ssv60132 & ssv60132 dw -...

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0002486 REV B 5/22/07

SSV60132 & SSV60132 DW

SSV60132 Hoist Alum SS V-Frame6243601 BigWheel-LiftShoreStation68208 HardwareBox-SSV60132Hoist61427 LegBraceBundle-V6013262509 LowerFrameBundle-V6013262513 BasePadBundle62867 PlatformBundle-V601326485001 WinchBundle-5&6000w/WheelLift65025 WinchTubeBundle-V6013268207 LegBundle-V60132HA0024 MotorStopBundleAlum5”V-FrameHA0021 BunkPolyV40H-50108/120-60132H69604 LitPacket,V60132/DWNOTE: When referencing the front of hoist, this represents the winch end. When referencing the hoist end, this represents opposite of the winch end. Winch side is also referred to the right side of the hoist.

SSV60132 DW Hoist Alum SS V-Frame6243601 BigWheel-LiftShoreStation68208 HardwareBox-SSV60132Hoist61427 LegBraceBundle-V6013262509 LowerFrameBundle-V6013262513 BasePadBundle62867 PlatformBundle-V601326485001 WinchBundle-5&6000w/WheelLift65025 WinchTubeBundle-V6013268210 LegBundle-V60132DWHA0024 MotorStopBundleAlum5”V-FrameHA0021 BunkPolyV40H-50108/120-60132H69604 LitPacket,V60132/DW

SSV60132 Shown in Drawing


Winch Post Assembly Guide Post Assembly


Lower Frame Assembly


Platform Assembly


Winch Tube

WINCH TUBE SERVICE INSTRUCTIONS

Thewinchtubeassemblywaspre-assembledatthefactory.Itisimportantthattheinternalpartsandcableroutingsareassembledproperlyinorderforthewinchtubeassemblytofunctionproperly.Italsorequiresspecialtoolsduringtheas-semblyprocess.Itisthereforerecommendedthatyoucon-tactyourlocaldealershouldyoueverhaveissueswiththewinchtubeassembly.


Wheel Assembly


Winch Assembly


Brace Tube Assembly


Bunk Assembly


HA0024 - Motor Stop

Assembly InstructionsLocatethetwomotorstopmountingarms(Item#4)andthemotorstopassemblythatispre-assembledatthefactory.

Notethatthealuminumextrusioninthemotorstopassemblyhastwoholespre-drilledinonelegoftheextrusion.Positionthemotorstopassemblysothatthedrilledlegistothetopasshown.Locatea3/8”x1¾”hexboltanddrop it into thehole in the top legofthealuminumextrusion.Positionthemotorstopmountingarmasshownsothatitisonthebottomsideofthetoplegofthealumi-numextrusion.Aligntheholeintheendofthemotorstopmountingarmwiththebolt just installed.Insertthebolt throughtheholeinthe motor stop mounting arm. Secure with a 3/8” flange lock nut. Tighten.Taptheblackplasticcapsintotheotherendofthemotorstopmountingarms.

Repeat step three on the remaining motor stop mountingarm.

InstallationLocate the two hoist motor stop U-bolt brackets with theoffset(Item#1)andpositionthemasshowninthediagramonthetop side of the hoist platform so they are spaced correctly to fit the motorstopassembly.Theoffsetmustbeplacedasshowntocom-pensatefortheV-shapeintheplatform.

Place the motor stop assembly on the two hoist motorstop U-bolt brackets with offset just positioned. Drop the3/8” x 2 5/8” x 7 ½” U-bolts over the motor stop mountingarms, then down through the holes provided in the motorstopU-boltbracketswiththeoffset.

Push the U-bolts all the way down until the tops of theU-bolts are resting on the motor stop mounting arms.Place a straight motor stop U-bolt bracket on the U-boltlegs on the bottom side of the platform. Secure in placewith 3/8” lock washers and hex nuts. Hand tighten only atthispoint.

Repeat steps 5, 6 and 7 on the other motor stop mountingarm.

AdjustmentPosition the hoist motor stop assembly on the hoist so itis centered side to side on the hoist platform. Changingthe motor stop location front to rear is accomplished bysliding the straight portion of the motor stop arm throughthe U-bolts. This allows you to change the motor stoplocation to best position your boat on the hoist. Once theassembly is in the proper position, tighten the nuts on theU-bolts.


DW (Deep Water) SECTION:

Thedeepwaterversionofthisboathoistisassembledusingthesameassemblyinstructionsasthestandardhoist.Theonlyitemsthataredifferentbetweenthetwohoistsarethelengthoftheup-right corner posts and the adjustable legs inside them as identified inthedrawingsfordeepwaterlegs.

Thewaterdepthwhereyourhoistisgoingtobeinstalledwilldeter-minewhetheryoushouldusethedeepwaterversionofthishoist.

Thedeepwaterversionof thishoist canbeused indeeperwa-terdepthsbecauseoftheadditionallengthoftheextensionlegs.Listedbelowistheamountofadjustmentthevariouslegshave.

• A standard leg shipped with the hoist has 20” of adjustment.

• Thedeepwaterlegshave55”ofadjustment.


1/2” X 4” Hex Bolt - Qty: 1 (0110114)

1/2” X 5-1/2” Hex Bolt - Qty: 12 (0110125)

3/8” X 7” Hex Bolt - Qty: 16 (0110070)

3/8” X 2” Hex Bolt - Qty: 10 (0110048)

3/8” X 1-1/2” Hex Bolt - Qty: 13 (0140045)

5/16” X 3/4” Hex BoltQty: 16 (0140022)

3/8” X 3/4” Carriage BoltQty: 8 (0210100)

1/2” Flange Lock NutQty: 13 (1440102)

1/2” Flat WasherQty: 24 (1340100)

3/8” Flat WasherQty: 92 (1340095)

3/8” Flange Lock NutQty: 79 (1440101)

5/16” Flat WasherQty: 16 (1310085)

5/16” Lock WasherQty: 16 (1310025)

5/16” Hex NutQty: 16 (1410069)

5/8” Flat WasherQty: 6 (1340105) 5/8” Brass Hex Nut

Qty: 6 (1410362)

0160043 Pre-Packaged Hardware Bag

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0002486Page 32 REV B 5/22/07

ShoreStation Decal Placementfor Model SSV60132

4850351Spinning WheelDanger Decal

4811312Clamp Arrow Decal

4811319Adj. Gauge Decal

4850394Max Load Decal

4850363Safety Decal

4850408Not A Step Decal

4810700Big Wheel Decal

4850224Inspect Cable Caution Decal

4850206Lube Tube

Decal

4811312 Clamp Arrow Decal

4811319Adj. Guage Decal

4850359Directional

Arrow Decal

4811394 MaximumLoadDecal-WinchTube4850351 SpinningWheelDangerDecal4811312 ClampArrowDecal4811319 Adj.GaugeDecal4850363 SafetyDecal4850408 NotAStepDecal4850206 LubeTubeDecal4850359 DirectionalArrowDecal4850224 InspectCableCautionDecal4810700 BigWheelDecal

SSV60132 Decal Placement

ssv60132 & ssv60132 dw -...

Documents