specification sheet abb welcome™ lift (elevator) adaptor

2
SPECIFICATION SHEET ABB Welcome™ Lift (elevator) adaptor and control relay module Key features Turn the 2-bus line signal into RS485 signal Can be directly connected to PC for configuration using ABB Welcome configuration software Two operating lights: POWER and RUN STATUS The lift adaptor and control relay modules are used together to provide elevator control. Residents can control guest floor access by activating the elevator upon arrival home. When installed and commissioned properly, up to 256 floors can be supported. Operating temperature -13 F to 131 F Ingress protection IP20 Single-wire clamps 2 x 22AWG – 2 x 16AWG Fine-wire clamps 2 x 22AWG – 2 x 16AW Bus voltage 20-30 VDC (Provided by M2301 configured as a local power supply) Product dimensions 3.54" x 2.83" x 2.56" Specifications 01 M2306 lift adaptor

Upload: others

Post on 09-Jan-2022

9 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: SPECIFICATION SHEET ABB Welcome™ Lift (elevator) adaptor

—S PECI FI C ATI O N S H EE T

ABB Welcome™Lift (elevator) adaptor and control relay module

Key features• Turn the 2-bus line signal into RS485 signal• Can be directly connected to PC for configuration

using ABB Welcome configuration software• Two operating lights: POWER and RUN STATUS

The lift adaptor and control relay modules are used together to provide elevator control. Residents can control guest floor access by activating the elevator upon arrival home. When installed and commissioned properly, up to 256 floors can be supported.

Operating temperature -13 F to 131 F

Ingress protection IP20

Single-wire clamps 2 x 22AWG – 2 x 16AWG

Fine-wire clamps 2 x 22AWG – 2 x 16AW

Bus voltage 20-30 VDC (Provided by M2301 configured as a local power supply)

Product dimensions 3.54" x 2.83" x 2.56"

—Specifications

—01 M2306 lift adaptor

Page 2: SPECIFICATION SHEET ABB Welcome™ Lift (elevator) adaptor

Key features• Turn the RS485 signal into relay switch• Each module contains 16 relays• The relay can connect elevator button panel directly• Can set a relay for a floor number

Operating temperature -13 F to 131 F

Ingress protection IP20

Single-wire clamps 2 x 22AWG – 2 x 16AWG

Fine-wire clamps 2 x 22AWG – 2 x 16AWG

Bus voltage 20-30 VDC (Provided by M2301 configured as a local power supply)

Product dimensions 8.50" x 4.33" x 1.77"

—Specifications

—02 M2307 lift control relay module

1SX

U4

60

028

L0

201

Rev

.B M

arch

20

21

—We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB Inc. does not accept any responsibility whatsoever for potential errors or possible lack of information in this document.

We reserve all rights in this document and in the subject matter and illustrations contained therein. Any reproduction, disclosure to third parties or utilization of its contents – in whole or in parts – is forbidden without prior written consent of ABB Inc. © 2021 ABB All rights reserved.

—ABB Inc.Electrification Products860 Ridge Lake BoulevardMemphis, TN 38120 www.abb.com/door-entry-system-us

electrification.us.abb.com

—USA Technical Support: 888-862-32897:00 a.m. to 5:00 p.m., CST, Monday - [email protected]

USA Technical Support: 888-862-32897:00 a.m. to 5:00 p.m., CST, Monday - [email protected]