sonora sd-pi-6s-t directv slimline polarity locker and power inserter
DESCRIPTION
Sonora SD-PI-6S-T Spec SheetTRANSCRIPT
S I T U A T I O N
F E A T U R E S
D E S C R I P T I O N
A P P L I C AT I O N N O T E S
SS I T U A T I O N
FF E A T U R E S
D E S C R I P T I O N
AA P P L I C AT I O N N O T E S
Contact: Sonora Design Associates 805.644.8913 www.sonoradesign.com [email protected]
Revised Jun 2 2011
POWER SUPPLIES
SOLUTION
RELATED CONSIDERATIONS
SD
PI-6
S P
OL
AR
ITY
LO
CK
ER
The signals from a DIRECTV® (4) polarity SLSP-F
SlimLine® dish with SL5 LNB, DTV66E 95º dish and
a possible 6th polarity are required for multiple
switches.
Model SD PI-6S powers a DIRECTV® SL5 LNB, polarity
locks the four dish outputs and provides (2) 20 V
outputs to power the 95º LNB on the DTV66E dish
and a possible future polarity.
Line powered amplifiers may be powered by the
power inserter. A total of 2 amps of DC is available
from the short circuit protected power transformer.
• DBS Compatibility . . . . . . . . . . . DIRECTV®SL5, 95º & Flex2
• 2 Amp Power Supply . . . . . powers LNBs & line amplifiers
• Power LEDs per polarity . . . . . . green if NO short circuits
• Locks SL5 LNBs . . . . . . . . one polarity on each of (4) coax
• Indoor / Outdoor case . . . . . . . . . . . . . . Die cast Aluminum
DIRECTV® SlimLine® SL5, 95º Ku/Ka and FLEX2
polarity locker and power inserter.
FLEX 1 FLEX 2
FLEX 1 FLEX 2
SD MST612
DC
SD SA-6ALFLEX 1 FLEX 2
FLEX 1 FLEX 2
DC
SD PI-6S
FLEX 2
FLEX 1 FLEX 2
PS242000A
CA24RIN DC OUT
10199
SL5103
110 119 worldDIRECT10195
Legacy 1
Legacy 3
Legacy 2
OFF-AIR
SWM1 PWR
SWM2
SWM8
99º/101º
103º/110º/119º
18V 13V18V22k
13V22k
FlexPort1
FlexPort2
Blocks
Locks
Powers
Amplifies
Model SD PI-6S provides voltages and control signals
to power and polarity lock the LNBs’. The (2) amp power
supply has suffi cient current to power model SD SA-6ALand model CA24R amplifi ers.
DC voltage indicator LEDs on the SD PI-6S glow
orange for 20 volts and green for 14 volts. A single
unlit LED indicates a short circuit on the input.
M u l t i - t a p m o d e l s S D M S T 616 , S D M S T 612 , SD MST609 and SD MST606 extract a portion of the
trunk signal to feed DBS switches.
S P E C I F I C A T I O N SSS P E C I F I C A T I O N S
Contact: Sonora Design Associates 805.644.8913 www.sonoradesign.com [email protected]
Revised Jun 2 2011
Specifi cations ....................... Typical ..................QC Limit
Inputs / Outputs ........................................... (5) @ 5 to 2400 MHz
Insertion Loss.................................. 0.5 dB ............................... 1 dB
Return Loss 54-2400 MHz .......... 12 dB ..............................10 dB
Power Specifi cations
Power Transformer ................................................24 VDC, 2 Amp
100 to 240 VAC input, switching, short circuit protected
Output Voltages and tones
101º& 99º (Even) LHCP ..................................................19.4 Vdc
101º & 99º (Odd) RHCP .................................................13.4 Vdc
119º & 103º (Odd) RHCP ........................... 22 kHz & 13.4 Vdc
110º/119º & 103º (Even) LHCP ................. 22 kHz & 19.4 Vdc
FLEX1 & 2...........................................................................19.4 Vdc
Mechanical Specifi cations
Dimensions ...................................................8.5”L x 5.4”W x 0.9”H
Weight .........................................................................1.5 lb (0.7 kg)
Master Carton (8 units) ................................................12” x 9” x 9”
Master Carton Weight ..............................................16 lb. (7.2 kg)
Environmental Specifi cationsOperating Environment: ....................................Indoor/Lockbox
Ambient Temperature .......................................... -30º C to +60ºC
POWER SUPPLIESS
D P
I-6S
PO
LA
RIT
Y L
OC
KE
R
250 .MHz. . . . . . . . . . . . . . . . . . . . . . . . . . 750 . .950 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1450 . . .1680 . . . . . . . . . . . . . . . . . . . . . . . . . . . 2150DISH
9506 99ºc 99ºs
DIRECTV® SL5 LNB Ka / Ku Frequency PlanUpdated:
Sept 15, 2011
101º 9501
111753
31
29
27
25
23
21
19
17
15
1391
11753 1 53131517192123913V
9507 99ºc 101º9502
212864
32
30
28
26
24
22
20
18
16
14
102
12864 2 64141618202224
10
18V
103ºca 9508103ºcb951013V & 22kHz 1 9753 9
131517192123
11
119º 9513
1 97531113151719212325272931
21
19
11
131517
23
103ºca9511 103ºca 9509110º 9512 119º 9514
2 12864 3
230
28
26
24
22
20
18
16
14
102
1286416182022
10
18
16
14
202224
18V & 22kHz
12
10
24 864
3 5 7
Receivers selecting 99º or 101º odd generate 13V.
Receivers selecting 99º or 101º even generate 18V.
Receivers selecting 103º or 119º odd transponders
generate 13V & 22 kHz.
Receivers selecting 103º, 110º or 119º even transponders
generate 18V & 22 kHz.
Cables from the Polarity locker outputs must match switch input voltages: 20V to 18V, 14V to 13V, 20V/22k to 18V/22k 14V/22k to 13V 22k.
DIRECTV® provides test channels to verify the
reception of each satellite. The test channel numbers
associated with the bands of transponders is provided.
T he most common problem for instal lers is
maintaining the correct trunk to switch polarity. Use
the test channels to verify trunk polarity.
DC
SD PI-6S
FLEX 2
FLEX 1 FLEX 2
PS242000A
13 1322k
1822k
18 FLEX1
FLEX2
WB68Switch
Blocks
Locks
Powers
Contact: Sonora Design Associates 805.644.8913 www.sonoradesign.com [email protected]
Revised Jun 2 2011
3SD PI-6S TRUNK POWER INSERTER
Parameter UNIT SD PI-6
Operating Frequency Range MHz 250 - 2150
Insertion Loss dB 1.5 (max.)
Flatness in operating frequency range dB ± 0.5
Number of Input Ports Each (6) SCTE Indoor F
Number of Output Ports Each (6) SCTE Indoor F
Isolation between ports dB > 35 dB
Input / Output Return Loss dB > 10 (min)
DC Power provided to inputs VDC
Port #1 (20 V 101º & 99º) VDC 20 ± 0.5
Port #2 (13 V 101º & 99º) VDC 13.5 ± 0.5
Port #3 (22 kHz & 20 V 119º & 103º) VDC 20 ± 0.5 (+ 22 kHz)
Port #4 (22 kHz & 13 V 119/110º & 103º) VDC 13.5 ± 1 (+ 22 kHz)
Port #5 (Flex Port 1) VDC 20 ± 1 or 13.5 ± 1
(Internally switch able)
Port #6 (Flex Port 2) VDC 20 ± 1 or 13.5 ± 1
(Internally switch able)
LED Color corresponding to: GREEN
AMBER
VDC
VDC
10.0 - 14.5
17.0 - 20.5
Number of LEDs Each 7 (1 per input & 1 for adaptor input)
22 kHz Tone to ODU kHz
Frequency kHz 22.0 ± 0.5
Duty Cycle % 50
Amplitude mVpp 800 (min)
DC Power Path mA 1000 (max.) From DC Input to each
Input
DC Power Connector Type Each (1) SCTE Indoor F
Switching Mode Power Supply 24 V, 1.2 A (min)
Short Circuit Protection Yes, 1 A Multi fuse
Lightning Surge Protection 32 V p-p, max shunt current 200 A;
8 msec, 1.5 kW max dissipation
Ground Screws Each 2 Green Screw Ground pt.
Dimensions L x W x H mm 136 x 217 x 23
Environmental Requirements Indoor use only
Operating Temperature range ºC -34 to + 60 Indoor housing
Humidity Shall survive 95% relative humidity
over operating temperature
MDU switch able Power Inserter and Tone Generator UnitSimplifi es MDU installations by providing an integrated module for
locking LNB polarizations and satellite selection
SD PI-6S Trunk Power Inserter
• Powers SL5, 95W & FLEX2 ODUs
• Regulated DC Voltages
• F-Connector Power Input
• Dual 10 AWG Ground Lugs
• Dual Color LED Indicators
PS242000A DC Power Supplies
• UL Approved
• 24 Volt 2 Amp
• Interchangeable AC Cord
• F-Connector for DC Input
• Overload Protection
Contact: Sonora Design Associates 805.644.8913 www.sonoradesign.com [email protected]
Revised Jun 2 2011
4POWER SUPPLIES
DIRECTV® recommends that the distance between
receiver and dish be less than 150 feet of solid copper
RG-6. Here is why.
Model SL5 LNBs employ current management to
minimize the current carried per coax. (540 mA total)
18 V = 220 mA, 18V 22kHz = 220 mA, 13V = 50 mA,
13V 22kHz = 50 mA.
The 18 volts originating at the SWM8 must arrive
at the SL5 above 16 volts for the SL5 to operate
correctly. Up to (2) volts can be lost in the coax.
Current x Resistance = Voltage loss
Solid copper RG-6 has a typical loop resistance of
4 ohms per 100 feet. At 200 feet the resistance is 8
ohms. 0.22 Amp x 8 ohms = 1.76 volts loss
18 V - 1.76 V = 16.4 volts to the SL5
Model SD PI-6S-T starts with 19.4 Volts to provided
extended dish to Main Point of Entry distances.
The extra voltage provides an additional 150 feet
RG-6 distance. Model LA145a off sets the signal loss
of 150 feet of RG-6.
The LA145a located at the polarity locker does not
aff ect the current loss in the cable to the dish. What
is the voltage loss in the 18v coax?
At 350 feet the resistance is 12 ohms.
0.22 Amp x 12 ohms = 2.64 volts loss
19.4 V - 2.64 V = 16.76 volts to the SL5
18 Vdc, 0.22 Amp
16 Vdc Minimum
SWM8 Powering of SL5
24 Vdc
Legacy 1
Legacy 3
Legacy 2
OFF-AIR
SWM1 PWR
SWM2
SWM8
99º/101º
103º/110º/119º
18V 13V18V22k
13V22k
FlexPort1
FlexPort2
24V2A
HRPIR242B
10199
SL5103
110 119
200 ft RG-64 ohms / 100 ft
worldDIRECT10195
I = 220 mAV= 19.4 - (12 x .22)V = 16.76
19.4 V @ SD PI-6S
300 feet RG-6@ 4 ohms / 100ft= 12 ohms
10199
SL5103
110 119worldDIRECT10195
DC
SD PI-6S
FLEX 2
FLEX 1 FLEX 2
PS242000A
LA145A
DCIN 5IN 4IN 3IN 2IN 1
OUT5OUT4OUT3OUT2OUT1 DC
5S
AT
PL
PO
LA
RIT
Y L
OC
KE
R
Contact: Sonora Design Associates 805.644.8913 www.sonoradesign.com [email protected]
Revised Jun 2 2011
5POWER SUPPLIES
SWM8 to SL5 Communication
Multiple SWM8’s talking to the SL5 creates strange fi eld
problems that can be attributed to 22 kHz phasing.
Multiple 22 kHz signals when combined can create
constructive and destructive interference. 180º out of
phase combining will reduce the 22 kHz signal to zero!
The following web location has a live demonstration
on the aff ects. http://www.kettering.edu/~drussell/
Demos/superposition/superposition.html
Model SD PI-6S-T polarity locker located between
the splitters and LA145a amplifi er blocks the 22
kHz signals generated by multiple switches and
generates a fresh set of voltages and 22 kHz tones .
Legacy 1
Legacy 3
Legacy 2
OFF-AIR
SWM1 PWR
SWM2
SWM8
99º/101º18V 13V
18V22k
13V22k
FlexPort1
FlexPort2
Legacy 1
Legacy 3
Legacy 2
OFF-AIR
SWM1 PWR
SWM2
SWM8
99º/101º18V 13V
18V22k
13V22k
FlexPort1
FlexPort2
Legacy 1
Legacy 3
Legacy 2
OFF-AIR
SWM1 PWR
SWM2
SWM8
99º/101º
103º/110º/119º
18V 13V18V22k
13V22k
FlexPort1
FlexPort2
HRvS4 HRvS4 HRvS4
PI-28
PI-28
PI-28
HRvS4
101
99
103
110 119
HRvS4
worldDIRECT10195
DC
LA145a
SAT1
OUT1
OUT4
OUT3 DC
SAT4
SAT3
OUT5
SAT5
OUT2
SAT2
0 V
DESTRUCTIVE PHASE SHIFT 22 KHZ
CONSTRUCTIVE PHASE SHIFT 22 KHZ