technical manual resound match cicgto.gnresound.com/service/gnresound/match/0175800... · doc. no....

Technical ManualReSound Match CIC

GN ReSound asGlobal Technical Operations

Lautrupbjerg 7 • DK-2750 Ballerup • DenmarkE-Mail: [email protected]

Doc. No. 0175800 rev. D

of 16

Table of contents

Subject Page

Matrix ............................................................................................................. 3 Spare Part List ............................................................................................... 4 Faceplate Assemblies .................................................................................... 5 Hybrid Connections ........................................................................................ 6 PCB & Trimmer Connections ......................................................................... 7 Wiring Diagram ........................................................................................... 8-9 Receiver assembly ....................................................................................... 10 Microphone assembly ...................................................................................11 Prepare the faceplate ................................................................................. 12 Options ......................................................................................................... 13 FP final assembly ......................................................................................... 14 Service tool .................................................................................................. 15 Test Equipment ............................................................................................ 16

Doc. No. 0175800 rev. D

of 16

Matrix

C3.1 Battery Size 10

Normal Power Single Mic

VC(G-Trimmer)

L - Trimmer Push Button Telecoil

MA10-P x x x Optional Optional Not Optional Not OptionalMA1T10-P x x x Standard Optional Not Optional Not OptionalMA2T10-P x x x Standard Standard Not Optional Not Optional

Note: • Only one trimmer can be added for the CIC Model in combination with the G-Trimmer. The Trimmer choices are L-Trimmer, H-Trimmer and P-Trimmer.• If a trimmer is opted to be added / removed, the device must be reconfigured in the AUDIOMaster or the Match Configuration Tool software to reflect correct option added / removed.• The Match Configuration Software can be downloaded from the GTO website: http://gto.gnresound.com

Doc. No. 0175800 rev. D

of 16

Spare Part list Item Part No.Tape, 3m., Doubleface (3 mm.) 10038902Tape, 3m., Doubleface (56X3.9MM) 10038905Tubing, Q-flex (rec.) 10049101Tubing, Silicone uncut 11509-000Kapton Tape 1.3 mm.x9 mm. 13006-003FLEX-HYBRID, C3.1 16016900Microphone, EM-6611, 9167 15069002Receiver, FH-6719 HP 15198000Trimmer,G,150K,PJ63, Red 16809200Trimmer,L,150K,PJ63, Green 16667500Trimmer,H,150K,PJ63, Yellow 16667600Trimmer,P,150K,PJ63, Black 16667700PCB,SUB,ASM,NEWTRIM,TRIMMER 16693100Sleeve, Wire 11834-001Wire, ESW, Blue, 7x50µ 16 mm. 15130316Wire, ESW, Blue, 7x50µ 18 mm. 15130318Wire, ESW, Green, 7x50µ 8 mm. 15130208Wire, ESW, Green, 7x50µ 16 mm. 15130216Wire, ESW, Green, 7x50µ 18 mm. 15130218Wire, ESW, Green, 7x50µ 25 mm. 15130025Wire, ESW, Red, 7x50µ 16 mm. 15130016Wire, ESW, Red, 7x50µ 20 mm. 15130020Wire, ESW, Red, 7x50µ 25 mm. 15130025Wire, ESW, Amber, 7x50µ 18 mm. 15130118Wire, ESW, Amber, 7x50µ 20 mm. 15130120

Blank FP, 10A UNIVERSAL Part No.Light 15183000Medium 15183001Dark 15183002

Battery doors, 10A , A Part No.Light 15183110Medium 15183111Dark 15183112

Battery doors, 10A , B Part No.Light 15183120Medium 15183121Dark 15183122

Note: For conformal coating EGC-17000, check the vendor website: www.3M.com to purchase locally. For conformal coating SL1367 peters coat, check the vendor website: www.peters.de to purchase locally.

Doc. No. 0175800 rev. D

of 16

Faceplate Assemblies

NO OPTION 1 TRIMMER OPTION 2 TRIMMER OPTION

Doc. No. 0175800 rev. D

of 16

Hybrid connections (C3.1 Flex)

H12

H11

H10

H13 H14

H17

H21 H22

H16 H15

H1

H2H3

H4

H5H6

H8

H7H9H20

H18 H19

H12

H11

H10

H13 H14

H17

H21 H22

H16 H15

H1

H2H3

H4

H5H6

H8

H7H9H20

H18 H19

MIC +

MIC -

MIC(0)

MODULEMODULE

BATT +

BATT -

REC -

REC +

PCBG-Trim “S”

L-Trim “S”NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering.

Doc. No. 0175800 rev. D

of 16

PCB & Trimmer Connections PCB

GND

Pad H20

G-Trimmer E& Option Trimmer A

G-Trimmer A & Option Trimmer E

E

S

A

Pad H18

PCBPCB

The “S” lead wire colour varies depending on the OptionTrimmer.

G-TRIMMER

E

S

A

OPTION TRIMMER

hybrid

PCB PCB

NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering.

Doc. No. 0175800 rev. D

of 16

Diagram

H20 H 9

SEA

SEA

L -TRIMMER

G -TRIMMER

PCB


Doc. No. 0175800 rev. D

of 16

Diagram


Doc. No. 0175800 rev. D

of 16

Receiver assembly

Solder the wires as shown.

Red wire 25 mm. p/n 15130025Green wire 25 mm. p/n 15130225

Place the Q-flex tubing as shown.Bend the wires. Cut the siliconeTubing to 1.3 mm. and place it overthe wires.

Silicone tubingp/n 11509-000

Q-flex tubingp/n 10049101


Doc. No. 0175800 rev. D

of 16

Microphone assembly

mic replacement comes with wires

+

9768

Standard CIC mic.

Just add sleeve onto the wiresP/N 11834-001


Doc. No. 0175800 rev. D

of 16

Prepare the faceplate - Trimmer Installation

Mark target hole. Drill target hole. Remove debris and insert trimmer,

Make trimmer flush even on the external side of faceplate.

Use Loctite 416 and glue around the trim-mer (internal side). Let it cure.

NOTE : Do the same process for additional trimmers. Let the glue cure first then operate the trimmer to ensure that it is not frozen.

Drill bit 0.076” or 1.93mm for the trimmer hole

Doc. No. 0175800 rev. D

of 16

Trimmer Options

G - TRIMMER

1 TRIMMER DEFAULTOTHER TRIMMER OPTION

E

S

A

Pad 18PCB PCB

Note: If a trimmer is opted to be added / removed, the device must be re-configured in the AUDIOMaster or the MATCH Configuration Tool Software to reflect correct option added / removed. The Match Configuration Soft-ware can be downloaded from the GTO website: http://gto.gnresound.com

P - TRIMMER L - TRIMMERH - TRIMMER

ES

AES

A

Pad 21PCB PCB

Pad 22PCB PCB

Pad 19PCB PCB

ES

A

Doc. No. 0175800 rev. D

of 16

FP Final Assembly

1 TRIMMER OPTION 2 TRIMMER OPTION

Doc. No. 0175800 rev. D

of 16

Service Tool

When working on the assembled faceplate a heat sink (p/n 10158701) must always be used in order to prevent damages to the components.

The tool can be used on both sides. One side for size 13 and 312, the other side to be used for size 10

Size 13 and 312 Size 10

Doc. No. 0175800 rev. D

of 16

Test Equipment

Connect the flex to the programming cable by using the flex end marked with an arrow.• Programming cable CS63 p/n 50931703• Flex strip 10 pcs. p/n 50931703

When testing / programming abattery pill must be used.

Programming cable CS44 :• p/n 9022 907 69029, Blue (L.).• p/n 9022 907 69019, Red (R.).• Flex adaptor CS44 (incl. a flex strip) p/n 9022 907 69579.

Both programming cable sets can be used.

The device is to be configured with either AUDIOMaster or MATCH Configura-tion Software for trimmer change option. The Configuration Software can be downloaded from the GTO website http://gto.gnresound.com

technical manual resound match cicgto.gnresound.com/service/gnresound/match/0175800... · doc. no....

Documents