1

Parts Quantity

2

Q

TFront legRear leg

Leg crossbar

Right back crossbar Left back crossbar

Right arm Left arm

seat support Seat assembly

Canopy edge bar Canopy side bar

Seat cushion Canopy

Arm cushion

long barshort bar

4

AA M6 x 36L bolt 1

BB M6 x 65L bolt 4

CC M8 x 30L bolt 8+1

DD M8 x 65L bolt 4

EE M8 x 75L bolt 2

FF M6 nut 3

GG M8 nut 6

HH M6 metal washer 3

II M8 metal washer 18+2 spare

JJ plastic washer 2

KK steel plate 2

LL 2

MM black knob 2

NN M6 bolt cap 5

OO M8 bolt cap 14+1 spare

PP M6 nut cap 3

QQ M8 nut cap 6

3

spare

double S-hook

1) Align the two Top Frame Bars (A). Place one of the Steel Plates (KK) on top of the joint of the Frame Bars (A). Align the two holes in the Top Frame Bars with the two holes in the steel plate. Insert two M6 x 65L Bolts (BB) through the upper steel plate and through the Top Frame Bars. Align the two holes of the lower steel plate with the bottom of the Top Frame Bar (A) and continue the bolt through this plate and an M6 Nut (FF). Don’t tighten completely. See Fig. 1.

2) Align the two holes at one end of Top Frame Bar with the two holes in the top of the Front Leg (B) and the two holes in the top of the Rear Leg (C) on the other side. Insert an M8 x 65L Bolt (DD) through an M8 Metal Washer (II), through Front Leg (B), Top Frame (A), Back Leg (C), through another Washer (II) and into an M8 Nut (GG) for each hole. Don’t completely tighten. See Fig. 2. Repeat procedure on the other side of the frame.

3) Adjust the angle of the two legs. Place a Leg Crossbar (D) between two legs on one end of the frame, lining up the bolt holes. For each hole in the front and back legs, insert an M8 x 30L Bolt (CC) through an M8 washer (II), through the leg and into the leg crossbar. Don’t completely tighten. See Fig. 3. Repeat procedure for the crossbar between the other legs.

M6 x 65L bolt

M8 x 30L bolt

M8 x 65L bolt

M6 nut

M8 nut

M8 metal washer

Steel plate

M6 bolt cap

M8 bolt cap

M6 nut cap

M8 nut cap

BB

CC

DD

FF

GG

II

KK

NN

OO

PP

QQ

2

8

4

2

4

16

2

2

12

2

4

Fig. 1

Fig. 2

Fig. 3

Frame Assembly

4

open nut

damaging

2

2

2

2

4) Join the Right and Left Back Crossbars (F, E) in the center and insert an M6 x 36L Bolt (AA) through the two Back Crossbars (F, E), through an M6 Washer (HH) and an M6 nut (FF). Do not completely tighten. See Fig. 4. Align the assembled back crossbar with the hole in the lower back legs. For each hole insert an M6 x 65L Bolt (BB) through an M6 washer (HH), through the Back Leg and into the Back Crossbar. Do not tighten completely. See Fig. 5.

5) Now go back and securely tighten all nuts and bolts. Place Bolt Caps (NN, OO) over all Bolts, and place Nut Caps (PP, QQ) over all Nuts.

6) Lay out the Right Seat Arm (G), Left Seat Arm (H), Seat Supports (I). Make sure that the labels marked “Front’’ on the arms are all facing the front edge of the seat. Connect the arms to the seat supports by sliding the tabs on the ends of the seat supports down into the brackets on the arms. Make sure they are securely seated. See Fig. 6.

7) Open the Seat Assembly (J) and lay it on top of the frame from Step 6, lining up the holes in the Seat Arms (G, H) with the holes in the side tubes of the Seat Assembly (J). Insert an M8 x 75L Bolt (EE) from outside through the arm holes, through a Plastic Washer (JJ), through the side bar on the Seat Assembly, through an M8 Washer (II) and an M8 Nut (GG). Don’t tighten completely. See Fig. 7. Repeat procedure on the other side. Then securely tighten the Bolts and Nuts and cover with Caps (OO,QQ).

Fig. 7

Fig. 6

Fig. 4

Fig. 5

Seat Assembly

5

M8 x75L bolt

M8 nutM8 metal washer

Plastic washer

M8 bolt cap

M8 nut cap

EE

GGII

JJ

OO

QQ 2

2

M6 nut

M6 metal washerM6 bolt cap

M6 nut cap

M6 x 65L boltM6 x 36L boltAA

BB

FF

HH

NN

PP

1

2

1

3

3

1

Fig. 10

Fig. 9

Fig. 8

8)

9)

6

(Q)

Position two Long Bars (L) so that the end marked "TOP" is upside. Hang the Double S-Hook (LL) through the top holes of long bars. Slide two pins on the outside of an arm through the bottom holes of two long bars . See Fig. 9. Position a Short Bar (K) so that the end marked "TOP" is upside. Hang the double S-Hook (LL) through the top hole of short bar. Drag out of the bracket of the short bar, and slide a pin outside of the Seat Assembly (J) through the Short Bar (K). Repeat the procedure for the other side. See Fig. 10. Then hang the whole assembley seat on the top frames. See Fig. 11.

See Fig. 8.

Fig. 11

MM Black knob 2

Fig. 14

Fig. 13

Fig. 12

12

13

14.

10)

11)

12)

M

P

N

7

(M)

.

Converting the swing to a hanging bed

Fig. 16

Fig. 15

13)

ONE-YEAR LIMITED WARRANTY

8

To convert the swing into a hanging bed, lift the brackets of the Short Bars (K), pull the pins out from the short bars. Fasten the back support of the seat assembly to the U-shape bracket of the Back Crossbars (E, F). When used as a bed, the seat assembly should be secured by these holders and not allowed to swing. See Fig .15 and 16.