T30 Trainer Airplane Instruction Manual

工具 Tools Needed

F1F2

F3

爪牙螺母Claw nut

F7-3F7-2F7-1

F21F4

F5 F6

F13

F8

F9F14

F14-1

F15F15-1

F21

F11

F12

F10 F16

F12-1

F22

F17

F27F28

F29

F18 F19 F20

F38

P4

F40

F23

F30

F25

F26F24

F23-1

P5

F32

F33 F34

F35

F36

P3F32-1

F37 F37-1

F31

F14F14-1F14-2

背面装爪牙螺母

打磨成机身一体弧度

螺丝固定

碳杆carbon rod

磁铁magnet

磁铁magnet

R4

E8

E3

E4E1

E7E6E5E2

E9

E10

R11

R10R9

R5

R7

R6R1x2

R2

R3R8

R12

P2

P1

W1W14 W14-1

W2

W3 W4W6

W16W16-1

W5

W7 W8W18

W18-1

W9W10

W11

W21 W22

W4-1

W23

W16

W17 W17-1

W19

W20W13x2

W38x3

W20-1x3

W16-1

W24 W25W26 W28W27 W29

2,尾翼组装 Assemble the Tail Wing

机翼和尾翼请在平整的工作台上进行拼装，拼装时保持机翼平直。

3,机翼组装 Assemble the Wing

W5

1,机身组装 Assemble the Fuselage

Claw nut爪牙螺母

Claw nut爪牙螺母

Claw nut爪牙螺母

F30 F40粘贴时用水湿润后再进行蒙板粘贴Soak the F30 and F40,and paste the cover board.

Firm with screws螺丝固定Firm with screws

install the claw nut at the back.

Polish it with same radian as fuselage

Assemble the wing and tail on the smooth desk,make sure the wing is straight.

轻木条P6 P6-1交错拼接Install the balsawood stripsP6 and P6-1 in cross.

参数翼展：1400mm机长：1070mm起飞重量：≈2000-2500g

推荐配置马达：2814-3520 600-1000KV电调：40A电池：4S 3600-5000mAh舵机：17g*4

引擎：2C36 / 4C56

桨叶：10-12inch通道：≥4CH

Speci�ication Wingspan: 1400mmLength: 1070mm Flying Weight≈2000-2500g

Suggested Equipment Electric powered: 2814-3520 600-1000kvESC: 40ABattery: 4S 3600-5000mAhServos: 17g*4Gas engine class: 2C36 / 4C56Propeller: 10-12inchRadio≥4CH

W32

W30W30-1

W36

W15x2

W32-1

W12

W35-1 W35

W37

W21x3

（按机翼弧度打磨成弧形）

W33

W33-1W34

W31-1

W31

D3x2

D2 D2D4

D1

D6

D5

螺丝screw

插入Insert

4,马达座组装 Install the Motor Mount

5,起落架安装图示 Assemble the Landing Gear

7,舵机，舵角安装图示 Install the servo and servo horn

8,重心调试位置图示 Adjust the C.G.

6,机翼及尾翼安装到机身图示 Assemble the wing onto the fuselage

升降舵舵机副翼舵机

X1*2X2X3

垫入X1-3并打磨

C.G

≈80mm

(Polish as per the radian of the wing)

(Paste the W12 only with W35)（W12只与W35粘贴）

机翼组装完成后切下副翼，按图示粘贴W37并打磨，再用纸合页把副翼连接到机翼。

Cut off the aileron once the wing is built up,paste the W37 as picture shown,then polish ;and connect the aileron with the wing by the paper hinges.

Assemble the other wing same as the above steps,connect the two wings together with the carbon tube,and firm with glue.

另一边机翼参考以上步骤拼装，两边机翼组装完成后通过碳管对插在一起，连接处用胶水粘合。

D4可根据选用的马达长度进行增加或减少。The length of D4 could be increased or lessened as per the motor length.

Firm the motor mount onto the head with screws.

马达座用螺丝固定到机头

Elevator servo转向舵舵机

Connect the rudder servo with the front steering wheel.

When it's powered by gasoline,this servo controls the throttle.

连接前转向轮

使用油动马达时，此舵机控制油门

Aileron servo