stop - tempur-pedic · 2020. 9. 10. · stop please read instructions before setup of new...
TRANSCRIPT
STOP PLEASE READ INSTRUCTIONS
BEFORE SETUP OF NEW TEMPUR-PEDIC® SMARTBASE!
PLEASE READ INSTRUCTIONS
BEFORE SETUP OF NEW TEMPUR-PEDIC® SMARTBASE!
PLEASE READ INSTRUCTIONS
BEFORE SETUP OF NEW TEMPUR-PEDIC® SMARTBASE!
STOPPLEASE READ INSTRUCTIONS
BEFORE SETUP OF NEW TEMPUR-PEDIC® SMARTBASE!
PLEASE READ INSTRUCTIONS
BEFORE SETUP OF NEW TEMPUR-PEDIC® SMARTBASE!
PLEASE READ INSTRUCTIONS
BEFORE SETUP OF NEW TEMPUR-PEDIC® SMARTBASE!
STEP 1 - BASE SETUP
Setup is now complete!
Only 1 processor (Base B) is used for tandem/split setup.
For help installing the Tempur-Pedic® Sleeptracker® app, information can also be found at : https://www.sleeptracker.com/getapp/tempur
U.S.: 1-844-309-3598
Canada: 1-800-887-4321
Mexico: 01-722-273-1810
a. Remove bases from packaging. Position bases to align HEAD/FOOT ends the same direction. Note A/B position for the following steps.*
b. Locate printed materials (Base B only)*
c. Install legs
d. Connect power to base(s)
e. Insert remote batteries
f. Place units on their side with bottom towards each other for ease of connections in step 2.*
STEP 2 SYNC CORD INSTALL (BASE A&B)
STEP 4 SLEEPTRACKER® PROCESSOR SETUP (BASE A ONLY)
STEP 5 SLEEPTRACKER® PROCESSOR SETUP (BASE B ONLY)
STEP 6 SLEEPTRACKER® APP SETUP (BASE B ONLY)
a. Disconnect male Battery Backup Box Cable from female Sleeptracker® Smart Cable.
a. Disconnect Sleeptracker® Sensor Cable from Base A Sleeptracker® Processor.
a. Connect Base A Sleeptracker® Sensor Cable to Base B Sleeptracker® Processor.
a. Test all functions on remote.
b. Connect male Sync Cord to female Sleeptracker® Smart Cable.
b. Route Sleeptracker® Sensor cable through rubber conduit and under Base A and B frames.
b. Route Base A Sleeptracker® Sensor Cable through rubber conduit.
b. For Customer APP setup, provide APP Setup Card from printed materials (Base B card only*).
c. Connect male Battery Backup Box cable to female Sync Cord. Discard additional sync cord, only 1 is required.
d. Position bases back on their legs to complete the remaining steps. Assemble mattress retainer bars and connecting straps.
c. Disconnect Base A Sleeptracker® Processor from USB Extension Cable.
c. Call Tempur-Pedic Customer Service for delivery confirmation.
ERGO EXTENDTM
+ SLEEPTRACKER® SYSTEM
SLEEPTRACKER® ERGOTM AND ERGO EXTENDTM TWIN LONG/SPLIT CA KING 2 UNIT SETUP
REFER TO IMAGES BELOW FOR STEPS 2-6 FOR SLEEPTRACKER® SETUP
Control boxUSB Extension CableUSB Ports Underbed Light
USB Ports
MassageMotor
Sleeptracker® Sensor
HEAD END
*Split Unit setup reference. Base A is on right side.
Sleeptracker® Smart Cable Underbed
LightBattery
Backup BoxHead Motor
APP Setup Card
Sync Cord Connecting Strap
Foot Motor Massage
Motor
FOOT END
Sleeptracker® Processor
ERGOTM
+ SLEEPTRACKER® SYSTEM
Underbed Light
STEP 3 SLEEPTRACKER® SENSOR INSTAL (BASE A&B)
a. Remove Sleeptracker® Sensor from twist ties.
b. Insert Sleeptracker® Sensor into pocket.
c. Secure pocket to velcro strip under head deck.