sony kdl-32-
TRANSCRIPT
-
Models: AZ1K ChassisKDL-32EX301 KDL-32EX500 KDL-46EX400KDL-32EX400 KDL-40EX500 KDL-46EX500KDL-40EX400 KDL-40EX501 KDL-46EX501KDL-40EX401
Triage and Troubleshooting GuideCourse: CTV-61
Training Manual
KDL-40EX500
-
CTV-61 i
Section 1 - AZ1K Chassis Models Overview ..................... 3AZ1K Chassis Models Covered ....................................... 5Model Introduction ........................................................... 5AV Input & Output Descriptions ....................................... 5
RF Input ............................................................................... 5
Composite Video & Audio Inputs ......................................... 5
Component/Composite Video & Audio Inputs ...................... 6
HDMI/DVI Video Input and DVI Video ................................. 6
PC Video & Audio Input (and DVI Audio) ............................. 6
USB 2.0 Side Connection - Photos & Music ........................ 6
Audio Outputs .................................................................. 7Fixed Analog Audio Output .................................................. 7
Digital Audio Output (Optical) .............................................. 7
32 & 40 Models Overall PCB Block Diagram ............... 846 Models Overall PCB Block Diagram .......................... 9PCB and Component Descriptions ................................ 10
A-Board ............................................................................. 10
G2LE-Board (32") or G2HE-Board (40") ............................ 10
GD2-Board (46") ................................................................ 10
Backlight Inverter Board (32" & 40") .................................. 10
H2-Board ........................................................................... 10
Switch Unit ......................................................................... 10
LCD Panel Assembly ..........................................................11
Section 2 - Troubleshooting Procedures ......................... 12Power Symptom Troubleshooting .................................. 12
Table of ContentsNormal Operation .............................................................. 12
Failure Symptoms .............................................................. 12
No Power/Dead Set (No RED Standby LED) .............. 12
32 & 40 Power Supply System Block Diagram ........... 14G2LE-Board & G2HE-Board Connector Diagram ......... 1546 Power Supply System Block Diagram ..................... 16GD2-Board Connector Diagram .................................... 17Protection Mode Symptom Troubleshooting .................. 18
Failure Symptoms .............................................................. 18
2X Blink - Main Power Error ........................................ 18
3X Blink- Audio Error ................................................... 18
4X Blink - Balancer Failure (46 Models ONLY) .......... 19
5X Blink - TCON & HFR Failure .................................. 19
6X Blink - Backlight System Failure (32 & 40 Models) 19
6X Blink - Backlight System Failure (46 Models) ........ 19
7X Blink - Temperature Failure .................................... 20
32 & 40 Models Protection Mode System Block Diagram 21
46 Models Protection Mode System Block Diagram .... 22All Models Power Board Protection Circuits Block Dia-
gram ........................................................................... 23Video Symptom Troubleshooting ................................... 24
Normal Operation .............................................................. 24
Troubleshooting ................................................................. 24
Missing or Distorted Video (Individual Inputs) ................... 24
Missing Video (All Inputs) .................................................. 25
-
CTV-61 ii
Table of Contents
Skewing LVDS Connector Troubleshooting Method .... 25
Distorted Video (All Inputs) ................................................ 25
WIDE Mode Button (Aspect Ratio) Troubleshooting Method ................................................................... 25
Unique Main Video Board (A-Board) or LVDS Cable Ef-fects ....................................................................... 26
Unique TCON/HFR Board Effects ............................... 27
Unique LCD Panel Assembly Effects ........................... 27
Common Main Video Board (A-Board) and LCD Panel Assembly Effects ................................................... 27
Video System Block Diagram ........................................ 28Audio Symptom Troubleshooting ................................... 29
Normal Operation .............................................................. 29
Failure Symptoms .............................................................. 29
Missing or Distorted Main Speaker Audio - All Inputs .. 29
Missing or Distorted Main Speaker Audio - Individual Inputs ..................................................................... 29
Audio System Block Diagram ........................................ 30
Section 3 - Service Mode .................................................. 31Service Mode Access .................................................... 31
Section 4 - Triage & Troubleshooting Flowcharts .......... 32Triage Flowchart ............................................................ 32Power-ON Troubleshooting Flowchart ........................... 33Protection Mode 2X, 3X, & 4X Troubleshooting Flowchart
34Protection Mode 5X & 6X(32, 40) Troubleshooting Flow-
chart ........................................................................... 35Protection Mode 6X(46) & 7X Troubleshooting Flowchart
36Video Troubleshooting Flowchart .................................. 37Audio Troubleshooting Flowchart .................................. 38
Appendix ............................................................................. 39LCD Panel Distortion Pictures ....................................... 39TCON/HFR Board Distortion Pictures ........................... 40TCON/HFR Board Distortion Pictures Continued .......... 41Video Board Distortion Pictures ..................................... 42Video Board Distortion Pictures Continued ................... 43
-
CTV-61 3
Section 1 - AZ1K Chassis Models Overview
32 & 40 OVERALL PCB LOCATION DIAGRAM FIGURE 1-1
G2LE-Board (32")G2HE-Board (40")
A-Board
Backlight Inverter Board
32" & 40" Models
TCON Board
Switch Unit
H2-Board
LVDS Cable
-
CTV-61 4
AZ1K Chassis Models Overview
GD2-Board
A-Board
Balancer Board
46" Models
TCON Board
Switch Unit
H2-Board
LVDS Cable
46 OVERALL PCB LOCATION DIAGRAM FIGURE 1-2
-
CTV-61 5
AZ1K Chassis Models Overview
AZ1K Chassis Models CoveredKDL-32EX301 KDL-32EX500 KDL-46EX400
KDL-32EX400 KDL-32EX501 KDL-46EX500
KDL-40EX400 KDL-40EX500 KDL-46EX501
KDL-40EX401 KDL-40EX501
Model IntroductionAll models, except the KDL-32EX301, contain a Full High-Denition 1920 X 1080 resolution panel. The KDL-32EX301 contains a 1280 X 720 resolution panel. The backlight is produced using a Cold Cathode Fluorescent Lamp (CCFL) light system for all models. All models have the Advanced Contrast Enhancer (ACE) feature and Dynamic Backlighting. The Dynamic Contrast Ratio (DCR) for the 400 series is 140,000:1 and for the 500 series it is 2150,00:1. All models contain the BRAVIA Engine 2 digital video processor for superior resolution. Plus, 7 HD inputs (4 HDMI, 2 component and 1 PC) are provided to connect all of your HD devices including PLAYSTATION3, Blu-ray Disc player and laptop or desktop.
The BRAVIA Engine 2 fully digital video processor uses a collection of unique Sony technologies to signicantly reduce noise, enhance overall image detail, and optimize contrast so every scene produces sharp, vibrant, life-like images and color.
The EX500 series models contain the Motionow 120Hz frame rate technology which enhances sharpness and delivers smooth motion for fast-action sports and movies. The EX300 and EX400 series models contain the standard 60Hz frame rate.
Sony HDTVs exceed Energy Star 3.0 requirements. In addition, they incorporate advanced power saving features such as Light Sensor technology that adjusts backlight intensity based on ambient room lighting conditions and Dynamic Backlight Control that adjusts backlight intensity based on the brightness of the image on the screen.
AV Input & Output Descriptions
Composite
PC Input
HDMI Input
HDMI Input
HDMI/DVI InputDigital Audio
Output(Optical)
Analog Audio Output (FIXED)
Component Input
Component/Composite Input
RF Input
USB
HDMI Input
PC & DVI Audio Input
RF InputThis is a 75 ohm connection for either terrestrial NTSC and ATSC (8VSB) or cable QAM64 and QAM256 signals.
Composite Video & Audio InputsYellow Jack - Composite Video InputRed & White Jacks - Right & Left Audio InputNOTE: The second composite input is shared with one of the component inputs. Reference the description of the component inputs for details on activating the composite input.
-
CTV-61 6
AZ1K Chassis Models Overview
Component/Composite Video & Audio InputsRed, Blue, & Green Jacks - Component Video InputsRed & White Jacks - Right & Left Audio InputNOTE: Composite video can be applied to the component input label VIDEO IN. The yellow composite video connector is connected to the green component connector. The audio is connected to the same component audio inputs.IMPORTANT: For automatic signal detection make sure the User Menu item is set to AUTO. Reference the below for the specic menu item. The input can also locked to Video 1 (composite) or Component 1 (component) signal. However, the input will only process the chosen signal type. If the other signal type is connected the picture will be lost or black & white.
Select the appropriate input for the input signal type.Auto Auto DetectionVideo 1 CompositeComponent 1 - Component
HDMI/DVI Video Input and DVI VideoBoth the HDMI and DVI formats contain digital video. In the case of the HDMI format the audio is also digital and is part of the video and audio data stream over the single HDMI connection. In contrast, the DVI format contains only digital video in its data stream. The audio is sent over a separate Stereo Mini Jack audio connection. Furthermore, a DVI to HDMI adapter is required to connect the DVI connector to the HDMI connector.
PC Video & Audio Input (and DVI Audio)All EX models have a Personal Computer Input (PC-IN), which connects directly to the PC 15 pin DIN connector (HD15 connector). Once connected the TV functions as a video monitor and audio output (separate Stereo Mini Plug) for the PC audio. There is a complete table of PC Input Signal Compatibility in the Owners Manual for each model.
The Stereo Mini Plug is also used for a DVI audio connection at HDMI 1 video input. The DVI video is connected through an adapter to HDMI 1 input and the DVI audio to connected to the Stereo Mini Jack.
USB 2.0 Side Connection - Photos & MusicConnect a camera, USB-Enabled MP3 player, or USB storage device directly to this side USB input to view JPG photos and MPEG1 & MPEG2 videos on the screen or listen to MP3 music les.
This USB connection is also used for TV Software updates using a USB drive device.
-
CTV-61 7
AZ1K Chassis Models Overview
Audio Outputs
Fixed Analog Audio OutputThis audio output can be used to listen to the TV audio through an external AV stereo system. The audio level at the output is set to a xed level and cannot be turned off or adjusted.
Digital Audio Output (Optical)Connects to the optical audio input of any digital audio equipment that is PCM/Dolby digital compatible. The following table shows the audio inputs and the audio format which are present at the Optical Audio Output per input format.
Audio Input Source Optical OutputDigital Tuner 5.1 (ATSC) 5.1 DolbyHDMI 5.1 5.1 DolbyAll Analog Audio Inputs 2CH PCMAnalog Tuner (NTSC) 2CH PCMSACD Format (HDMI) No OutputDVD Audio Format (HDMI) No Output
-
CTV-61 8
AZ1K Chassis Models Overview
32 & 40 OVERALL PCB BLOCK DIAGRAM
FIGURE 1-3
32 & 40 Models Overall PCB Block Diagram
CCFL Backlight HV Inverter Circuits
Backlight System Error Circuits
Backlight Inverter Board
A-Board
TV Microprocessor MT5388:
Video ProcessingHDMI ProcessingHDCP ProcessingIP (Image Processor)Scan Converter (Scalar)
HDMI Switcher ATSC/NTSC Tuner Temperature Sensor Audio Output Amplifier
Control
Power/Drive
LVDS
Keys
Power/SIRCS
LCD Panel Assembly
LCD PANEL
Power Key Function Keys
Switch Unit
LEDs IR Sensor
H2-Board
Power
Main Power Supply Standby Power Supply
G2LE-Board (32")G2HE-Board (40")
Power
Control
Power
LCD Panel
R
L
RF Input
1 Composite Input
2 Component Inputs(Composite can be applied to Component 1)
1 PC Input
3 HDMI Inputs
Optical Digital Audio Output
Analog Audio Output
CCFLBacklight System
TCON/HFRPower
AC Input
*High Frame Rate (120HZ)
1 USB 2.0
-
CTV-61 9
AZ1K Chassis Models Overview
46 OVERALL PCB BLOCK DIAGRAM
FIGURE 1-4
Balancer Board
A-Board
TV Microprocessor MT5388:
Video ProcessingHDMI ProcessingHDCP ProcessingIP (Image Processor)Scan Converter (Scalar)
HDMI Switcher ATSC/NTSC Tuner Temperature Sensor Audio Output Amplifier
Control
Power/Drive
LVDS
Keys
Power/SIRCS
LCD Panel Assembly
LCD PANEL
Power Key Function Keys
Switch Unit
LEDs IR Sensor
H2-Board
Power
Main Power Supply Standby Power Supply AC Relay Backlight HV Inverter
Circuits
GD2-Board
HV
Control
Power
LCD Panel
R
L
RF Input
1 Composite Input
2 Component Inputs(Composite can be applied to Component 1)
1 PC Input
3 HDMI Inputs
Optical Digital Audio Output
Analog Audio Output
CCFLBacklight System
TCON/HFRPower
AC Input
*High Frame Rate (120HZ)
1 USB 2.0
HV
46 Models Overall PCB Block Diagram
-
CTV-61 10
AZ1K Chassis Models Overview
PCB and Component DescriptionsReference Figures 1-3
A-Board The circuits located on the A-Board perform all Video and Audio processing functions. It also contains all the microprocessor control circuits. The following circuits are included on this board.
TV Microprocessor MT5388 Processor - Video Signal Processing
- HDMI Signal Processing
- Scan Converter
- HDCP Processing
Audio Amplier Temperature Sensor
G2LE-Board (32") or G2HE-Board (40")Except for some regulator circuits on the A-Board, the G2LE-Board or G2HE-Board is the power supply system board for the 32 and 40 models, which includes the following components and circuits.
Main Power Supply 12V AU12V (Audio Amp) 24V (Backlight Inverter)
Standby Power Supply 3.3V for standby circuits
Power Factor Control Circuit (PFC)
GD2-Board (46")Except for some regulator circuits on the A-Board, the GD2-Board is the power supply system board for the 46 models, which includes the following components and circuits.
Main Power Supplyo 12V
o AU12V (Audio Amp)
Standby Power Supplyo 3.3V for standby circuits
Backlight High Voltage Inverter Power Supply Main/Inrush AC Input Relay Power Factor Control Circuit (PFC)
Backlight Inverter Board (32" & 40")The 24V developed in the Main Power Supply on the G2LE-Board or G2HE-Board powers the Backlight Inverter Board. The Inverter Board takes that 24V and develops approximately 2KVrms to initially ignite the lamps and 1KVrms to drive the backlight Cold-Cathode-Fluorescent Lamps (CCFL) in normal operation.
H2-Board IR Sensor
Switch Unit Power Key Function Keys
-
CTV-61 11
AZ1K Chassis Models Overview
LCD Panel AssemblyThe LCD Panel Assembly includes the LCD Panel, TCON Board (300 & 400 series models), TCON/HFR Board (500 series models), and CCFL Backlight system.
The LCD Panel contains the actual liquid crystals, color lters, and polarizers. The liquid crystals are manipulated by the applied voltage to pass a specic amount of light - from the backlight- depending on the level of voltage applied.
The TCON performs all the control, timing, charge, and discharge functions driving the operation of the LCD Panel. The HFR (High Frame Rate) section performs the 60Hz to 120Hz frame refresh rate conversion.
A replacement LCD Panel assembly from parts will include the following items.
32 & 40 Models:
1) LCD Panel and Backlighting Components
2) TCON/HFR Board
3) Inverter Board
46 Models:
1) LCD Panel and Backlighting Components
2) TCON/HFR Board
3) Balancer Board
-
CTV-61 12
Section 2 - Troubleshooting Procedures
Power Symptom Troubleshooting
Normal OperationReference Figure 2-1 and 2-2
110VAC is applied to the G2LE-Board, G2HE-Board, or GD2-Board it can be measured at CN6101 or CN6003. In the standby mode the AC power passes through the main fuse F6101 or F6001. The is no main relay on the G2LE & G2HE-Board so the AC power is applied directly to the Main & Standby Power supply. The GD2-Board does have a Main AC Relay. The AC power passes through R6003 (Inrush resistor), and D6001 and is applied to the Main DC/DC Converter IC6501 and the Standby DC/DC Converter IC6201. IC6501 is not active in the standby mode. However, IC6201 is active in standby mode and outputs STBY 3.3Vdc as long as AC power is applied to the TV. The Standby 3.3Vdc is supplied to the TV-Microprocessor, Switch Unit (Power Key), and HSR-Board (IR Sensor) in the standby mode.
Once a ON command is received form the remote controller or the power button on the Switch Unit the TV-Microprocessor outputs the Power-ON signal. The Power-On signal is applied to the G2LE-Board, G2LE-Board, or GD2-Board. On the power supply board the Power-On signal switches the 19V from the standby power supply to activate the PFC and Main Power supply IC6501. No relay click will be heard on the 32 or 40 models because there is not a main relay. However, on the 46 models there is a main relay and one relay click is heard at power-on. The relay engages to bypass the inrush resistor R6003 during the ON state.
The main power supply IC6501 is now active and outputting all secondary supplies. The 12Vdc secondary is the supply voltage for all the voltage regulators on the A-Board. The AU12V is the supply voltage for the audio output amplier. The 32 and 40 models power supply will also output 24V which is the supply voltage for the backlight inverter board.
The GD2-Board in the 46 models will develop and output the backlight high-voltage (1KV) to the Balancer board and the CCFL backlights.
Failure SymptomsReference Figures 2-1, 2-2, 2-3, and 2-4
No Power/Dead Set (No RED Standby LED)In a dead set condition there will be No RED Standby LED illumination in the Standby Mode (TV plugged into an active AC Outlet).
The following bullet list gives the possible failures for a No Power/Dead Set condition.
Loss of AC Power
Loss of AC-OFF-DET
Loss of Standby 3.3Vdc
Loss of REG12V
Loss of Power-On
Defective Main Microprocessor
The rst step in troubleshooting a No Power/Dead Set condition is to conrm that 110ACV power from an active AC outlet is applied to the G2LE-Board, G2LE-Baord, or GD2-Board. AC power is applied to, and can be measured at CN6101 on the G2BE-Board or G2CE-Board and at CN6003 on the GD2-Board.
Next, check for the presence of the AC-OFF-DET voltage at CN6401/pin 2 or CN6150/pin 2. If the AC-OFF-DET circuit is working properly 3V should be measured. If the 3V is not present replace the G2BE-Board, G2CE-Board, or GD2-Board. If the 3V in not present either the main fuse or the main power supply IC6501 is defective. In either case, replace the power supply board.
After conrming the AC power and AC-OFF-DET, check for a defective Standby 3.3Vdc power supply IC6201. To conrm a defective IC6201 check the 3.3V secondary voltage at CN6401/pin 1 or CN6150/pin 1. As long as AC power is applied to the TV IC6201 should be active and outputting 3.3Vdc. If the 3.3V is not present then IC6201 is defective. Replacing the power supply board will x the problem.
-
CTV-61 13
AZ1K Chassis Models Overview
Finally, a Dead Set condition can be caused by a defective microprocessor IC400. The microprocessor outputs the Power-On signal which activates the switch Q6301 and IC6301 on the power supply board and passes the 19V from the Standby power supply to active the relay (46 models), PFC, and Main Power Supply IC6501. If the Power-On signal is not output after receiving the Power-ON command the power supply board circuits remain inactive and a Dead Set condition exists. The Power-On signal can be checked at CN6401/pin 3 or CN6150/pin 3. It should measure approximately 3.3Vdc If the measurement is 0Vdc before shut-off the TV microprocessor is defective. Replace the A-Board. If the power-on voltage is 3V before shutdown then the switch circuit on the power supply board is defective. Replace the power supply board.
-
CTV-61 14
AZ1K Chassis Models Overview
A-Board
AU12V
12V
3V
F6101
AC Input
D6301TH6301
CN6402
STBY 3.3V
L6302
19V
24V
Power ON
Panel 12V
IC902Standby
3.3VPower Supply
CN6101
SwitchCircuitQ6101Q6102
IC6301Main
Power Supply
&PFC
BacklightHV Inverter
Board
LCD PANEL
IC400MT5388
CCFL Backlights
TCON/HFR
LCD Panel Assembly
VCC
R63420.1ohm
R610710ohm
VSense
CN201CN6401
Q6302Q6303
Q63045V
IC8151Audio Output Amp
1.1KV (~2KV Strike Voltage)
LVDS Cable
F1
G2LE-Board (32")G2HE-Board (40")
AC-OFF-DET3V
LCD Panel
9 9
4 4
3
ON/OFF
AC_DET
PFC_OUT
Q6403 TCON 12V
PS6402
PS6401
AC_DET
D6302
1
2
1
2
CN6401
CN6403
1
2
33PH6103
TCON ON15 15
IC2315V Reg
IC2665V Reg
5V
To Tuner
IC2321V Reg
IC2673V Reg
IC2681.25V Reg
To MicroIC2691V Reg
To Micro To MicroTo DDR
To USBTo Optical Out
IC8301Line Out Amp
A-Board
1014
To CN6401
From Q6403
LVDS 12V
CN201
8
D6308
R6302 L6303
3V
12V
19V
12V
12V
EX500 Series ONLYEX400 Series No Connection
HFR on EX500 Series Only
32 & 40 Power Supply System Block Diagram
32 & 40 POWER SUPPLY SYSTEM DIAGRAM FIGURE 2-1
-
CTV-61 15
AZ1K Chassis Models Overview
F1
AC Input
CN6401CN6402
1 UNREG24V2 UNREG24V3 UNREG24V4 UNREG24V5 UNREG24V6 Ground7 Ground8 Ground9 Ground10 Ground11 BL-ERR12 BL-ON13 NC14 - Dimmer
15 TCON-ON14 TCON 12V 13 NC12 DIMMER11 BL-ON10 BL-ERR 9 REG12V8 REG12V7 Ground6 Ground5 Ground4 AU12V3 POWER-ON (3V)2 AC-OFF-DET (3V)1 STBY 3.3V
G2LE-Board (32")G2HE-Board (40")
CN6101
G2LE-Board & G2HE-Board Connector Diagram
G2LE-BOARD & G2HE-BOARD CONNECTOR DIAGAM FIGURE 2-2
-
CTV-61 16
AZ1K Chassis Models Overview
A-Board
AU12V
12V
3V
F6001
AC Input
D6001
CN6704
STBY 3.3V
L6501
19V
Power ON
IC6201Standby
3.3VPower Supply
CN6003
SwitchCircuitIC6301Q6301
IC6501Main
Power Supply
&PFC
Balancer Board
LCD PANEL
IC400MT5388
CCFL Backlights
TCON/HFR
LCD Panel Assembly
VCC
R65360.1ohm
R620110ohm
VSense
CN201CN6150
Q65025V
IC8151Audio Output Amp
1.1KV (~2KV Strike Voltage)
LVDS Cable
F1
GD2-Board
AC-OFF-DET3V
LCD Panel
9 9
4 4
ON/OFF
AC_DET
PFC_OUT
Q6151 TCON 12V
PS6151
AC_DET
D6002
1
2
1
2
CN6150
CN6151
2
33PH6300
TCON ON15 15
IC2315V Reg
IC2665V Reg
5V
To Tuner
IC2321V Reg
IC2673V Reg
IC2681.25V Reg
To MicroIC2691V Reg
To Micro To MicroTo DDR
To USBTo Optical Out
IC8301Line Out Amp
A-Board
1014
To CN6150
From Q6151
LVDS 12V
CN201
8
D6502
R6013 R6301
3V
12V
19V
12V
RY6002
HV
HV
Backlight Inverter High Voltage CircuitsIC6601Q6601Q6602
19V 400V CN6705
R6003
46 Power Supply System Block Diagram
46 POWER SUPPLY SYSTEM DIAGRAM FIGURE 2-3
-
CTV-61 17
AZ1K Chassis Models Overview
F6001
AC Input
CN6151
CN6150
CN6158
CN6705
CN6003
AC Relay
6 - NC5 - Ground4 Ground3 TCON 12V2 TCON 12V1 NC
HV 1.1KVHV 1.1KV
GD2-Board
CN6704
15 TCON-ON14 TCON 12V 13 NC12 DIMMER11 BL-ON10 BL-ERR 9 REG12V8 REG12V7 Ground6 Ground5 Ground4 AU12V3 POWER-ON (3V)2 AC-OFF-DET (3V)1 STBY 3.3V
5 - LD4 Ground3 Ground2 FB1 12V
GD2-Board Connector Diagram
GD2-BOARD CONNECTOR DIAGAM FIGURE 2-4
-
CTV-61 18
AZ1K Chassis Models Overview
Protection Mode Symptom TroubleshootingReference Figures 2-5 and 2-6
The KDL-32S5100 and KDL-32XBR9 include the following protection mode blink patterns (or self-diagnostics).
Protect Description Blink Pattern Possible Error Location
Main Power Error 2 G2LE, G2HE, GD2-Board, or A-Board
Audio Error 3 A-Board or G2LE, G2HE, GD2-BoardBalancer Error (46 Only) 4
LCD Panel, A-Board, or GD2-Board
TCON Error 5 TCON/HFR Board or A-Board
HFR Error 5 TCON/HFR Board or A-Board
Backlight Error 6
Inverter Board (32, 40), G2LE, G2HE, GD2-Board, LCD Pan-
el, or A-BoardTemperature Error 7 Ventilation or A-Board
NOTE: All red protection mode LED blink patterns occur using the Standby-LED at the lower left front of the TV.
Failure Symptoms
2X Blink - Main Power ErrorA 2X protection mode blink pattern can be activated due one of the following defects on the G2LE-Board, G2HE, GD2-Board..
Loss of AU12V (LVP)*
Excessive AU12V Level (OVP)*
Excessive 24V Level (OVP) (32 & 40 models)
Excessive PFC Voltage (OVP)
Excessive PFC Temperature (OTP)
*Low Voltage Protection (LVP)
*Over Voltage Protection (OVP)
A loss or excessive condition of the AU12Vdc secondary voltage from the main power supply IC6501 will cause a 2X blink pattern on the Standby-LED. The 12Vdc can be checked at CN6401/pin 4. The
If the measurement is 0V or rises above 12Vdc (approaches 15V) before the TV shutdown the G2LE-Board, G2LE, GD2-Board is defective.
If approximately 12Vdc is present and remains below 12Vdc before shut-off then the A-Board is defective.
An excessive 24Vdc (32 & 40 models) secondary voltage from the main power supply IC6501 will also cause a 2X blink pattern on the Standby-LED. The 24Vdc can be measured at CN6402/pin 3 before TV shutdown. If the voltage rises above the 24V level (approaches 27) before TV shutdown then the power supply is defective, replace the G2LE, G2HE , GD2-Board to x the problem.
Finally, there are PFC protection circuits on the power supply board that when activated will cause a 2X blink protection mode (reference Figure 2-7). The PFC circuit is monitor for both over-voltage and over-temperature. Therefore, if the AU12V and 24V circuits checkout okay, there could still be a problem on the power supply board in the PFC circuit causing the 2X blink. Replace the G2LE, G2HE, GD2-Board to x this condition.
3X Blink- Audio ErrorThe Audio error can occur due one of the following error conditions.
Shorted or Damaged Speaker Connections
Defective Audio Amplier (A-Board)
Loss of AU12V (Open F1 on A-Board)
The rst thing to check when a 3X blink protection mode occurs is the physical condition of the speakers and speaker connections. The speakers
-
CTV-61 19
AZ1K Chassis Models Overview
should measure 8 ohms. Shorted speakers or connections can cause a 3X blink protection mode.
If the speakers and connections check okay, then the defective component is on the A-Board. Either a open F1 or defective audio amplier will cause a 3X blink protection mode. In either case, replace the A-Board to x this condition.
4X Blink - Balancer Failure (46 Models ONLY)In most cases, a 4X protection mode indicates a defective lamp or lamps. Therefore, replace the LCD panel to x this condition. If the 4X protection is still present after replacing the LCD panel, there could be a problem on the A-Board or GD2-Board. First replace the A-Board then the GD2-Board.
5X Blink - TCON & HFR FailureThe 5X blink protection mode indicates a communications error between the TCON/HFR board and the MT5388 microprocessor on the A-Board. First replace the TCON/HFR Board if the 5X protection mode blink pattern occurs. If the TCON/HFR Board does not repair the problem then replace the A-Board.
6X Blink - Backlight System Failure (32 & 40 Models)NOTE: All models will make three attempts to power up before a 6X error is activated. The SONY logo (Backlight) will display on the screen and the tones (with Volume up) will be heard three times. After the third attempt the TV will turn off and the Standby LED will blink a 3X protection mode.In most cases, if the backlight momentarily illuminates and the TV shuts off and a 6X is activated than one or more of the backlight lamps are defective. The LCD Panel assembly panel must be replaced for a defective lamp.
If a 6X blink pattern is activated than a defect has occurred in one of the following areas.
Defective Panel Lamp(s) Defective Backlight Inverter Board Defective TV Microprocessor Defective 24V Power Supply
When troubleshooting a 6X backlight system failure it is key to notice if the backlights illuminate before the TV shuts off. The following list shows the possible backlight status and blink pattern and the possible failed components.
1) Momentary Backlight and 6X
a) Defective Lamp(s)
b) Defective Backlight Inverter Board
2) No Backlight and 6X
a) Defective TV Microprocessor
b) Defective 24V Power Supply
c) Defective Backlight Inverter BoardIMPORTANT: Before replacing the LCD Panel assembly check the backlight Inverter Board outputs. A failure of one of the inverter outputs will also cause this same symptom (Momentary Backlight & 6X).If there is no backlight before the TV shuts off and activates a 6X, than check the Backlight ON signal from the TV microprocessor and the 24V power supply from the G2LE, G2HE, GD2-Board.If the Backlight ON and 24V power supply are okay than the Backlight Inverter board has failed and must be replaced. This will be a rare occurrence but the Inverter board can cause a No Backlight condition and must be considered.
6X Blink - Backlight System Failure (46 Models)The 46 models have both a 4X and 6X blink protection mode. The 4X blink will, in most cases, be caused by a defective lamp.Because all the Backlight HV Inverter circuits are located on the GD2-Board, a 6X blink protection mode will be xed, in most cases, by replacing the GD2-Board. If the GD2-Board does not repair the problem replace the A-Board. The BL-ON and Dimmer signals come from the
-
CTV-61 20
AZ1K Chassis Models Overview
microprocessor on the A-Board. A shorted or open BL-ON signal will cause this 3X condition. Also a shorted Dimmer will cause this 3X condition.
7X Blink - Temperature FailureThese models do not display a temperature warning OSD dialogue box before shutting-off and going into a 7X Standby-LED blink pattern. It will just shut-off and activate a 7X without any usually warning on the screen.
The main objective when a 7X blink pattern occurs is to determine which of the following possible defects is causing the excessive temperature condition.
Excessive Ambient Room Temperature Dust or Debris Blocking the TV Ventilation Apertures Defective Temperature Sensor IC4305 or MT5388
microprocessor (A-Board)
The rst step is to notice how long it takes the TV to shut-off and trigger a 7X blink protection mode.
If the TV has an actual excessive temperature condition it will take a considerable period of time to shut-off and indicate a 7X blink protection mode. This is because it will take time for the TV to heat up and for the temperature sensor to detect the excessive temperature and shut the TV off
If the TV takes a considerable period of time to shut-off check the following items:
The TV should not be located too close to any heating elements.
The TV should have at least 4 inches of clearance around all sides to ensure adequate ventilation.
Check that all vented areas on the TV are clear of all Dust and Debris.
If the TV shuts-off immediately (Not an Actual Excessive Temperature Condition) after Power-ON then one of the following components has
failed.
Main Microprocessor IC3002 (A-Board) Temperature Sensor IC3502 (A-Board)
In either case the A-Board must be replaced to x the problem.
-
CTV-61 21
AZ1K Chassis Models Overview
A-Board
3X
IC400MTK5388
2X
Standby 3.3V
DC_Detect Main PS&
PFC
AC Input
STBYPS
CN6401CN60003V
Power ONSW
RECT
IC4305Temp
Sensor70C
HV Inverter Board
BL_ERRBL_ON
Dimmer24V
CN001
12V
BL_ERRBL_ONDimmer
INV_ERR
6X
Temp_ERR
7X
IC8151Audio Amp
Protection CircuitQ8153, Q8155Q8158, Q8160,
Q8156Audio_ERR
LCD Panel Assb
TCON
TCON_ERR5X
HFR_ERR5X
SDA (I2C)
HFR
8
1 1
3 3
6123
CN8151CN8152
CN4152
G2LE-Board (32")G2HE-Board (40")
Interface Circuit
324V
BL*Backlight Inverter
High Voltage Corcuits
*BL - Backlight
1V to 3V3V0V
131211
CN201
9
CN6401
CN6402
3V
3.3V
RECT
32 & 40 Models Protection Mode System Block Diagram
PROTECTION CIRCUITS DIAGRAM FIGURE 2-5
-
CTV-61 22
AZ1K Chassis Models Overview
A-Board
3X
IC400MTK5388
2X
Standby 3.3V
DC_Detect Main PS&
PFC
AC Input
STBYPS
CN60033V
Power ONSW
RECT
IC4305Temp
Sensor70C
BL_ERRBL_ON
Dimmer
CN6150
12V
BL_ERRBL_ONDimmer
BL_ERR
4X & 6X
Temp_ERR
7X
IC8151Audio Amp
Protection CircuitQ8153, Q8155Q8158, Q8160,
Q8156Audio_ERR
LCD Panel Assb
TCON
TCON_ERR5X
HFR_ERR5X
SDA (I2C)
HFR
8
1 1
3 3
121110
CN8151CN8152
CN4152
GD2-Board
Interface Circuit
BL*
Backlight Inverter High Voltage
Circuits
*BL - Backlight
1V to 3V3V0V
131211
CN201
9
CN1004
CN6150
3V
3.3V
RECT
BALANCER
HV
HV
FB
LD12V
CN6702
PROTECTION CIRCUITS DIAGRAM FIGURE 2-6
46 Models Protection Mode System Block Diagram
-
CTV-61 23
AZ1K Chassis Models Overview
IC6301Main
Power Supply
&PFC
AC Input
12V OVP
Reg 12VD6301
PFC OVP
Switch CircuitQ6101, 6102
30V Zener
To A-Board
Power-ON From A-BoardPulls
Power_ON Low
G2LE-Board (32")G2HE-Board (40")GD2-Board (46")
OVP Over Voltage ProtectionOTP Over Temperature Protection
CN6401
33V
Latch CircuitQ6202, 6203
G2HE-Board & G2LE-Board Protection circuits will cause a 2X blink pattern
Reg 24V
15V Zener
24V OVP
9
3 To Inverter Board
CN6402
19V
PFC OTP
D6302
CN6101
OTP
32" 40" Models ONLY
PROTECTION CIRCUITS DIAGRAM FIGURE 2-7
All Models Power Board Protection Circuits Block Diagram
-
CTV-61 24
AZ1K Chassis Models Overview
Video Symptom TroubleshootingReference Figure 1-8
Normal OperationAll video processing is performed by IC400 (MT5388) on the A-Board. The RF input is rst processed by the RF Tuner and is then applied to IC400. Both the ATSC and NTSC signal are processed by IC400. All four HDMI inputs are rst applied to a HDMI switch circuit (IC6601). The switch circuit applies the selected input to IC400. IC6601 also contains the EDID (Extended Display Identication Data), which is part of the HDMI hand-shake process.
All other inputs (Composite, Component, PC, and USB) are connected directly to IC400 inputs.
The USER, White Balance, and Gamma data is stored in IC4302.
Both the USER Menu and Service Mode screen are generated by, and output from IC400.
IMPORTANT:
1) Conrm the TV has the most recent Software Version installed. Go to the User Menu for the present TV software revision and the ASC web site for the most recent software version.
2) Before proceeding with the following video troubleshooting procedures it is assumed that the TV is turning on with the Green Power-LED illuminated, Backlight is illuminated (brightened raster), and the Audio is present.
TroubleshootingWhen a video problem occurs you will experience one of the two following symptoms.
Input Status:
Missing or Distorted Video (Individual Inputs) Missing or Distorted Video (All Inputs)
Video Anomaly:
Poor Detail Moving Video Distortion (e.g. Bars) Static H/V Lines (Any Color) Static Missing Pixels (Any Color) Static Bars (Solid Black or White, Transparent Color) White Balance Gamma
The main objective when troubleshooting one of the previously listed symptoms is to determine if the defect exists in the following sections of the TV system.
LCD Panel Assembly TCON/HFR Board A-Board
Missing or Distorted Video (Individual Inputs)The primary objective is to locate the defective component through activating each individual video input and checking for any abnormal symptoms on the screen. If the video distortion appears only in one or two video inputs then the next step is to eliminate the possibility of a defective or improperly connected external device such as, a STB, DVR or DVD player. The quickest way to troubleshooting the external devices is to swap the suspect device with a known good device at the input in question.
If the external device or connections are defective then the TV is okay and the external device and connections need to be serviced. If the external devices and their connections are okay, then the next step is to troubleshoot the problem by accessing and displaying each video input.
The rationale behind this troubleshooting method is that each of these video inputs takes an altogether or somewhat different path through the video processing system. This fact enables you to determine the defect,
-
CTV-61 25
AZ1K Chassis Models Overview
in some cases, down to the component level, and in almost all cases, down to at least the board level. For example, if the distortion appears in a HDMI input but not in any other inputs (e.g. composite or component) then most likely the HDMI Switcher (IC6601) is causing the distortion. The reason for this conclusion is because the HDMI signals are the only signals to pass through IC6601 before being applied to IC400. All other input signals bypass IC6601. The composite and component signals go directly to the video processor IC400.
Although all the individual input circuits are located on a single board (A-Board), the previously described troubleshooting procedure can still serve as a reliable conrmation of a defective component on the A-Board before replacing the board.
The same deductive reasoning can be applied when troubleshooting video defects using the other video inputs shown on the owchart (Section 4). This method simply involves knowing the path the input signal must take through the video processing system to reach the display. With this knowledge you can effectively divide the video system into distinct areas, and therefore, isolate the defect.
Missing Video (All Inputs)If the video is completely missing you will rst use the User Menu (On-Screen-Display - OSD) in an attempt to isolate the defect to the A-Board or the TCON/HFR Board.
If the OSD can be displayed then the TCON/HFR Board is okay, and you can safely assume the defect exists on the A-Board. However, if the OSD cannot be displayed you need to do further troubleshooting because either IC400 on the A-Board is not sending the OSD or the TCON/HFR Board is not able to process the OSD and display it on the LCD Panel.
If the OSD cannot be displayed then the LVDS signal levels must be checked to reliably determine whether the A-Board or the TCON/HFR Board is defective.
1) Check for USER Menu OSD Display
a) USER Menu Displays. Replace A-Board
b) USER Menu Does Not Display. Go to Step 2
2) Check for TCON 12V at CN4152/pins 4 - 10 & CN6151/pin 2
a) No 12V. Check connections between A-Board & Panel
b) 12V Present. Go to Step 3
3) Check LVDS Cable Video Signal Levels at CN4152
a) LVDS Video Signal(s) Low or Missing. Replace A-Board
b) LVDS Video Signal(s) Okay. Replace TCON/HFR Board
Skewing LVDS Connector Troubleshooting MethodIt maybe difcult or impossible to check the LVDS signal while in the eld. Therefore, a quick and somewhat reliable method of checking the TCON/HFR operation is to skew the LVDS connector out of the its mount at the TCON/HFR Board. When performing this method it is important to keep the 12V end of the connector connected while dislodging the LVDS video connections. Therefore, nd the 12V using a voltmeter. The 12V is usually on one end of the connector (usually left-side on bottom mount or top on side mount connect).
When skewing the connector if color ashing occurs on the screen then the TCON/HFR Board is most likely okay and the A-Board is defective. If the is no video reaction on the screen while skewing the connector then the TCON/HFR Board is defective.
Distorted Video (All Inputs)The following paragraphs describe the unique and common effects the LCD Panel Assembly, TCON/HFR Board, and A-Board have on the displayed video concerning possible distortions. Knowing how each component affects the displayed video can be very helpful in troubleshooting a distorted video condition.
NOTES: Reference Appendix for picture examples of unique distortions for the LCD Panel, TCON/HFR Board, and the A-Board
WIDE Mode Button (Aspect Ratio) Troubleshooting MethodA quick test to determine if the A-Board, TCON/HFR, or LCD Panel is causing the distortion is to change the panel aspect ratio (or picture size).
-
CTV-61 26
AZ1K Chassis Models Overview
The aspect ratio can be easily changed using the WIDE key on the remote controller. If the distortion follows the video then the A-Board is causing the distortion. If the distortion remains stationary after changing the aspect ratio then the LCD Panel assembly is causing the distortion.
Unique Main Video Board (A-Board) or LVDS Cable EffectsA video distortion that has soft edges and/or is moving through the video is most likely caused by a defect in the video processing circuitry. All video processing circuitry is located on the A-Board. Therefore, replace the A-Board if the video distortion has soft edges and/or is moving through the video on the screen. Macro-Blocking (digital picture breakup) is a good example of this type of distortion. Be careful though, macro-blocking can also be caused by a weak RF signal when the TV is in the tuner mode.
Poor Picture Detail - Loss of overall picture detail. A loss of information on the LVDS lines from IC400 will cause poor overall picture detail.
Abnormal Picture Size or Geometry- The video signal scaler circuit is located on the main video board A-Board. Therefore, if either the picture size or geometry is abnormal the A-Board is defective. Only the A-Board can cause such a distortion.
Color Distortion - A color distortion can be caused by a defective IC400 or LVDS cable. The individual color signals are spread out over the LVDS twist pair wires. For example, the Red signal may be broken up into three components and sent over three different LVDS twisted pairs. Therefore, this distortion will display as a poor reproduction of a particular color not an overall loss of one color. Use a Red, Green, and Blue raster generator to conrm a poor reproduction of a single color.
Loss of a Single Color - A loss of a single color can only be caused by a defective MT5388 (IC400). Use a Red, Green, and Blue raster generator to conrm a complete loss of a single color.
RF Signal Distortion - A weak video signal from the antenna or cable connection can cause RF video distortions. The signal strength of the Digital Signals can be checked in the USER menu. Go to the Product Support and Signal Diagnostic item to check signal strength and errors. NOTE: This is only for digital channels. No information will display for analog channels. The SNR should be in the range of 25db to 30db and there should be zero Errors.
WIDE Mode Button
Signal Diagnostics Screen
WIDE Mode Function
Product Support
Signal Diagnostics
-
CTV-61 27
AZ1K Chassis Models Overview
Unique TCON/HFR Board Effects 2 Vertical Transparent Colored Bar- The bar will be
approximately 2" because this is the area that is controlled by a single drive IC that is located across the top of the LCD Panel assembly.
Video Timing - The Video Timing distortion may appear as a double image or ghosting type distortion.
Loss of Half Screen Video - Half the screen will have live video and the other half will be a white raster.
Half or Full Screen Video Distortion - In this case, the key distinguishing factor is the presence of undistorted video behind the color distortion. The distortion is basically an overlay (transparent color half-screen or bar) in front of the good video coming from the A-Board.
White or Colored Blooming - The bloomings may come down from the top of the screen and vary in size.
GAMMA Irregularity - A GAMMA distortion will appear as a overall brightness problem or a localized area color distortion.
Unique LCD Panel Assembly Effects Line(s) of Pixels (Fixed Position) - Poor physical connection
(or bonding) between the LCD Panel and the ex cables will cause a loss of line(s) of pixels. The pixel drive lines can be open (no drive) or shorted (drive all the time). Depending on the type of failure the line(s) or pixel(s) will be black, white, or colored (red, green, or blue). These lines and pixels will also be very sharp in detail.
Random Line(s) of Pixels (Random Movement) - The TCON board controls the charging and timing of the pixels. If the TCON Board is partially defective random lines and/or pixels will be seen ashing across the screen. These lines and pixels will be very sharp in detail, like a specic line of pixels are randomly turned off and on.
2 Vertical Solid White or Black Bar- The bar will be approximately 2" because this is the area that is controlled by a single drive IC that is located across the top of the LCD Panel assembly.
Horizontal Bar- Any horizontal bar of any color will be caused by a defective LCD Panel assembly
Common Main Video Board (A-Board) and LCD Panel Assembly Effects
White Balance (WB) Irregularity - A WB irregularity will show up as an overall poor reproduction of white. A white raster can be used to determine if a WB or gamma irregularity has occurred. WB will cover the complete picture, where as, gamma will be in specic zones or specic color areas in the picture. WB adjustment data is stored in the EEPROM IC4302 on the A-Board. The WB data stored in IC4302 is set to the middle value of the data span. The TCON/HFR Board also contains WB data, which is specically set for the associated LCD Panel.
GAMMA Irregularity - Gamma Correction affects the overall picture brightness level and individual color (RGB) brightness levels. Gamma adjustment data is stored in the EEPROM IC4702 The TCON/HFR Board also contains GAMMA data, which is specically set for the associated LCD Panel. The data may become corrupted causing irregular gamma adjustment. Therefore, a gamma distortion can show up as a color brightness irregularity in specic zones or specic color areas in the picture, as well as an irregularity in overall picture brightness.
-
CTV-61 28
AZ1K Chassis Models Overview
A-Board
IC400MTK5388
(HDCP)
LCD Panel Assembly
TCON/HFR
LCD Panel
CCFL BacklightSystem
CN41521/
49
IC4302NAND FLASH
User DataWhite BalanceGAMMA
User Menu Service Mode
IC303Sub
Micro
4/
10LVDS 12V
LCD Panel
LVDS Cable
RF Input
Video 2 (Composite / S-Video)
Video 1 (Component & Composite)
PC Input
HDMI IN 1
HDMI IN 2
HDMI IN 3
IC6601HDMISwitch(EDID)
Video 3 (Component)
USB 2.0
TCON 12V 12V
From Power Supply Board
HDMI IN 4
TM701NTSC/ATSC
Tuner
Video System Block Diagram
VIDEO SYSTEM FIGURE 2-8
-
CTV-61 29
AZ1K Chassis Models Overview
Audio Symptom TroubleshootingReference Figure 2-9
Normal OperationThe HDMI digital audio signal is rst applied to the HDMI Receiver/Switch IC6601 and then to the MT5388 on the A-Board.
The RF input is rst applied to the Tuner and then to the IC400. The Tuner outputs the ATSC and NTSC signals as an IF signal to IC400.
All other audio inputs are applied directly to IC400. The MT5388 IC400. outputs the audio signal as a SPDIF signal for the Optical output. The FIXED analog audio output passes through an amplier IC8301 and then is applied to CN8301.
The main speaker audio comes from IC400 and passes through amplier IC8151 and then to CN8151 and CN8152 speaker connections..
The AU12V from the G2LE, G2HE, or GD2-Board is the power supply for the audio output amplier IC8151.
IMPORTANT:
Conrm the TV has the most recent Software Version installed. Go to the User Menu for the present TV software revision and the ASC web site for the most recent software version.
Failure SymptomsThe rst step when a Missing or Distorted Audio defect occurs is to determine if audio is missing or distorted on all audio input sources or only on one or a select number of audio input sources.
Input Status:
Missing or Distorted Audio on All Inputs Missing or Distorted Audio on Individual Inputs
Missing or Distorted Main Speaker Audio - All Inputs
In this case, the most likely defective is the A-Board. Before you replace the A-Board perform the following test procedures to conrm the actual defective component.
1) Check for audio at the Analog FIX or DIGITAL Audio Outputs
a) No or Distorted Audio (Replace A-Board)
b) Audio Present & Undistorted. Go to Step 2
2) Check for AU12V at CN201/pin 1 on A-Board
a) No AU12V - Check connections between the Power Supply board and the A-Board
b) AU12V Present replace A-Board
Missing or Distorted Main Speaker Audio - Individual InputsIf only one or a select number of input sources are experiencing a problem, then the individual inputs must be checked separately. The external devices and their associated cables connected to the faulty input should be checked rst.
Substitute a known good device and cable on the suspected faulty input. Connect the device and cable at separate times to determine if the device or cable is causing the problem. Replace the device or cabling if found to be defective. However, if the external device and cables are okay, then the next step is to replace the common board or module associated with that particular input source.
For example, consider the symptom of all HDMI inputs are faulty. Logically the only device that could cause this symptom is the HDMI switcher IC6601 on the A-Board. In this case, replace the A-Board.
-
CTV-61 30
AZ1K Chassis Models Overview
Video 2 (Composite/S-Video)
LR Audio
A-Board
IC400MTK5388
(HDCP)
HDMI IN 1
Video 1 (Component & Composite)
RF Input
PC IN
LR Audio
HDMI IN 2
Video 3 (Component)
IC6601HDMI
Receiver/Switch(EDID)
TM701NTSC/ATSC
Tuner
Digital Audio
R
L
FIXED Analog Audio Output
Digital Audio Output (Optical)
LR Audio
SPDIF
Audio IN (DVI)LR Audio
LR Audio
LR Audio
I2S
F1
CN8302
CN8301
AU12V
CN6401 (32", 40")CN6150 (46") CN201
AC
HDMI IN 3
HDMI IN 4
IC8151 Output
Amplifier
LR Audio
11
USB 2.0
G2LE-Board (32")G2HE-Board (40")GD2-Boad (46")
IC8301Amp
CN8151
PS6401
CN8152
IF
Audio System Block Diagram
AUDIO SYSTEM FIGURE 2-9
-
CTV-61 31
Section 3 - Service Mode
SERVICE MODE FIGURE 3-1
Service Mode AccessService Mode Access
Display > 5 > Volume + > Power
Total operation time by hour (max 99999 )
Boot count (max 99999 )
Panel operation time by hour (max 99999 )(Reset Panel operation Time , Press 7 > 0 keys )
Reset Self Check, Press 8 > 0 keys
-
CTV-61 32
Section 4 - Triage & Troubleshooting Flowcharts
Triage Flowchart
Triage Flowchart A (AZ1K 32", 40", & 46" Models)
StartTriage
Is Video Missing
or Distorted ?
No
Yes
No
No
No
Yes
Yes
Yes
GO TOPower-ON
TroubleshootingFlowchart B
GO TOProtection Mode Troubleshooting
Flowcharts C1, 2, 3, 4
GO TOMissing or Distorted
Video TroubleshootingFlowchart D
GO TOMissing or Distorted
Audio TroubleshootingFlowchart E
No Problem Found
Unit Fully Operational
A
Is RED
Standby LEDON?
Is Standby LED
Flashing Red?
Is Audio Missing or
Distorted?
Go to No Standby LED
Triage Sheet Replacement Parts
Go to Protect Blink Code
Triage Sheet Suggested Parts
Go to Audio
Triage Sheet Suggested Parts
Go to Video
Triage Sheet Suggested Parts
-
CTV-61 33
Triage & Troubleshooting Flowcharts
Power-ON Troubleshooting Flowchart B (AZ1K 32", 40", 46" Models)
Unit will Not Power-ON
(All Models)
Is Standby LED
illuminatedRED?
What is the State of the
Power & Standby LEDs?
No
YesPower Glows Steady Green
No
Press TV & Remote
POWER Button
Initial Power-ON OK Troubleshoot Video,
Backlight, Panel, or Audio Problem
Check STBY 3.3V at CN6401/pin 1(In STBY Mode)
B
Confirm Unit is securely plugged into an active AC Outlet
Is 110VAC Present
at CN6101?
Repair AC Outlet or Replace AC-Power Cord
OK
Yes
GO TOFlowCharts C1, 2, 3
Protection Modes
Standby Red LED Blink Pattern
Confirm Remote Control Operation
Check Main Fuse F6101
(0 ohms)
Is voltage 3.3V
Present?
No
Yes
NOTE: Confirm all connections between circuit boards before replacing
Is Fuse Open?
No
Yes
IP3N-Board
Is voltage 3V
Present?
No
Yes
Check AC_OFF_DET
at CN6401/pin 2
Is voltage 12V
Present?
No
Yes
Replace G2LE-BoardG2HE-BoardGD2-Boad
Check SW_12V at CN6401/pin 9(In STBY Mode))
Check Power_ON at CN6401/pin 3(In STBY Mode)
Is voltage 3.3V
Present?
Replace A-Board
Replace A-Board
Cycle AC power while checking for 12V. Unplug and Plug AC Power Cord .
Yes
No
Replace G2LE-BoardG2HE-BoardGD2-Boad
CN6003 - 46"
F6001 - 46"
CN6150 - 46"
CN6150 - 46"
CN6150 - 46"
CN6150 - 46"
Replace G2LE-BoardG2HE-BoardGD2-Boad
Power-ON Troubleshooting Flowchart
-
CTV-61 34
Triage & Troubleshooting Flowcharts
Protection Mode 2X, 3X, & 4X Troubleshooting Flowchart
Protection Mode Troubleshooting Flowchart C 1 (AZ1K 32" & 40" Models)
Unit Shuts OFFRED LED Blinking
C1
2X Blink PatternAU12V LVP & SW12V OVP
~12V
Check AU12V at CN6401/pin 4
*Before Shutdown
NOTES:1) All Red Blink patterns will occur on the Front Panel Red Standby LED2) All voltage are measured prior to unit shutdown3) Confirm all connections between circuit boards before replacing
Yes
No
(>) Greater Than(~) Approximately (Does not exceed)
Replace A-Board
3X Blink PatternAudio
>12V
Check SW12V at CN6401/pin 9
*Before Shutdown
Is Voltage
~12V or >12V?
Is voltage 12V
Present?
Yes
Check Speakers & Connections
Do Speakers Measure 8 ohms
?
No Replace Speaker(s)
Replace A-Board
Replace
G2LE-BoardG2HE-BoardGD2-Boad
Replace G2LE-BoardG2HE-BoardGD2-Boad
CN6150 - 46"
CN6150 - 46"
4X Blink PatternBalancer
46" Models ONLY
Check LD Volatge
CN6702/pin 5
Is voltage 0V or 12VPresent?
Replace LCD Panel
0V
12V
Replace G2LE-BoardG2HE-BoardGD2-Boad
Is Problem Solved?
Problem Sloved
Replace A-Board
No
Yes
-
CTV-61 35
Triage & Troubleshooting Flowcharts
Protection Mode 5X & 6X(32, 40) Troubleshooting Flowchart
5X Blink PatternTCON/HFR Error
Is connection
OK?
Repair Connection
No
Yes
C2NOTES:
1) All Red Blink patterns will occur on the Front Panel Red Standby LED2) All voltage are measured prior to unit shutdown3) Confirm all connections between circuit boards before replacing
Check LVDS connection between
LCD Panel (TCON) & A Brds
Replace A-Board
Check TCON 12V supply CN6403/pins 1 & 2
Is 12V Present
?
Replace TCON/HFR Brd
No
Yes
Protection Mode Troubleshooting Flowchart C 2 (AZ1K 32", 40", 46" Models)
Unit Shuts OFFRED LED Blinking
Is Issue
Resolved?
Issue Resolved
Yes
No
Is voltage
24V Before Shutdown
?
Yes
No
Check 24V at CN6402/pin 3
*Before Shutdown
Check Inverter HV Outputs
*Before Shutdown
Is Backlight ON Before Shut
Down?
Yes
Are Select outputs
missing?
No
Yes
No
Replace LCD Panel Assembly
Check Backlight-ONsignak at
CN201/pin 12*Before Shutdown
Is voltage
3V Before Shutdown
?
Replace A-Board
Yes
No
Replace Inverter Board
Replace Inverter Board
Is SONY logo Displayed and Tones Heard?
Check for Open or Short
Check Dimmer signal at CN201/pin 13
*Before Shutdown
Is voltage
1V to 3V Before Shutdown
?
Check for Short
Replace A-Board
Replace G2LE-BoardG2HE-Board
6X Blink Pattern(No Backlight)
CN6151 - 46"
Replace G2LE-BoardG2HE-BoardGD2-Boad
32" & 40" Models ONLY
-
CTV-61 36
Triage & Troubleshooting Flowcharts
Protection Mode 6X(46) & 7X Troubleshooting Flowchart
Protection Mode Troubleshooting Flowchart C 3 (AZ1K 32", 40", 46" Models)
C3
7X Blink PatternTemperature Error
Clear unit ventilation areas and confirm adequate local
room temperature
NoDoes unit still shutdown (7X)?
Issue Resolved
Yes
Does unit Shut-Down
Immediately after Power ON
?
Yes
No
Temperature ThresholdAmbient 80C
NOTES:1) All Red Blink patterns will occur on the Front Panel Red Standby LED2) All voltage are measured prior to unit shutdown3) Confirm all connections between circuit boards before replacing
Replace A-Board
Unit Shuts OFFRED LED Blinking
Is voltage
HV Before Shutdown
?
Yes
Check HV at CN6704 & CN6705*Before Shutdown
No
Check Backlight-ONsignak at
CN201/pin 12*Before Shutdown
Is voltage
3V Before Shutdown
?
Replace A-Board
Yes
No
Check for Open or Short
Check Dimmer signal at CN201/pin 13
*Before Shutdown
Is voltage
1V to 3V Before Shutdown
?
Check for Short
Replace A-Board
Replace GD2-Board
Replace GD2-Board
No
Yes
6X Blink Pattern(No Backlight)46" Models ONLY
-
CTV-61 37
Triage & Troubleshooting Flowcharts
Video Troubleshooting Flowchart
Missing or Distorted Video
Is Video Missing or Distorted on All
Inputs?
No
Yes No
Yes
Can User Menu be
Displayed?
No
D
All Video Inputs : Composite Component HDMI PC IN ATSC/NTSC (Tuner) USB
Is Video Missing or Distorted
?
Missing
Distorted
Is Single Pixels
or Complete Lineof Pixels missing?
Yes
No
Yes
NOTE: Confirm all connections between circuit boards before replacing
Is Distortion Present in User Menu
OSD?
No
Yes
Is External Device & connection OK
?
Repair External Device
Check External Device and ConnectionsSwap Devices and
connections
Skew (or Rock) the LVDS connector from its socket at the TCON/HFR Brd.
(Reference TM for Details)
Are Flashes of color
displayed?
Yes
No
No
Check LVDS cable for Physical Damage
Replace LCD Panel
Replace TCON/HFR Board
Replace LVDS CableIf Damaged
Replace A-Board
Video Troubleshooting Flowchart D (AZ1K 32", 40", 46" Models)
Replace A-Board
Replace A-Board
Is Backlight ON
?
Go To Flowchart C2
Replace A-Board
Yes
Or check LVDS cable Video & Clock Signal Levels atCN4152/pins 1 - 49 using an Oscilloscope .
TM Training Manual
Sharp Horizontal or Vertical Lines
Cable OK
Does Distortion follow
picture size when changing
WIDE mode?
Perform WIDE Mode Test(Reference TM for Dertails)
Replace A-Board
Replace TCON/HFR Board
No
Yes
-
CTV-61 38
Triage & Troubleshooting Flowcharts
Audio Troubleshooting Flowchart
NOTE: Confirm all connections between circuit boards before replacing
Is Audio Present?
CheckFix Audio Output
No
Missing or Distorted Audio(Speaker Outputs )
Is Audio Missing or Distorted
on All Inputs ?
No
Yes
Yes
E
Check Speaker Resistance at
CN8301 & CN8302 (across Speakers)
& Connections
8 ohms &
Connections OK?
No
CheckVoltage from Power Supply
at CN6401/pin 4
Is 12V Present?
Yes
Yes
Replace Speaker(s)
No
No
YesIs
External Device & connection OK
?
Repair External Device
Check External Device and ConnectionsSwap Devices and
connections
All Video Inputs : Composite Component HDMI PC IN ATSC/NTSC (Tuner) USB
Audio Troubleshooting Flowchart E (AZ1K 32", 40", 46" Models)
Replace A-Board
Replace A-Board
Replace A-Board
Replace G2LE-BoardG2HE-BoardGD2-Boad
CN6150 - 46"
-
CTV-61 39
Appendix
LCD Panel Distortion Pictures
2' Solid Black Bar Distortion Timing Distortion
Double Image Distortion Ghosting Distortion
2" Solid White Bar Distortion Sharp Lines & Missing Pixels
The following distortions and anomalies where xed by replacing the LCD Panel.
-
CTV-61 40
Appendix
TCON/HFR Board Distortion Pictures
Large Blooming Distortion Two Small Blooming Distortions
GAMMA Type Distortion 2" Transparent Colored Bar Distortion
Complete Washout Distortion 2" Transparent Colored bar Distortion
The following distortions and anomalies where xed by replacing the TCON/HFR Board.
-
CTV-61 41
Appendix
2" White Bar w/ Random Colored Lines Exact Half-Screen Distortion
Complete Washout w/ Colored Lines
TCON/HFR Board Distortion Pictures ContinuedThe following distortions and anomalies where xed by replacing the TCON/HFR Board.
-
CTV-61 42
Appendix
Video Board Distortion Pictures
Green Carpet Raster Multi-Colored Carpet Raster
Text Bleed Lines Random Size Vertical Bars
Overall Red Tinting Solarization
The following distortions and anomalies where xed by replacing the Video Board.
-
CTV-61 43
Appendix
Video Board Distortion Pictures Continued
Partial Washout w/ Random Video Bar Overall Blue Tinting w/ Soft Vertical Lines
Green Raster Overall Green Tinting w/ Video Ghosting
Overall Red Tinting
The following distortions and anomalies where xed by replacing the Video Board.
-
and i.Link are trademarks of Sony Electronics
2007 Sony Electronics, Inc.EMCSA - A Service Company
16530 Via EsprilloSan Diego, CA 92127
Reproduction in whole or part without written permission is prohibited. All rights reservedCTV610110 03/30/10
Section 1 - AZ1K Chassis Models OverviewAZ1K Chassis Models CoveredModel IntroductionAV Input & Output DescriptionsRF InputComposite Video & Audio InputsComponent/Composite Video & Audio InputsHDMI/DVI Video Input and DVI Video
PC Video & Audio Input (and DVI Audio)USB 2.0 Side Connection - Photos & Music
Audio OutputsFixed Analog Audio OutputDigital Audio Output (Optical)
32 & 40 Models Overall PCB Block Diagram46 Models Overall PCB Block DiagramPCB and Component DescriptionsA-Board G2LE-Board (32") or G2HE-Board (40")GD2-Board (46")
Backlight Inverter Board (32" & 40")H2-BoardSwitch UnitLCD Panel Assembly
Section 2 - Troubleshooting ProceduresPower Symptom TroubleshootingNormal OperationFailure SymptomsNo Power/Dead Set (No RED Standby LED)
32 & 40 Power Supply System Block DiagramG2LE-Board & G2HE-Board Connector Diagram46 Power Supply System Block DiagramGD2-Board Connector DiagramProtection Mode Symptom TroubleshootingFailure Symptoms2X Blink - Main Power Error3X Blink- Audio Error4X Blink - Balancer Failure (46 Models ONLY)5X Blink - TCON & HFR Failure6X Blink - Backlight System Failure (32 & 40 Models)6X Blink - Backlight System Failure (46 Models)7X Blink - Temperature Failure
32 & 40 Models Protection Mode System Block Diagram46 Models Protection Mode System Block DiagramAll Models Power Board Protection Circuits Block DiagramVideo Symptom TroubleshootingNormal OperationTroubleshootingMissing or Distorted Video (Individual Inputs)Missing Video (All Inputs)Skewing LVDS Connector Troubleshooting Method
Distorted Video (All Inputs)WIDE Mode Button (Aspect Ratio) Troubleshooting MethodUnique Main Video Board (A-Board) or LVDS Cable EffectsUnique TCON/HFR Board EffectsUnique LCD Panel Assembly EffectsCommon Main Video Board (A-Board) and LCD Panel Assembly Effects
Video System Block DiagramAudio Symptom TroubleshootingNormal OperationFailure SymptomsMissing or Distorted Main Speaker Audio - All InputsMissing or Distorted Main Speaker Audio - Individual Inputs
Audio System Block Diagram
Section 3 - Service ModeService Mode Access
Section 4 - Triage & Troubleshooting FlowchartsTriage FlowchartPower-ON Troubleshooting FlowchartProtection Mode 2X, 3X, & 4X Troubleshooting FlowchartProtection Mode 5X & 6X(32, 40) Troubleshooting FlowchartProtection Mode 6X(46) & 7X Troubleshooting FlowchartVideo Troubleshooting FlowchartAudio Troubleshooting Flowchart
AppendixLCD Panel Distortion PicturesTCON/HFR Board Distortion PicturesTCON/HFR Board Distortion Pictures ContinuedVideo Board Distortion PicturesVideo Board Distortion Pictures Continued