1

SOMNI

Instructions for use

Somni mask is the easiest way to lucid dreaming

2

FIRST LAUNCH

SOMNI

button

In order to turn on SOMNImask® you need to

hold down the device button for two seconds

and release. After that, the indication of the

remaining battery will begin

Recommendations can be read here: https://somni.org/button/

When the device is working, press the button for more than 2 seconds, and the device will go into off mode. Before that, it will show the remaining battery charge.

The battery charge is shown based on the LED color when

the device is turned on or off.

- Green means full battery power remaining.

- Yellow means half the remaining battery charge.

- Red means low battery.

The mask has a test mode function. To enable this mode hold

the button for 7 seconds and release, then LED will blink with different colors, and device will start playing Lucid.mp3, this function is needed to test brightness of lights and sound volume.

3

You can connect headphones to the device. In order, to connect

headphones, you need to insert the headphone jack into the input

of the device. Audio input can be seen on the picture

There is only one button for

the device and it’s located on

the top of the device. With the

button you can turn the device

on or off and also test the

audible light signals.

SOMNI

button

audio input

jack 3.5mm

There are no speakers built into the device. In order to hear audio

files that are in the device’s memory. You need to connect headphones

to the audio input. Only audio files: Calm.mp3, Lucid.mp3, Alarm.mp3

can be played through the headphones.

Remember, one earbud is shorter than the other.

Put on a short ear piece that is closer to your

side of the ear

4

eye deviceAn eye device is positioned in the eye socket of the mask to record eye

movement. Eye sensors are located in the device window.

The mask completely blocks out the light inside for effective tracking

of eye movement. The device has an accelerometer sensor for head

tracking. In order, for the sensors to record eye movement, you need

to wear the eye mask tightly.

Once you have plugged in the headphones, put on the mask and you are

ready for bed. Firstly, the mask will play a calm melody and then go intosleep mode so as not to disturb you during deep sleep phases. After the

Calm pause time, eye tracking will begin to recognize for REM sleep. If REM

sleep has been detected, the device will turn on Lucid audio and RGBsignals. During REM sleep, you may notice these signals in your dream.

Before using the device for the first time, charge the device for 20 minutes.Then connect the headphones, put on the mask, hold down the button for 2seconds and release. Your device is turned on if a calm melody is playingthrough the headphones.

Tip: You do not need to wear a mask before falling asleep, turn on the maskand put it next to you and put it on at any time of sleep.

For effective use of the mask, put on the mask 1-2 hours before waking upcompletely.

5

SETTINGS

In order to charge or connect the device to a computer, you need to

connect the device and the computer with the USB wire.

Easily insert the connectors as shown on the picture below.

At the bottom of the device is the micro-USB input, this device

input has these functions: charging the device and connect to

a computer or USB-OTG

micro-USB input

SOMNI

After that you can start charging the device or configure it.

To start charging or setting up you need

to hold down the button for 2 second and release

6

After pressing the button you will see the automatic opening of the main memory window of the device. It works like a USB flash drive.

The main memory of the device looks like the photo below

The device plays the original audio files: Lucid, Calm, Alarm (mp3 only)

To start configuring the device you need to go to the device config page at somni.org/program/

After you have gone to the page, you need to click “Upload” button

7

After clicking on the uploadbutton, a window for selectionwill automatically open. Select“USB Drive” from the list, thengo to the “Configs” folder andselect the “default.txt” file, thenclick Open.

After you have opened the default.txt configuration file, you will see the configuration page. Follow the instructions on the page and adjust the setings for your convenience.

After setting up, click the “Save settings” button and followthe instructions below

8

In order to replace the original audio files you need to move your audio to the main memory of device. For example file “my.mp3”

Then assing this audio in the “default.txt” file. Just go to the Configsfolder and open the “default.txt” file, then rename the old parameter“fileLucid Lucid.mp3” to “fileLucid my.mp3” and save the file.