steriboreä bpe high purity astm a270 316l · 2014-08-01 · steribore bpe high purity astm a270...

- 10 -

STERIBORE BPE HIGH PURITY ASTM A270 316L STAINLESS STEEL TUBES

STERIBORE is ideal for Bioprocessing and Pharmaceutical applications requiring mechanically polished surface finishes to 20 Ra µin (0.5 Ra µm) ID maximum and 32 Ra µin (0.8Ra µm) OD maximum. STERIBORE Tubes exceed the requirements of the ASME BPE specification on dimensions and tolerances and fully meet the BPE specification for OD and ID surface finishes STERIBORE Tubes are marked with specification, size, grade and heat number and BPE surface finish designation. Tubes are supplied in 20ft / 6M lengths with ends prepared for orbital welding and capped. STERIBORE tubing is available from stock with ID cleaned for oxygen service.

STERIBORE : Other ID cleaning procedures are available including thermocouple cleaning per ASTM A632 or Nitric Acid & DI Water Rinse. The DI water systems used guarantees 50 PPB with an average of 10 PPB and a restivity of 17.98 to 18.03. Ultra High Purity 99.9999% pure Nitrogen is also utilized which is filtered to 0.003 micron at the point of use. Cleaning and packaging is performed in a Class 100 clean room.

NOMINALO.D. TUBE

SIZES

NOMINALWALL

THICKNESS

COMPARISON OF STERIBORE DIMENSIONAL TOLERANCES WITH BPE SPECIFICATIONSO.D. SPECIFICATION WALL THICKNESS SPECIFICATION LENGTH

BPE ACTUALSPEC.

STERIBORETYPICAL

SPEC.

BPE ACTUAL SPEC

STERIBORETYPICAL SPEC.

STERIBORELENGTH

in Mm in mm in mm in mm In mm In mm In mm½” 12.7 0.065 1.65 ± 0.005 ± 0.13 ± 0.00

5± 0.13 +0.005/-0.008 +0.13/-0.20 ± 0.002 ± 0.05 +0.12/-0 +3.18/-0

¾” 19.05 0.065 1.65 ± 0.005 ± 0.13 ± 0.005

± 0.13 +0.005/-0.008 +0.13/-0.20 ± 0.002 ± 0.05 +0.12/-0 +3.18/-0

1” 25.4 0.065 1.65 ± 0.005 ± 0.13 ± 0.005

± 0.13 +0.005/-0.008 +0.13/-0.20 ± 0.002 ± 0.05 +0.12/-0 +3.18/-0

1.5” 38.1 0.065 1.65 ± 0.008 ± 0.20 ± 0.005

± 0.13 +0.005/-0.008 +0.13/-0.20 ± 0.002 ± 0.05 +0.12/-0 +3.18/-0

2” 50.8 0.065 1.65 ± 0.008 ± 0.20 ± 0.005

± 0.13 +0.005/-0.008 +0.13/-0.20 ± 0.002 ± 0.05 +0.12/-0 +3.18/-0

2.5” 63.5 0.065 1.65 ± 0.010 ± 0.25 ± 0.005

± 0.13 +0.005/-0.008 +0.13/-0.20 ± 0.002 ± 0.05 +0.12/-0 +3.18/-0

3” 76.2 0.065 1.65 ± 0.010 ± 0.25 ± 0.005

± 0.13 +0.005/-0.008 +0.13/-0.20 ± 0.002 ± 0.05 +0.12/-0 +3.18/-0

4” 101.6 0.083 2.11 ± 0.015 ± 0.38 ± 0.005

± 0.13 +0.008/-0.010 +0.20/-0.25 ± 0.0025 ± 0.06 +0.12/-0 +3.18/-0

Mechanical Tests: Full mechanical testing is conducted according to ASME SA249 and ASTM A270/ A249/ A450. This includes reverse bends, flattening and flange testing, eddy current (non-destructive) electric testing. All material is 100% bore-scoped inspected prior to mechanical polishing. Hydrostatic and other tests available on request.

CHEMICAL COMPOSITION – 316LELEMENTS BPE SPEC. STERIBORE TYPICAL

OTHER ALLOYS AVAILABLE ON REQUEST

(C) CARBON, max 0.035% 0.020%(Cr) CHROMIUM 16.0-18.0% 16.40%(Mn) MANGANESE, max 2.0% 1.70%(Mo) MOLYBDENUM 2.0-3.0% 2.10%(Ni) NICKEL 10.0-15.0% 10.20%(P) PHOSPHORUS, max 0.040% 0.029%(Si) SILICON, max 0.75% 0.50%(S) SULFUR, max 0.005-0.017% 0.013%

STERILEX 10 is STERIBORE tube electropolished to 10 Ra µin (0.2 µm) ID. The ID of the tube is bright reflective and chromium enriched and receives 100% inspection. Cleaning is

Global Stainless Ltd., Tel: + 353 21 4968578 Fax: + 353 21 4312921 e-mail: [email protected]

- 11 -accomplished with High Purity Low TOC Deionized water and Electronic grade High Purity Nitrogen.

STERIBORE and STERILEX 10 tubes are packaged using protective 6mm poly-sleeving along with air-tight end caps. Tubing is placed in wooden boxes for maximum protection during shipment. Other packaging is available on request.

TECHNICAL DATA

ASME BPE BIOPROCESSING EQUIPMENTACCEPTANCE CRITERIA FOR INTERIOR SURFACE FINISHES OF TUBING

ANOMALY OR INDICATION ACCEPTANCE CRITERIADemarcation If area is less than the tube dia. and Ra increases <50%.Grit Lines If Ra is met.Longitudinal welds If polished smooth, blended, and Ra is met.Nicks If dia. <0.25”, any depth

If dia. >0.25” and depth <0.003”.Oxides If not visiblePits (per tube length) Up to 6, if dia. <0.020” and bottom is shiny (Note 1).Scatches (Note 2) If depth <0.003”.Star burst If < 75% of the width of the weld bead.Surface cracks None acceptedSurface inclusions If Ra is met.Surface residuals None acceptedSurface roughness (Ra) See Table SF-2Water stains If no depositsWeld dross (per tube length) Up to 3, if <75% of the width of the weld bead.Weld porosity If no liquid penetrant indication.Notes:

(1) Black bottom pit of any depth is not acceptable.(2) After electropolishing, 12” of cumulative length per tube length.

Ra READINGS FOR TUBING

As Drawn and / or Mechanically PolishedRa Average

(Note 1)Ra – Max

Surface Designation µ-in. µ-m µ-in. µ-mSFT1 20 0.5 30 0.75SFT2 25 0.625 35 0.875SFT3 30 0.75 45 1.125

Mechanically Polished and Electropolished, or ElectropolishedRa Average

(Note 1)Ra – Max

µ-in. µ-m µ-in. µ-mSFT4 10 0.25 15 0.375SFT5 15 0.375 25 0.625SFT6 20 0.5 30 0.75Global Stainless Ltd., Tel: + 353 21 4968578 Fax: + 353 21 4312921 e-mail: [email protected]

- 12 -

GENERAL NOTE: All Ra reading are taken across the lay.NOTE:

(1) The average Ra is derived from readings taken at four cross sections approximately 90° apart. No single reading exceeding Ra max.

BPE BIO-TECH & PHARMACEUTICAL FITTINGSGlobal Stainless supplies Bio-Tech and Pharmaceutical Fittings which are designed for use with Automatic Welding Equipment. Long tangents are provided to accommodate all types of Orbital Welding Heads and each Fitting is fabricated to meet the special tolerances required for ovality, wall thickness and squareness.

All GS BPE Fittings comply with the strict requirements of ASME BPE BioProcessing Equipment Standard.

MATERIAL IDENTIFICATION & TRACEABILITY: All GS BPE Fittings are permanently marked with the material heat number, size, grade and the surface finish designation, or material identification number, depending on the size of the fitting. These numbers allow complete traceability of all component material back to the original material supplier.

Material Test Reports (MTR) will be supplied on request. Please specify at time of order if Material Test Reports (MTR) are required.

PACKAGING: All GS BPE Fittings have colour-coded end caps and are packed in sealed transparent plastic bags with a full part designation label attached.

SURFACE FINISHES:

POLISH COMBINATIONCODE

INTERNAL (ID) SURFACE EXTERNAL (OD) SURFACEASME BPESURFACE

DESIGNATION

MAX.SURFACE

ROUGHNESS* SURFACE FINISH

MAX.SURFACE

ROUGHNESS* SURFACE FINISH

µ-in. µ-m µ-in. µ-m3/PC 20 0.5 Mechanical polish - - Unpolished SFF1

7/PL 20 0.5 Mechanical polish 32 0.8 Mechanical polish SFF1

3/PD 15 0.375 Mechanical polish &Electropolish

- - Unpolished SFF4

7/PM 15 0.375 Mechanical polish &Electropolish

32 0.8 Mechanical polish SFF4

ELECTROPOLISHED FITTINGS: All GS BPE Fittings are available electropolished.

CONVERSION OF SURFACE FINISHES: CONVERSION CHART

STANDARDGRIT

Ra RMS

µ-in. µ-m µ-in. µ-mGlobal Stainless Ltd., Tel: + 353 21 4968578 Fax: + 353 21 4312921 e-mail: [email protected]

- 13 -150grit 27-32 0.68-0.80 30-35 0.76-0.89180grit 18-23 0.46-0.58 20-25 0.51-0.64240grit 14-18 0.34-0.46 15-20 0.38-0.51320grit 8-10 0.21-0.25 9-11 0.23-0.28

Grit: Measures the number of scratches per linear inch of abrasive pad. Higher numbers indicate a smoother finish.RMS: Defined as Root Mean Square roughness, the method measures a sample for peaks and valleys. Lower numbers indicate a smoother finish.Ra: Known as the Arithmetic Mean, this measurement represents the average value of all peaks and valleys. Lower numbers indicate a smoother finish.To convert to RMS multiply by 1.11.

TECHNICAL DATA

ASME BPE BIOPROCESSING EQUIPMENTACCEPTANCE CRITERIA FOR INTERIOR SURFACE FINISHES OF FITTINGS

ANOMALY OR INDICATION ACCEPTANCE CRITERIACluster of pits None acceptedDemarcation If <5% of the total area when visually inspected and Ra is met.Grit Lines If Ra is met.Longitudinal welds If polished smooth, blended, and Ra is met.Nicks None accepted.Pits If dia. <0.020” and bottom is shine.Scratches If length <0.25”, depth <0.003”, and Ra is met.Star burst None acceptedSurface cracks None acceptedSurface inclusions If Ra is met and there is no liquid penetrant indication.Surface residuals None accepted.Surface roughness (Ra) See Table SF-4.Water stains If no depositsWeld dross None acceptedWeld porosity None accepted

Ra READINGS FOR FITTINGS

Mechanically PolishedRa Average

(Note 1)Ra – Max

Surface Designation µ-in. µ-m µ-in. µ-mSFF1 15 0.375 20 0.5SFF2 20 0.5 25 0.625SFF3 25 0.625 30 0.75

Mechanically Polished and ElectropolishedRa Average

(Note 1)Ra – Max

µ-in. µ-m µ-in. µ-mSFF4 10 0.25 15 0.375SFF5 15 0.375 20 0.5SFF6 20 0.5 25 0.625

GENERAL NOTE: All Ra readings are taken across the lay.Global Stainless Ltd., Tel: + 353 21 4968578 Fax: + 353 21 4312921 e-mail: [email protected]

- 14 -NOTE:

(1) The average Ra is derived from readings taken at four cross sections approximately 90° apart. Other Ra readings are available if agreed upon between vendor and owner/user. No single reading exceeding Ra max.

BPE BIO-TECH & PHARMACEUTICAL FITTINGSAWF BUTT-WELD - BENDS – FERRULES - CAPS

BPE2S-AWF - 90° TUBE BEND BPE2KS-AWF - 45°TUBE BEND

SIZETUBEO.D.

Amm

Nom.W.T.mm

SIZETUBEO.D.

Amm

Nom.W.T.mm

½” 76.20 1.65 ½” 57.15 1.65¾” 76.20 1.65 ¾” 57.15 1.651” 76.20 1.65 1” 57.15 1.65

1½” 95.25 1.65 1½” 63.50 1.652” 120.6

51.65 2” 76.20 1.65

2½” 139.70

1.65 2½” 85.85 1.65

3” 158.75

1.65 3” 91.95 1.65

4” 203.20

2.11 4” 114.30

2.11

6” 292.10

2.77 6” 158.88

2.77

BPE2CM-AWF- 90°SWEEP ELBOW (CLAMP END – AWF END)

BPE2KM-AWF- 45°SWEEP ELBOW(CLAMP END – AWF END)

Amm

Bmm

SIZETUBEO.D.

Amm

Bmm

½” 76.20 41.28 ½” 57.15 25.40¾” 76.20 41.28 ¾” 57.15 25.401” 76.20 50.80 1” 57.15 28.58

1½” 95.25 69.85 1½” 63.50 36.582” 120.6

588.90 2” 76.20 44.45

2½” 139.70

107.95

2½” 85.73 52.32

3” 158.75

127.00

3” 92.08 60.45

4” 203.20

168.28

4” 114.30

79.25


- 15 -

6” 292.10

266.70

6” 158.75

133.35

BPE14AMP-AWF LONG BUTT-WELD FERRULE BPE16AMP SOLID END CAP

SIZETUBEO.D.

Amm

Bmm

Cmm

SIZETUBEO.D.

Amm

Bmm

½” 44.45

9.40 12.7 ½” 5.00 25.40

¾” 44.45

15.75

19.0 ¾” 5.00 25.40

1” 44.45

22.10

25.4 1” 6.35 50.40

1½” 44.45

34.80

38.1 1½” 6.35 50.40

2” 57.15

47.50

50.8 2” 6.35 63.91

2½” 57.15

60.20

63.5 2½” 6.35 77.40

3” 57.15

72.90

76.2 3” 6.35 90.91

4” 57.15

97.38

101.6

4” 8.00 118.92

6” 76.20

146.86

152.4

6” 11.12 166.88


- 16 -

BPE BIO-TECH & PHARMACEUTICAL FITTINGSAWF BUTT-WELD – TEES – CROSSES – STUBS - CAPS

BPE9W-AWF CROSS

SIZETUBEO.D.

Amm

Bmm

Cmm

Dmm

½” 47.63 95.25 25.40 57.15¾” 50.80 101.6

028.58 60.33

1” 53.98 107.95

28.58 66.68

1½” 60.33 120.65

34.93 73.03

2” 73.03 146.05

41.28 85.73

2½” 79.38 158.75

47.63 92.08

3” 85.73 171.45

53.98 98.43

4” 104.78

209.55

69.85 120.65

6” 142.90

285.80

117.48 181.10

BPE7W-AWF TEE BPE7WS-AWF-SHORT OUTLET TEE

BPE7WM-AWF CLAMP OUTLET TEE


- 17 -

BPE16W-AWF CAP BPE14W-AWF LAB JOINT STUB END

SIZETUBEO.D.

Amm

SIZETUBEO.D.

Amm

Bmm

Cmm

½” 44.45 ½” 50.80 42.96 2.5¾” 46.04 ¾” 50.80 42.86 2.51” 47.63 1” 50.80 50.80 3.3

1½” 52.39 1½” 50.80 73.03 3.32” 69.85 2” 63.50 92.08 3.3

2½” 76.20 2½” 63.50 104.78

3.3

3” 82.55 3” 63.50 127.00

4.2

4” 101.60

4” 63.50 157.16

4.2

6” 127.00

6” 76.20 215.90

5.5

BPE BIO-TECH & PHARMACEUTICAL FITTINGSAWF BUTT-WELD REDUCING TEES

BPE7RW-AWF-REDUCING TEESIZETUBEO.D.

Amm

Bmm

Cmm

Dmm

Emm

Fmm

¾” x ½” 50.80 50.80 101.60

101.60

25.40 63.50

1” x ½” 53.98 53.98 107.95

107.95

28.58 66.68

1” x ¾” 53.98 53.98 107.95

107.95

28.58 66.68

1½” x ½” 60.33 60.33 120.65

120.65

34.93 73.03

1½” x ¾” 60.33 60.33 120.65

120.65

34.93 73.03

1½” x 1” 60.33 60.33 120.65

120.65

34.93 73.03

2” x ½” 73.03 66.68 146.05

133.35

41.28 79.38

2” x ¾” 73.03 66.68 146.05

133.35

41.28 79.38 BPE7RWS-AWF-SHORT OUTLET REDUCING TEE


- 18 -

2” x 1” 73.03 66.68 146.05

133.35

41.28 79.38

2” x 1½” 73.03 66.68 146.05

133.35

41.28 79.38

2½” x ½” 79.38 73.03 158.75

146.05

47.63 85.73

2½” x ¾” 79.38 73.03 158.75

146.05

47.63 85.73

2½” x 1” 79.38 73.03 158.75

146.05

47.63 85.73

2½” x1½”

79.38 73.03 158.75

146.05

47.63 85.73

2½” x 2” 79.38 73.03 158.75

146.05

47.63 85.73

3” x ½” 85.73 79.38 171.45

158.75

53.98 92.08

3” x ¾” 85.73 79.38 171.45

158.75

53.98 92.08

3” x 1” 85.73 79.38 171.45

158.75

53.98 92.08

3” x 1½” 85.73 79.38 171.45

158.75

53.98 92.08 BPE7RWM-AWF-CLAMP OUTLET REDUCING TEE

3” x 2” 85.73 79.38 171.45

158.75

53.98 92.08

3” x 2½” 85.73 79.38 171.45

158.75

53.98 92.08

4” x ½” 104.78

92.08 209.55

184.15

66.68 104.78

4” x ¾” 104.78

92.08 209.55

184.15

66.68 104.78

4” x 1” 104.78

92.08 209.55

184.15

66.68 104.78

4” x 1½” 104.78

92.08 209.55

184.15

66.68 104.78

4” x 2” 104.78

98.43 209.55

196.85

66.68 111.13

4” x 2½” 104.78

98.43 209.55

196.85

66.68 111.13

4” x 3” 104.78

98.43 209.55

196.85

66.68 111.13

6” x 3” 142.88

123.95

285.75

247.65

92.08 136.53

6” x 4” 142.88

130.18

285.75

260.35

95.25 146.05

BPE9RW-AWF REDUCING CROSS BPE7ERW-AWF-ECCENTRIC REDUCING TEE(designed for easy drainage of lines)


- 19 -

BPE BIO-TECH & PHARMACEUTICAL FITTINGSAWF 180° RETURN BENDS WITH WELD END OUTLETS

BPEL29RBW-REDUCING, BOTTOM-OUTLET USE-POINT

(bottom outlet is reducing size)

SIZETUBEO.D.

Amm

Bmm

Cmm

Dmm

¾” x ½” 114.30

57.15 95.25 50.80

1” x ½” 114.30

57.15 95.25 53.98

1” x ¾” 114.30

57.15 95.25 53.98

1½” x ½” 152.40

76.20 114.30

60.33

1½” x ¾” 152.40

76.20 114.30

60.33

1½” x 1” 152.40

76.20 114.30

60.33

2” x ½” 152.40

76.20 127.00

66.55

2” x ¾” 152.40

76.20 127.00

66.55

2” x 1” 152.40

76.20 127.00

66.55

2” x 1½” 152.40

76.20 127.00

66.55

2½” x ½” 190.50

95.25 146.05

73.03

2½” x ¾” 190.50

95.25 146.05

73.03

2½” x 1” 190.50

95.25 146.05

73.03 BPEL29RSW-REDUCING, SIDE-OUTLET USE-POINT(side outlet is reducing size)2½” x

1½”190.5

095.25 146.0

573.03

2½”x 2” 190.50

95.25 146.05

73.03


- 20 -

3” x ½” 228.60

114.30

165.10

79.38

3” x ¾” 228.60

114.30

165.10

79.38

3” x 1” 228.60

114.30

165.10

79.38

3” x 1½” 228.60

114.30

165.10

79.38

3” x 2” 228.60

114.30

165.10

79.38

3” x 2½” 228.60

114.30

165.10

79.38

4” x ½” 304.80

152.40

215.90

92.08

4” x ¾” 304.80

152.40

215.90

92.08

4” x 1” 304.80

152.40

215.90

92.08

4” x 1½” 304.80

152.40

215.90

92.08

4” x 2” 304.80

152.40

215.90

98.55

4” x 2½” 304.80

152.40

215.90

98.55

4” x 3” 304.80

152.40

215.90

98.55


- 21 -

BPE BIO-TECH & PHARMACEUTICAL FITTINGSAWF BUTT-WELD - REDUCERS

BPE31-AWF CONCENTRIC REDUCER(for automatic welding)

BPE32-AWF ECCENTRIC REDUCER(for automatic welding)

SIZETUBEO.D.

Amm

Bmm

CMm

¾” x ½” 101.6 76.2 12.71” x ½” 114.3 88.9 12.71” x ¾” 101.6 76.2 19.0

1½” x ½” 139.7 114.3 12.71½” x ¾” 127.0 101.6 19.01½” x 1” 127.0 101.6 25.42” x ½” 196.9 165.1 12.72” x ¾” 184.2 152.4 19.02” x 1” 184.2 152.4 25.4

2” x 1½” 133.4 101.6 38.12½” x ½” 247.7 215.9 12.72½” x ¾” 235.0 203.2 19.02½” x 1” 235.0 203.2 25.4

2½” x 1½” 184.2 152.4 38.12½” x 2” 139.7 108.0 50.8 BPE31M-AWF CONCENTRIC

REDUCER(clamp end – weld end)

PBE32M-AWF ECCENTRIC REDUCER(clamp end – weld end)

3” x ½” 298.5 266.7 12.73” x ¾” 285.8 254.0 19.03” x 1” 285.8 254.0 25.4

3” x 1½” 235.0 203.2 38.13” x 2” 190.5 158.8 50.8

3” x 2½” 139.7 108.0 63.54” x ½” 406.4 371.5 12.74” x ¾” 393.7 358.8 19.04” x 1” 393.7 358.8 25.4

4” x 1½” 342.9 308.0 38.14” x 2” 298.5 263.5 50.8

4” x 2½” 247.7 212.7 63.54” x 3” 196.9 161.9 76.26” x 3” 247.7 222.3 76.26” x 4” 254.0 228.6 101.6


- 22 -

BPE BIO-TECH & PHARMACEUTICAL FITTINGSCLAMP END ELBOWS – TEES - CROSSES

BPE2CMP - 90° ELBOW BPE2KMP - 45° ELBOW

SIZETUBEO.D.

Amm

Rmm

SIZETUBEO.D.

Amm

Rmm

½” 41.15 19.0 ½” 25.4 19.0¾” 41.15 28.6 ¾” 25.4 28.61” 50.80 38.1 1” 28.6 38.1

1½” 69.85 57.2 1½” 36.6 57.22” 88.90 76.2 2” 44.5 76.2

2½” 108.0 95.3 2½” 52.3 95.33” 127.0 114.3 3” 60.5 114.34” 168.2 152.4 4” 79.3 152.46” 266.7 228.6 6” 133.4 228.68” 327.0 304.8 8” 139.7 304.8

10” 403.2 381.0 10” 168.3 381.0

SIZETUBEO.D.

Amm

Bmm

Cmm

BPE9MP - CROSS

½” 57.2 114.3 25.4¾” 60.3 120.6 28.61” 66.7 133.4 28.6

1½” 73.0 146.0 34.92” 85.7 171.5 41.3

2½” 92.1 184.2 47.63” 98.4 196.9 54.04” 120.7 241.3 69.96” 181.0 362.0 117.58” 174.6 349.3 127.010” 212.7 425.5 152.4

BPE7MP – TEE BPE7SMP – SHORT OUTLET TEE


- 23 -

BPE BIO-TECH & PHARMACEUTICAL FITTINGSCLAMP END REDUCING TEES & CROSSES

BPE7RMP-REDUCING TEESIZETUBEO.D.

Amm

Bmm

Cmm

Dmm

Emm

(reducing size on branch)

¾” x ½” 63.50 63.50 127.00 127.00 25.401” x ½” 66.68 66.68 133.35 133.35 28.581” x ¾” 66.68 66.68 133.35 133.35 28.58

1½” x ½” 73.03 73.03 146.05 146.05 34.931½” x ¾” 73.03 73.03 146.05 146.05 34.931½” x 1” 73.03 73.03 146.05 146.05 34.932” x ½” 79.38 85.73 171.45 158.75 41.282” x ¾” 79.38 85.73 171.45 158.75 41.282” x 1” 79.38 85.73 171.45 158.75 41.28

2” x 1½” 79.38 85.73 171.45 158.75 41.282½” x 1” 85.73 92.08 184.15 171.45 47.63

2½” x 1½” 85.73 92.08 184.15 171.45 47.632½” x 2” 85.73 92.08 184.15 171.45 47.63

BPE7SMP-SHORT OUTLET REDUCINGTEE (reducing size on branch)

3” x 1” 92.08 98.43 196.85 184.15 54.003” x 1½” 92.08 98.43 196.85 184.15 54.00

3” x 2” 98.43 98.43 196.85 196.85 54.003” x 2½” 98.43 98.43 196.85 196.85 54.004” x 1” 104.78 120.65 241.30 209.55 66.68

4” x 1½” 104.78 120.65 241.30 209.55 66.684” x 2” 111.13 120.65 241.30 222.25 66.68

4” x 2½” 111.13 120.65 241.30 222.25 66.684” x 3” 111.13 120.65 241.30 222.25 66.686” x 3” 136.53 181.00 361.95 273.05 92.086” x 4” 146.05 181.00 361.95 292.10 95.258” x 4” 174.63 174.63 349.25 349.25 120.658” x 6” 174.63 174.63 349.25 349.25 127.00

10” x 6” 212.73 200.03 400.05 425.45 152.4010” x 8” 212.73 200.03 400.05 425.45 152.40

BPE9RMP REDUCING CROSS BPE7REMP- ECCENTRIC REDUCING TEE(reducing size on branch)


- 24 -

BPE BIO-TECH & PHARMACEUTICAL FITTINGSGlobal Stainless Ltd., Tel: + 353 21 4968578 Fax: + 353 21 4312921 e-mail: [email protected]

- 25 -

CLAMP END ADAPTERS CLAMP END REDUCERS

SIZETUBEO.D.

Amm

Bmm

BPE21 RMP &

BPE22RMP

REDUCINGADAPTERS

BPE21RMP

SIZETUBEO.D.

Amm

CLAMP ENDREDUCERS

BPE31-14MPCONCENTRIC REDUCER

½” x ½” 50.80 50.80 ¾” x ½” 50.80½” x ¾” 50.80 41.28 1” x ½” 63.50½” x 1” 50.80 41.28 1” x ¾” 50.80¾” x ¾” 50.80 54.00 1½”x ½” 88.90¾” x 1” 50.80 46.00 1½”x ¾” 76.201” x ½” 55.56 41.28 1½”x 1” 76.201” x ¾” 55.56 41.28 2” x ½” 139.701” x 1” 57.15 41.28 2” x ¾” 127.00

1” x1½" 50.80 54.00 2” x 1” 127.001” x 2” 66.68 57.15 2” x 1½” 76.20

1½” x ½” 55.56 41.28 2½”x 1” 177.801½” x ¾” 55.56 41.28 2½”x 1½” 127.001½” x 1” 57.15 41.28 2½”x 2” 76.201½” x1¼” 61.98 57.15 3” x 1” 228.601½” x 1½” 61.98 57.15 3” x 1½” 177.801½” x 2” 66.68 57.15 3” x 2” 127.002” x ½” 55.56 50.80

BPE22RMP3” x 2½” 76.20 BPE32-14MP ECCENTRIC

REDUCER2” x ¾” 55.56 54.00 4” x1“ 333.382” x 1” 57.15 54.00 4” x 1½” 282.582” x 1¼" 62.70 54.00 4” x 2” 231.782” x 1½” 62.70 57.15 4” x 2½” 180.982” x 2” 67.56 59.53 4” x 3” 130.18

2” x 2½” 79.38 61.12 6” x 3” 190.502½” x 1½” 70.64 57.15 6” x 4” 193.682½” x 2” 70.64 59.53 8” x 4” 190.50

2½” x 2½” 83.34 66.68 8” x 6” 196.852½” x 3” 88.90 53.18 10” x 6” 222.253” x 2” 88.90 59.53 10” x 8” 222.253” x 3” 88.90 73.034” x 3” 96.84 55.56

OTHER SIZES AVAILABLE ON REQUEST4” x 4” 96.84 76.206” x 6” 127.0 98.42

BPE BIO-TECH & PHARMACEUTICAL FITTINGSSPECIAL CONICAL ADAPTOR


- 26 -

CLAMPSIZE

A

CLAMPSIZE

B

INSIDEDIM.

C

LENGTH

D

SPECIAL CONICAL ADAPTOR

¾” ½” 9.40 31.751” ½” 9.40 31.75

1½” ½” 9.40 31.752” ½” 9.40 31.75

2½” ½” 9.40 31.753” ½” 9.40 31.754” ½” 9.40 31.75

1” ¾” 15.75 31.751½” ¾” 15.75 31.752” ¾” 15.75 31.75

2½” ¾” 15.75 31.753” ¾” 15.75 31.754” ¾” 15.75 31.75

1½” 1” 22.10 31.752” 1” 22.10 31.75

2½” 1” 22.10 31.753” 1” 22.10 31.754” 1” 22.10 31.75

2” 1½” 34.80 31.752½” 1½” 34.80 31.753” 1½” 34.80 31.754” 1½” 34.80 31.75

2½” 2” 47.50 31.753” 2” 47.50 31.754” 2” 47.50 31.75

3” 2½” 60.20 31.754” 2½” 60.20 31.75

4” 3” 72.90 31.754” 4” 98.30 31.75

BPE14MPHR RUBBER HOSE ADAPTER


- 27 -

SIZETUBEO.D.

Amm

Bmm

Cmm

½” 38.10 9.40 12.70¾” 38.10 15.75 19.051” 42.86 21.18 25.40

1½” 42.86 33.88 38.102” 58.74 46.58 50.80

2½” 50.80 59.28 63.503” 78.42 71.98 76.204” 86.52 97.38 101.66” 101.6 146.86 152.4

BPE BIO-TECH & PHARMACEUTICAL FITTINGSO.D. CLAMPS

GS LINK CLAMP GS 2-PIECE CLAMP

SIZETUBEO.D.

Amm

SIZETUBEO.D.

Amm

½” -¾” 28.3 10” 277.01” - 1.5” 1½” 12” 327.5

2” 67.02½” 80.53” 94.04” 122.06” 175.08” 226.0

13MHH - HEAVY CLAMP 13MHP HIGH PRESSURE CLAMP

SIZETUBEO.D.

Amm

SIZETUBEO.D.

Amm

Not recommended for use with1” Fittings.

½” -¾” 28.21” - 1.5” 53.6 1½” 52.0

2” 67.0 2” 65.52½” 80.6 2½” 79.03” 94.2 3” 92.54” 122.2 4” 120.56” 170.4 6” 170.0


- 28 -

13MHHM - HEAVY CLAMP 3-PIECE CLAMP

SIZETUBEO.D.

Amm

SIZETUBEO.D.

Amm

½” -¾” 28.21” - 1.5” 53.6 1” - 1.5” 53.9

2” 67.0 2” 67.42½” 80.6 2½” 80.93” 94.0 3” 94.44” 122.0 4” 122.46” 175.08” 226.0

See Technical Data for Temperature / Pressure Ratings on all of the above clamps.

TECHNICAL DATA – O.D. CLAMPS

GS LINK CLAMP

PRESSURE RATING (psi) - with wing nut tightened to 25in-lb of torqueTEMPERATURE ( °F) (°C)

SIZE TUBE O.D.½” - ¾” 1”-1.5” 2” 2.5” 3” 4” 6” 8”

70 21 1500 500 450 400 350 200 150 100250 121 1200 250 250 200 150 125 75 50

GS 2-PIECE CLAMP

PRESSURE RATING (psi) - with wing nut tightened to 25in-lb oftorque

TEMPERATURE ( °F) (°C)

SIZE TUBE O.D.10” 12”

70 21 200 200250 121 100 100

13MHH – HEAVY CLAMP


SIZE TUBE O.D.½” - ¾” 1”-1.5” 2” 2.5” 3” 4”

70 21 1500 500 450 400 350 200250 121 1200 250 250 200 150 125

13MHP – HEAVY CLAMP (not recommended for use with 1” Fittings).

PRESSURE RATING (psi) - with wing nut tightened to 20ft-lb of torqueTEMPERATURE ( °F) (°C)

SIZE TUBE O.D.1.5” 2” 2.5” 3” 4” 6”

70 21 1500 1000 1000 1000 1000 300


- 29 -

250 121 1200 800 800 800 800 200

13MHHM – HEAVY CLAMP


SIZE TUBE O.D.½” - ¾” 1”-1.5” 2” 2.5” 3” 4” 6” 8”

70 21 1500 500 450 400 350 200 150 100250 121 1200 250 250 200 150 125 75 50

3-PIECE CLAMP


SIZE TUBE O.D.½” - ¾” 1”-1.5” 2” 2.5” 3” 4”

70 21 600 550 450 350 350250 121 300 275 225 160 150

To convert Pressure values from psig to kPa use the following formula: psi x 6.895 = kPa (approx).Example: 200psi x 6.895 = 1379kPa.

HEX HANGERS & ACCESSORIESGS24FCF-1 HEX HANGER 2-PIECE GS24FCF-2 HINGED HANGER WITH

Ø12 ROD(optional rod lengths available)

SIZETUBEO.D.

Amm

SIZETUBEO.D.

Amm

Bmm

1” 25.4 1” 25.4 75.01½” 38.1 1½” 38.1 81.52” 50.8 2” 50.8 88.0

2½” 63.5 2½” 63.5 94.53” 76.2 3” 76.2 100.54” 101.6 4” 101.6 113.5

104mm 104.0 104mm 104.0 114.5


- 30 -

GS24FCF-3 HINGED HANGER WITH ½" BSP BOSS

GS24FCF-4 HINGED HANGER WITH M12 THREADED ROD(optional rod lengths available)

SIZETUBEO.D.

Amm

Bmm

SIZETUBEO.D.

Amm

Bmm

1” 25.4 47.0 1” 25.4 75.01½” 38.1 53.5 1½” 38.1 81.52” 50.8 60.0 2” 50.8 88.0

2½” 63.5 66.5 2½” 63.5 94.53” 76.2 72.5 3” 76.2 100.54” 101.6 85.5 4” 101.6 113.5

104mm 104.0 86.5 104mm 104.0 114.5

GS24FCF-5 U-BOLT HANGER GS25EP WALL FLANGE

SIZETUBEO.D.

Amm

SIZETUBEO.D.

Amm

Bmm

½” 15.88¾” 22.231” 31.75 1” 127.0 28.6

1½” 44.45 1½” 127.0 41.32” 57.15 2” 127.0 54.0

2½” 69.85 2½” 127.0 66.73” 82.55 3” 152.4 79.44” 107.95 4” 177.8 104.86” 158.75

ROUND HANGERS & ACCESSORIES

GS24FCF-6 ROUND HANGER WITH 3/8” NPT BOSS & INSERT

GS24FCF-7 ROUND HANGER WITH M12 THREADED ROD & INSERT(optional rod lengths available)

SIZETUBEO.D.

Amm

Bmm

SIZETUBEO.D.

AMm

Bmm

½” 12.7 51.0 ½” 12.7 75.5¾” 19.0 51.0 ¾” 19.0 75.51” 25.4 51.0 1” 25.4 82.0

1½” 38.1 57.0 1½” 38.1 88.02” 50.8 63.5 2” 50.8 94.5


- 31 -2½” 63.5 70.0 2½” 63.5 101.03” 76.2 76.0 3” 76.2 107.04” 101.6 89.0 4” 101.6 120.0

GS24FCF-8 ROUND HANGER WITH ½” BSP BOSS & INSERT

GS24FCF-9 ROUND HANGER WITH Ø12 ROD & INSERT(optional rod lengths available)

SIZETUBEO.D.

Amm

Bmm

SIZETUBEO.D.

AMm

Bmm

½” 12.7 47.5 ½” 12.7 75.5¾” 19.0 47.5 ¾” 19.0 75.51” 25.4 54.0 1” 25.4 82.0

1½” 38.1 60.0 1½” 38.1 88.02” 50.8 66.5 2” 50.8 94.5

2½” 63.5 73.0 2½” 63.5 101.03” 76.2 79.0 3” 76.2 107.04” 101.6 92.0 4” 101.6 120.0

GS24FCF-10 ROUND HANGER WITH M12 BOSS & INSERT

OPTIONAL WALL/CEILING MOUNTINGPLATES WITH BOLT HOLES

SIZETUBEO.D.

Amm

Bmm

GS26-1 PLATE WITH M12 BOSS

GS26-2 PLATE WITH ROD

½” 12.7 35.5¾” 19.0 35.51” 25.4 42.0

1½” 38.1 48.02” 50.8 54.5

2½” 63.5 61.03” 76.2 67.04” 101.6 80.0


- 32 -

US3A & BS STANDARD FERRULESGS14AMP BUTT WELD FERRULE

SIZETUBEO.D.

Amm

Bmm

Cmm

Dmm

Emm

Fmm

½” 9.4 12.7 28.6 12.7 21.5 76.2¾” 15.7 19.0 28.6 12.7 21.5 76.21” 22.1 25.4 28.6 12.7 21.5 76.2

1½” 34.8 38.1 28.6 12.7 21.5 76.22” 47.5 50.8 28.6 12.7 21.5 76.2

2½” 60.2 63.5 28.6 12.7 21.5 76.23” 72.9 76.2 28.6 12.7 21.5 101.64” 97.4 101.6 28.6 15.8 21.5 101.66” 146.9 152.4 38.1 22.4 28.6 152.4

GS14WMP SHORT WELD FERRULE

GS BS4825 PART 3 BUTT WELD FERRULE

GS14WLMP LIGHT BUTT WELD FERRULE

GS 14MPW


- 33 -

HEAVY BUTT WELD FERRULE

OTHER FERRULE SIZES AVAILABLE ON REQUEST

SIZETUBEO.D.

Amm

Bmm

Cmm

1” 21.7 29.5 41.11½” 34.4 42.6 41.12” 47.1 55.7 44.5

2½” 59.8 68.8 44.53” 72.5 81.9 46.04” 96.8 108.

153.8

6” 146.3

157.3

63.5

BPE GASKETS FOR CLAMP END FITTINGS

BPE GASKETS – TYPE 1 STANDARD ½” & ¾”

BPE GASKETS – TYPE 2 FLANGED 1” – 12”

SIZETUBEO.D.

Amm

Bmm

SIZETUBEO.D.

AMm

Bmm

½” 21.8 9.9 1” 52.7 22.8¾” 21.8 16.3 1½” 52.7 35.8

2” 66.2 48.82½” 79.7 60.53” 93.2 73.14” 121.2 97.8

BPE GASKETS – TYPE 1 STANDARD 1” – 8” 6” 169.1 148.01” 50.0 22.7 8” 220.0 199.0

1½” 50.0 35.9 10” 270.7 249.02” 63.5 48.6 12” 321.5 300.0

2½” 76.2 61.33” 88.9 74.04” 118.0 98.66” 165.0 147.88” 216.0 196.6

GASKET MATERIAL PROPERTIES

EPDM TEFLON BUNA-N VITON SILICONE


- 34 -

PROPERTY 40MP-E 40MP-G 40MP-U 40MP-V 40MP-XTemperature range -55°F to

275°F -40°F to450°F

-40°F to225°F

-20°F to400°F

-80°F to450°F

Acid Resistance Good-Excellent

Excellent Good Good Good

Alkali Resistance Good-Excellent

Excellent Fair-Good Poor-Good Poor-Fair

Petroleum Oil Resistance

Poor Excellent Excellent Excellent Good

Vegetable Oil Resistance

Good Excellent Good Excellent Good

Abrasion Resistance Good-Excellent

Excellent Good Good Good-Excellent

Compression Set Fair Cold Flows Good Good-Excellent

Good-Excellent

SMART GASKETSWe also offer the Smart Gasket line of specialty gaskets for use with Smart Clamps. These Gaskets install between two standard sanitary flanges and allow the use of sensors (thermocouples) and spore traps (details on application).

SCREEN GASKETSFluid conditioning gaskets are available in a wide variety of meshes and materials (reference chart available on application)

ORIFICE PLATESOrifice gaskets are available in many materials (details on application)

BPE GASKETSAVAILABLE GASKET MATERIALS

Buna-N (Black or White)• Least expensive elastomer gasket• Nitrile compound is very elastic making for a leak proof connection• Good chemical resistance for use with petroleum solvents, alcohol etc.• 3A qualified• Meets 21CFR 177.2600• Useful temperature range from -40°F to 225°F (-40°C to 107°C)Teflon (PTFE)• Commonly used for food and pharmaceutical applications• Excellent chemical resistance• Not suitable for great temperature fluctuations, Teflon tends to cold flow and will not return to its


- 35 -

original shape.• 3A qualified• Meets 21CFR 177.2600• Passes cytotoxicity testing• Pharmaceutical Class VI approved• Useful temperature range from -110°F to 400°F (-79°C to 204°C)Silicone (Platinum cured)• 3A qualified• Meets 21CFR 177.2600• Passes cytotoxicity testing• Pharmaceutical Class VI approved• Useful temperature range from -20°F to 450°F (-29°C to 232°C)Silicone (Peroxide cured)• 3A qualified• Meets 21CFR 177.2600• Passes cytotoxicity testing• Pharmaceutical Class VI approved• Useful temperature range from -20°F to 450°F (-29°C to 232°C)Viton (Flourel)• 3A qualified• Meets 21CFR 177.2600• Passes cytotoxicity testing• Pharmaceutical Class VI approved• Useful temperature range from -20°F to 450°F (-29°C to 232°C)EPDM• 3A qualified• Meets 21CFR 177.2600• Passes cytotoxicity testing• Pharmaceutical Class VI approved• Useful temperature range from -55°F to 275°F (-48°C to 135°C)Tef Steel• Does not cold flow (creep), retains shape and seal properties• Excellent chemical resistance• Steam resistance• Minimal thermal expansion• Teflon & PM316L• 3A qualified• Meets 21CFR 177.2600• Passes cytotoxicity testing• Pharmaceutical Class VI approved• Useful temperature range from -110°F to 400°F (-79°C to 204°C)


steriboreä bpe high purity astm a270 316l · 2014-08-01 · steribore bpe high purity astm a270...

Documents