sony dvp-s325 dvp-s525d dvp-s725d

DVP-S325/S525D/S725DRMT-D108O/D108P/D109P/D111O/D111PAEP ModelDVP-S325/S525D/S725D

SERVICE MANUAL

East European Model North European ModelDVP-S325/S525D/S725D

Russian ModelDVP-S325/S525D/S725D

Australian ModelDVP-S525D/S725D

E ModelDVP-S725DPhoto: DVP-S725D

SPECIFICATIONSCD/DVD playerLaser Signal format system Semiconductor laser PAL/(NTSC) VIDEO OUT (1, 2) (S725D) S VIDEO OUT (S325/S525D) S VIDEO OUT (1, 2) (S725D) Phono 1.0 Vp-p jacks 4-pin Y: 1.0 Vp-p mini DIN C: 0.3 Vp-p (PAL) C: 0.286 Vp-p (NTSC) phono Y: 1.0 Vp-p jacks CB/B-Y, CR/R-Y: 0.7 Vp-p Phone 12 mW jack Phono 2 Vrms jacks (at 50 kilohms) 75 ohms, sync negative 75 ohms, sync negative 75 ohms terminated

Audio characteristicsFrequency response DVD (PCM 96 kHz): 2 Hz to 44 kHz (1 dB)* (S325/S525D) DVD (PCM 96 kHz): 2 Hz to 44 kHz (0.5 dB)* (S725D) DVD (PCM 48 kHz): 2 Hz to 22 kHz (0.5 dB) CD: 2 Hz to 20 kHz (0.5 dB) More than 110 dB (LINE OUT (AUDIO) connectors only) (S325/S525D) More than 110 dB (AUDIO OUT connector only) (S725D) Less than 0.0025% More than 100 dB (DVD) More than 98 dB (CD) Less than detected value (0.001% W PEAK) Output level 2 Vrms (at 50 kilohms) 2 Vrms (at 50 kilohms) 18 dBm Load impedance Over 10 kilohms

Signal-to-noise ratio

Harmonic distortion Dynamic range Wow and flutter

COMPONENT VIDEO OUT (Y, CB/B-Y, CR/R-Y) (S725D) PHONES (EXCEPT S325) 5.1CH OUTPUT (EXCEPT S325)

75 ohms, sync negative 75 ohms 32 ohms Over 10 kilohms

GeneralPower requirements Power consumption Dimensions (approx.) Mass (approx.) 220 240 V AC, 50/60 Hz 16 W (S325) 17 W (S525D) 22 W (S725D) 430 95 305 mm (w/h/d) incl. projecting parts 3.3 kg (S325) 3.4 kg (S525D) 4.0 kg (S725D) 5C to 35C Continued on next page

Outputs and inputsJack type Phono jacks Phono jacks Optical output connector Phono jack Phono jacks

LINE OUT (AUDIO) (S325/S525D) AUIO OUT (S725D) DIGITAL OUT (OPTICAL) DIGITAL OUT (COAXIAL) LINE OUT (VIDEO) (S325/S525D)

Over 10 kilohms Wave length: 660 nm Operating temperature

0.5 Vp-p 1.0 Vp-p

75 ohms terminated 75 ohms, sync negative

CD/DVD PLAYERMICROFILM

Operating humidity

5% to 90%

Supplied accessories Audio/Video connecting cord (1) S video cable (1) Remote commander (remote) RMT-D108O (1) (S525D: Australian) Remote commander (remote) RMT-D108P (1) (S525D: EXCEPT Australian) Remote commander (remote) RMT-D109P (1) (S325) Remote commander (remote) RMT-D111O (1) (S725D: Australian) Remote commander (remote) RMT-D111P (1) (S725D: EXCEPT Asutralian) Size AA (R6) batteries (2) DVP-S325/S525D: * The signals from LINE OUT (AUDIO) connectors and 5.1 ch L, R connectors (S525D only) are measured. When you play the PCM sound tracks with 96 kHz sampling frequency, the output signals from the DIGITAL OUT (OPTICAL, COAXIAL) are converted to 48 kHz (sampling frequency). DVP-S725D: * The signals from AUDIO OUT connectors and 5.1 ch L, R connectors are measured. When you play the PCM sound tracks with 96 kHz sampling frequency, the output signals from the DIGITAL OUT (OPTICAL, COAXIAL) are converted to 48 kHz (sampling frequency). Design and specifications are subject to change without notice.

WARNING!! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 25 cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. CAUTION: The use of optical instrument with this product will increase eye hazard. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

CLASS 3B LASER LUOKAN 3B LASER LASERKLASS 3B

SAFETY CHECK-OUTAfter correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are pinched or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified.

2

TABLE OF CONTENTSSection Title Page Section Title Page

Service Note ............................................................................ 4

1.

GENERALGetting Started .............................................................. Playing Discs ................................................................. Using Various Functions with the Control Menu ........... Settings and Adjustments ............................................. 1-1 1-4 1-6 1-12

2.2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 2-7. 2-8. 2-9. 2-10. 2-11. 2-12.

DISASSEMBLY2-1 2-1 2-1 2-1 2-2 2-2 2-2 2-2 2-3 2-3 2-3 2-3 2-4 2-5

Case Removal ............................................................... MB-82/85 Board Removal ............................................. Power Block Removal ................................................... ER-4/5 Board Removal (EXCEPT Australian) .............. AU-209/212 Board Removal (S325/S525D) ................. AU-210/211 Board Removal (S725D) ........................... Tray Cover Removal ..................................................... Front Panel Removal .................................................... Mechanism Deck Removal ........................................... Tray Removal ................................................................ Optical Pick-up Removal ............................................... Belt, Loading Motor (M001), MS-29/TK-51/54 Board Removal .................................. 2-13. Internal Views ................................................................ 2-14. Circuit Boards Location .................................................

AU-211 Printed Wiring Board ........................................ 4-57 AU-211 (AUDIO) Schematic Diagram ........................... 4-61 AU-211 (VIDEO BUFFER) Schematic Diagram ........... 4-63 AU-212 Printed Wiring Board ....................................... 4-65 AU-212 (AUDIO) Schematic Diagram .......................... 4-67 AU-212 (VIDEO BUFFER) Schematic Diagram ........... 4-69 ER-4 Printed Wiring Board ............................................ 4-71 ER-4 (EURO AV1) Schematic Diagram ........................ 4-73 ER-4 (EURO AV2) Schematic Diagram ........................ 4-75 ER-5 Printed Wiring Board ............................................ 4-77 ER-5 (EURO AV1) Schematic Diagram ........................ 4-81 ER-5 (EURO AV2) Schematic Diagram ........................ 4-83 FL-98/101 Printed Wiring Board ................................... 4-87 FL-99/100 Printed Wiring Board ................................... 4-89 FL-98/99/100/101 (FUNCTION SWITCH) Schematic Diagram ....................................................... 4-93 FL-98/99/100/101 (IF CON) Schematic Diagram ......... 4-95 SW-314/315/316/317, FR-147/148/149/150 Printed Wiring Boards ................................................... 4-97 SW-314/315/316/317, FR-147/148/149/150 Schematic Diagram ....................................................... 4-99 HP-108/109/110/111 Printed Wiring Boards and Schematic Diagram ..................................................... 4-101 RY-12 Printed Wiring Board and Schematic Diagram ..................................................... 4-103 HS-030SH Printed Wiring Board ................................ 4-105 HS-030SH Schematic Diagram .................................. 4-107

3.3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8. 3-9. 3-10.

BLOCK DIAGRAMSOverall Block Diagram .................................................. RF/Servo Block Diagram .............................................. Signal Process Block Diagram ..................................... Video Block Diagram ..................................................... System Control Block Diagram ..................................... Audio (1) Block Diagram ............................................... Audio (2) Block Diagram ............................................... Audio (3) Block Diagram ............................................... Interface Control Block Diagram ................................... Power Block Diagram .................................................... 3-1 3-3 3-5 3-7 3-9 3-11 3-13 3-15 3-17 3-19

5.5-1.

IC PIN FUNCTION DESCRIPTIONSystem Control Pin Function (MB-82/85 Board IC202) ............................................... 5-1

6.6-1. 6-2. 6-3. 6-4. 6-5. 6-6. 6-7. 6-8. 6-9.

TEST MODEGeneral Description ...................................................... 6-1 Starting Test Mode ........................................................ 6-1 Syscon Diagnosis .......................................................... 6-1 Drive Auto Adjustment .................................................. 6-5 Drive Manual Operation ................................................ 6-7 Mecha Aging ................................................................. 6-9 Emergency History ........................................................ 6-9 Version Information ....................................................... 6-10 Video Level Adjustment ................................................ 6-10

4.

PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMSFrame Schematic Diagrams .......................................... FRAME (1) Schematic Diagram .................................... FRAME (2) Schematic Diagram .................................... FRAME (3) Schematic Diagram .................................... Printed Wiring Boards and Schematic Diagrams ......... TK-51/54 Printed Wiring Board ..................................... TK-51/54 Schematic Diagram ....................................... MS-29 Printed Wiring Board and Schematic Diagram ....................................................... MB-82/85 Printed Wiring Board .................................... MB-82/85 (AV DECODER) Schematic Diagram ........... MB-82/85 (SDRAM) Schematic Diagram ..................... MB-82/85 (SERVO DSP) Schematic Diagram ............. MB-82/85 (DRIVE) Schematic Diagram ....................... MB-82/85 (ARP) Schematic Diagram ........................... MB-82/85 (SYSTEM CONTROL) Schematic Diagram ....................................................... MB-82/85 (HGA) Schematic Diagram ........................... MB-82/85 (CLOCK GENERATOR, AUDIO DSP, V EQ/NR) Schematic Diagram ...................................... MB-82/85 (DAC) Schematic Diagram ........................... MB-82/85 (BIAS) Schematic Diagram .......................... AU-209 Printed Wiring Board ....................................... AU-209 (AUDIO) Schematic Diagram .......................... AU-209 (VIDEO BUFFER) Schematic Diagram ........... AU-210 Printed Wiring Board ....................................... AU-210 (AUDIO) Schematic Diagram .......................... AU-210 (VIDEO BUFFER) Schematic Diagram ........... 4-3 4-3 4-5 4-7 4-9 4-9 4-13 4-15 4-17 4-21 4-23 4-25 4-27 4-29 4-31 4-33 4-35 4-37 4-39 4-43 4-45 4-47 4-49 4-53 4-55

4-1.

7.7-1. 1. 7-2. 1. 2. 3. 4. 5. 6. 7. 8. 9. 7-3.

ELECTRICAL ADJUSTMENTPower Supply Adjustment ............................................. HS030SH Board ............................................................ Adjustment of Video System ......................................... Video Level Adjustment ................................................. S-terminal Output Check ............................................... Checking Component Video Output B-Y ...................... Checking Component Video Output R-Y ...................... Checking Component Video Output Y .......................... Checking RGB Output R ............................................... Checking RGB Output G ............................................... Checking RGB Output B ............................................... Checking S Video output S-C ....................................... Adjustment Related Parts Arrangement ....................... 7-1 7-1 7-2 7-2 7-2 7-2 7-2 7-3 7-3 7-3 7-3 7-4 7-6

4-2.

8.

REPAIR PARTS LIST

8-1. Exploded Views ............................................................. 8-1 8-1-1. Case Assembly (S325/S525D) ................................ 8-1 8-1-2. Case Assembly (S725D) .......................................... 8-2 8-1-3. Front Panel Assembly .............................................. 8-3 8-1-4. Chassis Assembly .................................................... 8-5 8-1-5. Mechanism Deck Assembly ..................................... 8-7 8-2. Electrical Parts List ........................................................ 8-8

3

SERVICE NOTE1. DISASSEMBLY This set can be disassembled in the order shown below.

Set

Case (Page 2-1)

Tray Cover (Page 2-2)

MB-82/85 Board (Page 2-1)

ER-4/5 Board (EXCEPT Australian) (Page 2-1)

AU-210/212 Board (Australian) (Page 2-2)

Power Block (Page 2-1)

Front Panel (Page 2-2)

Mechanism Deck (Page 2-3)

AU-209/211 Board (EXCEPT Australian) (Page 2-2)

Tray (Page 2-3)

Optical Pick-up (Page 2-3)

TK-51/54 Board (Page 2-3)

Belt (Page 2-3)

Loading Motor (M001), MS-29 Board (Page 2-3)

4

2. NOTE ON REMOVE THE CASE1) Remove seven screws. (See Fig. 1) 2) Open the side of case. (See Fig. 1) 3) Remove the case as lift straight. (See Fig. 1)Case Two screws Three screws

4.

HOW TO SERVICE MB-82/85BOARD

1) Remove the case from the set. (Refer to 2-1) 2) Remove the MB-82/85 board. (Refer to 2-2) 3) Set the MB-82/85 board as shown in Fig. 3. Note: Do not disconnect wiring, except FMA-7/8/9.

MB-82/85 board Two screws grooves

Fig. 1 Fig. 3

3. DISC REMOVAL PROCEDURE (at POWER OFF)1) Insert a tapering driver into the aperture of the unit bottom, and move the lever of chuck cam in the direction of the arrow A. (See Fig. 2) 2) Draw out the tray in the direction of the arrow B, and remove a disc. (See Fig. 2)

Lever of chuck cam Aperture

B A Tray

Fig. 2

5

DVP-S325/S525D/S725D SECTION 1 GENERALThis section is extracted from DVP-S725D instruction manual (3-866-153-21).

1-1

1-2

1-3

1-4

1-5

1-6

1-7

1-8

1-9

1-10

1-11

1-12

1-13

1-14

1-15

1-16

1-17 E 1-17

DVP-S325/S525D/S725D SECTION 2 DISASSEMBLYNote: Follow the disassembly procedure in the numerical order given.

2-1. CASE REMOVAL4 Case 2 Two screws

2-3. POWER BLOCK REMOVAL2 Connector 3 Three connectors (CN101) (CN201, 202, 203) 1 Connector (CN102) (S725D) 4 Four screws (B3)

1 Three screws

3 Two screws5 Power block

2-2. MB-82/85 BOARD REMOVAL

2-4. ER-4/5 BOARD REMOVAL (EXCEPT Australian)1 Two flat cables (CN901, 902) 3 ER-4 board (S325/S525D) ER-5 board (S725D) 2 Four screws (B3)

4 Two flat cables 5 Flat cable (CN004, 007) (CN005) (S525D/S725D) 2 Two flat cables (CN002, 003) 1 Connector (CN011) 3 Connector (CN001) 7 Four screws (B3)

6 Flat cable (CN006) 8 MB-82 board (Australian) MB-85 board (EXCEPT Australian)

2-1

2-5. AU-209/212 BOARD REMOVAL (S325/S525D)3 Flat cable 4 Flat cable ! AU-209 board (CN302) (CN303) (S325/S525D: EXCEPT Australiran) (S525D: Australian) AU-212 board 9 Three screws (S525D: Australian) (B3) 5 Flat cable 2 Connector (CN301) (CN401)

2-7. TRAY COVER REMOVAL

4 Tray cover

3 Two claws

6 Screws (B3) (S525D: Australian) 7 Five screws (B3)

B 2 Pull the tray in the direction of the arrow B.

A

1 Insert a tapering driver into the aperture of the unit bottom, and move the lever of chuck cam in the direction of the arrow A.

1 Connector (CN201)

8 Two screws (B3) (S525D)

2-6. AU-210/211 BOARD REMOVAL (S725D)3 Two connectors 6 Three screws (CN301, 404) (B3) 2 Connector 4 Three flat cables (CN401) (CN402, 403, 405) 7 AU-210 board (Australian) AU-211 board (EXCEPT Australian)

2-8. FRONT PANEL REMOVAL4 Screw (B3) (S525D/S725D) 2 Connector (CN701) (S525D/S725D) 5 Two screws (B3) 6 Boss

1 Connector (CN203) 7 Boss

5 Nine screws (B3)

9 Claw

! Front panel 3 Flat cable (CN006)

1 Connector (CN407)

8 Claw

2-2

2-9. MECHANISM DECK REMOVAL3 Screw (B3)

2-11. OPTICAL PICK-UP REMOVAL5 Optical pick-up

4 Mechanism deck

2 Two flat cables (CN003, 004)

4 Three step screws 3 Remove the base unit holder in the direction of the arrow A.

A

1 Connector (CN001)

1 Two flexible board (CN001, 002)

2 Two claws

2-10. TRAY REMOVAL1 Two screws (BTP2.6 12)

2-12. BELT, LOADING MOTOR (M001), MS-29/TK-51/54 BOARD REMOVAL1 Belt 2 Two screws (B2.6 4)

2 Chuck assy

9 TK-51/54 board B 5 Flexible board (CN002) A

8 Claw

6 Flexible board (CN001) 7 Claw

4 Remove the tray in the direction of the arrow B.

3 Move the lever of chuck cam in the direction of the arrow A. 3 Three claws 4 Loading motor (M001), MS-29 board

2-3

2-13. INTERNAL VIEWS

DC motor (loading) 1-541-632-11

Optical pick-up (KHM-220AAA/J1RP) 8-820-081-03

2-4

2-14. CIRCUIT BOARDS LOCATION

FR-147 (S325/S525D: EXCEPT Australian) AU-209 (S325/S525D: EXCEPT Australian) FR-148 (S725D: Australian) AU-210 (S725D: Australian) FR-149 (S725D: EXCEPT Australian) AU-211 (S725D: EXCEPT Australian) FR-150 (S525D: Australian) AU-212 (S525D: Australian) TK-51 (IR/POWER SWITCH) (AUDIO) (Australian) TK-54 (EXCEPT Australian) (RF/SERVO) Power Block (HS-030SH) (SWITCHING REGULATOR) ER-4 RY-12 (S725D) (S325/S525D: EXCEPT Australian) (RELAY) ER-5 (S725D: EXCEPT Australian) (EURO AV)

HP-108 (S525D: EXCEPT Australian) HP-109 (S725D: Australian) HP-110 (S725D: EXCEPT Australian) HP-111 (S525D: Australian) (HEADPHONE)

MS-29 (LOADING)

MB-82 (Australian) MB-85 (EXCEPT Australian) (SIGNAL PROCESS/SERVO) FL-98 (S325/S525D: EXCEPT Australian) FL-99 (S725D: Australian) FL-100 (S725D: EXCEPT Australian) FL-101 (S525D: Australian) (FUNCTION SWITCH)

SW-314 (S525D: EXCEPT Australian) SW-315 (S725D: Australian) SW-316 (S725D: EXCEPT Australian) SW-317 (S525D: Australian) (SURROUND SWITCH)

2-5 E 2-5

DVP-S325/S525D/S725D SECTION 3 BLOCK DIAGRAMS3-1. OVERALL BLOCK DIAGRAMMB-82/85 BOARD(SEE PAGE 4-21~39) S525D/725D VIDEO Y, VIDEO B-Y, VIDEO R-Y S725D

AU-209/210/211/212 BOARD(SEE PAGE 4-45,47,53,55,61,63,67,69)

IC304 16M DRAM

IC402, 403 16M SDRAM

IC502 V EQ/NR

BASE UNITKHM-220AAA

TK-51/54 BOARD(SEE PAGE 4-13)

PDO 0-7

PDI 0-7

VIDEO BUFFER

COMPONENT VIDEO

OPTICAL DEVICE SD 0-7 IC001 DVD/CD PDIC RF DVD/CD RF AMP DIGITAL SERVO DVD RF, CD RF S525D/S725D

VIDEO V, VIDEO Y, VIDEO C

VIDEO BUFFER

VIDEO S VIDEO

IC303 ARP2 CDDOUT, CDDATA, CDBCK, CDLRCK

IC401 AV DECODER SPDIF, ACH12, ACH34, ACH56, BCK, LRCK

S325/ S525D: EXCEPT Australian S725D: EXCEPT Australian IC501 AUDIO DSP VIDEO R, VIDEO G, VIDEO B IC901-903 RY901-903 SW, BUFFER

EURO AV1 (RGB)-TV

RY904,905 FOCUS COIL IC801 TRACKING COIL FOCUS COIL/ TRACKING COIL/ TILT MOTOR DRIVE IC701 TILT MOTOR SERVO DSP IC601 HGA SYSTEM CONTROL Parallel BUS SW

EURO AV2

ER-4/5 BOARD(SEE PAGE 4-73,75,81,83)

IC202

IC204 1M SRAM

IC205 : S325/S525D IC206 : S725D 16M FLASH IC902 AUDIO LT, AUDIO RT LPF, GAIN CONTROL SPDIF

DIGITAL OUT

M

IC201 4K EEP ROM

AUDIO 2CH DAC

AUDIO OUT

SPINDLE MOTOR

MIC802

Serial BUS S725D

HP-108/109/ 110/111 BOARD(SEE PAGE 4-102) IC602 16M NAND-F S525D/S725D AUDIO L, R AUDIO LS, RS AUDIO C, LFE HEADPHONE AMP PHONES

SLED MOTOR

M

SPINDLE/SLED/ LOADING MOTOR DRIVE

M001 LOADING MOTOR

IC905-907

LPF

MND201 IC201 IF CON

5.1CH OUTPUT

AUDIO 5.1CH DAC

MS-29 BOARD(SEE PAGE 4-16)

+3.3V +5V A+12V M+12V

05

+3.3V +5V +12V 12V EVER5V

S725D AC10V

FL-98/99/100/101 BOARD(SEE PAGE 4-93,95)

SWITCH T901 JOG UNIT

S525D/S725D

FR-147/148/149/150 BOARD(SEE PAGE 4-99)

RY-12 BOARD(SEE PAGE 4-104)

SWITCH

SWITCH

HS-030SH BOARD(SEE PAGE 4-107)

SW-314/315/316/317 BOARD(SEE PAGE 4-99) 12V EVER5V SW REG

3-1

3-2

DVP-S325/S525D/S725D3-2. RF/SERVO BLOCK DIAGRAMBASE UNITKHM-220AAA

TK-51/54 BOARD(SEE PAGE 4-13)IC0011(DVD play) 200mV/DIV 100ns/DIV

IC001%(DVD play) 500mV/DIV 100ns/DIV

MB-82/85 BOARD(1/7)(SEE PAGE 4-25,27)IC001$(DVD play) 100mV/DIV 50ms/DIV IC001$(CD play) 500mV/DIV 50ms/DIV IC701^(DVD play) 500mV/DIV 50ms/DIV IC701^(DVD play) 100mV/DIV 5ms/DIV

1.5Vp-p 536mVp-p IC0011(CD play) 500mV/DIV 500ns/DIV IC001%(CD play) 500mV/DIV 500ns/DIV 180mVp-p IC001#(DVD play) 500mV/DIV 50ms/DIV 860mVp-p IC001#(CD play) 500mV/DIV 200ms/DIV

1.4Vp-p IC701^(CD play) 500mV/DIV 200ms/DIV

180mVp-p IC701^(CD play) 500mV/DIV 50ms/DIV

IC001880mVp-p

1.5Vp-p

OPTICAL DEVICE CN001 RF 7 1

DVD/CD RF AMP DIGITAL SERVO RF IP SIGO 54

CN003 17 RF+ 2

CN002

1.3Vp-p

1.7Vp-p

1.7Vp-p

860mVp-p

DVD RF CD RF

FE 40 9 10 16 17 8 11 15 18 13 TE 39 9 A-D 12 5 A2-D2 8 13 E-H 16 17 VC PI 29

9 8 7

FE TE PI

SIGNAL PROCESS10 11 12 68 ADC1 69 ADC0 67 ADC2 66 ADC3 65 ADC4 IC701 FG REF 22 LOCK MDS0 MDP0 (SEE PAGE 3-5)

DVD/CD PDIC

A-D

E-H

MIRR 26 TZC 32 VCI 33 SCLK SWD 43 SRD 46 SDEN FDCHG 27 HOLD2 42 DFT 31

3 5 6

MIRR TZC 2VC

16 14 13 5 8 4 15 2VC

21 TRIN 20 TRREF 23 FGIN

SERVO DSP +3.3V 74 81 VRBA, 84 DAB 0-3 93 96 IC702 (2/2) 7 5

VC

PD DVD/CD LD MODULE LD VR

4 2 5 Q001 LD DRIVE

19 PD 20 LD

SSCK, SSWD, 11 SSRD, SSCS 14 Q002 15 4 SSDFCT SSDFCTI

41 44

GIO 5-8

38 GIO 11 28 DFCTI

GIO 10 39 IC801 CN004 FOCUS COIL FCS 19 20 6 7 FCS 12 13 CN003 13 14 FOCUS COIL DRIVE 2 3 9 TRACKING COIL TRK 21 22IC001@(DVD play) 200mV/DIV 500ms/DIV IC001@(CD play) 200mV/DIV 20ms/DIV

FCSON XSDPIT XSDPRD XSDPWR XSDPCS HA0, 1

FCD

80 85

DAB 2,3 HINT 128 HRD 1 2 3 4 5

FCD Q801

TRD

92 97

DAB 0, 1

HWR HCS

4 5

TRK

14 15

11 12

TRACKING COIL DRIVE

5 6 7 20

TRD

TLTA,TLTB 48 49 IC702 (1/2) 3 1 SLDA, SLDB, 7 STVC 9 TILT MUTE FGMODE

GIO 1, 2

EA 0, 1

PWM 0-2X2/CLKIN

TILT MOTOR

M

TIA, TIB 10 13

15 18

TIA, TIB

1 4

15 18

TILT MOTOR DRIVE

23 26

TLTA, TLTB

50 GIO 0

26 IC803 (1/2)

RS

CN002

592mVp-p

448mVp-p

46 GIO 4

117 HD 0-7 120 122 125

HD8-15

108 N27MSDP

INLIMIT SENSOR

INLIM

2

8

INLIM

11 IC802

12 13

14

XSDPRST X3VRST Q802, 803 GAIN CONTROL SPDLSTOP SPGAIN

SYSTEM CONTROL(SEE PAGE 3-9,10)

SPINDLE MOTOR

M

SPM

8 9

13 14

SPM

5 6

15 16

SPINDLE MOTOR DRIVE

26

20 SLED MOTOR DRIVE 2 3 5 6 SLDA, SLDB, STVC

SLED MOTOR

M

SLA, SLB 4 7

9 12

SLA, SLB

7 10

11 14

XDRVMUTE

MS-29 BOARD(SEE PAGE 4-16) CN001 M001 LOADING MOTOR CN011 1 2 LDM 1 2 17 18 LOADING MOTOR DRIVE

9

LDMM/DMM LDMP/DMP +3.3V +5V IC803 (2/2) 5 7 8 1 2.5VC 2VC 1.6VC OCSW1 OCSW2 CKSW1

M

23

S001 TRAY SENSOR

4 6

OCSW 1, 2

4 6

OCSW 1, 2

10 3

S002 CHUCK SENSOR 05

3

CKSW1

3

CKSW1

3-3

3-4

DVP-S325/S525D/S725D3-3. SIGNAL PROCESS BLOCK DIAGRAMMB-82/85 BOARD(2/7)(SEE PAGE 4-21,23,29,35) IC502IC303!(DVD play) 500mV/DIV 100ns/DIV

S725D

V EQ/NR YO 0-7 HSYNC YI 0-7 IC304 16M DRAM IC402, 403 16M SDRAM CLK, CKE, DQML, DQMU, CS, WE, CAS, RAS

CLK 100 RST FLD SDI 93IC401%(RGB output model)

IC401%(RGB output model)

1.6Vp-p

11-18 PDO 0-7

60-67 PDI 0-7

720mVp-p(H) IC401% 1.0Vp-p(H) IC401% 720mVp-p(H) 1.0Vp-p(H)

97 98 31 29 HSYNCO SDOUT NR-SDOUT SENO NR-SENO FLDO

MD 00-15

DAD 0-11

1.6Vp-p

DVD RF CD RF

17 RFIN1 19 RFIN2 49 MDS0 52 MDP0

RF, SERVO(SEE PAGE 3-4) MDS0 MDP0 LOCK

97 98 SD 0-7 100 105

SD 0-7

38 43 45 46

HSYNCON

PDO 0-7

PDI 0-7

FLDO

136-139 141-144 146 147

154-157 159-162 164-167 169-172

148 150-152

DDT 0-15

MA 0-9

IC303!(CD play) 500mV/DIV 200ns/DIV

XMWR, XCAS, XRAS, XOE

105-108 110-113 115-118

DT 0-7 I

134 137 140 143 146 149 152 155

135 138 141 144 147 150 153 156

120-123 125 127 129-132

86-89 91-94

75-78 80-83 72 73 98 99

CS

G/Y OUT R/B-Y OUT B/R-Y OUT

58 54 57 65 61 62

VIDEO G/Y VIDEO R/B-Y VIDEO B/R-Y VIDEO V VIDEO Y VIDEO C

IC401%

IC401%(RGB output model)

IC303 ARP2

91 SDCK, SDEF, 47 93 XSHD, XSAK, XSRQ 51 96 CDDOUT, CDDATA, 107 CDBCK, CDLRCK 29 110 32

728mVp-p(H)

728mVp-p(H) IC401^

VIDEO(SEE PAGE 3-7)

COMP OUT Y OUT

DFCT NORF LOCK FWON MD2 MUTE XARPWR XARPRD XARPIT XARPCS XARPWT XCS2

55 DFCT 56 NORF 58 LOCK 59 FWON 113 MD2 111 MUTE 60 XWR 61 XRD 83 XINT 84 XCS 86 XWAT 166 167 193 194 196 198 202 CRPCLKIN HAD 0-21 I

IC401 AV DECODER1.2Vp-p(H) IC401^

C OUT

1.1Vp-p(H) IC401^

ACH12O S525D/ S725D ACH34O ACH56O LRCKO BCKO HD 0-15 S325 DO VREFI

21 22 23 25 26 27

816mVp-p(H)

ACLKIN

XRST

D 0-7

MCKI

A 0-7

SCKI

XRD XWRH XAVDIT XAVDWT DREQ0 DACK1 DREQ1

87 121 123

73-76 79-82

63-68 70 71

CLKI

XCS3

SCLKIN

RSTIN

103 19 36 160 163

168-170 172-178 180-187 189-192

2-5 7-10 12-15 205-208

70 RV401 VIDEO LEVEL ADJ

XARPRST

XAVDRST

33MARP

256FS30


DACK0 33M30 27M30

X57RST S525D/S725D LRCK S325 BCK

XARPRST XAVDRST X57RST S725D 33MARP 256FS30 33M30 27M30 27M57 S725D HA 0-7 CDDOUT, CDDATA, CDBCK, CDLRCK

ACH12 ACH34 ACH56

27M57

AUDIO 1(SEE PAGE 3-11)

HD 8-15

HA 0-21

HD 0-15

SPDIF1 CDDOUT CDDATA CDBCK CDLRCK S525D/S725D

HA 0-21

HD 0-15

05

3-5

3-6

DVP-S325/S525D/S725D3-4. VIDEO BLOCK DIAGRAMMB-82/85 BOARD(3/7)(SEE PAGE 4-21,37) S525D: Australian/ S725D

AU-209/210/211/212 BOARD(1/2)(SEE PAGE 4-45,47,53,55,61,63,67,69) IC302 :S725D IC303 :S525D: Australian CN004 VIDEO G/Y VIDEO R/B-Y 4 2 6 VIDEO G/Y VIDEO R/B-Y VIDEO B/R-Y 4 6 2 CN405 :S725D CN303 :S525D: Australian VIDEO BUFFER 2 4 7 1 15 13 10 J302 :S725D J303 :S525D: Australian Y CB/B-Y CR/R-Y COMPONENT VIDEO OUT

SIGNAL PROCESS(SEE PAGE 3-6)

VIDEO B/R-Y VIDEO V VIDEO Y VIDEO C

7 1

RGB EURO V/Y

1 7

Q439,440 RGB/YUV SW

IC301,321!

EURO V/Y YUV VIDEO B VIDEO R VIDEO G

1 7 6 2 4 CN406

Q301, 302 BUFFER

IC301,3214 2.4 Vp-p(H) 1.2Vp-p(H)

J505 :S525D :Australian VIDEO OUT1 VIDEO OUT2

J309 :S725D: EXCEPT Australian J506 :S325/S525D: EXCEPT Australian

S725D: EXCEPT Australian

J305 :S725D: Australian IC301 :S725D IC321 :S325/S525D VIDEO BUFFER 4 2 7 1 J306 :S725D: Australian 13 15 10 Y C S VIDEO OUT2 20 19 RY903 CN902 17 VIDEO V 17 3 151.8mVp-p(H)

CN005 1 3 5 VIDEO V VIDEO Y VIDEO C V MUTE 28 26 24 21

IC301,3212 1.1Vp-p(H)

Y C S VIDEO OUT1

J308 :S725D: EXCPET Australian J507 :S325/S525D: EXCEPT Australian

INTERFACE CONTROL(SEE PAGE 3-18)

V/Y IN V/Y OUT R/C OUT CN904

V MUTE

8


VS DISC/EXT RGB EURO V/Y S325/ S525D: EXCEPT Australian S725D: EXCEPT Australian

6 18

VS DISC/EXT

23 11 CN402 :S725D CN301 :S325/S525DIC301,3217

Q301, 302 :S725D Q321, 322 :S325/S525D DC ON/OFFIC301,3210

9 7 7 2 IC903 SWITCH Q914 RELAY DRIVE IC901 2 7 VIDEO BUFFER 2 4 7 1 MUTE Q917 15 13 10 RY901 7 4 9 2 1 8 4 2 1 8

15

VIDEO Y VIDEO C V MUTE VS DISC/EXT

11 3 7

G OUT B OUT

15 13 3 4 6

1

EURO AV1 (RGB)-TV

13 3 4 6 CN302 :S725D: EXCEPT Australian CN305 :S325/S525D: EXCEPT Australian

860mVp-p(H) IC301,321!

8 16

AV CONT OUT I OUT

2.0Vp-p(H)

IC902 SWITCH

CN901 VIDEO R VIDEO G VIDEO B 2 4 6

1 3

20 3 19 15

V IN V OUT R IN

EURO V/Y YUV

1 7

Q918 MUTE CONT S725D: EXCEPT Australian Q909,910 RELAY DRIVE CONT Q912 RELAY DRIVE

11

G IN CN903 EURO AV2

AUDIO 2 :S325/S525D(SEE PAGE 3-14)

7 RELAY DRIVE CONT RY902 9 7 Q906-908 AV CONT GEN 4 2 1 8 Q913 RELAY DRIVE 8 3

B IN

AUDIO 3 :S725D(SEE PAGE 3-16)

Q904,905 I SIG SW

16

I IN

AV CONT IN

ER-4/5 BOARD(1/2)(SEE PAGE 4-73,75,81,83)

Q901-903 I SIG GEN

05

S325/S525D: EXCEPT Australian/S725D: EXCEPT Australian

3-7

3-8

DVP-S325/S525D/S725D3-5. SYSTEM CONTROL BLOCK DIAGRAMS725D S325/S525D

MB-82/85 BOARD(4/7)(SEE PAGE 4-31,33,35) IC204 1M SRAM IC206 16M FLASH CS, WE, OE, UB, LB WE, RY/BY, OE, CE IC205 16M FLASH

HA 1-16

HA 1-20

HD 0-15

HD 0-15

HA 1-20

HA 0-5, 17-19

HD 8-15

HD 0-15

WE, OE, CE

HA 0-21

HD 0-15

SO0

SI1

SO1

SIGNAL PROCESS(SEE PAGE 3-5) HD 0-15

XFRRST

CS0L

SIO

SC0

SC1

HA 0-21

S725D IC602 16M NAND-F SC1 SO1 SI1 IC203 BUFFER CS0L SC0 SO0 SI0 XFRRST XIFINT 22 12 4A 4 2A 1 1A 4Y 11 2Y 1Y 6 3 XVIFCS IFSC0 IFSO0 IFSI0 XFRRST XIFINT SC1 SO1 SI1 S525D/S725D

IC207 4 POWER ON RESET 5

+3.3V IC201 4K EEPROM SC0 SO0 CE WE CS 4 WE, RY/BY, UB, LB, OE 112 113 124 125 SI0 4 SK 5 DI 6 DO CS 3 WC 8 R/B 1 23 XECS 24 XEWC 25 XEBSY


146-154 HA 0-5, 17-19

126-133 12 19 FD 0-7 18 21 24 I/O 0-7 27 2 5 40 43 HD 0-7

HA 0, 1

42 44-64 A 01-15

25-39 41 D 16-31

76 77 78 79 80 89 SI0 SO0 SI1 SO1 SC0 SC1

14 97 CS0L RST CS0 11

RF, SERVO(SEE PAGE 3-4) HD 8-15 X3VRST

NFD 0-7

IC601 HGA

5 11 56

TEST, CLE, ALE, XWE, XWP, XCE, XRE, R/B


IC202 SYSTEM CONTROL


GAIN2

3 PB7/DW1

CS1 CS4 RD WR0

10 7 22 23 24 19 94 88 83 5 XRD XWRH MUTE MD2 NORF DFCT FWON LOCK XARPRST XARPIT XARPWT XARPWR XARPRD XARPCS XAVDWT XAVDRST X57RST S725D XDACS0 XDACS1 S525D/S725D

141 CS1 142 CS4 145 HRD 144 HWRH 143 HWRL 157 WAIT 156 XINT1 155 XINT3 3 RST 135 CPUCK 98 MUTE 99 MD2 102 NORF 103 DFCT 104 FWON 105 LOCK 106 ARPRST 107 ARPINT 108 ARPWT 109 ARPWR 110 ARPRD 111 ARPCS 72 AVDWT 71 AVDRST 27 57RST 53 VS 52 RGB SEL 51 EURO V/Y 59 MCK MA MUTE 49 MA MUTE 01IT0 29 01IT1 30 01CS 28 XDACS2 96 97 01RST 31 DACRST 26 S525D/S725D X01INT0 X01INT1 X01CS XDACS2 XDACS3 X01RST XDACRST FCSON 54 SDPRST 114 SDPIT 115 SDPWR 116 SDPRD 117 SDPCS 118 SPDLSTOP 57 SPGAIN 94 XDRVMUTE 93 LDMP/DMP 92 LDMM/DMM 91 OCSW1 64 OCSW2 63 CKSW1 88 FCSON XSDPRST XSDPIT XSDPWR XSDPRD XSDPCS SPDLSTOP SPGAIN XDRVMUTE LDMP/DMP LDMM/DMM OCSW1 OCSW2 CKSW1


GAIN2

WR1 RDY INT1 INT3 PF7/OCPA0/ATG CLKIC2025

RF, SERVO(SEE PAGE 3-4)

X201 12.5MHz

91 X1 CS2 92 X0IC001!(DVD play) 4Vp-p(25.3MHz)

9 8

XCS2 XCS3 XAVDIT DACK1 DACK0 DREQ1 DREQ0

CS3

IC202(

INT0 95 DACK1 84 DACK0 85 DREQ1 86 DW0/PB3 CS0H/PB2 DREQ0 87 RAS0/PB0 85IC0035,7


4.2Vp-p(25.3MHz) 2.4Vp-p(12.5MHz) IC001!(CDplay)


RAS1/PB4

A22/P66

4.7Vp-p(22.5MHz) IC001!

66 100 DVD/CD CKSEL

99 98

VIDEO DISC/EXT (SEE PAGE 3-7) S325/ S525D: EXCEPT Australian S725D: EXCEPT Australian


DVD:5.8Vp-p(36.5MHz) CD:5.1Vp-p

DVD:6.2Vp-p(37.0MHz) CD:5Vp-p(33.6MHz)

IC001 PLL 1 19 MD X001 27MHz 1 6 ML IC003 XT1 SCKO2 14 SCKO1 12IC0016

VIDEO(SEE PAGE 3-7)

VS RGB EURO V/Y S325/ S525D: EXCEPT Australian S725D: EXCEPT Australian



7 5

384FSDA 384FS01 27M01 S525D/S725D 256FS30 33MARP 33M30


SCKO3 17

3


IC004 34.2Vp-p(27.0MHz) IC001!

5 2 7IC0042,5,7

S725D 27M57 27M30 N27MHGA

6 1

4.6Vp-p(33.8MHz)

N27MSDP4.2Vp-p(26.9MHz)

RF, SERVO(SEE PAGE 3-4)

05

3-9

3-10

DVP-S325/S525D/S725D3-6. AUDIO (1) BLOCK DIAGRAMMB-82/85 BOARD(5/7)(SEE PAGE 4-35,37)

S325 SPDIF1 BCK LRCK ACH12 S525D/S725D IC902 DO 16 AUDIO 2CH DAC 3 BCLKIN 1 LRCIN 2 D IN SO1 SC1 CS0 26 MD 27 MC 28 MLRSTB XTI

R502 R536 R538 R529

SPDIF

SIGNAL PROCESS(SEE PAGE 3-6) 47 BCKI 49 LRCKI 52 CH12I ACH34 ACH56 CDDOUT CDDATA CDBCK CDLRCK X01INT0 X01INT1 SO1 X01CS SI1 SC1 51 CH34I 50 CH56I 25 CDDOBYP 26 CDSOBYP 27 CDBKCKI 28 CDLRCKI 55 CPU INT0 56 CPU INT1 61 SI 62 CS 63 SOACKI

IC501 AUDIO DSP

BCKO 9 LRCKO 10 CH78O 11 CH12O 15 CH34O 14 CH56O 12

V OUT L 16 V OUT R 13 ZERO 21 ZEROR 17

AUDIOLT AUDIORT ZFLT ZFRT

22 5

S525D/S725D IC905 FRONT L/R DAC 3 BCLKIN 1 LRCIN CH12O SO1 SC1RST CLK

V OUT L 16 V OUT R 13 ZERO 21 ZEROR 17RSTB XTI

AUDIOL AUDIOR ZFL ZFR

2 D IN 26 MD 27 MC 28 ML

AUDIO 2 :S325/S525D (SEE PAGE 3-13) AUDIO 3 :S725D (SEE PAGE 3-15)

66 SCK

CS1

33 7 68

22 5

SO1 SC1 XDACS0 XDACS1 XDACS2 XDACS3

SO1 SC1 CS0 CS1 CS2 CS3 CH34O SO1 SC1 CS2 IC906 REAR L/R DAC 3 BCLKIN 1 LRCIN 2 D IN 26 MD 27 MC 28 MLRSTB XTI


V OUT L 16 V OUT R 13 ZERO 21 ZEROR 17

AUDIOLS AUDIORS ZFLS ZFRS

X01RST XDACRST

22 5

384FS01 27M01 384FSDA 3 BCLKIN 1 LRCIN CH56O SO1 SC1 CS3 2 D IN 26 MD 27 MC 28 ML

IC907 CENTER/WOOFER DAC V OUT L 16 V OUT R 13 ZERO 21 ZEROR 17RSTB XTI

AUDIOC AUDIOLFE ZFC ZFLFE

22 5

05

3-11

3-12

DVP-S325/S525D/S725D3-7. AUDIO (2) BLOCK DIAGRAM DVP-S325/S525D MB-82/85 BOARD(6/7)(SEE PAGE 4-37)

AU-209/212 BOARD(2/2)(SEE PAGE 4-45,47,67,69) Q341 BUFFER IC505 A MUTE

J502 COAXIAL DIGITAL OUT OPTICAL J506 : S325/S525D: EXCEPT Australian


1 D IN MA MUTE

SYSTEM CONTROL(SEE PAGE 3-9,10) GAIN2 CN005 SPDIF AUDIOLT AUDIORT ZFLT ZFRT 15 11 13 10 19 9 7 SPDIF AUDIOLT AUDIORT ZFLT ZFRT A MUTE MA MUTE 14 18 16 Q301 19 10 20 22 3 S525D Q314, 315 LEVEL SHIFT AUDIOL 21 23 20 27 AUDIOL AUDIOR ZFL ZFR 8 6 9 2 Q306 Q307 3 5 IC502 LPF +6dB 1 Q503, 504 MUTE 7 5 7 J508 Q305 IC401 HEAD PHONE AMP 1 Q401, 402 MUTE 3 3 5 CN301 IC431 LPF +6dB 1 7 S525D Q431,432 GAIN CONTROL Q435, 436 MUTE S325

L AUDIO OUT1 R J505 : S525D: Australian L AUDIO OUT2 R S525D

HP-108/111 BOARD(SEE PAGE 4-102) CN401 1 HPL HPR 1 3 RV701 LEVEL L FRONT R CN701 J701 PHONES

AUDIOR

AUDIO 1(SEE PAGE 3-12) ZFL ZFR

IC541 1 AUDIOLS AUDIORS ZFLS ZFRS 3 5 2 13 GAIN2 AUDIOLS AUDIORS ZFLS ZFRS 13 11 9 Q311 12 1 Q308 IC571 LPF +12dB, +16dB AUDIOC 7 9 6 12 CN007 AUDIOC AUDIOLFE ZFC ZFLFE 7 5 8 2 CN302 Q303, 304 MUTE CONTROL CN305 7 ERAUDIOR 05 S325/S525D: EXCEPT Australian 9 ERAUDIOL Q310 Q309 3 5 1 Q573, 574 MUTE 7 WOOFER CENTER 3 5 LPF +12dB 1 Q543, 544 MUTE 7 L REAR R 5.1CH OUTPUT

AUDIOLFE ZFC ZFLFE

7

9 RY904 4 2 7 9 1 3 8 3 6 1 2 A (L) OUT A (L) IN A (R) OUT A (R) IN CN904 EURO AV1 (RGB)-TV

ER-4 BOARD (2/2)(SEE PAGE 4-73,75)

CN902

VIDEO(SEE PAGE 3-7)

RELAY DRIVE CONT

Q915 RELAY DRIVE

RY905 4 2 7 9 1 Q916 RELAY DRIVE 3 8

3 6 1 2

A (L) OUT A (L) IN A (R) OUT A (R) IN

CN903 EURO AV2

3-13

3-14

DVP-S325/S525D/S725D3-8. AUDIO (3) BLOCK DIAGRAM DVP-S725D MB-82/85 BOARD(6/7)(SEE PAGE 4-37)

AU-210/211 BOARD(2/2)(SEE PAGE 4-53,55,61,63) Q303 BUFFER IC303 A MUTE

J301 COAXIAL DIGITAL OUT OPTICAL J307 :S725D: EXCEPT Australian


1 D IN MA MUTE

SYSTEM CONTROL(SEE PAGE 3-9,10) GAIN2 CN005 SPDIF AUDIOLT AUDIORT ZFLT ZFRT 15 11 13 10 19 9 7 SPDIF AUDIOLT AUDIORT ZFLT ZFRT A MUTE MA MUTE 14 18 16 Q431 19 10 20 22 3 Q437, 438 LEVEL SHIFT B401 (2/2) AUDIOL 21 23 20 27 AUDIOL AUDIOR ZFL ZFR 8 6 9 2 Q402 Q403 3 1 L R B404 3 1 2 6 5 Q401 IC411 HEADPHONE AMP 1 Q418, 419 MUTE IC404, 408 LPF +6dB 1 7 2 6 1 Q412, 413 MUTE 7 7 J303 3 CN402 B401 (1/2) 6 4 LT RT B403 3 1 IC401 GAIN CONTROL 2 6 IC403, 407 LPF +6dB 1 7 2 6 1 Q410, 411 MUTE 7

L AUDIO OUT1 R S725D: Australian L AUDIO OUT2 R J304

HP-109/110 BOARD(SEE PAGE 4-102) CN301 1 HPL HPR 1 3 CN701 J701 PHONES

RV701 LEVEL

L FRONT R

AUDIOR

AUDIO 1(SEE PAGE 3-12) ZFL ZFR

IC405, 409 1 AUDIOLS AUDIORS ZFLS ZFRS 3 5 2 13 GAIN2 AUDIOLS AUDIORS ZFLS ZFRS 13 11 9 Q404 12 1 Q432 IC406, 410 B402 (2/2) AUDIOC 7 9 6 12 CN007 AUDIOC AUDIOLFE ZFC ZFLFE 7 5 8 2 CN403 Q405, 435 MUTE CONTROL CN302 7 05 S725D: EXCEPT Australian ERAUDIOR 9 ERAUDIOL Q433 Q434 3 1 C W B406 3 1 2 6 LPF +12dB, +16dB 1 7 2 6 1 Q416, 417 MUTE 7 WOOFER CENTER B402 (1/2) 6 4 LS RS B405 3 1 2 6 LPF +12dB 1 7 2 6 1 Q414, 415 MUTE 7 L REAR R 5.1CH OUTPUT

AUDIOLFE ZFC ZFLFE

7

9 RY904 4 2 7 9 1 3 8 3 6 1 2 A (L) OUT A (L) IN A (R) OUT A (R) IN CN904 EURO AV1 (RGB)-TV

ER-5 BOARD (2/2)(SEE PAGE 4-81,83)

CN902

VIDEO(SEE PAGE 3-7)

RELAY DRIVE CONT

Q915 RELAY DRIVE

RY905 4 2 7 9 1 Q916 RELAY DRIVE 3 8

3 6 1 2

A (L) OUT A (L) IN A (R) OUT A (R) IN

CN903 EURO AV2

3-15

3-16

DVP-S325/S525D/S725D3-9. INTERFACE CONTROL BLOCK DIAGRAMFL-98/99/100/101 BOARD FR-147/148/ 149/150 BOARD(SEE PAGE 4-99) CN202 S525D/S725D IC051 REMOTE COMMANDER RECEIVER OUT 1 IC201 IF CON CN002 4 6 7 VIRTUAL 3D SURROUND :S725D IC202 POWER-ON RESET D071 CN099 Q098 LED DRIVE 3 2 LVES BT25 3 2 CN003 ON/STANDBY 1 2 LVES BT25 1 2 27 L VES 4 AN2 X INIC201!

MB-82/85 BOARD(7/7)(SEE PAGE 4-31)

(SEE PAGE 4-93,95)

CN006 6 4 SC0 SI0 6 4 IFSC0 IFSI0

SCLK1 SOUT1

70 71

SW-314/315/ 316/317 BOARD(SEE PAGE 4-99) D098 VES :S525D

CN201 IR POWER STBY 4 6 7 9 IR

SIN1 SBUSY1

72 76

5 3

SO0 XIFCS

5 3 +5V

IFSO0 XVIFCS

SYSTEM CONTROL(SEE PAGE 3-10)

31 L POWER 32 L STBY

SRDY1 P CHECK FRRST

78 77 8 11 12 14 15 S525D/S725D

2 15 1 8 9 X201 4MHz

XIFBUSY +3.3V XFRRST V MUTE A MUTE

2 15 1 8 9 +3.3V

XIFINT

XFRRST V MUTE A MUTE

V OUT 4

10 RESET

V MUTE A MUTE

VIDEO(SEE PAGE 3-7)



X OUT

S098 VES :S525D :S725D

S071

S224 SHUFFLE BT11

S223 PROGRAM

S222 CLEAR

S221 REPEAT3.9Vp-p(4MHz)

L JOG L MULTI

29 30

VIRTUAL 3D SURROUND

S525D/S725D 3 S725D S217, 218 SEARCH 5 AN1

3

D203 MULTI CHANNEL S218 NEXT S217 PREV S216 RETURN S215 DVD MENU S214 TITLE S213 S212 OPEN/CLOSE S525D/S725D 17 JOG CCW, 18 JOG CW 33 37 41 48 39 40 49 56 58 64 DIG1-13 31 38 49 53 8 14 19 26 44 45

D204 JOG

JOG UNIT 1 2 ENTER 4 6 I 9

CN203 JOG CCW, JOG CW S525D/S725D LEFT, RIGHT, UP, DOWN, ENTER DCS CCW, DCS CW S325/S525D

ENTER

DOWN

RIGHT

UP

S230 PREV NEXT ACS ENTER

LEFT

25 DCS CCW, 26 DCS CW S725D 6 AN0

ND201 VACUUM FLUORECENT DISPLAY

SEG1-17

PUSH S725D S208 JOG S525D/S725D 05 S202 S201

3-17

3-18

DVP-S325/S525D/S725D3-10. POWER BLOCK DIAGRAMS725D CN201 1 ACOUT L, N 3 CN202 4 2 1 6 7 PC101 PHOTO COUPLER PC103, Q131 POWER CONTROL Q181-183 SWITCH T102 EVER5V CN202 2 1 5 6 7 CN203 1 PC102 PHOTO COUPLER 3 5 2 PCONT +5V 12V EVER5V S325/S525D M+12V A+12V +5V +3.3V EVER5V 7 EVER5V +12V +5V +3.3V 12V EVER5V 1 +12V 1 CN404 +12V +5V 4 2 Q422-424 SWITCH IC301 IC302 T901 RCORE TRANS AC10V 1 4 CN407

HS-030SH BOARD(SEE PAGE 4-107)

CN102 1 2 CN201 ACOUT L, N 1 3

CN101

RY101

CN401 D401-404 IC412, Q420, 421 +9V, 9V REG IC415 +5V REG IC303

1 2

CN101 F101

D101 L101, 102 LINE FILTER Q101-103 SWITCH

T101

+12V +5V +3.3V 12V

P211 P311 P611 P511

IC401 IC402 IC403 IC404 IC405 IC406 IC407 IC408 IC409 IC410 IC411 IC413 IC414

RY-12 BOARD(SEE PAGE 4-104)

AU-210/211 BOARD(SEE PAGE 4-53,55,61,63) 11 18 10EVER5V +12V +5V

CN302

AU-209/212 BOARD(SEE PAGE 4-45,47,67,69) 12V B301 6 IC302 9V REG

S725D: EXCEPT Australian

IC431

S325/S525D: EXCEPT Australian/S725D: EXCEPT Australian

+12V

4

IC301 +9V REG

+5V

2

IC303

IC401 IC502 IC541 IC571

CN902 +5V 10

IC901 IC902 IC903 EVER5V +12V

EVER5V S525D IC321 IC505 CN305 18 10 11 EVER5V CN201 ND201 8 9 F1 F2 8 9 CN002 Q001, 002 T001 DC-DC CONVERTER CN001 5 12V +3.3V 7 1 EVER5V +3.3V +12V +5V EVER5V +12V

11 18

FL-98/99/100/101 BOARD(SEE PAGE 4-93,95)

FR-147/148/149/150 BOARD(SEE PAGE 4-99)

ER-4/5 BOARD(SEE PAGE 4-73,81)

S325/S525D: EXCEPT Australian

IC201

Q201 30V REG

10 5

VEE EVER5V

10 5 IC051 2 EVER5V +5V +3.3V 1 CN003 1 PCONT 5 6 7

MB-82/85 BOARD(SEE PAGE 4-21~39) CN001 +5V +3.3V S725D IC404 +3.3 REG IC401 IC302 +3.3 REG IC303 IC203 IC702 IC803 IC201 IC202 IC204 IC207 IC304 IC402 IC403 IC601 IC701 IC502 IC602 CN002 18 9 +5V +3.3V 1 10

TK-51/54 BOARD(SEE PAGE 4-13) CN003 CN001 14 VCC (5V) OPTICAL DEVICE

PCONT

IC202 PCONT

12 CN202 +3.3V 15

12

IC001

V3.3VEVER5V

IC501 S525D/S725D

05

SW-314/315/ 316/317 BOARD(SEE PAGE 4-99) CN099 EVER5V S525D/S725D 1

A+12V

1

A+12V

IC904 A+5V A+5V REG IC001 IC902 IC005 +3.3 REG

IC205 S325/S525D

M+12V +3.3V

2 15

S12V CN006

IC801 IC802

IC905 IC906 IC907 S525D/S725D

IC003 IC004

IC206 S725D

3-19

3-20 E

DVP-S325/S525D/S725D SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMSTHIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary mote is printed in each block.)For printed wiring boards: X : indicates a lead wire mounted on the component side. x : indicates a lead wire mounted on the printed side. : Through hole. b : Pattern from the side which enables seeing. (The other layers patterns are not indicated.) Caution: Pattern face side: (Side B) Parts face side: (Side A) For schematic Diagram: Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, because it is damaged by the heat. All resistors are in ohms, 1/4 W (Chip resistors : 1/10 W) unless otherwise specified. k : 1000, M : 1000k. All capacitors are in F unless otherwise noted. pF : F 50V or less are not indicated except for electrolytics and tantalums. All variable and adjustable resistors have characteristic curve B, unless otherwise noted. 2 : nonflammable resistor. 5 : fusible resistor. C : panel designation. : internal component. C : adjustment for repair. U : B+ Line. V : B Line. Circled numbers refer to waveforms. Voltages are dc between measurement point. Readings are taken with a color-bar signals on DVD reference disc and when playing CD reference disc. Readings are taken with a digital multimeter (DC 10M). Voltage variations may be noted due to normal production tolerances. Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board name. Abbreviation AUS : Australian RUS : Russian E12B : Black type in E model E12S : Silver type in E model

Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.

Abbreviation AUS : Australian

4-1

DVP-S325/S525D/S725D

4-1. FRAME SCHEMATIC DIAGRAMSFRAME (1) SCHEMATIC DIAGRAM

FRAME (1/3)4-3 4-4


FRAME (2) SCHEMATIC DIAGRAM DVP-S325/S525D

FRAME (2/3)4-5 4-6


FRAME (3) SCHEMATIC DIAGRAM DVP-S725D

FRAME (3/3)4-7 4-8


4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMSTK-51/54 (RF/SERVO) PRINTED WIRING BOARD Ref. No.: TK-51/54 board; 2,000 series

There are few cases that the part isn't mounted in this model is printed on this diagram.

TK-51/54 BOARD(SIDE A)

TK-51/54 BOARD (SIDE A) CN001 CN002 CN003 CN004 D003 IC001 Q001 Q002 B-2 C-2 D-2 D-3 B-2 C-1 A-2 D-1

AE C B


B


CMS-29 (LOADING) MB-82 (Australian) MB-85 (EXCEPT Australian) (SIGNAL PROCESS/SERVO) FL-98 (S325/S525D: EXCEPT Australian) FL-99 (S725D: Australian) FL-100 (S725D: EXCEPT Australian) FL-101 (S525D: Australian) (FUNCTION SWITCH)C E B


DCN003

12 (12)

05

14-10

2

3TK-51:1-672-677TK-54:1-673-437-

RF/SERVOTK-51/544-9

DVP-S325/S525D/S725D Waveforms1 IC001 1 (DVD play) 200 mV/DIV 100 ns/DIV 6 IC001 # (CD play) 500 mV/DIV 200 ms/DIV

TK-51/54 BOARD(SIDE B)

536 mVp-p 2 IC001 1 (CD play) 500 mV/DIV 500 ns/DIV

1.7 Vp-p 7 IC001 $ (DVD play) 100 mV/DIV 50 ms/DIV

880 mVp-p 3 IC001 @ (DVD play) 200 mV/DIV 500 ms/DIV

180 mVp-p 8 IC001 $ (CD play) 500 mV/DIV 50 ms/DIV

592 mVp-p 4 IC001 @ (CD play) 200 mV/DIV 20 ms/DIV

860 mVp-p 9 IC001 % (DVD play) 500 mV/DIV 100 ns/DIV

448 mVp-p 5 IC001 # (DVD play) 500 mV/DIV 50 ms/DIV

1.5 Vp-p ! IC001 % (CD play) 500 mV/DIV 500 ns/DIV

1205 TK-51:1-672-677TK-54:1-673-4374-11 4-12

(12)

1.3 Vp-p

1.5 Vp-p

RF/SERVOTK-51/54


TK-51/54 (RF/SERVO) SCHEMATIC DIAGRAM Ref. No.: TK-51/54 board; 2,000 series

See page 4-9 for printed wiring board and page 4-12 for waveforms.

Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

RF/SERVOTK-51/544-13 4-14


MS-29 (LOADING) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM Ref. No.: MS-29 board; 3,000 series


MS-29 BOARDS001 (TRAY SENSOR) S001 CN001

LOADING MOTOR

(CHUCK SENSOR)

1105FR-147 (S325/S525D: EXCEPT Australian) AU-209 (S325/S525D: EXCEPT Australian) FR-148 (S725D: Australian) AU-210 (S725D: Australian) FR-149 (S725D: EXCEPT Australian) AU-211 (S725D: EXCEPT Australian) FR-150 (S525D: Australian) AU-212 (S525D: Australian) TK-51 (IR/POWER SWITCH) (AUDIO) (Australian) TK-54 (EXCEPT Australian) (RF/SERVO) Power Block (HS-030SH) (SWITCHING REGULATOR) ER-4 RY-12 (S725D) (S325/S525D: EXCEPT Australian) (RELAY) ER-5 (S725D: EXCEPT Australian) (EURO AV)

1-672-678-

(11)


MS-29 (LOADING)



LOADING4-15 4-16

MS-29


MB-82/85 (SIGNAL PROCESS/SERVO) PRINTED WIRING BOARD Ref. No.: MB-82/85 board; 1,000 series


MB-82/85 BOARD (SIDE A) CN001 CN002 CN003 CN004 CN005 CN006 CN007 CN010 CN011 CN012 D801 D802 D803 D804 D805 D807 IC001 IC003 IC004 IC202 IC205 IC206 IC302 IC303 IC401 IC501 IC601 IC701 IC904 Q801 Q802 Q803 D-2 D-4 D-5 C-1 B-1 C-7 C-1 B-6 D-6 D-6 C-6 C-6 C-6 C-6 C-5 C-5 A-2 A-3 B-3 A-5 A-6 A-6 D-3 C-4 C-2 A-2 A-4 C-5 A-1 C-5 C-6 C-6

MB-82/85 BOARD(SIDE A)


MB-82:1-672-676MB-85:1-672-751-


MS-29 (LOADING)



SIGNAL PROCESS/SERVOMB-82/854-17 4-18


MB82/85 BOARD(SIDE B)MB-82/85 BOARD (SIDE B) D701 D806 IC005 IC201 IC203 IC204 IC207 IC304 IC402 IC403 IC404 IC502 IC602 IC702 IC801 IC802 IC803 IC902 IC905 IC906 IC907 C-2 C-2 A-6 A-3 A-3 B-2 A-2 C-3 C-5 C-5 D-5 C-6 A-4 B-1 C-2 C-1 C-1 A-6 B-6 B-6 C-6

MB-82:1-672-676MB-85:1-672-751-

SIGNAL PROCESS/SERVO4-19 4-20

MB-82/85

DVP-S325/S525D/S725DMB-82/85 (AV DECODER) SCHEMATIC DIAGRAM See page 4-17 for printed wiring board. Ref. No.: MB-82/85 board; 1,000 series

AV DECODERMB-82/85 (1/10)4-21 4-22

DVP-S325/S525D/S725DMB-82/85 (SDRAM) SCHEMATIC DIAGRAM Ref. No.: MB-82/85 board; 1,000 series See page 4-17 for printed wiring board. Waveforms1 IC401 % 3 IC401 % (RGB output model)

720 mVp-p (H) 1 IC401 % (RGB output model)

1.0 Vp-p (H) 4 IC401 ^

720 mVp-p (H) 2 IC401 %

1.1 Vp-p (H) 5 IC401 ^

728 mVp-p (H) 2 IC401 % (RGB output model)

816 mVp-p (H) 6 IC401 ^

728 mVp-p (H) 3 IC401 %

1.2 Vp-p (H)

1.0 Vp-p (H)

4-23

4-24

MB-82/85 (2/10)

SDRAM


MB-82/85 (SERVO DSP) SCHEMATIC DIAGRAM Ref. No.: MB-82/85 board; 1,000 series Waveforms1 IC701 ^ (DVD play) 500 mV/DIV 50 ms/DIV

See page 4-17 for printed wiring board.

1.4 Vp-p 2 IC701 ^ (CD play) 500 mV/DIV 200 mV/DIV

1.7 Vp-p 3 IC701 ^ (DVD play) 100 mV/DIV 5 ms/DIV

180 mVp-p 4 IC701 ^ (CD play) 500 mV/DIV 50 ms/DIV

860 mVp-p

SERVO DSPMB-82/85 (3/10)4-25 4-26

DVP-S325/S525D/S725DMB-82/85 (DRIVE) SCHEMATIC DIAGRAM See page 4-17 for printed wiring board. Ref. No.: MB-82/85 board; 1,000 series

4-27

4-28

MB-82/85 (4/10)

DRIVE

DVP-S325/S525D/S725DMB-82/85 (ARP) SCHEMATIC DIAGRAM Ref. No.: MB-82/85 board; 1,000 series See page 4-17 for printed wiring board.

Waveforms1 IC303 ! (DVD play) 500 mV/DIV 100 ns/DIV

1.6 Vp-p 2 IC303 ! (CD play) 500 mV/DIV 200 ns/DIV

1.6 Vp-p

MB-82/85 (5/10)

ARP

4-29

4-30

DVP-S325/S525D/S725DMB-82/85 (SYSTEM CONTROL) SCHEMATIC DIAGRAM Ref. No.: MB-82/85 board; 1,000 series See page 4-17 for printed wiring board.

D

V

Waveforms1 IC202 ( 2 IC202 5

SYSTEM CONTROL4-312.4 Vp-p (12.5 MHz) 4 Vp-p (25.3 MHz)

4-32

MB-82/85 (6/10)

DVP-S325/S525D/S725DMB-82/85 (HGA) SCHEMATIC DIAGRAM Ref. No.: MB-82/85 board; 1,000 series See page 4-17 for printed wiring board.

MB-82/85 (7/10)

HGA

4-33

4-34

DVP-S325/S525D/S725DMB-82/85 (CLOCK GENERATOR, AUDIO DSP, V EQ/NR) SCHEMATIC DIAGRAM Ref. No.: MB-82/85 board; 1,000 series See page 4-17 for printed wiring board and page 4-40 for waveforms.

4-36

CLOCK GENERATOR, AUDIO DSP, V EQ/NR4-35

MB-82/85 (8/10)


MB-82/85 (DAC) SCHEMATIC DIAGRAM Ref. No.: MB-82/85 board; 1,000 series


MB-82/85 (9/10)

DAC

4-37

4-38


MB-82/85 (BIAS) SCHEMATIC DIAGRAM Ref. No.: MB-82/85 board; 1,000 series


Waveforms1 IC004 2, 5, 7 6 IC001 ! (DVD play)

4.2 Vp-p (26.9 MHz) 2 IC003 5, 7

4.2 Vp-p (25.3 MHz) 7 IC001 ! (CD play)

DVD: 6.2 Vp-p (37.0 MHz) CD : 5 Vp-p (33.6 MHz) 3 IC001 6

4.7 Vp-p (22.5 MHz)

4.2 Vp-p (27.0 MHz) 4 IC001 !

4.6 Vp-p (33.8 MHz) 5 IC001 !

DVD : 5.8 Vp-p (36.5 MHz) CD : 5.1 Vp-p (33.8 MHz)

4-39

4-40

MB-82/85 (10/10)

BIAS


AU-209 (AUDIO, VIDEO BUFFER) PRINTED WIRING BOARD Ref. No.: AU-209 board; 2,000 series DVP-S325/S525D:EXCEPT AUS AU-209 BOARD CN301 CN302 CN305 CN401 D301 D304 D306 D308 D431 D432 D525 D526 D551 D552 D591 D592 IC301 IC302 IC321 IC401 IC431 IC502 IC505 IC541 IC571 Q301 Q303 Q304 Q305 Q306 Q307 Q308 Q309 Q310 Q311 Q314 Q315 Q321 Q322 Q341 Q401 Q402 Q431 Q432 Q435 Q436 Q503 Q504 Q543 Q544 Q573 Q574 B-2 B-3 B-6 C-7 A-11 A-5 A-5 B-6 A-8 A-8 A-9 A-8 A-10 A-9 A-11 A-11 C-11 A-11 B-3 A-6 B-7 B-8 A-1 B-9 B-10 B-5 A-11 B-6 C-3 C-9 C-7 C-10 C-10 C-10 C-10 B-2 B-3 B-4 B-4 A-1 A-6 A-6 B-7 B-7 C-6 A-8 B-9 A-8 B-10 A-9 B-11 A-10


AU-209 BOARDDIGITAL OUT OPTICAL COAXIAL R AUDIO L LINE OUT VIDEO S VIDEO OUT FRONT 5.1 CH OUTPUT REAR CENTER / WOOFER

AK A K K A K

1 2 3

B

1 2 3

C

111-672-26405

(11)

1

2

3

4

5

6

7

8

9

10

11

12



MS-29 (LOADING)



AUDIO, VIDEO BUFFER4-43 4-44

AU-209


AU-209 (AUDIO) SCHEMATIC DIAGRAM Ref. No.: AU-209 board; 2,000 series DVP-S325/S525D: EXCEPT AUS


AUDIOAU-2094-45 4-46


AU-209 (VIDEO BUFFER) SCHEMATIC DIAGRAM See page 4-43 for printed wiring board. Ref. No.: AU-209 board; 2,000 series DVP-S325/S525D: EXCEPT AUS

Waveforms1 IC321 2 6 IC321 !

1.1 Vp-p (H) 2 IC321 4

2.0 Vp-p (H)

1.2 Vp-p (H) 3 IC321 7

860 mVp-p (H) 4 IC321 !

1.8 Vp-p (H) 5 IC321 !

2.4 Vp-p (H)

VIDEO BUFFER4-47 4-48

AU-209


AU-210 (AUDIO, VIDEO BUFFER) PRINTED WIRING BOARD Ref. No.: AU-210 board; 3,000 series DVP-S725D: AUS


AU-210 BOARD(SIDE

A)

111-672-248-

(11)

05



MS-29 (LOADING)



AUDIO, VIDEO BUFFERAU-2104-49 4-50


AU-210 BOARD(SIDEOPTICAL

B)COAXIAL VIDEO OUT S VIDEO OUT Y

COMPONENT VIDEO OUT AUDIO OUT CB/B-Y CR/R-Y 1 2 FRONT 5.1CH OUTPUT REAR CENTER/WOOFER

DIGITAL OUT

AU-210 BOARD (SIDE B) CN301 CN401 CN402 CN403 CN404 CN405 CN407 D301 D302 D303 D304 D401 D402 D403 D404 D405 D406 D407 D408 D409 D410 D411 D421 D422 D423 D424 D425 IC301 IC302 IC303 IC401 IC403 IC404 IC405 IC406 IC407 IC408 IC409 IC410 IC411 IC412 IC415 Q301 Q302 Q303 Q401 Q402 Q403 Q404 Q405 Q410 Q411 Q412 Q413 Q414 Q415 Q416 Q417 Q418 Q419 Q420 Q421 Q422 Q423 Q424 Q431 Q432 Q433 Q434 Q435 Q437 Q438 C-5 C-11 C-2 C-3 C-4 C-4 C-5 A-4 A-4 A-4 A-4 C-11 C-11 C-11 C-11 C-4 B-4 B-4 B-4 B-4 A-11 A-11 B-5 B-5 B-5 B-5 C-4 B-1 B-3 A-1 C-7 B-7 B-8 C-9 C-10 B-7 B-8 B-9 B-10 B-5 B-11 C-5 B-2 B-2 A-1 B-4 B-4 B-4 B-4 B-4 A-7 A-6 A-8 A-8 A-9 A-9 A-10 A-10 B-5 B-5 B-12 B-11 A-11 A-11 A-11 B-4 B-5 B-5 B-5 C-5 C-7 C-8

K

K A

A

K A

K

A K KK

A K

B

1

27 1 2 28 1 13 4 1 7

2

C

12

111-672-24805

(11)

1

2

3

4

5

6

7

8

9

10

11

12

AUDIO, VIDEO BUFFER4-51 4-52

AU-210

DVP-S325/S525D/S725DAU-210 (AUDIO) SCHEMATIC DIAGRAM Ref. No.: AU-210 board; 3,000 series DVP-S725D: AUS


AU-210 (1/2)

AUDIO

4-53

4-54

DVP-S325/S525D/S725DAU-210 (VIDEO BUFFER) SCHEMATIC DIAGRAM Ref. No.: AU-210 board; 3,000 series DVP-S725D: AUS

See page 4-49 for printed wiring board. Waveforms1 IC301 2 6 IC301 !

1.1 Vp-p (H) 2 IC301 4

2.0 Vp-p (H)

1.2 Vp-p (H) 3 IC301 7

860 mVp-p (H) 4 IC301 !

1.8 Vp-p (H) 5 IC301 !

2.4 Vp-p (H)


AU-210 (2/2)


AU-211 (AUDIO, VIDEO BUFFER) PRINTED WIRING BOARD Ref. No.: AU-211 board; 3,000 series DVP-S725D: EXCEPT AUS There are few cases that the part isn't mounted in this model is printed on this diagram.



MS-29 (LOADING)





AU-211 BOARD (SIDE B) CN301 CN302 CN401 CN402 CN403 CN404 CN405 CN406 CN407 D301 D303 D401 D402 D403 D404 D405 D406 D407 D408 D409 D410 D411 D421 D422 D423 D424 D425 D426 D427 IC301 IC302 IC303 IC401 IC403 IC404 IC405 IC406 IC407 IC408 IC409 IC410 IC411 IC412 IC415 Q301 Q302 Q303 Q401 Q402 Q403 Q404 Q405 Q410 Q411 Q412 Q413 Q414 Q415 Q416 Q417 Q418 Q419 Q420 Q421 Q422 Q423 Q424 Q425 Q426 Q427 Q431 Q432 Q433 Q434 Q435 Q437 Q438 Q439 Q440 C-5 B-4 C-11 C-2 C-3 C-4 C-3 B-3 C-5 A-4 A-4 C-11 C-11 C-11 C-11 C-4 B-4 B-4 B-4 B-4 A-11 A-11 B-5 B-5 B-5 B-5 C-4 B-2 B-2 B-1 B-3 A-1 C-7 B-7 C-8 C-9 C-10 B-7 B-8 B-9 B-10 B-5 B-11 C-5 B-2 B-2 A-1 B-4 B-4 B-4 B-4 B-4 A-7 A-6 A-8 A-8 A-9 A-9 A-10 A-10 B-5 B-5 B-12 B-11 A-11 A-11 A-11 B-3 B-3 B-3 B-4 B-5 B-5 B-5 C-5 C-7 C-8 B-3 B-3

K K A K A

K

1 2

1

27

7 1

1 17 7 18

2

28

1

13 4 1

2

12

4-59

4-60

AUDIO, VIDEO BUFFERAU-211

DVP-S325/S525D/S725DAU-211 (AUDIO) SCHEMATIC DIAGRAM Ref. No.: AU-211 board; 3,000 series DVP-S725D: EXCEPT AUS


AU-211 (1/2)

AUDIO

4-61

4-62


AU-211 (VIDEO BUFFER) SCHEMATIC DIAGRAM Ref. No.: AU-211 board; 3,000 series DVP-S725D: EXCEPT AUS



1.1 Vp-p (H) 2 IC301 4

2.0 Vp-p (H)

1.2 Vp-p (H) 3 IC301 7

860 mVp-p (H) 4 IC301 !

1.8 Vp-p (H) 5 IC301 !

2.4 Vp-p (H)


AU-211 (2/2)

DVP-S325/S525D/S725DAU-212 (AUDIO, VIDEO BUFFER) PRINTED WIRING BOARD Ref. No.: AU-212 board; 2,000 series DVP-S525D: AUS There are few cases that the part isn't mounted in this model is printed on this diagram.

AU-212 BOARDDIGITAL OUT OPTICAL COAXIAL R AUDIO L LINE OUT VIDEO S VIDEO OUT Y COMPONENT VIDEO OUT CB / B-Y CR / R-Y FRONT 5.1 CH OUTPUT REAR CENTER/WOOFER

AU-212 BOARD CN301 CN302 CN303 CN401 D301 D304 D305 D306 D307 D308 D431 D432 D525 D526 D551 D552 D591 D592 IC301 IC302 IC303 IC321 IC401 IC431 IC502 IC505 IC541 IC571 Q301 Q303 Q304 Q305 Q306 Q307 Q308 Q309 Q310 Q311 Q314 Q315 Q321 Q322 Q341 Q401 Q402 Q431 Q432 Q435 Q436 Q503 Q504 Q543 Q544 Q573 Q574 B-2 B-3 B-3 C-7 A-11 A-5 A-5 A-5 A-5 B-2 A-8 A-8 A-9 A-8 A-10 A-9 A-11 A-11 C-11 A-11 B-6 B-3 B-5 B-7 B-8 A-1 B-9 B-10 B-4 A-11 C-2 C-6 C-9 C-7 C-9 C-10 C-10 C-10 B-3 B-3 B-3 B-7 A-1 B-6 B-6 B-7 C-7 C-6 A-8 B-9 A-8 A-10 A-9 B-10 A-10

A

A

K K A K K A K K A K K A K K

1 2 3

B

1 2 3

C

111-672-23705

(11)

1

2

3

4

5

6

7

8

9

10

11

12



MS-29 (LOADING)




DVP-S325/S525D/S725DAU-212 (AUDIO) SCHEMATIC DIAGRAM Ref. No.: AU-212 board; 2,000 series DVP-S525D: AUS

4-67

4-68

AU-212 (1/2)

AUDIO


AU-212 (VIDEO BUFFER) SCHEMATIC DIAGRAM Ref. No.: AU-212 board; 2,000 series DVP-S525D: AUS



1.1 Vp-p (H) 2 IC321 4

2.0 Vp-p (H)

1.2 Vp-p (H) 3 IC321 7

860 mVp-p (H) 4 IC321 !

1.8 Vp-p (H) 5 IC321 !

2.4 Vp-p (H)

VIDEO BUFFERAU-212 (2/2)4-69 4-70


ER-4 (EURO AV) PRINTED WIRING BOARD Ref. No.: ER-4 board; 2,000 series DVP-S325/S525D: EXCEPT AUS


ER-4 BOARD

ER-4 BOARD

EURO AV1 (RGB) - TV

EURO AV2

CN901 CN902 CN903 CN904 D901 D902 D903 D904 D905 D906 D908 D915 D917 D918 D919 D920 D921 D922 D923 D924 D926 D927 D929 D930 IC901 IC902 IC903 Q901 Q902 Q903 Q904 Q905 Q906 Q907 Q908 Q909 Q910 Q912 Q913 Q914 Q915 Q916

C-3 B-6 A-5 A-2 B-5 A-1 B-2 B-3 B-4 B-5 A-4 A-5 A-1 A-2 A-2 A-2 A-2 A-2 A-3 A-3 A-4 A-3 A-1 A-1 C-2 B-2 B-4 C-4 C-4 B-5 C-5 B-5 C-5 C-5 B-5 B-5 B-4 A-1 B-2 B-3 A-4 B-5

K A K A K K K A K K A KK A KK A KK A K A K

K A K K A K K

A

1 2

B17 18

C05

111-672-269-

(11)

1

2

3

4

5

6



MS-29 (LOADING)



EURO AVER-4

4-71

4-72

DVP-S325/S525D/S725DER-4 (EURO AV1) SCHEMATIC DIAGRAM Ref. No.: ER-4 board; 2,000 series DVP-S325/S525D: EXCEPT AUS


EURO AV1ER-4 (1/2)4-73 4-74

DVP-S325/S525D/S725DER-4 (EURO AV2) SCHEMATIC DIAGRAM Ref. No.: ER-4 board; 2,000 series DVP-S325/S525D: EXCEPT AUS


EURO AV14-75 4-76

ER-4 (2/2)


ER-5 (EURO AV) PRINTED WIRING BOARD Ref. No.: ER-5 board; 2,000 series DVP-S725D: EXCEPT AUS There are few cases that the part isn't mounted in this model is printed on this diagram.

ER-5 BOARD(SIDE A)

1205 1-672-258-

(12)



MS-29 (LOADING)



EURO AVER-54-77 4-78


ER-5 BOARD(SIDE B)

EURO AV1 (RGB) - TV

EURO AV2ER-5 BOARD (SIDE B) CN901 CN902 CN903 CN904 D901 D902 D903 D904 D905 D906 D907 D908 D910 D915 D917 D918 D919 D920 D921 D922 D923 D924 D926 D927 D929 D930 IC901 IC902 IC903 Q901 Q902 Q903 Q904 Q905 Q906 Q907 Q908 Q909 Q910 Q912 Q913 Q914 Q915 Q916 Q917 Q918 C-3 B-6 A-5 A-2 B-4 A-1 B-2 B-3 B-4 B-5 B-4 A-4 B-3 A-5 A-1 A-2 A-2 A-2 A-2 A-2 A-3 A-3 A-4 A-3 A-1 A-1 C-2 B-2 B-4 C-4 C-4 C-4 C-5 B-5 C-5 C-5 B-5 B-5 B-4 A-1 B-2 B-3 A-4 B-5 B-3 B-3

A

K A K KK A K K A KK A KK A KK A K A

K

K A

K A

K K

K A

K

1 2

B17 18

C05

7

1

121-672-258-

(12)

1

2

3

4

5

6

EURO AV4-79 4-80

ER-5

DVP-S325/S525D/S725DER-5 (EURO AV1) SCHEMATIC DIAGRAM Ref. No.: ER-5 board; 2,000 series DVP-S725D: EXCEPT AUS


EURO AV1ER-5 (1/2)4-81 4-82

ER-5 (EURO AV2) SCHEMATIC DIAGRAM Ref. No.: ER-5 board; 2,000 series DVP-S725D: EXCEPT AUS



EURO AV24-83 4-84

ER-5 (2/2)


FL-98/101 (FUNCTION SWITCH, IF CON) PRINTED WIRING BOARD Ref. No.: FL-98/101 board; 2,000 series DVP-S325/S525D


FL-98/101 BOARDFL-98/101 BOARD CN201 CN202 CN203 D202 D203 D204 D206 D207 IC201 IC202 Q201 C-1 C-10 C-12 A-10 C-1 C-13 B-1 B-1 B-9 A-10PREV

PROGRAM

CLEAR

TITLE

DVD MENU

RETURN

ASHUFFLE

FLUORESCENT INDICATOR TUBE

3 4

1 5

REPEATNEXT

B-1

BD204,S208 JOG

9

1

OPEN/CLOSE

C 1

D203

MULTI CANNEL

17

1

11FL-98 : 1-672-265FL-101 : 1-672-23805

(11)

2

3

4

5

6

7

8

9

10

11

12

13



MS-29 (LOADING)



FUNCTION SWITCH, IF CON4-87 4-88

FL-98/101


FL-99/100 (FUNCTION SWITCH, IF CON) PRINTED WIRING BOARD Ref. No.: FL-99/100 board; 2,000 series DVP-S725D


FL-99/100 BOARD(SIDE

A)

05

12 (12)FL-99 : 1-672-249FL-100 : 1-672-254-



MS-29 (LOADING)



FUNCTION SWITCH, IF CONFL-99/1004-89 4-90


FL-99 /100 BOARD CN201 CN202 CN203 C-1 C-10 C-12 A-10 C-1 C-13 B-1 B-1 B-9 A-10 B-1

FL-99/100 BOARD(SIDEPROGRAM

B)

CLEAR

D202 D203 D204 D206 D207TITLE DVD MENU RETURN

ASHUFFLE

FLUORESCENT INDICATOR TUBE

IC201 IC2023 4 1 5

Q201

REPEAT

SEARCH SEARCH

BD204,S208 JOG

9

1

OPEN/CLOSE

C 1

D203

MULTI CANNEL

17

1

12 (12)FL-99 : 1-672-249FL-100 : 1-672-254-

S230 PREV PUSH NEXT

05

2

3

4

5

6

7

8

9

10

11

12

13

FUNCTION SWITCH, IF CON4-91 4-92

FL-99/100


FL-98/99/100/101 (FUNCTION SWITCH) SCHEMATIC DIAGRAM See pages 4-87 and 4-89 for printed wiring board. Ref. No.: FL-98/99/100/101 board; 2,000 series

FUNCTION SWITCHFL-98/99/100/101 (1/2)4-93 4-94


FL-98/99/100/101 (IF CON) SCHEMATIC DIAGRAM See pages 4-87 and 4-89 for printed wiring board. Ref. No.: FL-98/99/100/101 board; 2,000 series

Waveform1 IC201 !

3.9 Vp-p (4 MHz)

4-95

4-96

FL-98/99/100/101 (2/2)

IF CON


SW-314/315/316/317 (SURROUND SWITCH), FR-147/148/149/150 (IR/POWER SWITCH) PRINTED WIRING BOARDS Ref. No.: SW-314/315/316/317 board and FR-147/148/149/150 board; 4,000 series

DVP-S525D

DVP-S725D

There are few cases that the part isn't mounted in this model is printed on this diagram. DVP-S525D FR-147/150 BOARD CN001 CN002 CN003 D001 D002 D003 D004 D071 IC051 Q001 Q002 B-3 A-5 A-2 A-4 A-4 B-4 A-4 A-1 A-1 A-3 A-3(ON/STANDBY)

SW-314/317 BOARD

SW-315/316 BOARD SW-315/316 BOARD(SIDE A)(SIDE B)

FR-147/150 BOARD1 2 3

A

D098,S098 VES

D098,S098 VIRTUAL 3D SURROUND

1105

1205

1205

B05

11 (11)

(11)SW-314 : 1-672-267SW-317 : 1-672-240-

(12)SW-315 : 1-672-251SW-316 : 1-672-256-

(12)SW-315 : 1-672-251SW-316 : 1-672-256-

1

2

3

4

FR-147 : 1-672-266FR-150 : 1-672-239-


DVP-S725D

FR-148/149 BOARD(SIDE

A)

12 (12)FR-148 : 1-672-250FR-149 : 1-672-25505


FR-148/149 BOARD(SIDE1 2

B)

FR-148/149 BOARD (SIDE B)

3

MS-29 (LOADING)


CN001 CN002 CN003 D001 D002 D003 D004 D071 IC051 Q001 Q002

B-3 A-5 A-2 A-4 A-4 B-4 A-4 A-1 A-1 A-3 A-3

A


(ON/STANDBY)

B05

12 (12)

4-97

14-98

2

3

4

FR-148 : 1-672-250FR-149 : 1-672-255-

SURROUND SWITCH, IR/POWER SWITCHSW-314/315/316/317, FR-147/148/149/150


SW-314/315/316/317 (SURROUND SWITCH), FR-147/148/149/150 (IR/POWER SWITCH) SCHEMATIC DIAGRAM Ref. No.: SW-314/315/316/317 board and FR-147/148/149/150 board; 4,000 series

DVP-S525D/S725D

4-100

SURROUND SWITCH, IR/POWER SWITCH4-99

SW-314/315/316/317, FR-147/148/149/150


HP-108/109/110/111 (HEADPHONE) PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAM Ref. No.: HP-108/109/110/111 board; 2,000 series There are few cases that the part isn't mounted in this model is printed on this diagram.

DVP-S525D/S725D DVP-S525D

HP-108/111 BOARD

K A

K

K A K

11 (11)HP-108 : 1-672-268HP-111 : 1-672-241-

05

LEVEL PHONES MIN MAX

DVP-S725D

HP-109/110 BOARD(SIDE

A)

HP-109/110 BOARD(SIDE

B)

K A

K

K A

12 (12)HP-109 : 1-672-252HP-110 : 1-672-257-

05

K


12 (12)HP-109 : 1-672-252HP-110 : 1-672-257HP-108 (S525D: EXCEPT Australian) HP-109 (S725D: Australian) HP-110 (S725D: EXCEPT Australian) HP-111 (S525D: Australian) (HEADPHONE)

05

LEVEL PHONES MIN MAX

MS-29 (LOADING)



HP-108/109/110/111

HEADPHONE4-101 4-102


RY-12 (RELAY) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM Ref. No.: RY-12 board; 2,000 series There are few cases that the part isn't mounted in this model is printed on this diagram. DVP-S725D

RY-12 BOARD

DVP-S725D

1

3

2

1

1105

1-672-888-

(11)




MS-29 (LOADING)



RELAY4-104

4-103

RY-12


HS-030SH (SWITCHING REGULATOR) PRINTED WIRING BOARD Ref. No.: 030SH board; 6,000 series There are few cases that the part isn't mounted in this model is printed on this diagram.HS-030SH BOARD CN101 CN102 CN201 CN202 CN203 D101 D102 D104 D105 D131 D132 D133 D135 D182 D183 D184 D185 D211 D212 D311 D401 D402 D511 D611 IC301 IC401 Q101 Q102 Q103 Q131 Q181 Q182 Q183 A-3 C-4 A-1 B-1 B-1 C-4 A-3 A-3 A-2 A-2 A-2 A-3 A-3 C-2 C-2 C-2 C-3 B-1 B-2 A-2 C-1 C-1 B-2 B-2 A-2 C-1 B-3 A-3 B-3 A-2 C-2 C-3 C-2



MS-29 (LOADING)



SWITCHING REGULATORHS-030SH4-105 4-106


HS-030SH (SWITCHING REGULATOR) SCHEMATIC DIAGRAM Ref. No.: HS-030SH board; 6,000 series

1

2

3

4! T101D211 S2L20U

5B+L211 10uH P211 500mA 60V

6!

7B+CN201 8P 1 +3.3V +5V GND +12V GND -12V E+5V GND 2

8AU-209 BOARD B301 :S325/S525D:EXCEPT AUS (SEE PAGE 4-45) AU-210 BOARD CN404 :S725D:AUS (SEE PAGE 4-53) AU-211 BOARD CN404 :S725D:EXCEPT AUS (SEE PAGE 4-61) AU-212 BOARD B301 :S525:AUS (SEE PAGE 4-67)

HS-030SH BOARDAC112 0.047uF 630V 435 C113 47pF 2kV Q103 2SK2333 SWITCH 314 R152 0.22 R131 R135 2.2k 2.7k R133 D131 1k 1SS270A L150 45

B+C211 + 330uF 35V D311 21DQ04

B+

C213 + 47uF 35V

B+ B+L311 10uH P311 ! 2.0A 60V + C313 47uF 35V P611 ! 1.5A 60V R211 10 2W

3 4 5 6 7 8

B-

314 S

C110 + 56uF 400V

R104 3.3M 1/2W

314 Q101 2SK2333 SWITCH 3.1

C131 + 10uF 50V

R132 22k D135 1SS270A D133 RD2.7ESB2 9.0

C132 + 1uF 50V 3.1

C116 0.01uF 50V D104 2.4V -0.1 Q102 2SC3377 SWITCH C115 0.033uF

R116 220 1/2W

D611 D3S4M

+

C611 560uF 35V

+

C311 330uF 35V

L611 39uH

+

C613 47uF 35V

CN202 7P 7 6 5 4 +3.3V +3.3V +5V GND GND M+12V A+12V MB-82/85 BOARD CN001 (SEE PAGE 4-39)

S C117 0.0033uF

R112 4.7k R113 680 R110 3.9k

B

B+

R134 10k Q131 2SC3377 POWER CONTROL R186 (SHORT)

D105 1SS270A

B-

B+

R115 27k

D102 RD18FB2

0

D132 1SS270A

R114 2.2k

R301 68

C511 + 1000uF 25V

D212 RD24FB2 L511 10uH

+

C512 47uF 35V

3

P511 750mA 60V

!

2 1

CN203 6P 1 P-CONT E+5V +5V GND -12V GND FR-147/148/149/150 BOARD CN001 (SEE PAGE 4-99) 2 3 4 5

D511 S2L20U

BR713 1k

R304 1.5k

PC103 TLP721F

!

BR303 1k 4 + 2.5 IC301 AN1431T C301 1uF 50V

6

PC101 TLP721F

!

IC301SHUNT REG

R305 (SHORT)

C+ C186 1uF 400V R187 180k 1/2W R188 180k 1/2W

Q183 2SK2663 SWITCH 448 C181 2200pF 1kV 314 C185 0.01uF R189 15k R182 330 1/2W D182 RD2.7ESB2 R184 3.3k D183 1SS270A

! T102

R306 1.5k

314 S

D401 11EQS04

B+

314 Q181 2SK2663 SWITCH

C183 0.0022uF 1.2 S

L182 RS204

C182 0.0033uF

C401 + 100uF D402 35V RD7.5ESB1 R183 2.2k

D184 D1N60 R181 27k

D!F101 1.6A 250V

D185 Q182 RD18 2SC3377 FB2 1.2 SWITCH -0.3 C184 0.0047uF

R185 5.6k

R401 68

CN101 2P 1

L101 ! 18mH

L102 ! 18mH

AC IN

!

!C101 0.1F 250V

R101 1M 1/2W

!C102 0.1F 250V

D101 S1WBAO60

PC102 TLP721F

!

R402 1k C402 + 1uF 2.5 50V

R403 1.2k

IC401SHUNT REG

3.9 IC401 AN1431T

R404 270

2

R405 1.5k

ECN102 2P 1 RY-12 BOARD CN101 (SEE PAGE 4-104) 2 05

C103 330pF 250V

!

C104 330pF 250V

!

C107 330pF 250V

!


SWITCHING REGULATOR4-107 4-108 E

HS-030SH

5-1. SYSTEM CONTROL PIN FUNCTION (MB-82/85 BOARD IC202)

Pin No.

Pin name

I/O

Function

1 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 DREQ1 DREQ0 INT3 SC1 GND X1 X0 VCC5 INT1 INT0 PB0 PB1 PB2 PB3 PB4 DACK1 DACK0 O O I I I O O I I I I O O O O SI2 SO2 PF7 I O O SI1 SO1 I O SO0 SC0 O O AN3 SI0 I I AN1 AN2 I I Set of mode 1 Set of mode 2 Set of mode 3 (fixed at H) Serial data input from IF CON and EEPROM Serial data output to IF CON and EEPROM Serial clock output to IF CON and EEPROM Serial bus 1 (for data input) Serial bus 1 (for data output) Serial bus 2 (for data input) Serial bus 2 (for data output) Reset signal output Output of DMA-ACK 0 to AV DEC Output of DMA-ACK 1 to AV DEC Input of DMA-REQ 0 from AV DEC Input of DMA-REQ 1 from AV DEC Input of interrupt from HGA Serial clock output Ground Clock output (12.5MHz) Clock input (12.5MHz) Power supply Input of interrupt ARP and SERVO DSP Input of interrupt from AV DEC AGND AN0 I Ground Set of mode 0 AVCC AVRH Power supply Reference power supply (+3.3V)

PB5

O

Analog filter gain control

Pin No. 68

Pin name EOP0

I/O I

Function Not used

2 3

PB6 PB7

O O

VES gain control H: VES Rear CH boost control H: rear boost

4 5

VCC3 CLK

O

Power supply CPU clock out (25 MHz)

6 7

CS5 CS4

O O

Not used Chip select signal for ARP, SERVO DSP and HGA

8 9

CS3 CS2

O O

Chip select signal for SDRAM and AV DEC Chip select signal for REG and AV DEC

10 11

CS1 CS0

O O

Chip select signal for external SRAM Chip select signal for external FLASH ROM

12 13

NMI HST

I I

Not used (fixed at H) Not used (fixed at H)

14 15 16

RST GND MD0

I I

Reset signal input from IF CON Ground Input of mode select 0 (fixed at 1)

DVP-S325/S525D/S725D SECTION 5 IC PIN FUNCTION DESCRIPTION

5-1 E

17 18

MD1 MD2

I I

Input of mode select 1 (fixed at 0) Input of mode select 2 (fixed at 0)

19 20

RDY P81

I I

Wait signal input Test terminal (fixed at H)

21 22

P82 RD

I O

Test terminal (fixed at L) Read enable signal output

23 24

WR0 WR1

O O

High byte write enable signal output (16 bit and 8 bit) Low byte write enable signal output (16 bit only)

25-32 33-39

D16-D23 D24-D30

I/O I/O

Data bus D0-D7 (16 bit) Data bus D8-D14 (16 bit), D0-D6 (8 bit)

40 41

GND D31

I/O

Ground Data bus D15 (16 bit), D7 (8 bit)

42 43

A00 VCC5

O -

Address bus A0 Power supply

Rear panel lime input select (H: DISC L: EXT) Chip select signal to IF CON Chip select signal to DAC (Lt and Rt) Chip select signal to DAC (L and R) DVD/CD select (H: 44.1kHz L: 48kHz)

44-64 65

A01-A21 GND

O -

Address bus A1-A21 Ground

66 67

P66 P67

O I

PLL IC control output H: DOUBLE DIAG mode signal input L: DIAG

DVP-S325/S525D/S725D SECTION 6 TES

sony dvp-s325 dvp-s525d dvp-s725d

Documents

s725d phono

w s725d

s725d digital

s725d s video

s725d dvd pcm

db audio

db line

khz sampling frequency