svr1100 series user manual

DIGITAL VIDEO RECORDER

This manual will be changed timely without any notice. If customer has any doubt with it, please contact with our Technique.

1


USER MANUAL

Model: SVR1104/E

SVR1109/E SVR1104/EVGA

SVR1109/EVGA

Thank you for using our products, please read this user manual carefully before using this system!



2

Version Declaration

This manual will be changed timely without notice. The new content will be added to revised manual. We reserve the copyright for this user manual.

Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to local electrical safety codes. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation. 2．Transportation security Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation. 3．Installation Keep upwards. Handle with care. Do not apply power to the DVR before completing installation. Do not place objects on the DVR 4．Qualified engineers needed All the examination and repair work should be done by the qualified service engineers. We are nor liable for any problems caused by unauthorized modifications or attempted repair. 5．Environment The DVR should be installed in a cool, dry place away from direct sunlight, inflammable, explosive substances and etc. The power supply is DC 12V 3A, please use power supply from the whole package you purchased. Don’t insert metal into the DVR, this action maybe will cause an electric shock Don’t poll liquid into the DVR, this action maybe will cause short circuit inside the DVR. Keep the products clean and dry. Never hot plug any hardware; this action maybe will damage the ports of them.. Please use the standard lithium battery. If the system clock can not work, please replace the standard 3 V lithium batteries on the motherboard.



3

TABLE OF CONTENTS Chapter 1 Summary

1 Products features ...........................................................................................................................................4

Chapter 2 Appearance and Installation

2.1 Appearance ........................................................................................................................... 42.2 Sketch of the installtion ............................................................................................................ 5 2.3 Hard disk installation ............................................................................................................... 6 2.4 Connect Audio&Video ........................................................................................................... 72.5 Boot/Format Hard disk .......................................................................................................... 7

Chapter 3 Menu Operation

3.1 Menu...................................................................................................................................... 7 3.2 Channel Setup ......................................................................................................................... 8 3.3 Record Setup ........................................................................................................................... 8 3.4 Record frame rate ................................................................................................................. 83.5 Record quality ....................................................................................................................... 8 3.6 Schedule ............................................................................................................................... 83.7 Sensor Setup......................................................................................................................... 93.8 Hard disk Setup................................................................................................................... 10 3.9 Miscellaneous Setup ........................................................................................................... 103.10 Network Setup..................................................................................................................... 113.11 Video Backup ...................................................................................................................... 11 3.12 Reset menu ......................................................................................................................... 11

Chapter 4 Playback

4.1 Playback.............................................................................................................................. 12 Chapter 5 Player software

5.1 Player Software ................................................................................................................... 12 Chapter 6 IE Brower

6.1 Setup and install.................................................................................................................. 136.2 IE Browser........................................................................................................................... 14

Chapter 7 System Mode 7.1 System Mode ...................................................................................................................... 15

Chapter 8 Specification&accessories

8.1 Specification ........................................................................................................................ 16 8.2 Accessories ......................................................................................................................... 17


Chapter 1 Summary

1.1 Products Features

4 channel DVR:4 video input-1 video output;2 audio input-1 audio output 9 channel DVR: 9 video input-1 video output;2 audio input-1 audio output Support PAL/NTSC Linux Operation system Multi recorder mode: consecutive record, motion detection record, sensor record Event log and time search to playback Video shield Support VGA video output (Item Number with “/VGA” is without VGA output) RS-485 port inside ,support PTZ control Password protection IR control Support large capacity hard disk(more than 500G) Support USB mouse operation Support USB backup

Chapter 2 Appearance and Installation

2.1 Appearance

Front panel of 4ch/9ch DVR

1. IR control window 2.Work light 3. Recorder light 4.Power light

4 channel back panel

1. Network /USB Port 2. Audio input 2 3. Audio Output 4. Audio input 1 5-8: Video input 9. Video Output 10. VGA output(Optional) 11. Power switch 12.Fan 13. RS485 Port 14: Power Interface

9 channel back panel


4


1. Network /USB Port 2. Audio input 2 3. Audio Output 4. Audio input 1 5 Video Output 6-14 Video Input 15. VGA output(Optional) 16. Power switch 17.Fan 18. RS485 Port 19: Power Interface

Remote Control(Reference only ,please subject to material subject)

0-9 Number/ Channel choose

ALL Preview all screen

MENU Enter/Exit Menu

▲ Up

▼ Down

► Right

◄ Left

OK/PTZ Confirm

Fast Return

Fast forward

Pause

Play

Mute

Audio output

Stop

Recorder key


5


2.2 Sketch of Installation

Sketch of Installation

Alarm device installation

2.3 Hard disk installation(the picture is just for reference, DVR doesn’t include HDD)


6


Open the upper case of system and install hard disk on the four position holes. Connect the power line and the date line to the motherboard.(Support the SATA and IDE Hard

disk, two HDD can work together) Tighten the screws after fixing the upper case, press the switch button to run the system.

Remark: Please use the incidental power supply ; if use other power supply ,maybe it will cause some problems

2.4 Connect Audio and Video Input/Output

Connect video signal from the BNC interface to the video interface of the back panel, use the video line to connect the video output to VGA interface.

Connect the audio signal from AV interface to the audio interface of the back panel, use audio line to connect the audio output to the speaker.

2.5 Boot /Format Hard Disk

Enter the start menu after starting run this system

Check the hard disk automatically, and the system will pops-up a window to remind user if to format the HDD or not, press [OK/PTZ] to confirm format the hard disk.

After formatting the Hard disk, user can enter into the preview menu.

Chapter 3 Menu Operation

3.1 Menu

Press[MENU] to enter menu content This manual will be changed timely without any notice. If customer has any doubt with it, please contact with our Technique.

7


(▲/▼) to choose setup items (OK/PTZ) button to confirm [MENU] button to exit


8

3.2 Channel setup

(▲/▼/ / ) to choose channel [OK] to confirm open or close If close the channel ,it will show “ NO VIDEO”

3.3 Recorder setup

(▲/▼/ / ))to choose channel [OK] to confirm open or close It will stop recording if select”close”, and can not setup the record

frame rate.

3.4 Record frame rate setup

(▲/▼/ / ) to choose channel to add frame rate [STOP] to reduce the recorder frame rate Total frames: PAL:50 fps; NTSC: 60 fps (Choose the frames for each

channel flexibly)


3.5 Record quality

Press [OK] to choose video quality grade for recording: High 、middle、low.

The higher of the video quality grade, the better of video quality, the bigger of the size of recorded file

3.6 Schedule

Setup the record mode from every hour to 24 hours (▲、▼、▼、 / ) to choose time ,[ok] to choose the record mode,

repeat [OK] to switch the record mode;

( ) no record,( ) record: normal record ( )Sensor record：motion detection record and alarm record

Remark: After setting the schedule, press ( REC) , the setup will take effect, otherwise it will not start to record.

3.7 Sensor Setup

Sensor record time: set record time if the alarm triggered. Alarm on time: choose the alarm time if the alarm triggered. There are three options: when it is ON, the system will not stop

recording nor alarming. When it is OFF, the system will not record nor alarm. When it is any time of (5,10,15,20,25,30s), it will record or alarm according to the set time

H/W Sensor Setup: choose channel for alarm mode Select “on” to enable the alarm, select” not installed “ to disable

to alarm

Remark: All settings are according to the sensor that you are using.


9


Motion detection setup

Open/Close:[OK] to open or clos ress ▲、

▼ to choose channel, （e the motion detection , p


10

）and [OK] to setup area of the motion

ction. 1 is the lowest sensitivity,3 is the highest

3.8 Hard drive setup

Overwrite Enabled: the recorded file will be deleted if the hard driver is full after selecting “Yes” ; the system will stop recording

s

sk

Remark: Connect 2pcs hard disks, support SATA and IDE at the same time . HDD can be more than 320 G

detection. Sensitivity of motion detection: 0,1,2,3. Select 0 to cancel the motion detesensitivity. [STOP] to choose the sensitivity

and the recorded file will not be deleted even if the hard driver ifull after selecting “No” Display the information and capacity of the hard disk and use information

Hard disk format: format the hard disk and all data on hard diwill be deleted.

The default password to format the hard disk is: 111111


3.9 Miscellaneous setup

Change Password: change the system password, the default password is : 111111


11

NOTE: If user forgets the password, just take off the button battery on the motherboard and re-install it 10 minutes later. Re-start the system, it will recover to the default password.

Set time: (▲、▼、 / ) to choose time ,[OK] to change number.

Hidden channel: If one channel is hidden, user can not get video on the preview menu but could record normally,[OK] to choose the channel that you want to hidden.

Audio port setup: select the audio channel, choose (on/off) to record with audio or not.

NOTE: The system has 2 audio input, 1 audio output. If user want to listen the audio from another channel, press [AUDIO]button on the control to switch the channel to listen-in, press [MUTE] to on/off the audio .

PTZ Setup

Speed: 2400,4800,9600,19200,38400(for option),press（OK）to choose

Protocol: PELCO-D,PELCO-P for option;press（OK）to choose.

Channel: choose the channel with PTZ camera,[OK] to choose.

Address：（ / ）to choose address

NOTE: PELCO-D to choose 1, PELCO-P to choose address 2

● Language setup:[OK] to choose language, support Chinese and English

3.10 Network setup

MAC: the physical address , (▲、▼)to choose number,[OK] to confirm.


NOTE: MAC address should be start from”00”; the rest number can not be all “00”nor“FF”. There will not exist the same MAC address in the same network .

IP address：setup IP address k

otocol port ,the default is 80 access network, one is “ADMIN” who have all rights to operation;

[OK] to setup the start time and end time , (▲、▼、OK) to setup time

NOT ser should use the player we provided to play it

Enter the correct password, the system setup will renew to the default status. About password setup, please reference

Chapter 4 Playback

IP allocation: DHCP or STATIC.

Subnet mask：setup subnet mas Gateway：setup gateway DNS address：setup DNS address HTTP port：Setup WEB pr User setup: two authorized users can

another is “normal user” who only could preview. DDNS settings: DNS ISP and register domain name .Setup DDNS according the register information.

3.11 Video backup

The system will calculate the size of the file after setup time , [OK] to choose device to backup.

Two methods for backup: one is backup to CD/DVD, another is backup to USB device

E: Backup file is .MCG format, u

3.12 Reset Menu

to 3.9.

Click [play] button to enter playback mode, system will play the latest recorded file automatically.

he recorded file lists, the ed file is on the top.

4.1 Playback

Two playback modes: events list, time list. Press [MENU] during playback to enter tdefault status is events list, the latest record(▲、▼) to choose the files that user want to play, press[PLAY] to start.

12This manual will be changed timely without aechnique.

ny notice. If customer has any doubt with it, please contact with our T


Press[MENU] to back to the playback mode from the playback lists. （▲、▼） to choose event lists or time lists.

(▲、▼、OK) to setup time for playback, press[PLAY] to start. If there is no recorded file, it will show “NO VIDEO” on the

Chapter 5 Player software

screen.

The backup files are MCG format. User has to use the player in the software CD to play it. ind ICON as below, click it to run it: From the software CD, user will f

Operation menu is as below：

:


13

open the backup file

: Fast backward

：Return; ：Pause

：Play; ：Fast forward

：Capture

：voice close /open，volume

Chapter 6 IE Browser

.1 Setup and install IE

g through IE, user has to set the internet option as below:

ws, Select“tools”----“internet properties”

6

NOTE: Before remote viewin

1. Open one Internet windo


2. Select “security”—“Custom level”, enable all the ActiveX and plug- in

3.Confirm it and click “yes”

4. Go back to the internet explore windows, type the IP address of DVR to remote view

6.2 IE Browser

1. Type the IP address of DVR, User will get remind of downloading an ActiveX, please press “confirm”, and

2. After install ActiveX and will pop up the windows as follow. If this window doesn’t pop up, please close this

download it. if the ActiveX could not download ,please click “if the Active could not download, click here” “download” ,after downloading , please double click to install.

IE page and open another one, type the IP address correctly.


14


3.Click and will pop up the login windows, enter the user name and password, the default user name and password both are : ADMIN

Remark: user name and password are both capital words

Click and the preview menu will 2X zoom

IE interface


Connected：Indicate system connect status and trasfer speed 15


Capture tools：Captuer and record control Remote DVR Control Panel ：DVR Control

：Record/Playback the file from DVR

：Input camera

：Indicate the camera which is recording

：Record setting of DVR ：Frame Rate Status of DVR

：Schedule setting for DVR

：Sensor settings ：Hard disk status

:Alarm recorder time : PTZ control

Chapter 7 System Mode The DVR supports PAL and NTSC format. Before delivering, it should be set with correct system according to different market. Once user receives DVR with improper system, user can adjust the correct system through the jump line on the motherboard JS1.

PAL System (Using plastic cover to connect the JS1 pin with the pin at the side of PAL）


16


NTSC System（Using plastic cover to connect the JS1 pin with the pin at the side of NT）:

NOTE: To avoid open the DVR case again, it will be better to setup the system while installing the hard disk

Chapter 8 . Specification and Accessories

8.1 Specification

Item SVR1104 SVR1109

Video I/O 4 ch input /1ch output 9ch input/1ch output

Audio I/O 2 ch input /1ch output 2ch input/1choutput

Display resolution PAL：720X576@25fps/ch

NTSC：720X480@30fps/ch

PAL：720X576@25fps/ch

NTSC：720X480@30fps/ch


17



18

Recorder resolution PAL：720X288@50fps(Total); NTSC：720X240@60fps(Total)

PAL：720X288@50fps(Total); NTSC：720X240@60fps(Total)

Motion detection Setup area and sensitivity Setup area and sensitivity

Hard disk interface Support IDE or SATA

IE browser Support

PTZ Control Support RS- 485 interface control

USB interface Support USB2.0

VGA interface Support(for Optional)

Network interface RJ45

IR remote control Support

8.2 Accessories

1、Power supply line 6、Hard disk data line

2、Power supply 7、Hard disk power supply

3、User manual(Optional) 8、M3*6 screw

4、 CD 9、Certification（Optional）

5、 Remote control 10、Warranty card（Optional）

svr1100 series user manual

Documents