ss/264xs 1 2600t series pressure transmitters · 2014-05-28 · data sheet ss/264xs_1 abb 2600t...

Data SheetSS/264XS_1

ABB 2600T SeriesEngineered solutions

for all applications

Base accuracy : ±0.075%

Span limits– 0.134 to 16000kPa; 0.54inH2O to 2320psi– 0.27 to 16000kPa abs; 2mmHg to 2320psia

Reliable sensing system coupled with very latestdigital technologies– provides large turn down ratio up to 100:1

Comprehensive sensor choice– optimize in-use total performance and stability

5–year stability

Flexible configuration facilities– provided locally via local keys combined with LCD

indicator or via hand held terminal orPC configuration platform

Multiple protocol availability– provides integration with HART®, PROFIBUS PA

and FOUNDATION Fieldbus platforms offeringinterchangeability and transmitter upgradecapabilities

Full compliance with PED Category IV– suitable for safety accessory application

FieldIT

2600T Series Pressure Transmitters

Model 264DS Differential Model 264PS Gauge

Model 264VS Absolutemaximum working pressure up to 21MPa, 3045psi

2600T Pressure TransmittersModel 264DS, 264PS, 264VS SS/264XS_1

2

DampingSelectable time constant : 0, 0.25, 0.5, 1, 2, 4, 8 or 16s.This is in addition to sensor response time

Turn on time

Operation within specification in less than 1s with minimumdamping.

Insulation resistance

> 100MΩ at 1000VDC (terminals to earth)

Span limits

Maximum span = URL(can be further adjusted up to ± URL (TD = 0.5) for differentialmodels, within the range limits)

IT IS RECOMMENDED TO SELECT THE TRANSMITTER SENSORCODE PROVIDING THE TURNDOWN VALUE AS LOWEST ASPOSSIBLE TO OPTIMIZE PERFORMANCE CHARACTERISTICS.

Zero suppression and elevation

Zero and span can be adjusted to any value within the range limitsdetailed in the table as long as:

– calibrated span ≥ minimum span

Functional Specifications

Range and span limits

rosneSedoC

egnaRreppU)LRU(timiL

)LRL(timiLegnaRrewoL napsmuminiM

SD462laitnereffid

SP462eguag

SV462etulosba

laitnereffidSD462eguagSP462

SV462etulosba

BaPk4

rabm04Hni61 2O

aPk4–rabm04–

Hni61– 2O

aPk4–rabm04–

Hni61– 2O

aPk431.0rabm43.1

Hni45.0 2O

EaPk61

rabm061Hni46 2O

aPk61–rabm061–

Hni46– 2O

aPk61–rabm061–

Hni46– 2O

sbaaPk70.0sbarabm7.0

gHmm5.0

aPk72.0rabm7.2

Hni80.1 2O

aPk72.0rabm7.2

gHmm2

FaPk04

rabm004Hni061 2O

aPk04–rabm004–

Hni061– 2O

aPk04–rabm004–

Hni061– 2O


gHmm5.0

aPk4.0rabm4

Hni6.1 2O

aPk76.0rabm7.6

gHmm5

GaPk56

rabm056Hni062 2O

aPk56–rabm056–

Hni062– 2O

aPk56–rabm056–

Hni062– 2O


gHmm5.0

aPk56.0rabm5.6

Hni6.2 2O

aPk1.1rabm11gHmm8

HaPk061

rabm0061Hni246 2O

aPk061–rabm0061–

Hni246– 2O

sbaaPk1sbarabm01

aisp51.0


gHmm5.0

aPk6.1rabm61

Hni4.6 2O

aPk76.2rabm7.62

gHmm02

MaPk006

rab6isp78

aPk006–rab6–isp78–

sbaaPk1sbarabm01

aisp51.0


gHmm5.0

aPk6rab60.0isp78.0

aPk01rab1.0isp54.1

PaPk0042

rab42isp843

aPk0042–rab42–isp843–

sbaaPk1sbarabm01

aisp51.0


gHmm5.0

aPk42rab42.0

isp5.3

aPk04rab4.0isp8.5

QaPk0008

rab08isp0611

aPk0008–rab08–

isp0611–

sbaaPk1sbarabm01

aisp51.0


gHmm5.0

aPk08rab8.0isp6.11

aPk431rab43.1isp4.91

SaPk00061

rab061isp0232

aPk00061–rab061–isp0232–

sbaaPk1sbarabm01

aisp51.0


gHmm5.0

aPk061rab6.1isp2.32

aPk762rab76.2isp7.83


3

Operative limits

Temperature limits °C (°F) :

Ambient (is the operating temperature)

Lower ambient limit for LCD indicators: –20°C (–4°F)

Upper ambient limit for LCD indicators: +70°C (+158°F)

Note : For Hazardous Atmosphere applications see the temperaturerange specified on the certificate/approval relevant to the aimedtype of protection

Process

Lower limit

– refer to lower ambient limits; –20°C (–4°F) for Viton gasket

Upper limit

– Silicone oil and ABB fill: 121°C (250°F) (1)

– Inert fluid: 100°C (212°F) (2)

(1) 100°C (212°F) for application below atmospheric pressure

(2) 65°C (150°F) for application below atmospheric pressure

Storage

Lower limit: –50°C (–58°F); –40°C (–40°F) for LCD indicators

Upper limit: +85°C (+185°F)

Pressure limits

Overpressure limits (without damage to the transmitter)

0.067kPa abs, 0.67mbar abs, 0.01psia (double with inert filling) to

– 7MPa, 70bar, 1015psi for sensor code B

– 16MPa, 160bar, 2320psi for sensor code E

– 21MPa, 210bar, 3045psi for sensor codes F to S

Static pressure

Transmitters for differential pressure model 264DS operates withinspecifications between the following limits

– sensor code B:1.3kPa abs,13mbar abs, 0.2psia and 7MPa, 70bar, 1015psi

– sensor code E:1.3kPa abs,13mbar abs, 0.2psia and 16MPa, 160bar, 2320psi

– sensor codes F to S:1.3kPa abs,13mbar abs, 0.2psia and 21MPa, 210bar, 3045psi

Proof pressure

The transmitter can be exposed without leaking to line pressure of upto 48MPa, 480bar, 6960psi. Meet ANSI/ISA–S 82.03 hydrostatic testrequirements and SAMA PMC 27.1.

Environmental limits

Electromagnetic compatibility (EMC)

Comply with EN 61000–6–3 for emission and EN 61000–6–2 forimmunity requirements and test;

Radiated electromagnetic immunity level: 30V/m(according to IEC 1000–4–3, EN61000–4–3)

Conducted electromagnetic immunity level : 30V(according to IEC 1000–4-6, EN 61000–4–6)

Surge immunity level (with surge protector): 4kV(according to IEC 1000-4–5 EN 61000–4–5)

Fast transient (Burst) immunity level: 4kV(according to IEC 1000–4–4 EN 61000–4–4)

Pressure equipment directive (PED)

Comply with 97/23/EEC Category IV Modules D and B.

Humidity

Relative humidity: up to 100% annual average

Condensing, icing: admissible

Vibration resistance

Accelerations up to 2g at frequency up to 1000Hz(according to IEC 60068–2–26)

Shock resistance

Acceleration: 50g

Duration: 11ms

(according to IEC 60068–2–27)

Wet and dust-laden atmospheres

The transmitter is dust and sand tight and protected against immersioneffects as defined by EN 60529 (1989) to IP 67 (IP 68 on request) or byNEMA to 4X or by JIS to C0920.

Hazardous atmospheres

With or without output meter/integral display– INTRINSIC SAFETY/EUROPE:

ATEX/ZELM approvalII 1 GD T50°C, EEx ia IIC T6 (–40°C ≤ Ta ≤+40°C)T95°C, EEx ia IIC T4 (–40°C ≤ Ta ≤+85°C)

– TYPE "N"/EUROPE:ATEX/ZELM type examination (for HART)II 3 GD T50°C, EEx nL IIC T6 (–40°C ≤ Ta ≤+40°C)

T95°C, EEx nL IIC T4 (–40°C ≤ Ta ≤+85°C)(FOUNDATION Fieldbus/PROFIBUS PA): pending

– FLAMEPROOF/EUROPE:ATEX/CESI approvalII 1/2 GD T85°C, EEx d IIC T6 (–40°C ≤ Ta ≤ +75°C)

– CANADIAN STANDARDS ASSOCIATIONand FACTORY MUTUAL:– Explosionproof: Class I, Div. 1, Groups A, B, C, D– Dust ignitionproof : Class II, Div. 1, Groups E, F, G– Suitable for : Class II, Div. 2, Groups F, G; Class III, Div. 1, 2– Nonincendive: Class I, Div. 2, Groups A, B, C, D– Intrinsically safe: Class I, II, III, Div. 1, Groups A, B, C, D, E, F, G

AEx ia IIC T6/T4, Zone 0 (FM)– STANDARDS AUSTRALIA (SAA): pending

TS/WCA ApprovalEx d IIC T5 (Tamb +85°C)/T6 (Tamb +70°C) Class 1 Zone 1;Ex ia IIC T4 (Tamb +85°C) /T5 (Tamb +55°C) T6 Class 1 Zone 0

gnilliFSP462-SD462sledoM SV462ledoM

srosneSSotF

srosneSEotB

srosneSSotF

rosneSEedoc

enociliSlio

58+dna04–)581+dna04–(

58+dna52–)581+dna31–(

58+dna04–)581+dna04–(

07+dna51–)851+dna5+(

trenI58+dna02–)581+dna4–(

58+dna01–)581+dna41+(

56+dna01–)051+dna41+( elbacilppaton

llifBBA 58+dna02–)581+dna4–(

58+dna01–)581+dna41+(

58+dna01–)581+dna41+( elbacilppaton


4

Optional surge protection

Up to 4kV

– voltage 1.2 µs rise time / 50 µs delay time to half value

– current 8 µs rise time / 20 µs delay time to half value

Output signal

Two–wire 4 to 20mA, user-selectable for linear or square root output,power of 3/2 or 5/2, 5th order or two 2nd order switching point selectableprogrammable polynomial output.

HART® communication provides digital process variable (%, mA orengineering units) superimposed on 4 to 20mA signal, with protocolbased on Bell 202 FSK standard.

Output current limits (to NAMUR standard)

Overload condition

- Lower limit: 3.8mA

- Upper limit: 20.5mA

Transmitter failure mode (to NAMUR standard)

The output signal can be user-selected to a value of 3.7 or 22mA ongross transmitter failure condition, detected by self-diagnostics.

In case of CPU failure the output is driven <3.7mA or >22mA.

Electrical Characteristics and Options

HART digital communication and 4 to 20mA output

Power Supply

The transmitter operates from 10.5 to 42VDC with no load and isprotected against reverse polarity connection (additional load allowsoperations over 42VDC).

For EEx ia and other intrinsically safe approval power supply mustnot exceed 30VDC.

Ripple

20mV max on a 250Ω load as per HART specifications

Load limitations

4 to 20mA and HART total loop resistance :

A minimum of 250Ω is required for HART communication.

Optional indicators

Output meter

CoMeter and Prometer LCD :

5-digit (±99999 counts) programmable with 7.6mm. high (3in),7-segment numeric characters plus sign and digital point for digitalindication of output value in percentage, current or engineer unit;

10-segment bargraph display (10% per segment) for analogindication of output in percentage;

7-digit with 6mm. high (2.3in), 14-segment alphanumericcharacters, for engineer units and configuration display

Analog : 36mm (1.4in) scale on 90°.

Integral display

LCD, 15 lines x 56 column dot matrix providing 2 lines indication as

– top: 5-digit (numeric) plus sign or 7-digit alphanumeric

– bottom: 7-digit alphanumeric

and additional 50-segment bargraph for indication of analog outputin percentage.

User-definable matrix display mode with HART communication:

– process variable in pressure unit or

– output signal as percentage, current or engineering units

Display also indicates in/out transfer function, static pressure, sensortemperature and diagnostic messages and provides configurationfacilities.

R(kΩ) =Supply voltage – min. operating voltage (VDC)–––––––––––––––––––––––––––––––––––––––

22.5

(volts)

MINIMUM OPERATING VOLTAGES

10.5

with integral display

with optional output analog indicator

with optional surge protection

with ProMeter output indicator

10.7 12.3 12.5

no link on output indicator plugs

15.3

with CoMeter indicator and HART communication

13.3


5

PROFIBUS PA output

Device type

Pressure transmitter compliant to Profiles 3.0 Class A & B; ident.number 052B HEX.

Power supply

The transmitter operates from 10.5 to 32VDC , polarity independent.

For EEx ia approval power supply must not exceed 17.5VDC.Intrinsic safety installation according to FISCO model.

Current consumptionoperating (quiescent): 10.5mA

fault current limiting: 20mA max.

Output signal

Physical layer in compliance to IEC 1158–2/EN 61158–2 withtransmission to Manchester II modulation, at 31.25kbit/sec.

Output interface

PROFIBUS PA communication according to Profibus DP50170 Part 2/DIN 19245 part 1–3.

Output update time

25ms

Function blocks

2 analog input, 1 transducer, 1 physical

Integral display




and additional 50-segment bargraph for indication of output inpercentage of the analog input function block assigned to the primaryvariable.

User-definable matrix display mode:

– process variable in pressure units or

– primary variable in engineering units (output of transducer block) or

– output as percentage or engineering units of analog input functionblocks

Display also indicates diagnostic messages and providesconfiguration facilities.Secondary variable, static pressure and sensor temperature can beread.

Transmitter failure mode

On gross transmitter failure condition, detected by self-diagnostics,the output signal can be driven to defined conditions, selectable by theuser as safe, last valid or calculated value. If electronic failure or shortcircuit occur the transmitter consumption is electronically limited at adefined value (20mA approx), for safety of the network.

FOUNDATION Fieldbus output

Device type

LINK MASTER DEVICE

Link Active Scheduler (LAS) capability implemented.

Power supply

The transmitter operates from 9 to 32VDC, polarity independent.

For EEx ia approval power supply must not exceed 24VDC (entitycertification) or 17.5VDC (FISCO certification), according to FF–816.

Current consumption

operating (quiescent): 10.5mA

fault current limiting: 20mA max.

Output signal

Physical layer in compliance to IEC 1158–2/EN 61158–2 withtransmission to Manchester II modulation, at 31.25kbit/sec.

Function blocks/execution period

2 standard Analog Input blocks/25ms max (each)

1 standard PID block/70ms max.

Additional blocks

1 standard Resource block,

1 custom Pressure with calibration transducer block.

Number of link objects25

Number of VCRs

24

Output interface

FOUNDATION fieldbus digital communication protocol to standard H1,compliant to specification V. 1.5; FF registration in progress.

Integral display




and additional 50-segment bargraph for indication of output inpercentage of the analog input function block assigned to the primaryvariable.

User-definable matrix display mode:

– process variable in pressure units or

– primary variable in engineering units (output of transducer block) or

– output as percentage or engineering units of analog input functionblocks

Display also indicates diagnostic messages and providesconfiguration facilities.Secondary variable, static pressure and sensor temperature can beread.

Transmitter failure mode

The output signal is "frozen" to the last valid value on gross transmitterfailure condition, detected by self-diagnostics which also indicate aBAD conditions. If electronic failure or short circuit occur the transmitterconsumption is electronically limited at a defined value (20mA approx),for safety of the network.


6

Operating influences

Ambient temperature

per 20K (36°F) change between the limits of –20°C to +65°C (–4 to+150°F) :

Optional CoMeter and ProMeter ambient temperature

Total reading error per 20K (36°F) change between the ambient limitsof –20 and +70°C (-4 and +158°F) :

±0.15% of max span (16mA).

Static pressure (zero errors can be calibrated out at line pressure)

per 2MPa, 20bar or 290psi (sensor code B)

per 7MPa, 70bar or 1015psi (sensor codes E to S)

Model 264DS– zero error: ±0.08% of URL– span error: ±0.08% of readingMultiply by 2 the errors for sensor code E.

Supply voltage

Within voltage/load specified limits the total effect is less than0.005% of URL per volt.

Load

Within load/voltage specified limits the total effect is negligible.

Radio frequency interference

Total effect : less than 0.10% of span from 20 to 1000MHz and forfield strengths up to 30V/m when tested with shielded conduit andgrounding, with or without meter.

Common mode interference

No effect from 100Vrms @ 50Hz, or 50VDC

Mounting position

Rotations in plane of diaphragm have negligible effect. A tilt to 90°from vertical causes a zero shifts up to 0.5kPa, 5mbar or 2inH2O,which can be corrected with the zero adjustment. No span effect.

Stability

±0.10% of URL over a thirty-six-month period

Vibration effect

±0.10% of URL (according to IEC 61298–3)

URLSpan

URLSpan

URLSpan

Performance specificationsStated at reference condition to IEC 60770 ambient temperature of 20°C(68°F), relative humidity of 65%, atmospheric pressure of 1013hPa(1013mbar), mounting position with vertical diaphragm and zero basedrange for transmitter with isolating diaphragms in AISI 316 L ss or Hastelloyand silicone oil fill or ABB fill and HART digital trim values equal to 4–20mAspan end points, in linear mode.

Unless otherwise specified, errors are quoted as % of span.

Some performance data are affected by the actual turndown (TD) as ratiobetween Upper Range Limit (URL) and calibrated span.

IT IS RECOMMENDED TO SELECT THE TRANSMITTER SENSOR CODEPROVIDING THE TURNDOWN VALUE AS LOWEST AS POSSIBLE TOOPTIMIZE PERFORMANCE CHARACTERISTICS.

Dynamic performance (according to IEC 61298–1 definition)

Dead time: 40ms

Time constant (63.2% of total step change):

– sensors M to S: ≤ 70ms

– sensor H: 100ms

– sensor G: 130ms

– sensor F: 180ms

Response time (total) = dead time + time constant

Accuracy rating% of calibrated span, including combined effects of terminal basedlinearity, hysteresis and repeatability.

For fieldbus versions SPAN refer to analog input function block outscalerange

Model 264DS, 264PS– ±0.075% for TD from 1:1 to 15:1

(±0.10% for sensor code B for TD from 1:1 to 10:1)

– ±0.005% x for TD from 15:1 to 60:1(30:1 for sensor code E)

(±0.01% x for sensor code B for TD from 10:1 to 20:1)

Models 264VS– ±0.075% for TD from 1:1 to 10:1

– ±0.0075% x for TD from 10:1 to 20:1

ledoMrosneS

edoCDTrofotpu

SD462SP462

SotE 1:51 )naps%560.0+LRU%40.0(±

B 1:01 )naps%01.0+LRU%60.0(±SV462 SotE 1:01 )naps%31.0+LRU%80.0(±


7

Physical Specification(Refer to ordering information sheets for variant availability related tospecific model or versions code)

Materials

Process isolating diaphragms (*)

AISI 316 L ss; Hastelloy C276™; Monel 400™; Tantalum;

Hastelloy C276™ on AISI 316 L ss gasket seat.

Process flanges, adapters, plugs and drain/vent valves (*)

AISI 316 L ss; Hastelloy C276™; Monel 400™.

Blind flange (reference side of 264PS, 264VS)

AISI 316 L ss.

Sensor fill fluid

Silicone oil (DC200); inert fill (perfluorinated polyethers Galden™);"process-inert" fill (ABB fill).

Mounting bracket (**)

Zinc plated carbon steel with chrome passivation;

AISI 316 L ss.

Gaskets (*)

Viton™; PTFE.

Sensor housing

AISI 316 L ss.

Bolts and nuts

AISI 316 ss bolts Class A4–80 and nuts Class A4–70 per UNI 7323(ISO 3506);

AISI 316 ss bolts and nuts Class A4–50 per UNI 7323 (ISO 3506), incompliance with NACE MR0175 Class II.

Electronic housing and covers

Barrel version

– Copper-free content aluminium alloy with baked epoxy finish;

– Low-copper content aluminium alloy with baked epoxy finish;

– AISI 316 L ss.

DIN version

– Low-copper content aluminium alloy with baked epoxy finish.

Covers O-ring

Buna N.

Local zero and span adjustments:

Glass filled polycarbonate plastic (removable).

Tagging

AISI 316ss data plate attached to the electronics housing.

CalibrationStandard: at maximum span, zero based range, ambient temperatureand pressure;

Optional: at specified range and ambient conditions.

Optional extras

Mounting brackets

For vertical and horizontal 60mm. (2in) pipes or wall mounting.

Output indicator

plug-in rotatable type, LCD or analog.

Supplemental customer tag

AISI 316 ss tag screwed/fastened to the transmitter for customer's tagdata up to a maximum of 20 characters and spaces on one line for tagnumber and tag name, and up to a maximum of 3 spaced strings of 10characters each for calibration details (lower and upper values plusunit). Special typing evaluated on request for charges.

Surge protection (only as external unit for PROFIBUS PA and FF)

Cleaning procedure for oxygen service

Hydrogen or special service preparation

Test Certificates (test, design, calibration, material traceability)

Tag and manual language

Communication connectors

Process connectionson flanges : 1/4in NPT on process axis

on adapters : 1/2in NPT on process axis

centre distance (264DS): 54mm (2.13in ) on flange;51,54 or 57mm (2.01, 2.13 or 2.24in) as per adapters fittings

fixing threads: 7/16in–20 UNF at 41.3mm centre distance

Electrical connectionsTwo 1/2 NPT or M20x1.5 or PG 13.5 or 1/2 GK threaded conduitentries, direct on housing.

Special communication connector (on request)

– HART : straight or angle Harting HAN connector and one plug.

– FOUNDATION Fieldbus, PROFIBUS PA: M12x1 or 7/8.

Terminal block

HART version: three terminals for signal/external meter wiring up to2.5mm2 (14AWG) and three connection points for test andcommunication purposes.

Fieldbus versions: two terminals for signal wiring (bus connection)up to 2.5mm2 (14AWG)

Grounding

Internal and external 6mm2 (10AWG) ground termination points areprovided.

Mounting positionTransmitter can be mounted in any position.Electronics housing may be rotated to any position. A positive stopprevents over travel.

Mass (without options)3.5kg approx (8lb); add 1.5kg (3.4lb) for AISI housing.Add 650g (1.5lb) for packing.

PackingCarton 26 x 26 x 18cm approx (10 x 10 x 7in).


8

ConfigurationTransmitter with HART communication and 4 to 20 mA

Standard configuration

Transmitters are factory calibrated to customer's specified range.Calibrated range and tag number are stamped on the tag plate. If acalibration range and tag data are not specified, the transmitter will besupplied with the plate left blank and configured as follows:

Engineering Unit Specify from table4 mA Zero20 mA Upper Range Limit (URL)Output LinearDamping 1 sec.Transmitter failure mode UpscaleSoftware tag characters BlankOptional LCD output indicator 0 to 100.0% linear

Any or all the above configurable parameters, including Lowerrange–value and Upper range-value which must be the same unit ofmeasure, can be easily changed using the HART hand–heldcommunicator. The transmitter database is customized with specifiedflange type and material, O–ring and drain/vent materials and meter codeoption.Custom configuration (option)The following data may be specified in addition to the standardconfiguration parameters:

Descriptor 16 alphanumeric charactersMessage 32 alphanumeric charactersDate Day, month, year

Transmitter with PROFIBUS PA communicationTransmitters are factory calibrated to customer's specified range.Calibrated range and tag number are stamped on the tag plate. If acalibration range and tag data are not specified, the transmitter will besupplied with the plate left blank and configured as follows:

Measure Profile PressureEngineering Unit kPaOutput scale 0% Lower Range Limit (LRL)Output scale 100% Upper Range Limit (URL)Output LinearHi-Hi Limit Upper Range Limit (URL)Hi Limit Upper Range Limit (URL)Low Limit Lower Range Limit (LRL)Low-Low Limit Lower Range Limit (LRL)Limits hysteresis 0.5% of output scalePV filter 0 sec.Address (settable by local key) 126Tag 32 alphanumeric characters

Any or all the above configurable parameters, including Lower range-valueand Upper range–value which must be the same unit of measure, can beeasily changed by a PC running the configuration software Smart Visionwith DTM for 2600T. The transmitter database is customized with specifiedflange type and material, O–ring and drain/vent materials and meter codeoption.Custom configuration (option)The following data may be specified in addition to the standardconfiguration parameters:

Descriptor 32 alphanumeric charactersMessage 32 alphanumeric charactersDate Day, month, year

Transmitter with FOUNDATION FieldbuscommunicationTransmitters are factory calibrated to customer's specified range.Calibrated range and tag number are stamped on the tag plate. If acalibration range and tag data are not specified, the transmitter will besupplied with the plate left blank and the analog input function block FB1is configured as follows:

Measure Profile PressureEngineering Unit kPaOutput scale 0% Lower Range Limit (LRL)Output scale 100% Upper Range Limit (URL)Output LinearHi-Hi Limit Upper Range Limit (URL)Hi Limit : Upper Range Limit (URL)Low Limit Lower Range Limit (LRL)Low-Low Limit Lower Range Limit (LRL)Limits hysteresis 0.5% of output scalePV filter time 0 sec.Tag 32 alphanumeric characters

The analog input function block FB2 is configured for the sensor tempe-rature measured in °C. Any or all the above configurable parameters,including the range values, can be changed using any host compliant toFOUNDATION fieldbus. The transmitter database is customized withspecified flange type and material, O–ring and drain/vent materials andmeter code option.

For any protocol available engineering units of pressure measure are :Pa, kPa, MPainH2O@4°C, mmH2O@4°C, psiinH2O@20°C, ftH2O@20°C, mmH2O@20°CinHg, mmHg, Torrg/cm2, kg/cm2, atmmbar, bar

™ Hastelloy is a Cabot Corporation trademark

™ Monel is an International Nickel Co. trademark

™ Galden is a Montefluos trademark

™ Viton is a Dupont de Nemour trademark

(*) Wetted parts of the transmitter.

(**) U-bolt material: AISI 400 ss; screws material: high-strength alloy steel orAISI 316 ss.


9

135

(5.3

1)

(*)

62 (2.44)71 (2.80)

86 (3.39)

82 (3

.23)

+

127 (5.00)17 (0.67)

26 (1.02)17 (0.67)

36 (1.42)

MOUNTING DIMENSIONS (not for construction unless certified) – dimensions in mm (in)Transmitter with barrel aluminium housing on bracket for vertical or horizontal 60mm (2in) pipe mounting

(*) FOR MODEL 264DS51 (2.01), 54 (2.13) or 57 (2.24) mm (in) according to 1/2in 14 NPT adapters fitting; 54 (2.13) mm (in) on 1/4in 18 NPT process flangeFOR MODEL 264PS54 (2.13) mm (in) with low pressure side flange without process connection (a filter is fitted) and drain/vent valve

NOTE : Process connection, gasket groove and gaskets are in accordance with DIN 19213. Bolting threads for fixing adapter or other devices(i.e. manifold etc.) on process flange is 7/16in – 20 UNF.

Certificationlabel

Identification tagAdjustments

Terminalside

Electronicside

Integraldisplayhousing

Min. clearanceto removethe cover

Output meterhousing

Drain/ventValve

Barrel typehousing

Processconnection

Model 264VS

66 (2.60) with plug78 (3.07) with d/v valve

11 (0

.43)

102 (4.02)

84 (3.31)

108 (4.25)

41.3

(1.6

3)63

(2.4

8)16

7 (6

.57)

S

NOSSTIUCRIC

SEL

NOI

NETSOST U

RREVUOCEL

RED

RA

G

TNE'

MEF NE B EL CI

QUAT

E

ALSTIUCRI

C

I VE

H

COPEE

K

VERTIGT

E

H

WN

!

86 (3.39)

S

NOS

STIUC RI C SE L

NOINET

SO

ST

U

RRE

VUOCEL

REDRAG

TNE'

MEF

NEB

ELC

I

QUAT

E

ALS TI U CRI C

IVE

H

COPEEK

VER

TIGT

E

H

WN

!

108

(4.2

5)

82 (3.23)

Adapter

Electricalconnections

Flange

Covers lockingscrew

54 (2.13)

71 (2.80)

86 (3.39)

82 (3

.23)

62 (2.44)13

5 (5

.31)

+

127 (5.00)17 (0.67)

26 (1.02)17 (0.67)

36 (1.42)


10

Transmitter on bracket for vertical or horizontal 60 mm (2in) pipe mounting (DIN housing)

Transmitter with flanges for vertical connection (Barrel housing)

Adjustments


Certificationlabel

Outputmeter

housing

Terminalside

DIN typehousing

Electronicside

Drain/ventValve

Flange

Adapter

Identificationtag

Covers lockingscrew

Certificationlabel

Harting HANconnector

Externalground


108

(4.2

5)

82 (3.23)

26 (1

.02)

41.3 (1.63)

51 (2

.01)

33

(1.3

0)

63 (2.48)

179 (7.05)

17 (0

.67)

148 (5.83)36 (1.42)

17 (0.67)

55 (2.17) max 7 (0.28)14

2 (5

.59)

16 (0

.63)

86 (3.39)

S

NOSSTIUCRIC

SEL

NOI

NETSOST U

RREVUOCEL

RED

RA

G

TNE'

MEF NE B EL CI

QUAT

E

ALSTIU

CRIC

I VE

H

COPEE

K

VERTIGT

E

H

WN

!

+

127 (5.00)

17 (0.67)

26 (1.02)

17 (0.67)

36 (1.42)

54 (2.13)

71 (2.80) 62 (2.44)

86 (3.39)

185

(7.2

8)

86 (3.39)

S

NOSSTIUCRIC

SEL

NOI

NETSOST U

RREVUOCEL

RED

RA

G

TNE'

MEF NE B EL CI

QUAT

E

ALSTIU

CRIC

I VE

H

COPEE

K

VERTIGT

E

H

WN

!

83 (3

.27)

33 (1

.30) 41.3 (1.63)

74 (2.91)

Certificationlabel

Identification tagAdjustments

Terminalside

Electronicside


Min. clearanceto removethe cover

Output meterhousing

Drain/ventValve

Barrel typehousing

Processconnection

Adapter



11

Transmitter on bracket for wall mounting (by four M8 screws)

Transmitter with barrel AISI ss housing on bracket (flat type for box) for vertical or horizontal 60mm (2in)pipe mounting

70 (2.75)

84 (3

.31)

70 (2

.75)

204

(8.0

3)

98 (3.86)

+

25 (0.98)

47 (1.85)

S

NOSSTIUCRIC

SEL

NOI

NETSOST U

RREVUOCEL

RED

RA

G

TNE'

MEF NE B EL CI

QUAT

E

ALSTIU

CRIC

I VE

H

COPEE

K

VERTIGT

E

H

WN

!

70 (2

.75)

S

NOS

STIUC RI C SE L

NOINET

SO

ST

U

RRE

VUOCEL

REDRAG

TNE'

MEF

NEB

ELC

I

QUAT

E

ALS TI U CRI C

IVE

H

COPEEK

VER

TIGT

E

H

WN

!

70 (2

.75)

70 (2.75)

25 (1

)


12

Electrical connectionsHART Version

FIELDBUS Versions

+

+

-

-

++

--691HT

A B C

1

D E F

2

G H I

3

J K L

4

M N O

5

P Q R

6

S T U

7

V W X

8

Y Z #

9

@ % & /

0

+-

PV

REVIEW SERIALLINK

TRIM

F1 F2 F3 F4

CONF

M

Kent-Taylor

0

43

56 7 8

9

1020

40

0

60

100%

2 80

M+

-

- 1

54 6

23 8

7

+

TEST COMM

BUS CONNECTIONS

Internal groundtermination point

Fieldbus line

External groundtermination point

Test points4 to 20mA

Hartingpin

identification

Internal groundtermination point

External groundtermination point

Hand-heldcommunicator

GND

Line load

Remoteindicator

Powersource

250 ohm min

Receiver

HART hand-held communicator may be connected at any wiring termination point in the loop, providing the minimum resistanceis 250 ohm. If this is less than 250 ohm, additional resistance should be added to allow communications

Optional


13

BASIC ORDERING INFORMATION model 264DS Differential Pressure TransmitterSelect one character or set of characters from each category and specify complete catalog number.Refer to additional ordering information code and specify one or more codes for each transmitter if additional options are required.

LEDOMESAB 1– ts 5ot ht sretcarahc 2 6 4 D S X S X X X X X

%570.0YCARUCCAESAB–rettimsnarTerusserPlaitnereffiD

–stimilnapS-ROSNES 6 ht retcarahcaPk4dna431.0aPk61dna72.0

aPk04dna4.0aPk56dna56.0aPk061dna6.1

aPk006dna6aPk0042dna42aPk0008dna08

aPk00061dna061

rabm04dna43.1rabm061dna7.2

rabm004dna4rabm056dna5.6rabm0061dna61

rab6dna60.0rab42dna42.0


Hni61dna45.0 2OHni46dna80.1 2OHni061dna6.1 2OHni062dna6.2 2OHni246dna4.6 2Oisp78dna78.0isp843dna5.3

isp0611dna6.11isp0232dna2.32

BEFGHMPQS

edocesU 7– ht retcarahc

)strapdettew(diulflliF/lairetammgarhpaiD 8– ht retcarahc

ssL613ISIA)taesISIAno(™672CyolletsaH

™672CyolletsaH™004lenoM

mulatnaTssL613ISIA

)taesISIAno(™672CyolletsaH™672CyolletsaH

™004lenoMmulatnaT


™672CyolletsaH

lioenociliSlioenociliSlioenociliSlioenociliSlioenociliS

diulftrenIdiulftrenIdiulftrenIdiulftrenIdiulftrenI

llifBBAllifBBAllifBBA

)2etoN(

)2etoN()2etoN(

)2,1setoN()2,1setoN()2,1setoN()2,1setoN()2,1setoN(

)2etoN(

ECANECANECANECAN

ECANECANECANECAN

ECANECAN

SHKMTABFCDLQP

)strapdettew(noitcennocdnalairetamsretpada/segnalfssecorP – 9 ht retcarahc

)noitcennoclatnoziroH(ssL613ISIA)noitcennoclatnoziroH(ssL613ISIA

1/4 (tceridf-TPNni 7/ 61 )gnillird.S.UFNUni1/2 (retpadahguorhtf-TPNni 7/ 61 )gnillird.S.UFNUni

ECANECANECANECANECANECAN

AB

)noitcennoclatnoziroH(™672CyolletsaH)noitcennoclatnoziroH(™672CyolletsaH


DE

)noitcennoclatnoziroH(™004lenoM)noitcennoclatnoziroH(™004lenoM


GH

)noitcennoclacitreV(ssL613ISIA)noitcennoclacitreV(ssL613ISIA



QT

)noitcennoclacitreV(™672CyolletsaH)noitcennoclacitreV(™672CyolletsaH


MS

)noitcennoclacitreV(™004lenoM)noitcennoclacitreV(™004lenoM


UV

)strapdettew(teksaG/stloB 01– ht retcarahc

ss613ISIAss613ISIA

)aPM61=PWM(–)ECAN(ss613ISIA)aPM61=PWM(–)ECAN(ss613ISIA

™notiVEFTP™notiV

EFTP

)1etoN(

)1etoN(ECANECAN

1234

noitcennoclacirtcelednalairetamgnisuoH 11– ht retcarahc

)noisrevlerraB(yollamuinimulA)noisrevlerraB(yollamuinimulA)noisrevlerraB(yollamuinimulA)noisrevlerraB(yollamuinimulA)noisrevlerraB(yollamuinimulA)noisrevlerraB(yollamuinimulA

1/2 TPNni)02MC(5.1x02M

5.31gP1/2 KGni

rotcennocNAHgnitraHrotcennocsubdleiF

)ylnoesopruplareneg()3etoN()ylnoesopruplareneg()3etoN(


)ylnoesopruplareneg()3etoN()ylnoesopruplareneg()ylnoesopruplareneg(


ABDCEG

)noisrevlerraB(eerf-reppocyollamuinimulA)noisrevlerraB(eerf-reppocyollamuinimulA)noisrevlerraB(eerf-reppocyollamuinimulA)noisrevlerraB(eerf-reppocyollamuinimulA)noisrevlerraB(eerf-reppocyollamuinimulA)noisrevlerraB(eerf-reppocyollamuinimulA


5.31gP1/2 KGni


HLNMPR

)noisrevlerraB(ssL613ISIA)noisrevlerraB(ssL613ISIA)noisrevlerraB(ssL613ISIA)noisrevlerraB(ssL613ISIA)noisrevlerraB(ssL613ISIA


5.31gP1/2 KGni

rotcennocsubdleiF

STVUZ

)noisrevNID(yollamuinimulA)noisrevNID(yollamuinimulA)noisrevNID(yollamuinimulA)noisrevNID(yollamuinimulA

)02MC(5.1x02M5.31gP


JYKW

snoitpolanoitiddA/tuptuO 21– ht retcarahc

Am02ot4dnanoitacinummoclatigidTRAHAm02ot4dnanoitacinummoclatigidTRAH

APSUBIFORPAPSUBIFORP

subdleiFNOITADNUOFsubdleiFNOITADNUOF

snoitpolanoitiddaoN)"edocgniredrolanoitiddA"ybderedroebot(detseuqersnoitpO



)5,4setoN()4etoN(

)5,4setoN()5etoN(

)5,4setoN()5etoN(

H1P2F3


14

ADDITIONAL ORDERING INFORMATION for model 264DSAdd one or more 2-digit code(s) after the basic ordering information to select all required options

XX XX XX XX XX XX XX XX XX XX XX deunitnoC

)strapdettew()noitisopdnalairetam(evlavtnev/niarDssL613ISIAssL613ISIAssL613ISIA

™672CyolletsaH™672CyolletsaH™672CyolletsaH

™004lenoM™004lenoM™004lenoM

sixassecorpnopotedisegnalfno

mottobedisegnalfnosixassecorpno

potedisegnalfnomottobedisegnalfno


mottobedisegnalfno

)6etoN()7etoN()7etoN()8etoN()9etoN()9etoN()01etoN()11etoN()11etoN(

ECANECANECANECANECANECANECANECANECAN

1V2V3V4V5V6V7V8V9V

noitacifitreclacirtcelEaixEEytefaScisnirtnI–DG1yrogetaCIIpuorGXETA

dxEEfoorpemalF–DG2/1yrogetaCIIpuorGXETAecnailpmocngisedLnxEE"N"noitcetorpfoepyT–DG3yrogetaCIIpuorGXETA

ylno()ASC(noitaicossAdradnatSnaidanaC 1/2 )gnisuoh5.31gPdna02M,TPNni)21etoN(5T/6TCIIdxE+4T/5T/6TCIIaixEAASailartsuAsdradnatSotfoorpemalF–ytefaScisnirtnI

htiwylno(lavorppa)MF(lautuMyrotcaF 1/2 )noitcennoclacirtcele5.31gPdna02M,TPNni

1E2E3E4E5E6E

retemtuptuO

noitarbilacdradnatS,reteMorPnoitarbilaclaicepS,reteMorP

elacs%001–0raenilrotacidnituptuogolanAelacs01–0toorerauqsrotacidnituptuogolanA

)elacsraenilrofdeificepsebot(noitaudarglaiceps,rotacidnituptuogolanA)elacstoorerauqsrofdeificepsebot(noitaudarglaiceps,rotacidnituptuogolanA

)reteMoC(rotarugifnocTRAHdnaretemlangiselbammargorP)noitarugifnocremotsuc–reteMoC(rotarugifnocTRAHdnaretemlangiselbammargorP

)21etoN()21etoN()21etoN()21etoN()21etoN()21etoN()21etoN()21etoN(

1D2D3D4D5D6D7D8D

DCLlargetnIyalpsidlargetniDCLlatigiD 1L

)lairetamdnaepahs(tekcarbgnitnuoMgnitnuomepiproFgnitnuomepiproFgnitnuomllawroFgnitnuomllawroF

xobrofepyttalF

)gnisuohISIArofelbatiustoN()gnisuohISIArofelbatiustoN()gnisuohISIArofelbatiustoN()gnisuohISIArofelbatiustoN(

leetsnobraCssL613ISIAleetsnobraCssL613ISIAssL613ISIA

1B2B3B4B5B

egruSrotcetorPtneisnarT/egruS )21etoN( 1S

launamgnitarepOnamreG

nailatI1M2M

egaugnalgat&slebaLnamreG

nailatI1T2T

etalpgatlanoitiddAetalpleetssselniatsnogatfognitnirpresaL 2I

noitarugifnoCHni=erusserP–dradnatS 2 F.ged=erutarepmeT;C°02taisp/OHni=erusserP–dradnatS 2 F.ged=erutarepmeT;C°4taisp/OHni=erusserP–dradnatS 2 C.ged=erutarepmeT;C°02taisp/OHni=erusserP–dradnatS 2 C.ged=erutarepmeT;C°4taisp/O

motsuC

2N3N4N5N6N

erudecorpnoitaraperPP–)teksagEFTPdnalliftrenihtiwelbaliavaylno(gninaelcecivresnegyxO xam T;isp0471/rab021/aPM21= xam F°041/C°06=

noitaraperpecivresnegordyHnoitaraperpsecivreslaicepS

1P2P4P


15

Note 1: Suitable for oxygen service

Note 2: Not available with sensor code B

Note 3: Select type in additional ordering code

Note 4: Not available with Electronic Housing code Z, R, G and W

Note 5: Not available with Electronic Housing code P, E and K

Note 6: Not available with Process flanges/adapters code D, E, G, H, Q, T, M, S, U, V

Note 7: Not available with Process flanges/adapters code D, E, G, H, M, S, U, V

Note 8: Not available with Process flanges/adapters code A, B, G, H, Q, T, M, S, U, V

Note 9: Not available with Process flanges/adapters code A, B, G, H, Q, T, U, V

Note 10: Not available with Process flanges/adapters code A, B, D, E, Q, T, M, S, U, V

Note 11: Not available with Process flanges/adapters code A, B, D, E, Q, T, M, S

Note 12: Not available with PROFIBUS PA and FF output code 2 or 3

Note 13: Not available with Electronic housing code U, S, T, V, H, M, L, N, D, C, A, B, J, Y




Standard delivery items (can be differently specified by additional ordering code)– Adapters supplied loose

– Plug on axis of horizontal connection flange; nothing for vertical connection blind flange (no drain/vent valves)

– General purpose (no electrical certification)

– No meter/display, no mounting bracket, no surge protection

– English manual and labels

– Configuration with kPa and deg. C units

– No test, inspection or material traceability certificates

THE SELECTION OF SUITABLE WETTED PARTS AND FILLING FLUID FOR COMPATIBILITY WITH THE PROCESS MEDIA IS A CUSTOMER'SRESPONSIBILITY, IF NOT OTHERWISE NOTIFIED BEFORE MANUFACTURING.

SD462ledomrofNOITAMROFNIGNIREDROLANOITIDDA XX XX XX

setacifitreCnoitarbilacfoB.1.3–40201NEetacifitrecnoitcepsnI

ngisedtnemurtsnifo1.2–40201NEredroehthtiwecnailpmocfoetacifitreC1C6C

ytilibaecartlairetaMstrapdettewssecorpfo1.2–40201NEredroehthtiwecnailpmocfoetacifitreC

strapdettewssecorpfoB.1.3–40201NEetacifitrecnoitcepsnI1H3H

rotcennoC8/7subdleiF

1x21MsubdleiFyrtnethgiarts–NAHgnitraH

yrtneelgna–NAHgnitraH

)31,5setoN()31,5setoN()31,4setoN()31,4setoN(

1U2U3U4U


16

BASIC ORDERING INFORMATION model 264PS Gauge Pressure TransmitterSelect one character or set of characters from each category and specify complete catalog number.Refer to additional ordering information code and specify one or more codes for each transmitter if additional options are required.

LEDOMESAB 1– ts 5ot ht sretcarahc 2 6 4 P S X S X X X X X

%570.0YCARUCCAESAB–rettimsnarTerusserPeguaG

–stimilnapS-ROSNES 6 ht retcarahcaPk4dna431.0aPk61dna72.0

aPk04dna4.0aPk56dna56.0aPk061dna6.1

aPk006dna6aPk0042dna42aPk0008dna08

aPk00061dna061

rabm04dna43.1rabm061dna7.2

rabm004dna4rabm056dna5.6rabm0061dna61



Hni61dna45.0 2OHni46dna80.1 2OHni061dna6.1 2OHni062dna6.2 2OHni246dna4.6 2Oisp78dna78.0isp843dna5.3


BEFGHMPQS




™672CyolletsaH™004lenoM

mulatnaTssL613ISIA


™004lenoMmulatnaT


™672CyolletsaH

lioenociliSlioenociliSlioenociliSlioenociliSlioenociliS

diulftrenIdiulftrenIdiulftrenIdiulftrenIdiulftrenI


)2etoN(

)2etoN()2etoN(

)2,1setoN()2,1setoN()2,1setoN()2,1setoN()2,1setoN(

)2etoN(

ECANECANECANECAN

ECANECANECANECAN

ECANECAN

SHKMTABFCDLQP





AB



DE



GH




QT



MS



UV


ss613ISIAss613ISIA



)1etoN(EFTP

)1etoN(

)1etoN(ECANECAN

1234




5.31gP1/2 KGni




)ylnoesopruplareneg()3etoN()ylnoesopruplareneg()ylnoesopruplareneg(


ABDCEG



5.31gP1/2 KGni


HLNMPR



5.31gP1/2 KGni

rotcennocsubdleiF

STVUZ


)02MC(5.1x02M5.31gP


JYKW








)5,4setoN()4etoN(

)5,4setoN()5etoN(

)5,4setoN()5etoN(

H1P2F3


17

ADDITIONAL ORDERING INFORMATION for model 264PSAdd one or more 2-digit code(s) after the basic ordering information to select all required options









mottobedisegnalfno



1V2V3V4V5V6V7V8V9V





1E2E3E4E5E6E

retemtuptuO


elacs%001–0raenilrotacidnituptuogolanA)elacsraenilrofdeificepsebot(noitaudarglaiceps,rotacidnituptuogolanA


)21etoN()21etoN()21etoN()21etoN()21etoN()21etoN(

1D2D3D5D7D8D



xobrofepyttalF



1B2B3B4B5B



nailatI1M2M


nailatI1T2T



motsuC

2N3N4N5N6N



1P2P4P


18


Note 2: Not available with sensor code B






















THE SELECTION OF SUITABLE WETTED PARTS AND FILLING FLUID FOR COMPATIBILITY WITH THE PROCESSMEDIA IS A CUSTOMER'S RESPONSIBILITY, IF NOT OTHERWISE NOTIFIED BEFORE MANUFACTURING.

SP462ledomrofNOITAMROFNIGNIREDROLANOITIDDA XX XX XX

setacifitreC

noitarbilacfoB.1.3–40201NEetacifitrecnoitcepsnIngisedtnemurtsnifo1.2–40201NEredroehthtiwecnailpmocfoetacifitreC

1C6C

ytilibaecartlairetaM

strapdettewssecorpfo1.2–40201NEredroehthtiwecnailpmocfoetacifitreCstrapdettewssecorpfoB.1.3–40201NEetacifitrecnoitcepsnI

1H3H

rotcennoC

8/7subdleiF1x21MsubdleiF

yrtnethgiarts–NAHgnitraHyrtneelgna–NAHgnitraH


1U2U3U4U


19

BASIC ORDERING INFORMATION model 264VS Absolute Pressure TransmitterSelect one character or set of characters from each category and specify complete catalog number.Refer to additional ordering information code and specify one or more codes for each transmitter if additional options are required.

LEDOMESAB 1– ts 5ot ht sretcarahc 2 6 4 V S X S X X X X X

%570.0YCARUCCAESAB-rettimsnarTerusserPetulosbA

–stimilnapS–ROSNES retcarahcht6aPk61dna72.0

aPk04dna76.0aPk56dna1.1

aPk061dna76.2aPk006dna01

aPk0042dna04aPk0008dna431

aPk00061dna762

rabm061dna7.2rabm004dna7.6rabm056dna11

rabm0061dna7.62rab6dna1.0


rab061dna76.2

gHmm021dna2gHmm003dna5gHmm084dna8

gHmm0021dna02isp78dna54.1isp843dna8.5


EFGHMPQS




™672CyolletsaHssL613ISIA



™672CyolletsaH

lioenociliSlioenociliSlioenociliS

diulftrenIdiulftrenIdiulftrenI


)2,1setoN()2,1setoN()2,1setoN(

)2etoN()2etoN()2etoN(

ECANECAN

ECANECAN

ECANECAN

SHKABFLQP





AB



DE



GH




QT



MS



UV


ss613ISIAss613ISIA



EFTP

)1etoN(

)1etoN(ECANECAN

1234




5.31gP1/2 KGni



ABDCEG



5.31gP1/2 KGni



HLNMPR



5.31gP1/2 KGni

rotcennocsubdleiF )ylnoesopruplareneg()3etoN(

STVUZ


)02MC(5.1x02M5.31gP


)ylnoesopruplareneg()ylnoesopruplareneg(


JYKW








)5,4setoN()4etoN(

)5,4setoN()5etoN(

)5,4setoN()5etoN(

H1P2F3


20

ADDITIONAL ORDERING INFORMATION for model 264VSAdd one or more 2-digit code(s) after the basic ordering information to select all required options









mottobedisegnalfno



1V2V3V4V5V6V7V8V9V





1E2E3E4E5E6E

retemtuptuO


elacs%001–0raenilrotacidnituptuogolanA)elacsraenilrofdeificepsebot(noitaudarglaiceps,rotacidnituptuogolanA


)21etoN()21etoN()21etoN()21etoN()21etoN()21etoN(

1D2D3D5D7D8D



xobrofepyttalF



1B2B3B4B5B



nailatI1M2M


nailatI1T2T



motsuC

2N3N4N5N6N



1P2P4P


21


Note 2: Not available with sensor code E






















THE SELECTION OF SUITABLE WETTED PARTS AND FILLING FLUID FOR COMPATIBILITY WITH THE PROCESS MEDIA IS A CUSTOMER'SRESPONSIBILITY, IF NOT OTHERWISE NOTIFIED BEFORE MANUFACTURING.

SV462ledomrofNOITAMROFNIGNIREDROLANOITIDDA XX XX XX

setacifitreC

noitarbilacfoB.1.3–40201NEetacifitrecnoitcepsnIngisedtnemurtsnifo1.2–40201NEredroehthtiwecnailpmocfoetacifitreC

1C6C

ytilibaecartlairetaM

strapdettewssecorpfo1.2–40201NEredroehthtiwecnailpmocfoetacifitreCstrapdettewssecorpfoB.1.3–40201NEetacifitrecnoitcepsnI

1H3H

rotcennoC

8/7subdleiF1x21MsubdleiF

yrtnethgiarts–NAHgnitraHyrtneelgna–NAHgnitraH


1U2U3U4U


22


23


ABB LtdHoward Road, St. NeotsCambridgeshire, PE19 3EUUKTel: +44(0)1480 475321Fax: +44(0)1480 217948

ABB Inc.125 E. County Line RoadWarminster, PA 18974USATel: +1 215 674 6000Fax: +1 215 674 7183

ABB SACE spaBusiness Unit InstrumentationVia Statale 11322016 Lenno (CO) ItalyTel: +39 0344 58111Fax: +39 0344 56278

SS

/264

XS_1

ABB has Sales & Customer Supportexpertise in over 100 countries worldwide

www.abb.com

The Company’s policy is one of continuous productimprovement and the right is reserved to modify the

information contained herein without notice.

Printed in Italy (04.03)

© ABB 2002

ABB Automation Products GmbHSchillerstrasse 72D-32425 MindenGermanyTel: +49 (0) 571 830 1691Fax: +49 (0) 571 830 1368

ss/264xs 1 2600t series pressure transmitters · 2014-05-28 · data sheet ss/264xs_1 abb 2600t...

Documents