sound management barriers - imetcoimetco.com/.../2015/02/waveblok-brochure-2016-web.pdf · waveblok...
TRANSCRIPT
S O U N D M A N A G E M E N T B A R R I E R S
50%Over 50% of the installations of acoustical treatments are done after build completion, once noise has become an intolerable issue.
Most workplace environments should have quiet havens—places where private conversations can occur without being heard in adjacent rooms or passageways.
Excessive noise, and its effect on rest, are high on the list of complaints made by patients on post-discharge patient satisfaction surveys.
Good acoustics for learning support easy verbal communication, which requires low noise levels and very little reverberation.
Why address acoustics?
What is STC?
Sound Transmission ClassA numerical rating of how well a building partition attenuates airborne sound through walls, ceilings/floors, doors, windows and exterior wall configurations.Derived from standard frequencies tested from 125 Hz to 4000 Hz.
STC Rating Description Performance
15-25 Normal Speech Easily Understood Poor
25-35 Loud Speech Easily Understood Marginal
35-45 Half of Loud Speech Understood / Normal Speech Heard Good
45-55 Loud Speech Faintly Heard, Not Understood Very Good
55+ Loud Speech Usually Not Heard Excellent
2
Source: National Institute of Building Sciences
The WaveBlok™ family of products was designed to
provide high level STC and IIC ratings with low cost,
simple installation and high performance.
Consider WaveBlok for:
SOUND MANAGEMENT BARRIERS
Educational Facilities
Office Buildings
Medical Facilities
Multi-Unit Residential
Home Theater Rooms
Music Rooms
Recording Studios
Anywhere NOISE is a problem
WaveBlok™ SW
WaveBlok SW (Sub-Wall) is a highly engineered and unique sound reduction material. Wave-Blok SW is a mass loaded, flex-ible barrier designed for commer-cial, industrial, and residential applications to reduce sound transmission. It is used behind fin-ished wall or ceiling surfaces to block and reduce noise through the entire sound spectrum.
WaveBlok™ FC
WaveBlok FC (Floor/Ceiling) is a highly engineered damping composite designed to be placed onto the bare floor surface to sig-nificantly reduce noise between floors. Easily installs under all flooring including hardwood, carpet, laminate, tile and gypsum concrete.
WaveBlok™ RF
WaveBlok RF (Retro-Fit) is a unique noise reducing barrier created to go on the outside of existing walls. Easily installed, the finished surface is ready to paint.
3
Reduce Noise Levels up to 75%
BlokWave SW
4
Frequency 125 250 500 1000 2000 4000 STC Test NumberBaseline Wood Studs 21 31 39 51 38 50 34 NRC, IRC-IR-693
WaveBlok SW 1-Side, 16” OC 17 35 42 50 47 57 41 RAL-TL08-138
Baseline Metal Studs 22 42 56 62 48 50 44 RAL-TL08-183
WaveBlok SW 1-Side, 16” OC 28 42 55 60 58 61 53 RAL-TL08-184
WaveBlok SW 1-Side, 24” OC 34 45 56 60 57 62 56 RAL-TL08-152
WaveBlok SW 2-Sides, 24” OC 42 53 60 64 64 70 62 RAL-TL08-155
Product Performance
Minimum STC 25 per ASTM E 90-02 or SAE j1400
Flammability Rating of Class 1 per ASTM E 84 Rev. A (behind minimum 3/8” gypsum)
No Fungal/Algae Growth & No Visible Disfigurement per ASTM D3273 and ASTM G 21
Thermal Resistance Minimum of 0.3 per ASTM C 518 5
Meets 1 Hr. Fire Resistance Wall Rating per ASTM E 119 - 08
SuperiorSoundManagement
Made from a highly engineered recycled acoustical grade polymer.
Used behind finished wall & ceiling surfaces.
SUB WALLProduct Specifications
Standard Size4’ by 25’ roll (20 per Pallet)
Custom Sizes Available
Sheet Weight1.0 lb./ft2 nominal
Flexible: Easy to cut and install
Thin: Less than 1/8” thick
Class A fire and smoke rated
Mold and mildew resistant
Contains NO PVC
BlokWave FC
Assembly IIC STCCeramic tile over WaveBlok FC on 6” concrete non-isolated slab 51 46Ceramic tile over WaveBlok FC on wood joist with 1.5” thick gypsum concrete topping 55 501/2” Engineered hardwood over WaveBlok FC on 6” concrete non-isolated slab 47 461/2” Engineered hardwood over WaveBlok FC on wood joist with 1.5” thick gypsum concrete 55 548” Concrete slab with an insulated acoustical drop ceiling below & laminate hardwood flooring on top 58 58Ceramic tile over WaveBlok FC on 6” concrete non-isolated slab with drop ceiling 57
5
Product Performance
Flammability Rating of Class 1 per ASTM E 84 (when placed beneath a Class 1 Rated Floor)
No Fungal/Algae Growth & No Visible Disfigurement per ASTM D3273 and ASTM G 21
Significantly Reduces NoiseBetween Floors
Designed for Floor &
Ceiling
Easily installs under all types of flooring.
FLOOR & CEILINGProduct Specifications
Standard Size4’ by 25’ roll (16 per Pallet)
Custom Sizes Available
Sheet Weight0.75 lb./ft2 nominal
Flexible: easy to cut and install
Class A fire and smoke rated
Mold and Mildew resistant
Frequency
100
125
160
20
0
25
0
315
40
0
50
0
63
0
80
0
100
0
125
0
160
0
20
00
25
00
3150
40
00
50
00
Baseline (STC = 34) 19 19 15 17 22 28 28 32 37 39 41 43 40 35 36 41 47 52
w/ WaveBlok RF (STC = 39) 23 18 18 16 21 27 32 36 37 42 44 45 48 46 42 43 48 53
Designed to Address NoiseNOW
6
BlokWave RF
Product Performance
Passes ASTM E84 Fire and Smoke TestsFlame Spread = 5 (Class A)
Smoke Developed Index = 5 (Class A)Test # T-12435 (hpva)
Wood Studs 2” x 4”, 16” OC, Standard Drywall 5/8”Bare (no treatment) STC = 34 • w/ WaveBlok RF STC = 39Approximately 8 dB reduction in noise above 200Hz
Unique noise reducing barrier created to go on the outside
of existing walls.
Finished surface is ready to paint.
RETRO FITProduct Specifications
Made from Post-Industrial Recycled Materials
Standard Size4’ by 10’ sheets (50 per Pallet)
Custom Sizes Available
Sheet Weight0.75 lb./ft2 nominal (30 lbs. per Sheet)
Lightweight: Easy to install sheets
Performs as moisture barrier
Class A fire and smoke rated
Contains NO PVC
7
SustainabilityThe WaveBlok family of sound control products was designed using repro-cessed materials that would ordinarily be dumped in a land fill.
All of our WaveBlok products, at end of use, are completely recyclable. If a local recycler is not capable of pro-cessing the materials, they may be re-turned to IMETCO for reprocessing.
They will be processed into “like” products and returned once again into viable sound control solutions!
IMETCO is a leading manufacturer of premier metal products for the building envelope, delivering performance-inspired systems tailored to every project. IMETCO offers a full range of high-performance metal roofing, wall, and edge systems and accessories that provide a virtually limitless realm of aesthetic possibilities.
Driven by a collective desire to provide exceptional service at every opportunity, IMETCO pledges to communicate, promise and deliver innovative solutions, dedicated support, professional engineering services, and products manufactured to the highest quality standards.
© 2016 Innovative Metals Company, Inc.
(800) 646-3826 www.imetco.com
Scan the QR code for more information about WaveBlok Sound Management Barriers
a subsidiary of Garland Industries, Inc.