tb-1900 gsm ds 0-0-3
TRANSCRIPT
-
7/27/2019 TB-1900 GSM DS 0-0-3
1/3
GSM1900M Tower Mounted BoosterTB-1900(40W)
Information contained in this document is subject to confirmation at time of ordering.http://www.comba-telecom.com
Issued: 22Nov10Control: 0-0-1
1/3
Features
High downlink power 46dBm for extended cell coverage.
MCPA with 20MHz Instantaneous Bandwidth can support multiple GSM Downlink carriers.
Low noise amplifier reduces uplink system noise figure and helps to reduce call drop and improve voice quality.
Reduces handset output power to improve uplink C/I.
Permits local or remote monitoring via PC or wireless modem.
Alarms can be transmitted to OMC via data link or SMS.
External alarm to BTS by voltage-free relay contacts.
Automatic RF by-pass feature permits BTS operation when equipment or power supply fails.
Internal Li-ion backup battery ensures alarm messages are transmitted when equipment or power supply fails.
Designed for all outdoor application waterproof, damp-proof and omni-sealed (IP65).
Product Description
The TB-1900 is a GSM tower mounted booster (TMB) that provides both uplink and downlink amplification. The TMB unitis installed near the antenna at the tower top to boost the transmitted power for extended cell coverage. The uplink
low-noise amplifier (LNA) serves to improve the sensitivity of the BTS to cope with the extended cell coverage in the
downlink.
The TB-1900 is powered through a separate power cable, with various power supply options. The system consists of
duplexers, uplink LNA, downlink MCPA, RF by-pass switch, main control unit (MCU), distribution board, power supply unit,surge protector, wireless modem, and Li-ion backup battery. Parameter settings of the unit can be done locally via a PC
with OMT, or remotely via wireless modem using OMT or OMC software. Alarms are displayed on the OMT screen and could
be detected by BTS as external alarm. Through the wireless modem, the alarm data can be transmitted to the OMC
automatically, or be sent as SMS to a predefined cellular device.
Functional Block Diagram
Ant1
ServiceAntenna
1Tx1Rx1
BTS1
Downlink/UplinkBy-pass
LNA1
MCPA
UplinkBy-pass
Rx1Diversity
B
T
S
BTS2Ant2
ServiceAntenna
2
LNA2
-
7/27/2019 TB-1900 GSM DS 0-0-3
2/3
GSM1900M Tower Mounted BoosterTB-1900(40W)
Information contained in this document is subject to confirmation at time of ordering.http://www.comba-telecom.com
Issued: 22Nov10Control: 0-0-1
2/3
Technical Specifications
ElectricalFrequency Range, Uplink MHz 1850 1910
Frequency Range, Downlink MHz 1930 1990Instantaneous Bandwidth MHz 20
Intermodulation, Downlink dBc -60
Total Output Power dBm 46
Output Power Fluctuation dB 1
Maximum Uplink Gain dB 12 1
Maximum Downlink Gain dB 20 1
Gain Adjustment Range (1dB Step), Uplink dB 0 - 12
Gain Adjustment Range (1dB Step), Downlink dB 0 20
9kHz to 1GHz dBm -36 / 100KHzSpurious
1GHz to 12.75GHz dBm -30 / 1MHz
Noise Figure, Uplink dB 3.0
Absolute Maximum RF Output Power Uplink dBm +10
Absolute Maximum RF Input Power Downlink dBm +43
Insertion Loss, By-pass Mode dB 2.0
Pass Band Ripple, p-p dB 2.0
System Group Delay nsec 500
Input VSWR 1.5
Impedance 50
Power, Mechanical & EnvironmentalDimensions, H x W x D mm TBD
Weight (approx.) kg 37
VAC 90 264 / 47 63HzPower Supply
VDC -48
AC Power Consumption (approx.) W 600
Power Up Waiting Time (approx.) sec 60
MCU Battery Backup Time (approx.) hr 3
Enclosure Cooling Fan
RF Connectors N-F or 7/16 Din-FOperating Temperature C -40 to +55
Operating Humidity % 95
Environmental Class IP65
MTBF hr > 50,000
Note: Typical specifications at room temperature.*1: f deviation from the center of GSM allocated carrier.
-
7/27/2019 TB-1900 GSM DS 0-0-3
3/3
GSM1900M Tower Mounted BoosterTB-1900(40W)
Information contained in this document is subject to confirmation at time of ordering.http://www.comba-telecom.com
Issued: 22Nov10Control: 0-0-1
3/3
Operation and Maintenance
Using a direct serial connection to a PC, installation and commissioning of the TB-1900 is accomplished by the OMT at the
bottom PCU. Using the integrated wireless modem (data or SMS mode), equipment parameters can be monitored and
controlled remotely.
Controlled equipment parameters include: Channel No, UL/DL ATT, Soft ON/OFF, Over-Temp Threshold, DL Output Power
Threshold, DL Input Power Threshold and Alarm Report Enable.
Monitored equipment alarms and parameters include: Alarms (LNA, DL PA, Power Down, PSU Fault, Door Open, DL Input
Power Low, DL Output Power Low, Over Temp), UL/DL Gain, DL Input /Output Power.
The TB-1900 has been developed to take advantage of advanced network operation, where the OMC (optional) provides an
effective solution for central monitoring of a group of Comba products.