specifications for fpd module - codico · 7.5 display or permanent damage to display 7.6 optimal...

Preliminary The contents of this document are confidential and must not be disclosed wholly or in part to any third part without the prior written consent of AMPIRE CO., LTD

Date : 2015/03/18 AMPIRE CO., LTD. 1

SPECIFICATIONS FOR FPD MODULE

CUSTOMER

CUSTOMER PART NO.

AMPIRE PART NO. AE-7201280BOF-00

APPROVED BY

DATE

Approved For Specifications Approved For Specifications & Sample

APPROVED BY CHECKED BY ORGANIZED BY

AMPIRE CO., LTD. 2F., No.88, Sec. 1, Sintai 5th Rd., Sijhih City, Taipei County 221, Taiwan (R.O.C.)台北縣汐止市新台五路一段88號2樓(東方科學園區D棟)TEL:886-2-26967269 , FAX:886-2-26967196 or 26967270



RECORD OF REVISION

Revision Date Page Contents Editor

2015/03/18

-- New Release

Emil



1 Features

7.6 inch AMOLED (Active Matrix Organic Light-Emitting Diode) module. This module

is composed of a 5” AMOLED panel and power driver circuit.

1.1 AMOLED Feature :

(1) Construction: 5” AMOLED.

(2) Resolution (pixel): 720(R.G.B) X 1280

(3) Interface: MIPI 4 Lanes.

(4) Color: 16M colors

2 Physical specifications

Item Specifications Unit

Display resolution(dot) 720(R.G.B.) (W) x 1280(H) dots

Active area 62.1 (W) x 110.4 (H) mm

Encapsulation Glass outline 65.70 x 115.00 mm

Glass outline 65.70 x 118.40 mm

Pixel pitch 28.75 x 86.25 um

Diagonal size 5 inch

Glass thickness 0.3 / 0.3 mm

Color configuration R.G.B stripe

Weight TBD g

3 Maximum Rating

SPEC Parameter Symbol

Min. Typ. Max. Unit Note

Analog/boost power voltage VCI -0.3 5.28 V - VCI I/O voltage VCI_IF -0.3 5.28 V - I/O voltage VDDIO -0.3 3.96 V - VSP voltage VSP 6.5 V - VPP (OTP power) VPP 8.64 V - Operating temperature Top -20 60 ℃ Storage temperature Tstg -30 70 ℃



4 Electrical Specifications

4.1 Electrical Characteristics

4.1.1 Power Characteristic：

Item Symbol Min. Typ. Max. Unit Note AMOLED power positive ELVDD - 4.6 -- V Ref AMOLED power negative ELVSS - -3.5 V Ref OTP power VPP 7.4 7.6 7.8 V Ref Gamma voltage VSP - 6.5 V Ref Digital power supply VDDI 1.65 3.3 3.6 V Ref Analog power supply VCI 2.5 3.3 4.8 V Ref

Mode Symbol Condition Min. Typ. Max. Unit Note

IELVDD/ELVSS - 60 80 mA

IVCI - 15 mA Normal

IVPP

VELVDD=4.6V VELVSS=-3.5V

VCI=3.3V VSP=6.5V

@ Gray 128 - 20 mA

4.1.2 Power supply circuit application (This is for reference only )：



4.2 I/O Connection and Block Diagrams

4.2.1 I/O Connection No. Pin name I/O Description 1

vpp Power Power supply for OTP.

Leave the pin to open when not in use. 2 ID_1 - No connection. 3 ID_2 - No connection. 4

RESX I This signal will reset the device and must be applied to

properly initialize the chip. Active low. 5 GND Power The power ground. 6 D2P I MIPI DSI data 2+. 7 D2N I MIPI DSI data 2+. 8 GND Power The power ground. 9 D1P I MIPI DSI data 1+.

10 D1N I MIPI DSI data 1+. 11 GND Power The power ground. 12 CKP I MIPI DSI clock+. 13 CKN I MIPI DSI clock+. 14 GND Power The power ground. 15 D0P I MIPI DSI data 0+. 16 D0N I MIPI DSI data 0+. 17 GND Power The power ground. 18 D3P I MIPI DSI data 3+. 19 D3N I MIPI DSI data 3+. 20 GND Power The power ground. 21 TE O Tear effect output. 22 VCI Power Driver IC analog supply. 23 VDDI Power Driver IC digital I/O supply. 24 SWIRE O Power IC control pin. 25 OLED_EN O Power IC enable. 26 ELVDD Power AMOLED power Positive. 27 ELVDD Power AMOLED power Positive. 28 ELVSS Power AMOLED power Negative. 29 ELVSS Power AMOLED power Negative. 30 VSP Power PFM's Voltage. 31 VSP Power PFM's Voltage.



4.2.2 Display Module Block Diagram

4.3 Recommended Operating Sequence

4.3.1 Power on sequence

4.3.2 Power off sequence



4.4 AC Characteristics（MIPI）

4.4.1 HS Data Transmission Burst

4.4.2 HS Clock Transmission

4.4.3 Turnaround Procedure

4.4.4 Timing Parameters



5 Electro-Optical Specification



6 RELIABILITY TEST CONDITIONS

ITEM CONDITIONS

HIGH TEMPERATURE OPERATION 70℃ , 24Hrs

HIGH TEMPERATURE AND HIGH HUMIDITY OPERATION

60℃ , 90%RH , 96Hrs

LOW TEMPERATURE OPERATION -20℃ , 24Hrs

THERMAL SHOCK STORAGE -40℃ ~ 85 ℃ 30min,change

time ＜5min,30 cycles



7 Handling Precautions

7.1 When cleaning ITO pad, avoid using hard and abrasive material or corrosive solution.

7.2 Keep module away from direct sunlight or fluorescent light, and keep it at room

temperature and humidity.

7.3 Strong impact & pressure on module and packing is prohibited.

7.4 Following normal power on/off sequence is necessary for preventing abnormal.

7.5 Display or permanent damage to display

7.6 Optimal contrast ratio under ideal voltage is AMOLED module’s characteristic, hence it

is recommended a voltage control function available.

7.7 Image sticking may occur if an image displays for an extended period of time.

7.8 When interfered by system’s overall mechanical design, an abnormal display may occur

After considering emitting energy, you should plan your design to satisfy EMI standards.

7.9 Host side should place a surge-prevent circuit at power trace (ie: VCI, Vddi) to protect

AMOLED module.



7 OUTLINE DIMENSION

specifications for fpd module - codico · 7.5 display or permanent damage to display 7.6 optimal...

Documents