Spare parts list

Part No.: R902063242

Drawing no.: R902026540

Designation: A4VG71DWDMT1/32R-NSF02F001D-S

Status of version: 11/2014 Date: 18.02.2015

Page: 1

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R909607770 ROTARY GROUP

AA4V-71

1 ST L

2 R902044417 CONTROL, HYDRAULIC 1 ST L

3 R902026537 PORT PLATE WITH VALVES 1 ST L

4 R909606657 INTERNAL GEAR PUMP ASSEMBLY 1 ST L

5 R902007023 CONTROL MODULE

DWDN71MS12

1 ST L

10 R902003862 HOUSING

METR. 25218.2000

1 ST

13 R902132711 JOINT PIN

25225.0000

2 ST

20 R909153891 LOCKING SCREW

ZN10001-M26X1,5-N-ST

1 ST D

21 R909151979 LOCKING SCREW

ZN10001-M14X1,5-N-ST

1 ST D

Spare parts list

Part No.: R902063242

Drawing no.: R902026540

Designation: A4VG71DWDMT1/32R-NSF02F001D-S

Status of version: 11/2014 Date: 18.02.2015

Page: 2

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

22 R909151692 LOCKING SCREW

ZN10001-M12X1,5-N-ST

4 ST D

24 R909083228 LOCKING SCREW

N02.017-M33X2-5.8-PHR

1 ST D

25 R909086731 O-RING

29,82 X 2,62-S-NBR90&

1 ST D

26 R909153572 LOCKING SCREW

N02.020-M8X1-5.8-ZNPH

1 ST D

27 R909831318 DOUBLE BREAK-OFF PLUG

ZN10006-M6

1 ST D

28 R909156494 ORIFICE

RNM02105-M6-1,2

2 ST D

31 R909156579 CLAMPING PIN

DIN7344-3X10

2 ST D

32 R909153364 LOCKING SCREW

ZN10001-M10X1-N-ST

2 ST D

Spare parts list

Part No.: R902063242

Drawing no.: R902026540

Designation: A4VG71DWDMT1/32R-NSF02F001D-S

Status of version: 11/2014 Date: 18.02.2015

Page: 3

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

33 R909151694 LOCKING SCREW

ZN10001-M22X1,5-N-ST

2 ST D

37 R909087913 LOCKING SCREW

N02.020-M18X1,5-5.8-&

1 ST D

46 R909436131 ECCENTRIC SCREW

24418.0000

1 ST

47 R909087405 SEALING NUT

N02.100-M12X1,5

1 ST D

48 R909153815 LOCKING SCREW

ZN10001-M18X1,5-N-ST

1 ST D

49 R909831347 PLUG

RNM02105-M6

1 ST D

Spare parts list

Part No.: R902063242

Drawing no.: R902026540

Designation: A4VG71DWDMT1/32R-NSF02F001D-S

Status of version: 11/2014 Date: 18.02.2015

Page: 4

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Spare parts list

Part No.: R909607770

Drawing no.: R902079243

Designation: ROTARY GROUP

AA4V-71

Status of version: 11/2014 Date: 18.02.2015

Page: 5

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R902079247 ROTARY GROUP, HYDR. SECTION

HYDR. TEIL

1 ST L

2 R902007628 CONTROL PLATE, RIGHT-HAND ROT.

'5 GRAD' '

1 ST

12 R909443361 CRADLE

'R'

1 ST

13 R909449810 SLIDE RING

21520.2102

1 ST

14 R909921936 DRIVE SHAFT

21518.2123

1 ST

17 R909076233 WIRE

23025.0303

2 ST

26 R902066586 BEARING LINER (PAIR)

101X108X15

1 ST

Spare parts list

Part No.: R909607770

Drawing no.: R902079243

Designation: ROTARY GROUP

AA4V-71

Status of version: 11/2014 Date: 18.02.2015

Page: 6

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

31 R909153104 PLAIN ROLLER BEARING

NUP40X80X23

1 ST

32 R909830152 CRADLE BEARING ASSEMBLY ( SET)

85X101X22 &

1 ST

36 R909083362 RETAINING RING

DIN471-40X1,75

1 ST

37 R902600001 RETAINING RING

DIN 984-80X2,5

2 ST

38 R902601794 SHAFT SEAL RING

BABSL10FX245X80X7-F &

1 ST D

98 R902002389 SEAL KIT DRIVE SHAFT

TRIEBWELLE A4VG71/32

1 ST

Spare parts list

Part No.: R909607770

Drawing no.: R902079243

Designation: ROTARY GROUP

AA4V-71

Status of version: 11/2014 Date: 18.02.2015

Page: 7

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Spare parts list

Part No.: R902079247

Drawing no.: R902079250

Designation: ROTARY GROUP, HYDR. SECTION

HYDR. TEIL

Status of version: 11/2014 Date: 18.02.2015

Page: 8

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R909443972 CYLINDER WITH BUSHING

M. BUCHSEN

1 ST

2 R909416736 PISTON-SLIPPER PAD 9 ST

11 R902192957 CUP-SPRING STACK

21518.2121

1 ST

20 R909432987 SHIM

'1,20' 21518.2101

1 ST

20 R909432988 SHIM

'1,00' 21518.2101

1 ST

20 R909432989 SHIM

'0,80' 21518.2101

1 ST

20 R909432990 SHIM

'0,60' 21518.2101

1 ST

Spare parts list

Part No.: R902079247

Drawing no.: R902079250

Designation: ROTARY GROUP, HYDR. SECTION

HYDR. TEIL

Status of version: 11/2014 Date: 18.02.2015

Page: 9

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

24 R902205454 RETAINING PLATE

'R' ASIA 21518.2121

1 ST

25 R909921905 RETAINING BALL 1 ST

27 R909921903 WASHER

21518.2121

2 ST

29 R909435254 PRESSURE SPRING

'6,00/ 37,00/ 39,29'

1 ST

41 R909083403 RETAINING RING

DIN472-45X1,75

1 ST

Spare parts list

Part No.: R902079247

Drawing no.: R902079250

Designation: ROTARY GROUP, HYDR. SECTION

HYDR. TEIL

Status of version: 11/2014 Date: 18.02.2015

Page: 10

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Spare parts list

Part No.: R902044417

Drawing no.: R902020316

Designation: CONTROL, HYDRAULIC

Status of version: 11/2014 Date: 18.02.2015

Page: 11

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R902031411 POSITIONING PISTON COMPLETE

T 7-18,4BAR

1 ST L

3 R902015607 COVER

45218.7236

1 ST

4 R902015608 COVER

45218.7236

1 ST

16 R909154918 HEXAGON NUT

N02.018-B-M12X1,5-04&

1 ST

17 R909084744 SOCKET-HEAD SCREW

DIN912-M6X20-10.9

8 ST

20 R909084482 O-RING

N 02.079- 69,52 X 2,62-S-NBR70

2 ST D

21 R909430349 THREADED PIN

45218.3215

2 ST

22 R909153271 SEALING NUT

N02.100-M10X1

2 ST D

Spare parts list

Part No.: R902044417

Drawing no.: R902020316

Designation: CONTROL, HYDRAULIC

Status of version: 11/2014 Date: 18.02.2015

Page: 12

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

30 R902600837 GUIDE RING

RING 67X72X9,5-C380

2 ST D

31 R902600196 ROD SEAL

67X77,7X 4,1-074

2 ST D

98 R902002372 SEAL KIT HYDR. CONTROL

VERSTELLUNG A4VG71/32

1 ST

Spare parts list

Part No.: R902044417

Drawing no.: R902020316

Designation: CONTROL, HYDRAULIC

Status of version: 11/2014 Date: 18.02.2015

Page: 13

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Spare parts list

Part No.: R902031411

Drawing no.: R902020319

Designation: POSITIONING PISTON COMPLETE

T 7-18,4BAR

Status of version: 11/2014 Date: 18.02.2015

Page: 14

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R902210163 POSITIONING PISTON

45218.0000

1 ST

2 R909449239 ROD

45218.3213

1 ST

5 R902015508 RING

'5,77' 42517.7211

2 ST

5 R902013493 RING

'5,82' 45217.7211

2 ST

5 R902015509 RING

'5,87' 45217.7211

2 ST

5 R902015510 RING

'5,92' 45217.7211

2 ST

5 R902015511 RING

'5,97' 45217.7211

2 ST

Spare parts list

Part No.: R902031411

Drawing no.: R902020319

Designation: POSITIONING PISTON COMPLETE

T 7-18,4BAR

Status of version: 11/2014 Date: 18.02.2015

Page: 15

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

5 R902015512 RING

'6,02' 45217.7211

2 ST

5 R902015514 RING

'5,67' 45217.7211

2 ST

5 R902015513 RING

'5,72' 45217.7211

2 ST

6 R902600489 ASSEMBLY RING

16 Z.-NR.11.44637 &

2 ST

7 R902020101 SPRING COLLAR

45218.6213

2 ST

9 R902029699 PRESSURE SPRING

' 6,50/ 30,90/ 69,61'

2 ST

10 R909432898 PRESSURE SPRING

'5,00/ 46,00/ 32,20'

2 ST

15 R909084557 RETAINING RING

DIN 472- 58X2

2 ST

Spare parts list

Part No.: R902031411

Drawing no.: R902020319

Designation: POSITIONING PISTON COMPLETE

T 7-18,4BAR

Status of version: 11/2014 Date: 18.02.2015

Page: 16

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

19 R909083728 O-RING

N 02.079- 9,25 X 1,78-S-NBR70

1 ST D

23 R909449248 SPRING COLLAR

45218.3213

2 ST

26 R909432885 PRESSURE SPRING

' 3,60/ 18,40/ 45,80'

2 ST

Spare parts list

Part No.: R902031411

Drawing no.: R902020319

Designation: POSITIONING PISTON COMPLETE

T 7-18,4BAR

Status of version: 11/2014 Date: 18.02.2015

Page: 17

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Spare parts list

Part No.: R902026537

Drawing no.: R902154293

Designation: PORT PLATE WITH VALVES

Status of version: 11/2014 Date: 18.02.2015

Page: 18

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R902603814 PRESSURE RELIEF VALVE

R901162655

2 ST L

2 R909434856 PRESSURE RELIEF VALVE

ND 15-35BAR #70NM

1 ST L

3 R909608507 PRESSURE OVERRIDE VALVE

A4VG71/31+32 'SO' #35NM

1 ST L

5 R902154169 PORT PLATE

A4VG71/32 SERIE

1 ST

6 R909449136 BEARING BUSHING

29618.5000

1 ST

7 R909083141 SOCKET-HEAD SCREW

DIN912-M16X90-10.9

4 ST

9 R909085947 O-RING

N 02.079-113,97 X 2,62-S-NBR70

1 ST D

11 R909831318 DOUBLE BREAK-OFF PLUG

ZN10006-M6

2 ST D

Spare parts list

Part No.: R902026537

Drawing no.: R902154293

Designation: PORT PLATE WITH VALVES

Status of version: 11/2014 Date: 18.02.2015

Page: 19

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

12 R909153364 LOCKING SCREW

ZN10001-M10X1-N-ST

1 ST D

13 R909831319 DOUBLE BREAK-OFF PLUG

ZN10006-M8

2 ST D

26 R909085709 O-RING

9,25X1,78-S-NBR90 &

2 ST D

35 R909151692 LOCKING SCREW

ZN10001-M12X1,5-N-ST

2 ST D

43 R909444842 BUSH

23118.2000

1 ST

44 R909426654 BEARING BUSHING

23118.2000

1 ST

47 R909086333 O-RING

N 02.079- 12,42 X 1,78-S-NBR90

2 ST D

98 R902002399 SEAL KIT PORT PLATE WITH VALVES

ANSCHL.PL. A4VG71/32

1 ST

Spare parts list

Part No.: R902026537

Drawing no.: R902154293

Designation: PORT PLATE WITH VALVES

Status of version: 11/2014 Date: 18.02.2015

Page: 20

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Spare parts list

Part No.: R902603814

Designation: PRESSURE RELIEF VALVE

R901162655

Status of version: 11/2014 Date: 18.02.2015

Page: 21

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R901162655 PRESSURE RELIEF VALVE

22 K2-3X/520VHP-130

1 ST

98 R961003396 SEAL KIT

MH-R/HP/V (2-FACH)

1 ST D

Spare parts list

Part No.: R909434856

Drawing no.: R909730913

Designation: PRESSURE RELIEF VALVE

ND 15-35BAR #70NM

Status of version: 11/2014 Date: 18.02.2015

Page: 22

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R909436167 LOCKING SCREW

52115.1011

1 ST

2 R909449622 ADJUSTING SCREW

52115.1011

1 ST

3 R909435899 VALVE PISTON

52112.1010

1 ST

4 R902010336 SPRING COLLAR

52112.1011

1 ST

5 R909440765 PRESSURE SPRING

'2,50/ 13,00/ 35,00'

1 ST

8 R909083761 O-RING

23,47X2,62-S-NBR90&

1 ST D

9 R902197111 SEALING NUT

M10X1 'ID.R909153271' #30NM&

1 ST D

Spare parts list

Part No.: R909434856

Drawing no.: R909730913

Designation: PRESSURE RELIEF VALVE

ND 15-35BAR #70NM

Status of version: 11/2014 Date: 18.02.2015

Page: 23

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

98 R902166399 DICHTUNGSSATZ DRUCKBEGR.VENTIL ND

DRUCKBEGR.

1 ST

Spare parts list

Part No.: R909434856

Drawing no.: R909730913

Designation: PRESSURE RELIEF VALVE

ND 15-35BAR #70NM

Status of version: 11/2014 Date: 18.02.2015

Page: 24

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Spare parts list

Part No.: R909608507

Drawing no.: R909731050

Designation: PRESSURE OVERRIDE VALVE

A4VG71/31+32 'SO' #35NM

Status of version: 11/2014 Date: 18.02.2015

Page: 25

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R909432161 LOCKING SCREW

52508.0403

1 ST

2 R909425951 VALVE BUSHING

52508.0400

1 ST

3 R909921369 CONTROL PISTON

52508.0411

1 ST

4 R909432163 PISTON

52508.0403

1 ST

5 R909432164 VALVE PISTON

52508.0403

1 ST

6 R909436284 POPPET SEAT

52508.0407

1 ST

7 R902168277 PRESSURE SPRING

'1,80/ 7,30/ 24,85'

1 ST

Spare parts list

Part No.: R909608507

Drawing no.: R909731050

Designation: PRESSURE OVERRIDE VALVE

A4VG71/31+32 'SO' #35NM

Status of version: 11/2014 Date: 18.02.2015

Page: 26

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

8 R902049851 SPRING COLLAR

52508.0424

2 ST

9 R909432167 ADJUSTING SCREW

52508.0403

1 ST

10 R909083752 O-RING

N 02.079- 12,37 X 2,62-S-NBR90

1 ST D

14 R909152707 SEALING NUT

N02.100-M8

1 ST D

15 R909086380 O-RING

N 02.079- 6,07 X 1,78-S-NBR90

1 ST D

Spare parts list

Part No.: R909608507

Drawing no.: R909731050

Designation: PRESSURE OVERRIDE VALVE

A4VG71/31+32 'SO' #35NM

Status of version: 11/2014 Date: 18.02.2015

Page: 27

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Spare parts list

Part No.: R909606657

Drawing no.: R902077732

Designation: INTERNAL GEAR PUMP ASSEMBLY

Status of version: 11/2014 Date: 18.02.2015

Page: 28

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R902079038 INTERNAL GEAR PUMP

O.V.

1 ST L

2 R902077978 WEAR PLATE COMPLETE

KP

1 ST L

3 R913007069 LOCKING PLUG

11.12801

2 ST

98 R902002411 SEAL KIT INTERNAL GEAR PUMP

IZP A4VG71/32

1 ST

Spare parts list

Part No.: R909606657

Drawing no.: R902077732

Designation: INTERNAL GEAR PUMP ASSEMBLY

Status of version: 11/2014 Date: 18.02.2015

Page: 29

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Spare parts list

Part No.: R902079038

Drawing no.: R909723594

Designation: INTERNAL GEAR PUMP

O.V.

Status of version: 11/2014 Date: 18.02.2015

Page: 30

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R902077943 PUMP COVER

29618.5000

1 ST

2 R909449136 BEARING BUSHING

29618.5000

1 ST

3 R909650382 STUB SHAFT

29618.5000

1 ST

5 R902006258 WHEEL SET

29618.7000

1 ST

6 R902025649 SHAFT KEY

29617.5000

1 ST

7 R909156930 SNAP RING

DIN7993-A38

1 ST

8 R909083060 SOCKET-HEAD SCREW

DIN912-M10X25-8.8

4 ST

Spare parts list

Part No.: R902079038

Drawing no.: R909723594

Designation: INTERNAL GEAR PUMP

O.V.

Status of version: 11/2014 Date: 18.02.2015

Page: 31

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

9 R909086679 O-RING

N 02.079- 88,57 X 2,62-S-NBR70

1 ST D

Spare parts list

Part No.: R902079038

Drawing no.: R909723594

Designation: INTERNAL GEAR PUMP

O.V.

Status of version: 11/2014 Date: 18.02.2015

Page: 32

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Spare parts list

Part No.: R902077978

Drawing no.: R902090839

Designation: WEAR PLATE COMPLETE

KP

Status of version: 11/2014 Date: 18.02.2015

Page: 33

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R902077959 WEAR PLATE

29618.7000&

1 ST

3 R909086679 O-RING

N 02.079- 88,57 X 2,62-S-NBR70

1 ST D

Spare parts list

Part No.: R902077978

Drawing no.: R902090839

Designation: WEAR PLATE COMPLETE

KP

Status of version: 11/2014 Date: 18.02.2015

Page: 34

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Spare parts list

Part No.: R902007023

Drawing no.: R902007027

Designation: CONTROL MODULE

DWDN71MS12

Status of version: 11/2014 Date: 18.02.2015

Page: 35

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R902228618 HOUSING 1 ST

2 R902005872 VALVE BUSHING

42915.0100

2 ST

3 R902007396 THROTTLE PISTON

'100' 42915.0100

2 ST

3 R902005870 THROTTLE PISTON

'80' 42915.0100

1 ST

3 R902005871 THROTTLE PISTON

'135' 42915.0100

1 ST

4 R909443061 VALVE HOUSING

42718.3133

1 ST

5 R909443060 VALVE PIN

42718.3133

1 ST

Spare parts list

Part No.: R902007023

Drawing no.: R902007027

Designation: CONTROL MODULE

DWDN71MS12

Status of version: 11/2014 Date: 18.02.2015

Page: 36

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

6 R902005869 VALVE HOUSING

42915.0100

1 ST

7 R902603829 GASKET

60X41 X-2-BOHR.7,1-F&

1 ST D

10 R909831957 CHECK VALVE

RVA 6 #15NM&

2 ST

11 R909085709 O-RING

9,25X1,78-S-NBR90 &

1 ST D

12 R909085701 SOCKET-HEAD SCREW

DIN912-M6X80-8.8

1 ST D

13 R909085831 SOCKET-HEAD SCREW

DIN912-M6X65-8.8

4 ST D

14 R902228591 PRESSURE SPRING

'1,40/ 6,

2 ST

15 R909831318 DOUBLE BREAK-OFF PLUG

ZN10006-M6

9 ST D

Spare parts list

Part No.: R902007023

Drawing no.: R902007027

Designation: CONTROL MODULE

DWDN71MS12

Status of version: 11/2014 Date: 18.02.2015

Page: 37

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

16 R909083493 THREADED PIN

N02.033-M8X8-10.9

1 ST

17 R902007176 THROTTLE VALVE

1.2 53108.0000

2 ST L

18 R909153815 LOCKING SCREW

ZN10001-M18X1,5-N-ST

4 ST D

19 R909151692 LOCKING SCREW

ZN10001-M12X1,5-N-ST

1 ST D

Spare parts list

Part No.: R902007023

Drawing no.: R902007027

Designation: CONTROL MODULE

DWDN71MS12

Status of version: 11/2014 Date: 18.02.2015

Page: 38

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Spare parts list

Part No.: R902007176

Drawing no.: R902007177

Designation: THROTTLE VALVE

1.2 53108.0000

Status of version: 11/2014 Date: 18.02.2015

Page: 39

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element

Pos. Part No. Designation Quantity

1 R902007175 VALVE SCREW

53108.0000

1 ST

2 R902007171 THREADED PIN

53108.0000

1 ST

3 R902007169 THROTTLE PIN

53108.0000

1 ST

Spare parts list

Part No.: R902007176

Drawing no.: R902007177

Designation: THROTTLE VALVE

1.2 53108.0000

Status of version: 11/2014 Date: 18.02.2015

Page: 40

Bosch Rexroth AG

Service Hydraulics

Glockeraustrasse 4

89275 Elchingen

Germany

+49 (0)7308/82-2126

Firmensitz / Headquarters: Stuttgart, Registrierung / Registration: Amtsgericht Stuttgart HRB 23192

Vorstand / Executive Board: Dr. Karl Tragl (Vorsitzender / President), Dr. Rolf-Dieter Amann; Dr. Bertram Hoffmann; Dr. Stefan Spindler

Vorsitzender des Aufsichtsrats / Chairman of the Supervisory Board: Dr. Werner Struth

Assembly, commissioning and operation, disassembly, service (including maintenance and repair) require basicmechanical/electrical/hydraulic/pneumatic knowledge, as well as knowledge of the appropriate technical terms. Inorder to ensure operating safety, these activities may therefore only be carried out by qualified technical personnelor an instructed person under the direction and supervision of qualified personnel. Qualified personnel are thosewho can recognize possible hazards and institute the appropriate safety measures due to their professionaltraining, knowledge, and experience, as well as their understanding of the relevant conditions pertaining to the workto be done. Qualified personnel must observe the rules relevant to the subject area. Also observe the generallyapplicable, legal or otherwise binding regulations of the European or national legislation and the rules for theprevention of accidents and for environmental protection applicable in your country. The data specified above onlyserve to describe the product. No statements concerning a certain condition or suitability for a certain applicationcan be derived from our information. The given information does not release the user from the obligation of ownjudgement and verification. It must be remembered that our products are subject to a natural process of wear andaging.©This document, as well as the data, specifications and other information set forth in it, are the exclusive propertyof Bosch Rexroth AG. Without their consent it may not be reproduced or given to third parties.

Security notice

L = Assembly group D = Sealing element