Customer

Statement of Compliance

on the A-Design Assessment Registration No.

44 220 14555130a-DA-GL, Rev. 2

GE Energy GmbH Holsterfeld 16

48499 Salzbergen GERMANY

GE 1.79-100, Wind Turbine GE48.7C/C2, GE48.7G1, GE48.7G2, LM48.7P

HH 79.7 m, 50/60 Hz STW-CWE

with the characteristic data given in the attached "Annex to Design Assess ment "

has been assessed by TUV NORD concerning the design.

Asses sed acc. to WTGS Class IEC S

The design approval is based on the indicated documents as follows:

TOV NORD Report No. 8111 555 130-1 Ell TOV NORD Report No. 8111 555 130-1 Elli TOV NORD Report No. 8111 555 130-1 EVIi TOV NORD Report No. 8111555130-1 EIV TOV NORD Report No. 8111 555 130-1 EV TOV NORD Report No. 8106 951 790-2 E TOV NORD Report No. 8108 007 661-3 E TOV NORD Report No. 8108 805 454-3 E TOV NORD Report No. 8108 142 045-3 E TOV NORD Report No. 8110 907 395-3 E TOV NORD Report No. 8108 543 929-3 E TOV NORD Report No. 8110 907 395-4 E TOV NORD Report No. 8000 198 463-5 E TOV NORD Report No. 8106 703 224-5 E TOV NORD Report No. 8108 007 661-6 El TOV NORD Report No. 8000 198 463-12 E TOV NORD Report No. 8108 007 661-9

Load Assumptions Blade G1 (60Hz) Load Assumptions Blade C/C2 (60Hz) Load Assumptions Blade G2 (60Hz) Load Assumptions Blade LM (60Hz) Load Assumptions Amend. (50Hz) Safety Concept and Manuals Rotor Blade GE48.7C Rotor Blade GE48.7C2 Rotor Blade GE48.7G1 Rotor Blade GE48. 7G2 Rotor Blade LM48.7P Machinery Components Electrical Systems (60Hz) Electrical Systems (50Hz) Tubular steel tower , hh 79.7 m Nacelle Cover and Spinner Commissioning

Rev.2 dated Feb 2015 Rev.3 dated Feb 2015 Rev.a dated Feb 2015 Rev.2 dated Feb 2015 Rev.2 dated Feb 2015 Rev.10 dated Feb. 2015 Rev.2 dated Feb. 2015 Rev.5 dated Feb. 2015 Rev. 7 dated Feb. 2015 Rev.1 dated Feb. 2015 Rev.5 dated Apr. 2015 Rev.4 dated Feb 2015 Rev.14 dated Nov. 2014 Rev.19 dated Nov. 2014 Rev.6 dated Apr. 2015 Rev.7 dated Nov. 2014 Rev.a dated May 2012

Page 1 of 2

PLEASANT RIDGE EXHIBIT 130C

Normative references: Certification scheme: Germanischer Lloyd WindEnergie GmbH " Guideline for the Certification of Wind Turbines" , Edition 2003 with Supplement 2004 in combination with IEC 61400-1 "Wind turbine generator systems - part 1: Safety requirements " , Second Edition , 1999-02 (only for loads) and GL Wind - Technical Note 067, Certification of Wind Turbines for Extreme temperature (here: Cold Climate), Scope of Assessment , Ed. 2009, Rev.3

Any change in the design is to be approved by TUV NORD. Without approval this Statement loses its val idity.

TOV NORD CERT GmbH

Dipl.-l ng. Werner Petruschlte

Langema rckstral1e 20 • 45141 Essen • email:windenergy@ tuev-nord.de

Statement of Compliance on the A-Des ig n Assessment Reg istrati on-No. 44 220 14555130a-DA-GL, Rev . 2

Essen, 201" April 2015

Page 2 of 2

Principle technical turbine data of the GE 1. 79-100, GE48.7C/C2, GE48.7G1, GE48.7G2, HH79. 7m, 50/60Hz (STW I CWE)

Main data

Nacelle

Type

Rotor diameter Power regulation

Rated power Hub height Rated rotational speed Operating range rotational speed Cut-in wind speed Rated wind speed Cut-out-wind speed (10 min mean) Extreme wind speed (50-year, 10 min average, Vret)

Annual average wind speed K-Weibull Longitudina l turbulence intensity at 15 m/s (l1s) Wind shear a

Design life time IEC 61400-1, class

Air density Ambient Temperatures

Air density

Ambient Temperatu res

Design GE drawing No.

alternative Design GE drawing No. alternative Design GE drawing No.

Annex to A-Design As sessmen t No. 44 220 14555130a-DA-GL, Rev. 2

Horizonta l axis wind turbine with variable roto r speed 100 m Independent electromechanical pitch system for each blade 1790 KW 79.7 m 16.42 rpm 9.58 . .. 17.80 rpm 3.0 m/s 10.2 m/s 22 m/s 37.5 m/s

9.12 m/s 2.47

12.5% 0.22 /0.11

20 years s

STW conditions 1.15 kg/m3 (at 15°C) -15 °C to +40 °C (Ope ration) T min. start= -10 °C -20 °C to +50 °C (Surv ival) +15 °C (Annual average)

CWE conditions 1.19 kg/m3 (at 5°C) 1.362/1.421 kg/m3 (at -30°C/-40°C) -15 °C to +40 °C (Operat ion) -30 °C to -15 °C (Derated Operat ion) -40 °C to +50 °C (Survival ) +5 °C (Ann ual average)

GE Energy 123W2034

GE Energy 108W63 44

GE Energy 115W5223

Page 1 of~

Rotor

Rotor blade

Cone angle Tilt Blade pitch angle Orientation

Design Type Material

Blade length Number of Blades GE Drawing No.

alternative Design Type Material

Blade length Number of Blades GE Drawing No.

alternative Design Type Material Blade length Number of Blades GE Drawing No.

3.0° 4.0° Variab le Upwind

GE Energy GE48. 7C (Gurit) Glass fibre reinforced epoxy resin, carbon fibre spar cap 48.7 m 3 103W3724 109W4874 (VGs) 103W3050 (with serrations)

GE Energy GE48. 7C2 (Zoltek) Glass fibre reinforced epoxy resin, carbon fibre spar cap 48.7 m 3 103W3725 109W4874 (VGs) 103W3723 (with serrations)

GE Energy GE48.7g1 E-Glass fibre reinforced epoxy resin 48.7 m 3 103W1687* 109W4700 ( with VGs) 103W2994 (serr)

*Loads include impact of serrat ion and vortex generator

alternative Design Type Material

GE Energy GE48.7G2 E-Glass fibre reinforced epoxy resin with Heavy E-Glass fibre reinforced epoxy resin spar cap and blade root

Blade length 48.7 m Number of Blades 3 GE Drawing No. 109W3195 Rev. A* *Loads include impact of serration and vortex generator

Annex to A-Design Assessment No. 44 220 14555130a-DA-GL, Rev. 2

Page 2 of(fj-

Lightning protection

Pitch System 60Hz (Pitch Axis)

Pitch System 50Hz (Pitch Axis)

Pitch System (Pitch Battery)

Pitch System (Pitch Motor)

alternative Design I Manufacturer LM W ind Power Type LM 48 .7 P Material Fibre reinforced plastics Blade length 48. 7 m Number of blades 3 Drawing No. DR-01022/A5 P07390 GE Designation 109W4956 *Loads include impact of serration and vortex generator

Class

Design Vendor designation

GE designation

Design Vendor designation

GE designation

Design Vendor designation GE des ignation

Design Vendor designation

GE designation

alternative Design Vendor designation

GE designation

1

GE Energy 151X1246CA02SA01/02 (Pitch Axis 1 Assembly) 151X1246CA02SA03/04 (Pitch Axis 2/3 Assembly)

108W3157P001-P002 (Pitch Axis 1 Assemb ly) 108W3158P00 1-P002 (Pitch Axis 2/3 Assembly )

GE Energy 151X 1246CA02SA01 (Pitch Axis 1 Assembly) 151X1246CA02SA03 (Pitch Axis 2/3 Assemb ly)

108W3157P001 (Pitch Axis 1 Assembly) 108W3158P001 (Pitch Axis 2/3 Assemb ly

Enersys 151X1233CB02SA01 I X16 (Battery Assemb ly) 104W9342P001 (Battery Assembly)

GE Salem 5BT13568002 (Motor Assembly) 5BT13568003 (Motor Assemby) 108W5453P001 (Motor Assembly) 108W5453P002 (Motor Assembly)

Advanced Motor & Drive FP9-4001 (Motor Assemb ly) FP2-4002 (Motor Assemby) 104W9343P002 (Motor Assembly) 104W9343P003 (Motor Assemb ly

Annex to A-Design Assessment No. 44 220 14555130a -DA-GL , Rev . 2

Page 3 of(f vf

Pitch bearing Manufacturer GE Energy Type Ball bearing slewing ring GE designation 200W0612G001-G012

alternative Manufacturer GE Energy Type Ball bearing slewing ring GE designation 200W0688GOO 1-G006

alternative (onl't. for CIC2 60Hzl Manufacturer GE Energy Type Ball bearing slew ing ring GE designation 103W3177G001-G003

Pitch drive Manufacturer Liebherr-We rk Biberach GmbH Type 3-stage planetary gearbox Vendor des ignation 90008518 GE designation 107W3331 P001

alternative Manufacturer Nanjing High Speed Gear Manufacturer Co., Ltd Type 3-stage planetary gearbox Vendor designation FDX104A-01-00R1 GE designation 123W1837P001

alternative Manufacturer S.MEl :I srl (Rossi) Type 3-stage planetary gearbox Vendor designation RES 1300 GR3S-133-1 OS-RT D-CW GE designation 107W3332P001

alternative Manufacturer Nanjing High Speed Gea r Manufactur er Co., Ltd Type 3-stage planetary gearbox Vendor designation FDX104A-01-00R2 GE designation 109W5423P00 1

Rotor Hub Design GE Energy Type Cast Part Material EN-GJS-400-18U-L T GE drawing No. 103W317 4 (mach ining)

115W1908 (casting)

Hub cover Manufacturer GE Energy GE drawing No. 103W3 150

Ann ex to A-D esign Assess ment No . 44 220 14555130a-DA-GL, Rev. 2

Page 4 o(Jr

Main Bearing Manufacturer NTN Walz lager GmbH Type Double Row Spherica l Roller Beari ng Vendor designation 240/7 1 OBV2S30 GE designation 108W4543P001

alternative Manufacturer Koyo Jtekt Corporation Type Double Row Spherical Roller Bear ing Vendor designation 240/7 10RHAW33TCS FYPO GE designat ion 108W4543POO 1

Main Bear ing Hous ing Design GE Energy GmbH Type Cast Part Material EN-GJS-400- 18U-L T GE drawing No. 103W3164 (machin ing)

103W3037 (casting)

Main Shaft Manufacturer GE Energy Type forged part Material 34CrNiMo6 GE drawing No. 103W2967 Rev.C

Low sp eed shaft rotor lock device Design GE Energy

Type forged part Material E360, 039 0 grade D GE draw ing No. 115W4450 (hole disk)

102W 1452 ( bolt)

High speed shaft rotor lock device Design GE Energy

Type forged part Material 0345 grade D GE drawing No. 115W7394

Gearbox Pedestal Mounts Manufacturer GE Energy

Type cast part Vendo r designation EN-GJS-400- 1 SU-LT GE designation 103W1872

Ann ex to A-Design As sessment No. 44 220 14555130a-DA-GL, Rev. 2

Gearbox Elastomer Bearing

Gearbox 60 Hz

Manufacture r

Type Vendor designation GE designation

Manufacturer

Type Vendor designation GE designation Gear ratio

alternative Manufacturer Type Vendor designation GE designation Gear ratio

alternative Manufacturer Type Vendor designation GE designation Gear ratio

alternative Manufacturer Type Vendor designation GE designation Gear ratio

alternative Manufacturer Type Vendor designation GE designati on

Gear ratio

Annex to A -Design Assessment No. 44 220 14555130a-DA-GL, Rev. 2

ESM Energie- und Schwingungstechnik Mitsch GmbH Elastomer bearing UB97 _003_60_60 108W7489

Nanjing High Speed Gear Manufacturer Co., lt d Planetary-hel ical gearbox FDMD-OOR1 108W5166P001 89.47

Bosch RexrothAG Planetary-helical gearbox GPV 457.1 S 109W2458P001 (PALL) 89.252

Winergy AG Planetary-helical gearbox PEAS 4431 108W6862P001 89.51

Bosch Rexroth AG Planetary-helical gearbox GPW457.3 S 109W6242P001 & 109W6246P001 89.25

Bosch Rexroth AG Planetary-he lical gearbox GPW45 7.0 S 108W6864P001 (HYDAC) 109W1058P001 (PALL) 89.252

Gearbox 50 Hz

alternative Manufacturer Type Vendor designation GE designation Gear ratio

alternative Manufacturer Type Vendor designation GE designation Gear ratio

alternative Manufacturer Type Vendor designation GE designation Gear ratio

alternative Manufacturer Type Vendor designation GE designation Gear ratio

Manufacturer Type Designation GE des ignation Gear ratio

alternative Manufactu rer Type Designation GE designation Gear ratio

alternative Manufacturer Type Designation GE designation Gear ratio

Annex to A-Design Assessment No. 44 220 14555130a-DA -GL, Rev. 2

Wine rgy AG Planetary-helical gea rbox PEAS 4431 .0 - 1.558.398 109W6241 POO 1 & 109W6245POO 1 89.51

Nanjing High-Speed & Accu rate Gear Group Planetary-hel ical gearbox FDMD-OOR3 123W3011 P001 (876kNm) 89.47

Nanjing High-Speed & Accurate Gear Group Planetary-helical gearbox FDMD-OOR38 109W6240P001 (924 kNm) 89.47

Nanj ing High-Speed & Accu rate Gear Group Planeta ry-he lical gearbox FDMD-OOR4 109W6244P001 (953 kNm) 89.47

Nanjing High Speed Gear Manufacturer Co ., Ltd Planeta ry-helica l gearbox FDME-OOR1 108W52 62P001 111.54

Bosch Rexroth AG Planetary-helical gearbox GPV 457 .0 S 108W6863P00 1 111.720

Winergy AG Planetary-helical gearbox PEAS 4431 108W686 1 POO 1 111.296

Rotor Brake

Generator Coupling

alternative Manufacturer Type Designation GE designation Gear ratio

alternative Manufacturer Type Vendor designation GE designati on Gear ratio

alternative Manufacturer Type Vendor designation GE designation

Gear ratio

Manufacturer Type Vendor designation GE designation

alternative (only 60Hz) Manufa cturer Type Vendor des ignat ion GE designati on

Manufacturer Vendor designation Main drawing No.

GE designation

alternative Manu facturer Vendor designation Main drawing No.

GE designation

Annex to A-Des ign Assessment No . 44 220 14555130a -DA-GL , Rev. 2

Winergy AG Planetar y helica l gea rbox PEAS 4431 .0 - 1.560.076 109W6565P0 01 & 109W6569P001 111.296

Nanjing High-Speed & Acc urate Gear Group Planetary- helica l gearbox FDME-OOR3 123W3012 P001 (876 kNm) 111.54

Nanjing High-Speed & Accurate Gea r Group Planetary-heli cal gearbox FDME- OOR4 109W6568P001 (953 kNm) 109W6562P001 (925 kNm) 89.47

Svendbo rg Bra kes A/S Active hydraulic brake BSAK 3000-MS40S-103 392A 1046 (Caliper) 109W2061P0 01 (HPU - 60 Hz) 109W2061 P002 (HPU - 50 Hz)

Hydrep Inc . Active hydraulic brake HWPN 087 103W230 1 (Caliper ) 103W2302 (HPU)

Winergy AG ARPEX ARS-4 KRZK 479-4 ARS04-04 79-104 7 (60 Hz) ARS04-0479-1048 (50 Hz) 108W5503P001 (60Hz) 108W5501P001 (50Hz)

KTR Kupplungstechnik GmbH Radex-N 165 NANA 4 522706 Index O (60Hz) 523113 Index O (50Hz) 108W550 0P001 (60Hz) 108W5502P001 (50Hz)

Page 8 ovif(

Bed plate

Generator Frame

Yaw bearing

Yaw drive

Design Type Material GE drawing No.

Design Type Material GE drawing No.

Manufacturer Type GE designation

alternative Manufacturer Type GE designation

Manufacturer

Type Vendor designation

GE designation

Motor

alternative Manufacturer Type Vendor designation

GE designation

Motor

alternative Manufacturer Vendor designation GE designation

Motor

Annex to A -Design Ass essment No. 44 220 14555130a-DA-GL, Rev. 2

GE Energy cast part EN-GJS-40 0-18U-L T 103W3140

GE Energy welded part S355J2, ASTM A572 Grade 50 115W7655 (fabrication) 115W7656 (machining)

GE Energy Ball bearing slewing ring 115W7485

GE Energy Ball bearing slewing ring 103W4701

Nanjing High Speed Gear Manufacturer Co., Ltd 4-stage planetary gearbox FDX207G-0 1-00R1 (60Hz) FDX207G-01- 00R15 (50Hz) 108W4725P001 (60Hz) 108W5441P001 (50Hz) AKWJ132M1-6B (Suzhou Lego Motors - 60Hz) AKWJ132M1-6A (Suzhou Lego Motors - 50Hz)

Liebherr Components Biberach GmbH 4-stage planetary gearbox DAT 500/2400 (60 Hz) DAT 500/2401 (50 Hz) 108W4726P001 (60 Hz) 108W5442P001 (50 Hz) KGF 588/6 JWE ( Liebherr - 60 Hz) KGF 588/6 IP 54 ( Liebherr - 50 Hz)

Bonfiglio li Trasmital 714T4W 108W8434P001 (60 Hz) 108W8435P001 (50 Hz) BN 132MA6 400/690-60 (Bonfigl ioli - 60 Hz) BN 132MA6 400/690-50 (Bonf igl ioli - 50 Hz)

Friction system assembly (Yaw Brake)

Top Box 60 Hz

Top Box 50 Hz

Generator 60Hz

alternative (only 60 Hz) Manufacturer Vendor designati on GE designat ion Motor

Design Type GE drawing No.

alternative: Design Type GE drawing No.

Design Type

GE designation

Design Type

GE designation

Manufacturer Vendor designation GE gener ic designati on Rated Power Rated voltage Rated speed Isolation class Degree of protection

alternative Manufacturer Vendor designation GE generic designation Rated Power Rated voltage Rated speed Isolat ion class Degree of protection

Annex to A-Design Assessm ent No. 44 220 14555130a -DA-GL, Rev. 2

Nabtesco Corporation RGS100B 108W8523 P00 1 AMBY 132S/A6 - MY/A6A -C3098 (Lafert)

GE Energy Mechanica l w ith spring washe r 115W6389

GE Energy Mechanical with spr ing washe r 115W7433

GE Energy 151X1230 TA0 1SA04 107W5345POO 1 108W5039 109W3211 109W4024

GE Energy 151X1230TA01SA03 / 107W5345 P004 151X1230TA01SA04 / 107W5345 P006 107W5345P08 108W5039 108W3211 109W4024

Hitachi TFFOAN-DQ/H IG-3669KOO 109W3459P001 1790 kW 690 V 1465 rpm F IP54

GE Vietnam TFFOAN-DQ /HIG-3669KOOVN-GE 109W3458 POO 1 1790 kW 690V 1465 rpm F IP54

Page 10 f j.

Generator 50Hz

Down Tower Assembly (con verter , main cabinet, power distribution panel)

Power Cable Assembly

Control Cable Assembly

Bus Bar

Tower (hh 79.7 m)

Manufactu rer Vendor des ignation GE gener ic designation Rated Power Rated voltage Rated speed Isolation class Degree of protection

alternative Manufacturer Vendo r designation GE generic designation Rated Power Rated voltage Rated speed Isolation class Degree of protection

Manufacturer Vendo r designation GE designa tion

Design GE designation

Design GE designation

Design GE designation

Design Length GE Drawing No.

Ann ex to A-Design Assessment No. 44 220 14555130a-DA-GL, Rev. 2

NTC DASAA 5024-4UAB CF028 109W1663P001 1790 kW 690 V 1831 rpm F IP54

Wine rgy JFEE-500SR-04A 109W1665P001 1790 kW 690V 1831 rpm F IP54

GE Salem 151X 1230KA02SA03 107W5379P007

GE Energy 115W7778 (60Hz) 120W0065 (50Hz)

GE Energy 120W0081 (60 Hz) 104W8103 / 120W0099 (50 Hz)

GE Energy 115W7874G001 / 200W0216G001 (60 Hz) 115W787 4G002 ( 50 Hz)

Tubular steel tower with 3 sections 77.3 m 123W1996 (STW-Version) 123W1997 (STW-Version) 123W 1998 (STW-Version) 114W6950 (STW-Ve rsion) 123W 1999 (STW-Version) 123W2036 (CWE-Version) 123W2037 (CWE-Version) 123W2038 (CWE-Vers ion) 200W0074 (CWE-Vers ion) 123W2039 (CWE-Version)

Page 11 v;JJ-

Control and safety system Manufacturer

Type GE Energy Mark Vie

Note: Please refer to the appropriate certification reports for revision control of drawi ngs and related design documents .

End of Annex

Essen, 201" Apr il 2015

Langemarcks tral1e 20 • 45141 Essen • email : windenergy@tuev-nord.de

Ann ex to A -Des ign Assessm ent No . 44 220 14555130 a-DA-GL, Rev . 2

Page 12 of 12