table of contents - scientific.net · high-performance sensorless control of pmsm based on sliding...
TRANSCRIPT
Table of Contents
Preface and Organizing Committee
Chapter 1: Computer-Aided Manufacturing
Automatic On-Line Detection and Sorting System Design and Implementation for Paper-Making PrintingR.X. Sun, L. Gao, J. Kang, P.P. Huang, Y. Tian and X.F. Chen 3
Design and Realization of Monitoring System for Multiway pH ValueR.X. Sun, P.P. Huang, N. Ran, J. Kang, X.F. Chen and Y. Tian 6
The CAD/CAM of Hydraulic Valve Block Based on Pro/EngineerW.L. Wu, X.J. Jin and K.L. Xing 12
Design and Implementation of a Computer Vision Based Inspection System Using CUDAY. Shi, A.G. Li and L. Wang 18
Structure Reverse Design and CFD Analysis on Agitated Flow Field of Submersible MixerW.X. Xu and M.Y. Fan 25
Robust State-Feedback Controller Design for Uncertainty Singular SystemsL.M. Liang, F.L. Weng and Y.C. Ding 32
An Estimation Approach Based on Predictive Filtering to Missile GuidanceY.Y. Song, W.C. Chen and X.L. Yin 38
Controller Design for Spinning Missile with the Actuator LimitF. Liu and W.C. Chen 45
The Time-Delay Study on Vehicle Active Control SuspensionF.R. Kou 52
The Research on High-Voltage Transmission Line Relay Protection Setting Related toOLTC Anti-IcingS.Q. Liu, H. Wang, X.M. Li and D.X. Zhou 59
Development of Islanding Detection Based on Power Controlling for Grid-Connected ofDispersed Power GenerationW.M. Chen, G.C. Chen and H. Cai 66
The Stabilization of Singular Linear Large-Scale Control Systems with Output FeedbacksC.T. Chen and J.L. Ding 72
Multimode Adaptive Control for Tank Gun Control System Based on TrackingDifferentiatorD. Yuan, X.J. Ma and W. Wei 79
Optimization of PMSM Sensorless Control Based on Improved PSO AlgorithmM.W. Qian, G.J. Tan, N.N. Li and Z.X. Zhao 86
Design of PID Algorithm Control System Based on DSPC.J. Zhong and Z.A. Guan 93
The Suspension System Design for the Tensioner of the Ocean Pipeline BargeZ.P. Guo, C. Zhang, B.Z. Li, L.L. Wang and S.M. Zhang 98
Durability Test System of Four-Channel Motorcycle Wheel Speed Sensor Based onLabVIEWJ.M. Tian and J.J. Liang 104
Improved CMAC Neural Network Control for Superheated Steam TemperatureL.J. Chen, B. Sun, J.C. Diao and L.L. Zhao 111
Researches on Start Control Strategy of CNG EngineC.Q. Ni and Y.T. Zhang 118
Design of Embedded CNC Device Based on ARM and FPGAM. Zhou 125
Study on Floating Raft Vibration Isolation System for Pumping UnitF.M. Wang, C.G. Wang, L.L. Guo, B.C. Wen and Y. Li 130
Distributed Flexible Strip-Type Soil Moisture Sensing and Detection SystemG. Shi and Q. Li 136
Design of Artificial Climate Chamber Control System for Food Crops Cultivation Based onExpert Knowledge BaseZ.H. Li and G. Liu 145
Research on the Identification of Tubular-Furnace Based on CARIMA ModelZ.P. Chen, X.J. Li and E.Z. Dong 151
Development and Design of Dance Robot Based on Single-Chip Microcomputer AT90S8535Y.M. Han 157
Study on Sliding Mode Control with Gray Theory for Electro-Hydraulic Servo SystemQ. Zhang, L. Hou, Y. Tang and S. Liu 163
Research on FFU Power Supply Based on Variable Universe Adaptive Fuzzy ControlY.W. Wang 170
Calibration System Development of Electronically Controlled Engine Based on CCPL. Tang, L. Xie, M.W. Wang and H.Y. Gan 175
Analysis for Obstacle Negotiation Capability of Wheel-Legged RobotH.B. Tian, Z.D. Fang, F.J. Meng and X.F. Yang 183
Research on the Singularity and Stationarity of 3-TPT Parallel Machine ToolH.H. Zhao and C.Q. Wang 190
Speed Sensor-Less Indirect Vector Control System Based on a Novel Sliding Mode ControlSpeed ObserverG.H. Li and J.Q. Wang 196
Research on a New Automatic Instrument Transformer CalibratorC.Y. Xu and L. Ye 202
Cascade Fuzzy Self-Tuning PID Control for the Liquid-Level Control of Double Water-TankY. Lin and X.L. Ye 207
Design of Real-Time Monitoring System for Surface Water Pollution Based on GPRSG.J. Chen and J.L. Jia 213
Experiment on Ultimate Shear Strength Parameters of Bolt Anchored SectionS.C. Gu and G.F. Ye 218
Application of Embedded Technology for Induced Polarization InstrumentQ.S. Zhang, M. Deng, Q. Wang, Y.Q. Feng and R. Yang 224
Alleviate Stressful Voltage Condition of Power System by Means of Adjusting theGeneration Mode Considering Energy SavingG.F. Qiu and H.C. Shu 230
Design of Double Closed Loop Control System of Automatic ClutchQ.P. Shi and Y.M. Mo 237
Application of Pressure-Rate Deconvolution to Well Test Interpretation of LowPermeability ReservoirsY.H. Shen, S.L. He and H.L. Zhang 243
Research on Fault Diagnosis of Certain Armored Vehicle’ Gear-Box with IMF’s EnergyMomentC.F. Wang, G. An and F.J. Yang 248
Study on Energy-Saving of Urban Water Supply System Variable Frequency PumpingStationH.Y. Li and X.P. Yue 254
Study on Voice Transmission System of the Optical Fiber for Tube Leakage MonitoringInstallment in the Power Station BoileY.Z. Xu, H.Z. Chen, S.J. Ma and C.J. Zhao 260
Optimizing Back Surface Field of Heterojunction Thin-Film Solar Cells by NumericalSimulationG. Lu and L. Zhang 267
Identification and Quantitative Feedback Control of Precision Mechatronic SystemsX.L. Bao and X. Luo 272
On Monitoring and Testing System of the Hydropower Unit Vibration Based on VirtualInstrument TechnologyL.C. Wu, H.P. Nan, X.Y. Yu, D.L. Zhao, N. Li and C.Y. Ma 279
Fuzzy Control Technology for Drive System of Switched Reluctance MotorG.Q. Sun and B.R. Wang 285
b Manufacturing Science and Technology
Wavelet Neural Network Based Adaptive Robust Control for a Class of MIMO NonlinearSystemsY.H. Zhu and W.Z. Gao 290
The Research of DC/DC Power Storage Converter Controller Based on Hysteresis ControlL. Song, W.G. Li, J. Yang, C.Y. Zhang, T. Yan and D. Hui 297
A New Model of Intrusion Detection Based on Data Warehouse and Data MiningB. Qi and Y.F. Dong 303
Rapid Control Prototyping Design of DSP-Based Motion ControllerL. Li, Z.M. Peng, B.C. Zhang and Z. Tie 308
Control System Design and Data Communication Realization of Road Accelerated LoadingTest EquipmentJ.W. Zhang, X.G. Wang and Z.G. Guan 315
The High-Power of DC Power with Auto Tracking Power FrequencyG.Y. Yu 321
Design of New Automobile Rotational Speed Measuring DeviceG.Y. Yu and L. Zhang 325
High-Performance Sensorless Control of PMSM Based on Sliding Mode Current ObserverS.W. Fan and H.S. Liu 329
Rotor Design for High Speed PM Machine Based on Riccati Transfer Matrix MethodJ.Q. Wang and F.X. Wang 337
Multisensor Tracking of a Maneuvering Target in Clutter with Proposed Parallel UpdatingApproachS. Gao, M. Gao and Q.K. Xiao 344
Parameter Tuning for Sensorless Induction-Motor Drive Use Stator-Current-Based MRASEstimatorL.Y. Yang and L. Shuo 352
Research on Attitude Control of Spacecraft Based on ADRCF.L. Teng, H.Y. Ge, H.S. Li and J.H. Zhang 358
Automobile Reversing Radar Based on Ultrasonic WaveX.N. Wang, Q. Gao and P.C. Zhang 366
Design of a New Structure for Anti-Upsetting of Axle-End in Wheelset Disassembly andAssemblyY. Gan, J. Xiao and Q. Wang 372
Stress Distribution of Strip at the Parts in Contact with Roll in Continuous AnnealingFurnaceY.D. Xing, Z. Wen, R.F. Dou, X.H. Feng, Z. Li and B. Dong 379
A Hybrid Algorithm to Solute the Problem of the Robot Path PlanningQ.B. Yuan, H.J. Wang, P.H. Zhu and H. Zhao 385
Study on Start Burning Performance of Micro-ICP Using Stereo Spiral CoilY.Q. Wang, N. Chong, R.X. Sun, Y.C. Zhou and W.J. Chen 390
Application of Time-Frequency Distributions to the Blind Source Separation of MechanicalFault SignalsZ.H. Hao, H.X. Tian and L.X. Tian 395
The Study on a New Type of Full-Voltage Starting Method of Asynchronous MotorsX.M. Li, H. Wu, Y. Zhao and S.Q. Liu 400
Extracting of Weak Periodic Impact Feature Based on Mean Filtering and WaveletTransformF. Du and T.B. Ma 408
Research on Design Key Technologies for High-Power Submersible MotorY.M. Xu, D.W. Meng and J. Tan 414
Experiment the Influence of Subsection on Leakage Reactance in Submersible MotorY.M. Xu, D.W. Meng and J. Tan 420
Overview of the Low Voltage Ride-Through Technology for Direct-Drive PermanentMagnetic Wind Power SystemX.Z. Huo and X.N. Xiao 424
Design of Detection Device for Solar Photovoltaic Lighting System Charge-DischargePerformanceY.Q. Wang, P.P. Huang and R.X. Sun 430
Advanced Materials Research Vols. 383-390 c
Application of Improved RBAC in System Login Component DesignY.B. Cao, Y.X. Hua, J.S. Zhang, X.L. Liu and H. Zhang 435
An Optimal Design Method Based on Feature Technology for Micro DeviceZ. Liu and H. Chen 440
Dynamic Modeling of Single-Wheeled RobotX.G. Ruan and Q.Y. Wang 447
The Application of the Niching Genetic Algorithm to Optimum Design of the YKK SeriesInduction MotorZ.Q. Hu, G.Y. Hu and J.D. Zong 453
Design of a Remote, Real-Time Elevator Monitoring System Based on the µc/os-IIOperating SystemG.Z. Guo, P.J. Zhang, Z.Z. Yu, H.L. Wang and Y.L. Shi 459
Design of an Automatic Positioning System Used in Pipe Crawler Weld Based onTMS320DM642Y.J. Guan, H.M. Zhou and J.G. Sun 465
A High-Performance Signal Processing System for Monopulse Tracking RadarY.B. Hong, C.F. Xu, M.G. Gao and L.Z. Zhao 471
Core Loss Calculation in Step Magnetic of High-Speed Motor StatorJ.K. Xia, X.J. Wang, J. Zheng and H. Zhang 476
Design of Bending Fatigue Machine for Flexible ElectronicsH.W. Cao, P. Yang and B.Z. Bao 483
Cogging Torque Reducing in Dual-Rotor Motor by Suitable Selection Inner and Outer SlotOpening WidthsJ.K. Xia, Y.J. Zhao, C.Y. Wang and T. Dong 490
Design of the Underwater Acoustic Signal Acquisition System Based on the Pipelined Twin-ADG.K. Zhao, S.S. Ning, Z.W. Cai and Z.Q. Xu 497
Design of External-Rotor Ferrite Permanent Magnet BLDC MotorC.Y. Xu, Q.M. Li and C.L. Huo 503
Controlling of Brushless DC Motor Based on Particle Swarm Optimization Fuzzy LogicalControllerH. Li and J. Du 509
Design of the A/D Conversion Circuit Based on ARM for the Time-Difference MethodUltrasonic FlowmeterX.H. Zhang, H. Zhang, X.H. Chen, X.Q. Wang and J.Q. Feng 516
Evaluation on the Tensile Force of Geotextile and Geomembrane Used on the Side Slope ofa Waste LandfillS.F. Xu and Z. Wang 524
The Control System on Coke Machine Interlocking and Automatic RunningJ. Zhang, R.H. Li and H. Li 531
Design and Simulation of Variable Speed Constant Frequency Brushless Doubly Fed WindPower GeneratorK.J. Wu and Y.Y. Wang 537
Study of Modified Sliding Mode Control Strategy for STATCOM with LCL FilterR. Hou and C.P. Li 543
Design and Research of Crash Sense Module of Vehicle Emergency Call SystemH. Jiang, M. Li, Z.X. Li and S.B. Zhang 548
The Simulation and Research of Chaos in Current-Controlled Boost DC / DC ConverterW. Zhen and X.F. Liu 553
Multi-Model Adaptation Fuzzy Control for the Deep Sea Walking Hydraulic ControlSystemQ.B. Meng, Y.X. Yin and G.L. Qiao 558
Analysis of Reliability for Hoist Main Control System Based on Markov ProcessF. Wang, F.Y. He and D.C. Li 565
The Design of Mini Quad-Rotor Unmanned Aerial Vehicle Control SystemY. Zhao and J.X. Yang 569
The Synchronization Control of the Hydraulic Press Brake Based on the Virtual ShaftControl AlgorithmG.F. Liu, S.L. Li and L. Zhang 574
d Manufacturing Science and Technology
A Fuzzy Compensation Control System for Underwater Vehicle Based on Kalman FilterPredictorZ.J. Tang, P. Yan and L. Jun 580
A New Teaching Method in a Kind of Industrial Palletizing RobotM. Yao, B.L. Han, Q.S. Luo, T.Q. Lv and J. Xu 584
A New Engineering Model of Solar Array and MPPT ControlX.L. Wang, L. Yang and P. Yan 591
Optical Flow Sensor Designed for Altitude-Holding FlightX.M. Liu, W.C. Chen, X.L. Yin and X.L. Xing 598
The Robot Path Planning Based on Region Partition to Node OptimizationY.S. Liu 605
Research on the Hybrid Active Power FilterW. Fang, X.D. Cui and J. Wang 610
Performance Improvement on Edge-Based Human Detection Using Local ContrastEnhancementX. Yuan, X.Y. Wei and Y.D. Song 615
Simulation Study of Harmonics and Reactive Power in Three-Phase Full-Bridge ControlledRectifier Circuit with Resistance-Inductance LoadY.F. Wang, C.H. Yang, H. Xue and X. Yang 621
Measurement of Ultrasonic Attenuation Coefficient of MudM. Zhou, F.Q. Shao and L. Zhang 627
Trajectory Tracking of a Spherical Robot Based on an RBF Neural NetworkM.H. Zheng, Q. Zhan, J.K. Liu and Y. Cai 631
Limiting Power of High Power Microwave Pulses from ApertureJ.H. Zhang and W. Hu 638
An Improved Design of Controller for Medium Frequency Induction PowerZ. Zhang, X.W. Liu, M. Jiang and G.C. Wan 643
Parameters Identification of Induction Motor for Electric Vehicle Based on Least SquaresMethodJ.L. Zhang and C.S. Zhang 648
Study on VAV Temperature Fuzzy Controllers with Self-Tuning Parameters and VariableUniverseH.Z. He and S.H. Yang 654
Development of the Performance Testing System for Radio FuzeY.Z. Chen and W. Lin 661
Robust Data Reconciliation in Linear ProcessL.K. Zhou 667
Improved Differential Evolution Algorithm for Structural Optimization Design of Flumeswith Hybrid Discrete VariablesJ. Zhou, D.X. Zhang and X.L. Liu 672
The System of the University Experimental Physics Course-Choosing on ASPX. Li and H.D. Lu 678
Research on Permanent Magnet Linear Motor without Friction FeedY.P. Lan, H. Zhao and H.X. Lan 681
Application Research of CMAC-PID Control in Photovoltaic Tracking SystemJ.M. Xiao, L.Y. Jiao, H.M. Zhu and F.K. Xiao 687
Design on Novel Photoelectric Sensor for Refractive Index MeasurementY.L. Li, Z.H. Huang and K.B. Hu 692
Numerical Simulation of Hammer Forging Process for Inconel 718H. Yan and Z.M. Huang 697
Application Study of Active Disturbance Rejection Control TechnologyX.X. Shi and S.Q. Chang 701
Study on Rheo-Diecasting for In Situ Synthesized Mg2Si/AM60 CompositesH. Yan, Y. Hu and X.Q. Wu 707
A Study on Method of Map Conflation Based on Topological RelationshipD.C. He, J. Zhang and J.J. Chen 712
Advanced Materials Research Vols. 383-390 e
Excitation Control Strategy of Brushless Doubly-Fed Generator for Variable SpeedConstant Frequency Wind Power SystemF.G. Zhang, H. Li and S. Jin 717
Implementation of a DirectDrive Technology Realization DC-Coupled Output on Video-Output CircuitsC.X. Lv 724
Modeling and Testing a Screw Expander Integrated into a Trilateral Flash CycleZ.G. Wang, S. He, J.X. Li and G.J. Song 727
Research of Simulation Parameters of Oil Field Distribution Network Based on GreyPredictionR.H. Liu and Y. Cui 734
Chapter 2: Powder Metallurgy and Ceramic Forming
Nonlinear Immune PID Controller and its Application to the Heat Milling System’sMaterial-Level ControlJ.Q. Liu and W. Wang 743
A New Temperature Setting Control Method for Regenerative Rotary Reheating FurnaceF.Y. Su and Z. Wen 750
Study on Rapid and Non-Destructive Identification of Starch Categories with NIR (Near-Infrared Reflectance)X.R. Sun, C.L. Liu, J.Z. Wu and H. Li 756
Application of Improved Fuzzy PID Control Algorithm in Heating FurnaceH.J. Wang, D.X. Li, H.J. Qi and L.N. Liu 760
Research on Wood Powder-Based Rapid Prototyping TechnologyC. Jing 764
A Thermodynamic Model for Nearest-Neighbor Distributions in Annealed QuaternaryAlloysL.L. Tang and C.B. Wang 768
Design and Development on Piezoelectric Ceramic Type Insole 3D Force MeasurementSystem Based on LabVIEWY.M. Guo, L.M. Wang and R.Y. Xue 774
Manufacturing Execution System Based on the Soda Ash IndustryS.E. Cheng 780
Study on Characteristics of Metal V-Belt Infinitely Variable Power-Split TransmissionH. Pan and X. Cai 785
High Throughput Speciation Analysis of Mercury in Water Environment by Short ColumnCapillary Electrophoresis On-Line Coupled with Inductively Coupled Plasma MassSpectrometryB.H. Li and B.J. Tian 790
Chapter 3: Surface, Subsurface, and Interface Phenomena
Dynamical Integral Sliding Mode Control for Permanent Magnet Ring Torque MotorB.Q. Sun, X.W. Ge and Y.B. Sun 799
Study of Pulsed Magnetic Field Generator for Magnetoacoustic Tomography Technologywith Magnetic InductionY.H. Li, G.Q. Liu, S.Q. Li and H. Xia 805
The Infrared Characteristics of the Wall Temperature of Boiling Heat Transfer inMicrochannelH.G. Ma, J.M. Bai, R.J. Xie and W.J. Tu 811
Feed Forward Active Disturbance Rejection Control Method for Common-Rail PressureControl of Diesel EngineW.Q. Huang, Y.T. Zhang and G.J. Huang 816
Electrical Properties of Multilayer Synthesized CuInSi Thin FilmP. Luan, J.S. Xie and J.H. Li 822
The Impact of Surface Tension on the Oil-Water Stratified FlowD.Z. Xu, G.Z. Zhang and X. Zhang 826
f Manufacturing Science and Technology
Improvement of Crystal Growth Control SystemD.J. Song, B.X. Tan and J.C. Liu 830
Starting Performance of Novel Magnet Arrayed Permanent Magnet Synchronous MotorY.J. An, H.L. Wen, W.Q. Zhao, G.M. Liu and Z.J. Meng 835
Research on the Microwave Propagation in the Evaporation Duct with ObstaclesG.C. Li, L.X. Guo and T.T. Zhang 840
Performance Experiment of Natural Refrigerant Cascaded Refrigeration SystemJ.H. Ning and S.C. Liu 846
Ultimate Slip between FRP and Concrete on their InterfaceQ.F. Yang and Q.L. Meng 852
The Effect of Drag-Reducing Polymer on Heat Transfer in Gas-Liquid Two-Phase FlowL. Liu, Q.Y. Guo, X.F. Guo, H.Q. Fan and Z.H. Zhong 856
Determination of Trace Level Oxytetracycline and Influences of Coexisting Pollutants on itsSorption by Three Kinds of SludgeM.H. Huang, L. Chen, D.H. Chen and Y.D. Yang 862
Research on the Coupling Relations of the Possible Factors Affecting Ammonia NanofluidBubbling AbsorptionW.D. Wu, H. Zhang, W. Sheng and Z.Y. Li 866
FEM of Residual Stress of EDMed SurfacesC.K. Biswas and M.K. Pradhan 872
Interfacial Microstructure and Strength of Friction Welding of Steel Tube to AluminiumTube Plate Using an External ToolS. Muthukumaran, C.V. Kumar, S.S. Kumaran and A. Pradeep 877
Application of Taguchi and Response Surface Methodologies for Surface Roughness inRotary Tool Polishing Hardness Mould SteelsP. Potejana and C. Thongchattu 882
The Effects of Materials Properties & Angle Junction on Stress Concentration at Interfaceof Dissimilar MaterialsA.F. Arezoodar and A. Baladi 887
Wear Behavior of Surface Treated Alloy Steel with Assorted Blends of Fine Particles byUsing Plasma Spray ProcessR. Dhanasekaran, P.S. Kumar, S. Baskaran and K. Santhi 893
A Study on Interfacial Reaction and Titanium Distribution in Brazing Sapphire to Inconel600 Using Cu/Ni Porous CompositeT. Zaharinie, F. Yusof, M. Hamdi and T. Ariga 898
A Study on the Effect of Process Parameters on Surface Topography of Al Thin Films onVarious Substrates Using AFMS. Shanmugan, D. Mutharasu, Z. Hassan and H.A. Hassan 903
Chapter 4: Composite Materials
Preparation of Geopolymer Using the Slag from Direct Reduction-Magnetic Separation ofRefractory Iron Ore (SDRMS)H.F. Yang, C.G. Dang and W. Xu 911
Research of Person-Parachute System Motion in Free-Fall PhaseY.X. Yu and Y.F. Wang 916
Dexterous Robot’s Finger Actuated by Pneumatic Artificial MuscleB.J. Guo and K. Wang 920
Study on PMV Index Forecasting Method Based on Fuzzy C-Means ClusteringC.C. Zhang, X.G. Chen and Y.Q. Xu 925
RVE Based Numerical Evaluation on Effective Mechanical Properties of Composite withRandomly Distributed Multi-Phase InclusionsC. Li, L. Chen and L. Qiao 931
Preparation of Modified Cu-Antibacterial White Carbon Black by Microwave DryingB. Zhang and X.N. Tang 935
Study on Morphological Structure and Application of Ag-La-Inorganic AntibacterialMaterial Dying by MicrowaveB. Zhang and X.N. Tang 941
Advanced Materials Research Vols. 383-390 g
A Study on Ammonia Nitrogen, Phosphorus and Organic Pollutants Removal of Zeolites bySalt ModificationH. Lin, Z.Y. Zhao, L.Y. Jiang and W. Wei 947
Effect of Ultrasonic Wave on Ni-P-Al2O3 Electroless Composite Coating on MagnesiumAlloyY.Z. Fan, L. Ma and X.M. Cao 953
Processing Method and Property Studies of Composite GeotextilesQ. Cheng 958
Chapter 5: Computer-Aided Design in Materials Engineering
Computations for Simplification of Canned Cycles in CNC Programming for TurningOperationsV.K. Malviya and P.K. Jain 965
Application of Stochastic Differential Equation and Optimal Control for EngineeringProblemsR. Rezaeyan 972
Multi Objective Optimization of Noise and Vibration in Passenger Car Cabin by Using GoalProgramming ApproachA.K. Junoh, Z.M. Nopiah, W.Z.A.W. Muhamad and M.J.M. Nor 976
A Framework for a Development of an Intelligent CNC Controller Based on Step-NCD.M. Elias, Y. Yusri and M. Mohamad 984
Realization CNC Controller Enable Machine Condition Monitoring Architecture Based onSTEP-NC Data ModelF. Ridwan and X. Xu 990
A Study on Extraction Method of Non Geometry Information in Engineering Drawing TitleBlockM.F.M. Amran, R. Sulaiman, S. Marjudi and S. Kahar 995
Identification and Fault Diagnosis of an Industrial Gas Turbine Using State-Space MethodsI. Yousefi, H. Khaloozadeh and A. Ashraf-Modarres 1000
Study on the Optimization Process Technology in NC Machining Based on thePolychromatic Sets TheoryE.F. Liu, X.Y. Liu and Y.X. Fang 1007
Adaptronic Systems in Robot ManufacturingB. Denkena, J. Immel and M. Schönherr 1013
Prediction of Tensile Behavior of DP 590 Steel Tailor Welded Blanks by ANNS.K. Dey, R. Ganesh Narayanan and S.K. Gurunathan 1019
Design a Low Noise 5GHz Differential Cross-Coupled VCO and Colpitts VCO UsingBiCMOS TechnologyS. Nemati, N.K. Najafabadi and M. Dousti 1027
Robust Part Quality by Controlling the Injection Moulding Process with 24 FractionFactorial Design: A Case StudyS. Rajalingam 1032
Web Adds
Weighting Matrix Selection Method for LQR Design Based on a Multi-ObjectiveEvolutionary AlgorithmM.A. Nekoui and H.H.J. Bozorgi 1047
Secondary Development of Blades Parametric Design of Hydraulic Torque Converter Basedon CATIAP. Guan, J.C. Dong and L.G. Wu 1055
Single Input Multi Output Adaptive Network Based Fuzzy Inference System forMachinability Data Selection in Turning OperationsA.H. Suhail, N. Ismail, S.V. Wong and N.A. Abdul Jalil 1062
Applying a Modified Particle Swarm Optimizer to Section Optimization of Steel FramedStructuresB. Yang and Q.L. Zhang 1071
h Manufacturing Science and Technology
Research on the High Frequency Realization of High-Power InverterR.H. Liu and G. Wang 1077
A Study on the Characteristics of Planar Motor with Halbach ArrayR. Huang, S.H. Wu, H. Sui, F.L. Jiang and B. Hu 1084
Stability Analysis of Beam’s Non-Linear Vibration with Time-Delay Feedback ControlC.C. Liu and D.H. Zhang 1090
Multi-Rate Digital Control for Pulse Detonation Engine Control ApplicationsX.H. Wang and D.R. Yu 1095
Implementation of Turntable Servo Control System Based on Fuzzy Self-Tuning PIDY.M. Wu, J.J. Wang, G.Z. Cui and W. Deng 1101
Contour Extraction of Flame for Fire DetectionY.Y. Yan, S.B. Gao, H.Y. Wang and Z.B. Guo 1106
Simulation Research on the Variable Step Size MPPT Control for PV SystemY.X. Ling, W. Chuang and L.S. Jun 1111
Comparisons between Topologies of Flux-Switching Electrical MachineT.T. Zhu, Z.Q. Deng and Y. Wang 1117
The Unified Design for Inter-Area Stability Control Based on BacksteppingM. Xu, L. Zhu and Z.X. Cai 1124
Using Governor Sensitivity Test Method to Analyze Moment of Inertia of Engine GeneratorSetW.Q. Teng, Z.Y. Ren, Z.Q. Wang and B. Lv 1131
Systemic Design of Four Vat Energy-Saving Quenching Machine ControllerS.S. Zhang, Z. Liu and Z.X. Zeng 1138
Esterification Research on a Bio-Oil Model Compounds System with an Optimal Solid AcidCatalystY.L. Gu, G.H. Xu, Z.G. Guo and S.R. Wang 1144
Influences of Clearance in the Nether Wearing Ring on the Self-Excited Vibration of theFrancis TurbineD.L. Zhao, W.K. Liang, H.P. Nan, W. Ma, J.B. Li and T.T. Li 1150
Navigation System of Mobile Platform Based on Open Architecture for AgriculturalMachineryJ. Song 1155
Synchronization Control Strategy Applied in Two Cylinders System of Rolling MillL.X. Wei and J.C. Zhao 1160
Electromechanical Actuator Controller Design with Optical Encoder FeedbackX.M. Liu, W.C. Chen, X.L. Yin and X.L. Xing 1166
Study on Assessment Model of Lightning Proof Abilities of HV Transmission Line Based onArcGISG.F. Lai, Y.F. Ji, Z.P. Gu and G. Liu 1174
PXI-Based High Performance Data Acquisition System for Fuel Injection System of DieselEngineX.J. Song, W. Liu, B.X. Tan and W.G. Chen 1181
Research of Video Tracking Algorithm Based on the Blob AnalysisZ.P. Zhang and S.H. Li 1185
Generalized Multiple-Model Adaptive Estimation for Mars Entry NavigationK. Wu 1190
Research on Transient Fuel-Film Compensation Control Strategy for a Port-Fuel-InjectedEngineJ.H. Zhou, Y.N. Yuan, K. Wu and J.Y. Du 1195
The Air Controlled Hydraulic System Design of 3201z-Type Dump Truck LiftingMechanismsT.P. Yan 1202
The Design and Analyses of Magnetorheological Fluid Throttle ValveR. Wu, W.X. Lin and W. Tang 1208
Design of Automated Distillation Analyzer Based on STM32W.G. Chen, X.J. Song and W. Liu 1215
Seal System Optimization Study of an On-Off Valve Based on CFDX.D. Hu, Q.S. Gong, L.X. Gong and J.T. Lv 1219
Advanced Materials Research Vols. 383-390 i
Hoist Safety Risk Assessment Model ResearchJ.G. Yi, X. Cai, J.C. Xu, H.X. Li and S.X. Dai 1225
Research on Auto Control System for Ship Loader Based on AC800MW. Liu and S.L. Xue 1231
Motor Position Detection Unit for Servo Control ApplicationS.Z. Song and J.Z. Shi 1235
A Mesh-of-Appendixed-Trees-Based Technique Carried on the Crossed CubeZ.Y. Zhang, S.Z. Liu, F.Q. Zhang and C.H. Yu 1241
Key Establishment Scheme for Distribution Automation System Using Logical KeyHierarchy ApproachZ.W. Sun, R.G. Zhang and D. Liu 1246
Research on State Intelligent Maintenance Based on Sonic Information of PowerTransformersX.H. He and M.C. Xia 1250
Research on Technology of Thrust Asymmetry Lateral Compensation for Large AircraftM. Ji, J. Jiang, W. Xue and Z.X. Lin 1256
Application of Fuzzy Control in Transformer Cooling SystemZ.G. Jia 1262
Time-Varying Sliding Mode Control for Linear Motor Servo SystemY.B. Sun, L. Yang and C.Y. Wang 1267
Human-in-the-Loop Intelligent Control System for Continuous-Flow Grain DryingS.J. Wang 1273
Combined Simulation Based Commutation Failure Analysis in HVDC SystemsW.B. Ci and Y.T. Liu 1279
A Novel Automated Balancing and Correcting MachineZ.Y. Zhang and J.L. Li 1285
Analysis of Fault Recorder Data for Short-Circuit Current in a 500kV Busbar Short-CircuitAccidentW. Cao, Y.S. Wang, B. Liu and W. Wang 1290
Electromagnetic Design of Dual Stator-Winding Induction Generator System with BoostConverterX.J. Shi, L.S. Liu and S.T. Zhang 1295
Interaction and Coupling of RobotH.B. Xin and Q. Huang 1299
The Study of the Multi-Body System Theory on Basis of CNC Milling Machine ErrorC.J. Zhu, Q.S. Qin and P.E. Bao 1304
Design of Underground Mining Personnel Locating System Based on nRF24L01W.G. Chen, X.J. Song and W. Liu 1310
The Realization of Palm Kneading for Chinese Massage RobotG.Y. Du, S.Y. Lu and H.K. Zhang 1313
Path Planning of Avoiding Obstacle for Fruit-Picking Manipulator Based on PositionInformationY.F. Wang, J.J. Yin and S.F. Chen 1318
Design of Direct Yaw Moment Control System to Enhance Vehicle Stability Based on FuzzyLogicZ. Xu, M.X. Wei, Y. Wang and J.W. Wei 1326
High Efficiency 500W RF GeneratorW. Qin, Y.T. Li, Y.J. Li and X.P. Xu 1333
Design of Remote Transmission System for Wireless Heat MeteringX. Wang, R.J. Ma and E.P. Zhang 1337
The Optimal Controller Design of Zero Steady-State Error for Nonlinear Systems withComposite DisturbancesD.X. Gao and R. Wei 1343
Research on Linear Motor for Linear CompressorW. Wang and Y.M. Xia 1350
Simulation and Parameters Tuning of Second Order ADRC Controller in SimulinkY.J. Ma, Y. Yu, X.S. Zhou, C. Li and S.J. Liu 1356
j Manufacturing Science and Technology
Active Power Smoothing of Wind Generator Based on Wind Speed Prediction and Inverse-SystemX.L. Wang and J. Wu 1363
The Method of Pole Width Modulation Reducing Cogging Torque in Permanent MagnetMotorY.J. An, W.Q. Zhao, L.P. Xue, H.L. Wen and G.M. Liu 1369
Fault Feature Extraction for Gearboxes Using Empirical Mode DecompositionC.H. Dou 1376
Development on a Test System for Starting Relays Based on IPCZ.F. Liu, Q. Yan and Y.G. Zhang 1381
Determination of Key Technical Parameters of Special Hydraulic Turbine for CoolingTowerY.P. Li, H.P. Nan and K.C. Duan 1386
Research on the Design of Linear Drive Motor of New Pumping UnitW.Z. Ma, H.M. Zhang, J.Y. Sun, D.B. Tian and H.F. Pang 1391
Research on the Pumping Unit Model Driven by Linear MotorW.Z. Ma, J.Y. Sun, H.M. Zhang, D.B. Tian and H.F. Pang 1399
Statistical Method for Rotating Machine Fault DiagnosisZ.M. Zhuang and F.L. Li 1406
Research on Knowledge-Based Injection Mould Project Design SystemL.F. Han, S.Y. Zhong, W.F. Ding and T.X. Liu 1411
The Optimization of ITD in Direct Air-Cooled SystemL.J. Chen, C. Xu, Y. Wang, L.J. Mi and X.C. Shi 1417
Research on the Multi-Parameters Matching Control of the Cooling System for the DieselEngine on the Numerical Simulation TechnologyZ.Y. Sun, X.R. Li, L.P. Guo and X.Y. Zhang 1423
Research on Parametric Design Method of Combustion Chamber on Diesel EngineY. Shang, F.S. Liu, X.R. Li and J. Wu 1431
The Review of Technology of Power Quality Disturbances GeneratorW. Zhu, X.C. Tu and C.C. Qu 1441
The New Elman ANN Application in Accuracy Improvement of Robot Navigation andObstacle Avoidance TechnologyX.K. Du 1447
UAV Automatic Landing Control LawM.H. Liu, C.T. Li and Y. Wang 1452
Design and Application of Long Distance Oil & Gas Pipeline Stress & Strain MonitoringSensorY.B. Ma, Y.J. Cai, D.J. Tan and Z.X. Hu 1458
Modeling of Distillation Tower Temperature Based on D-FNNS.Z. Gao, J. Yang and J. Fan 1463
Research on a New Type of Lithium Battery String Equalization and Management SystemH. Wang, D.G. Shao and L. Xu 1470
Application of FSK Technology in Welding MachineL. Qian, S.S. Zhang and F.X. Hao 1477
New Idea of the Multilevel Leakage Protection in Underground LV Distribution NetworksY.L. Liang 1481
Research of Linear Differential Hall Sensor Modeling and Output CharacteristicsExperimentZ.Y. Qiu, Z.B. Zhang, Q.T. Liu and G.D. Jiang 1488
Application of RBF Neural Network in Dynamic WeighingQ. Jiang, X.Q. Shen, J.H. Cai and Y. Yao 1495
A New Method of Rolling Prediction for Gas Emission Based on Wavelet Neural NetworkY.M. Pan, X.Y. Zhang and P.Q. Xue 1500
The Design of Five Degree of Freedom Robotic Arm SystemC.K. Xu, M. Li and Y.J. Liao 1507
2-Phase Symmetrical PWM Generator Using CPLD for Ultrasonic Motor DriveW.Y. Zhang and J.Z. Shi 1513
Advanced Materials Research Vols. 383-390 k
Nonlinearity of PMSM’s Low-Speed Operation Caused by Dead-TimeW.Y. Zhang and J.Z. Shi 1518
Model and Auto Take-Off Control Law Design of Unmanned Aerial VehicleH. Song and X. Chen 1524
Digital PID Algorithm of Navigation System for Spraying RobotJ. Song 1531
Study and Implementation of Fault Diagnostic Algorithms on Hydraulic Power Cart forAircraftH.B. Zhang and H. Yang 1536
Low-Cost PLC-Based Control of a 2-DoF Purely Translational Parallel RobotZ.B. Li 1542
A Misfire Fault Diagnosis System Based on Improved Neural NetworkK.Y. Zhang, J.W. Deng and D. Lu 1549
Modeling of Multi-Agent System for Drilling SimulationW.L. Wang and Y.J. Wang 1555
Design for the High-Rise Cable-Suspended Rescue RobotK. Luo and C.Z. Deng 1562
Servo Motor Synchronous Control System Based on PMAC ControllerY.P. Yao, M.X. Dai, J.Y. Fei and Y. Shi 1568
Research of Redundancy Management on Fight Control Computer for Unmanned AerialVehicleL. Liu, X. Chen and D. Cao 1573
Research on Internal Communication of Redundant Flight Control Computer for UAVL. Zheng, X. Chen and X.H. Lv 1578
Study of Missile Radiator Predicting and Tracking Technology on the Basis of KalmanFilter and Mean-Shift AlgorithmZ.H. Xu, B.Q. Mao, L. Xu and J.Y. Zhao 1584
Research of Optimal End Guidance Law about Target-Seeking UAV under PassiveGuidanceJ. Cao, X.P. Zhu and J.F. Wu 1590
The Software Design and Implementation of a Real-Time Automatic-Tracking SystemX.Y. Liu and B. Gu 1595
Infineon Microcontroller Based Frequency Converter DesignX.C. Lv and W.F. Li 1600
Motion Consistence and Textural Coherence based Error Concealment Algorithm forCorrupted MacroblockJ. Chen and C.H. Cai 1605
Intelligent Autonomous Navigation System for the Wheeled Mobile RobotT.M. Dat, Y.F. Neil Nieh, M.F. Ricky Lee, W.N. Khotimah and L.Q. Dat 1611
Trajectory Control Using Linear Control System on Mobile RobotK.Y. Chang, H.J. Hsu, P. Alexandra and M.F. Ricky Lee 1619
Start Control of Ultrasonic Motor Based on Neural NetworkH.M. Zhang, H.Y. Wang, J.Z. Shi and X. Liu 1623
New Method for Construction Land Prediction Incorporating Genetic Algorithm andSupport Vector MachinesY.Y. Luo, L.T. Zhang and H. Zhang 1629
Research on Powertrain System of Series HEB Control Strategy SimulationC.S. Si 1635
Research on Management Information Platform of Dynamic Water Rights Based on GridTechnologyC. Feng, C. Zhang, J.C. Xie and N. Wang 1641
Energy Storage and Deposition Characteristics of Spark Ignition SystemD.J. Wang, H.G. Zhang, X.N. Sun and D.J. Wang 1647
System Based on BP Network for Garment Quality Forecast and ManagementX.P. Zhang and X.X. Yang 1653
Numerical Analysis on Propagation and Fatigue Life of Asphalt Pavement Surface CrackH.C. Wang and G.F. Li 1658
l Manufacturing Science and Technology
Parameterized and Modular Theory Used in Rapid Design System of Simi-Trailer TankerJ.G. Wang, Z.C. Cui and L.Z. Liu 1664
Chapter 6: Casting and Solidification
Study and Application of the Variable Torque Slipping Clutch with Skewed RollersM. Feng, W. Xing, J.W. Lian and G.R. Yan 1671
Hybrid Genetic Algorithm-Based Production Planning for Steel-Making and ContinuousCasting ProcessD.F. Zhu, H. Wang, S.B. Wang and J.X. Xu 1677
Mudstone Creep Test and Numerical Stimulation of Casing Loads in Deep WellZ.Q. Xu, X.Z. Yan and F. Bu 1684
Research on the Integration Credibility Model of COTSS.P. Wei, L.Q. Shen and H.J. He 1691
Simulation and Implementation for the Speed Control System of Horizontal ContinuousCasting Dragger for CopperY.D. Chen and Z.H. Xia 1696
The Analytical Solution of Single Pipe Piles under Axially and Laterally Free LoadsZ. Wang, S.F. Xu, G.C. Wang and Y. Zhang 1701
Analysis of Piles Subject to Axial Load and Lateral Soil MovementZ.F. Zhang and J.P. Li 1708
Experimental Research on Vacuum Casting of Micro-GearsX.M. Zuo 1714
A Novel Technique for Crack Resistance of Bulk Mass Concrete PierH.B. Zhu, P.M. Wang, G.T. Yan, C.S. Wang, Y.S. Cheng and L.M. Wu 1719
The Application of New Blasting Technique on the Replacement of Soft Silt Foundation byRock FillingJ.X. Zhang, X.G. Wang and S.W. Chen 1725
Properties of Pressurized Lost Foam Casting of Al-11Si AlloyA.A. Niakan, M.H. Idris, A. Ourdjini and M. Karimian 1730
Formation Behavior of Intermetallic Layer on Die Material in Casting Al-Si Alloy with theVariation of Fe ContentB.H. Kim, S.W. Lee and S.M. Lee 1735
Rapid Solidification Processing: Melt Spinning of Al-High Si AlloysF. Alshmri 1740
Chapter 7: Machining
Synthesis of Zeolite Membranes from Coal Fly AshS. Shirakura, S. Kojima, K. Tanaka and H. Kita 1749
Improvement of Local Decrease in Material Thickness on Fuel Filler TubeN. Kamei and H. Watari 1753
Powder Mixed Micro Electro Discharge Milling of Titanium Alloy: Investigation ofMaterial Removal RateM.Y. Ali, N.A.B.A. Rahman and E.B.M. Aris 1759
A Method to Reduce Milling Time for Ti-6Al-4V Alloy for Controlled Depth Milling UsingAbrasive Water Jet MachiningV.K. Pal and P. Tandon 1764
Investigation of Static Failure for Cemented Carbide Cylindrical End MillE.E. Khine, Y.D. Zhang and Q. Wu 1769
The Using of Anti-Sulfur Drill Pipe in High Sulfur Oil-Gas FieldF. Li, D. Feng, J.W. Wang and D.L. Gao 1776
Backstepping Adaptive Control of NC Tool Crossbeam Magnetic Levitation SystemC.F. Liu, Q.G. Chi, L.M. Wang and Q.D. Guo 1781
Static Performance Parameters and Analysis of the Hydraulic Expansion ToolholderS.L. Wang, W.Z. Zhang, G. Liu and B. Zhou 1787
Advanced Materials Research Vols. 383-390 m
Design about Monitoring and Diagnosis System Structure of Rotating Machinery Based onLabVIEWY.J. Lu and Y. Liu 1792
Decomposition of Cefotaxime Sodium Wastewater by Ultrasonic Fenton MethodK.B. Luo, P. Ning, H.P. Li and J. Chen 1797
Finite Element Simulation of the Residual Stresses in Butt Weld Plate of Aluminum AlloyX.H. Yang, Y.L. Song, G.W. Ran and T.J. Xiao 1801
Vibration Simulation of Articulated Dump Truck with the Variation of Longitudinal Centerof Gravity Position of Rear Sprung Mass and Rear Suspension StiffnessX.Y. Zhang and W.M. Zhang 1812
Development of Drill Monitor and Operation Mode Recognition Based on All HydraulicCore Drilling RigT. Zhang, T.N. Yan, L.Z. Zhou and C.D. An 1819
Research on Starting Process of a Novel Wound Rotor Line-Start Permanent MagnetSynchronous MotorG.H. Feng, S. Li, M. Zhao and B.Y. Zhang 1825
A Finite Element Analysis of the Normal Combination Round and Spline Broach Based onANSYSG.G. Zhang, J. Sheng and F. Wang 1831
Performance Analysis of Doubly Excited Brushless Machine with Radially LaminatedMagnetic Barrier RotorH.J. Liu and L.Y. Xu 1837
Study on Electronic Excitation Temperature of Argon Plasma Using Low Pressure Micro-ICP Excitation SourceY.Q. Wang, N. Chong, L.M. Dong, Y.J. Tang and H.J. Song 1844
Analysis on Variability of Mechanical Parameters in the Process of Rock DamageW.H. Tan, L. Zhang, D.Q. Gao and Y.L. Li 1849
Influence of Rotor Structure on Starting Performance of PMSM Used for HEVW.L. Li, Z.P. Li and T.T. Chen 1855
Broken Rotor Bar Fault Detection AnalysisL.L. Sun and K.B. Chen 1862
The Synchronous Control Study of once Forming Leaf-Spring Rolling MillL. Zhang, S.L. Li and G.F. Liu 1867
Oscillation Characteristic of Single Free Piston Engine GeneratorC.L. Tian, H.H. Feng and Z.X. Zuo 1873
Experimental Research on Regenerative Braking of Wheel-Hub MotorB. Wang, R.G. Wang, Q.Y. Cai and H.W. Sun 1879
Collapsing Pressure of Casing Located at the Bend Part of Casing-Exit Sidetracking WellZ.L. Tian, H.L. Yang, X.Z. Yan and Z.Q. Xu 1884
Round-Guard System Based on the Vibration Cable TransducerX.R. Sun, H.L. Ma and X.H. Du 1891
Static and Dynamic Characteristics Study of Wind Turbine BladeJ. Zhu, X. Cai, P. Pan and R.R. Gu 1895
Study of Fluxing Process for Hot Dipping Galfan Alloy on Steel WireA. Du, Y. Huo and J. Hu 1901
Research on Growth Process and Microstructure of Microarc Oxidation Coating onTitaniumS.J. Li, J. Hu and X.M. Cao 1905
Research on the Characteristic of Diesel Elastic-Plate Impingement SprayC.Y. Wang, F.S. Liu and X.R. Li 1910
Experiment Study of Chip Formation and Cutting Force of Hardened AISI 1045 Steel inHigh Speed MachiningG.H. Li, B. Yan and Y.J. Cai 1915
Analysis of Main Dimensions Effects on Performance of Transverse Flux SwitchedReluctance MotorsZ.G. Wang, P. Tan and S.C. Qu 1921
Study on Acoustic Emission Source Character of Various Welding Defect TypesW. Wang, Y.T. Dou, H.X. Wei, H.M. Heng and Y. Zhen 1926
n Manufacturing Science and Technology
The Experiment Research on Applying Air Source Heat Pump in Boiled Water MachineW.X. Shi, W.Y. Li, L.S. Pan and Z.H. Zhou 1933
Scattering by a Conducting Infinite Cylinder Illuminated with a Gaussian BeamZ.W. Shi, B. Zhang and X.M. Sun 1938
Research of Catalytic Performance over Transition Metal Modified MnOx-CeOx/ACFCatalystsB.X. Shen, T. Liu, N. Zhao, J. Ma and X.C. Hao 1945
Chapter 8: Modeling, Analysis, and Simulation of ManufacturingProcesses
Control and Robust Vision Relative Navigation for Autonomous Aerial RefuelingJ. Guo, X.M. Dong, L. Wang, H.B. Li and Y. Chen 1953
Transient Stability Simulation by Explicit and Symplectic Runge-Kutta-Nyström MethodF.Z. Wang, Y.F. He and J. Ye 1960
Research of Redundancy Management on Dual-Redundancy Brushless Direct CurrentElectric Rudder LoopH.B. Ye and X. Chen 1965
Research on Islanding Detection for Grid-Connected Inverter and Protection CriterionBased on Fuzzy Clustering AnalysisJ. Dong and Y.J. Rong 1971
Characteristic Analysis of the Coupled Harmonic Model and its Application in HarmonicPower FlowY.Y. Sun and C. Wang 1977
Design and Achievement of the Erection Test System Controlled by Single Neuron PIDControllerY.Y. Qiao, X.S. Guo, Z. Zhu and D.L. Cun 1983
An Algorithm of Converting UG Model to MCNP Geometry ModelJ.S. Zhang and X. Zhan 1988
Modeling and Analysis of Electro Hydraulic Brake System Based on AMESim/MatlabZ.L. Jin, Y.Q. Zhao, R.K. Shi, L.S. Guo and Z.T. Shi 1994
Modeling and Design of Hydraulic Driving Hobbyhorse Clamp HolderB. Li, W.L. Zhu, H.X. Gao and Q. Zhang 2000
Extreme Weather Loading Risk Model of Overhead Transmission LineY. Sun and X.L. Wang 2005
Fuzzy Control of Vehicle Suspension SystemG.Q. Yang and Y.Q. Zhao 2012
Study on Simulation of Three-Phase Z-Source Inverter for Grid-Connected Wind PowerGenerationH.Q. Zhang, P.F. Wei and W.W. Li 2018
High-Sealing Microvalves for PCRX.T. Li and A.Q. Wang 2025
Waveform Relaxation-Based Large-Scale Circuit Simulation for MOSFET and LossyCoupled Transmission Line CircuitsC.J. Chen, C.J. Lee, C.L. Tsai, A.Y. Chang and T.H. Shih 2031
Effect of Magnetic Circuit’s Structure Parameters on Torque-Speed Characteristic forElectromagnetic DamperY.F. Wang and L.L. He 2038
Numerical Simulation of the 1.2MW Wind Turbine Flow-FieldS.H. Li, Q.F. Kuang, W.P. Yue and T.T. Guo 2045
Theories on the Digitalized Intelligentized, Networked, Miniaturized Development ofElectronic TechnologyJ.M. Li 2051
Research on Transient Stability Simulation of Ship Power SystemH.L. Wang, C.L. Zhang, X.N. Kong and H. Zhang 2055
The Fine System-Level Calibration Technique of Size Effect Error for the Fiber-SINSL.F. Zhu and C.X. Zhang 2060
Advanced Materials Research Vols. 383-390 o
Analytic Prediction of Inductances for Toroidal Motor with Concentrated WindingsX. Liu and L.Z. Xu 2066
Design and Application of the Multifunctional Digital Automobile InstrumentC.X. Yu and W. Zhao 2073
Weak Coding Signal Detection under the Background of Sea ClutterS.H. Liu, Z.J. Sun, W. Sheng and Z.M. Hu 2077
An Optimized Angle Control Strategy for Doubly Salient Electro-Magnetic Motor Based onthe Half-Bridge ConverterG.S. Li, J.D. Wei, C.C. Chen, B. Zhou and C. Han 2083
The Study on the Fuzzy Control Algorithm for Main Steam Pressure Control of CirculatedFluidized Bed BoilerZ.J. Wang, N. Han and J. Wang 2092
Analysis of Tribological Characteristics between Plastic and Steel Helical GearY.S. Hao, B.G. Zhang and B. Peng 2097
Simulation and Research on Double Cylinder Hydraulic System Synchronized Control forSegment Erector of TBMW.N. Qiu and T. Zhou 2103
Real-Time Optimization of Transportation System for Earth-Rock Filled Dam Constructionwith GPS-Based Monitoring SystemD.H. Liu, K. Jiao and J. Sun 2108
Salient Pole Force Analysis and Inhibition of Tubular Permanent Magnet LinearSynchronous MotorJ.H. Zhao and J.H. Zhang 2116
Modeling and Simulation of Propeller and Hull System for Marine Propulsion PlantR. Li, W.X. Zhang and H.Y. Li 2121
Design of Coarse-Fine Combined Synchronization Control System for Lithography Basedon Cross-Coupled Sliding Mode ControlZ.P. Wu and X.L. Chen 2126
Internal Model Control of Three-Phase Four-Leg Active Power Filter Based on Online LS-SVM ANN Inverse System MethodH. Qi and Z.H. Shao 2132
Research on Stability of Networked Control System with Uncertain Time-Varying DelaysW.H. Ma and C.Y. Jin 2138
An Improved Z-Source Boost-Buck Rectifier Topology with Lower DC Output VoltageJ. Shang, Z.Z. Liu, Y. Zhang and S.H. Duan 2145
Fuzzy Hierarchy Comprehensive Evaluation on Dam-Break Risk AnalysisX.L. Wang, Z.Y. Zhou, R.R. Sun and S.S. Zhou 2151
A Simplified Model of Write Amplification for Solid State Drives Adopting Page-LevelAddress Translation MechanismW.N. Wang, Z.C. Wang, K. Ni, Y. Zhao, J.S. Ma and L.F. Pan 2156
Stabilization for Quantized Feedback Control Systems: An LMI ApproachJ. Fang 2161
Optimization Design on the Iron Beam Sectional of the Electricity TransformerC. Dong and X.W. Yue 2168
Simulation Research of AC Servo Driver Speed Adjusting System Based on SVPWMX.P. Yuan, Z.H. Fang and H.Y. Li 2173
An Adaptive Tracking Algorithm of Maneuvering TargetZ.S. Shi, P.X. Zhang, R. Li and S. Wang 2179
New Method to Ameliorate the Large Telescope Speed SmoothnessJ.X. Liu and H.W. Li 2184
Improved Power Flow Algorithm Incorporating Multi-Terminal VSC-HVDCF. Ye, Z.N. Wei and G.Q. Sun 2188
Radial Laminated Magnetic-Barrier Rotor Optimization Design of Brushless Doubly-FedMachineM.Z. Shangguan, H.J. Liu and Q. Zhang 2195
Analysis on Ground Subsidence in Underground MiningX.X. Liu and X.Z. Wang 2201
p Manufacturing Science and Technology
Numerical Simulation of Flow Field in Burnt Lime HydratorM.H. Bai, Y. Zhang and Q.F. Wang 2206
Thermal Stress Simulation of the Surface GrindingC.L. Hua, G.C. Wang, H.J. Pei and G. Liu 2211
Numerical Simulation of Particle Axial Mixing in Rotary KilnS.H. Li, X. Zhang, L.D. Zhang, K.S. Yu and W.J. Hao 2216
An Automatic SoC Design Methodology for Integration and VerificationD. Ma, K. Huang, S.W. Xiu, X.L. Yan, J. Feng, J.L. Zeng and H.T. Ge 2222
Modeling of Electromagnetic Heating SystemsW.J. Gao, L.Z. Li and W.S. Peng 2231
Design and Analysis of a Piezoresistive Accelerometer with the Film-Island StructureX.M. Yang, W. Zhang and W. Zhao 2237
Application of Model Predictive Control Based on BPNN to Heating BoilerY.P. Wang 2242
The Optimization Model and its Algorithms for Multiple Transportation Modes Selection inthe Fourth Party LogisticsG.H. Li and M. Huang 2249
Analysis of Reactor Magnetic Circuit Based on ANSYS Command FlowP. Yang, Z.D. Yin, R.C. Cui and N. Kong 2256
Numerical Simulation of Fluid Transients in Servo-Controlled Hydraulic PipingD.J. Mu and C.C. Li 2262
Analysis of Snubber Circuit Parameters Based on an Excitation Controlling CircuitW. Gao, J.H. Zhang, X.S. Wu and J.H. Zhao 2269
Strategy and Implementation of System Performance OptimizationF.J. Qu, H. Zhao and Q.B. Yuan 2276
Research of Closed-Loop Calibration Model Based on Kalman Filtering AlgorithmZ.Q. Ma, Y.Z. Cheng, S.Y. Sun and C.P. Wang 2280
Restrike Modeling of Vacuum Circuit Breaker Switching Off Shunt Capacitor Banks withEMTPY.Y. Wang, S.H. Liu, W.Z. Liu and K.Y. Wang 2287
Research on Numerical Simulation of Dynamic Pressure for Stress Sensibility Coal SeamY.H. Ding, B.H. Wang and X.Z. Yan 2293
Study of Voltage Level Sequence Based on the SE-DEA ModelQ.M. Gao and Q.Y. Zhang 2300
The Research and Analysis Based on a New Hybrid Chaotic SequencesX.S. Zhou, M. Li, Y.J. Ma and S.J. Liu 2307
Modeling and Simulation for Boost Converter Based on HDS TheoryY.J. Ma, S.J. Liu, X.S. Zhou, C.W. Tian and F. Liang 2313
A Procedure for Modeling of Holonic Control Systems for Intelligent Building (HCS-IB)R.M. Da Silva, J. Arakaki, F. Junqueira, D.J.S. Filho and P.E. Miyagi 2318
Research on GMM Background Modeling and its Covariance EstimationY.C. Zhang, R.M. Zhang and S.J. Song 2327
Study and Application of ESD Generator ModeleH. Wang and W. Tian 2334
A Method for Modeling and Simulation of Differential Drive Mobile Robot LocalizationBased on EKF Multisensor FusionB.Z. Bao, P. Yang and H.W. Cao 2339
A New Format Power Flow Computation Software Analysis and Design Based on MATLABJ. Luo and W.H. Wu 2346
A New Method for Modeling of Fully Flexible AircraftsD. Guo, M. Xu, S.L. Chen and Y. Qian 2350
Simulation Study of Variable-Frequency Speed-Regulation Vector Control System ofAsynchronous MotorB.Q. Xu and X.L. Zhang 2356
Research and Analyze on the Lightning Test of Aircraft ModelH. Wen and H. Wang 2361
Modeling of Active Flexible Suspensions by Mobility and Transfer MatrixJ.C. Niu, H.N. Guo and M. Li 2366
Advanced Materials Research Vols. 383-390 q
Simulation for Expansion of Fabrication Hydraulic Torque Converter and CorrespondingExperimental InvestigationJ.Z. Hui, Y.K. Zou, J. Cao and Z.F. Liu 2372
Modeling and Simulation of Electric-Hydraulic Clutch on Light VehicleJ.Y. Qu, D. Wang, Y.R. Zhang and G.X. Qu 2377
Study on Modeling and Simulation of Digital Factory Technology in Complex ProductionDevelopmentS. Li, Y.E. Wang, B. Chen, T. Yang and Q.L. Dong 2383
A Blackout Model Based on Optimal Risk Index and High-Risk Line IdentificationX.Y. Ding and X.D. Liu 2390
Computational Model for Machine Vision Inspection Based on Vision AttentionJ.F. Shi, Z.W. Su and G.H. Li 2398
Fuzzy Based Model Predictive Control for Uncertain Nonlinear SystemL. Xu and F. Liu 2404
Temperature Simulation on Rotor and Stator of Hydro-GeneratorQ.F. Zhang, H.M. Cui, J.L. Yan, M. Wang and Z.X. Chen 2411
Output Feedback Adaptive Maneuvering for Nonlinear MIMO Systems with HighFrequency Gain Matrix HurwitzY. Zhou and Q. Zang 2417
The Operating Point Determination of Special Turbine in Cooling TowerY.P. Li, Y. Ren and G.F. Yue 2423
Aircraft Landing Gear of a Dynamic Research and Computer SimulationS.S. Li, X.M. Liu, Z.G. Zhu and F. Yang 2426
Research on the Pollution Diffusion Regularity near Sewage Outlet Areas in YunchengReach of the Fen RiverJ.H. Hou, M.Q. Feng, X.P. Xing and Z.H. Hou 2430
Numerical Aperture and Partial Coherence Optimization in Optical Li-Thography underOff-Axis IlluminationL.P. Guo, S.G. Fu and X.J. Liu 2437
Lack of Oil of Oil-Paper Capacitive Bushing Damage and its Judging MethodsT.S. Wang 2443
Study on Improving Power System Damping Characteristic in Novel Excitation SystemP.H. Yang, G.M. Cui and W.Y. Liu 2447
A Simple Method of ABS Optimal Slip Ratio IdentificationL. Zhao and L. Tang 2453
Rotor Speed and Stator Resistance Identification of Direct Torque Control for InductionMotor Based on Mutual MRASZ.T. She, J.B. Yuan, Y. Zheng and Y.J. Peng 2458
Numerical Modeling and Solution of Ground Water Inrush at the Baixiangshan Iron MineD. Wu, S.J. Cai and W.X. Wang 2464
Study on Regulating Reservoir Changing Water Resource Value MechanismZ.Z. Zhang, J.X. Xu, Y.B. Li, Q.Q. Qi and Q. Huang 2471
The Research of Traveling Wave Fault-Location Methods for the 10kv DistributionNetworksQ.L. Ding, Z.D. Yang and R.J. Xu 2479
Computer Data Structure for Geological Entities Modelling Based on OO-Solid ModelJ. Fan 2484
Research on the Efficiency Evaluation Model of Fire Command Automation SystemL.M. Zhang 2492
A New Method for Faulted Line Identification in Neutral Non-Grounded DistributionSystemsD. Li and F.Z. Wang 2496
The Simulation of Pitch Control System for Variable Speed Wind Turbine Based on NeuralNetworkL.N. Liu, H.J. Qi and B. Li 2501
Design of Li-Ion Batteries Equalization Module of Electric VehicleZ.X. Li, F. Yu and M. Li 2507
r Manufacturing Science and Technology
System Stability Improvement of DG Connected to the Grid Based on Power Conversionand Energy Storage SystemH.H. Kuang, Z.Q. Wu and X.N. He 2513
The Remote Warning and Diagnosis System for CNC Machine ToolsZ.R. Chen and Y.F. Li 2518
Finite State Machine to Optimize Multi-Tasking Concurrence Technology for Real TimeOperating SystemL. Zhu and Z.G. Wu 2522
The Simulation Design of Spatial Arc Cam Numerical Control MachingG.G. Zhang, Z.B. Chang, Q.S. Gong and C. Liang 2528
Model Designing and Simulation Realization of ARC Protection System Based on GOOSED.J. Li and Y.S. Wang 2533
Information Model of ARC Protection System Based on IEC 61850D.J. Li and Y. Zhang 2540
Study on Pilot Performance ModelW. Liu, C.K. Liu, D.M. Zhuang, Z.Q. Liu and X.G. Yuan 2545
The Principle and System Design of Self-Cleaning FilterW.S. Liu and Z.Q. Huang 2550
Comparison of Expert and Novice Eye Movement Behaviors during Landing FlightW. Liu, C.K. Liu, D.M. Zhuang, Z.Q. Liu and X.G. Yuan 2556
A Device Reactive Capability Assessment Model Based on Improving Voltage Stability LIndicatorQ. Deng, L. Lv, J.R. Chen and X.F. Xu 2561
NURBS Interpolation Algorithm Based on Feedrate Sensitive Points IdentificationF. Lin 2567
The Performance Assessment and Optimal Design of EWMA Charts Based on AverageProduct LengthW.H. Yu 2573
Finite Element Simulation on Temperature Field Couple under Contact Resistor Thermaland Friction Thermal in Friction and WearL. Dong, H.P. Jiang and H.S. Wang 2578
A Domain Decomposition of the Finite Element-Boundary Integral Method for Scatteringby Deep CavitiesZ.W. Cui, Y.P. Han and W.J. Zhao 2585
Study and Simulation for MPPT Control of Photovoltaic Generation System Based onCombining Constant Voltage Method with Adaptive Duty Cycle Perturb MethodW.D. Yun, X.Q. Ying, Z.Y. Sheng, X.J. Ming and H.J. Xue 2590
Simulation of Islanding Detection for Photovoltaic Grid-Connected Inverters Based onPositive Feedback Intermittent Frequency DriftX.J. Ming, Z.Y. Sheng, X.Q. Ying and W.D. Yun 2596
Research on Energy-Saving Control Technology of BoilerY. Yi, G.J. Chen and J.L. Jia 2603
Fuzzy Parameters PID Control and Simulation Experiment of Permanent Magnet LinearSynchronous MotorX.Y. Qin and S. Hua 2608
A Flux Observer of Voltage-Current Model Based on PI RegulatorS.W. Fan, X.Y. Zhao, Z.X. Li and H. Zhang 2612
Analyze of Vehicle Active Rollover Control on Air SpringJ.J. Xia and C. Hu 2618
Refinement Envelope Analysis for Small Failures of Rolling BearingS.S. Zhao and J.J. Pan 2622
Research on the Influence of Zero Space Voltage Vectors on Direct Torque Control ofPMSMY.Y. Gao, M.J. Liu, D.P. Kong and Y.G. Li 2628
Research on Modeling and Control Methods of Variable-Speed Variable-Pitch WindTurbine GeneratorsN. Li, H.P. Nan, X.Y. Yu and L. Su 2636
Characteristics Analysis of a Novel Detent-Force-Based Magnetic Suspension SystemX.Z. Xu, X.F. Qin and X.D. Wang 2644
Advanced Materials Research Vols. 383-390 s
An Approach for Electrical Inter-Harmonic Analysis Based on W-H TransformG.L. Cheng and J. Lin 2649
Model Reduction of a Two-Link Rigid-Flexible Manipulator Based on SpectralApproximation MethodY. Pan and H. Deng 2654
The Simulation Research of Rotor Flux Model in Asynchronous Motor ControlB.Q. Xu and F.H. Yang 2661
The Analysis of Air Gap Flux Density in Permanent Magnet Brushless Motor with ExternalRotorR.Y. Xu and C.S. Zhang 2666
The Design of the Small Automatic Batching Machine Control SystemT. Sui, B. Li, X.Z. Liu and W.S. Xu 2672
The High-Gain Boost Converter for Maximum Power Point Tracking in PhotovoltaicSystemH.F. Tian, J.B. Cao and Z.X. Li 2677
Research on Key Technology of Airport Simulation Based on OSGK.L. Liu and D.K. Zhang 2685
Chapter 9: Composite Materials II
Synthesis and Industrial Trial of New Composite Cationic Flocculant PAFSZ.A. Liu, J.H. Hu, J.P. Chen, J.Y. Xue and Q.W. Liu 2693
Analysis on the Loading Stress, Thermal Stress and Coupling Stress in PCC-AC CompositePavementB. Yang, T.Q. Yang and G.D. Peng 2700
The New Fire Prevention Materials Using in the Coal Fire Zones-Foamed GelK. Cao, D.M. Wang and X.X. Lu 2705
Study on Stirring Brazing of SiCp/A356 Composites with the Zn27Al Filler Alloy in AirH.B. Xu, B.F. Zhou, Q.X. Luo, Y.L. Zeng and C.H. Du 2710
A Study of Structure Parameters of Block Copolymers Polystyrene-Polyethylene OxidesY.Q. Jiang, Y.B. Zhang, Z.Y. Lin, J. Chen and M.M. Yu 2714
Damping Analysis of 3D Composite Structure Embedded with Visco-Elastic LayerM.I. Sabir, E.B. Liu, W.T. Guo, Z. Li and L. Li 2719
Experimental Study of Mechanical Properties of Multiscale Carbon Fiber-Epoxy-CNTCompositesK. Sharma and M. Shukla 2723
Investigation of Mechanical Behavior of Stir Casted Al Based Composites Reinforced WithB4C NanoparticlesA. Alizadeh, E. Taheri Nassaj and M. Hajizamani 2728
Effect of Milling and B4C Nanoparticles on the Mechanical Properties of NanostructuredAluminum Composite Produced by Mechanical Milling and Hot ExtrusionE. Taheri Nassaj and A. Alizadeh 2733
Mechanical Characterization of Polypropylene Natural Fibre CompositesS.J. Muthu and R. Paskaramoorthy 2737
Energy Absorption Capability of Hybrid Tube Made by Mild Steel and GFRP under Quasi-Static LoadingR.M. Lima, Z.N. Ismarrubie, E.S. Zainudin and S.H. Tang 2741
Direct Extrusion of Circular Profiles with Surface Composite Produced by Friction StirProcessingA. Aghagol, S.M. Darani, K. Abrinia and M.K.B. Givi 2747
Influences of Tool pin Profile on Microstructure and Mechanical Properties of Al/CuComposites Fabricated via Friction Stir ProcessingA. Mostafapour Asl, S.M. Darani, M.K.B. Givi and A. Aghagol 2753
Some Investigations of Wet Sliding Behaviour of Al - SiC Particulate CompositesA. Mishra 2759
Composite Clayey Sand and Short FiberA. Chegenizadeh and H. Nikraz 2764
t Manufacturing Science and Technology
Multilayer Synthesized CuInSi Composite Film by Magnetron SputteringJ.S. Xie, P. Luan and J.H. Li 2770
Inorganic Composite Material Based on Fly Ash, Red Residue from Bauxite Ore for RoadBuilding Projects in VietnamN.V. Chanh, M. Shigeishi and T.Q. Tho 2774
Chapter 10: Materials Forming
Effect of Blank Holder Force with Low Frequency Vibration Technique in Circular-CupDeep-Drawing Using AZ31 Magnesium Alloy SheetN. Horiike, S. Yoshihara, Y. Tsuji and Y. Okude 2785
Performance of Modified Epoxy Resin by Inorganic PackingL. Zhang, W.Y. Liang, J.F. Zhang and F. Liu 2790
Characteristic Features of Thickness Change of Pipe during Die FormingY. Kotani, S. Kanai and H. Watari 2794
Austenite to Ferrite Transformation after Hot Deformation of Low Carbon SteelD. Ferdian and A. Norman 2801
Rolling Stock Times and Aluminum Profiles Extrusion Development in ChinaH.Y. Wan and Z.F. Zhou 2808
Sucking Machinery of Transport for Dosing Granulations of Plastics at Injection MoldingE. Ragan, P. Baron and J. Dobránsky 2813
An Upper Bound Analysis of the Ring Rolling ProcessA. Parvizi and K. Abrinia 2819
Review of STEP-NC Compliant System for Turn-Mill OperationsY. Yusof and M.F.M. Nor 2827
Based on Nash Optimization Decoupling Control System for Special Shape Pipe AutomaticWelding MachineW.B. Ma, K. Zhang, J.H. Liu and Y.N. Rui 2832
Research on Meshing Theory of Involute Helical Gear with AsymmetricN. Li and W. Li 2838
Research on Dynamic Characteristics of Disc BrakeF. Chen, Y.F. Hou, H.Y. Wu and H.W. Wang 2845
Analysis on the Process of Induction Heating for Shrink-Fit ChuckS.L. Wang, B. Zhou, W.Z. Zhang, Z.J. Yang and G. Liu 2850
Sensorless Control of SPMSM Based on High-Frequency Current Signal Injection in theDirect Axis at Low and Zero SpeedY. Feng, B. Zhou, Y. Liu and S. Li 2856
Finite Element Analysis of Ring-Plate Indexing Cam Mechanism Contact Stress Based onMATLAB and ANSYSY.Q. Li, M.T. Liu and G.C. Tian 2862
Resonance Analysis of Manipulators with Flexible Link and Flexible JointZ.H. Gao and Y.S. Bian 2868
Optimum Design of Movement Parameters for Soft Plastic Vibration Sorting Machine’sScreenX.H. Yang and H.X. Zhao 2875
Preload Analysis of Bolt for a Small Pneumatic CylinderW. Liu, C.L. Wang and D. Jiang 2880
Component of Clathrate Hydrates Formed in CH4-TBAB-H2O SystemL. Yang, S.S. Fan, X.M. Lang, Y.H. Wang and D.D. Bi 2883
Preparation of Expanded Perlite-Based Binary Eutectic Composite of Phase Change HeatStorage MaterialsB.Y. Zhang, C.M. Jiao, P. Wang, L. Jiang, B.H. Ji and D. Fang 2889
Study on Natural Gas Converted to C2 Hydrocarbons in Plasma StateD.W. Wang, T.C. Ma and Y.T. Zhang 2894
Chapter 11: Materials Behavior
Advanced Materials Research Vols. 383-390 u
Study on a Methane and Acetylene Spectrum Absorption Mode Gas Sensor with OpticalFiberJ.L. Wang 2903
Spectrum Absorption Methane Gas Sensor with Optical Fiber Based on FrequencyHarmonic Detection MechanismJ.L. Wang 2907
Research on Radial Inflation of Steel Tubes to Enhance the Crashworthiness of VehiclesT. Hao, H. Yang and H.B. Xu 2912
Based on the TLM Method 1000kV UHV Transmission Line Performance AnalysisF.X. Li and Y.L. Wang 2917
Experiment Study of Coal Char Combustion Characteristics Under Mixed O2/CO2X.J. Liang and W.P. Yan 2923
Research on Adaptive Rotor Flux Observer with the Speed Feedback and Rotor ResistanceDisturbingY.J. Zhang and X.Z. Li 2929
Analysis for Radiation Characteristics of Horn Antenna for Out of BandR. Kong, D.L. Su and Q.Y. Lv 2935
Fatigue Life Assessment of Crane ReelW.M. Du and F. Xue 2941
Kinetics of the Ozonation of Tetrabromobisphenol-A in WastewaterJ. Zhang, S.L. He, M.F. Hou, L.P. Wang and L.J. Tian 2945
Influence of Additive White Gaussian Noise on the Interpolation Method of DiscreteSpectrumC.Y. Xu, K. Ding, Z.J. Yang and H.B. Lin 2951
An Improved Direct Neural Network Approach to Flatness Pattern Recognition Baseed onGA-RBFX.H. Feng and X.J. Sun 2958
Analysis of Electromagnetic Field and Temperature Field of Low Speed High TorquePermanent Magnet Motor under Locked-Rotor OperationL.S. Zeng and L.Z. Sun 2963
The Characteristics of Melt Flow in Composite Spinning MicroporeX.H. Gan, Q. Liu, X.J. Ma, C.H. Jia and C.C. Yang 2968
Simulation and Dynamic Characteristics of Discharging Process of Storage Tank Used inConventional Air-ConditioningX.Y. Li, Y.Y. Wu and Z.F. Cen 2974
General Model of Optimal Control of Fully Flexible Vibrating Suspension SystemsJ.C. Niu, J.Q. Zhu and F.W. Ji 2978
Numerical Simulation of Dimethyl Ether/Air Laminar Diffusion Combustion Characteristicwith the Different Fuel Inlet Velocity and Rotate SpeedR. Chen, H. Wang and H.T. Wang 2984
The Improvement of Anti-Surge Control on Air Separation CompressorC.H. Jiang, S.Z. Lu and L.F. Liu 2991
Effects of Pressure Ports Layout on Angle of Attack and Sideslip Estimation in the FlushAir Data SystemL. Fu and Z. Luo 2996
Effects of Additive on the Desulphurization Characteristics of WastesB. Zheng and C.M. Lu 3001
Effects of Speed Ratio K Value of Rubber-Bar on Cotton Harvesting PerformanceH.W. Zhang and M. Kang 3005
Study on the Effects of Coal Blending on the Slurry Ability of Shenmu CoalsJ.Z. Liu, Y.J. Yu, J.H. Zhou, C. Du, L. Ye, J. Cheng and K.F. Cen 3011
An Experimental Study on Nitric Oxide Reduction through Coal-Biomass Blend ReburningS.L. Niu, K.H. Han and C.M. Lu 3017
Research on NDT System of Steel Bar CrackH.B. Liu, H.D. Qi, H.B. Liu and L.Z. Wang 3022
Research on the Cr (VI) Absorption by Floc-Type Biosorbent ARQ. Li, S. Han, Y.X. Wang, C.J. Ye, F.S. Wang, Q.S. Qi and H.R. Cui 3029
v Manufacturing Science and Technology
Heat Transfer and Anti-Fouling of Liquid-Solid Two-Phase Flow in Cooling Water Pipes ofStavesL. Zhang, Z.L. Ma, Q.X. Bo, L.K. Wang and L.L. Gao 3035
Temperature Calculation on Phase Lead Connecting Structures of 1100MW GeneratorStator Parallel RingsY.F. Wei, L. Qi, T.S. Wang, J.P. Wang, Z.L. Xian and R.L. Liu 3040
Study on Magnesium Alloy Sheets Deep Drawing at Gradient TemperatureA.M. Zhang, Z.Y. Zhang and Q. Li 3046
Corrosion Resistance of Fe-B Alloys Immersed in Molten Zinc BathX.M. Cao, P.F. Yin and R.N. Ma 3051
Adsorption Characteristics of Nitric Oxide and Sulfur Dioxide on Coal Activated CarbonD.J. Kang, X.L. Tang, J.H. Peng, H.H. Yi, P. Ni, Z.Q. Ye and K. Li 3056
Fiber Optic Dynamic Light Scattering SystemsC. Wang, W. Liu, J. Shen and B.X. Tan 3063
An Experimental Study on Diesel Fuel Droplets Coupling EvaporationY.P. Ma, X.R. Li, X.Y. Wang and F.S. Liu 3068
Optimal Control of the Industrial Furnace SystemX.T. Tang and C.Q. Cai 3077
The Corrosion Resistance of Zn-Plated Samples with Blackish Green Passivation FilmY.B. Cao 3081
Studying on the Propagation Behavior of Bent Crack Bending from Slant Pre-Crack withCompressive Residual StressY.L. Ma 3086
Non-Thermal Plasma Assisted Catalytic Oxidation NO over Mn-Ni-Ox Catalysts at Low-TemperatureK. Li, X.L. Tang, H.H. Yi, P. Ning, Z.Q. Ye, D.J. Kang and J.H. Song 3092
Study of XLPE Cable Materials Impurity Detecting Based on CCD TechnologyS.H. Tang 3099
Indoor Localization System Based on an Ultrasonic Sensor NetworkL. Zhang, S.L. Shi, Y.Y. Sun and Y. Tian 3105
The Study of Polymer Material Transference Phenomenon Measurement MethodD.J. Li and S.J. Wu 3110
Trace Gas Sensor Based on MEMS Cantilever ResonatorY. Dong, W. Gao and Z. You 3115
Growth Kinetics of Tetra-N-Butyl Ammonium Bromide Semiclathrate Hydrate throughConcentration Determination and Microscopic ObservationS.S. Fan, J. Du, Y.H. Wang and X.M. Lang 3121
Evaluation of Flexural Performance for Prestressed Concrete Beams with FRP TendonsJ.Y. Cai, Z.F. Tu, S.M. Gong and L. Zhuang 3128
Effect of Chitosan/Polymeric Aluminum Composite Flocculant on Activated SludgeB.T. Liu, H.Y. Song and Y.X. Li 3134
Recycling Of the Epoxy Resin of the Waste Printed Circuit Boards Using Solvent ExtractionL.Z. Ma, H. Wang, S. Qing and L.Z. Ma 3140
Effect of Coupling Agents on the Mechanical Properties of Wheat Straw Flour andPolyethylene CompositesH.Z. Cai, W.M. Yi and X.Y. Bai 3145
Comparison Experiments on Relieving Differential Settlement of Subgrade by GradedCrushed Rock in Different Particle SizesW. Liang, B. Yang, Y.L. Zhao, Y. Li and X.K. Wen 3151
The Experimental Study on Fatigue Properties of CFRP Reinforced Concrete BeamZ.Q. Li and Y.Y. Fan 3157
Materials Flow Analysis on the System of Flue Gas Desulfurization and Denitration withPyrolusite SlurryC. Qiu, W.Y. Sun, C.L. Wang and S.J. Su 3162
Study on Dispersion Behaviors of Oolitic Hematite Ultrafine Particles in WaterF.S. Niu, S.X. Liu, J.X. Zhang and Y.M. Nie 3169
Advanced Materials Research Vols. 383-390 w
The Technology and Equipments for Producing Gesso Blocks in a Wet Environment byDirectly Using Desulfurization GypsumL.C. Han and Y.C. Wang 3174
Characteristics of the SiN Uniaxial Strained NMOSFET with Channel FluorineImplantationY.Y. Chen, C.R. Hsieh and F.Y. Chiu 3178
Efficient and Stable Photocatalytic Activity of CeVO4/TiO2 Nanocrystalline Heterojunctionunder Visible Light IrradiationH.J. Huang, W.L. She and H.P. Huang 3183
Preparation of Visible-Light-Responsive TiO2-xNx Photocatalyst by a Very Simple MethodH.J. Huang, W.L. She, L.W. Yang and H.P. Huang 3188
Effect of Thickness on the Mechanical Properties of Magnesium Alloy StentM.I. Sabir, E.B. Liu, Z. Li, Y.F. Zheng and L. Li 3192
Development of Inorganic Gas Barrier Material in Solar Cell Devices for PlanarizationProperties and Sublimate Defect ReductionS. Takei 3197
Parametric Optimization of PMEDM Process with Chromium Powder Suspended Dielectricfor Minimum Surface Roughness and Maximum MRRR.K. Garg and K. Ojha 3202
Deformation Behavior in Pipe Production Process for New High Strength MicroalloyedSteelS. Moeinifar 3207
Parametric Instability of Laminated Composite Doubly Curved Shell Panels Subjected toHygrothermal EnvironmentS.K. Sahu, M.K. Rath and R. Sahoo 3212
Hot Corrosion Studies on Bimetallic Combinations of Monel 400 and AISI 304 Subjected toMolten Salt EnvironmentR.K. Devendranath, N. Arivazhagan and S. Narayanan 3217
Microstructural Characterization of Wire Electro Discharge Machined Tungsten CarbideCobalt Metal Matrix CompositeV. Muthuraman and R. Ramakrishnan 3223
High Speed Impact Characteristics of Plastic Material Based on Finite Element SimulationW.A. Siswanto, R.Y. Sharafuddin and P. Paruka 3229
Characterization of Feedstocks for Injection Molded SiCp-Reinforced Al-4.5 wt.%CuCompositeT. Udomphol, B. Inpanya and N. Chuankrerkkul 3234
Numerical Investigation of Hollow Metal Cross Section Profiles on ImpactW.A. Siswanto, B. Omar and S. Shukri 3241
Effect of TiO2 on Optical Properties of PMMA: An Optical CharacterizationG. Patel, M.B. Sureshkumar and P. Patel 3249
Variation of Optical Band Gap Width of PVA Films Doped with Aluminum IodideO.G. Abdullah and S.A. Hussen 3257
Allotropic Modification Induced by Co60 Radiation on the Structural and OpticalProperties of Aromatic PolymersS. Siddhartha, S. Aarya, A.K. Srivastava, M. Mishra and M.A. Wahab 3264
Research of Correctness on Internal Stress Measurement in Aluminum Alloy Thick PlateK. Liao and Y.X. Wu 3272
Structural and Optical Properties of Zn Doped CdTe Thin Films by Stacked ElementalLayer MethodS. Shanmugan, D. Mutharasu and K. Ibrahim 3279
Effect of the ZnO Rods Growth Time to the Conductivity of ZnO Thin Film Combined withN3 DyeE.A.G.E. Ali, W.A. Dhafina, S. Hasiah and N.A.N. Ali 3286
Effect of Barium Aluminates on Acid Resistance of Fracturing ProppantsS. Zhao, B.L. Wu, S. Qin, Y.R. Zhao and Z.S. Hu 3291
Effect of Hydrogen on the Properties of Amorphous Carbon Nitride FilmsE. Mikmeková, M. Urbánek, T. Fořt, R. Di Mundo and O. Caha 3298
Study on the Properties of Ultra High Performance Fiber Reinforced ConcreteB.P. Trinh and N.V. Chanh 3305
x Manufacturing Science and Technology
Investigating the Mechanical Properties of 0.5% Copper and 0.5% Nickel AustemperedDuctile Iron with Different Austempering ParametersB. Abdullah, S.K. Alias, A. Jaffar, F.A. Rahim and A. Ramli 3313
Deep Cryogenic Treatment on Aluminum Silicon Carbide (Al-SiC) CompositeM.S. Rasool, M.S.M. Aripin, S. Thamizhmanii, B.H. Sulaiman and D. Sathiaraj 3320
Microstructure and Friction and Wear Properties of the Composite Material of TiC/7075 inPowder MetallurgyP. Xu, H.M. Liu, X.D. Liu and F. Wang 3325
Structural and Mechanical Properties of Ti1-XAlxN Studied by Ab InitioX. Tan, Y.Q. Li, X.J. Liu and Y.H. Xie 3331
Chapter 12: Aerodynamics
Study on the Degradation of Low Molecular Organics Using Boron-Doped DiamondElectrodeF. Rong, J. Liu, L.J. Gu, D.G. Fu, Z.Z. Gu and W. Wu 3341
Properties and Sintering Mechanism of Lightweight Sludge-Flyash-Clay CeramicsM. Yue, Q.Y. Yue, Y.F. Qi, B.Y. Gao and H. Yu 3346
Technology Research on Waterworks Sludge for CeramsiteJ. He and Q.S. Wang 3352
Effect of Axial Force on Mechanical and Metallurgical Properties of Friction Stir WeldedAA6082 JointsG. Singh, K. Singh and J. Singh 3356
The Accuracy Analysis on the External Circular of Zirconia Ceramic Spindle by PrecisionMachiningF. Lu, S.C. Chen, K. Zhang and Y.H. Wu 3361
Preparation of Self-Releasing Glaze Ceramic Materials Utilizing Red MudS. Qin, B.L. Wu, S. Zhao, C.C. Ma and Z.S. Hu 3366
Chapter 13: Environmentally Sustainable Manufacturing Processes andSystems
Sustainability Index Benchmarking in a Semiconductor Manufacturing EnvironmentV. Narayanaswamy and K. Muthusamy 3377
Producing Paper Using Pineapple Leaf FiberY. Yusof, M.R. Ahmad, M.S. Wahab, M.S. Mustapa and M.S. Tahar 3382
Effect of Material Selection on the Life Cycle Assessment of Environmental ImpactC.Y. Ng and K.B. Chuah 3387
Critical Success Factors of Green Design Implementation for Malaysia Automotive IndustryN. Zakuan, M.Z.M. Saman and A.R. Hemdi 3395
Sustainability Manufacturing Assesment using PCA for Thai SME Bus Building CompaniesS. Butdee 3403
Influence of Slag and Slag Cement on the Strength of Sustainable ConcreteM.R. Karim and M.F.M. Zain 3410
Steel Slag as Neutralization-Adsorption Material for Treatment of Acidic Zn2+ - ContainingWastewaterH.F. Yang, Q.F. Ou and F. Zhou 3416
Engineering Research on ECOSUNIDE Technique for Nutrient Removal from MunicipalSewageY. Li and Y.Q. Zhang 3422
A New Method for Designing the Size of Energy-Storage Capacity in Grid-Connected WindFarmS.H. Yu and Y. Sun 3428
Effect of Low Concentration Alkali and Ultrasound Combination Pretreatment on BiogasProduction by StalkY.Z. Wang, X. Chen, Z. Wang, J.F. Zhao, T.T. Fan, D.S. Li and J.H. Wang 3434
Advanced Materials Research Vols. 383-390 y
A Solar Array Simulator Using a Buck Configuration for Small Communications SatellitesC. Salinas and Y.J. Zhou 3438
Design of Photovoltaic Generation Grid-Connected Inverter Based on DSPF. Yu, H.M. Guo and Y.H. Chu 3443
A Study of Phase-Locked Technology of Wind Power Generation Three-Phase Grid-Connected InverterS.W. Fan, C.Y. Zheng, Z.X. Li and C.X. Wen 3449
Research on Heat-Supply Energy Conservation Supervisory Controlling System in theSubstation with Peak-Shaving BoilerX.Y. Wang, S.C. Deng and W.G. Qi 3456
The Automatic Energy-Saving Control Strategy for Coal-Fired Boiler Heating SystemJ.J. Xu and Y.P. Tang 3462
CAN-Based Monitor and Control Platform for Battery Management SystemW.T. Sun, W. Liu, H.W. Sun and J.F. Gong 3466
Reliability Evaluation of Electric Power System Containing Distribution GenerationS.Y. Xu, M.Y. Chen, N. Wade and R. Li 3472
Research of Torque Control in Large-Scale Wind TurbineW. Li and J. Xu 3479
Research on Warship Intermediate Frequency Power SystemX.S. Wu and W. Gao 3486
Technique of Digital Electro Hydraulic Automatic Control of Hydro MechanicalTransmissionJ. Wang and G.L. Zhou 3493
Study on Simulation for Solar Heating System for BiogasZ.F. Liu, Y. Su and P. Zhang 3499
Modular Design of Standard Plant Based on Simulation of Architectural PhysicalEnvironmentD.D. Zhu, X.W. Zhuang, J. Sheng and Q. Ding 3505
Research on High Temperature Mechanical Properties of Casing in Complex EnvironmentDeep WellJ. Wang 3510
Simulation on Natural Ventilation in Double-Skin Curtain WallX.T. Zhu, W.Y. Huang, W.C. Yao and M.H. Xiong 3516
Analysis on the Applicability and Control Strategies of Using CO2 to Control Fresh AirT.H. Zou and F.L. Cao 3522
Study on Directly Driven Wind Turbine with Permanent Magnet Synchronous Generators(D-PMSG)Z.Y. Du and R. Ju 3528
Excitation System with Voltage Regulator for Marine-Use Brushless SynchronousGeneratorsQ.S. Ji, Y.Q. Wu and H.Y. Hao 3535
A FLC-PID Controller for Variable-Pitch System of Wind Power GenerationS.H. Li 3539
A Novel Bidirectional DC-DC Converter with Robust Control Scheme for Flywheel EnergyStorage SystemJ.Q. Yuan, Y.L. Li, B.T. Li, J. Sun and Z. Tan 3545
Study on MPPT Control of the Single-Stage Grid-Connected Photovoltaic SystemY. Wang and F.L. Tian 3552
CFD Application on Ventilation System of Hydro-GeneratorQ.F. Zhang, J.L. Yan, M. Wang and Z.X. Chen 3561
Analysis of Material and Energy Flow Variation for Energy Saving and ConsumptionReduction in Pelletizing ProcessH. Zhao and Z. Song 3566
Simulation Studies for Doubly-Fed Wind Generator Based on Neural Network InternalModel ControlJ. Liu and J.R. Chen 3571
DFIG Wind Power Generation Based on Direct Two-Stage Matrix ConverterJ.R. Wang and Y.R. Zhong 3578
z Manufacturing Science and Technology
Predatory Search Strategy for Load Distribution of Multiple Chiller Water Units for thePurpose of Energy SavingJ. Zhang and K.Y. Zhang 3586
A Method for Water Quality Remote Retrieva Based on Support Vector Regression withParameters Optimized by Genetic AlgorithmT.D. He and J.W. Li 3593
Processing Method for the Node of Wind Farm in Power Flow CalculationJ.P. Zhang, Z.J. Yan and Q.F. Ding 3598
Universal-Joint Sun Tracking Method and Tracking DeviceX.L. Xu and Y.B. Zuo 3605
A Study on the New Grid Integration Solutions of Offshore Wind FarmsX.Y. Zhang, Z.J. Wu, S.P. Hao and K. Xu 3610
The Design of SCADA System for Wind FarmZ.B. Li and W.W. Zhu 3617
Research and Evaluation on Environmental Economic Dispatch Including Wind FarmBased on Relative Entropy BalanceX.H. Zhang and Z.G. Lu 3621
Design of Solar-Wind Complementary Grid-Connected Power Generation MonitoringSystem for TeachingR.X. Sun, J.L. Wang, P.P. Huang, J. Kang, X.F. Chen and Y. Tian 3628
A Novel Algorithm for Fast and Adaptive Maximum Power Point Tracking of Wind EnergyGeneration SystemX. You, B. Zhou, G.J. Zuo and H.H. Guo 3633
Flow-Structural Coupled Finite Element Analysis of the Monopole Steel Tower under WindLoadB. Li, C. Xia, L. Xing and Z.Y. Sheng 3639
Dynamic Energy of a Large Scale Transmission Tower Subjected to Wind ExcitationsB. Li, B. Chen and C. Xia 3645
Design of the Oil Well Multi-Parameter Monitoring SystemM. Wang, L. Liang, K. Chen and N. Wang 3652
Analytical Study on Wind-Induced Vibration of Ice Coating Transmission Line SystemsJ.Q. Chen and W. Wang 3657
Impact of Plane Heterogeneity of Sandstone’s Thickness on Water Flooding EffectivenessY.G. Qu and Y.T. Liu 3663
A Novel Protection of Transmission Lines for Two ±500kV HVDC Systems Erected on thesame TowerM. Huang, G. Wang, H.H. Luo and Y.S. Liang 3669
Study on Nitrate-Impregnated Sulfur Dioxide Sorbent Derived from Sewage SludgeY.L. Li, J. Tian, W.J. Liang, H. He and Y.Q. Jin 3675
Study on the Effect of Leaching as of Phosphogypsum on the Soil EnvironmentL.Z. Ma, H. Wang, S. Qing and F.L. Ma 3681
Variational Data Assimilation for Renewable Wind Energy Predictions: China InnerMongolia Case StudyH.F. Wang, W.J. Yin, M. Zhang and J. Dong 3685
Environmental Impact of Waste Slurry in Pile Foundation Construction of High-SpeedRailway Bridges and its CountermeasuresY.L. He and C.M. Xiong 3690
Research on Wet-Chemical Deformation of Roadbed Built with Weathered StoneC.Q. Hou, X.M. Wang and L.Y. Yang 3695
Spatial Structure of Danwei Compound towards Low-Carbon - Case Study of SpaceChange in HUSTJ.F. Chen, X.Y. Zhu and L.J. Ren 3700
Advanced Wastewater Treatment under Different Dissolved Oxygen Conditions in anInnovative Step-Feed ProcessL.M. Yuan, C.Y. Zhang, R. Yan, G.Z. Zhao, L.J. Tian, Z.X. He, H. Liu and Y.Q. Zhang 3707
Application of 3d Time Domain Method for Seismic Soil-Structure Interaction Analysis ofSpatial Grid StructureH.S. Li and Y. Ding 3713
Advanced Materials Research Vols. 383-390 aa
Differential Absorbance Spectroscopy in Studying Natural Organic Matter Reactivity inDisinfection By-Products Formation: Comparison and ApplicabilityY.F. Liu, Q.S. Wang, S.C. Yue and S.S. Li 3719
Allelopathic Effect of Typha Angustifolia L. on PhytoplanktonT.T. Zhang, W. Hu and D. Zhang 3724
Study of the Treatment of Coking Wastewater by Biological Nitrogen Removal withPhysical-Chemical ProcessY.E. Ba and Z.F. Li 3729
The Analysis and Applying of Industrial Enterprises Contaminative Source Based onSuperMap GISM.T. Ma, Y.Y. Zhang and M.M. Lu 3734
Influence of Decrease in Water Saturation of Host Rocks with Dehydration Reactions on theReconstruction of the Thermal Evolution of Igneous-Intrusion-Bearing BasinsD.Y. Wang, Y.C. Song, Y. Liu, Y. Zhang, T. Qi, M.L. Zhao and W.H. Lam 3739
Edaphic Characterization, Water and Salt Translocation in Saline Marsh at Local Scale inSongnein Plain, Northeast ChinaY.J. Wang, J.M. Luo, W.F. Wang, Z.Y. Gao and S.L. Pang 3744
Empirical Study on Efficiency Evaluation of Low-Carbon Economy Transition in Resource-Based CitiesX.M. Sun and M. Zhou 3751
Ultrasound Frequency Impacts on the Removal of Indigenous Blue-Green Algae Takenfrom Lake TaihuY.J. Qiu, F. Rong, F. Yang, J.P. Li, H. Long and W. Wu 3758
Investigation of Atmospheric Mercury Pollution in GuilinJ.P. Qian, L. Zhang, Z.D. Chi, C.X. Huang, W.Y. Jiang and S.S. Chen 3763
Land Use Patterns Effect on Soil Anti-Erodibility in Low Mountain-Hilly RegionS.Q. He, Z.C. Zheng and L. Wang 3768
A Study Method of Ecological Risk Evaluation for Reclaimed WaterG.Z. Huang, Y. You, Y. Chen, J. Chang and Y.P. Gan 3775
Analyses of Impacts of China’s CO2 Emissions Factors Based on STIRPAT ModelQ. Cao, J.L. Jiao and J.L. Jin 3781
Experimental Study on Secondary Effluent Disinfection with Ultrasound and ChlorineZ.F. Li, X. Zhao, F.R. Deng, X. Jin and H. Wu 3786
Life Cycle Assessment on Resourceful Utilization System of Flue Gas Desulfurization andDenitration with Pyrolusite SlurryL. Luo, W.Y. Sun, C. Qiu, S.J. Su and H.T. Wang 3792
Dried Municiple Sewage Sludge Gasification Experiment in Dual Fluidized BedX.X. Fan, L.Z. Chu and L.G. Yang 3799
The Measures of Mine Environment Protection and Control in Qinyang, Henan ProvinceL.L. Zhang, S.L. Zhou, W.M. Mi, M.Q. Liao, K. Wang and H.D. Long 3805
The Research on Effect Factors of the Polymer Flooding in Low Permeability Reservoir ofDaqing OilfieldY.L. Wang, T. Li, Z.G. Fu, S.X. Liu, B.L. Yu and S.Y. Sun 3809
Chapter 14: Nanomaterials and Nanomanufacturing
Experimental Study of Magnetism Dependence on the Grain Size in some FerreousMagnetic NanoparticlesY.H. Zhu 3817
Silver-Coated Zinc Oxide Antibacterial Nanocomposite Preparation and CharacterizationJ.R. Li 3823
Preparation of Nickel Sulfide Thin Films and Nanocrystallites Using Nickel FurfuraldehydeThiosemicarbazone as Single-Source PrecursorA.V. Gole and S.S. Garje 3828
Effect of Hydration-Dehydration Activation on the Basic Strength of Nano StructuredAlkaline Earth Metal Calcium OxideH.M. Aziz, N.I. Masrom, N.F. Sulaiman, M.K.A.A. Mustajab and A.R. Yacob 3835
bb Manufacturing Science and Technology
Calculation of Fundamental Mechanical Properties of Single Walled Carbon NanotubeUsing Non-Local ElasticityK.K. Saxena, V. Srivastava and K. Sharma 3840
Effect of Nano-Silica on Flexural Properties of Epoxy ResinF. Liu, Z.Q. Wang, W.Y. Liang and Y.W. Qu 3845
Rheological and Thermal Behaviour of High Impact Polystyrene NanocompositeA.S. AL-Ghamdi and M.Y. Ali 3849
PVA/Kaolinite Nanocomposite Hydrogels: Preparation Method and CharacterizationM. Sirousazar, M. Kokabi, A.R. Bahramian and Z.M. Hassan 3854
An Investigation toward the Nano-Crystallization of Fe55Cr18Mo7B16C4 Bulk AmorphousAlloyS. Ahmadi, H.R. Shahverdi and S.S. Saremi 3858
Interactions between E18 Rat Hippocampal Neurons and Au-Nanowire ArraysA. Islam and L. Menon 3863
Chapter 15: Coatings and Surface Engineering
A Theoretical Investigation on the Capillary Model of Lubricant PenetrationW.J. Zheng, H.J. Pei, G.C. Wang and C.G. Shen 3871
Experimental Study of Failure Performances of 51306-Coated Bearings under LubricantInterruption ConditionL. Lu and Y.L. Yang 3876
Wellbore Stability Analysis of Coal Seam Based on Hoek-Brown CriterionH.L. Yang, Z.I. Tian, L.S. Zhang and X.Z. Yan 3882
Design of Methane Polymerization Reactor Temperature Monitoring SystemR.X. Sun, J. Kang, P.P. Huang, Y. Tian, X.F. Chen and L. Gao 3889
Finite Element Analysis on Stress and Strain of Nickel Electroless Plated Fiber BraggGratingJ.F. Xie 3893
Numerical Simulation of Multi-Pass Welding Distortion in Membrane Water-WallX. Zhang, S.L. Tu, G.X. Tao and Z.F. Zhao 3898
Research and Realization of Heating Furnace Temperature Control System Based onPIDNNH.X. Tian, P.L. Jiang and L.X. Tian 3904
Primary Study on Overtopping Erosion of Non-Viscous Embankment and Assessment ofDischarge through BreachM.H. Yu and Y.J. Liang 3909
The Formation Process of Transition Layer of Steel Wire Hot-Dipped Galfan by SendzimirProcessJ.J. Wu, K. Li and Y.Z. Fan 3917
A Novel Thermal Insulation, Sound Absorption and Decoration MaterialH.B. Zhu, P.M. Wang, C.S. Wang, G.T. Yan, Y.S. Cheng and L.M. Wu 3922
Properties of Iron Tailing Coatings on Stainless Steel SubstrateS.X. Liu, Q.P. Wang and Y.M. Nie 3929
Erosion-Behaviors of the Steel Structure Coating Eroded at Low Erosion-Angle inSandstorm EnvironmentY.H. Hao, Y.M. Xing and L. Li 3933
Comparison on the Adsorption Thermodynamics of Three Typical PetroleumHydrocarbons in the Single and Mixed Solution on Aquifer MediaY. Qin, Y. Xiong, C.L. Kang, J.R. Wang, H.F. Liu, C. He and X.Y. Lin 3939
Bioactive Coating on Stainless Steel 316 L through Sol-Gel MethodS. Jafari, M.M. Taheri and J. Idris 3944
The Effect of Protective Coatings on the Oxidation Behavior of 6061Al/SiC Composite atHigh TemperaturesN.K. Udayashankar, S. Rajasekaran and J. Nayak 3949
Improvement of Surface Roughness of Al-Si Alloy Cast Strip by Vertical Melt Drag ProcessS. Nishida, K. Fukudome, H. Furusawa, M. Motomura and H. Watari 3954
Advanced Materials Research Vols. 383-390 cc
Chapter 16: Biomedical Manufacturing
A Numerical Study on the Characteristics of How Heat and Cooling Transfer on theLeading Edge of a Film-Cooling BladeS.H. Li, L.M. Du, W.H. Dong and L. Zhang 3963
Removal of Neutral Red from Aqueous Solution by Pretreated Penicillium SpL.F. Zhang and M. Wang 3969
Research on the Mechanical Properties for Medical Stainless SteelM. Wen, W. Li and X.M. Cao 3976
Design and Construction of a Yeast Gene Bayesian Regulatory NetworkM.C. Zhou and F. Zhu 3980
Research on Conditions of Producing Cellulose by Mixed Fermentation for BioethanolX.P. Su, D.C. Gong, X. Li and G.H. Chen 3986
Experimental Study of Biological H2S Removal in BiogasX.L. Fan, Z.F. Li, T.T. Wang, X. Jin and F.B. Yin 3992
The Research on Dissolving Properties of Biodegradable Cellulose PulpC. Qian 3998
Predict Interactions between Protein Residues for Developing Antibody TherapeuticsW.L. Shu and C.H. Lee 4003
Experimental Study on Enhanced Denitrification of Microbial and Steel Fuel CellK.P. Cui, X.Y. Cao and S. Jin 4007
New Type of Distributed Biomass Combustion Device Necessity and Feasibility in ChinaC.L. Pang, L. Chen and R.J. Dong 4013
Effects of Indigenous and Exogenous Microbial Inocula on Dynamic Changes of EnzymeActivities during Composting in a BioreactorZ. Xu, F.B. Zhang, L.L. Zhang and J. Li 4017
Measurements of Final Volatiles Yield of Biomass Devolatization at Flash Heating RateL.H. Wang, W.M. Yi, X.Y. Bai, Y.J. Li and H.Z. Cai 4024
Affect of Assimilable Organic Carbon (AOC) and Phosphorus to Heterotrophic MicrobialGrowth in Drinking Water Distribution SystemD.L. Jiang, G.W. Ni, Y.H. Chen and Q.J. Zhu 4031
Utilization Biomass from Bagasse Ash for Phillipsite Zeolite SynthesisW. Patcharin, K. Sriamporn and A. Kanokkan 4038
A Critical Analysis on Efficacy of Clinical Decision Support Systems in Health CareDomainM. Raza Perwez, N. Ahmad, M. Sajid Javaid and M.E. ul Haq 4043
Marginal Adaptation of Cast Metallic Dental Crowns Using Microplasma WeldingProceduresL. Sandu, S. Porojan and F. Topală 4051
Visual Evaluation of Cast Dental Alloys Welds Discontinuities in the Field of FixedProsthodonticsS. Porojan, L. Sandu and F. Topală 4058
Fabrication and Characterization of Injectable Biomaterials for Biomedical ApplicationsA. Champa Jayasuriya, K.J. Mauch and N.A. Ebraheim 4065
Chapter 17: Manufacturing Process Planning and Scheduling
Manufacturing of Multifunctional Nanocrystalline ZnO Thin FilmsA.H. Jayatissa, A.M. Soleimanpour and Y. Hao 4073
Faults Evaluation Method Based Fuzzy Theory in Distribution SystemT.S. Wang 4079
Research on Photovoltaic Grid-Connected Generation SystemS.Y. Yang, L.H. Wu and Z.X. Liu 4084
The Research and Development of NTC Automatic Tool Selection Based on AucolC.Q. Deng and B. Li 4090
dd Manufacturing Science and Technology
Study on the Power Control Method of a Stand-Alone Wind Energy System Based on DSEGJ.F. Sun, B. Zhou, H.H. Guo and G.J. Zuo 4096
The Design of the Supervisory System Based on the SOPCM. Zhang 4103
Parallel Best Neighborhood Matching Algorithm on PC Cluter PlatformY.Y. Zhang and L.Q. He 4109
Research of Roll-Isolated Gimbal Platform and a Two-Position Initial Alignment Scheme ofSINS in Spinning ProjectileY.S. Shi, B. Wang, M.J. Dong and Z.F. Gao 4115
Power-Fail Detection and Data Storage Design for Control SystemL.M. Wang and B. Mo 4121
A PSO Weighted Estimating the Mean Downstream Demand to Mitigate the BullwhipEffect in a Supply ChainL.T. Tseng 4125
Rough Sets Based Simplified Analysis of Energy Loss Indicators in Power PlantS.F. Tian, W. Wang, Y.F. Tian and S.B. Liu 4130
Modeling of Fuel Supply for Ethanol-Gasoline Engine Based on Fuzzy PID ControlW.B. Feng, X.H. Wang and R.G. Liang 4134
Cooperative Area Coverage Reconnaissance Method for Multi-UAV SystemG.Q. Long and X.P. Zhu 4141
A Research on Ultrasonic Range Finder Based on Encoding TechnologyY. Qiu and A.L. Gao 4147
The Control Strategy Of V2G Participating in Peak Regulation in Power SystemW.Q. Tian, J.H. He, J.C. Jiang and C.G. Du 4151
Geometric Distortion Correction of Geothermal Field Hyperspectral Remote SensingImages in Lintong, ShanxiX.H. Zhou 4158
The Case Study for Diversity in Nuclear Plant Instrument and Control SystemT. Fang, J.S. Hu, D.G. Lu and Z.Y. Liu 4163
Adaptive Full State Hybrid Function Projective Lag Synchronization in ChaoticContinuous-Time SystemH.L. Xi, S.M. Yu and H.L. Xi 4169
Canal Reach Deformation Monitoring Technology Based on Terrestrial LIDAR ScanningTechnologyJ. Liang, X.Q. Han, B. Hu and Y. Tan 4175
Applying Skill Technology to Aid Cadence Allegro Part ManagementH.C. Zheng 4180
Research on Fuzzy Control System of the Water Level for Steam GeneratorY.S. Zhang and Y.Y. Ma 4184
Feedback Synchronization of Uncertain Chen Chaotic SystemD.X. Wang and B.X. Mao 4189
The Multi-Humiture Monitoring System for General StorehousesR.F. Zong, J.M. Tian and J.S. Fan 4194
Transient Model of Short Circuit Fault on Subway Traction Power Supply SystemX.Q. Li 4199
Vibration Characteristic Analysis of Hoist Cage Excited by Steelwork DefectsZ.F. Li, X.M. Xiao and C. Ma 4206
SINS Installation Error Calibration Based on Multi-Position CombinationsZ.H. Wang, X.J. Chen and Q.S. Zeng 4213
Investigation of G4-73 Centrifugal Fan Airfoil Stall CharacteristicsS.L. Wang, Z. Liu and L. Zhang 4221
Hand Flat Knitting Machine Speech Counter System Design - Based on Single-ChipMicrocomputerL. Kang 4227
The Leak Detection System of Air-Conditioning Pipeline Based on LabVIEWY.P. Wang, M.C. Zhu, L. Tang and S.J. Liu 4235
Traffic Engineering for Provisioning Hose Model VPNs with Delay RequirementsY.L. Liu 4241
Advanced Materials Research Vols. 383-390 ee
Automatic Control System for the Process Parameters of the Soakage Agent in Glass FiberProductionM.C. Zhu, S.L. Nie, Y.P. Wang, Y. Jiang and J. Guo 4246
Numerical Simulation Study on BF RacewayS.Y. Guo and S.L. Han 4251
Attitude Control of Spacecraft Multibody System by Optimal Nonholonomic MotionPlanningY.P. Liu 4257
Wireless Monitoring System for Mechanical Equipment Based on Multi-Agent TechnologyB. Ma, T. Chi, X.F. Ma, X.B. Meng, L.C. Hao and D. Wang 4262
Automatic Body Control Model Experimental Platform Design Based on CAN-BusB. Sun and Y.L. Hu 4269
The Study on Optimal Location of Mine Materials Distribution Center with GPSZ.L. Zhao 4274
Study on Reliability Analysis of Distributed Control System of Nuclear Power PlantH. Wang, S.H. Li, G.C. Qi and F.S. Lai 4281
Research on the Whole Process Cost Control Methods of the Chemical Piping EngineeringX.J. Jin and C.X. Lin 4286
Research on the Digital Design and Manufacture Technology in the Manufacturing ofTitanium Alloy Cranial ProsthesisY.S. Pei, J.H. Zhao, L. Wu and J.J. Xie 4294
Construct an INLP Mathematical Model to Solve the Two-Sided Assembly Line BalancingProblem of Type-3C.H. Lan and S.Y. Ma 4302
Development of the Full-Digital High Voltage Power Supply for Electronic Beam WelderS.W. Fan and Z.T. Wang 4306
The Application of Classification and Regression Trees Algorithm in the Production Data ofMounterL. Zhang and Y.L. Shang 4312
Scheduling the CAN Bus with Rate Monotonic TechniquesZ.P. Chen and Y.L. Guo 4318
The Measurement and Process of Aeroengine Inlet Total Pressure FieldX. Yang and Y. Lei 4323
A Study on Double-Stage Fuzzy Control of Drum Level in Waste Heat BoilerY.Y. Zhao, Q.J. Meng and Z. Liu 4329
Implementation and Application of Mapping between IEC61400-25 of Wind Farm and WebServicesZ.Y. Li, B. Duan and W. Yang 4336
Individual Pitch Regulation for Wind TurbineX.J. Yao and H. Li 4341
Simulation of Internal Arcing in High Voltage Switchgear Based on FluentS. Yuan, W. Wang and F. Li 4346
Modeling and Control of a Flexible Input Boost Chopper Linked to AC Drive SystemZ.Y. Chao and W.J. Fang 4352
An Intelligent Monitoring System for Agriculture Based on Zigbee Wireless SensorNetworksY.G. Lin 4358
Accurate Detecting Method for Fractional HarmonicP. Wang, B.H. Cheng and Z.B. Zhang 4365
A Nonlinear Compensation Approach for the Iron-Core Coils Based Electronic CurrentTransformersY. Xie, L.Q. Shen and J. Chen 4371
A New Practical Fault Location Algorithm for Two-Terminal Transmission LinesZ. Ma, X.N. Li and X.M. Zhang 4377
Control Limitations on Static Unstable Airframe Using Two-Loop Acceleration AutopilotJ. Wang, D.F. Lin and J.F. Fan 4385
ff Manufacturing Science and Technology
Distributed Control System of Line Reactive Power Optimization for Rural Power NetworkBased on Improved TS AlgorithmT.Y. Xu, Y.C. Zhou, D.M. Tan and Z.L. Piao 4391
A Frequency-Domain Identification Algorithm for MIMO Fractional Order Systems withTime-Delay in StateZ. Liao, C. Peng and Y. Wang 4397
Control of a Fractional-Order Arneodo SystemK. Zhang, H. Wang and H.T. Wang 4405
Similarity Laws of Distorted Model with a Movable Bed and its ValidityB.Q. Wei, H.Y. Xun, R.G. Xiao and W.Q. Meng 4413
A Novel Speed Sensorless Control of Brushless DC Motor in Position Servo SystemC.C. Chen, J.D. Wei, B. Zhou and G.S. Li 4424
Crane Mechanics Crack Growth Life Analysis Method Research Based SIF AmplitudeFittingY.T. Sun and S.M. Wang 4432
Remote Video Monitoring and Controling System Based on Web ServicesH. Lin and H.J. Lin 4439
The Research of MAC Protocol Based on Fire System for Wireless Sensor NetworksQ.H. Wang, Y.H. Ji and H.Y. Guo 4446
Dynamic Inversion Guidance Law for a Hypersonic VehicleQ.Q. Qiao and W.C. Chen 4451
An Ultra-Wideband Antenna for Mobile Handset ApplicationsW.H. Zong, X.Y. Qu, Y.X. Guo and M.X. Shao 4457
Neural Network with High-Dimension Multi-Input Layers Based on Production Controland its ApplicationJ.L. Li 4461
Research on Numerical Simulation of Gas Storage Field in Aquifer Based on Fully ImplicitMethodB.H. Wang, X.Z. Yan and X.J. Yang 4467
Electrical Energy Saving Based on Production Process Optimization for Steel EnterpriseH.N. Zhu, J.C. Shi and L.P. Liang 4475
Processing Load Signal on Wheel Loader TransmissionL. Sun and Y.C. Liu 4482
Research and Development of a Test Platform for Synthetic Performance Parameters ofLinear MotorsZ.Q. Luan, H.Y. Ji and Q.D. Yang 4486
The Development of Monitoring System in Breeding Center Based on Wireless Sensor NetP. Yang, S. Liu and M.H. Yang 4492
A New Landslide Forecast Method and its Application in an Opencast Coal MineY.B. Zhang and J.M. Yu 4499
Progresses on Production Techniques of Gas Hydrate SlurryW.J. Chen, N. Liu and J. Li 4506
Study on Upgrading and Further Usage of Glycerol from Waste WaterX.Y. Guo, B.B. Ci, S.G. Li, W. Hu, J.L. Yu and X.H. Tang 4511
A Comparison of Rotational Speed of Marine Current Power-Generation Turbine with andwithout a Speeding-up InletZ.Y. Dong, X. Zhang, L. Wang, W. Han, X.W. Yu, X.F. Yan, F. Zhu and X.P. Li 4516
Preparation of FeO Nanofluid and its Enhancing Mass Transfer PerformanceW.D. Wu, W. Sheng, Z.M. Han and R.Y. Wu 4521
Data Envelopment Analysis and Malmquist Productivity Index for Measuring GroupPerformance on Interval DataB.R. Parchikolae, G.R. Jahanshahloo and F.H. Lotf 4528
Fuzzy Available-to-Promise System Modelling under Supplier UncertaintyT. Halim and K. Muthusamy 4535
The Analysis of Natural Characteristics of Pipeline Structure Systems Based on Frequency-Domain Transfer Matrix MethodX.D. Wu, G.M. Liu and H. Chen 4541
Advanced Materials Research Vols. 383-390 gg
Study on the Repair Methods Responding to Disturbance during Production SchedulingY.Q. Zhou, P. Yang, B.Z. Li and J.G. Yang 4546
The Position and Role of MES in the CSG Information SystemQ. Li and Q.J. Zeng 4552
Mature Using and Innovation of Economic Management in Material FlowF.R. Xiong 4557
Hybrid Iterative Local Search Heuristic with a Multiple Criteria Approach for the VehicleRouting ProblemD.R.D. Sobrino, O. Moravcik, D. Caganová and P. Kostal 4560
Total Productive Maintenance - Accelerating OEE in a Manufacturing Industry LeveragingPervasive TechnologiesD.R. Kalbande and G.T. Thampi 4568
Effect of Cutting Fluid Supply Strategies on Surface Finish of Turned PartsM.N. Islam, N.H. Rafai and B.C. Heng 4576
Research on the Safety Evaluation Method of Railway Operation SystemX.M. Xiao, Y.H. Wang and Y. Ling 4585
A Review of Metaheuristic-Based Product Concept Generation SystemsM.C. Ang, A. McKay and K.W. Ng 4594
Research and Realization for the System of Coal Mine Ventilation SystemX.Y. Nie, Z.X. Li, L. Bai and G. Weng 4603
Hybrid Method for Solving Flexible Open Shop Scheduling Problem with SimulatedAnnealing Algorithm and Multi-Agent ApproachT. Witkowski, P. Antczak and A. Antczak 4612
Tackling Means for Balancing the Production LinesO.I. Amariei, C.O. Hamat, L. Coman, C. Fănică and C. Rudolf 4620
Control of Crisis Environments by the Use of WSN Structures and Based on Expert-SOAArchitectureZ.O. Ghadikolaie, S.J. Bazminabadi, S. Kalantari, Z.H. Line and S. Shamshirband 4629
An Analytical Approach to Ring Rolling Using Modified Slab AnalysisA. Parvizi, K. Abrinia and M. Hamedi 4634
Fundamental Necessities of Knowledge Management in Project Based FirmsS.M. Mortazavi 4642
Failure Prevention on Application of Flexible Printed CircuitsP. Liu, X.L. Gu, X.G. Liu and X.B. Zhao 4648
The Impact of Using Data Warehouse on Manpower Employment Decision Support SystemA.F. Alasta and M.A. Enaba 4653
Web Application for Virtual-Making of Cost Domain in Process of Civil-Project E-Management by Suggestive AlgorithmsA.R.E. Haghighi and S. Safaee 4660
Chapter 18: Joining Processes
Parametric Optimization of TIG Welding on 316L Austenitic Stainless Steel by Grey-BasedTaguchi MethodN.N. Korra and K.R. Balasubramanian 4667
Investigations on Fume Formation Rate in Shielded Metal Arc Welding Process UsingDifferent ElectrodesM.S. Hameed, S.P. Sivapirakasam, K.R. Balasubramanian and R. Nagalakshmi 4672
Corrosion Behaviour of Electron Beam Welded AISI 304 and AISI 4140N. Arivazhagan, S. Narayanan, S. Surendra, P. Satya and G.M. Reddy 4678
Influence of Intermetallics Modification by Melt-Shearing Treatment on MechanicalProperties of Iron-Containing Al-Si-Mg Casting AlloyB.H. Kim, S.H. Lee and S.M. Lee 4683
Hot Corrosion Studies on GTA Welded AISI 304, Monel 400 Subjected to Air Oxidationand Molten Salt EnvironmentR.K. Devendranath, N. Arivazhagan and S. Narayanan 4688
Development of Defect Free Monel 400 Welds for Marine ApplicationR.K. Devendranath, N. Arivazhagan, S. Narayanan, M. Narayanan, A. Mondody and R. Kashyap 4693
hh Manufacturing Science and Technology
Effect of Electrode Coatings on Diffusible Hydrogen Content, Hardness andMicrostructures of the Ferritic Heat Affected Zones in Bimetallic WeldsD. Bhandari, R. Chhibber and N. Arora 4697
Design and Simulation of Infrared Absorption Based on Hydrogenated Amorphous SiliconThin FilmJ.W. Fu, W. Li, M.Y. Wu, M. He and Y.D. Jiang 4702
Modeling and Simulation of a Vehicle Equipped with Power Split Automatic TransmissionQ.Y. Zhang 4708
Chapter 19: Modeling, Analysis and Simulation of ManufacturingProcesses II
Multi-Objective Optimization Analysis of Motor Cooling System in Articulated DumpTruckY. Zhang, Y.H. Shen and W.M. Zhang 4715
Reactive Power Optimization Based on Improved Particle Swarm Optimization AlgorithmConsidering Voltage QualityY.P. Zhu, Z.X. Cai, Y.J. Zhang, Y.C. Song and Y.G. Yang 4721
Thermal Analysis and Test for a High Speed PM Machine for Fan ApplicationJ.Q. Wang and F.X. Wang 4727
A Load Shedding Scheme for Long Term Voltage Stability Enhancement by Multi-StageModel Predictive ControlY. He, J. Zhang, Z.W. Peng and Z.Y. Dong 4735
The Design of Data Transmission for New Intelligent Layered Water Injection Regulatingand Testing SystemG.R. Wang, M. Zhao and C.J. Huang 4742
Vibration Reducing Analysis of Beam String Structure with Seismic Isolation BearingsY.J. Nie and T.Y. Li 4748
Noise Reduction Using Wavelet Transform in Ultrasonic Flaw Detection of Small-DiameterSteel Pipe with Thick WallS.J. Wang, L. Hou, Y.L. Wang and J.Q. Zhang 4755
Analysis and Optimization Design of Self Magnetic-Suspension Permanent Magnet LinearSynchronous MotorW. Zhang, Y.P. Lan and F.G. Zhang 4762
An Improved Particle Swarm Optimization Approach for Temperature Control in HVACfor the Purpose of Energy SavingJ. Zhang and K.Y. Zhang 4768
Analysis of Precision Reliability for CX Series of Five-Axis Turning-Milling CenterJ.S. Gao, W.W. Yang, D.P. Liu, Y.P. Wang and A.Q. Zhang 4775
Orthogonal Experimental Design Applied in Analyzing Factors Influencing on HeatTransfer Performance of Engine Cylinder HeadP. Zhang, G.Y. Ouyang and J.M. Lv 4783
The Turbine Machine Fault Prediction Based on Kernel Principal Component AnalysisL.H. Lin, J. Ma and X.L. Xu 4787
Research on SSO Caused by HVDC Based on Eigenvalue AnalysisD. Zhang, X.N. Xiao, L. Yang and B.F. Gao 4792
Vehicle Model Recognition Based on Fuzzy Pattern Recognition MethodY.Q. Wang, R.J. Huang, T.Y. Xu and K.H. Tang 4799
Structure and Finite Element Analysis for a Permanent Magnet Bias Axial MagneticBearingX.S. Zhao, Z.Q. Deng, B. Wang and C. Hua 4803
Glare Prediction Method Based on SPEOS Simulation for Civil Airplane Flight DeckZ. Ma, W. Zhang, J.H. Yu and B.F. Li 4810
Automatic Position Dependent Simulation for Robust Smart GridF. Gao 4816
Analysis and Research on Optimization of Multi-Threading Load Balance under Multi-Core Architecture Based on OpenMPH. Zhao, Q.B. Yuan, F.J. Qu and H.J. Wang 4822
Advanced Materials Research Vols. 383-390 ii
Study on Dynamical Modeling of the Rolling Mill Vertical SystemX.J. Shi, D.P. Wu and Z.Y. Gao 4825
Development and Realization of Air Flow On-Line Monitoring System in Utility BoilerBased on AC InductionZ.M. Xue 4831
Distributed Contact Model for Indeterminate Grasp Force Analysis towards Heavy-DutyManipulationJ.C. Mao and W.Y. Yang 4837
Numerical Simulation of Low-Current Vacuum Arc PlasmaP. Sun and R.N. Yan 4843
Research on the Energy Efficiency Test System of the Induction MotorY. Fan, H.G. Yan, L.M. Jiang and X. Zhang 4848
Skew and End-Teeth Optimization in Reduce Permanent-Magnet Linear SynchronousMotor Normal Force FluctuationJ.K. Xia, W.Y. Li and L. Shen 4853
Precision Analysis of Simulation Systems with Hardware-in-Loop Caused by Performanceof Three-Axis Virtual Flight Motion SimulatorT. Wang, M.C. Zhu, S.L. Yin and H.G. Jia 4860
Calculation and Analysis of Electrical Field in Valve Side Winding of ConverterTransformerY.H. Gao, G.W. Liu, X.M. Liu and Z.F. Lai 4865
Chapter 20: Metrology and Measurement
The Theoretical Study and Error Analysis about On-Site Calibrating Technology of Low-Voltage Metering Device Composition ErrorH.H. Xiao and T. Chen 4873
Torque Ripple Reduction of Brushless DC Servo Motor Using Full EMF FeedbackJ.K. Xia, Y. Yuan and W. Huang 4878
A Technology of Composite Real-Time Image Processing of Profile MeasurementT.Z. Li, K.P. Hu, L. Hou, C. Jiang, H.W. Lu and X. Zhang 4884
Applied Research on the Electric Wet Effect in Optical System DesignZ.Q. Huang, P.Y. Quan and J.L. Zhang 4889
Influence of Pulsed Power Equipment’s Driving Manners on Launching Process of theElectromagnetic CoilP. Sun, B. Lei, Z.Y. Li, K.Y. Zhao and C.L. Guo 4895
Online Calculation Method of Boiler Efficiency by Oxygen Measured at a Wet BasisZ.N. Zhao, Y.Q. Ge, X.R. Zhu, C.Y. Liu, Q.F. Zhang and Z.Z. Zhao 4901
Study on Automatic Test of the High-Precision I/F ConverterM.J. Dong, B. Wang and Z.F. Gao 4906
The Research of Data Acquisition System about Flow Test in down HoleD. Feng, G.J. Xu, Y.H. Zhou, H. Zhang, X.F. Chang and L. Liu 4911
Numerical Analysis of Minicar Radiator Flow ResistanceC.B. Liu, Y.M. Mo and M. Li 4916
Wet Gas Flow Metering Based on Differential Pressure and BSS TechniquesP.X. Xu and Y.F. Geng 4922
Research on Online Monitoring of Gear Fault of Wind Power Gearbox Based onUndecimated Wavelet TransformationF.C. Zhou 4928
A Stator Flux Estimation Method Based on Duty Cycles of Inverter SwitchingY.F. Wu, Z.Q. Deng and Y. Wang 4932
Acanthopanax senticosus Harms Intelligence Quality Assessment Based on Core DataJ.Y. Lin, Y. Yu, Y.J. Xu and Z.M. Kan 4938
Fractal Analysis of Soil Profile RoughnessZ.F. Hou, Z. Chen, L. Li, J.Y. Han and Z.X. Lu 4944
Research on the Electronic Strain Piezo Gauge Based on the ShellX.E. Li and J. Zu 4949
jj Manufacturing Science and Technology
Experimental Investigation on Air-Solid Two-Phase Mixture Discharge under AC VoltageW.J. Yao, Z.H. He and H.M. Deng 4955
High-Accuracy Fundamental Frequency Detection in Power SystemL. Li, G.B. Jin, S.P. Huang and X. Peng 4962
The Design of Microwave Cavity Resonator Used for Measuring the Moisture Content inPlant LeavesJ.Q. Liu, R. Feng and W. Wang 4967
Software Development and Data Processing of Tool Wear Based on Mapping MeasurementS. Guo, C. Zhang and X.H. Liu 4971
Integration of Neural Network and Symbolic Inference and its Application to Detection ofFoundation PilesZ. Yang and H.F. Si 4977
A Traffic Flow Detection Algorithm in the Intersection Electronic Police System Based onVideoM. Yang, R.M. Liu, Q. Liu and H.Y. Zhang 4982
Measurement Technology Research on Target and Projectiles’ Miss Distance Based onDigital Image ProcessingZ.Q. Ma, S.Y. Sun, Y.Z. Cheng and C.P. Wang 4987
Prediction Method of Coal Fracture Based on Failure Approach Index and Hoek-BrownCriterionX. Wang, L.S. Zhang and X.Z. Yan 4994
An Ice-Detecting and Ice-Melting System of Electricity-Transmitting Lines Based on ZigBeeWireless CommunicationC.Y. Song, B.Q. Liu, J. Jiang and F.L. Li 5000
Fault Diagnosis Method in Controlled Rectifier Based on Support Vector MachinesH.D. Liu, W.J. Yue, H. Lan and D.H. Zhang 5006
Temperature and Humidity Measurement System for Grain Storage Based on nRF905S.L. Yang, J. Shen, Z.M. Li, B.X. Tan and K. Zhao 5012
Measurement Research on Magnetic Properties of Electrical Steel Sheet under DC BiasConditionsB.D. Bai and C. Li 5017
The Short-Term Load Forecasting Based on Rough SetZ.X. Pi, R.Z. Xu and J. Guo 5023
Fast Motion Estimation Algorithm Based on Real Time MonitoringX.M. Xu, Q. Mo, L. Ni, Q.Y. Guo and A. Li 5028
Measurement and Analysis on Power Quality of Electric Railway Traction SubstationBased on LabVIEWY.Y. Hu, H.J. Fu, J.Y. Wu, L.Y. Ji and X.L. Zhang 5034
Development of a Capacitive Displacement Sensor Based Portable Instrument with DigitalDisplay for Measuring Weld Stagger JointX.S. Ma, X. Ma and X.C. Qian 5040
A Fault Diagnosis Method Based on Improved Grey Correlation Grade for TurbineGenerator UnitC.M. Xu, H. Zhang and D.G. Peng 5045
Hand-Eye Calibration of a Robot-Based Inspection SystemA.G. Li and W.B. Wang 5050
Asynchronous Motor Bearing Fault Detection MethodsL.L. Sun and B.L. Zhang 5055
Actual Motion of 3-DOF Parallel RobotD.X. Tian and S.K. Han 5059
Influence of V/Hz Limiter on Generator in Isolated OperationR.L. Liu, W. Liu, P. Liu and Q. Dou 5066
Study on Cable-Stayed Bridge Flutter Active Control by a Single ADMS. Qi, X.X. Chen and Q. Xu 5071
Numerical Improvements to Closed-Loop Ascent GuidanceB.F. Pan and S. Tang 5076
Twelve-Position Calibrating Method without North Using for Three-Axis Magnetic SensorD. Li, S.L. Wo and X.Z. Bu 5082
Advanced Materials Research Vols. 383-390 kk
Study on SRUKF Applied in Initial Alignment with Large Misalignment Angle onStationary Base of SINSK. Cheng, C.M. Huang and Y.Y. Zhao 5088
Fault Monitoring of Transformer Based on FTIRS.B. Jiang 5094
Study on Generation of Digital Micro-Fluids Based on Surface Acoustic WaveY.Q. Wei and A.L. Zhang 5100
The Generation of Droplets with Micro-Liter Volume Using Surface Acoustic WaveA.L. Zhang and Q.J. Han 5106
Low Bit Rate Speech Coding Using Lattice Vector Quantization and Time-ScaleModificationQ. Xiao, L. Chen and C. Geng 5111
Two-Dimensional Body Untouched Measurement System Research and Developing-Basedon Sunplus SPCE3200L. Kang and S.H. Li 5117
The Design of DC Motor Excitation Regulation System Based on DSPL. Yang and J.H. Zhao 5123
A Simulation Software of Critical Sour Well Blowout Based on FLUENTQ.C. Ma and L.B. Zhang 5130
Research of Precision Injection Control System Based on the on-Line Measurement ofPolymer Melt DensityH. Xu, D.M. Wu, Q.X. Zhu and Y.J. Zhang 5136
Based on Time Series Prediction of Photovoltaic Power Plant OutputW.G. Li, Z.M. Liao and X.L. Sun 5142
Study on Piezoelectric CeramicType Insole Plantar Pressure Measurement System Based onTest PointY.M. Guo, L.M. Wang and Y.Y. Ge 5148
Research on the Type of Electrical Contact at Metal-Insulator InterfaceQ. Peng and L.R. Zhou 5154
Wavelet Analysis of Natural Annual Runoff in Dongjiang RiverJ. Li, Q.W. Chen and D.M. Li 5158
Design of Ultrasonic Gas Temperature Measurement System with Humidity Self-CorrectionM.L. Yao, Y.J. Guan and C.Y. Dong 5166
Measuring the Shielding Effectiveness of Small EnclosuresE.W. Cheng, Q.G. Wang and X. Zhou 5171
Fuzzy Controller Design Used for Steel Length MeasurementC.S. Hou 5176
Development of a 3D Vision Coordinates Measurement System Using Planar TargetQ. Fu, H. Zhao, N. Cao and J.J. Li 5182
An Instantaneous Measurement Based Transformer Protection SchemeB. Gu and J.C. Tan 5188
A Robust Feature Points Matching Algorithm in 3D Optical Measuring SystemJ.Y. Yuan, X.Y. Liu and Z.Q. Qiu 5193
Fault Position Identification for Series Compensated Lines with SSSC Based on ImprovedWavelet Packet EntropyQ. Liu, Y.Y. Chang and Y. Xu 5200
A Novel Four-Step Commutation for Bidirectional Switch Cells of AC-AC MatrixConverterY.G. Guo, P. Zeng and F. Blaabjerg 5206
Design and Experimental Analysis of Novel Refractometer Based on Photoelectric SensorTechnologyY.L. Li, Z.H. Huang and K.B. Hu 5211
Optimal Level Flight Trajectories of Stratospheric AirshipF.P. Qin and L. Chen 5216
Research on Fiber Bragg Grating Sensor Monitoring Method for Dynamical Stress ofCentrifugal Blower VaneZ.X. Hu, Y.B. Ma, S. Huan and Y.C. Zhen 5222
ll Manufacturing Science and Technology
Finite Element Analysis of Magnetic Field Modulation Effect of Brushless Doubly FedMachineX.P. Wang and F.G. Zhang 5227
Magnetic Levitation Permanent Magnet Linear Synchronous Motor ElectromagneticAnalysisY.P. Lan and C.J. Li 5233
Meshing Theory of New Epicycloids Gear DriveY.N. Xue, Y. Wang and Z. Wang 5238
Maximum Adhesion Control of Railway Based on Sliding Mode Control SystemY.F. Li, X.Y. Feng and R.K. Liu 5242
Three Parametric Model Third-Order Software Phase-Locked Loop and its Application inRange Measuring SystemX.M. Hou and Y. Wang 5250
A New Real-Time Gas Well Productivity Evaluating MethodL. Tian, Y.H. Shen, S.J. Wang and S.L. He 5257
Estimating the Threading Dislocation Density of Thick GaN FilmsR. Wang, J.L. Zhang, R.X. Yang and X.J. Zhang 5264
Analysis of Ramp Estimation Algorithms in Automatic TransmissionY.S. Tian, Z.Z. Ding, Q. Wang and B.Q. Sun 5268
Transient Combustion and Hydrocarbon Emission Characteristics of a Port-Fuel-InjectedEngineJ.H. Zhou, Y.N. Yuan, X.Q. Liu and J.Y. Du 5274
Field Analysis of Ridged Waveguides USING TRANSFER MATRIXW.H. Zong, M.X. Shao and X.Y. Qu 5280
The Software Design of a Gas-Liquid Separation and Metering SystemH.D. Shen and X.H. Xiao 5286
Acquirement of Melon Morphologies through High-Precision and Non-Destructive VisionMeasurementF.X. Lv, Y.B. Miao and Q. Zhu 5292
Study of Wireless Torque Measurement System Based on CC2500W. Liu, X.J. Song and W.G. Chen 5300
Soot Mass Flow Measurement System Using Triboelectricity and UltrasonicY.J. Zhao, X. Zhao and S.S. Yue 5304
A New Method to Measure the Transmittance of FilterS.J. Wu, D.J. Li and J.J. Lu 5309
Vibration Signal De-Noised by Alteration Wavelet Transform under Alpha StableDistribution EnvironmentQ. Xu and D.F. Zha 5315
Reliability Evaluation of Electromagnetic Flowmeter Based on Entropy Weight and FuzzyTheoryC.Y. Yu, K.L. Zhang, D.Z. Ma and Z. Zhou 5321
Traveling Wave Current Polarity Comparison Protection Using Wavelet Modulus Maximafor HVDC Transmission LinesJ.D. Duan, W. Lu and L. An 5327
The Correlation between MSCT for Lung Volume and Airway Measurements andPulmonary Function TestZ.S. Deng, R.L. Gao and F. Wang 5334
System for Detecting the Defects of Steel Tubes Based on Electromagnetic AcousticTechnologyD.Q. Shi and G.L. Gao 5339
Wind-Driven Natural Ventilation in an Areaway-Attached Basement with a Single-SidedOpening for Residential PurposesZ. Bu 5344
A Soil Sampling Method Based on Field Measurements, Remote Sensing Images andKriging TechniqueQ. Quan and B. Shen 5350
Study on the Measurement Method of Soil Surface RoughnessZ.C. Zheng and S.Q. He 5357
Advanced Materials Research Vols. 383-390 mm
Design of a Hybrid Adaptive CMAC Tracking Control for a Class of Uncertain ChaoticSystems with only Output MeasurementC.S. Chen 5363
Analysis of Drinks Base Concentration Using Microprocessor Based SensorM. Kassim, E.H.M. Saad and R. Mustakim 5369
An Innovative Drive Train Design for Improved Dead Reckoning Accuracy in AutomatedGuided VehiclesM. Muniandy and K. Muthusamy 5375
Computational Models for the Static and Dynamic Analyses of Laminated Composite PlatesS. Shantharam Patil 5381
Buckling Analysis of Functionally Graded Super Elliptical Plate Using Pb-2 Ritz MethodS.R. Jazi and F. Farhatnia 5387
A Study of the Vehicle Structure Crashworthiness in Dolly and Curb-Trip Rollover TestsC.S. Ma, J.W. Hu and J.H. Zhang 5392
A Comparative Study on Vortex Transmitter versus Differential Pressure Transmitter forFlow ControlS.H.I. Putera and M.A. Mohd Nor 5399
Developing Uniaxial Tensile Test as an Alternate Method for Thermo Mechanical ProcessEvaluationD. Priadi, R.A.M. Napitupulu and E.S. Siradj 5404
Experimental Test of Magneto-Rheological Directional Control ValveM.Y. Salloom and Z. Samad 5409
From Topological Views Observe Collision Phenomenon in F1H.W. Liu 5414
The Use of Mixture of Piper Betle and Green Tea as a Green Corrosion Inhibitor for APIX-52 Steel in Aerated 3.5 % NaCl Solution at Various Rotation RatesA. Rustandi, J.W. Soedarsono and B. Suharno 5418
Thermal Comfort Assessment in a Closed Air Conditioned ICT Laboratory at Ungku OmarPolytechnic, MalaysiaS. Singh and A. Rasdan Ismail 5426
A Study on the Effect of Different Median Barrier Shapes in Presence of Single or ParallelNoise ScreensM.R. Monazzam and S.M.B. Fard 5432
Chapter 21: Nontraditional Manufacturing
Dynamic Topology Optimization for ATP Hanging Beam of EMU Bogie Based onHyperworksC.Y. Wan, X.F. Li, J.Y. Li and Y. Liu 5441
Multi-Sensors Information Fusion Based on Momentis Method and Euclid DistanceF.Y. Lang and X.G. Li 5447
Detoxification of Wheat Straw Formic Acid Hydrolysis and Xylitol ProductionJ.P. Zhuang, L. Lin, S. Yong and C.S. Pang 5453
Image Calibration and Correction for a Fisheye LensQ.Y. Sun and P.G. Jiang 5458
Mixed-Oxide Sorbent for Moderate-Temperature Removal of Carbonyl SulfideH. Zhao, Y.N. Xu and J.Q. Liu 5464
Research on Electric Linear Compressor for New Energy VehiclesY. Shi and Z.L. Li 5470
Whole Transfer Matrix Method for the Critical Speeds of Skew Gear Transmission SystemX.Y. Gang and S. Chai 5474
Research of Replica Management Technology of Resource on Manufacturing GridX.L. Xie and J. Zhang 5479
Design of Building Heating Supply Energy-Saving Control System Based on InformationFusionG.Q. Zhang, L. Zhang, M. Wang, B. Shen, C.D. Li and Q. Yan 5484
Research on Anti-Felting Finishing Process of Wool Knitted Fabric with ProteaseH.E. Wang 5492
nn Manufacturing Science and Technology
Comparison of the Computing Method for the Radial Temperature Difference of aSupercharged Boiler Steam Drum Shell Based on the Approximate Solution and theCurrent Chinese StandardX.W. Zheng, Z. Li, H. Wang, X.H. Chen, D.Y. Zhang and X.Y. Wen 5496
The Study on Ergonomics-Based Design of Flood Survival KitL.L. Zhang, X. Wang and L. Nie 5504
Dye-Sensitized Solar Cells Based on Novel Mixed DyesT.T. Hung 5510
Soft Magnetic Composite Switched Reluctance Generator - Fabrication and AnalysisR. Karthikeyan, K. Vijayakumar and R. Arumugam 5516
Fabricating Anodic Aluminum Oxide by Anodic-OxidationJ.Y. He, J.D. Ren and Y.B. He 5522
Chapter 22: Computer-Aided Engineering in Manufacturing
Permanent Magnet Biased Bearing of Suspension SystemM. Zong, X.K. Wang and Y. Cao 5529
Heat Exchanger Optimization Analysis of Aircraft Environmental Control SystemH.B. Li, X.M. Dong, J. Guo, Y. Chen and T.T. Li 5536
The Excitation Controller for A Synchronous Generator Based on Nonlinear OptimalControlJ.L. Yang and R.C. Han 5542
RLV Attitude Control System Design in Reentry Flight PhaseP.F. Ji 5548
An Experimental Investigation of Flow Characteristics Downstream of Discrete FilmCooling Holes on Turbine Blade Leading EdgeS.H. Li, H.W. Qu, M.L. Wang and T.T. Guo 5553
Research on Rotation Vector Algorithm in Untypical Conic MotionM.J. Dong 5561
Design of Three-Dimensional Wireless Power Receiving Coil for MEMSY. Li, K.F. Xue and P. Huang 5569
Design of Control System Based on PLC for Polycrystalline Silicon Decomposition FurnaceQ. Han and Y.L. Luo 5576
Realization of Active Vibration Control on Piezoelectric Intelligent Flexible BeamD.F. Wu, L. Huang, F. Su, C.X. Liu, H.Y. Yang and A.C. Liu 5580
A Design of TRT Hydraulic Servo Controller Based on DSPY.N. Wang, X. Gao and H. Chen 5586
Field Test and Numerical Simulation of Cracks in the Box Girder of Long-Span RPCBridgesJ.M. Zhang 5592
A Novel Speed-Sensorless Suspension Decoupling Control Strategy for Bearingless MotorBased on Linear Extended State ObserverQ. Ding 5598
Study on B/S-Based Remote Fault Diagnosis System of Radar EquipmentZ.J. Sun, X.Z. Zhang, W. Sheng and S.H. Liu 5605
Turn Rate Estimation Based Adaptive IMM Algorithm for Maneuvering Target TrackingY. Tian, H. Jiang, Q.X. Ding and G.W. Liang 5609
Modeling and Simulation of Helicopter Cabin Electromagnetic EnvironmentL. Yang, Y.F. Jia and D.L. Su 5615
Tubular Permanent Magnet Linear Synchronous Motor Thrust Fluctuation OptimizationJ.H. Zhao and J.H. Zhang 5621
Kalman Filter-Based Orbit Determination with Dynamic Model Compensation for aManeuvered GEO SatelliteT.H. Xu, Y.P. Chen and Q.X. Wang 5626
A Vibration and Movement Coupled Modeling Approach of 3 DOF Flexible JointManipulatorsW. Zhuang and Y.H. Huang 5632
Advanced Materials Research Vols. 383-390 oo
Tubular Permanent Magnet Linear Synchronous Motor Thrust OptimizationJ.H. Zhao and J.H. Zhang 5640
Multi-EKF Localization Algorithm for Multi-Robots Formation NavigationY.F. Cai, Z.M. Tang and C.X. Zhao 5648
Wind Speed Prediction Model Based on Radial Basis Functional Neural NetworkT. Ding and H.F. Xiao 5656
The Design of PLC SOC Controller by Dual-Core Mutually Exclusive ProcessorL.L. Liu and P.L. Jiang 5663
Investigation of Strength in G4-73 Type Centrifugal Fan ImpellerS.L. Wang, Z. Sun and Z.R. Wu 5669
Portable Intelligent Gas Monitor System Design - Based on Sunplus SPCE061AL. Kang 5674
Finite Element Analysis of Drive Axle Housing Based on the Solid Element and the ShellElementJ.S. Fu, J.F. Wang and J. Wang 5681
Numerical Simulation of Covered Culvert at Jinan Section in South-to-North WaterDiversion ProjectX.L. Wang, Z.Y. Zhou, Y.C. Sun and T. Li 5686
Control Simulation Study Based on Recurrent Generalized Congruence Neural NetworkT.Y. Yan 5691
On Current Situation and Development of our Industrial Automation Control TechnologyJ.M. Li 5697
Cascaded Control Allocation in Overactuated Aircraft via Mixed OptimizationY. Chen, X.M. Dong, Y.L. Chen, L. Wang, J. Guo and H.B. Li 5700
Design and Research of a PMLSM-Driven Elevator Door MachineX.D. Wang, N.N. Ren and X.Z. Xu 5707
Pyramid Histograms of Orientated Gradients for Product Image RetrievalS.J. Jia, Y.P. Yang, J.Y. Zhao and N. Xiao 5712
A Review of some Intelligent Optimization Algorithms Applied to IntelligentTransportation SystemL.D. Zhang, L. Jia and W.X. Zhu 5717
Velocity Servo Design of Auto-Disturbance-Rejection Controller for Permanent-MagnetSynchronous Motor Servo System Based on Feedforward Compensation ControllerIncluding Sliding ModeJ. Bai, P. Xin and D.D. Ma 5724
Simulation of a Regenerative Braking System Producing Controlled Braking ForceJ. Hong, D.W. Zhang, G.P. Wang and N. Sui 5729
Research on the Cutting Path Planning of Shearer Based on Expert SystemJ.P. Mi, C. Tan and G.T. Quan 5738
Particle Swarm Optimization with Team Spirit Inertia WeightX.Z. Wang, Y. Li and G.H. Cheng 5744
Design of Intelligent Rehabilitation Crutch Based on AccelerometerH.C. Guo, J.B. Ma, Q.H. Zhang and J.Y. Yang 5751
Method of Controlling Inverted Pendulum Based on Fusing Genetic Algorithm and NeuralNetworkL.N. Liu and Y. Wang 5758
Research on Error-Tolerant Model of Master Control Computer for Electronic AutomationSystemS.Y. Du, X.P. Wang and T.Z. Yang 5764
Parameters Design of Main Circuit of AC Constant Voltage Power Supply Based on DualDirectional Reversible PWM ControlY.Q. Ma, L.H. Zhang, S.F. Han and Z.P. Lin 5771
CFD Simulation of Mixing Effects in Gas-Liquid-Solid Stirred ReactorJ.X. Xu, H. Wang, J.J. Wang, S.B. Wang, D.F. Zhu and G.F. Fan 5778
The Research on Application of AT-DESIGN-Based Textile CAD/CAM SystemX.L. Ren 5785
pp Manufacturing Science and Technology
Optimal Orthogonal Design for Herringbone Wells Injection and Production Parameters ofSteam Stimulation in Heavy Oil ReservoirY.T. Liu and W.H. Gu 5791
A Nonlinear Controller for PMLSM Control System Based on Tracking DifferentiatorG.Y. Yan, W. Ai and B. Chen 5796
Sliding Mode Variable Structure Control Design for a Kind of Nonlinear Discrete SingularUncertain Systems with Time-DelayY.X. Wang, C.H. Zhang and C.C. Gao 5803
An Integrated Design and Fabrication Approach for Heterogeneous ObjectsY.F. Zhu, C. Peng, J.Q. Yang and C.M. Wang 5810
Compressed Sensing Recognition Algorithm for Sonar Image Based on Non-NegativeMatrix Factorization and Adjacency Spectra FeatureY.L. Hao and L. Wang 5818
Research on Reactive Power Compensation Control System Based on Dual-CPU ModeS.J. Jiang and Y.C. Hao 5824
Optimization Design of Φ355 Automatic Feed Mechanism Based on ADAMSX.Y. Chai and X.F. Zhang 5830
Research and Implementation of Folding Machine Control System Based on MPUJ.R. Sun and J.C. Wu 5838
Optimization Problem of Maintenance Resources Allocation Based on Partical SwarmOptimizationH.Y. Wu 5844
Simulated Programming Characteristics of Stacked-Gate Flash Memories with High-kTunnel DielectricsY.Y. Chen 5851
The UML Model for Access Management System of Intelligent Warehouse Based on RFIDQ.Y. Zhu, H. Zhou, X.C. Shi and R.J. Hu 5855
Chapter 23: Meso/Micro Manufacturing Equipment and Processes
Characterisation of Microstructure, Mechanical Properties and Corrosion Behaviour onGTA Welded AISI 310 and Inconel 800B.K. Yeshwanth, S. Senthil Kumar, B. Hafeez Sharief, K. Devendranath Ramkumar, S.Narayanan and N. Arivazhagan 5863
Grain Refinement through Warm Rolling of Wedge-Shaped Low Carbon SteelR. Riastuti, R. Bastian M., D. Priadi and E.S. Siradj 5869
Design of S-Band Oscillators by Using GaAs ED02AH 0.2-μm TechnologyN.K. Najafabadi, S. Nemati and M. Dousti 5874
The Effect of Magnesium to Sulfur Ratio on the Graphite Morphology of Graphite CastIron Produced at Differrent Section ThicknessesO. Elmabrouk, O.M. Erfan and A. Kalkanli 5880
Microstructure and Toughness Properties of Subcritically, Intercritically andSupercritically Heat Affected Zones in X80 Microalloyed Pipeline SteelS. Moeinifar 5886
Fatigue Life Analysis of the Stabilizer Anti-Roll Bar Using ANSYSS.H. Liu and F. Li 5894
Research of Wind Power into the Grid Based on Large-Capacity Parallel ConverterModulesF. Ye, Z.D. Yin and C.X. Dai 5899
Investigation of a Plasma Jet Generated by High Voltage Discharge at AtmosphericPressureX.C. Li, N. Yuan and P.Y. Jia 5907
The Research of Air Purification under Complex Electric FieldsJ.H. Chen, L. Tao, P.D. Gu and Z.B. Yang 5912
Design of Mining Portable Static Resistance Strain Gauge Based on ATmega16LQ. Sun, F.Y. Guo, B. Li, F. Yin and P. Xu 5917
Design of Smart Car Servosystem Based on CameraL. Zhang and Q.H. Song 5923
Advanced Materials Research Vols. 383-390 qq
Probabilistic Harmonic Load Flow Calculation Containing Doubly Fed InductionGeneratorJ. Wu and B.C. Yan 5928
Fixed Frequency Hysteresis Control Based STATCOMJ.L. Zhang, J.Z. Li and Y.R. Zhang 5936
Parameter Identification of PMSM Based on Windowed Least Square AlgorithmS. Wang, R.J. Zhao, W.M. Chen, G.D. Li and C. Liu 5940
Research on Control System of Gearless Permanent Magnet Synchronous Traction ElevatorY. Hu, Z. Guang and X.Y. Wang 5945
Analysis of Stator Resistance Effects in Carrier Signal Injection Based Sensorless Control ofPermanent Magnet Synchronous MachineJ.M. Wang and S.X. Tian 5951
Study of Direct Torque Control Technique on High-Capacity Motor DrivesH.G. Zhao, J.W. Zhu, Y.H. Fan and X.C. Zhang 5958
Second Order Sliding Mode Control of Direct-Drive Ring Permanent Magnet TorqueMotorY.B. Sun, Y.N. Jing and J.K. Xia 5964
Fuzzy Adaptive Control of Airborne Electro-Optical Tracking Systems Based on VariableUniverseS. Gao, X.X. Xu, Q.K. Xiao and Q. Pan 5972
Series Charge-Discharge Management for LiMn2O4 Power BatteriesY.Q. Hu and H.P. Liu 5978
Wireless Power Transfer Systems via Strong Coupled Magnetic Resonances — Design, PCBImplementation and TestsY.P. Yao, H.Y. Zhang and Z. Geng 5984
The Maintenance Strategy of Electric Equipments Based on the Least Average Annual CostJ.J. Huan, B. Li, H.F. Li and G. Wang 5990
Improved Structural Design and Digital Control System for Micro-Machined Tuning ForkGyroscopeJ. Wen, X.M. Liu, Z.G. Zhu and M. Cai 5997
The Design of the Detonator Wick Resistance Auto-Stripping DetectorM.X. Yang, N. Wang and W. Song 6003
Application of Thyristor AC Voltage Regulation Technology in ICP Spectrum ExcitationSourceY.C. Zhou, R.J. Jia, R.X. Sun, P.P. Huang and Y.Q. Wang 6010
Application of Genetic Algorithm Based on Real Number Encoding to Optimization Designfor Rolling Schedule of Tandem Cold RollingX.Q. Zhao 6014
A Fridge Compressor Control System Based on MC56F8013L.H. Wang, W. Yao and W. Zhang 6019
Compound Speed Control of Ultrasonic Motor Using Two VariablesH.Y. Wang, J.Z. Shi and K. Gao 6025
Experimental Study on the Effect of Gas Composition Variation on Engine EmissionsJ.S. Guo, C.K. Qin, F. Ma and C. Tong 6031
Performance Analysis for Elliptical Tube Longitudinal Vortex GeneratorsJ.J. Zhou, X.H. Wu, X.Q. Li, J.Y. Huang and D.B. Wang 6037
Characteristic Analysis of Ceiling Radiant Heating of Capillary TubeW.B. Weng, J. Yu and T.K. Zhang 6042
Study of the Pressure Distribution between the Piston Rings in Reciprocating CompressorsD.B. Xin, J.M. Feng, Y.J. Xu and X.Y. Peng 6048
Preparation and Application on High-Efficiency Catalyst for Catalytic Wet OxidationG.J. Li, X. Zhang and L.X. Zhu 6053
An Approach for the Numerical Computation of the Reduction of the Original Porosity dueto Diagenetic and Compaction Processes in Sandstone ReserviorsD.Y. Wang, Y.C. Song, Y. Zhang, Y. Liu, M.L. Zhao, T. Qi and J.F. Zhao 6057
Influence of Packing form on Performance of Electrodeionization Process for Removal Ni2+
from Synthetic WastewaterH.X. Lu, J.Y. Wang and S.F. Bu 6061
rr Manufacturing Science and Technology
Design of a Portable Solar Photovoltaic-Driven RefrigeratorY.F. Zang, H. Zhang, S.L. Xu, Z.L. Wang and T.H. Zhang 6066
Study of Gasoline Engine Waste Heat Recovery by Organic Rankine CycleE.H. Wang, H.G. Zhang, B.Y. Fan, H. Liang and M.G. Ouyang 6071
Stability Analysis of Single-Track Railway Long Span Combination Bridge of Arch andBeamR.C. Ji, J. He and M.X. Shi 6079
Effects of Spark Advance Angle on Combustion and Emission Characteristics of aCompressed Natural Gas EngineX.N. Sun, H.G. Zhang, X. Wang, D.J. Wang, G.Y. Zheng and X.N. Sun 6085
Removal of Trivalent Chromium ION in Wastewater by Zeolite 4aL.S. Jin, X.F. Chu, G.L. Lin and B. Ying 6091
The Technique of NOx Emission Control in 1000 MW Thermal Power Unit BoilersZ.L. Wang, L. Wang, D.S. Yin and T.F. Zhang 6097
Comparative Study on Schemes of Seismic Response Reduction for the Railway ExtradosedCable-Stayed BridgeY.L. Zhang, X.C. Chen, W.J. Hou and G.D. Lv 6103
Pure Working Fluid Selection for the Organic Rankine Cycle in Waste Heat Recovery ofDiesel EngineH. Liang, X. Liu, H.G. Zhang, B. Liu, Y. Chen, Y.T. Wu and W. Wang 6110
Effects of Engine Operating Parameters on Lean Combustion Limit of Hydrogen EnhancedNatural Gas EngineX. Wang, H.G. Zhang, Y. Lei, X.L. Bai, X.N. Sun, D.J. Wang and B.F. Yao 6116
Heat Sink Matching for Thermoelectric GeneratorZ.G. Zhou, D.S. Zhu, Y.S. Huang and C. Wang 6122
Experimental Study on the Start Process for Compressed Natural Gas EngineY. Zheng, S.X. Yang, Y. Zheng and H.G. Zhang 6128
Experimental Study of Cooling Tower Packing and Deduce the New Formula of the NTUJ.B. Chen, Y.H. Shi, Y.H. Wang, H.L. Hou and D.X. Li 6134
Study on Preparation of Super Clean Coal with Selective Flocculation-Flotation Technologyon Taixi AnthraciteJ.X. Zhang, S.X. Liu, Y.M. Nie and F.S. Niu 6139
Study on Mechanism of Action of Catalysts on Liquefaction of Bagasse Alkali LigninX.J. Sui and S.B. Wu 6145
Study on Propylene Recovery in a Dispersed Absorption System-(Water-in-Oil) EmulsionSystemH.J. Liu, Y. Zhang, H. Yao and W. Zhao 6151
Design of a High Performance IMP Motor for Machine Tool ApplicationsC.C. Hwang, C.M. Chang and P.H. Tang 6156
The Research of China Solar Water Heater IndustryX.F. Guo and Y.J. Liu 6162
Emission Performance of a Diesel Engine with Pressure-Wave SuperchargerY. Lei, H.G. Zhang, D.S. Zhou and X.L. Bai 6168
Stability Analysis of Water-Based Nanofluids Prepared by Using Supersonic DispersionMethodW.D. Wu, S.M. Liu, H.X. Hong and S.X. Chen 6174
The Location Effecting of the Braces to the Lateral Displace of the Steel Frame Using theTime History Analytical MethodD.X. Gao and Z.W. Chen 6181
Pressure Forecast of an Air-Cooled Steam Condenser under Wind SpeedsW.F. He and Y.P. Dai 6187
Development and Research on a Hermetic Horizontal Oil-Injected Scroll Compressor forRecovering Casing GasX. Gao, J.M. Feng, Y.H. Shen and X.Y. Peng 6194
Experimental Research on Improvement of the Heat Pump Air-Conditioner and Hot WaterSystemJ.B. Chen, F. Li and K.W. Min 6199
Advanced Materials Research Vols. 383-390 ss
Experimental Study on Degradable Organic Wastes by Catalytic HydrothermalDegradationS.Q. Guo and X.Y. Dong 6204
Research on the Flow Character of Regenerative Heating Furnace Affected by theSwitching ModelK.C. Zheng, Z. Wen, X.L. Liu, W.F. Wu, X.L. Huang and Y.F. Wang 6210
Control Techniques for Uni-Axial Continuous Laser FabricationK.H. Yoon, K.H. Kim and J.H. Lee 6215
Chapter 24: Laser Based Manufacturing
Laser Welding Simulations of Stainless Steel Joints Using Finite Element AnalysisK.R. Balasubramanian, T. Suthakar, K. Sankaranarayanasamy and G. Buvanashekaran 6225
Effect of Peclet Number on the Thermo Capillary Convection and Molten Pool ShapeFormation during Laser Welding Using CFDT. Suthakar, K. Sankaranarayanasamy, K.R. Balasubramanian, G. Buvanashekaran and K.Krishna Murthy 6231
Heuristic Model for Dynamic Single Machine Group Scheduling in Laser Cutting Job Shopto Minimize the MakespanN.C. Ying and M.B. Mokhtar 6236
Functional Testing of Direct Metal Laser Sintered (DMLS) Components for AutomotiveApplicationC.D. Naiju, M. Adithan, P. Radhakrishnan and Y.U. Sravan 6242
An Investigation on the Effect of Pulsed Nd:YAG Laser Welding Parameters of StainlessSteel 1.4418M. Moradi, M. Ghoreishi, M.J. Torkamany, J. Sabbaghzadeh and M.J. Hamedi 6247
Evolution of Direct Selective Laser Sintering of MetalsF. Cardaropoli, F. Caiazzo and V. Sergi 6252
Effect of Defocusing on Bead-on-Plate of Ti6Al4V by Yb:YAG Disk LaserE. Mastrocinque, G. Corrado, F. Caiazzo, N. Pasquino and V. Sergi 6258
Investigation on Porosity Content in 2024 Aluminum Alloy Welding by Yb:YAG Disk LaserV. Alfieri, F. Cardaropoli, F. Caiazzo and V. Sergi 6265
Germanium-Silicon Quantum Dots Produced by Pulsed Laser Deposition for PhotovoltaicApplicationsL.H. Han, J. Wang and R.R. Liang 6270
Laser Scanner Stage Synchronization Method for Ultrafast and Wide Area FabricationK.H. Kim, K.H. Yoon, J.H. Lee, J. Suh and J.S. Kim 6277
Optical Power Optimization of the Single Mode Vertical Cavity Surface Emitting Lasers byTwo Oxide LayersM. Yazdanypoor and A. Gholami 6283
Growth and Characterization of ZnO Thin Films Grown by Pulsed Laser DepositionJ.T. He, B.X. Tan, Q.Q. Wei, Y.B. Su and S.L. Yang 6289
XPS Analysis of ZnO Thin Films Obtained by Pulsed Laser DepositionJ.T. He, B.X. Tan, Y.B. Su, S.L. Yang and Q.Q. Wei 6293
Semiconductor Lasers Based on the Orthogonal Dual Gloss MeterY.H. Gao, Y.Q. Wang, L. Hao and Y.C. Zhou 6297
Three-Photon Excitation Fluorescence Lifetime Imaging Using Time-Correlated SinglePhoton Counting MethodC.X. Sheng and H.J. Tang 6303
Research on Laser Damage to IR Guidance Anti-Ship Missile DetectorsY.W. Liu 6308
The Analysis of Turntable Error and Arithmetic Design for North-Finder Based on RateBiased RLGY. Zhang, J.L. Cao, W.Q. Wu and G.C. Hu 6313
Laser Doppler Velocimetry Signal Processing Based on Spectral Refinement and CorrectionN.L. Song, D. Zhang and Q. Li 6319
Planning Strategies for Surface Hardening by Laser RobotL.F. Liu, X.C. Yang and H.M. Zhang 6324
tt Manufacturing Science and Technology
Single-Frequency Nd:YVO4 Green Laser Using Two Brewster PlateX.J. Liu, S.G. Fu, X.L. Ge and K.Z. Han 6329
Chapter 25: Rapid Manufacturing Technologies
Study on Influencing Factors of High-Temperature Rapid Molding Product on theRehabilitation of Mold CavityL. Sun and D.L. Liu 6337
Nondestructive Testing Analysis of Reinforced Protective Cover ThicknessY.B. Jiang and W. Chen 6343
Placement Sequence Methodology in Pallet Pattern Formation in Robotic PalletisationH.A. Khan and S.H. Masood 6347
Design and Rapid Manufacturing Structural Components of a Mini-Scale UnderwaterVehicleY.L. Cheng and R.D. Chang 6352
Integrated Multi-Robotic Assembly Planning for Improved ProductivityB.B. Choudhury and B.B. Biswal 6357
Improving Equipment Effectiveness by Designing Optimal Production ProcessM.A. Okhovat, T. Nehzati, A. Pouriran, S. Fakhar and M.K.A.M. Ariffin 6363
Chapter 26: Modeling, Analysis, and Simulation of ManufacturingProcesses III
The Electromagnetic Analysis of the Magnetic Bearing Using the Finite Element MethodW.X. Jiang, L. Hou, C.R. Du and Y. Tang 6373
Numerical Simulation of Failure of Overburden in Coal Mining under ReservoirZ.C. Wang and D.S. Zhao 6378
Feasibility for the Application of the Temperature Difference Computing Method Based onthe Simplified Solution of the Radial Temperature for a Boiler Steam Drum Wall to aSupercharged BoilerX.W. Zheng, Z.Y. Wang, Z.G. Chen, Y. Sun, B. Han and X.Y. Wen 6383
Modification of Nano-Titanium Dioxide Film and Processing Experimental Study ofTannery Waste WaterP.Y. Xu, X.X. Han and S.S. Ban 6391
Study on Reliability of Structure with Energy Dissipation DampersZ.Q. Bai, W.F. Liu and H.Q. Luan 6396
Application of AHP on the System of Flue Gas Desulfurization and Denitration withPyrolusite SlurryC.L. Wang, W.Y. Sun, L. Luo and S.J. Su 6404
Absorption of Sulphur Dioxide from Flue Gas with Sodium Alkali Solution in PackedColumnsW.Z. Wang, C.G. Yang and J.R. Zhang 6409
Design of the Liquid-Cooling System for High Power LED Modules Using Taguchi AnalysisS.S. Hung, H.C. Chang and C.M. Liang 6416
Hybrid Desiccant Cooling System Using Condensing Heat as the Regeneration Source. PartI: System ModelX. Han and X. Zhang 6422
Fractal Theory’s Investigation in Pneumatic Flocculation ProcessL. Wang, Y. Li, Q.Q. Zhang and G.L. Xue 6427
Hybrid Desiccant Cooling System Using Condensing Heat as the Regeneration Source. PartII: Energy Saving PotentialX. Han and X. Zhang 6431
Experimental Study of Oil-Gas Cyclone Separator Performance in Oil-InjectionCompressor SystemX. Yang, J.M. Feng, Y.F. Chang and X.Y. Peng 6436
Study of Process Industries Strategic Environmental Assessment Matrix ModelMethodology Based on the Decision-Making IntegratedH.W. Qian and X.J. Yin 6443
Advanced Materials Research Vols. 383-390 uu
Simulation of EM Scattering from 3-D Target by MOM with Pulse Basis FunctionY.B. Miao, L.X. Guo and A.Q. Wang 6449
Numerical Simulation Research on Louver Fin in Air Conditioning for CarsJ.J. Zhou, H. Wang, D.B. Wang and K. Zhang 6463
Nonlinear Buckling Analysis of Wind Turbine TowersQ. Cao, Y. Li and H. Zhang 6469
Thermal Performance Analysis for a New External Wall Insulation SystemJ.G. Li, L.P. Tong and L.H. Tian 6476
Variable Step-Length Efficiency Optimum Control of Traveling Wave Ultrasonic MotorSystemB. Liu, J.Z. Shi and X. Liu 6484
Experiment and Simulation on Coarse Slime Recovery by Water Medium FluidizedSeparatorZ.H. Tan, Y.Q. He, Y.B. Lv, D.Q. Peng, R.C. Wu, G.P. Zhou and W.N. Xie 6490
Research and Implementation of Intelligent Control of Energy Saving and EmissionReduction in Electric BicycleY.W. Zhou and S.H. Dai 6496
The Simulation Research on the Performance of Chevron-Type Corrugated Plate HeatExchangerD.B. Wang, Z.X. Liang, J.J. Zhou and H.B. Wang 6502
Research on Structure Design and Performance Test of Electromagnetic Shielding ClothesY. Li and W.B. Zhang 6508
The Pure Heat Conversion Coefficient Analysis Method for Thermodynamic System ofAdvance Boiling Water Reactor Nuclear Power UnitZ.D. Guo and S.F. Zhang 6514
Study on the Response of Stud Shear Connectors Subjected to Different Loading RateZ.G. Mu, X.J. Li and J.B. Zhang 6519
The Resource Characteristics of Marine Gas Hydrates and the Assessment of itsExploitation TechnologyZ.G. Zhang, Y. Zhang and L.F. Gao 6523
Numerical Simulation of Air Distribution in the Series-Type Electrostatic Fabric FilterPrecipitatorM.Y. Hu, K. Che, J. Zhang and X.H. Wang 6530
Three-Dimensional Simulation of Gas-Solid Flow in the Biomass Circulating Fluidized BedGasifier’s RiserW.Y. Chen, X. Liu, X.X. Fan, L.Z. Chu, Y.M. Yang and W.T. Liu 6537
The Influence of Arrangement of Gas-Fired Radiant Heaters on Energy Saving in SubwayCoach GaragesX. Wang, H. Zhang and Y.P. Zou 6543
Experimental Study on Modified Model of Indoor Bio-Aerosol DispersionY. Ding, Z. Tian and N. Zhu 6548
Simulation and Optimization of Domestic Wastewater Nutrients Removal Process: Vfas asExternal Carbon SourceM.D. Hu, X.F. Zhou, Y.L. Zhang, M. Jiang and Y.Z. Tan 6554
The Optimization of Operation Characteristics for Finned Heat Pipe Radiator inConcentrating Photovoltaic SystemZ.L. Wang, H. Zhang and H.T. Zhang 6561
Modeling and Numerical Simulation of Dehumidifier Using LiCl Solution as the LiquidDesiccantR.P. Niu 6568
Study on Simulation Model of Hydrothermal-Treatment of Degradable Organic WastesS.Q. Guo and X.Y. Dong 6574
Modeling and Simulation of Selective Catalytic Reduction for Flue Gas Denitration inPower PlantsB.X. Shen, N. Zhao, T. Liu, F.P. Wu and C. Zuo 6580
Research on Construction Safety Evaluation Based on Fuzzy-Set Pair Analysis ModelG.Z. Huang, Z.G. Wu, C.S. Yang and H. Liu 6587
The Numerical Simulation Analysis of Excavation Process of Loess TunnelJ. Guo and Q.C. Wang 6594
vv Manufacturing Science and Technology
Performance-Based Seismic Design Approach for High Speed Railway BridgeX.C. Chen, X.S. Xia and L.L. Xing 6601
CFD Simulation and Retrofit of Natural Ventilation in a Steel WorkshopY.X. Su and X. Wan 6608
Analysis and Optimization of ORC for Low-Temperature Waste Heat Power GenerationX.L. Ma, X.R. Meng, X.L. Wei, J. Chang and H. Li 6614
The Simulation Study on Buried Ground-Source Heat Pipe Transient Temperature FieldDistributionC.S. Guan and Z. Wan 6621
Random Heat Temperature Field Model Analysis on Buried Pipe of Ground Source HeatPumpC.J. Huang, C.S. Guan and K. Xia 6626
Design and Realization of Mine Water-Inrush Visualization Simulation SystemY.D. Zhou, Z.X. Li, C.P. Li and Z.G. Cao 6632
Model Test Research on the Pile Stress by Pseudo-Static Test of Pier-Foundation-StructureSystemM.B. Ding and X.C. Chen 6641
Analyze on the Treatment Schemes and Effects of Dynamical Pressure Roadway in CoalMineL.X. Yan and A.B. Jin 6646
Dissolved Oxygen Convection and Diffusion Numerical Simulation of Water and AirMixture Flow in Circular PipeZ.G. Yin, X.W. Cao, D.S. Cheng and L. Wang 6651
Numerical Simulation on Process of Flow and Heat Transfer in Upright MagnesiumReducing FurnaceJ.X. Feng, Q.B. Cheng and S.J. Yu 6657
The Hysteretic Behavior of Fiber Beam Element Model of Reinforced Concrete forDynamic Explicit AnalysisX.H. Du, X.P. Shen and S.J. Jin 6663
Simulation of Flows Near a Groin in a Straight Open Channel with Effects of StreamlineCurvatureG.C. Sun, W.L. Wei, Y.L. Liu and G.W. Rong 6669
An Intelligent Process Model for Manufacturing System OptimizationH.K. Hoe, K. Muthusamy and H. Kanthen 6674
Neural Network Based Modeling in Wire Electric Discharge Machining of SiCp/6061Aluminum Metal Matrix CompositeP. Shandilya, P.K. Jain and N.K. Jain 6679
Kinematic Modeling and Analysis of a Multifingered Robotic HandP.K. Parida, B.B. Biswal and M.R. Khan 6684
Study of Effect of Geometry Parameters on Piezoelectric Cantilever by Modal andHarmonic AnalysisA.M. Khalatkar, V.K. Gupta and R.K. Haldkar 6689
Modeling and Optimization of Wire Electrical Discharge Machining of Cold-Work Steal2601A. Golshan, S. Gohari and A. Ayob 6695
An Optimization Model of Noise and Vibration in Passenger Car CabinA.K. Junoh, Z.M. Nopiah, W.Z.W. Muhamad, M.J.M. Nor and M.H. Fouladi 6704
Numerical and Experimental Investigation of Inward Tube Electromagnetic Forming-Electromagnetic StudyA.F. Arezoodar, H.E. Haratmeh and M. Farzin 6710
Modal Analysis of the Milling Machine Structure through FEM and Experimental TestS. Pedrammehr, H. Farrokhi, A.K.S. Rajab, S. Pakzad, M. Mahboubkhah, M.M. Ettefagh andM.H. Sadeghi 6717
Analysis of Finite Element and Finite Volume and Investigation of Effectual Parameters inDirect ExtrusionM. Maarefdoust 6722
Finite-Element Analysis of Heat Generation by Plasma in Welding Temperature Field ofStainless SteelA. Moarrefzadeh and M.R.I. Zibaei 6728
Advanced Materials Research Vols. 383-390 ww
A CAD/CAPP/CNC Integrated System Based on Lightweight 3D ModelZ.Y. Li, X.T. Tian and J.H. Geng 6735
Prelimenary Study on Thermomechanical Modelling of Cutting ProcessW.M.B. Hairudin and M.B. Awang 6741
Adaptive Aluminum Extrusion Die Design Using Case-Based Reasoning and ArtificialNeural NetworksS. Butdee 6747
Diesel Engine Maintenance System, Using Trend Analysis of Histroical Data (Case Study)A. Sayyah, M. Nikbakht, M. Sayyah, B. Btht and N. Ismail 6755
Effective Variation Analysis Model for the Riveting Press Process of a Flush RivetJ. Zhang, Y. Li, H. Cheng and K.F. Zhang 6762
Calculation of Grinding Wheel Profile and 3D Simulation for Grinding Screw Rotor FluteR.S. Lu, B. Yao, F. Li and B.S. Yao 6769
Research on 3D Modelling and Forming Simulation of Metal WireM.H. Chen, B. Yao, R.K. Lin and R.S. Lu 6776
Misfits between Manufacturing Resource Planning (MRPII) System and ManufacturingEnvironment: A Misfit-Inviability ModelS.Y. Tan, I. Rosnah and W.P. Wong 6784
Operational Framework for Manufacturing Resource Planning (MRPII) System CaseStudies in Malaysian Small and Medium Enterprises a Taxonomy Model for StructuralMisfit of MRPII SystemS.Y. Tan, R. Idrus and U.K. Yusof 6792
Artificial Neural Network Based Process Model for Arsenic Diffusion in Si1-xGex AlloysA.A. Sharma and S.S. Mane 6800
Computer Modeling of MWIR Homojunction Photodetector Based on Indium AntimonideM. Nadimi and A. Sadr 6806
Empirical Process Model for Arsenic Diffusion in Si1-x-yGexCy AlloysA.A. Sharma, S.V. Telang, A.S. Shrivastav, S.D. Shetty and S.U. Shetty 6811
The Drying Process in Spray Drying and Creation Simulation ModelI. Orlovský, M. Hatala and M. Mičko 6817
Chapter 27: Semiconductor Materials Manufacturing
Impact of Different Dose and Angle in HALO Structure for 45nm NMOS DeviceF. Salehuddin, I. Ahmad, F.A. Hamid and A. Zaharim 6827
A Study on Improving in Natural Convection Heat Transfer for Heat Sink of High PowerLEDsX.R. Meng, X.L. Ma, J.F. Lu and X.L. Wei 6834
Design and Implementation of a Multi-Channel HDLC Protocol Controller Based on FPGAY.H. Gu, W. Huang and Q.L. Yang 6840
A Low Native Jitter Voltage Controlled Oscillator on 0.18μm CMOS ProcessZ. Ma, L. Luo, Y. Guo, L.G. Xie and J.H. Chen 6846
Generation Shedding and Load Shedding Based on Transient Energy Margin SensitivityK. Zhang and L. Lin 6851
Research on MEMS Phthalocyanine-Based Gas SensorX. Liu 6856
Research on Stator Winding Leakage Reactance Calculation of Double-Winding AC-DCGeneratorX.S. Wu and W. Gao 6861
Design of Pythagorean Hodograph Curve Interpolator Based on NiosII EmbeddedProcessor and FPGAJ.J. Guo and W. Tang 6868
Research of Waveguide-Stripline-Coaxial Line Direction CouplerD.W. Shi and J. Li 6873
The Design of Single Phase AC Regulated Power Supply with PWM Chopping ControlCompensationY.Q. Ma, L.H. Zhang, S.F. Han and D.D. Song 6880
xx Manufacturing Science and Technology
H∞Control for PMLSM Suspension Platform Based on PDFFJ.K. Xia, Y.N. Wang and Y.B. Sun 6886
Vacuum Ball-CollectorJ.M. Ding 6893
Effects of Spontaneous and Piezoelectric Polarization on Spontaneous Emission Rate ofBlue LEDs on SiC SubstratesY.F. Wang 6897
High K / Metal Gate of Short-Channel SOI NMOSFET ResearchG. Lu and B. Zhao 6902
Novel Flowrate Sensor Based on a Couple of Fiber Bragg GratingsS.L. Yang, T.Z. Li, Z.M. Li, B.X. Tan and K. Zhao 6908
A LCD Touch Screen Controller Based on LPC2138J. Gao, L.Q. Zhu, Y.K. Guo and H. Meng 6914
Research on Novel Structure of Diode Clamed Multilevel StatComJ.L. Zhang, J.Z. Li and Y.Y. Wang 6920
Multivariable Distrubance Observer Based Analytical Non-Interacting Control of MineralGrinding CircuitsP. Zhou, Y.Z. Gao and T.Y. Chai 6925
Synchronization Control of Space Voltage Vector Controlled Multi-PMSM Based onAdjacent Cross-CouplingY. Zhang, H. Deng and Y. Zhang 6931
Research on Fault Diagnosis Based on AGA and LSSVMD.W. Zhang, K. Zhang and J. Jiang 6938
Study on DPC-SVM Rectifier Based on Power FeedforwardZ.F. Zhao, G.J. Tan, M. Liu, G.Z. Chen and Z. Wang 6942
PID Controll of Single Neuron for Switched Reluctance Motors Based on RBF NeuralNetworkS.F. Qi and G.D. Wang 6948
Simulation of Ultrashort Pulse Shaping Filter Based on Multilayer Volume HolographicGratingsL.P. Guo, A.M. Yan, S.G. Fu and X.J. Liu 6953
Synchronous Controller of LED Video Displays and LED Lighting CompatibleJ.S. Sun, X.N. Feng, Y.F. Sun and H. Zhao 6959
Embedded Data Acquisition System Based on LPC2290 and AD7715H. Li, H. Zhang, D.G. Peng and J.W. Wang 6964
Reliability Test and Evaluation Analysis of Silicon Pressure Sensor under Vibration StressL. Qin and A.L. Shi 6969
The Meso-Piezo-Capacitive EffectX.W. Nan and T.D. Wen 6975
Effect of Nitrogen Doping on the Structure and Optical Properties of N-Type HydrogenatedAmorphous Silicon Thin FilmsM.Y. Wu, W. Li, J.W. Fu, Y.J. Qiu and Y.D. Jiang 6980
An Improvement to Single-Phase RCD Based on MSP430W.J. Huai, Z.X. Fu and X.F. Wu 6986
Memristor Oscillators and its FPGA ImplementationA.X. Qi, C.L. Zhang and G.Y. Wang 6992
The Study of Aeroengine Automatic Starting Logical Module Oriented towardsMaintenance TrainingH. Geng and M. Wang 6998
Calculation on Thermal Field of a Doubly-Fed Induction Generator with Axial-RadialVentilation Cooling SystemZ.Q. Zhang and B.J. Ge 7004
Mechanism and Suspension Control Study for Spherical Reluctance Motor with MagneticLevitationL. Zeng, J. Wang and D. Zhang 7011
Based on CM6900 Resonance IC Controller SRC LED Lamp Driver CircuitS.H. Wei and M.J. Hou 7018
Advanced Materials Research Vols. 383-390 yy
Influence of Body Contact on the ESD Protection Performance in 0.35μm Partially-DepletedSOI Salicided CMOS TechnologyZ.F. Wang, C.M. Xie, H.J. Yue, L.S. Wu and Y.B. Liu 7025
Simulation of Silicon Solar Cell Using PC1DC. Jiang, T.Z. Li, X. Zhang and L. Hou 7032
Equivalent Circuit Model of Top-Emitting OLED for the Designing of OLED-on-SiliconMicrodisplayS.X. Zong, C.N. Li, C.H. Lv, G.H. Xie, Y. Zhao and S.Y. Liu 7037
The Industrial Research about China Solar PV Based on the Price of PolysiliconY.J. Liu and Y.Q. Liu 7043
Correlation Analysis of Polycrystalline Silicon Industry and Photovoltaic Industry in ChinaL.Y. Hu and X.F. Guo 7049
Iterative Learning Cross-Coupled Control for XY Table Based on Real-Time ContourError EstimationL.M. Wang, Q. Yang, Y.B. Sun and C.F. Liu 7054
Chapter 28: Precision Molding Processes
Analysis and Experimental Validation of Performance of Z-Source Inverter-Fed PermanentMagnet Brushless DC Motor DriveJ. Shang, Z.Z. Liu and Y. Zhang 7063
Research of Fuzzy Direct Torque Control of Permanent Magnet Synchronous Motor Basedon SimulinkY. Zhao and T.J. Li 7069
Active Disturbance Rejection Control with Self-Optimizing Control of Permanent MagnetSynchronous MotorS. Wang, M.G. Liu, Z.Y. Wang, X.N. Wu and X.G. Cui 7075
Regulator Design of Vector Control SystemY. Yang, J. Yuan and H. Zhang 7082
CMM Inspect Path Planning for Precision Convex Revolved SurfacesW.M. Pan, Y.J. Yu, W. Ma and Y.G. Liu 7090
An Axial-Flux Hybrid Excitation Flux-Switching MachineT.T. Zhu, Z.Q. Deng and Y. Wang 7094
Improvement of Passive Location Precision Using ‘Beidou’ Navigation SystemN.H. Gu and T. You 7099
Variable-Gain Cross Coupling Control for Linear Motor X-Y Table Based on GeneticAlgorithmL.M. Wang and Y. Pang 7104
Optimization of Micro-Milling Process with Genetic AlgorithmN.H. Chiu and G.T. Weigh 7111
Geometrical Error Analysis of Cold Forged AUV Propeller Blade Using OpticalMeasurement MethodA.B. Abdullah, S.M. Sapuan, Z. Samad, H.M.T. Khaleed and N.A. Aziz 7117
A Study on the Effect of V-Ring Position on the Die Roll Height in Fine Blanking for SpecialAutomobile Seat Recliner GearJ.D. Kim, H.K. Kim, Y.M. Heo and S.H. Chang 7122
Influence of Ply Angle on Failure Response of Bolted Composite JointS. Zhou, Z.Q. Wang, J.F. Zhang and Y.G. Xie 7128
The Factors Influenced to Surface Finish in Milling for Hardened Medium Carbon Steel:JIS S50CK. Jirapattarasilp, S. Kaewkuekool and W. Phongphatrawut 7133
On the Mechanism of the Effect of the Cryogenic Treatment on High Speed SteelsC. Gogte, D. Peshwe, A. Likhite and S. Lomte 7138
Research on Inorganic Material Modification of PVCC. Yang 7143
Design and Development of a Rotary Airlock Valve for Using in Continuous PyrolysisProcess to Improve PerformanceN. Somsuk, T. Wessapan and S. Teekasap 7148
zz Manufacturing Science and Technology
Acrylic-Based 1x2 Plastic Optical Fiber Coupler Device Manufacturing Using EGX400Desktop Engraver SystemA.A. Ehsan and M.K.A. Rahman 7155
The Application of Permanent Magnet Electric Machine on Electrical WheelchairX.X. Dou and Q.M. Tong 7161
Chapter 29: Nanofabrication, Nanometrology and Applications
Applications and Prospects of Hollow Micro/Nanospheres in Environmental Protection andNew EnergyX.Y. Cui, N. Zhang, P.Y. Yao and B. Liang 7169
A Design Methodology for Lithium-Ion Battery Management System and its Application toan Autonomous Underwater VehicleC. Shen and L. Wan 7175
Material Level Noise Measuring for Steel Ball Coal Mill Based on Energy Entropy ofWavelet Packet and Least Squares Support VectorZ.Y. Cai and T. Li 7183
A MEMS-Based Inertial Navigation System for Mobile Miniature RobotsM. Zhong and B. Huang 7189
Design of Photon Counter in PCS Nano-Particle Size AnalyzerX.Q. Wang, J. Shen, W. Liu and X.J. Zhu 7198
The Performance Optimization Design of High Frequency and High Voltage Transformerof Electronic Beam WelderS.W. Fan and Y. Zhao 7202
Application of Quantum-Behaved Particle Swarm Optimization in Engineering ConstrainedOptimization ProblemsD.K. Tan 7208
Nanoimprint Lithography of Multistep LoadingL. Yan, L. Yin and H.Z. Liu 7214
Influence of Surface and Interface Properties on the Electrical Conductivity of SiliconNanomembranesX.F. Zhao, P. Han, S. Scott and M.G. Lagally 7220
Chapter 30: Automation, Mechatronics and Robotics
The Design and Test of HEMP Simulator Based on Coaxial Peaking TechnologyL.S. Fan, H.G. Guo and G.H. Wei 7227
Research on Multiple Bi-Directional DC/DC Converter in Wind Power Flow Optimizationand Control SystemN.Y. Xia and Y.L. Zhao 7232
Based on Adams and Matlab Co-Simulation and Experimentation Research forIndependent 4WD EVY.Q. Zhao, R.S. Zhang, L.Y. Li and Z.J. Zhang 7238
Research on Co-Evolutionary Genetic Algorithm of Long-Distance Gas Pipelines OptimalModel EconomyL.G. Li, Y.S. Dai and J.G. Wang 7246
Simulation of NN-Based MRAC for PMSM in AC Drive Mining TruckY. Li, X.L. Zhao, F. Ma and Y.T. Wang 7251
Based on Linear Quadratic Regulator Optimal Control of Single Inverted PendulumSystem Co-Simulation of ADAMS and SIMULINKZ.Y. Xu and X.D. Huang 7258
Modeling and Simulation Research on the Maintenance System of Armored EquipmentY. Zhang, H.W. Yang and S.F. Wang 7265
The Simulation of New Arc Welding Power Based on MatlabG. Zhao and C. Shan 7270
Comparison of Photovoltaic Power Generation Interconnection StandardsJ.D. Wang, X.J. Zhang and X.H. Du 7276
Advanced Materials Research Vols. 383-390 aaa
The Design of CAN Bus Intelligence Node Based on MCF52234G.H. Li, C. Zhang and J. Tian 7282
Study on Nonlinear Robust Control for Permanent Magnet Linear Servo SystemY.P. Lan, H.X. Lan and H. Zhao 7287
Speed Sensorless Control System of Mining Locomotive Drive Based on DSPJ. Zong, Y. Ruan, Z.K. Li, L.B. Xu and B.Y. Ye 7294
A Novel Multi-Tooth Fault-Tolerant Flux-Switching MachineY. Wang, Z.Q. Deng and X.L. Wang 7300
A Novel 12/10 Electrical Excitation Flux-Switching MachineY. Wang, Z.Q. Deng and X.L. Wang 7306
Research of Engine Piston Pin Fatigue Analysis Based on UGH.P. Liu and H.Y. Wang 7312
The Study and Simulation of Pitch Control Servo System in Mega-Watt Class WindTurbineH. Zhao and H.Q. Jiang 7316
Direct Torque Control of Bearingless Induction Motor Using Space Vector Pulse WidthModulation Based on Fuzzy Adaptive ControlL.F. Wan, X.X. Liu, Z.Q. Wang and J.W. Zhou 7321
The Simulation Study for Auto Electrical Seat Controller Based on Fuzzy ControlTechnologyL.J. Zhang and G.J. Wang 7328
Study on Simulation of Path Plan of Parallel Grinding for Wedge AsphericC. Jiang, Y.B. Guo, N.N. Zhang and C.G. Han 7332
Fuzzy Control of Automobile ECBS on Varying PavementR.Y. Sun, B. Wang and Y.F. Zhan 7338
Fuzzy Controller Design for Multi-Legged RobotZ.Y. Tang, H.X. Zhong, Z.C. Pei and Y.H. Bu 7345
Development of Service Platform for Machine Tool Fixture Design and ManufactureB.P. Xiang 7351
The Modeling and Simulation of EGCS Based on Matlab/SimulinkK. Han, X.Y. Feng, X.Y. Yu and C.L. Xiong 7356
Simulation Study of Damage Identification Method Based on Lamb Wave Scattering inAluminium PlateZ.H. Tian, H.Y. Li and H. Xu 7362
Modeling and Dynamic Characteristic of a Pneumatic Solenoid ValveX.W. Pan, M. Lin, B. Guo and Y. Lu 7369
Reentry Trajectory Optimization of Airbreathing Hypersonic Vehicles Based on GaussPseudospectral MethodB. Yang and S. Sun 7375
Analysis of Dual Stator-Winding Induction Generator Based on AnsoftX.J. Shi, L.S. Liu and J. Wang 7381
Molecular Dynamics Simulation of the Rapid Solidification of Liquid ZincR.N. Ma, H.C. Qiu and J.J. Wu 7385
Modeling and Simulation for Super Capacitor Braking Energy Recovery Process of MicroEVJ.Y. Qu and L.Y. Liang 7390
Application of Complex Method for Optimization of Isolated Heat Pipe Heat ExchangeSystemR.H. Wang, P. Wang and Y.F. Zhu 7396
Normalized Energy Stability Margin Based Analysis of Omni-Directional Static Walking ofa Quadruped Robot on Rough TerrainL. Zhang and S. Gao 7401
Hot-State Numerical Simulation Study on Top-Blown Bath in ISA FurnaceS.B. Wang, H. Wang, J.X. Xu, D.F. Zhu, H. Sun and H.J. Li 7406
Finite Element Analysis of Fiber-Reinforced Iron-Boron AlloyY. Zhang, W. Yang and J.J. Wu 7413
Front Car Door Modal Analysis Based on Finite Element MethodL. Sun and Y.C. Liu 7418
bbb Manufacturing Science and Technology
Switched Reluctance Motor Drive System Model and Simulation Based on ANSYS andSIMULINKX.K. Yan and X.W. He 7422
Electromagnetic Force Modelling for Hybrid Magnetic BearingY. Cao, M. Zong and J. Zhang 7428
Fuzzy Control and Simulation Studies of Hot Rolling H-Beam’s Water Supply SystemX.G. Yu, H.C. Chu and J. Liu 7433
Simulation of Permanent Magnet Synchronous Motor for Electric Vehicle Indirect-TorqueControl SystemC.L. Wang, J.J. Li and X.Y. Feng 7438
Low-Speed Turning Back Simulation and Evaluation of a Car Based on ADAMSY.C. Liu and L. Sun 7444
Zero Internal Force Control for a Dual-Arm Space RobotH.C. Zhao and C.Q. Wang 7449
The Influence on High-Speed Electrical Multiple Unit by Fluctuation of Traction PowerSystem’s VoltageR.K. Liu, C.Y. Chen and Y.X. Lu 7455
Steering Wheel Angle Pulse Input Simulation and Evaluation of a Car Based on ADAMSY.C. Liu and L. Sun 7461
Design of Photovoltaic Generation Monitoring System Based on WinCCD.T. Wang and D.D. Yao 7465
A New Method of Fault Diagnosis with Soft Set TheoryX.L. Sun 7470
Design of Random Combination System Based on Five Common Kinds of MechanicalTransmissionR.M. Qin 7475
Modeling and Analysis of a Turbidostat Model with Monod-Type Kinetics and StateFeedback ControlY. Tian and L.S. Chen 7480
Circuit Model of Laser-Triggered Surface Flashover Switch in Vacuum Condition withPulsed VoltageR.Z. Pan, Y.H. Wang, Z.Z. Zhao, W. Xu, Q.L. Jin, P. Yan, J. Wang and G.S. Sun 7486
Detection of Electromagnetic Pulse Induced Hazard on Electroexplosive Device Based onOptical-Fiber FluorescenceL.S. Liu, W.S. Zhang and X.P. Zhu 7492
Risk Assessment Model of Automobile Defect Based on WeibullG.Z. Huang, Y. Wang, Y. Chen and J. Wang 7496
The Fuzzy Immune PID Control Based on the Water Position of the Steam GeneratorY. Xue and T. Wang 7503
Electromagnetic Compatibility Analysis of Carbon Fiber Cabin Struck by Lightning in theAircraftD.D. Guo, D.L. Su, X.Y. Zhao, L.P. Deng and Y.F. Chen 7509
The Switched Control of Single Phase Active Power FilterY.F. Zhang, X.G. Cheng, X.J. Zong, Q.Q. Miu, X.H. Chen, Y.L. Wang and G. Chen 7515
Analysis and Experiment of the Eddy Current Losses for Canned MotorY.J. An, G.M. Liu, H.L. Wen, W.Q. Zhao, L.P. Xue and C.Y. Guo 7521
The Pole Width Modulation Method and Experiment on Reducing the Voltage Harmonic ofPM Wind GeneratorY.J. An, W.Q. Zhao, H.L. Wen, G.M. Liu and H. Yuan 7526
A Path Planning Approach for Wedge/Aspheric Lens Element Grinding Based on SpaceCoordinate TransformationN.N. Zhang, C. Jiang, Z.Z. Wang and Y.B. Guo 7533
Study on the Safety Design and Test Method of Ultrasonic Cleaning Device for the MotorWindingH.P. Zhang, J.Z. Sun and M.T. Gu 7538
Pressure Analysis of Hydraulic Pumping System of Concrete PumpW.N. Qiu and H.Y. Wei 7543
Attitude Control of Rigid Body Using Sliding Mode ControlH.H. Bian and Z.H. Wang 7550
Advanced Materials Research Vols. 383-390 ccc
Vision-Based Guidance for an Unmanned Aerial Vehicle Following a Moving TargetT. Qin, W.C. Chen and X.L. Xing 7556
An Empirical Model for a Variable Speed Refrigeration SystemH. Li and J.Y. Fei 7563
The Variable Speed Direct Drive Permanent Magnet Synchronous Wind Power SystemUsed on Matrix ConverterB. Yang, G. Zeng and Y.R. Zhong 7569
An Improved Geomagnetic Matching Algorithm Using Rotation Angle Search TechniqueY.J. Liu, Y. Zhao and F.L. Wu 7576
A Signal Quality Monitoring Based on Least-Squares for Global Navigation Satellite SystemH.L. Chen, Y.B. Zhu and R. Xue 7582
An Improved Adaptive Kernel-Based Object TrackingZ.H. Liu and L. Han 7588
Analysis and Discussion of the Influence Factors of the Wind PowerG.J. Li and Y.J. Hu 7595
Robust Tracking Control Based QFT and Pade Approximation for Flight SimulatorZ.H. Liu, D.K. Shen and S.Z. Liu 7600
Counting of Microscopic Cells Based on Grads Hough TransformJ.J. Chen, Y.J. Gao and Z.J. Deng 7607
Composition Analysis of Ge Graded Si1-xGex Alloy Films by Capacitance-Voltage MethodY. Yang, F. Yu, P. Han, R.P. Ge and L. Yu 7613
Composition Analysis of Ge/Si1-xGex: C Buffer on Silicon Measured by Planar ScanningEnergy Dispersive SpectroscopyZ.Z. Lu, F. Yu, L. Yu, L.H. Cheng and P. Han 7619
Research on a Novel Power Inverter Control Strategy Based on Micro-GridW.M. Chen, W. Wang, H. Cai and G.C. Chen 7624
Research on Tension Control System of Filament Winding MachineJ. Yan and Q.J. Zhu 7631
The Dynamic Characteristics of AD590L.D. Fang, J.K. Zhang, X.T. Li and X.M. Xiang 7637
Study on System Identification Method Based on PID Control AlgorithmY.D. Tang, X.C. Zhu, L. Feng and C. Gui 7644
Based on the Nc Machining System Error Aspheric Analysis and ResearchH.Y. Wang and X.M. Hu 7649
A Computed Model of the Pendulum Test of the Leg for Quantitative Evaluation of MuscleSpasticityX. Zhang and T. Fang 7654
Application of Fuzzy Assessment Theory in Tower Crane SafetyL. Bin, L. Lei and L. Wei 7657
Expected Model for Time-Energy Trade-Off Problem of Product DisassemblyG.D. Tian, R.J. Liu, Y.M. Liu, J.W. Chu, G. Xu and B. Chen 7663
The Characteristics of Calcium-Based Sorbent Burning Pore Structure and Simulation ofGas-Solid Mass Transfer in VulcanizationB.Q. Xiao 7669
Synthesis and Photovoltaic Properties of Fluorene-Based Copolymers with ThiopheneHeterocycle on the Side ChainQ. Hou, X.H. Zeng, X. Xu, T. Guo, H.Y. Zhen and G.L. Li 7677
Stress Problems at the Steam Drum Fatigue Checking Point of a Supercharged BoilerX.W. Zheng, Z. Li, X.H. Chen, Y. Sun, H. Wang and X.Y. Wen 7682
Numerical Simulation and Engineering Application of Bolt’s Supporting in Tectonic StressFieldF. Nan, Z.Q. Kang and F.P. Li 7691
Research on Numerical Analysis of Landslide Cataclysm Mechanism Coal MineZ.Q. Kang, Y.C. Wang, F. Nan, S.L. Yuan and J.L. Yang 7697
Active Disturbance Rejection Decoupling Control for Aero-EnginesH.B. Zhang, R.X. Wang, Y.H. Lin and Y.J. Li 7702
ddd Manufacturing Science and Technology
Optimization and Application of Composite Index Method for Evaluation of Rock BurstRatingJ.Y. Zhang, X.R. Luo, L.W. Guo and X.M. Gong 7708
Filed Test Studies on Internal Force of Pile in Pile-Anchor Supporting System for DeepFoundation PitC.F. Wu and C.H. Li 7713
Analysis of Condensing Temperature Set Point of Air-Cooled Refrigeration System with anElectronic Expansion ValveZ.G. Zhou and H. Zhang 7718
The Toxic Effects of Algicidal Bacteria L7’s Algicidal Components to Brachydanio rerioC.M. Zhang, Y.L. Zhang and W.B. Pan 7723
Numerical Simulation of the Spray Characteristics in Small Scale Liquid Rocket EngineCombustion ChamberN. Zhao, Y.G. Yu and Y.Q. Wang 7729
Experimental Study of Integrated Vortex Board with Exergy AnalysesF.Y. Song, Y. Ma, P. Zhang and Y.J. Chen 7734
Development and Realization of Bag Filter On-Line Monitoring System Based on ACCharge InductionZ.M. Xue 7740
Application of Artificial Neural Network for Modeling of Mechanical Cooling TowerW.S. Huang, C.W. Chen, C.W. Lee, C.L. Chen, T.S. Jan, Y.C. Chang and T.W. Chang 7746