5611 and 75R5618 Service Valves† G = Gates D = Dayco GY = Goodyear

COMPRESSOR MOUNT KIT & CLUTCH APPLICATION

Manufacturer Year Engine Clutch R-134a Compressor

R-134a Charge Fitting

Compressor Mount Kit Number Belt No.†

MACK

R “U” & “DM” Models 1966-89 Cummins “N” Series except NTC-290 & 350 Accessories Drive Pulley 209669 or 190496 except 20° tilt 75R2702 75R7280 75R5681**

75R5688** 75R9220

1966-89 Cummins “N” 75R8382 75R9670

F Model COE 1965-89 Cummins NTC-290 & 350 except 20° tilt 75R7280 75R5681** 75R5688** 75R9220

F Model COE 1966-89 Cylinder 335 Turbocharged except NTC-290 & 350. Except 20° tilt 75R7280 75R5681**

75R5688** 75R9220

E6 Serial #T396BR192 and E7 All 75R8382 75R9515 G9495

MS 200, 250, 300 1983- Non California Engine (60212) 75R8382 75R9920

G7530, G7470, G9470, G9490

MANITOWOC888 Crane Mobile Truck Crane Cummins L-10 75R8422

75R8424 75R9830

3900 Crane Mobile Truck Crane Cummins L-10 75R8422

75R8424 75R9830

M-250, 3900, 4100 Crane Cummins N14 75R8422

75R8424 75R9870

MARMONHDT COE & 1967-89 Cummins “N” Series 75R7280 75R5681** 75R9000

HDT & “CHDT” 1977-89 Detroit Diesel 8V-92 75R1202 75R7280 75R5681** 75R5688** 75R9060 G9375

PETERBILTConventional & COE Series 1973-89 Cummins “N” Series Accessory Drive Pulley 208831 except

20° tilt. 75R7280 75R5681** 75R5688** 75R9220

Conventional & COE Cab 1963-89 Detroit Diesel 6V or 8V-71 75R1202 75R7280 75R5681** 75R5688** 75R9060 G9375

TEREX

3308 Haul Truck Cummins KTTA19C 75R8372 75R8374 75R9835

S24C Scraper Cummins 1150 75R8372 75R8374 75R9835

WESTERN STAR

Conventional 1967-89 Cummins “N” Series Full Flow Cooling except 20° tilt 75R7280 75R5681** 75R5688** 75R9220

1966-89 Cummins “N” 75R8382 75R9670WHITE GMC

Road Commander COE 1966-89 Cummins “N” Series. Full Flow Cooling, NH-250 & NTC-335. Accessory Drive Pulley 211005 or 190546 except 20° tilt 75R2702 75R7280 75R5681**

75R5688** 75R9220

1966-89 Cummins “N” 75R8382 75R9670

4000 & 9000 Road Boss 1967-89 Cummins “N” Series Full Flow Cooling except 20° tilt 75R7280 75R5681** 75R5688** 75R9220

1966-89 Cummins “N” 75R8382 75R9670

6000 Series Expeditor COE 1972-89 Cummins “N” Series Full Flow Cooling except 20° tilt 75R7280 75R5681**

75R5688** 75R9220

1966-89 Cummins “N” 75R8382 75R9670

Page 17: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 412

75R SERIES

** For R12 installations use 75R5611 and 75R5618 Service Valves† G = Gates D = Dayco GY = Goodyear

COMPRESSOR MOUNT KIT & CLUTCH APPLICATION

Manufacturer Year Engine Clutch R-134a Compressor

R-134a Charge Fitting

Compressor Mount Kit Number Belt No.†

WHITE GMC

Bruin or Brigadier 1979-89 Detroit Dsl. 6V/8V-71 with Hydraulic Clutch Fan Only 75R1202 75R7280 75R5681** 75R5688** 75R9060

H, J, & M Series Titan Series & Astro Series 1969-89 Cummins “N” Series with Standard or Full Flow Cooling.

Except 20° tilt 75R7280 75R5681** 75R5688** 75R9220

1966-89 Cummins “N” 75R8382 75R9670

Titan & Bison Brigadier, Bruin 1977-89 Detroit Diesel 6V or 8V without Hydraulic Fan 75R1202 75R7280 75R5681**

75R5688** 75R9060

Page 18: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 413

75R SERIES COMPRESSOR ACCESSORIES

COMPRESSOR SERVICE PARTS

75R5200 RD-5-8334-0MCCI And Tecumseh Keyway — 10 Per Package

75R5201 RD-5-9979-0MSanden Shaft Key 508 ⁄ 510 ⁄ 709 — 10 Per Package

75R5520 RD-5-3698-0MTeflon Rotolock Compressor Gasket Seal 10 Per Package IHC/Navistar ZGG19499

75R5525 RD-5-9806-0MO-Ring Seal fits Sanden FLX7 fitting adapters GM A6 DAG, HR6, R4, R5 compressor Suction/Discharge Port O-Ring 10 Per Package

75R5540 RD-5-5401-0MPlastic Schrader Port Cap — 10 Per Package 3 ⁄16” charging port

75R5555 RD-5-11325-0ME-Z Clip Low Side Cap 20 Per Package

75R5556 RD-5-11223-0ME-Z Clip High Side Cap 20 Per Package

75R5560 RD-5-7523-0M13mm Low Side Service–Black – 25 Per Package valve cap with neoprene seal; OE & aftermarket type R-134a ports

75R5565 RD-5-8293-0M13mm Low Side High Flow Valve Cap with neoprene seal–Blue, R-134a port — 10 Per Package

75R5570 RD-5-7524-0M16mm High Side Service Flow Valve Cap with neoprene seal – Black – 10 Per Package

75R5575 RD-5-8292-0M16mm High Side High Flow Valve Cap with neoprene seal – Red – R-134a Eaton OEM SSV 10 Per Package

75R5700 RD-5-4997-0MAdapter converts Rotolock To Tube O-Ring 2 Per Package

75R5705 RD-5-9812-0PConverts Tube O-Ring To Rotolock atapter

79R4597 RD-5-11568-0PSanden Oil Dip Stick

= Limited to stock on hand

SCHRADER ADAPTER FITTINGS

70R5100 RD-5-6098-0M3⁄8-24 UNF-2A Male Thread with Bulkhead Type Seal Using a 2-012 O-Ring for Installation in Receiver Drier Pressure Ports 10 per package

70R5110 RD-5-6691-0MRefrigeration Valve Core for Schrader Valves 10 per package

70R5115 RD-5-9084-0MValve Core for 134A Fittings – High Flow 10 per package

70R5120 RD-5-9809-0MEaton 13mm SSV High Flow-High Side 10 per package

70R5125 RD-5-9810-0MEaton 16mm SSV High Flow-Low Side 10 per package

79R8945 RD-5-12674-0PHigh Flow Schrader Valve Core Remover/Installer Tool

Page 19: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 414

75R SERIES COMPRESSOR ACCESSORIES

75R5878S RD-5-8402-0P#8 Straight Female Tube-O with 134a Port Fits Sanden “M” Heads

75R5718 RD-5-5396-0P#8 O-Ring to 1” x 14 O-Ring w⁄ith Schrader port

COMPRESSOR O-RING FITTING USED ON SANDEN ONLY WITH “C” OR “M” HEAD

HD RETROFIT ADAPTER KIT79R8940 RD-5-9986-0P

IN-LINE SERVICE PORT75R5806 RD-5-7306-0P #675R5808 RD-5-7539-0P #875R5801 RD-5-7310-0P #10 STEEL HIGHSIDE CHARGE ADAPTER

All include valve core, neoprene O-ring and threadlock75R5825 RD-5-9816-0P 13mm

1⁄4” (7⁄16 - 20) Threads Blue Cap – Low Side

75R5824 RD-5-9815-0P 16mm 1⁄4” (7⁄16 - 20) Threads Red Cap – High Side

CHARGE ADAPTER KIT WITH SCHRADER INSERT75R5815 RD-5-7964-0P

CHARGE FITTINGS75R5813 RD-5-7277-0M Lowside 134a Fitting

75R5814 RD-5-7278-0M Highside 134a Fitting (for use on hard lines)

75R5833 RD-5-9218-0M Lowside 134a Fitting

75R5834 RD-5-9219-0M Highside 134a Fitting (for use on hard lines)

90˚ CHARGE ADAPTERSAll include valve core, neoprene O-ring and threadlock75R5819 RD-5-8850-0P Lowside 90°

134A Charge Adapter with 1⁄4 (7⁄16-20) Thread 13mm, Blue Cap

75R5820 RD-5-8851-0P Highside 90° 134A Charge Adapter with 1⁄4 (7⁄16-20) Thread Red Cap

90° GM SERVICE FITTING WITH PORT75R5858 RD-5-7438-0P #8 75R5852 RD-5-7488-0P #12

90° COMPRESSOR PORT REVERSED 75R5832 RD-5-7489-0P #12

ST GM SERVICE FITTING WITH PORT 75R5842 RD-5-7487-0P #12

SERVICE PORTS AND ADAPTERS

= Limited to stock on hand

Page 20: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 415

75R SERIES COMPRESSOR ACCESSORIES

COMPRESSOR SERVICE FITTINGSHose End Hose End Port Red Dot Red Dot Fitting Type Fitting Size Valve Type Description / Location Part No. Factory No.

ROTOLOCK HEAD Port Charge Type - R-134a O-Ring 8 3⁄4” Backseat 16mm (Hi Side) 75R5698 RD-5-9813-0PO-Ring 8 3⁄4” Service Fitting - 75R5668 RD-5-7318-0PO-Ring 8 3⁄4” Service Fitting 16mm (Hi Side) 75R5688 RD-5-7966-0PBeadlock 8 3⁄4” Service Fitting 16mm (Hi Side), Top 75R5728 RD-5-9952-0PO-Ring 10 7⁄8” Backseat 13mm (Lo Side) 75R5691 RD-5-9814-0PO-Ring 10 7⁄8” Service Fitting - 75R5661 RD-5-7320-0PO-Ring 10 7⁄8” Service Fitting 13mm (Lo Side) 75R5681 RD-5-7967-0PBeadlock 10 7⁄8” Service Fitting 13mm (Lo Side), Top 75R5721 RD-5-9953-0PBeadlock 12 1 1⁄16” Service Fitting 13mm (Lo Side) 75R5722 RD-5-9955-0P

TUBE O-RING Port Charge Type - R-134a O-Ring 8 3⁄4” Backseat 16mm (Hi Side) 75R5738 RD-5-9910-0PO-Ring 8 3⁄4” Service Fitting 16mm (Hi Side) 75R5648 RD-5-7613-0PBeadlock 8 3⁄4” Service Fitting 16mm (Hi Side) 75R5678 RD-5-7430-0PO-Ring 8 3⁄4” Service Fitting 16mm (Hi Side) 75R5808 RD-5-7539-0PO-Ring 8 3⁄4” Service Fitting 16mm (Hi Side) 75R5768 RD-5-7688-0PO-Ring 10 7⁄8” Backseat 13mm (Lo Side) 75R5731 RD-5-9956-0PO-Ring 10 7⁄8” Service Fitting 13mm (Lo Side) 75R5641 RD-5-7614-0PBeadlock 10 7⁄8” Service Fitting 13mm (Lo Side) 75R5671 RD-5-7456-0PO-Ring 10 7⁄8” Service Fitting 13mm (Lo Side) 75R5761 RD-5-7690-0PO-Ring 10 7⁄8” Service Fitting 13mm (Lo Side) 75R5801 RD-5-7310-0PBeadlock 12 1 1⁄16” Service Fitting 13mm (Lo Side) 75R5672 RD-5-7480-0PPort Charge Type - R-12 O-Ring 8 3⁄4” Backseat 1⁄4” (7⁄16 -20), Top 75R5658 RD-5-5197-0PO-Ring 8 3⁄4” Service Fitting 1⁄4” (7⁄16 -20) 75R5718 RD-5-5396-0PO-Ring 10 7⁄8” Backseat 1⁄4” (7⁄16 -20) 75R5651 RD-5-5198-0P

75R5641 RD-5-7614-0P#10 Tube-O Compressor Fitting O-Ring Type Fitting R-134a

75R5648 RD-5-7613-0P#8 Tube-O Compressor Fitting O-Ring Type Fitting R-134a

75R5651 RD-5-5198-0P#10 Tube-O Compressor Fitting O-Ring Type Fitting Backseat Valve Type R-12

75R5658 RD-5-5197-0PTube-O Compressor Fitting #8 O-Ring Type Fitting Backseat Valve Type R-12

75R5661 RD-5-7320-0PRotolock Compressor Fitting #10 O-Ring Type Fitting R-134a

75R5668 RD-5-7318-0PRotolock Compressor Fitting #8 O-Ring Type Fitting R-134a

75R5671 RD-5-7456-0PTube-O Compressor Fitting #10 O-Ring Type Fitting R-134a

75R5672 RD-5-7480-0PTube-O Compressor Fitting #12 Hose Fitting Service Fitting Valve

75R5678 RD-5-7430-0PTube-O Compressor Fitting #8 Hose Fitting R-134a

= Limited to stock on hand

Page 21: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 416

75R SERIES COMPRESSOR ACCESSORIES

COMPRESSOR SERVICE FITTINGS75R5681 * RD-5-7967-0P

Rotolock Compressor Fitting #10 Hose Fitting R-134a

75R5688 * RD-5-7966-0PRotolock Compressor Fitting #8 O-Ring Type Fitting R-134a

75R5691 RD-5-9814-0PRotolock Compressor Fitting #10 O-Ring Type Fitting Backseat Valve Type 13mm, 7⁄8”-14 thread R-134a

75R5698 RD-5-9813-0PRotolock Compressor Fitting #8 O-Ring Type Fitting Backseat Valve Type 16mm, 3⁄4”-16 thread R-134a

75R5718 * RD-5-5396-0P

#8 Tube-O to 1" X 14 O-Ring with Schrader Port R-12

75R5721 RD-5-9953-0PRotolock Compressor Fitting #10 Hose Fitting R-134a

75R5722 RD-5-9955-0PRotolock Compressor Fitting #12 Hose Fitting R-134a

75R5728 RD-5-9952-0PRotolock Compressor Fitting #8 Hose Fitting R-134a

75R5731 RD-5-9956-0PTube-O Compressor Fitting #10 O-Ring Type Fitting Backseat Valve Type R-134a

75R5738 RD-5-9910-0PTube-O Compressor Fitting #8 O-Ring Type Fitting Backseat Valve Type R-134a

75R5761 RD-5-7690-0P#10 Tube-O Compressor Fitting O-Ring Type Fitting R-134a Converts Tube-O to Male Insert O-Ring

75R5768 RD-5-7688-0P#8 Tube-O Compressor Fitting O-Ring Type Fitting R-134a Converts Tube-O to Male Insert O-Ring

75R5801 RD-5-7310-0P#10 Female (Long Pilot) O-Ring to #10 Male Insert O-Ring Type Fitting With R-134a Service Port

75R5808 RD-5-7539-0P#8 Female (Long Pilot) O-Ring to #8 Male Insert O-Ring Type Fitting With R-134a Service Port

= Limited to stock on hand

Page 22: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 417

75R SERIES COMPRESSOR ACCESSORIES

COMPRESSOR ADAPTER BRACKETS

Brackets useful in designing mounts for unique engine applications

75R6020 RD-9-1048-0PCCI/Tecumseh

75R6030 RD-9-1049-0PSanden

75R6040 RD-5-6547-0PBelt Tensioner Pulley Kit Diameter 3 3⁄8” Belt Size: 1⁄2”

75R6041 RD-5-6415-0PBelt Idler Pulley Kit Diameter 3 3⁄8” Belt Size: 1⁄2”

SANDEN COMPRESSOR ADAPTER BRACKETS

75R6000 RD-5-5031-0PFixed compressor adapter bracket will mount Sanden compressor to most Tecumseh or York brackets.

75R6010 RD-5-5032-0PAdjustable compressor adapter bracket to fit Sanden mount holes

75R6015 RD-9-1150-0PCompressor bracket for Sanden Only

75R6016 RD-9-9457-0P3⁄8-16 Compressor Adjuster

75R6017 RD-9-1068-0PAdjusting Arm

75R6018 RD-9-9910-0PRam Horn

= Limited to stock on hand

Page 23: (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES...BLISSFIELD (TECUMSEH), TCCI (YORK) COMPRESSOR CLUTCHES = Limited to stock on hand If part number on clutch being replaced cannot be read

PAGE 418

75R SERIES COMPRESSOR ACCESSORIES

TECUMSEH/YORK/CCI SHAFT SEAL KITS

75R6500 RD-5-8339-0PCCI And Tecumseh Shaft Seal Kit 6 Bolts-3⁄8” Head

75R6510 RD-5-8338-0PCCI Shaft Seal Kit 6 Bolts-1⁄4” Head

4 1

5 6

2 3

6 Bolt – 1⁄4” Heads

1⁄4”

6 Bolt – 3⁄8” Heads

3⁄8”

ZEXEL/SANDEN SHAFT SEAL KITS

75R6530 RD-5-8340-0PZexel (Diesel Kiki)

75R6540 RD-5-8335-0PSanden SD508-SD510

75R6545 RD-5-7704-0PSanden 7H15, 7H15HD

75R6550 RD-5-8336-0PSanden SD709

= Limited to stock on hand