standard aluminum products inc. section a index doors
TRANSCRIPT
STANDARD ALUMINUM PRODUCTS INC.
Section A IndexDoors / Entrance
175 Series Narrow Stile Door Specifications A1
175 Series Narrow Stile Door Profiles A2 - A3
275 Series Institutional Door Specifications A5
275 Series Institutional Door Profiles A6 - A7
350 Series Medium Stile Door Specifications A9
A10 - A11350 Series Medium Stile Door Profiles
500 Series Wide Stile Door Specifications A13
A14 - A15500 Series Wide Stile Door Profiles
200T Series Thermally Broken Door Specifications A22
A23 - A24200T Series Thermally Broken Door Profiles
500T Series Thermally Broken Door Specifications A26
A27 - A28500T Series Thermally Broken Door Profiles
Standard Thresholds A17
Hardware Locations / Door Swings A20 - A21
SD1750 Series Sliding Door Specifications A31
SD1750 Series Sliding Door Profiles A32 - A49
SD2000 Series Top Hung Sliding Door Specifications A53
SD2000 Series Top Hung Sliding Door Profiles A54 - A61
BF2000 Series Bi-Folding Door Specifications A63
BF2000 Series Bi-Folding Door Profiles A64 - A66
SD1750 Sliding Door Hardware A50 - A51
A29 - A30Thermally Broken Door Mid Panel / Thresholds
BF2000 Series Bi-Folding Door Pivot Layout A67 - A68
Concealed Closer Option A16
Mid-Panels A18 - A19
STANDARD ALUMINUM PRODUCTS INC.
Specification175 Narrow Stile Door
A-1
Design
Door Thickness 1.75”
Stile Width 2.00”
Top Rail Height 3.125”
Bottom Rail Height 3.125”
Glass stops available;
1. Bevelled Single Glazing
2. Square Single Glazing
3. Sealed Unit Glazing
Hardware
Hardware for aluminum doors and
door frames shall be the
manufacturer's standard.
Hardware for doors shall be;
1. Pivoting hinges
· Offset pivots
· Continuous Gear hinges
· Butt hinges
2. Lock type
3. Closer
4. Exit Device
5. Push/pull handles
6. Threshold
7. Miscellaneous
Standard Aluminum uses hardware
designed and engineered for
aluminum entrance doors by
recognized hardware manufactures
such as Adams Rite, and Dorma
Door Controls. Door weather strip
shall be supplied by the door
manufacturer. If custom hardware is
to be furnished by others, templates
and physical hardware must be
submitted prior to any fabrication.
Special Features
All doors have snap in glass setting
blocks for either single or double
glass. M.S. hook lock b.s. is 1.125
inches to give maximum clearance
from door framing material. All
horizontal sections are extruded
0.03 narrower than vertical sections
to assure not only an accurate fit but
a clean joint, free of unsightly saw
cut lines.
Optional Accessories
In addition to standard push/pull type
hardware Standard Aluminum offers
a line of;
1. Custom handles
2. Mid panels
3. Muntin bars
4. Panic sets
5. Offset pivots, spring loaded
type, round in appearance
and easy to adjust.
6. Continuous gear hinges
7. Roller bearing butt hinges
8. 5 ½” bottom rail
9. 6 ½” bottom rail
10. 10” bottom rail
General Description
Work included; The glazing
contractor shall furnish all necessary
materials, labour and equipment for
the complete installation of aluminum
entrance doors, door frames and
hardware as detailed on the
drawings and specified herein.
Work not included; Structural
support for the framing system,
wood framing, structural steel,
masonry and final cleaning.
Construction
All corners shall be mechanically
fastened using plated 3/8 threaded
rods secured into an extruded race in
the rail section; all fasteners used
shall be plated. Corner construction
shall remain flexible and not break or
tear when a full size 3'0” x 7'0” door
is over stressed in a direction normal
to the plane of the doors, as when
the doors is slammed against a floor
mounted stop or immovable object.
All doors and components are either
manufactured or assembled by our
trained and experienced technicians.
Material
All extruded aluminum shall be 6063
alloy with a minimum T-5 temper. The
thickness of the section varies from
0.150 at web section to .0110 on
non-bearing wall surfaces. Glazing
gaskets shall be EPDM elastomeric
extrusions.
Finish
Both anodized and painted finishes are
available. All integral colour anodizing
is Architectural Class II., 0.4 to 0.7 mm
coating. A fluropolymer paint coating
conforming to the requirements of
AAMA 2603 and AAMA 2605
specifications, the toughest coating in
the industry standards.
Testing
All testing shall be on full size door and
frame sections. Air infiltration shall be
tested in accordance with
ASTM-Designation E283-91 or
ASHRAE standards #90-80. Single
doors shall not exceed .50 CFM per
lin.ft. of perimeter. Pairs of doors shall
not exceed 1.0 CFM per lin.ft. of
perimeter.
Protection and Cleaning
After installation the general contractor
should adequately protect the exposed
aluminum and glass surfaces from
damage by other trades. i.e.(but not
restricted to) cement splash and leach,
grinding, polishing compounds, plaster,
paint, lime, acids and other
contaminants.
STANDARD ALUMINUM PRODUCTS INC.
175 Narrow Stile Door
Elevation
1 3/4"
45mm
3 1
/8
"
80
mm
3 1
/8
"
80
mm
45mm
1 3/4"
45mm
1 3/4"
6 1
/2
"
16
5m
m
Bottom Rail
(Standard)
Bottom Rail
(Optional) (Optional)
Bottom Rail
1 3/4"
10
"
45mm
25
4m
m
Top Rail
Double Glazed S/U
(Optional)
A-2SCALE 1/2 FULL SIZE
STANDARD ALUMINUM PRODUCTS INC.
175 Narrow Stile Door
2 1/16"
52mm
1 3
/4
"
45
mm
Single Acting Stiles
1 3
/4
"
45
mm
2"
51mm
Double Acting Stiles
1 3
/4
"
45
mm
Meeting Stiles
2 1/8"
54mm
Double Glazed S/U
(Optional)
A-3SCALE 1/2 FULL SIZE
STANDARD ALUMINUM PRODUCTS INC.
A-4
275 Institutional DoorSTANDARD ALUMINUM PRODUCTS INC.
Specifications
A-5
Design
Door Thickness 1.875”
Stile Width 2.75”
Top Rail Height 3.125”
Bottom Rail Height 6.50”
Glass stops available;
1. Bevelled Single Glazing
2. Square Single Glazing
3. Sealed Unit Glazing
Door panels are supplied with
continuous gear hinges.
Hardware
Hardware for aluminum doors and door
frames shall be the manufacturer's
standard.
Hardware for doors shall be;
1. Continuous gear hinges
2. Lock type
3. Closer
4. Exit Device
5. Push/pull handles
6. Threshold
7. Miscellaneous
Standard Aluminum uses hardware
designed and engineered for aluminum
entrance doors by recognized hardware
manufactures such as Adams Rite, and
Dorma Door Controls. Door weather
strip shall be supplied by the door
manufacturer. If custom hardware is to
be furnished by others, templates and
physical hardware must be submitted
prior to any fabrication.
Special Features
All doors have snap in glass setting
blocks for either single or double glass.
M.S. hook lock b.s. is 1.125 inches to
give maximum clearance
from door framing material. All
horizontal sections are extruded 0.03
narrower than vertical sections to
assure not only an accurate fit but a
clean joint, free of unsightly saw cut
lines.
Optional Accessories
In addition to standard push/pull type
hardware Standard Aluminum offers a
line of;
1. Custom handles
2. Mid panels
3. Muntin bars
4. Panic sets
5. 10” bottom rail
General Description
Work included; The glazing contractor
shall furnish all necessary materials,
labour and equipment for the complete
installation of aluminum entrance doors,
door frames and hardware as detailed
on the drawings and specified herein.
Work not included; Structural support
for the framing system, wood framing,
structural steel, masonry and final
cleaning.
Construction
All corners shall be mechanically
fastened using plated 3/8" threaded
rods secured into an extruded race in
the rail section; all fasteners used shall
be plated. Corner construction shall
remain flexible and not break or tear
when a full size 3'0” x 7'0” door is over
stressed in a direction normal to the
plane of the doors, as when the doors is
slammed against a floor mounted stop
or immovable object. All doors and
components are either manufactured or
assembled by our trained and
experienced technicians.
Material
All extruded aluminum shall be 6063
alloy with a minimum T-5 temper. The
thickness of the section varies from
0.150 at web section to .0110 on
non-bearing wall surfaces. Glazing
gaskets shall be EPDM elastomeric
extrusions.
Finish
Both anodized and painted finishes are
available. All integral colour anodizing is
Architectural Class II., 0.4 to 0.7 mm
coating. A fluropolymer paint coating
conforming to the requirements of
AAMA 2603 and AAMA 2605
specifications, the toughest coating in
the industry standards.
Testing
All testing shall be on full size door and
frame sections. Air infiltration shall be
tested in accordance with
ASTM-Designation E283-91 or
ASHRAE standards #90-80. Single
doors shall not exceed .50 CFM per
lin.ft. of perimeter. Pairs of doors shall
not exceed 1.0 CFM per lin.ft. of
perimeter.
Protection and Cleaning
After installation the general contractor
should adequately protect the exposed
aluminum and glass surfaces from
damage by other trades. i.e.(but not
restricted to) cement splash and leach,
grinding, polishing compounds, plaster,
paint, lime, acids and other
contaminants.
16
5m
m
6 1
/2
"
1 7/8"
48mm
80
mm
STANDARD ALUMINUM PRODUCTS INC.
3 1
/8
"
Elevation
Top Rail
275 Institutional Door
48mm
1 7/8"
(Standard)
Bottom Rail
1 3/4"
45mm
10
"
25
4m
m
Double Glazed S/U
(Optional)
Bottom Rail
(Optional)
A-6SCALE 1/2 FULL SIZE
1 7
/8
"
Meeting Stiles
2 3/4"
48
mm
1 7
/8
"
70mm
2 3/4"
Double Acting Stiles
48
mm
Single Acting Stiles
STANDARD ALUMINUM PRODUCTS INC.
275 Institutional Door
70mm 70mm
2 3/4"
2 3/4"
1 7
/8
"
48
mm
70mm
2 3/4"
70mm
Double Glazed S/U
(Optional)
SCALE 1/2 FULL SIZE
A-7
STANDARD ALUMINUM PRODUCTS INC.
A-8
350 Medium Stile DoorSTANDARD ALUMINUM PRODUCTS INC.
Specifications
A-9
Design
Door Thickness 1.75”
Stile Width 3.50”
Top Rail Height 3.125”
Bottom Rail Height 6.5”
Glass stops available;
1. Bevelled Single Glazing
2. Square Single Glazing
3. Sealed Unit Glazing
Hardware
Hardware for aluminum doors and door
frames shall be the manufacturer's
standard.
Hardware for doors shall be;
1. Pivoting hinges
· Offset pivots
· Continuous Gear hinges
· Butt hinges
2. Lock type
3. Closer
4. Exit Device
5. Push/pull handles
6. Threshold
7. Miscellaneous
Standard Aluminum uses hardware
designed and engineered for aluminum
entrance doors by recognized hardware
manufactures such as Adams Rite, and
Dorma Door Controls. Door weather
strip shall be supplied by the door
manufacturer. If custom hardware is to
be furnished by others, templates and
physical hardware must be submitted
prior to any fabrication.
Special Features
All doors have snap in glass setting
blocks for either single or double glass.
M.S. hook lock b.s. is 1.125 inches to
give maximum clearance
from door framing material. All
horizontal sections are extruded 0.03
narrower than vertical sections to
assure not only an accurate fit but a
clean joint, free of unsightly saw cut
lines.
Optional Accessories
In addition to standard push/pull type
hardware Standard Aluminum offers a
line of;
1. Custom handles
2. Mid panels
3. Muntin bars
4. Panic sets
5. Offset pivots, spring loaded
type, round in appearance and
easy to adjust.
6. Continuous gear hinges
7. Roller bearing butt hinges
8. 10” bottom rail
General Description
Work included; the glazing contractor
shall furnish all necessary materials,
labour and equipment for the complete
installation of aluminum entrance doors,
door frames and hardware as detailed
on the drawings and specified herein.
Work not included; Structural support
for the framing system, wood framing,
structural steel, masonry and final
cleaning.
Construction
All corners shall be mechanically
fastened using plated 3/8" threaded
rods secured into an extruded race in
the rail section; all fasteners used shall
be plated. Corner construction shall
remain flexible and not break or tear
when a full size 3'0” x 7'0” door is over
stressed in a direction normal to the
plane of the doors, as when the doors is
slammed against a floor mounted stop
or immovable object. All doors and
components are either manufactured or
assembled by our trained and
experienced technicians.
Material
All extruded aluminum shall be 6063
alloy with a minimum T-5 temper. The
thickness of the section varies from
0.150 at web section to .0110 on
non-bearing wall surfaces. Glazing
gaskets shall be EPDM elastomeric
extrusions.
Finish
Both anodized and painted finishes are
available. All integral colour anodizing is
Architectural Class II., 0.4 to 0.7 mm
coating. A fluropolymer paint coating
conforming to the requirements of
AAMA 2603 and AAMA 2605
specifications, the toughest coating in
the industry standards.
Testing
All testing shall be on full size door and
frame sections. Air infiltration shall be
tested in accordance with
ASTM-Designation E283-91 or
ASHRAE standards #90-80. Single
doors shall not exceed .50 CFM per
lin.ft. of perimeter. Pairs of doors shall
not exceed 1.0 CFM per lin.ft. of
perimeter.
Protection and Cleaning
After installation the general contractor
should adequately protect the exposed
aluminum and glass surfaces from
damage by other trades. i.e.(but not
restricted to) cement splash and leach,
grinding, polishing compounds, plaster,
paint, lime, acids and other
contaminants.
6 1
/2
"
16
5m
m
1 3/4"
45mm
Bottom Rail
(Standard)
Bottom Rail
(Optional)
STANDARD ALUMINUM PRODUCTS INC.
80
mm
3 1
/8
"
Elevation
Top Rail
350 Medium Stile Door
45mm
1 3/4"
1 3/4"
45mm
10
"
25
4m
m
Double Glazed S/U
(Optional)
A-10SCALE 1/2 FULL SIZE
45
mm
1 3
/4
"
3 5/8"
Meeting Stiles
92mm
3 1/2"
90mm
3 1/2"
1 3
/4
"
45
mm
Double Acting Stiles
Single Acting Stiles
STANDARD ALUMINUM PRODUCTS INC.
1 3
/4
"
45
mm
3 9/16"
3 1/2"
91mm
90mm 90mm
3 1/2"
90mm
350 Medium Stile Door
Double Glazed S/U
(Optional)
SCALE 1/2 FULL SIZE
A-11
STANDARD ALUMINUM PRODUCTS INC.
A-12
500 Wide Stile DoorSTANDARD ALUMINUM PRODUCTS INC.
Specifications
A-13
Finish
Both anodized and painted finishes are
available. All integral colour anodizing is
Architectural Class II., 0.4 to 0.7 mm
coating. A fluropolymer paint coating
conforming to the requirements of
AAMA 603 and AAMA 605
specifications, the toughest coating in
the industry standards.
Testing
All testing shall be on full size door and
frame sections. Air infiltration shall be
tested in accordance with
ASTM-Designation E283-91 or
ASHRAE standards #90-80. Single
doors shall not exceed .50 CFM per
lin.ft. of perimeter. Pairs of doors shall
not exceed 1.0 CFM per lin.ft. of
perimeter.
Protection and Cleaning
After installation the general contractor
should adequately protect the exposed
aluminum and glass surfaces from
damage by other trades. i.e.(but not
restricted to) cement splash and leach,
grinding, polishing compounds, plaster,
paint, lime, acids and other
contaminants.
Optional Accessories
In addition to standard push/pull type
hardware Standard Aluminum offers a
line of;
1. Custom handles
2. Mid panels
3. Muntin bars
4. Panic sets
5. Offset pivots, spring loaded
type, round in appearance and
easy to adjust.
6. Continuous gear hinges
7. Roller bearing butt hinges
8. 10” bottom rail
General Description
Work included; The glazing contractor
shall furnish all necessary materials,
labour and equipment for the complete
installation of aluminum entrance doors,
door frames and hardware as detailed
on the drawings and specified herein.
Work not included; Structural support
for the framing system, wood framing,
structural steel, masonry and final
cleaning.
Construction
All corners shall be mechanically
fastened using plated 3/8" threaded
rods secured into an extruded race in
the rail section; all fasteners used shall
be plated. Corner construction shall
remain flexible and not break or tear
when a full size 3'0” x 7'0” door is over
stressed in a direction normal to the
plane of the doors, as when the doors is
slammed against a floor mounted stop
or immovable object. All doors and
components are either manufactured or
assembled by our trained and
experienced technicians.
Material
All extruded aluminum shall be 6063
alloy with a minimum T-5 temper. The
thickness of the section varies from
0.150 at web section to .0110 on
non-bearing wall surfaces. Glazing
gaskets shall be EPDM elastomeric
extrusions.
Design
Door Thickness 1.75”
Stile Width 5.00”
Top Rail Height 5.50”
Bottom Rail Height 6.50”
Glass stops available;
1. Bevelled Single Glazing
2. Square Single Glazing
3. Sealed Unit Glazing
Hardware
Hardware for aluminum doors and door
frames shall be the manufacturer's
standard.
Hardware for doors shall be;
1. Pivoting hinges
· Offset pivots
· Continuous Gear hinges
· Butt hinges
2. Lock type
3. Closer
4. Exit Device
5. Push/pull handles
6. Threshold
7. Miscellaneous
Standard Aluminum uses hardware
designed and engineered for aluminum
entrance doors by recognized hardware
manufactures such as Adams Rite, and
Dorma Door Controls. Door weather
strip shall be supplied by the door
manufacturer. If custom hardware is to
be furnished by others, templates and
physical hardware must be submitted
prior to any fabrication.
Special Features
All doors have snap in glass setting
blocks for either single or double glass.
M.S. hook lock b.s. is 1.125 inches to
give maximum clearance
from door framing material. All
horizontal sections are extruded 0.03
narrower than vertical sections to
assure not only an accurate fit but a
clean joint, free of unsightly saw cut
lines.
Elevation
(Optional)
(Standard)
16
5m
m
6 1
/2
"
Bottom Rail
1 3/4"
45mm
Bottom Rail
STANDARD ALUMINUM PRODUCTS INC.
500 Wide Stile Door
5 1
/2
"
Top Rail
(Standard)
1 3/4"
45mm
14
0m
m
1 3/4"
45mm
10
"
25
4m
m
Double Glazed S/U
(Optional)
A-14SCALE 1/2 FULL SIZE
5"5"
5 1/8"
45
mm
1 3
/4
"
1 3
/4
"
45
mm
127mm
5"
Meeting Stiles
Double Acting Stiles
5"5 1/16"
STANDARD ALUMINUM PRODUCTS INC.1
3
/4
"
45
mm
129mm
Single Acting Stiles
127mm
127mm
130mm
500 Wide Stile Door
Double Glazed S/U
(Optional)
SCALE 1/2 FULL SIZE
A-15
127mm
STANDARD ALUMINUM PRODUCTS INC.
Top Rail
Concealed Closer Option
A-16SCALE 1/2 FULL SIZE
(Standard)
Bottom Rail(Standard)
1/8"
3mm
13
/4
"
45
mm
Top Rail(With Optional S/U)
Bottom Rail(With Optional S/U)
13
/4
"
45
mm
OverheadConcealed Closer
Offset Concealed Center Hung
Shown With 175 Series Doors
ThresholdsSTANDARD ALUMINUM PRODUCTS INC.
4"
4"
6" 6 1/8"
8"
SKID PROOF - All Thresholds may be
coated with ULTRA-grip
an abrasive coating of
stainless-steel particles
designed for skid
resistance and superior
ADAAG-1992, CABO ASTM E 90-90
than 1:2. Meets requirements of
with slope portions not greater
no more than 1/4" vertical rise
are 1/2" high, or less, and have
Product displaying this symbolHANDICAPPED -
durability in high traffic areas.
ASTM E 1408-90. All products meet
or exceed ADA requirements.
STANDARD APPLICATION
A-17SCALE 1/2 FULL SIZE
1/2
"
6 1/8"
1/4
"1
/4
"1
/2
"
1/2
"
1/2
"
203mm
156mm
152mm 156mm
102mm
102mm
* PLEASE ENQUIRE FOR ADDITIONAL OPTIONS *
Mid PanelsSTANDARD ALUMINUM PRODUCTS INC.
5/8"
16mm
5/8" Muntin
3 1
/8
"
79
mm
3 1/8" Mid Panel
10
"
25
4m
m
10" Mid Panel
6 5
/1
6"
16
0m
m
6 5/16" Mid Panel
S/G STOPS: 5/8" (16mm)
S/U STOPS: 3/4" (19mm)
A-18SCALE 1/2 FULL SIZE
A-19
STANDARD ALUMINUM PRODUCTS INC.
Mid Panels
2" Narrow Stiles
44
" S
td
. H
eig
ht
6 1/2"
10"
42
" S
td
. H
eig
ht
3 1/8"
6 5/16"
3 1/8" Top Rail
6 5/16" Mid-Panel
3 1/8" Bottom Rail
2" Narrow Stiles
3 1/8" Top Rail
10" Mid-Panel
6 1/2" Bottom Rail
.625 Muntin can be used as a
single muntin or as many as the
design requires to achieve the
design appearance
STANDARD ALUMINUM PRODUCTS INC.
Hardware Locations
4 1/2" X 4"
Butt Hinge
A-20
36
"
43
"
46
1
/2
"
54
"
42
"
6 7/8"
9 5/16"
EQ
.E
Q.
49
"
38
1
/2
"
Locations
Intermediate
Pivot Location
Cylinder & M.S. Lock
Pull Handle
Push Bar
M.S. Lock (High Position)
Center Of Panic
Adams Rite
8600 Concealed Panic
8800 Rim Panic
10" Or 12"
Back To Back
T/O Cut
38
1
/2
"
48
1
/2
"
Offset Handle
(With 1" Dia. Pushbar)
Offset Handles
STANDARD ALUMINUM PRODUCTS INC.
Door Swings
A-21
Left Hand In Left Hand Out Right Hand InRight Hand Out
As Viewed From Outside
36"
914mm
72"
1829mm
Standard Opening For
Single Door
Standard Opening For
Double Doors
84
"
2134m
m
Standard Height
Stile Width 2.75"
200T Narrow Stile Thermally Broken DoorSTANDARD ALUMINUM PRODUCTS INC.
Specifications
A-22
HARDWARE
Hardware for aluminum doors
and door frames shall be the
entrance manufacturer's
standard:
1. Continuous Gear Hinges
2. Lock Type
3. Closer
4. Exit Device
5. B/B Offset Handle
6. Threshold
7. Miscellaneous
Standard Aluminum uses
hardware designed and
engineered for aluminum
entrance doors by recognized
hardware manufacturers such as
Adams Rite and Dorma Door
Controls. Weatherstrip for the
door is supplied by the door
manufacturer. If custom hardware
is to be furnished by others,
templates and physical hardware
must be submitted prior to any
fabrication.
CONSTRUCTION
All corners shall be mechanically
fastened using
plated 3/8 threaded rods secured
into an extruded race in the rail
section; all fasteners used shall
be plated. Corners construction
shall remain flexible and not
break or tear when a full
size (3'-0” x 7'-0”) door is over
stressed in a direction normal to
the plane of the doors, as when
the door is slammed against a
floor mounted stop or immovable
object. All doors and
components are either
manufactured or assembled by
our trained and experienced
technicians.
Glass stops available:
1. Sealed unit glazing
Door Panels are supplied with
continuous gear hinges.
GENERAL DESCRIPTION
Work Included: The glazing
contractor shall furnish all
necessary materials, labour and
equipment for the complete
installation of aluminum entrance
doors, door frames and hardware
as detailed on the drawings and
specified herein.
Work Not Included: Structural
support of the framing system,
wood framing, structural steel,
masonry and final cleaning.
MATERIAL
All extruded aluminum shall be
6063 alloy with a minimum T-5
temper. The thickness of the
section varies from 0.110 at web
section to .0160 on non-bearing
wall surfaces. Glazing gaskets
shall be EPDM elastomeric
extrusions.
FINISH
Both anodized and painted
sections are available. All
intergral colour anodizing is
Architectural Class II., 0.4 to 0.7
mil. coating. A fluoropolymer
paint coating conforming to the
requirements of AAMA 2603 and
AAMA 2605 specifications, the
toughest coating in the industry
standards.
TESTING
All testing shall be on full size
door and frame sections. Air
infiltration shall be tested in
accordance with
ASTM-Designation E283-91 or
ASHRAE standard #90-80.
Single doors shall not exceed .50
CFM per lin.ft. of perimeter. Pairs
of doors shall not exceed 1.0
CFM per lin.ft of perimeter.
SPECIAL FEATURES
All doors have snap in glass
setting blocks for double glass.
M.S. hook lock backset is 1.5
inches to give maximum
clearance from door framing
material.
OPTIONAL ACCESSORIES
In addition to standard push/pull
type hardware Standard
Aluminum
Offers a line of;
1. Custom handles
2. Mid panels
3. Panic sets manufactured by
Adams Rite
4. Butt hinges
5. 6 1/2" Bottom Rail
PROTECTION AND CLEANING
After installation the general
contractor should adequately
protect the exposed aluminum
and glass surfaces from damage
by others trades. i.e. (but not
restricted to) cement splash and
leach, grinding, polishing
compounds, plaster, paint, lime,
acids and other contaminants.
Door Thickness 2.00”
Top Rail Height
Bottom Rail Height
3.25"
3.25"
Elevation
STANDARD ALUMINUM PRODUCTS INC.
200T Narrow Stile Thermally Broken Door
A-23SCALE 1/2 FULL SIZE
3 1
/4
"
(Optional)
Bottom Rail
2"
51mm
6 1
/2
"
16
5m
m
83
mm
Top Rail
(Standard)
3 1
/4
"
83
mm
Bottom Rail
(Standard)
2"
51mm
2 3/4"
70mm
5 5/8"
143mm
Meeting Stiles
Single Acting Stiles
2 3/4"
70mm
1
8
"
3mm
STANDARD ALUMINUM PRODUCTS INC.
A-24SCALE 1/2 FULL SIZE
200T Narrow Stile Thermally Broken Door
STANDARD ALUMINUM PRODUCTS INC.
A-25
500T Wide Stile Thermally Broken DoorSTANDARD ALUMINUM PRODUCTS INC.
Specifications
A-26
HARDWARE
Hardware for aluminum doors
and door frames shall be the
entrance manufacturer's
standard:
1. Continuous Gear Hinges
2. Lock Type
3. Closer
4. Exit Device
5. B/B offset handle
6. Threshold
7. Miscellaneous
Standard Aluminum uses
hardware designed and
engineered for aluminum
entrance doors by recognized
hardware manufacturers such as
Adams Rite and Dorma Door
Controls. Weatherstrip for the
door is supplied by the door
manufacturer. If custom hardware
is to be furnished by others,
templates and physical hardware
must be submitted prior to any
fabrication.
CONSTRUCTION
All corners shall be mechanically
fastened using
plated 3/8 threaded rods secured
into an extruded race in the rail
section; all fasteners used shall
be plated. Corners construction
shall remain flexible and not
break or tear when a full
size (3'-0” x 7'-0”) door is over
stressed in a direction normal to
the plane of the doors, as when
the door is slammed against a
floor mounted stop or immovable
object. All doors and
components are either
manufactured or assembled by
our trained and experienced
technicians.
Glass stops available:
1. Sealed unit glazing
Door Panels are supplied with
continuous gear hinges.
GENERAL DESCRIPTION
Work Included: The glazing
contractor shall furnish all
necessary materials, labour and
equipment for the complete
installation of aluminum entrance
doors, door frames and hardware
as detailed on the drawings and
specified herein.
Work Not Included: Structural
support of the framing system,
wood framing, structural steel,
masonry and final cleaning.
MATERIAL
All extruded aluminum shall be
6063 alloy with a minimum T-5
temper. The thickness of the
section varies from 0.110 at web
section to .0160 on non-bearing
wall surfaces. Glazing gaskets
shall be EPDM elastomeric
extrusions.
FINISH
Both anodized and painted
sections are available. All
intergral colour anodizing is
Architectural Class II., 0.4 to 0.7
mil. coating. A fluoropolymer
paint coating conforming to the
requirements of AAMA 2603 and
AAMA 2605 specifications, the
toughest coating in the industry
standards.
TESTING
All testing shall be on full size
door and frame sections. Air
infiltration shall be tested in
accordance with
ASTM-Designation E283-91 or
ASHRAE standard #90-80.
Single doors shall not exceed .50
CFM per lin.ft. of perimeter. Pairs
of doors shall not exceed 1.0
CFM per lin.ft of perimeter.
SPECIAL FEATURES
All doors have snap in glass
setting blocks for double glass.
M.S. hook lock backset is 1.5
inches to give maximum
clearance from door framing
material.
OPTIONAL ACCESSORIES
In addition to standard push/pull
type hardware Standard
Aluminum
Offers a line of;
1. Custom handles
2. Mid panels
3. Panic sets manufactured by
Adams Rite
4. Butt hinges
PROTECTION AND CLEANING
After installation the general
contractor should adequately
protect the exposed aluminum
and glass surfaces from damage
by others trades. i.e. (but not
restricted to) cement splash and
leach, grinding, polishing
compounds, plaster, paint, lime,
acids and other contaminants.
Door Thickness 2.00”
Stile Width 5.00”
Top Rail Height
Bottom Rail Height
6.50"
6.50"
Elevation
STANDARD ALUMINUM PRODUCTS INC.
500T Wide Stile Thermally Broken Door
A-27SCALE 1/2 FULL SIZE
(Standard)
Bottom Rail
2"
51mm
6 1
/2
"
16
5m
m
Top Rail
(Standard)
6 1
/2
"
16
5m
m
STANDARD ALUMINUM PRODUCTS INC.
SCALE 1/2 FULL SIZE
A-28
5"
127mm
10 1/8"
257mm
Meeting Stiles
Single Acting Stiles
500T Wide Stile Thermally Broken Door
5"
127mm
1
8
"
3mm
STANDARD ALUMINUM PRODUCTS INC.
SCALE 1/2 FULL SIZE
A-29
Mid Rail
2"
51mm
6 1
/2
"
16
5m
m
3 1
/4
"
83
mm
Mid Rail
2"
51mm
Thermally Broken Door Mid Panels
4"
10
2m
m
7 1
/4
"
18
4m
m
ThresholdsSTANDARD ALUMINUM PRODUCTS INC.
SKID PROOF - All Thresholds may be
coated with ULTRA-grip
an abrasive coating of
stainless-steel particles
designed for skid
resistance and superior
durability in high traffic areas.
A-30SCALE 1/2 FULL SIZE
6 1/8"
1"
1/2
"
156mm
6 1/8"
STANDARD APPLICATION
1/2
"
6 1/8"
1/2
"
156mm
156mm
SD1750 Mall SliderSTANDARD ALUMINUM PRODUCTS INC.
Specifications
A-31
HARDWARE
Hardware for aluminum doors and
door frames shall be the entrance
manufacturer's standard:
1. M.S. hook bolt
2. Cylinder
3. Thumbturn
4. Flush finger pulls
5. Tandem Rollers
6. Roller Handles
The locking jamb with the lock cutout
is furnished loose. If custom hardware
is to be furnished by others,
templates and physical hardware
must be submitted prior to any
fabrication.
CONSTRUCTION
Standard Aluminum's SD1750 Series
multi track sliding front offers
unrestricted design options for easy
traffic flow. Multi track units with
parallel stacking for a variety of
interior applications. Moveable panels
can be stacked inline behind a wall, a
fixed end panel or an adjacent pocket.
The floor track may be either
recessed or surface applied. Each
sliding door panel has two tandem
steel rollers to provide easy operation
and longevity. All doors and
components are either manufactured
or assembled by our trained and
experienced technicians.
PERFORMANCE REQUIREMENTS
Ideally suited for show rooms,
shopping malls and office buildings.
The SD1750 has been used in
high-end residential applications
where a more substantial sliding door
is required. For this application
additional weather stripping is applied
to the sill. he SD1750 is generally
assembled with the sliding panel to
the inside but can be made with the
sliding panel to the outside with
additional sill weathering when
required.
Glass stops available:
1. Square single glazing
2. Sealed unit glazing
GENERAL DESCRIPTION
Work Included: The glazing
contractor shall furnish all
necessary materials, labour and
equipment for the complete
installation of aluminum entrance
doors, door frames and hardware
as detailed on the drawings and
specified herein.
Work Not Included: Structural
support of the framing system,
wood framing, structural steel,
masonry and final cleaning.
MATERIAL
All extruded aluminum shall be
6063 alloy with a minimum T-5
temper. The thickness of the
section varies from 0.150 at web
section to .0110 on non-bearing
wall surfaces. Glazing gaskets
shall be EPDM elastomeric
extrusions.
FINISH
Both anodized and painted
sections are available. All
intergral colour anodizing is
Architectural Class II., 0.4 to 0.7
mil. coating. A fluoropolymer
paint coating conforming to the
requirements of AAMA 603 and
AAMA 605 specifications, the
toughest coating in the industry
standards.
Door panels are constructed from
6063-T5 alloy while the base
track is extruded from 6061-T6
alloy and hard coat clear
anodized to extend wear and
reduces friction from the tandem
rollers
OPTIONAL ACCESSORIES
Many options are available to the
designer such as:
1. Egress Door
2. Muntins and Panels
3. Higher Base Rail
PROTECTION AND CLEANING
After installation the general
contractor should adequately
protect the exposed aluminum
and glass surfaces from damage
by others trades. i.e. (but not
restricted to) cement splash and
leach, grinding, polishing
compounds, plaster, paint, lime,
acids and other contaminants.
Top Rail Height 3.125”
Bottom Rail Height 3.125”
Stile Width 2.00”
Door Thickness 1.75”
Top Track/Jamb 1.625”
Sill Track 0.437”
STANDARD ALUMINUM PRODUCTS INC.
2
1
2
FIN
IS
HE
D O
PE
NIN
G
1 5
/8
"
SURFACE MOUNTEDTRACK
1
4 1/2"
OX
ANY NUMBER OF PANELS
MOUNTING
SHOE
A-32SCALE 1/2 FULL SIZE
Multi Sliders ProfileSD 1750 Mall Sliders
7/8
"
3
16
"
SD 1750 Mall SlidersSTANDARD ALUMINUM PRODUCTS INC.
Multi Sliders Profile
OX
3 4 5
FIXED JAMB
LOCKING JAMB
3 4 5
FINISHED OPENING
2 5/8"
A-33SCALE 1/2 FULL SIZE
1"
1 3/8"
6 3/4"
FIN
IS
HE
D O
PE
NIN
G
6
1 5
/8
"
5
STANDARD ALUMINUM PRODUCTS INC.
5
ANY NUMBER OF PANELS
OXX
6
RECESSED TRACK
3 1
/8
"
A-34SCALE 1/2 FULL SIZE
Multi Sliders ProfileSD 1750 Mall Sliders
7/8
"
4321
OXX
STANDARD ALUMINUM PRODUCTS INC.
Multi Sliders ProfileSD 1750 Mall Sliders
FINISHED OPENING
1 2 3 4
FIXED JAMB
LOCKING JAMB
A-35SCALE 1/2 FULL SIZE
OXXX
A-36
FINISHED OPENING
SCALE 1/2 FULL SIZE
SD 1750 Mall SlidersMulti Sliders Profile
STANDARD ALUMINUM PRODUCTS INC.
1 2 3 4
6
7
FIXED JAMB
1 2 3
5
STANDARD ALUMINUM PRODUCTS INC.
SD 1750 Multi Slider ProfilesEgress Door Option
LOCKING JAMB
4 5
FINISHED OPENING
A-37SCALE 1/2 FULL SIZE
FIN
IS
HE
D O
PE
NIN
G
3 1
/8
"
RECESSED TRACK
7
STANDARD ALUMINUM PRODUCTS INC.
6
Egress Door OptionSD 1750 Multi Slider Profiles
1 5
/8
"
A-38SCALE 1/2 FULL SIZE
7/8
"
STANDARD ALUMINUM PRODUCTS INC.
A-39
321
OXO
STANDARD ALUMINUM PRODUCTS INC.
Multi Sliders ProfileSD 1750 Mall Sliders
FINISHED OPENING
1 2
FIXED JAMB
(Optional)
Double Glazed S/U
A-40SCALE 1/2 FULL SIZE
4
STANDARD ALUMINUM PRODUCTS INC.
SD 1750 Mall SlidersMulti Sliders Profile
FINISHED OPENING
3 4
FIXED JAMB
OXO
LOCKING STILES
A-41SCALE 1/2 FULL SIZE
1 23 4
OXXO
STANDARD ALUMINUM PRODUCTS INC.
Multi Sliders ProfileSD 1750 Mall Sliders
1 2 3 4 5
FINISHED OPENING
1 2 3
FIXED JAMB
A-42SCALE 1/2 FULL SIZE
Multi Sliders ProfileSD 1750 Mall Sliders
STANDARD ALUMINUM PRODUCTS INC.
FINISHED OPENING
4 5
FIXED JAMB
OXXO
3
SCALE 1/2 FULL SIZE
A-43
1 2 3 4 5
SD 1750 Pocket DoorSTANDARD ALUMINUM PRODUCTS INC.
Profiles
1 2
FINISHED OPENING
1 2
P X
POCKET SIZE
(Optional)
Double Glazed S/U
A-44SCALE 1/2 FULL SIZE
(2
1
/4
" T
ra
ck +
1
/2
")
Min
im
um
SD 1750 Mall Sliders PocketSTANDARD ALUMINUM PRODUCTS INC.
Door Profiles
5
4
3
4
3
5
P X
FIN
IS
HE
D O
PE
NIN
G
1 5
/8
"
OPTIONAL.625 MUNTIN
SURFACE MOUNTEDTRACK
A-45SCALE 1/2 FULL SIZE
3 1
/8
"
7/8
"
STANDARD ALUMINUM PRODUCTS INC.
POCKET SIZE
6
FINISHED OPENING
8
P X X
6 7 8
7
SD 1750 Pocket DoorProfiles
(N
o o
f T
ra
cks x 2
1
/4
" +
1
/2
")
Min
im
um
A-46SCALE 1/2 FULL SIZE
STANDARD ALUMINUM PRODUCTS INC.
10
FIN
IS
HE
D O
PE
NIN
G
9
3 1
/8
"
4 1/2"
9 9
10 10
P X X XP X X X P
RECESSEDTRACK
Door ProfilesSD 1750 Mall Sliders Pocket
1 5
/8
"
A-47SCALE 1/2 FULL SIZE
7/8
"
POCKET SIZE
11
FINISHED OPENING
11
P
12 13 14 15
X X X X P
12 13
SD 1750 Pocket DoorProfiles
STANDARD ALUMINUM PRODUCTS INC.
A-48SCALE 1/2 FULL SIZE
(N
o o
f T
ra
cks x 2
1
/4
" +
1
/2
")
Min
im
um
STANDARD ALUMINUM PRODUCTS INC.
POCKET SIZEFINISHED OPENING
13 14 15
SD 1750 Pocket DoorProfiles
P X X X X P
A-49SCALE 1/2 FULL SIZE
11 12 13 14 15
(N
o o
f T
ra
cks x 2
1
/4
" +
1
/2
")
Min
im
um
SD 1750 HardwareSTANDARD ALUMINUM PRODUCTS INC.
Back Roller For Pocket
6 1/8"
7/8
"
5 3/4"
156mm
22
mm
Slider Side Adjustment
4 11/16"
199mm
B
A
1 1
/4
"
31
mm
1/8"
3mm
REFER TO TABLE
A-50
146mm
SD 1750 HardwareSTANDARD ALUMINUM PRODUCTS INC.
REQUIREMENTS.
FOR LOAD & QUALITY
250 lbs.
.437.78
1.51.5D-5350 SVO 1.135
WGT.
CAP.
EST.
RANGE
LOAD
1 1/2" STEEL
WHEEL
DESCRIPTION
DESCRIPTION
CBA
INCHES
1/2" DIA. x 82° CSK1/4"-20 THD. 2-HOLES
1/2" SPRING LOADED ANTI JUMP TRAVELTHROUGHOUT ENTIRE ADJUSTMENT RANGE
4 1/2"
1 1/2" 1 5/8"
A
.937
.843
1/4"-20 THD2 HOLES
B
A-51SCALE 1/2 FULL SIZE
C
STANDARD ALUMINUM PRODUCTS INC.
A-52
SD2000 Top Hung SliderSTANDARD ALUMINUM PRODUCTS INC.
Specifications
A-53
HARDWARE
Hardware for aluminum doors and
door frames shall be the entrance
manufacturer's standard:
1. M.S. hook bolt
2. Cylinder
3. Thumbturn
4. Flush finger pulls
5. Tandem Rollers
6. Roller Handles
The locking jamb with the lock cutout
is furnished loose. If custom hardware
is to be furnished by others,
templates and physical hardware
must be submitted prior to any
fabrication.
CONSTRUCTION
Standard Aluminum's SD2000 Series
multi track sliding front offers
unrestricted design options for easy
traffic flow. Multi track units with
parallel stacking for a variety of
interior applications. Moveable panels
can be stacked inline behind a wall, a
fixed end panel or an adjacent pocket.
The floor track may be either
recessed or surface applied. Each
sliding door panel has two tandem
steel rollers to provide easy operation
and longevity. All doors and
components are either manufactured
or assembled by our trained and
experienced technicians.
PERFORMANCE REQUIREMENTS
Ideally suited for show rooms,
shopping malls and office buildings.
The SD2000 has been used in
high-end residential applications
where a more substantial sliding door
is required. For this application
additional weather stripping is applied
to the sill. he SD2000 is generally
assembled with the sliding panel to
the inside but can be made with the
sliding panel to the outside with
additional sill weathering when
required.
Glass stops available:
1. Square single glazing
2. Sealed unit glazing
GENERAL DESCRIPTION
Work Included: The glazing
contractor shall furnish all
necessary materials, labour and
equipment for the complete
installation of aluminum entrance
doors, door frames and hardware
as detailed on the drawings and
specified herein.
Work Not Included: Structural
support of the framing system,
wood framing, structural steel,
masonry and final cleaning.
MATERIAL
All extruded aluminum shall be
6063 alloy with a minimum T-5
temper. The thickness of the
section varies from 0.150 at web
section to .0110 on non-bearing
wall surfaces. Glazing gaskets
shall be EPDM elastomeric
extrusions.
FINISH
Both anodized and painted
sections are available. All
intergral colour anodizing is
Architectural Class II., 0.4 to 0.7
mil. coating. A fluoropolymer
paint coating conforming to the
requirements of AAMA 603 and
AAMA 605 specifications, the
toughest coating in the industry
standards.
Door panels are constructed from
6063-T5 alloy while the base
track is extruded from 6061-T6
alloy and hard coat clear
anodized to extend wear and
reduces friction from the tandem
rollers
OPTIONAL ACCESSORIES
Many options are available to the
designer such as:
1. Egress Door
2. Muntins and Panels
3. Higher Base Rail
PROTECTION AND CLEANING
After installation the general
contractor should adequately
protect the exposed aluminum
and glass surfaces from damage
by others trades. i.e. (but not
restricted to) cement splash and
leach, grinding, polishing
compounds, plaster, paint, lime,
acids and other contaminants.
Top Rail Height 3.125”
Bottom Rail Height 3.125”
Stile Width 2.00”
Door Thickness 1.75”
Top Track/Jamb 1.625”
STANDARD ALUMINUM PRODUCTS INC.
2
1
2
1
4 1/2"
OX
MOUNTING
SHOE
A-54SCALE 1/2 FULL SIZE
Multi Sliders ProfileSD2000 Top Hung Slider
SLIDING GUIDE
5
3
16
"
4
3
16
"
1 5
/8
"
3 4 5
1
4
"
SD2000 Top Hung SliderSTANDARD ALUMINUM PRODUCTS INC.
Multi Sliders Profile
3 4 5
FIXED JAMB
LOCKING JAMB
3 4 5
FINISHED OPENING
2 5/8"
A-55SCALE 1/2 FULL SIZE
SLIDING GUIDE
1"
1 3/8"
2
1
OX
SD2000 Top Hung SliderSTANDARD ALUMINUM PRODUCTS INC.
Multi Sliders Profile
FIXED JAMB
6
A-56SCALE 1/2 FULL SIZE
OXO
9876
7
1
2
FINISHED OPENING
SD2000 Top Hung SliderSTANDARD ALUMINUM PRODUCTS INC.
Multi Sliders Profile
A-57SCALE 1/2 FULL SIZE
SLIDING GUIDE
8 9
OXO
9876
1
2
FINISHED OPENING
FIXED JAMB
SD2000 Top Hung SliderSTANDARD ALUMINUM PRODUCTS INC.
Multi Sliders Profile
A-58SCALE 1/2 FULL SIZE
11
OXXO
10 11 12 13 14
FIXED JAMB
10
SLIDING GUIDE
12
2
1
FINISHED OPENING
SD2000 Top Hung SliderSTANDARD ALUMINUM PRODUCTS INC.
Multi Sliders Profile
A-59SCALE 1/2 FULL SIZE
FIXED JAMB
SLIDING GUIDE
13 14
OXXO
10 11 12 13 14
2
1
FINISHED OPENING
SD2000 Top Hung SliderSTANDARD ALUMINUM PRODUCTS INC.
Profiles
A-60SCALE 1/2 FULL SIZE
2
1
1
2
P X
1 5
/8
"
SLIDING GUIDE
3
4
"
1
4
"
1
8
"
3 4
FINISHED OPENING
3 4
P X
POCKET SIZE
(Optional)
Double Glazed S/U
SD2000 Top Hung SliderSTANDARD ALUMINUM PRODUCTS INC.
Door Profiles
A-61SCALE 1/2 FULL SIZE
SLIDING GUIDE
STANDARD ALUMINUM PRODUCTS INC.
A-62
BF 2000 Bi- FoldSTANDARD ALUMINUM PRODUCTS INC.
Door Specifications
A-63
HARDWARE
Hardware for BF 2000 Bi-Fold door
panels shall be the manufacturer's
standard:
1. Two Point M.S. hook bolt
2. Cylinder
3. Thumbturn
4. Cylinder Operated Flushbolts
5. Flush Finger Pulls
6. Top hung steel ball bearing wheels
7. Continuous Gear Hinge
If custom hardware is to be furnished
by others, templates and physical
hardware must be submitted prior to
any fabrication.
CONSTRUCTION
Standard Aluminum's BF 2000 Series
door panels are assembled with
continuous gear hinges which bonds
the door panels into one continuous
unit. Also providing a weatherproof
and tamperproof barrier. Pivoted by
walking beam pivots at one end. Top
hung steel ball bearings wheels
prevent foreign material from affecting
smoothness of operation. Maximum
door weight 200lbs. All doors and
components are either manufactured
or assembled by our trained and
experienced technicians.
Please contact Standard Aluminum
Products for your design options.
PERFORMANCE REQUIREMENTS
BF 2000 top hung bi-folding doors
provide a clear opening for
restaurants, cafes, conference
centres, or hospital ICU rooms.
Glass stops available:
1. Square single glazing
2. Sealed unit glazing
GENERAL DESCRIPTION
Work Included: The glazing
contractor shall furnish all
necessary materials, labour and
equipment for the complete
installation of aluminum entrance
doors, door frames and hardware
as detailed on the drawings and
specified herein.
Work Not Included: Structural
support of the framing system,
wood framing, structural steel,
masonry and final cleaning.
MATERIAL
All extruded aluminum shall be
6063 alloy with a minimum T-5
temper. The thickness of the
section varies from 0.150 at web
section to .0110 on non-bearing
wall surfaces. Glazing gaskets
shall be EPDM elastomeric
extrusions.
FINISH
Both anodized and painted
sections are available. All
intergral colour anodizing is
Architectural Class II., 0.4 to 0.7
mil. coating. A fluoropolymer paint
coating conforming to the
requirements of AAMA 603 and
AAMA 605 specifications, the
toughest coating in the industry
standards.
Door panels are constructed from
6063-T5 alloy
OPTIONAL ACCESSORIES
Many options are available to the
designer such as:
1. Muntins and Panels
2. Higher Base Rail
3. Wider Stiles
PROTECTION AND CLEANING
After installation the general
contractor should adequately
protect the exposed aluminum
and glass surfaces from damage
by others trades. i.e. (but not
restricted to) cement splash and
leach, grinding, polishing
compounds, plaster, paint, lime,
acids and other contaminants.
Top Rail Height 3.125”
Bottom Rail Height 3.125”
Stile Width 2.00”
Door Thickness 1.75”
Top Track 1.625”
Bi-Fold Door ProfileSTANDARD ALUMINUM PRODUCTS INC.
1 2
A-64SCALE 1/2 FULL SIZE
4 3/8"
(Optional)
Double Glazed S/U
6
7 8Option
9
10Option
Option
142
6
7 8Option
9
10Option
Option
12321 1
111mm
3
STANDARD ALUMINUM PRODUCTS INC.
Bi-Fold Door Profile
3 3
/4
"
4
6
7
A-65SCALE 1/2 FULL SIZE
RECESSED CHANNEL
SLIDING GUIDE
3 3
/4
"
8
1
4
"
1
5 8
"
41
mm
95
mm
95
mm
1
8
"
Bi-Fold Door ProfileSTANDARD ALUMINUM PRODUCTS INC.
A-66SCALE 1/2 FULL SIZE
1 3
/4
"
45
mm
1 3
/4
"
45
mm
SLIDING GUIDE
9
10
1
5 8
"
1
8
"
STANDARD ALUMINUM PRODUCTS INC.
Bi-Fold Door Profile
A-67SCALE 1/2 FULL SIZE
1 3/4"
45mm
4 1/8"
105mm
8 7/16"
214mm
2 5
/8
"
67
mm
Beam
Walking
Roller
Top Hung
2 OR 4 PANEL FOLDING DOORPIVOT LAYOUT
4 5/16"
110mm
13
16
"
1 3/4" 1 3/4"
CL
Bi-Fold Door ProfileSTANDARD ALUMINUM PRODUCTS INC.
A-68SCALE 1/2 FULL SIZE
3 PANEL FOLDING DOORPIVOT LAYOUT
1 3/4"
45mm
4 1/8"
105mm
11"
279mm
2 5
/8
"
67
mm
Beam
Walking
6 7/8"
175mm
13
16
"
1 3/4" 1 3/4"
Roller
Top Hung
13
16
"
1 3/4"
CL