soil exploration part ii t.e. civil 2009-2010 g.e.- i
TRANSCRIPT
![Page 1: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/1.jpg)
Soil Exploration Part II
T.E. Civil 2009-2010
G.E.- I
![Page 2: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/2.jpg)
Topics Covered Introduction Methods of investigation Methods of boring Soil samplers and sampling Location and number of pits and borings Penetrometer tests Borehole logs Geophysical methods
![Page 3: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/3.jpg)
Methods of SamplingSamples
Disturbed Undisturbed
(The structure of the soil is disturbed (The true in-situ structure and water content
to a considerable degree) is retained as closely as possible)
Remoulded Representative Block Drive
Wash
![Page 4: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/4.jpg)
Methods of Sampling Disturbed samples used for determining index properties (ex.
gsd, consistency, etc.) Undisturbed samples used for determining engineering
properties (ex. Density, water content, shear strength parameters, etc.)
Wash samples obtained from wash boring water or mud. Representative sample retains all constituents of the soil, but
is disturbed from natural state and structure. (ex. Split spoon sampler)
Block samples are carved out form sides or bottoms of excavations, sealed in a box and taken to lab.
Open drive samplers consist of thin walled tubes which are driven or pushed into the soil at the bottom of the hole. (ex. Shelby Tube sampler)
![Page 5: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/5.jpg)
Undisturbed Samples
![Page 6: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/6.jpg)
Methods of Sampling
Thin-wall open-tube samplers (Shelby Tube Samplers) are used for soils that are particularly sensitive to sampling disturbance. They are suitable for fine soils up to a firm consistency, and free from large particles.
Shelby Tubes are available in carbon steel and in stainless steel. Usual diameters are 3" or 4" OD.
![Page 7: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/7.jpg)
Shelby Tube
![Page 8: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/8.jpg)
Split spoon sampler IS:9640-1980
![Page 9: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/9.jpg)
Sketch of split spoon sampler
![Page 10: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/10.jpg)
Methods of Sampling
Requirements to minimize disturbance to samples Area ratio = (D2
w-D2e) x 100%
D2e
Area ratio should be as low as possible. (<10%).
It represents the amount of soil displaced.
Inside clearance = (Ds-De) x 100%
ratio De
.
![Page 11: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/11.jpg)
Methods of Sampling
The inside clearance allows elastic expansion of the sample and minimizes frictional drag on the sample.
The inside clearance should be between 0.5% to 3%. The outside clearance = (Dw-Dt) x 100%
ratio Dt
Outside clearance is necessary to reduce the driving force and resistance to withdrawal.
The outside clearance should be between 0% and 2%. Diameter of samples should not be less than 38mm.
(Generally between 50-150mm). Piston sampler (Osterberg sampler) not covered. Please
refer to any book.
![Page 12: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/12.jpg)
Rock coring
Sampler consists of core barrel and bit is coring bit.
Core barrel – single tube or double tube of various dia: EX, AX, BX, NX, etc.
Recovery = Length of sample recovered x 100%
Length of run RQD = Length of samples >= 4” x 100 %
Length of run
![Page 13: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/13.jpg)
![Page 14: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/14.jpg)
SPT (Standard Penetration Test) IS:2131 – 1981 Method for Standard
Penetration Test for Soils. Most important and most commonly used
field test Typical equipment: drill rig, split spoon
sampler, hammering equipment, casing pipe.
![Page 15: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/15.jpg)
SPT Procedure Procedure:
1. Drive a section of casing pipe.2. Complete wash boring and clean the hole3. Replace driving bit by split spoon sampler at the bottom end of the
driving rod4. Drive the sampler by dropping a hammer of 63.5kg weight through a
height of 75 cm5. The number of blows required to penetrate three successive lengths
of 15 cm are noted.6. The first 15 cm drive is considered as seating load and is ignored.
The total number of blows required to penetrate the remaining 30 cm is called the blow count or penetration number N.
7. Raise the sampler to the surface, open it and extract the sample. 8. Drive the next length of casing and repeat the process until required
depth is reached.9. At the end of the borehole, note the gwt after it stabilizes and then
backfill the borehole.
![Page 16: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/16.jpg)
Corrections to N value
Overburden Correction applied to N value based on chart by Peck, et. al. (varies from 0.45 to 2) N’=Cn * N where Cn is correction factor
Correction due to dilatancy for fine sand and silt below gwt having N’ > 15 N” = 15 + 0.5*(N’-15)
![Page 17: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/17.jpg)
Correlations between N values and soil properties
N CompactnessRelative Density (%)
o
0 to 4 Very Loose 0-15 < 28
4 to 10 Loose 15 - 35 28 -30
10 to 30 Medium Dense 25 - 65 30 -36
> 50 Very Dense > 85 > 41
![Page 18: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/18.jpg)
Correlations between N values and soil properties
Consistency N qu (kPa)
Very Soft 0 to 2 < 25
Soft 2 to 4 25 to 50
Medium Stiff 4 to 8 50 to 100
Stiff 8 to 12 100 to 200
Very Stiff 15 to 30 200 to 400
Hard > 30 > 400
![Page 19: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/19.jpg)
Other test methods
DCPT – Dynamic cone penetration test IS:4968 -1976 (Method for subsurface sounding for soils: Parts I and II)
CPT – Static Cone Penetration Test (Method for subsurface sounding for soils: Part 3 Static cone penetration test)
Plate Load Test (Method of Load Test on Soils)
![Page 20: Soil Exploration Part II T.E. Civil 2009-2010 G.E.- I](https://reader033.vdocuments.mx/reader033/viewer/2022061305/551421ed5503466d1a8b48d2/html5/thumbnails/20.jpg)
Borelog and geotechnical investigation report.