smc-50 solid-state smart motor controller selection guide · 2017. 12. 6. · specifications........

Selection Guide

SMC™-50 Solid-State Smart Motor ControllerBulletin 150

Bulletin 150

SMC™-50 Smart Motor Controllers

2Visit our website: www.rockwellautomation.com/catalogs

Publication 150-SG010E-EN-P

Overview

Features

SMC™-50 §

200…690V90…520 A

Soft Start S

Linear Acceleration/Deceleration S

Torque Control S

Kickstart S

Pump Control S

Current Limit S

Dual Ramp Start S

Full Voltage S

Energy Saver S

Soft Stop S

Preset Slow Speed S

SMB™ Smart Motor Braking S

Accu-Stop™ Δ S

Slow Speed with Braking S

Integrated Bypass Contactor NA ♣Integrated Motor Overload Protection S

Single-phase Operation —

DPI Communication S

Metering S

Real Time Clock S

Energy Saver Mode S

Motor Winding Heater Function S

Diagnostic Faults & Alarms S

Individual Bit Enable of Faults & Alarms S

Automatic Tuning of Motor Parameters S

Parameter Configuration/Programming Tools —

Human Interface Module (HIM) O

Parameter Configuration Module O

Software: Connected Components Workbench, DriveExplorer™, andDriveExecutive™ O

Digital I/O Expansion Module‡ O

Analog I/O Expansion Module‡ O

Ground Fault/CT/PTC Module ‡ O

Network Communications O

Inside-the-Delta Functionality S

DeviceLogix™ S♠Product Selection Page 15

S = Standard FeatureO = Optional Feature�The starter does not include a configuration device as standard.‡ With removable terminal block.§ The starter ships with two 24V DC control inputs and two relay outputs as standard. ♣ The SMC-50 Starter is fully solid-state (no integrated bypass). An external bypass contactor can be added as an option.Δ Accu-Stop is not included as a parameter/function like that of the SMC-Flex. However, the Accu-Stop function can be accomplished with the Stop Option and

Slow Speed with Braking functions.♠ Firmware rev. 4.XXX and higher.

Bulletin 150




Bulletin 150 — SMC™-50 Smart Motor Controller

Certifications

Selection Guide

Product Overview

Product Overview

Status LED

Bezel for Optional 20-HIM-A6

Port 7

Port 8

Port 9

Reset/Test

� 90…520 A range� Nine standard start modes� Rated voltage: 200…690V AC� Three expansion ports to install option modules� Fully solid-state, continuous SCR control� Built-in electronic motor overload protection� Current and voltage sensing on each phase� Metering� DPI Communication Protocol� Parameter configuration options� Energy saver mode� Logging of the last 100 events with time stamp� Network communication (option)� External bypass as an option� Conformally-coated PCBs

The SMC-50 Smart Motor Controller is a micro-processor basedsoft starter designed to maximize the efficiency of motor startsand stops. Featuring a fully solid-state design, the SMC-50 usessix SCRs (two per phase), which are always engaged (nointernal bypass) to vary the conduction period and control thevoltage (torque) to the motor during starting, running, andstopping. The starter has many advanced power monitoring andmotor/starter protection features to help increase overallreliability. Product scalability is enabled by its three connectionports (Port 7, 8, & 9) to house additional I/O, networkcommunication, or parameter configuration modules (amaximum of three modules). Scalability continues into theconfiguration of the controller via three different options: (1) aparameter configuration module with limited configurationcapability using DIP and selector switches, (2) a multilingual 20-HIM-A6 controller or a panel-mount keypad with LCD displayfeaturing more advanced configuration features, and (3)software that is PC based and network capable (e.g.,Connected Components Workbench) with optimal configurationfeatures. The SMC-50's front panel features a single, multi-colored LED status indicator which provides both diagnosticsand controller status information as well as a Push-to-Reset/Hold-to-Test push button which allows manual reset of anactual fault condition, and initiates a tuning cycle or test forfault.

Features

The SMC-50 Smart Motor Controller provides microprocessor-controlled,solid-state (SCR, no bypass) starting for standard three-phase squirrel-cage induction or Wye-Delta (6-lead) motors.

UL 508EN 60947-4-2

Table of Contents

Modes of Operation... 4Features.......................... 9Cat. No. Explanation.. 14Product Selection ....... 15Accessories................... 30Specifications............... 34Approx. Dims................ 49

Standards Compliance

This selection guide/catalog provides minimum information needed to select the proper SMC-50 Smart Motor Controller according to themotor ratings used in the application. For normal duty applications (e.g., pumps, compressors, and short conveyors), refer to the Normal DutyProduct Selection tables on page 15 and page 21. For high inertia, heavy duty applications (e.g., rock crushers, wood chippers, centrifugalfans, and long conveyors), refer to the Heavy Duty Product Selection tables on page 18 and page 23. For best selection results in all cases,especially where there is frequent starting and stopping or when it is unclear if the application is Normal Duty or Heavy Duty, it is highlyrecommended that the free selection tools be used (available at http://www.rockwellautomation.com). For additional assistance, please visitwww.rockwellautomation.com or contact Industrial Controls Technical Support by email at [email protected] or by phone at440-646-5800.

cULus Listed (Open Type) (FileNo. E96956)CE Marked per EMC Directiveand Low Voltage DirectiveCCC�C-Tick�GOST-RKCC�ABS

�For updated certification status of controllers with 24V DC control power, consult your local Rockwell Automation sales office or Allen-Bradley distributor.

Bulletin 150




Modes Of Operation

Torque Control Start

This method provides a torque ramp from a user-adjustable, initialmotor starting torque to a user-adjustable, maximum torque overthe defined starting ramp time. The torque control mode provides amore linear starting ramp than a soft start, potentially resulting inless stress on mechanical components and a more time controlledramp. A current limit value is also available to limit the startingcurrent throughout the torque start.

Linear Speed Acceleration

With this type of starting mode, the motor acceleration is at aconstant rate. The controller accelerates the motor in a linearfashion from the off (0 speed) condition to full speed condition in thetime configured in the user-defined ramp time. This is done using aproprietary motor speed feedback algorithm to sense motor speed*.This starting mode presents the least amount of stress onmechanical components. An initial torque value is configured todefine a motor starting value. A current limit value is also availableto limit the starting current throughout the linear acceleration startmaneuver.*NOTE: An external speed sensor is NOT required.

Soft Start

This method covers the most general applications. The motor isgiven an initial torque setting, which is user adjustable. From theinitial torque level, the output voltage to the motor is steplesslyincreased (ramped) during the acceleration ramp time, which isuser-adjustable. A user-adjustable current limit value is alsoavailable. This limits the current throughout the soft start.

NOTE: A motor’s torque curve is not a linear function and dependson both applied voltage and current. As such, if the soft starterramped voltage applied to the motor is sufficient for it to developtorque high enough to overcome the inertia of the load, the motorcould quickly accelerate to full speed in less than the configuredramp time when using the Soft Start mode.

600%

50%

Perc

ent F

ull L

oad

Curr

ent

Time in SecondsStart

Current Limit

Perc

ent V

olta

ge

100%

InitialTorque

Time in SecondsStart Run

Ramp Time

Current Limit

Current Limit

Maximum Motor Torque

TorqueRamp

100%

StartingTorquePe

rcen

t Rat

ed M

otor

Tor

que

Time in SecondsRunStart

Ramp Time

Soft Stop

Starting Modes

Soft Start Pump Control Mode

Linear Speed Acceleration Dual Ramp Start

Torque Control Start Full Voltage Start

Current Limit Start Preset Slow Speed

Selectable Kickstart Integral Motor Winding Heater(starting feature)

Current Limit Start

This method provides a current limit controlled start by maintaininga constant current to the motor and is used when it is necessary tolimit the maximum starting current. The starting current and currentlimit starting ramp time is user-adjustable. Current Limit Start can beused in conjunction with Soft Start, Torque Control, and LinearSpeed Acceleration Starts.

Perc

ent S

peed

100%

LinearAcceleration

LinearDeceleration

Time in SecondsStart Run Stop

Current Limit

Ramp Time

Stop Time

The SMC-50 Smart Motor Controller provides the following starting modes of operation as standard:Starting Modes

Bulletin 150




Modes Of Operation

100%

Perc

ent V

olta

ge

Time in Seconds

Perc

ent V

olta

ge

100%

InitialTorque

Kickstart Time

Coast-to-Rest

Soft Stop

Time in Seconds

Run Soft StopStart

Kickstart Level

100%

Mot

or S

peed

Time in Seconds

Pump StartRamp Time

Run Pump StopStop Time

Dual Ramp Start

This method is useful on applications with varying loads, startingtorque, and start time requirements. Dual Ramp Start gives the userthe ability to select between two separate start profiles via anyprogrammable auxiliary input. Each start profile can use any of theavailable starting modes.

Selectable Kickstart

The kickstart feature provides a boost at startup to break awayloads that may require a pulse of current/torque to get started. It isintended to provide a current/voltage pulse for a short period oftime. Kickstart is available in Soft Start, Current Limit, Pump, andTorque Control modes.

Pump Control ModeThis mode is used to reduce surges in a fluid piping system and theresulting water hammer or check valve slam caused by starting acentrifugal pump at full voltage and full speed. In addition, thismode also reduces pump cavitations, increasing pump life. Toprovide these benefits, the SMC-50's microprocessor generates amotor starting curve which follows the starting characteristics of acentrifugal pump and monitors operation during start to ensurereliable pump starts.

Ramp #2

Ramp #1

Time in Seconds

Perc

ent V

olta

ge

100%

InitialTorque #2

InitialTorque #1

Start #1Start #2

Run #1Run #2

Current Limit 2

Current Limit 1

Full Voltage Start

This method is used in applications requiring across-the-linestarting. The SMC-50 performs like a solid-state across-the-linecontactor. Full inrush current and locked-rotor torque are realized.The SMC-50 may be programmed to provide full voltage start inwhich the output voltage to the motor reaches full voltage in fivecycles.

Bulletin 150




Modes Of Operation

Linear Speed Deceleration

Configuring the motor stop mode to Linear Speed Decelerationmode commands the motor to stop from full speed to zero speedfollowing a linear ramp based on the user-configured stop time. Acurrent limit value is also available to limit the stopping currentthroughout the Linear Speed Deceleration maneuver.

Coast

Configuring the stop mode to coast sets the controller to perform amotor coast-to-stop maneuver.

Time in Seconds

Perc

ent V

olta

ge

100%

InitalTorque

KickstartTime

Coast-to-Rest

Soft Stop

Soft Start

Soft StopStart Run

Ramp Time Stop Time

Preset Slow Speed

This feature/function can be used on applications that require slowspeed moves for positioning material. The Preset Slow Speed canbe set from Low, ± 1%, up to High, ± 15% in 1% increments ofbase speed. Forward or reverse movement is enabled throughprogramming the sign (±) of the percent speed. No reversingcontacts are required. To ensure accurate stops, braking is also apart of this function.

Integral Motor Winding Heater (starting feature)

This function eliminates the need for additional hardware to heat themotor from a cold start and enables using a small amount of motorcurrent switched to each motor phase in sequence to heat thewindings. Heating can be time based or activated by configurableinput. The winding heat level is also configurable.

Soft Stop

The Soft Stop mode can be used in applications requiring anextended stop time. The voltage ramp down time is user-adjustablefrom 0...999 seconds. This load will stop when the programmedstop time has elapsed or the voltage ramp drops to a point wherethe load torque is greater than the motor torque.

Perc

ent S

peed

100%

LinearAcceleration

LinearDeceleration

Time in SecondsStart Run Stop

Current Limit

Ramp Time

Stop Time

Stopping ModesThe SMC-50 Smart Motor Controller provides the following Stopping Modes of operation as standard:

Stopping Modes

Coast Linear Speed Deceleration

Soft Stop Pump Stop

100%

Mot

or S

peed

Time in Seconds

Forward15% - High

1% - Low

Reverse

Start Run

Bulletin 150




Modes Of Operation

7 or 15 %

100%

Mot

or S

peed

Time in Seconds

Braking

Coast-to-Rest

SlowSpeed

Start Run Stop

Braking Control Modes

SMB ⎯ Smart Motor Braking Accu-Stop™

Slow Speed with Braking External Braking Control

100%

Mot

or S

peed

Time in Seconds

Pump StartRamp Time

Run Pump StopStop Time

100%M

otor

Spe

edSmart MotorBraking

Coast-to-Rest

Time in SecondsAutomatic ZeroSpeed Shut-Off

Start Run Brake

StopTime

100%

Braking

Slow Speed

Slow Speed Braking

Coast-to-Rest

Mot

or S

peed

SlowSpeed

Start Run Brake

15%

1%

15%

1%

SMB — Smart Motor Braking�

This mode provides motor braking for applications that require themotor to stop faster than a coast-to-rest. Braking control withautomatic zero speed shutoff is fully integrated into the design ofthe SMC-50. This design facilitates a clean, straight-forwardinstallation and eliminates the requirement for additional hardware(e.g., braking contactors, resistors, timers, and speed sensors). Themicro-processor based braking system applies braking current to astandard squirrel-cage induction motor. The strength of the brakingcurrent is programmable from 0…400% of full-load current.

Slow Speed with Braking�

Slow Speed with Braking is used on applications that require slowspeed (in the forward or reverse direction) for positioning oralignment and also require braking control to stop. Slow Speedadjustments are ±1% (low)…±15% (high) of rated speed. Brakingcurrent is adjustable from 0…350%.

Pump Stop

Just as starting a centrifugal pump at full voltage causes waterhammer and check valve slam, stopping a centrifugal pump that isrunning at full speed can also produce the same results. The SMC-50's Pump Stop mode generates a motor stop curve, which followsthe stop characteristics of a centrifugal pump, which results in thegradual decrease in motor speed.

Accu-Stop� ‡

This control is used in applications requiring controlled positionstopping. During stopping, braking torque is applied to the motoruntil it reaches the configured preset slow speed value (±1…±15%)and holds the motor at this speed until a stop command is given.Braking torque is then applied until the motor reaches zero speed.Braking current is programmable from 0…350% of full-load current.

Braking Control Modes�The SMC-50 Smart Motor Controller provides the following braking control modes of operation as standard:

Bulletin 150




Modes Of Operation

Running Modes

SCR Control — Normal RunOperation

External Bypass — Optional RunOperation

SCR Control — Energy Saver RunOperation Emergency Run

SCR Control – Energy Saver Run Operation

The Energy Saver Run Operation function is typically used inapplications where the running motor is lightly loaded or unloadedfor an extended period of time. With the Energy Saver RunOperation function enabled, the SMC-50 continuously monitorsmotor load using internal feedback to control its SCRs whichreduces the voltage applied to the motor. This will potentially reducepower consumption. A parameter is provided to display thepossible energy saved as a percent.

Emergency Run

When one of the SMC-50's inputs is configured for Emergency Runand that input is activated, all system faults are disabled. Thisprevents the system from being shut down by a fault.

External Braking Control�

An external braking device can be used to externally brake a motorcontrolled by the SMC-50. The external braking device is activatedusing one of the SMC-50's auxilliary relays configured for “ExtBrake” with the stop mode parameter set to "Ext Brake". The relayis energized when the “Stop” command is given and stays on untilthe time configured in the “Stop Time” parameter counts down tozero.

� Not intended to be used as an emergency stop. Refer to the applicable standards foremergency stop requirements.

‡ Accu-Stop is not included as a parameter/function like that of the SMC-Flex. However,the Accu-Stop function can be accomplished with the Stop Option and Slow Speed withBraking functions.

SCR Control - Normal Run Operation

The SMC-50 uses its power section SCRs to start, run, and stop(except for Coast-to-Stop) a squirrel-cage induction motor. Thebasic operation of the SCRs is to switch on (conduct) for a certainpercentage of the 50/60 Hz AC sine wave, as directed by the SMC-50, to control the amount of voltage applied to the motor. By usingspecial control algorithms and motor feedback to manage voltagesupplied, the SMC-50 provides the previously outlined motorstarting, stopping, and braking control modes. During the normalrun operation, the SMC-50 power section SCRs are conducting for100% of the 50/60 Hz AC sine wave to provide the motor specifiedfull load current (FLA/FLC) voltage and the resulting torque.

Running ModesThe SMC-50 Smart Motor Controller provides the following running modes of operation as standard:

External Bypass – Optional Run Operation

An external bypass contactor can be used to carry the motorrunning current. In this running mode, the SCRs are only used forstarting and potentially stopping depending on the stop modeselected. The SMC-50 controls the external bypass using one of itsauxiliary relay outputs. When the SMC-50 is used in the externalbypass mode with the contacts of the external bypass contactorclosed, the user has the option of using the SMC-50's internal orexternal current sensing capabilities. If using external currentsensing so that metering, alarm/fault, etc. conditions are reported tothe controller during run operation, an external Bulletin 825-MCMConverter Module is required to interface with the 150-SM2 OptionModule. This configuration enables the SMC-50's current-relatedmotor protection features to be used (e.g., external overload notrequired).

NOTE: If this configuration is not used, a means of external motorprotection is required when using an external bypass contactor.

If the bypass kit is used (Frames C and D only), the SMC-50 is usedfor current sensing, metering, alarm/fault conditions, etc. and neithera Bulletin 825-MCM converter module nor a Cat. No. 150-SM2 arerequired.

Bulletin 150




Features

Motor & Starter Protection Features

Motor Protection Features

Excessive Starts Per HourThe SMC-50 permits the user to program the allowed number of starts within a one-hour sliding window (up to 99). This helps eliminatemotor stress caused by repetitive starting during a short time period. An alarm or fault can be enabled using the single configured value.

User-Configurable Alarms & FaultsIn addition to the previous motor alarms and faults, the following can also be configured:

The SMC-50 also has user-configurable motor alarms and faults which can be used to indicate required or planned maintenance.� Planned Maintenance Hours � Planned Maintenance Starts

Stall Protection and Jam DetectionMotors can experience locked-rotor currents and develop high torque levels in the event of a stall or a jam. These conditions can result inwinding insulation breakdown or mechanical damage to the connected load. The SMC-50 provides both stall protection and jam detection forenhanced motor and system protection. A jam level (as a percent of motor FLC) is configurable for both an alarm and motor shutdown (fault).In addition, both stall and jam conditions provide the ability to set a delay time before initiating an alarm (jam only) or motor shutdown (fault).

Underload ProtectionUtilizing the Underload Protection of the SMC-50, an alarm can be sounded or motor operation can be halted (fault) if a drop in current issensed.The SMC-50 provides an adjustable underload trip setting from 0…99% of the programmed motor full-load current rating with an adjustabletrip delay time of 0.1…99.0 seconds.

� Apparent Power � Current Imbalance � Power Quality� � Open Load� � Power Quality THD Current� OverPower � UnderPower � Power Factor Over � Power Factor Under

− Real − Real − Leading − Leading− Reactive Consumed − Reactive Consumed − Lagging − Lagging− Reactive Produced − Reactive Produced

� Contains no parameters to configure.

The SMC-50 provides both motor and starter alarms and faults. An alarm condition is intended to providean alert that a potential system issue, or fault is pending to allow time to take corrective action. A fault isintended to protect equipment from damage by shutting that equipment down and/or removing power. TheSMC-50 provides the ability to individually enable or disable motor and starter alarms and faults by bit(On/Off) selection. Alarm and fault trip points are typically user-configurable to allow for applicationdependence. In addition, many alarms and faults provide a separate user-configurable alarm and fault timedelay parameter to limit nuisance trips and shutdowns.The SMC-50 has a separate Fault Buffer and Alarm Buffer to maintain a Fault/Alarm history. In addition tothe fault/alarm code and description, a time and date stamp is provided by the SMC-50's Real Time Clock(RTC). The Fault Buffer holds the last five faults which provide the time and date; the Alarm Buffer holds thelast 100 alarm events which detail the time, date, parameter change, Start, Stop, Coast, Slow SpeedOperation, Alarm. Fault, and Fault Reset.As standard, the SMC-50 enables manual reset of a fault from the PUSH-TO-RESET/HOLD-TO-TESTbutton, located adjacent to the LED status indicator. Fault indication and reset can also be performed froman optional controller bezel and/or panel-mount HIM or from PC software (e.g., DriveExplorer).

Electronic Motor Overload ProtectionAs standard, the SMC-50 incorporates electronic motor overload protection. This is accomplishedelectronically with an I2t algorithm.Overload Protection is intended to protect the motor, motor controller, and power wiring againstoverheating caused by excessive overcurrent. The SMC-50 meets applicable requirements as a motoroverload protective device. It is not intended, however, to protect against a short circuit condition. The SMC-50’s overload protection is programmable, providing the user maximum flexibility. The OverloadTrip class is either OFF or is configurable from 5 to 30. The overload is programmed by entering the motorfull-load current rating, service factor, and selecting the trip class. Thermal memory is included to accurately model motor operating temperature. Ambient temperatureinsensitivity is inherent in the electronic design of the overload. A user-configurable timer can also be set todisable the overload function during motor starts; another timer provides the ability to monitor the amountof time remaining before the overload trip occurs. Manual or automatic reset of an overload is configurable.

Bulletin 150




Features

� Phase Reversal (CBA Connection) � Parameter Configuration Change � Frequency High and Low� Open SCR Gate � Line Loss with Phase Identification � Poor Voltage Power Quality — THD V

Metering SystemPower and operational monitoring parameters include:

Voltage Unbalance ProtectionVoltage unbalance is detected by monitoring the three-phase supply voltage magnitudes in conjunction with the rotational relationship of thethree phases. The SMC-50 will halt motor operation when the calculated voltage unbalance reaches the user-programmed trip level.The voltage unbalance trip level is programmable from 0…25% unbalance.In addition to the aforementioned faults and alarms, the following are also available:

� Current The RMS current value is provided for each phase, plus the average current of all three.� Voltage The RMS line-to-line and line-to-neutral voltage values are provided while the motor is running and when stopped. The average of

all three is also provided.� Line Frequency The SMC-50 measures and provides user access to the line frequency (Hz).� Power Real, reactive, and apparent power values are calculated for each phase plus the total for all 3 phases. In addition, the current

power demand and the maximum power demand is provided. � Power Factor The value of the power factor is provided for each phase and as a total of all three.� Peak Starting Current The SMC-50 stores the peak average RMS motor current consumed for the last 5 start cycles.� Total Harmonic Distortion (THD) The SMC-50 calculates and provides user access to the THD for the 3 line voltages and 3 motor

currents, along with the average value of each.� Voltage Unbalance The calculation of the voltage unbalance signal is provided. � Current Imbalance The calculation of the current imbalance signal is provided.� Energy Savings The SMC-50 provides the percentage of energy saved when it is running the motor in the Energy Savings mode.� Motor Torque Electromechanical motor torque is calculated based on current and voltage feedback from the motor.� Motor Speed The SMC-50 provides a calculated estimate of motor speed in percent of full speed when operating in the linear speed

acceleration starting or deceleration stopping mode.� Elapsed Time & Elapsed Time 2 An elapsed time meter is provided to account for the total accumulated hours the motor has been

running. The meter can be reset by the user. Elapsed Time 2 cannot be user reset and will hold after 50,000 hours have elapsed.� Running Time The running time meter accumulates time (in hours) from the point the motor start command is given up to the point the

motor stop command is issued. When a new start command is given, the meter resets to zero and begins accumulating time again.� Actual Start Time The unit stores the actual time it takes to complete a start cycle (motor start command issued until motor is up-to-

speed). The last five start times are stored as parameters for user access and in the Alarm Buffer as events.� Total Starts The total starts counter increments on every successful start (no prestart fault occurred) and cannot be reset. The maximum

value is 65,635.

Starter Protection FeaturesUndervoltage ProtectionThe SMC-50's Undervoltage Protection can sound an alarm or halt (fault) motor operation if a drop in the incoming line voltage is detected.The undervoltage trip level is adjustable as a percentage of the programmed line voltage from 0…100%. To eliminate nuisance trips, aprogrammable undervoltage trip delay time of 0.1…99.0 seconds can also be programmed. The line voltage must remain below theundervoltage trip level during the programmed delay time.

Overvoltage ProtectionIf a rise in the incoming line voltage is detected, the SMC-50’s Overvoltage Protection can sound an alarm or halt (fault) motor operation.The overvoltage trip level is adjustable as a percentage of the programmed line voltage, from 100…199%. To eliminate nuisance trips, aprogrammable overvoltage trip delay time of 0.1…99.0 seconds can also be programmed. The line voltage must remain above theovervoltage trip level during the programmed delay time.

Bulletin 150




Features

Communications

8

DPI Port 2(and 3 with Splitter)

DPI Port 4

SMC-50 Control Module(shown without cover)

DPI Port 1

Device Peripheral Interface (DPI) ProtocolThe SMC-50 Soft Motor Starter communicates in the same manner as the Allen-Bradley SMC Flex and drive products using the DPI protocol.This enables almost any DPI-supported Human Interface Module (HIM), PC software (e.g., DriveExplorer), or network communications module(20-COMM-X) to be used with the SMC-50. The SMC-50 supports four DPI ports for communication devices. Port #1 is located in thecontroller bezel for the front-mounted HIM. Port #2, located on the top of the controller, supports a second and third device via Port #3 whena DPI splitter is used. Port #4, located directly below the controller bezel, is dedicated to a 20-COMM-X network communications modulewhen inserted into the space alloted for controller option Port #9. All four communication ports can be used simultaneously.

DeviceLogix™DeviceLogix is an embedded control technology in selected Allen-Bradley porducts that can control outputs and manage status informationon board a device. The SMC-50 with DevceLogix technology can help improve system performance and productivity by controlling outputsand managing status and information within the SMC-50. Speed up reaction time by processing information within the controller, whichreduces dependency on network throughput and provides an option for decision making if communication with the main controller is lost.

Bulletin 150




Features

Controller Parameter Configuration

Parameter Configuration Option Module (Cat. No.150-SM6)

Configuration by Keypad & LCD Display (Human InterfaceModule Cat. No. 20-HIM-A6)

150-SM6 Parameter Configuration Module

SMC-50 Smart Motor Controller with 20-HIM-A6

The SMC-50's starting, stopping, and running operations are configured/programmed by changing the settings of a functionally predefinedset of parameters. Several different configuration tools are available to perform this.NOTE: A configuration tool is not shipped with the starter/controller. The desired configuration tool must be ordered separately.

The upper right portion of the SMC-50 has a dedicated bezel andDPI port for the Cat. No. 20-HIM-A6. The 20-HIM-A6 features anLCD display to show parameter data values, detailed diagnosticalarm/fault information, numeric keypad with function keys to enterparameter data values and navigate to the different SMC-50parameter menus, null parameter configuration and diagnosticdisplay, and the ability to set up SMC-50 Controller Option Modules.Optional extension cables and control cabinet door mounting kitsare available to mount the HIM off the SMC-50.

Configuration by PC Programmable SoftwareConnected Components Workbench (CCW) PC software providesnetwork connectivity between the PC and the SMC-50 as well asconfigurability of the full set of parameters of the SMC-50. Toachieve connectivity, the PC can be directly connected to the SMC-50 DPI Port #2 (or #3 using a splitter) with (1) a 1203-SSSAnaCANda™ RS232 to DPI device or (2) a 1203-USB DPI to USBdevice.

The Parameter Configuration Option Module inserts into any one ofthe SMC-50's three option ports (Port 7, 8 or 9). The 150-SM6features three sets of 8-position ON/OFF DIP switches and five setsof 16-position rotary switches. These switches allow forconfiguration of several key motor parameters (e.g., start and stopmodes, ramp time, motor FLA, etc.) for limited setup of simpleapplications. In addition, the 150-SM6 features three diagnostic LEDstatus indicators to display key alarms and faults. Only one 150-SM6 is allowed per SMC-50.NOTE: After parameter configuration is complete, the 150-SM6 canbe removed from the SMC-50. This enables one module toconfigure multiple SMC-50s.

When using a Cat. No. 150-SM6 PCM to configure the SMC-50, itshould be noted that the following features, functions, and modesare not configurable:

� Full voltage start

� Torque ramp start

� External brake stop

� Option card I/O configuration (Cat. No. 150-SM… optionmodules)

� External bypass

� Specialized output relay configuration (e.g., network control,DeviceLogix, auxiliary control)

� Specialized operation modes/features

� Dual ramp, motor winding heater, emergency run

� Overload select (Class)

� Adjustment of slow speed set point

Parameters that are not defined and therefore are not configurableby the Cat. No. 150-SM6 PCM can be configured through othermeans (e.g., Human Interface Module (HIM), ConnectedComponents Workbench (CCW), DriveExplorer or DriveExecutivesoftware), if necessary.

Bulletin 150




Features

150-SM2 Option Module

Control Inputs & Outputs

SMC-50 Smart Motor Controller with 150-SM4

� All standard and optional I/O Terminal Blocks are removable

‡ The ground fault sensing feature of the SMC-50 is intended for monitoring purposes only.

It is not to be used as a ground fault circuit interrupter for personnel protection as defined

by Article 100 of the NEC. The sensing feature has not been evaluated to UL 1053.

Standard Inputs�

The SMC-50 comes standard with two 24V DC inputs. The controlfunctionality of each input is user-configurable as follows: Start,Coast, Stop Option (e.g., Soft Stop, Pump Stop), Start/Coast,Start/Stop, Slow Speed, Overload Select, Fault Input (N.O.), FaultInput (N.C.), Clear Fault, Emergency Run, Dual Ramp Profile Select,and Start Motor Heater function. The status of any input is readablevia communications.

Optional Inputs�

A Cat. No. 150-SM4 Digital I/O option module contains four120/240V AC inputs and can be inserted into any of the threecontrol module option ports (three modules maximum per controlmodule). The control functionality of each input is user configurableand identical to the standard inputs. The status of any input isreadable via communications.

A Cat. No. 150-SM3 Analog I/O option module provides two analoginputs (voltage or current) and can be inserted into any of the threecontrol module option ports (three modules maximum per controlmodule). The control functionality of each input is user configurable.The status of any input is readable via communications.

Optional PTC, Ground Fault‡, & Current Transformer InterfaceCapability�

The Cat. No. 150-SM2 Option Module features PTC, ground fault,and external current transformer interface capability. The PTCfeature enables connection to external PTC temperature sensors tomonitor motor winding temperature and feedback data to the SMC-50. A SMC-50 Alarm and/or Fault can be configured to trip if thePTC setpoint is exceeded. The ground fault feature enablescontroller detection and enunciation of a possible system groundfault which could indicate a pending motor winding failure (e.g.,insulation breakdown). A Bulletin 825-CBCT External Ground Fault(Core Balance) Sensor is also required to interface with the 150-SM2 to fully enable this feature. When the SMC-50 is used in the external bypass mode with thecontacts of the external bypass contactor closed, the user has theoption of using the SMC-50's internal or external current sensingcapabilities. If using external current sensing so that metering,alarm/fault, etc. conditions are reported to the controller during runoperation, an external Bulletin 825-MCM Converter Module isrequired to interface with the 150-SM2 Option Module.

Standard and Optional Outputs�

The SMC-50 comes standard with two relay outputs. By adding aCat. No. 150-SM4 Digital I/O Option Module, three additional relayoutputs are provided (three option modules maximum per controlmodule). The control functionality of each relay output is user-configurable as follows: Normal (Start Enabled), Up-To-Speed, Fault,Alarm, External Bypass, External brake, Auxillary Control, andNetwork 1-4. Each output also includes a user-configurable on andoff delay timer (10.0 seconds maximum) and the ability to invert thestate of the contact. Network control of each output is alsoprovided.

By adding a Cat. No. 150-SM3 Analog I/O module, two analogoutputs (voltage of current) are provided.

Bulletin 150




Catalog Number Explanation

Open and Non-Combination Enclosed Controllers

aBulletin Number — Product Type

Code Description

150-S SMC-50 Solid-State Motor Controller

150B-S Solid-State Motor Controller withIsolation Contactor

bController Ratings

Code Description

B1 90 A

B2 110 A

B3 140 A

B4 180 A

C1 210 A

C2 260 A

C3 320 A

D1 361 A

D2 420 A

D3 520 A

cEnclosure Type

Code Description

F NEMA Type 4/12 (IP65)

N Open

dLine Voltage

Open Type

Code Description

B 200…460V AC, 3-phase, 50 and 60 Hz

U 200…690V AC, 3-phase, 50 and 60 Hz

Non-Combination Enclosed Only

Code Description

H 200…208V AC, 3-phase, 50 and 60 Hz

A 230V AC, 3-phase, 50 and 60 Hz

B 400…460V AC, 3-phase, 50 and 60 Hz

C 500…575V AC, 3-phase, 50 and 60 Hz

eControl Voltage

Code Description

D 100…240V AC (two 24V DC inputs andtwo relay outputs standard)

R 24V DC (two 24V DC inputs and two relayoutputs standard)

150-S B1 N U D - 8Ba b c d e f

Combination Enclosed Controllers

152H-S B1 F BD - 41 - 8Ba b c d e f

aBulletin Number — Product Type

Code Description

152H-S Solid-State Controller with FusibleDisconnect

152B-S Solid-State Controller with FusibleDisconnect and Isolation Contactor

153H-S Solid-State Controller with CircuitBreaker

153B-S Solid-State Controller with CircuitBreaker and Isolation Contactor

bController Ratings

Code Description

B1 90 A, 60 Hp @ 460V AC

B2 110 A, 75 Hp @ 460V AC

B3 140 A, 100 Hp @ 460V AC

B4 180 A, 150 Hp @ 460V AC

C1 210 A, 150 Hp @ 460V AC

C2 260 A, 200 Hp @ 460V AC

C3 320 A, 250 Hp @ 460V AC

D1 361 A, 300 Hp @ 460V AC

D2 420 A, 400 Hp @ 460V AC

D3 520 A, 450 Hp @ 460V AC

cEnclosure Type

Code Description

F NEMA Type 4/12 (IP65)

J NEMA Type 12 (IP54)

dLine Voltage

Code Description

HD 200…208V AC, 3-phase, 50 and 60 Hz

AD 230V AC, 3-phase, 50 and 60 Hz

BD 400…460V AC, 3-phase, 50 and 60 Hz

CD 500…575V AC, 3-phase, 50 and 60 Hz

eHorsepower

Code Hp Rating

41 10

42 15

43 20

44 25

45 30

46 40

47 50

48 60

49 75

50 100

51 125

52 150

54 200

56 250

57 300

58 350

59 400

60 450

61 500

fOptions - See page 29 for a full list of available

options

Code Description

8L Line-Mounted Protective Module

8M Load-Mounted Protective Module

8B Line- and Load-Mounted ProtectiveModules

Load-side MOVs are not available with pump,braking, linear acceration, or linear decelerationstarting and stopping modes. Load-side MOVsshould also not be used with inside-the-delta-connected motor configurations. MOVs can befield installed for open type units.

fOptions - Non-combination enclosed only; see

page 29 for a full list of available options

Code Description

8L Line-Mounted Protective Module

8M Load-Mounted Protective Module

8B Line- and Load-Mounted ProtectiveModules

Load-side MOVs are not available with pump,braking, and linear acceration or decelerationstarting and stopping modes. They should alsonot be used with inside-the-delta-connectedmotor configurations. MOVs can be field installedfor open type units.

Bulletin 150




Product Selection

RatedUtilization

Voltage[V AC]

Motor Current[A]

Motor kW, 50 Hz

Motor Hp, 60 Hz Control Power Cat. No.

IP65 (Type 4/12) Enclosed Non-Combination Controllers

Cat. No.

230

30…90 10…25 15…30100…240V AC; 50/60 Hz 150-SB1NBD 150-SB1FAD

24V DC 150-SB1NBR —

37…110 11…32 15…40100…240V AC; 50/60 Hz 150-SB2NBD § 150-SB2FAD




60…180 18.5…55 25…60100…240V AC; 50/60 Hz 150-SB4NBD § 150-SB4FAD


70…210 22…63 30…75100…240V AC; 50/60 Hz 150-SC1NBD § 150-SC1FAD

24V DC 150-SC1NBR —





120…361 40…110 50…150100…240V AC; 50/60 Hz 150-SD1NBD § 150-SD1FAD

24V DC 150-SD1NBR —





§ Requires a bypass contactor. Add -BP or -NB to the end of the catalog number to denote an IEC or NEMA bypass contactor, respectively. Example, for aNEMA bypass contactor, Cat. No. 150-SB2FAD becomes 150-SB2FAD-NB.

RatedUtilization

Voltage[V AC]

Motor Current[A]

Motor kW, 50 Hz



Cat. No.

200/208

30…90

⎯

10…25100…240V AC; 50/60 Hz 150-SB1NBD 150-SB1FHD


37…110 15…30100…240V AC; 50/60 Hz 150-SB2NBD § 150-SB2FHD






70…210 25…60100…240V AC; 50/60 Hz 150-SC1NBD § 150-SC1FHD






120…361 50…125100…240V AC; 50/60 Hz 150-SD1NBD § 150-SD1FHD






§ Requires a bypass contactor. Add -BP or -NB to the end of the catalog number to denote an IEC or NEMA bypass contactor, respectively. Example, for aNEMA bypass contactor, Cat. No. 150-SB2FHD becomes 150-SB2FHD-NB.

Normal/Standard Duty Ratings (for pumps, compressors, elevators, and short conveyors)Utilization Category: AC-53a:3.5-10:99-2. Start Not to Exceed: 350% of the controller maximum current rating, 10 second start time, 99%ON load factor, two starts per hour with 40 °C surrounding air ambient temperature.NOTE: Refer to and use Selection Wizards to ensure the SMC selection meets the application requirements. For additional assistance, pleasevisit www.ab.com or contact Industrial Controls Technical Support by email at [email protected] or by phone at 440-646-5800.

Normal Duty Rated Open Type and Non-Combination Enclosed Controllers ⎯ For Use with Line-Connected Motors

Bulletin 150




Product Selection

RatedUtilization

Voltage[V AC]

Motor Current[A]

Motor kW, 50 Hz



Cat. No.

400/415 (kW)460 (Hp)

30…90 17…50 25…60100…240V AC; 50/60 Hz 150-SB1NBD 150-SB1FBD


37…110 20…55 30…75100…240V AC; 50/60 Hz 150-SB2NBD § 150-SB2FBD






70…210 40…110 60…150100…240V AC; 50/60 Hz 150-SC1NBD § 150-SC1FBD






120…361 75…200 100…300100…240V AC; 50/60 Hz 150-SD1NBD § 150-SD1FBD






§ Requires a bypass contactor. Add -BP or -NB to the end of the catalog number to denote an IEC or NEMA bypass contactor, respectively. Example, for aNEMA bypass contactor, Cat. No. 150-SB2FBD becomes 150-SB2FBD-NB.

RatedUtilization

Voltage[V AC]

Motor Current[A]

Motor kW, 50 Hz



Cat. No.

500 (kW)575 (Hp)

30…90 20…63 30…75100…240V AC; 50/60 Hz 150-SB1NUD 150-SB1FCD

24V DC 150-SB1NUR —

37…110 25…75 40…100100…240V AC; 50/60 Hz 150-SB2NUD § 150-SB2FCD






70…210 50…150 75…200100…240V AC; 50/60 Hz 150-SC1NUD § 150-SC1FCD

24V DC 150-SC1NUR —





120…361 90…250 125…350100…240V AC; 50/60 Hz 150-SD1NUD § 150-SD1FCD

24V DC 150-SD1NUR —





§ Requires a bypass contactor. Add -BP or -NB to the end of the catalog number to denote an IEC or NEMA bypass contactor, respectively. Example, for aNEMA bypass contactor, Cat. No. 150-SB2FCD becomes 150-SB2FCD-NB.

Normal Duty Rated Open Type and Non-Combination Enclosed Controllers ⎯ For Use with Line-Connected Motors

Bulletin 150




Product Selection

Rated UtilizationVoltage[V AC] Motor Current [A] Motor kW, 50 Hz Motor Hp, 60 Hz Control Power Cat. No.

690/Y (kW) 600 (Hp)

30…90 30…80 30…75100…240V AC; 50/60 Hz 150-SB1NUD

24V DC 150-SB1NUR

37…110 37…100 40…100100…240V AC; 50/60 Hz 150-SB2NUD

24V DC 150-SB2NUR

47…140 45…132 50…125100…240V AC; 50/60 Hz 150-SB3NUD

24V DC 150-SB3NUR

60…180 63…160 60…150100…240V AC; 50/60 Hz 150-SB4NUD

24V DC 150-SB4NUR

70…210 75…200 75…200100…240V AC; 50/60 Hz 150-SC1NUD

24V DC 150-SC1NUR

87…260 90…250 100…250100…240V AC; 50/60 Hz 150-SC2NUD

24V DC 150-SC2NUR

107…320 110…315 125…300100…240V AC; 50/60 Hz 150-SC3NUD

24V DC 150-SC3NUR

120…361 125…355 125…350100…240V AC; 50/60 Hz 150-SD1NUD

24V DC 150-SD1NUR

140…420 160…400 150…450100…240V AC; 50/60 Hz 150-SD2NUD

24V DC 150-SD2NUR

174…520 185…500 200…500100…240V AC; 50/60 Hz 150-SD3NUD

24V DC 150-SD3NUR

Normal Duty Rated Open Type Controllers ⎯ For Use with Line-Connected Motors

Bulletin 150




Product Selection

RatedUtilization

Voltage[V AC]

Motor Current[A]

Motor kW, 50 Hz



Cat. No.

200/208

30…90

⎯

10…25100…240V AC; 50/60 Hz 150-SB2NBD § 150-SB2FHD


















§ Requires a bypass contactor. Add -BP or -NB to the end of the catalog number to denote an IEC or NEMA bypass contactor, respectively. Example, for aNEMA bypass contactor, Cat. No. 150-SB2FHD becomes 150-SB2FHD-NB.

RatedUtilization

Voltage[V AC]

Motor Current[A]

Motor kW, 50 Hz



Cat. No.

230







60…180 18.5…55 25…60100…240V AC; 50/60 Hz 150-SC1NBD § 150-SC1FAD












§ Requires a bypass contactor. Add -BP or -NB to the end of the catalog number to denote an IEC or NEMA bypass contactor, respectively. Example, for aNEMA bypass contactor, Cat. No. 150-SB2FAD becomes 150-SB2FAD-NB.

Heavy Duty Ratings (for centrifugal fans, crushers, mixers, long conveyors, etc.)Utilization Category: AC-53a:3.5-30:99-1. Start Not to Exceed: 350% of the controller maximum current rating, 30 second start time, 99%ON load factor, one start per hour with 50 °C surrounding air ambient temperature.NOTE: Refer to and use Selection Wizards to ensure the SMC selection meets the application requirements. For additional assistance, pleasevisit www.ab.com or contact Industrial Controls Technical Support by email at [email protected] or byphone at 440-646-5800.

Heavy Duty Rated Open Type and Non-Combination Enclosed Controllers ⎯ For Use with Line-Connected Motors

Bulletin 150




Product Selection

RatedUtilization

Voltage[V AC]

Motor Current[A]

Motor kW, 50 Hz



Cat. No.

400/415 (kW)460 (Hp)



















§ Requires a bypass contactor. Add -BP or -NB to the end of the catalog number to denote an IEC or NEMA bypass contactor, respectively. Example, for aNEMA bypass contactor, Cat. No. 150-SB2FBD becomes 150-SB2FBD-NB.

RatedUtilization

Voltage[V AC]

Motor Current[A]

Motor kW, 50 Hz



Cat. No.

500 (kW)575 (Hp)



















§ Requires a bypass contactor. Add -BP or -NB to the end of the catalog number to denote an IEC or NEMA bypass contactor, respectively. Example, for aNEMA bypass contactor, Cat. No. 150-SB2FCD becomes 150-SB2FCD-NB.

Heavy Duty Rated Open Type and Non-Combination Enclosed Controllers ⎯ For Use with Line-Connected Motors

Bulletin 150




Product Selection


690/Y (kW) 600 (Hp)

30…90 30…80 30…75100…240V AC; 50/60 Hz 150-SB2NUD

24V DC 150-SB2NUR

37…110 37…100 40…100100…240V AC; 50/60 Hz 150-SB3NUD

24V DC 150-SB3NUR

47…140 45…132 50…125100…240V AC; 50/60 Hz 150-SB4NUD

24V DC 150-SB4NUR

60…180 63…160 60…150100…240V AC; 50/60 Hz 150-SC1NUD

24V DC 150-SC1NUR

70…210 75…200 75…200100…240V AC; 50/60 Hz 150-SC2NUD

24V DC 150-SC2NUR

87…260 90…250 100…250100…240V AC; 50/60 Hz 150-SC3NUD

24V DC 150-SC3NUR

107…320 110…315 125…300100…240V AC; 50/60 Hz 150-SD1NUD

24V DC 150-SD1NUR

120…361 125…355 125…350100…240V AC; 50/60 Hz 150-SD2NUD

24V DC 150-SD2NUR

140…420 160…400 150…450100…240V AC; 50/60 Hz 150-SD3NUD

24V DC 150-SD3NUR

Heavy Duty Rated Open Type Controllers ⎯ For Use with Line-Connected Motors

Bulletin 150




Product Selection


200/208

52…155

—

20…50100…240V AC; 50/60 Hz 150-SB1NBD

24V DC 150-SB1NBR

65…190 25…60100…240V AC; 50/60 Hz 150-SB2NBD

24V DC 150-SB2NBR

82…242 30…75100…240V AC; 50/60 Hz 150-SB3NBD

24V DC 150-SB3NBR

104…311 40…100100…240V AC; 50/60 Hz 150-SB4NBD

24V DC 150-SB4NBR

122…363 50…125100…240V AC; 50/60 Hz 150-SC1NBD

24V DC 150-SC1NBR

151…450 60…150100…240V AC; 50/60 Hz 150-SC2NBD

24V DC 150-SC2NBR

186…554 75…200100…240V AC; 50/60 Hz 150-SC3NBD

24V DC 150-SC3NBR

210…625 75…200100…240V AC; 50/60 Hz 150-SD1NBD

24V DC 150-SD1NBR

243…727 100…250100…240V AC; 50/60 Hz 150-SD2NBD

24V DC 150-SD2NBR

302…900 125…300100…240V AC; 50/60 Hz 150-SD3NBD

24V DC 150-SD3NBR


230

52…155 17…50 20…60100…240V AC; 50/60 Hz 150-SB1NBD

24V DC 150-SB1NBR

65…190 20…55 25…60100…240V AC; 50/60 Hz 150-SB2NBD

24V DC 150-SB2NBR

82…242 30…75 40…75100…240V AC; 50/60 Hz 150-SB3NBD

24V DC 150-SB3NBR

104…311 37…100 40…100100…240V AC; 50/60 Hz 150-SB4NBD

24V DC 150-SB4NBR

122…363 40…110 50…125100…240V AC; 50/60 Hz 150-SC1NBD

24V DC 150-SC1NBR

151…450 50…132 60…150100…240V AC; 50/60 Hz 150-SC2NBD

24V DC 150-SC2NBR

186…554 63…160 75…200100…240V AC; 50/60 Hz 150-SC3NBD

24V DC 150-SC3NBR

210…625 75…200 100…250100…240V AC; 50/60 Hz 150-SD1NBD

24V DC 150-SD1NBR

243…727 80…220 100…300100…240V AC; 50/60 Hz 150-SD2NBD

24V DC 150-SD2NBR

302…900 100…300 125…350100…240V AC; 50/60 Hz 150-SD3NBD

24V DC 150-SD3NBR

Normal Duty Rated Open Type Controllers ⎯ For Use with Delta-Connected Motors

Normal/Standard Duty Ratings (for pumps, compressors, elevators, and short conveyors)Utilization Category: AC-53a:3.5-10:99-2. Start Not to Exceed: 350% of the controller maximum current rating, 10 second start time, 99%ON load factor, two starts per hour with 40 °C surrounding air ambient temperature.NOTE: Refer to and use Selection Wizards to ensure the SMC selection meets the application requirements. For additional assistance, pleasevisit www.ab.com or contact Industrial Controls Technical Support by email at [email protected] or by phone at 440-646-5800.

Bulletin 150




Product Selection

Rated UtililizationVoltage[V AC] Motor Current [A] Motor kW, 50 Hz Motor Hp, 60 Hz Control Power Cat. No.

400/415 (kW)460 (Hp)

52…155 30…80 40…100100…240V AC; 50/60 Hz 150-SB1NBD

24V DC 150-SB1NBR

65…190 37…100 50…150100…240V AC; 50/60 Hz 150-SB2NBD

24V DC 150-SB2NBR

82…242 50…132 75…200100…240V AC; 50/60 Hz 150-SB3NBD

24V DC 150-SB3NBR

104…311 63…160 100…250100…240V AC; 50/60 Hz 150-SB4NBD

24V DC 150-SB4NBR

122…363 75…200 100…300100…240V AC; 50/60 Hz 150-SC1NBD

24V DC 150-SC1NBR

151…450 90…250 125…350100…240V AC; 50/60 Hz 150-SC2NBD

24V DC 150-SC2NBR

186…554 110…315 200…450100…240V AC; 50/60 Hz 150-SC3NBD

24V DC 150-SC3NBR

210…625 125…355 200…500100…240V AC; 50/60 Hz 150-SD1NBD

24V DC 150-SD1NBR

243…727 150…400 250…600100…240V AC; 50/60 Hz 150-SD2NBD

24V DC 150-SD2NBR

302…900 185…530 250…700100…240V AC; 50/60 Hz 150-SD3NBD

24V DC 150-SD3NBR


500 (kW)575 (Hp)

52…155 37…100 50…150100…240V AC; 50/60 Hz 150-SB1NUD

24V DC 150-SB1NUR

65…190 50…132 75…150100…240V AC; 50/60 Hz 150-SB2NUD

24V DC 150-SB2NUR

82…242 63…160 100…250100…240V AC; 50/60 Hz 150-SB3NUD

24V DC 150-SB3NUR

104…311 75…220 125…300100…240V AC; 50/60 Hz 150-SB4NUD

24V DC 150-SB4NUR

122…363 90…250 125…350100…240V AC; 50/60 Hz 150-SC1NUD

24V DC 150-SC1NUR

151…450 110…315 200…450100…240V AC; 50/60 Hz 150-SC2NUD

24V DC 150-SC2NUR

186…554 132…400 200…500100…240V AC; 50/60 Hz 150-SC3NUD

24V DC 150-SC3NUR

210…625 150…450 250…600100…240V AC; 50/60 Hz 150-SD1NUD

24V DC 150-SD1NUR

243…727 185…530 300…700100…240V AC; 50/60 Hz 150-SD2NUD

24V DC 150-SD2NUR

302…900 220…670 350…900100…240V AC; 50/60 Hz 150-SD3NUD

24V DC 150-SD3NUR

Normal Duty Rated Open Type Controllers ⎯ For Use with Delta-Connected Motors

Bulletin 150




Product Selection

Heavy Duty Rated Open Type Controllers ⎯ For Use with Delta-Connected Motors


200/208

52…155

—

20…50100…240V AC; 50/60 Hz 150-SB2NBD

24V DC 150-SB2NBR

65…190 25…60100…240V AC; 50/60 Hz 150-SB3NBD

24V DC 150-SB3NBR

82…242 30…75100…240V AC; 50/60 Hz 150-SB4NBD

24V DC 150-SB4NBR

104…311 40…100100…240V AC; 50/60 Hz 150-SC1NBD

24V DC 150-SC1NBR

122…363 50…125100…240V AC; 50/60 Hz 150-SC2NBD

24V DC 150-SC2NBR

151…450 60…150100…240V AC; 50/60 Hz 150-SC3NBD

24V DC 150-SC3NBR

186…554 75…200100…240V AC; 50/60 Hz 150-SD1NBD

24V DC 150-SD1NBR

210…625 75…200100…240V AC; 50/60 Hz 150-SD2NBD

24V DC 150-SD2NBR

243…727 100…250100…240V AC; 50/60 Hz 150-SD3NBD

24V DC 150-SD3NBR


230

52…155 17…50 20…60100…240V AC; 50/60 Hz 150-SB2NBD

24V DC 150-SB2NBR

65…190 20…55 25…60100…240V AC; 50/60 Hz 150-SB3NBD

24V DC 150-SB3NBR

82…242 30…75 40…75100…240V AC; 50/60 Hz 150-SB4NBD

24V DC 150-SB4NBR

104…311 37…100 40…100100…240V AC; 50/60 Hz 150-SC1NBD

24V DC 150-SC1NBR

122…363 40…110 50…125100…240V AC; 50/60 Hz 150-SC2NBD

24V DC 150-SC2NBR

151…450 50…132 60…150100…240V AC; 50/60 Hz 150-SC3NBD

24V DC 150-SC3NBR

186…554 63…160 75…200100…240V AC; 50/60 Hz 150-SD1NBD

24V DC 150-SD1NBR

210…625 75…200 100…250100…240V AC; 50/60 Hz 150-SD2NBD

24V DC 150-SD2NBR

243…727 80…220 100…300100…240V AC; 50/60 Hz 150-SD3NBD

24V DC 150-SD3NBR

Heavy Duty Ratings (for centrifugal fans, crushers, mixers, long conveyors, etc.)Utilization Category: AC-53a:3.5-30:99-1. Start Not to Exceed: 350% of the controller maximum current rating, 30 second start time, 99%ON load factor, one start per hour with 50 °C surrounding air ambient temperature.NOTE: Refer to and use Selection Wizards to ensure the SMC selection meets the application requirements. For additional assistance,please visit www.ab.com or contact Industrial Controls Technical Support by email at [email protected] or by phone at 440-646-5800.

Bulletin 150




Product Selection

Rated UtililizationVoltage[V AC] Motor Current [A] Motor kW, 50 Hz Motor Hp, 60 Hz Control Power Cat. No.

400/415 (kW)460 (Hp)

52…155 30…80 40…100100…240V AC; 50/60 Hz 150-SB2NBD

24V DC 150-SB2NBR

65…190 37…100 50…150100…240V AC; 50/60 Hz 150-SB3NBD

24V DC 150-SB3NBR

82…242 50…132 75…200100…240V AC; 50/60 Hz 150-SB4NBD

24V DC 150-SB4NBR

104…311 63…160 100…250100…240V AC; 50/60 Hz 150-SC1NBD

24V DC 150-SC1NBR

122…363 75…200 100…300100…240V AC; 50/60 Hz 150-SC2NBD

24V DC 150-SC2NBR

151…450 90…250 125…350100…240V AC; 50/60 Hz 150-SC3NBD

24V DC 150-SC3NBR

186…554 110…315 200…450100…240V AC; 50/60 Hz 150-SD1NBD

24V DC 150-SD1NBR

210…625 125…355 200…500100…240V AC; 50/60 Hz 150-SD2NBD

24V DC 150-SD2NBR

243…727 150…400 250…600100…240V AC; 50/60 Hz 150-SD3NBD

24V DC 150-SD3NBR


500 (kW)575 (Hp)

52…155 37…100 50…150100…240V AC; 50/60 Hz 150-SB2NUD

24V DC 150-SB2NUR

65…190 50…132 75…150100…240V AC; 50/60 Hz 150-SB3NUD

24V DC 150-SB3NUR

82…242 63…160 100…250100…240V AC; 50/60 Hz 150-SB4NUD

24V DC 150-SB4NUR

104…311 75…220 125…300100…240V AC; 50/60 Hz 150-SC1NUD

24V DC 150-SC1NUR

122…363 90…250 125…350100…240V AC; 50/60 Hz 150-SC2NUD

24V DC 150-SC2NUR

151…450 110…315 200…450100…240V AC; 50/60 Hz 150-SC3NUD

24V DC 150-SC3NUR

186…554 132…400 200…500100…240V AC; 50/60 Hz 150-SD1NUD

24V DC 150-SD1NUR

210…625 150…450 250…600100…240V AC; 50/60 Hz 150-SD2NUD

24V DC 150-SD2NUR

243…727 185…530 300…700100…240V AC; 50/60 Hz 150-SD3NUD

24V DC 150-SD3NUR

Heavy Duty Rated Open Type Controllers ⎯ For Use with Delta-Connected Motors

Bulletin 150




Product Selection

Rated Voltage[V AC] Max. kW, 50 Hz Max. Hp, 60 Hz

Controller CurrentRating [A]

IP65 (Type 4/12) EnclosedCombination Controllerswith Fusible Disconnect

IP65 (Type 4/12) EnclosedCombination Controllers

with Circuit Breaker�Cat. No. Cat. No.

200/208

— 10 90 152H-SB1FHD-41 153H-SB1FHD-41

— 15 90 152H-SB1FHD-42 153H-SB1FHD-42

— 20 90 152H-SB1FHD-43 153H-SB1FHD-43

— 25 90 152H-SB1FHD-44 153H-SB1FHD-44

— 30 110 § 152H-SB2FHD-45 § 153H-SB2FHD-45

— 40 140 § 152H-SB3FHD-46 § 153H-SB3FHD-46

— 50 180 § 152H-SB4FHD-47 § 153H-SB4FHD-47

— 60 180 § 152H-SB4FHD-48 § 153H-SC1FHD-48

— 60 210 § 152H-SC1FHD-48 § 153H-SC1FHD-48

— 75 260 § 152H-SC2FHD-49 § 153H-SC2FHD-49

— 100 320 § 152H-SC3FHD-50 § 153H-SC3FHD-50

— 125 361 § 152H-SD1JHD-51 § 153H-SD1JHD-51

— 150 420 § 152H-SD2JHD-52 § 153H-SD2JHD-52

— 150 520 § 152H-SD3JHD-52 § 153H-SD3JHD-52

230

— 15 90 152H-SB1FAD-42 153H-SB1FAD-42

— 20 90 152H-SB1FAD-43 153H-SB1FAD-43

— 25 90 152H-SB1FAD-44 153H-SB1FAD-44

— 30 90 152H-SB1FAD-45 153H-SB1FAD-45

— 40 110 § 152H-SB2FAD-46 § 153H-SB2FAD-46

— 50 140 § 152H-SB3FAD-47 § 153H-SB3FAD-47

— 60 180 § 152H-SB4FAD-48 § 153H-SB4FAD-48

— 75 210 § 152H-SC1FAD-49 § 153H-SC1FAD-49

— 100 260 § 152H-SC2FAD-50 § 153H-SC2FAD-50

— 125 320 § 152H-SC3FAD-51 § 153H-SC3FAD-51

— 150 361 § 152H-SD1JAD-52 § 153H-SD1JAD-52

— 150 420 § 152H-SD2JAD-52 § 153H-SD2JAD-52

— 200 520 § 152H-SD3JAD-54 § 153H-SD3JAD-54

�These controllers require a separate 100…240V, 50/60 Hz single-phase control source. To add a control circuit transformer to the enclosure, add theappropriate option code to the catalog string.

§ Requires a bypass contactor. Add -BP or -NB to the end of the catalog number to denote an IEC or NEMA bypass contactor, respectively. Example, for aNEMA bypass contactor, Cat. No. 152H-SB2FHD-45 becomes 152H-SB2FHD-45-NB.

Normal Duty Rated Combination Enclosed (IP65, Type 4/12) Controllers with Fusible Disconnect or Circuit Breaker

Bulletin 150




Product Selection





with Circuit BreakerCat. No. Cat. No.

460

— 25 90 152H-SB1FBD-44 153H-SB1FBD-44

— 30 90 152H-SB1FBD-45 153H-SB1FBD-45

— 40 90 152H-SB1FBD-46 153H-SB1FBD-46

— 50 90 152H-SB1FBD-47 153H-SB1FBD-47

— 60 90 152H-SB1FBD-48 153H-SB1FBD-48

— 75 110 § 152H-SB2FBD-49 § 153H-SB2FBD-49

— 100 140 § 152H-SB3FBD-50 § 153H-SB3FBD-50

— 125 180 § 152H-SB4FBD-51 § 153H-SB4FBD-51

— 150 180 § 152H-SB4FBD-52 § 153H-SB4FBD-52

— 150 210 § 152H-SC1FBD-52 § 153H-SC1FBD-52

— 200 260 § 152H-SC2FBD-54 § 153H-SC2FBD-54

— 250 320 § 152H-SC3FBD-56 § 153H-SC3FBD-56

— 300 361 § 152H-SD1JBD-57 § 153H-SD1JBD-57

— 350 420 § 152H-SD2JBD-58 § 153H-SD2JBD-58

— 400 520 § 152H-SD3JBD-59 § 153H-SD3JBD-59

— 450 520 § 152H-SD3JBD-60 § 153H-SD3JBD-60

500/575

— 30 90 152H-SB1FCD-45 153H-SB1FCD-45

— 40 90 152H-SB1FCD-46 153H-SB1FCD-46

— 50 90 152H-SB1FCD-47 153H-SB1FCD-47

— 60 90 152H-SB1FCD-48 153H-SB1FCD-48

— 75 90 152H-SB1FCD-49 153H-SB1FCD-49

— 100 110 § 152H-SB2FCD-50 § 153H-SB2FCD-50

— 125 140 § 152H-SB3FCD-51 § 153H-SB3FCD-51

— 150 180 § 152H-SB4FCD-52 § 153H-SB4FCD-52

— 200 210 § 152H-SC1FCD-54 § 153H-SC1FCD-54

— 250 260 § 152H-SC2FCD-56 § 153H-SC2FCD-56

— 300 320 § 152H-SC3FCD-57 § 153H-SC3FCD-57

— 350 361 § 152H-SD1JCD-58 § 153H-SD1JCD-58

— 400 420 § 152H-SD2JCD-59 § 153H-SD2JCD-59

— 450 520 § 152H-SD3JCD-60 § 153H-SD3JCD-60

— 500 520 § 152H-SD3JCD-61 § 153H-SD3JCD-61

§ Requires a bypass contactor. Add -BP or -NB to the end of the catalog number to denote an IEC or NEMA bypass contactor, respectively. Example, for aNEMA bypass contactor, Cat. No. 152H-SB2FBD-49 becomes 152H-SB2FBD-49-NB.

Normal Duty Rated Combination Enclosed (IP65, Type 4/12) Controllers with Fusible Disconnect or Circuit Breaker

Bulletin 150




Product Selection

Heavy Duty Rated Combination Enclosed (IP65, Type 4/12) Controllers with Fusible Disconnect or Circuit Breaker





with Circuit BreakerCat. No.§ Cat. No.§

200/208

— 10 90 152H-SB2FHD-41 153H-SB2FHD-41

— 15 90 152H-SB2FHD-42 153H-SB2FHD-42

— 20 90 152H-SB2FHD-43 153H-SB2FHD-43

— 25 90 152H-SB2FHD-44 153H-SB2FHD-44

— 30 110 152H-SB3FHD-45 153H-SB3FHD-45

— 40 140 152H-SB4FHD-46 153H-SB4FHD-46

— 50 180 152H-SC1FHD-47 153H-SC1FHD-47

— 60 180 152H-SC1FHD-48 153H-SC1FHD-48

— 60 210 152H-SC2FHD-49 153H-SC2FHD-49

— 75 260 152H-SC3FHD-49 153H-SC3FHD-49

— 100 320 152H-SD1JHD-50 153H-SD1JHD-50

— 125 361 152H-SD2JHD-51 153H-SD2JHD-51

— 150 420 152H-SD3JHD-52 153H-SD3JHD-52

230

— 15 90 152H-SB2FAD-42 153H-SB2FAD-42

— 20 90 152H-SB2FAD-43 153H-SB2FAD-43

— 25 90 152H-SB2FAD-44 153H-SB2FAD-44

— 30 90 152H-SB2FAD-45 153H-SB2FAD-45

— 40 110 152H-SB3FAD-46 153H-SB3FAD-46

— 50 140 152H-SB4FAD-47 153H-SB4FAD-47

— 60 180 152H-SC1FAD-48 153H-SC1FAD-48

— 75 210 152H-SC2FAD-49 153H-SC2FAD-49

— 100 260 152H-SC3FAD-50 153H-SC3FAD-50

— 125 320 152H-SD1JAD-51 153H-SD1JAD-51

— 150 361 152H-SD2JAD-52 153H-SD2JAD-52

— 150 420 152H-SD3JAD-52 153H-SD3JAD-52

§ Requires a bypass contactor. Add -BP or -NB to the end of the catalog number to denote an IEC or NEMA bypass contactor, respectively. Example, for aNEMA bypass contactor, Cat. No. 152H-SB2FHD-41 becomes 152H-SB2FHD-41-NB.

Bulletin 150




Product Selection

Heavy Duty Rated Combination Enclosed (IP65, Type 4/12) Controllers with Fusible Disconnect or Circuit Breaker





with Circuit BreakerCat. No.§ Cat. No.§

460

— 25 90 152H-SB2FBD-44 153H-SB2FBD-44

— 30 90 152H-SB2FBD-45 153H-SB2FBD-45

— 40 90 152H-SB2FBD-46 153H-SB2FBD-46

— 50 90 152H-SB2FBD-47 153H-SB2FBD-47

— 60 90 152H-SB2FBD-48 153H-SB2FBD-48

— 75 110 152H-SB3FBD-49 153H-SB3FBD-49

— 100 140 152H-SB4FBD-50 153H-SB4FBD-50

— 125 180 152H-SC1FBD-51 153H-SC1FBD-51

— 150 180 152H-SC1FBD-52 153H-SC1FBD-52

— 150 210 152H-SC2FBD-52 153H-SC2FBD-52

— 200 260 152H-SC3FBD-54 153H-SC3FBD-54

— 250 320 152H-SD1JBD-56 153H-SD1JBD-56

— 300 361 152H-SD2JBD-57 153H-SD2JBD-57

— 350 420 152H-SD3JBD-58 153H-SD3JBD-58

500/575

— 30 90 152H-SB2FCD-45 153H-SB2FCD-45

— 40 90 152H-SB2FCD-46 153H-SB2FCD-46

— 50 90 152H-SB2FCD-47 153H-SB2FCD-47

— 60 90 152H-SB2FCD-48 153H-SB2FCD-48

— 75 90 152H-SB2FCD-49 153H-SB2FCD-49

— 100 110 152H-SB3FCD-50 153H-SB3FCD-50

— 125 140 152H-SB4FCD-51 153H-SB4FCD-51

— 150 180 152H-SC1FCD-52 153H-SC1FCD-52

— 200 210 152H-SC2FCD-54 153H-SC2FCD-54

— 250 260 152H-SC3FCD-56 153H-SC3FCD-56

— 300 320 152H-SD1JCD-57 153H-SD1JCD-57

— 350 361 152H-SD2JCD-58 153H-SD2JCD-58

— 400 420 152H-SD3JCD-59 153H-SD3JCD-59

— 450 420 152H-SD3JCD-60 153H-SD3JCD-60

§ Requires a bypass contactor. Add -BP or -NB to the end of the catalog number to denote an IEC or NEMA bypass contactor, respectively. Example, for aNEMA bypass contactor, Cat. No. 152H-SB2FBD-44 becomes 152H-SB2FBD-44-NB.

Bulletin 150




Options

Enclosed Options�

Option DescriptionCat. No.

Modification

Push Buttons

Start-Stop Push Button -1

Start-Stop Push Button with H-O-A Selector Switch -1F

Soft Stop Push Button 1XA

Pump Stop Push Button 1XB

Slow Speed Push Button 1XC

Brake Push Button‡ 1XD

Accu-Stop/Slow Speed Push Button‡ 1XE

Selector SwitchHand-Off-Auto Selector Switch -3

SMC-Off-Bypass Selector Switch -3B ∇

Pilot Lights

Transformer Pilot Light - Green Power On Indicator -4G

Transformer Pilot Light - Red Run Indicator -4R

Push-to-Test Pilot Light - Red Run Indicator -5R

Control Circuit Transformer

Control Circuit Transformer (fused primary and secondary) -6P

Additional 100VA Control Circuit Transformer (fused primary and secondary) -6PX

1000VA Control Circuit Transformer (fused primary and secondary) -6PK

1600VA Control Circuit Transformer (fused primary and secondary) -6PL

2000VA Control Circuit Transformer (fused primary and secondary) -6PM

Protective Modules

480V Line Side Protective Module-8L

600V Line Side Protective Module

480V Load Side Protective Module-8M

600V Load Side Protective Module

480V Both Line and Load Side Protective Modules-8B

600V Both Line and Load Side Protective Modules

Communication Module

RS-485 -20S

DeviceNet -20D

Ethernet/IP -20E

Control Net -20C

ProfiBUS -20P

Disconnect AuxiliaryN.O. disconnect auxiliary mounted on operating mechanism -98

N.C. disconnect auxiliary mounted on operating mechanism -99

Circuit Breaker AuxiliaryInternal N.O. circuit breaker auxiliary -98X

Internal N.C. circuit breaker auxiliary -99X

Contactors

IEC Bypass Contactor (does not include overload relay) -BP

NEMA Bypass Contactor (does not include overload relay) -NB

NEMA Isolation Contactor (150B/152B/153B must be selected) -NI

Human Interface Module Door-Mounted, Full Numeric (Type 4/12, includes 3 m cable) -HC6

Service Entrance Label Service Entrance Label -SEL

Oil Pump Starter Bulletin 509 NEMA Size 1starter and Bulletin 592 solid-state overload -OPS

�Add the designated letter to the end of the cat. no. Example: To add the EtherNet/IP option: Cat. No. 152H-SB1FBD-48-1 becomes Cat. No. 152H-SB1FBD-48-1-20E.

∇ Bypass contactor and overload are not included with this option. A -BP or -NB needs to be added to the catalog number to add these devices.

Bulletin 150




Accessories

Option Modules

Current Rating Description Cat. No.

90...520 480V Protective Module 150-F84L

90…520 600V Protective Module 150-F86L

� The same protective module mounts on the line or load side of the SMC-50. Use of protective modules is highly recommended. For applications requiringboth line and load side protection, two protective modules must be ordered.

‡ Protective modules must not be placed on the load (motor) side of an SMC-50 when using an inside-the-delta connection or with pump, braking, or linearspeed acceleration/deceleration control.

DescriptionCompatible Control

Module Ports

Maximum # ofOption Modules of this

Type Per Controller Cat. No.

PTC, Ground Fault, & Current FeedbackOption Module 7 & 8 1 � 150-SM2

Analog I/O Option Module: 2 analog inputs(voltage or current) and 2 analog outputs

(voltage or current)7, 8, 9 3 § 150-SM3

Digital I/O Option Module: 4 100…240V ACinputs and 3 relay outputs 7, 8, 9 3 § 150-SM4

Parameter Configuration Module — DIP androtary dial 7, 8, 9 1 ‡ 150-SM6

�See page 13 for additional information.§ See page 13 for additional information.‡ See page 12 for additional information.

Description Rated Current Cat. No.

Three-Phase Current Monitoring Module

30…180 A�

825-MCM180

181…520 A �‡

825-MCM20

Connection Cable (Replacement) Cat. No. 150-SM2 to Bul. 825-MCM Connection 825-MCA

� Used with a Cat. No. 150-SM2 to provide current feedback to the SMC-50 when in external bypass configuration. ‡ Requires user-supplied current transformers with 5 A secondary.

Option modules can be used to add or expand the functionality of the SMC-50 Control Module. Option modules are installed into the controlmodule's three expansion ports, 7 through 9.NOTE: If network communication is required, a Cat. No. 20-COMM-X communication adapter must be inserted in expansion port 9.

Description Turns Ratio Cat. No.

Core Balance Ground FaultSensor 100:1 § 825-CBCT

§ Used with a Cat. No. 150-SM2 to provide ground current feedback.NOTE: The ground fault sensing feature of the SMC-50 is intended for monitoring purposes only. It is not to be used as a ground fault circuit interrupter forpersonnel protection as defined by Article 100 of the NEC. The sensing feature has not been evaluated to UL 1053.

Protective Modules�‡

Converter Modules

Bulletin 150




Accessories

Description For Use WithPkg.

Quantity Cat. No.IEC line or load terminal cover for 90…180 A devices.

Dead front protectionIP2X finger safe when used with 250 MCM cable

150-SB… FrameB (90…180 A)

units only.1 150-STCB

For Use WithCurrent

Range [A] Wire Size Range

Total No. of Terminal LugsPossible Each Side Pkg.

Qty. Cat. No.Line Side Load Side

150-SB… 90…180 #6…250 MCM AWG16 mm2…120 mm2 3 3 3 199-LF1

150-SC… 210…320 #6…250 MCM AWG16 mm2…120 mm2 6 6 3 199-LF1

150-SD… 361…520 #4…500 MCM AWG25 mm2…240 mm2 6 6 3 199-LG1

SMC-50 Terminal Lug Kits - No Bypass

For Use WithCurrent

Range [A]

Wire Size Range

Total No. ofDistribution Blocks Needed per Side Pkg.

Qty. Cat. No.Line Side Load Side Line Side Load Side

150-SB… 155…311 (2) #4 AWG…500 MCM25…240 mm2

(2) #4 AWG…500 MCM25…240 mm2 3 — 1 1492-BG

150-SC… 363…554 (2) 1/0 AWG…750 MCM54…400 mm2

(6) 6 AWG…250 MCM16…120 mm2 1 — 1

Marathon SpecialProducts Cat. No.

1353703

150-SD… 625…900 (4) 1/0 AWG…750 MCM54…400 mm2

(4) 1/0 AWG…750 MCM54…400 mm2 3 — 1

Marathon SpecialProducts Cat. No.

1352702

For Use WithCurrent

Range [A]

BypassKit Cat.

No.

150-SC… 210…320 150-SCBK

150-SD… 361…520 150-SDBK

�For additional information, see page 8, page 43, and page 47.

IEC Terminal Covers

SMC-50 Terminal Lug Kits - With Bypass

Inside-the-Delta Distribution Blocks

For Use WithCurrent

Range [A] Wire Size Range

Total No. ofTerminal Lugs

Possible Each Side Pkg.Qty.

Lug Cat.No.Line Side Load Side

150-SB… 90…180 (2)#6…250 MCM AWG16 mm2…120 mm2 3 3 3 1494R-N14

150-SC… 210…320 #6…250 MCM AWG16 mm2…120 mm2

6 (6 additionalneeded for bypass

kit)6 3 199-LF1

150-SD… 361…520 #4…500 MCM AWG25 mm2…240 mm2

6 (6 additionalneeded for bypass

kit)6 3 199-LG1

Bypass Kits�

Bulletin 150




Accessories

Human Interface Modules (HIM) & Communication Modules

Description Cat. No.

SMC-50 Controller — Bezel-Mounted Enhanced, LCD, Full Numeric Keypad 20-HIM-A6

Door-Mounted HIM Remote (panel mount) LCD Display, Full Numeric Keypad(version of Cat. No. 20-HIM-A6) ‡ 20-HIM-C6S

HIM Interface Cables

HIM Interface Cable, 1 m (39 in) � 20-HIM-H10

Cable Kit (Male-Female) 0.33 m (1.1 ft) 1202-H03

Cable Kit (Male-Female) 1 m (3.3 ft) 1202-H10



DPI/SCANport™ One to Two Port Splitter Cable 1203-S03

Description (IP30/Type 1) For Use With

Communication Modules(installed into the physicalspace assigned to controlmodule expansion port 9;

connected to DPI port 4 viacable)

RS485 DF1 Communication Adapter

Bulletin 150-Sxx

20-COMM-S

PROFIBUS™ DP Communication Adapter 20-COMM-P

ControlNet™ Communication Adapter (Coax) 20-COMM-C

Interbus™ Communication Adapter 20-COMM-I

Modbus/TCP Communication Adapter 20-COMM-M

DeviceNet™ Communication Adapter 20-COMM-D

EtherNet/IP™ Communication Adapter 20-COMM-E

Dual-port EtherNet/IP™ Communication Adapter 20-COMM-ER

HVAC Communication Adapter 20-COMM-H

ControlNet™ Communication Adapter (Fiber) 20-COMM-Q

Connected Componets Workbench

Programming Software Windows7/2000/XP/Vista

Available for download atwww.rockwellautomation.com

DriveExecutive™ 9303-4DTE01ENE

DriveTools™ SP ♣ 9303-4DTS01ENE

AnaCANda™ RS-232 to DPIPC Interface

Serial ♦ 1203-SSS

DPI to USB USB ♠ 1203-USB

� A cable is required if 20-HIM-A6 is connected to the SMC-50 DPI Port #2 and used as a handheld device.‡ A 3 m (9.8 ft.) 1202-C30 cable is provided. ♣ Includes DriveExecutive™ and DriveObserver™ .♦ Includes Cat. No. 1203-SFC and 1202-C10 cables.♠ Includes Cat. No. 20-HIM-H10 and 22-HIM-H10 cables.

Bulletin 150




Renewal Parts

Spare or Replacement PartsSpare or Replacement Power Poles and Assembies

Description

100…240V ACControl Voltage

24V DC ControlVoltage

Cat. No. Cat. No.

Frame B Power Structure Assembly(Contains all three power poles in a single package andincludes the pole-to-control module transition cover and

cooling fan.)

90 A, 200…480V AC line 150-SPPB1B 150-SPPB1BR




90 A, 200…690V AC line 150-SPPB1U 150-SPPB1UR




Frame C Power Pole(Contains one power pole — SCR and heatsink

assembly and cable.)

210 A, 200…480V AC line 150-SPPC1B

260 A, 200…480V AC line 150-SPPC2B

320 A, 200…480V AC line 150-SPPC3B

210 A, 200…690V AC line 150-SPPC1U

260 A, 200…690V AC line 150-SPPC2U

320 A, 200…690V AC line 150-SPPC3U

Frame D Power Pole(Contains one power pole — SCR and heatsink

assembly and cable.)

361 A, 200…480V AC line 150-SPPD1B

420 A, 200…480V AC line 150-SPPD2B

520 A, 200…480V AC line 150-SPPD3B

361 A, 200…690V AC line 150-SPPD1U

420 A, 200…690V AC line 150-SPPD2U

520 A, 200…690V AC line 150-SPPD3U

Description Cat. No.

SMC-50 Control Module100…240V AC control power; two 24V DC inputs, two relay outputs 150-SCMD

24V DC control power; two 24V DC inputs, two relay outputs 150-SCMR

Description Rated Control Voltage For Use With Cat. No.

Replacement Fan

Replacement fan for SMC-50Frame B

100…240V AC90…180 A units

150-SF1

24V DC 150-SF1R

Replacement fan for SMC-50Frame C

100…240V AC210…320 A units

150-SF2D

24V DC 150-SF2R

Replacement fan for SMC-50Frame D

100…240V AC361…520 A units

150-SF3D

24V DC 150-SF3R

Replacement Fan Cover

Replacement fan cover for SMC-50 Frame B 90…180 A units 150-SBFC

Replacement fan cover for SMC-50 Frame C 210…320 A units 150-SCFC

Replacement fan cover for SMC-50 Frame D 361…520 A units 150-SDFC

Replacement Cover

Replacement control module front cover 90…520 A units 150-SCMRC

Replacement controller cover210…320 A units 150-SCRC

361…520 A units 150-SDRC

Replacement RemovableTerminal Block

Control module control I/O replacement removable terminal block Control module 150-SCMRTB

PTC module replacement removable terminal block (set of 3) 150-SM2 150-SM2RTB

Analog I/O option replacement removable terminal block 150-SM3 150-SM3RTB

Digital I/O module replacement removable terminal block 150-SM4 150-SM4RTB

Replacement Parts

Spare or Replacement Control Module

Bulletin 150




Specifications

Functional Design

Standard Features Description

InstallationPower Wiring standard squirrel-cage induction motor or a Wye-Delta, six-lead motor

Control Wiring 2- and 3-wire control for a wide variety of applications

Configuration/Setup�

Keypad Cat. No. 20-HIM-A6 full numeric keypad with LCD displayCat. No. 20-HIM-C6S remote panel mount full numeric keypad with LCD display

Software parameter values are downloaded to the SMC-50 with the DriveTools and DriveExplorerprogramming software

Parameter ConfigurationOption Module (PCM) Cat. No. 150-SM6 provides simple and limited configuration by DIP and rotary dial switches

Communications four DPI ports for local serial communications. Network communication supported by optional 20-COMM-X modules

Starting & Stopping Modesmodes include: Soft Start, Coast-to-Stop, Soft Stop, Current Limit Start, Dual Ramp, Full Voltage,Linear Speed Acceleration (start), Linear Speed Deceleration (stop), Torque Start, and Preset Slow

Speed

Pump Control Start & Stop helps reduce fluid surges in centrifugal pumping systems during the starting and stopping period

Braking ControlΔ

SMB Smart Motor Braking provides motor braking without additional equipment for applications that require the motor to stopquickly

Accu-Stop♣

provides controlled position stopping; during stopping, brake torque is applied to the motor untilthe motor reaches the preset slow speed and holds the motor at this speed until a stop command

is given - braking torque is then applied until the motor reaches zero speed - braking current isprogrammable

Slow Speed with Braking used on applications that require slow speed (in the forward or reverse direction) for positioning oralignment and requires braking control to stop

External Braking activates the external braking device by using aux. relay output

Protection & Diagnostics‡displays: Power Loss, Line Fault, Voltage Unbalance, Excessive Starts/Hour, Phase Reversal,

Undervoltage, Overvoltage, Controller Temperature, Stall, Jam, Open Gate, Overload, Underload,and Communication Fault

Metering Indication§

provides: Phase Current, Current Average, Phase-to-Phase Voltage, Voltage P-P Average, Phase-to-Neutral Voltage, Calculated Torque, Real Phase Power, Real Power, Real Energy, Real Demand,

Max Real Demand, Reactive Power, Reactive Energy + & -, Reactive Energy, Reactive Demand,Max Reactive Demand, Apparent Power, Apparent Energy, Apparent Demand, Number of Periods,Power Factor, Energy Savings, Elapsed Time 1 & 2, Running Time, Motor Speed, Start Time 1-5,

Peak Current 1-5, Total Starts, THD V, THD I, THD V Average, THD I Average, Line Frequency,Current Imbalance, and Voltage Unbalance

LED Status Indication by Multi-color (standard)displays fault and alarm codes: Running - with alarm, Running - no alarm, Ready - with alarm,Ready - no alarm, Ready - tuning enabled on next start, and Firmware Download Active - with

alarm

Auxillary Contacts (two standard) two fully programmable contacts as: normal, UTS, fault, alarm, external brake, auxilliary control,network, or external bypass

�The configuration method must be ordered separately from the controller which doers not include a setup tool.‡ Diagnostic indication depends on the type of configuration tool used, The standard LED status indication displays: Inhibit (stop enabled), Fault (non-

resettable), Fault (resettable). For full local access, a HIM or PC software is required, For network access, full access to data can also be obtained.§ Metering Indication depends on the type of configuration tool being used. Metering Indication requires the use of a HIM or a PC software configuration tool

for full local access. Full access to data can also be obtained via network.♣ Accu-Stop is not included as a parameter/function like that of the SMC-Flex. However, the Accu-Stop function can be accomplished with the SMB mode and

Slow Speed with Braking functions.Δ Not intended to be used as an emergency stop. Refer to the applicable standards for emergency stop requirements.

Bulletin 150




Specifications

Electrical Ratings

DescriptionDeviceRating

UL/CSA/NEMA IECPower Circuit

Rated Operation Voltage480V 200…480V AC (–15%, +10%) 200…415V (-15%, +10%)690V 200…600V AC (–15%, +10%) 200…690V/Y (–15%, +10%)

Rated Insulation Voltage480V N/A 500V690V N/A 690V

Rated Impulse Voltage480V N/A 6000V690V N/A 6000V

Dielectric Withstand480V 2200V AC 2500V690V 2200V AC 2500V

Repetitive Peak Inverse Voltage Rating480V 1400V 1400V690V 1800V 1800V

Operating Frequency All 47...63 Hz 47...63 HzUtilization Category UL/CSA/NEMA IEC

Normal Duty90…520 A MG 1

AC-53a:3.5-10:99-2Heavy Duty AC-53a:3.5-30:99-1

Protection Against Electrical Shock90…520 A

N/AIP00 (IP20 - Control Terminals only)

90…180 A IP2X (with Cat. No. 150-STCB Terminal Cover)

DV/DT Protection480V

RC Snubber Network690V

Transient Protection480...600V Metal Oxide Varistors: 220 Joules

690V NoneControl Power Specifications UL/CSA/NEMA IEC

Rated Operational Voltage 100…240V AC (-15%…+10%) or 24V DC (-10%…+10%)Rated Insulation Voltage NA 240VRated Impulse Voltage NA 3000VDielectric Withstand 1500V AC 1500VOperating Frequency 47…63 Hz or DCControl Power Ride Through 22 msMax. Output of 24V DC Supply (Terminals 8 & 12) 300 mAControl Module Battery Type CR 2032Control Module Standard Inputs: Terminals 10 & 11 UL/CSA/NEMA IEC

Nominal Operating Voltage 24V DCOperating Voltage Range 15…30V DC

On StateMin. Current 2.8 mAMin. Voltage 10V DC

Off StateMax. Current 3 mAMax. Voltage 10.9V DC

Inrush Current Maximum 7 mAInput Delay Time On-to-Off: 30 ms, Off-to-On: 20 msReverse Polarity Protection YesRated Insulation Voltage NA 60VRated Impulse Voltage NA 500VDielectric Withstand 500V AC 1000V AC

Control Module Standard Outputs: Terminals 4/5 &6/7 UL/CSA/NEMA IEC

Outputs Aux 1, Aux 2Type of Control Circuit Electromagnetic RelayNumber of Contacts per Relay 1Type of Contacts Programmable N.O./N.C. (electrically held closed)Type of Current ACRated Operational Current 3 A @ 120V AC, 1.5 A @ 240V ACConventional Thermal Current Ith AC/DC 5AMake/Break VA 3600/360Utilization Category B300 AC-15Off-State Leakage Current 0.024 mA @ 24VOff-State Leakage Current 0.12 mA @120VOff-State Leakage Current 0.24 mA @ 240V

Wiring Terminals (applies to Control Module Standard I/O & Expansion Module Terminals 150-SM2, 150-SM3, 150-SM4)Terminal Style M3 Screw ClampTerminal Type RemovableScrew Terminal Torque 0.8 N m (7.0 lb-in)

Terminal Wire Size 0.2..2.5 mm2 (24...14 AWG)Wire Strip Length 7.0 mm (0.27 in.)

Bulletin 150




Specifications

Description

UL/CSA/NEMA IECCat. No. 150-SM4 Optional Digital Control Inputs:

Terminals A1 & A2Nominal Operating Voltage 100…240V ACOperating Voltage Range 85V…264V AC @ 47 Hz…63 Hz

On StateMin. Current 9.7 mA @ 47 Hz, 9.7 mA @ 62.4 HzMin. Voltage 74.5V AC @ 47 Hz, 55.9V AC @ 62.4 Hz

Off StateMax. Current 9.0 mA @ 47 Hz, 9.3 mA @ 62.4 HzMax. Voltage 68.8V AC @ 47 Hz, 53.6V AC @ 62.4 Hz

Inrush Current Maximum 3.64 AInput Delay Time On-to-Off: 30 ms, Off-to-On: 25 msRated Insulation Voltage NA 240VRated Impulse Voltage NA 3000VDielectric Withstand 1600V AC 2000V AC

Cat. No. 150-SM4 Optional Digital Control Inputs:Terminals A3 & A4� UL/CSA/NEMA IEC

Nominal Operating Voltage 100…240V ACOperating Voltage Range 85V…264V AC @ 47 Hz…63 Hz

On StateMin. Current 5.1 mA @ 47 Hz, 5.0 mA @ 62.4 HzMin. Voltage 74.5V AC @ 47 Hz, 55.8V AC @ 62.4 Hz

Off StateMax. Current 4.7 mA @ 47 Hz, 4.8 mA @ 62.4 HzMax. Voltage 68.6V AC @ 47 Hz, 53.5V AC @ 62.4 Hz

Inrush Current Maximum 3.64 AInput Delay Time On-to-Off: 30 ms, Off-to-On: 25 msRated Insulation Voltage NA 240VRated Impulse Voltage NA 3000VDielectric Withstand 1600V AC 2000V AC

Cat. No. 150-SM4 Optional Outputs: TerminalsA6/A7, A8/A9, A10/A11 UL/CSA/NEMA IEC

Outputs Aux 1, Aux 2, Aux 3Type of Control Circuit Electromagnetic RelayNumber of Contacts per Relay 1Type of Contacts Programmable N.O./N.C. (electrically held closed)Type of Current ACRated Operational Current 3 A @ 120V AC, 1.5 A @ 240V ACConventional Thermal Current Ith AC/DC 5AMake/Break VA 3600/360Utilization Category B300 AC-15

Off-State Leakage Current0.024 mA @ 24V0.12 mA @120V0.24 mA @ 240V

� Meets IEC Type 2 specifications for inputs per IEC 60947-1 for 240V AC only.

Bulletin 150




Specifications

Cat. No. 150-SM3 Optional Analog Control Inputs: Terminals B5…B10Number of Inputs 2 differential inputsNormal Operating Input Ranges ±10V, 0…10V, 0…5V, 1…5V, 0…20 mA, 4…20 mAFull Scale Operating Input Ranges ±10.5V, 0…10.5V, -0.5…5.25V, 0.5…5.25V, 0…21 mA, 3.5…21 mAInput Resolution 16 bit (sample rate = 60 Hz)/13 bit (sample rate = 250 Hz)Data Refresh Rate Filter dependent: 100 ms (sample rate = 60Hz);24 ms (sample rate = 250Hz)Rated Working Voltage 24V DC / 17V ACCommon Mode Voltage Range ±10V DC / channel

Input Impedance220 kΩ: voltage mode249 Ω: current mode

Input Channel Diagnostics Over and Under Range and Open CircuitOpen Circuit Detection Time Positive Full Scale Reading: within 3 seconds (max)

Maximum Overload at Input TerminalsVoltage: ±24V DC continuous at 0.1 mACurrent: ±30 mA continuous at 7V DC

External Calibration Not required: auto-calibration performed by the module if required to meet specs.Module Isolation to Control Board Yes (1000V AC)Removable Terminal Block Yes (Cat. No.150-SM3RTB as a spare replacement part)

Cable Type Belden 8760 (or equiv.) 0.750 mm2 (18 AWG twisted pair 100% shield with drain)Cat. No. 150-SM3 Optional Analog Control Outputs: Terminals B1…B4

Number of Outputs 2 Single-endedNormal Operating Ranges ±10V, 0…10V, 0…5V, 0…20 mA, 4…20 mAFull Scale Operating Ranges ±10.5V, 0…10.5V, -0.5…5.25V, 0…21 mA, 3.5…21 mAOutput Resolution±10.5V, 0 …10.5V, -0.5…5.25V,0…21 mA, 3.5 …21 mA

16 bit (15 plus sign bipolar)

Resistive Load on Current Output 0…750 ΩLoad Range on Voltage Output 1 kΩ at 10V DCMax. Inductive Load (Current Outputs) 15 mHMax. Capacitive Load (Voltage Outputs) 100 μF

Overall AccuracyVoltage Terminal: ±0.5% full scale at 25° C

Current Terminal: ±0.35% full scale at 25° CAccuracy Drift with Temperature ±5 PPM / ° COutput Impedance 15 Ω (typical)Open and Short-Circuit Protection YesMaximum Short-Circuit Current 45 mAOutput Overvoltage Protection Yes

PTC Input RatingsPTC Input Ratings (Cat. No. 150-SM2 required)

Response Resistance 3400 Ω ± 150 ΩReset Resistance 1600 Ω ± 100 ΩShort-Circuit Trip Resistance 25 Ω ± 10 ΩMax. Voltage at PTC Terminals (RPTC = 4 kΩ) < 7.5 V

Max. Voltage at PTC Terminals (RPTC = open) 30VMax. No. of Sensors (wired in series) 6Max. Cold Resistance of PTC Sensor Chain 1500 ΩResponse Time 800 ms

Bulletin 150




Specifications

Control Power Requirements (Maximum Control Circuit Consumption)

Base Power Draw: Control Module with Heat Sink Fan

Current Range [A]Control Voltage

100…240V AC 24V DC90…180 150 VA 75 W

210…260 150 VA 75 W361…520 300 VA 300 W

Option Power Adder (for each option installed, add to basepower to obtain total power requirement)

Human Interface Module (HIM) 10 VA 2 W150-SM2� 30 VA 4 W150-SM3 30 VA 4 W150-SM4 50 VA 2 W

150-SM6� 5 VA 1 W

20-COMM-X� 25 VA 4 W

Continuous Duty Power Structure Heat Dissipation at Rated Current (Watts)

Controller Rating [A]

90 270110 330140 420180 540210 630260 780320 960361 1083420 1260520 1560

�Max. one of each option type per control module.

Max. Total PowerDissipation = = + + Watts

Base Power Options Power Structure

Power Calculation:

Max. Total PowerDissipation = = 300 + (25 + 10 + 50) + 1083

WattsBase Power Options Power Structure

Max. Total Power Dissipation = 1468 Watts

Example: 361 A device with a 20-COMM-X, HIM, and Cat. No. 150-SM4

Electrical Specifications

Bulletin 150




Specifications

SCPD Performance, Type 1SCPD Performance� Type 1♣

Motor Connection Type Cat. No.

CurrentRating

[A]

Non-Time Delay Fuse‡ Time Delay Fuse§Inverse Time (Thermal Magnetic)

Circuit Breaker

Max.StandardAvailableFault [kA]

TypicalAmps

Max.Amps


TypicalAmps

Max.Amps


TypicalAmps

Max.Amps

LineΔ

150-SB1N… 90

10

250 350

10

150 200

10

225 350

150-SB2N… 110 300 400 175 225 250 300

150-SB3N… 140 400 500 225 300 350 400

150-SB4N… 180 500 300 400 450 500

150-SC1N… 210

18

600

18

350 450

18

500 600

150-SC2N… 260 700 450 500 600 700

150-SC3N… 320 800 500 700 800 800

150-SD1N… 361

30/18♠1000

30/18♠600 800

30/18♠800 1000

150-SD2N… 420 1200 700 800 1000 1200

150-SD3N… 520 1200 800 1000 1200 1200

Inside Delta♦

150-SB1N… 155

18

450

18

250 300

18

350 450

150-SB2N… 190 500 300 400 450 500

150-SB3N… 242 700 400 500 600 700

150-SB4N… 311 800 500 600 700 800

150-SC1N… 363

30

1000

30

600 800

30

800 1000

150-SC2N… 450 1200 700 1000 1000 1200

150-SC3N… 554 1600 800 1200 1200 1600

150-SD1N… 625

42

1600

42

1000 1200

42

1200 1600

150-SD2N… 727 2000 1200 1600 1600 2000

150-SD3N… 900 2500 1200 2000 2000 2500

�Consult local codes for proper sizing of short-circuit protection.‡ Non-Time Delay Fuses: Class K5 up to 600 A, Class L above 600 A.§ Time Delay Fuse: Devices rated 90…180 A (155…311 A): Class RK5. Devices rated 210…520 A (363…900 A): Class RK5 or Class J up to 600 A, Class L

above 600 A♣ Basic Requirements for Type 1 Coordination: Under the short-circuit condition, the starter shall cause no danger to persons or to the installation. The starter

may not be suitable for further service without repair or replacement of parts. For further details, refer to UL 508/CSA C22.2 No. 14 and EN 60947-4-2.Δ UL/CSA (Type 1) & EN 60947-4-2 (Type 1) for Line-Connected Motors: Suitable for use on a circuit capable of delivering not more than the listed max. RMS

symetrical amperes (UL: 600V maximum, IEC: 690V maximum).♦ UL/CSA (Type 1) & EN 60947-4-2 (Type 1) for Inside-the-Delta Connected Motors: Suitable for use on a circuit capable of delivering not more than the

listed max. RMS symetrical amperes (UL & IEC: 600V maximum).♠ UL/CSA applications = 30 kA, 600V maximum. IEC applications = 18 kA, 690V maximum.

Bulletin 150




Specifications

Semiconductor (SCR) Fusing�

Cat. No.

Current Rating [A]I2t Reference

(103A2s)

North America‡§ Type 2 Coordination Per EN 60947-4-2§♣

LineΔInsideDelta♦

Max. Available Fault(480V) [kA] Fuse Part No.♠

Max. Available Fault(500V) [kA] Fuse Part No.♠

150-SB1N… 90 155 92

65

A70QS150

65

6,9URD30*0200150-SB2N… 110 190 95 A70QS175 6,9URD30*0200150-SB3N… 140 242 100 A70QS200 6,9URD30*0250150-SB4N… 180 311 106 A70QS250 6,9URD31*0315150-SC1N… 210 363 200 A70QS350 6,9URD30*0315150-SC2N… 260 450 238 A70QS400 6,9URD31*0400150-SC3N… 320 554 320 A70QS450 6,9URD31*0450150-SD1N… 361 625 1000 A70QS500 6,9URD31*0500150-SD2N… 420 727 1100 A70QS600 6,9URD31*0630150-SD3N… 520 900 1200 A70QS700 6,9URD31*0700

�Consult local codes for proper sizing of short-circuit protection. ‡ Calculated only, NOT tested. § Fuse size based on a start profile of 350% of the controller maximum current rating for 10 seconds. Contact Technical Support at

[email protected] or 440-646-5800 for applications with a longer start time or higher starting current.♣ Basic Requirements for Type 2 Coordination: Per EN 60947-4-2 under short-circuit conditions, the device shall cause no danger to persons or installation

and shall be suitable for further use. Δ For line-connected motors, connect fuses to the SMC-50 in line with three-phase power terminals L1, L2, and L3.♦ For delta-connected motors, connect fuses to the SMC-50 inside the delta after terminals L1-T6, L2-T4, and L3-T5.♠ Ferraz Shawmut - Mersen part number

SCPD Performance� Type 1‡

Motor Connection Type Cat. No.

CurrentRating

[A]

Class J or Class L Fuse§Inverse Time (Thermal Magnetic) Circuit Breaker♣

480V, 65kA MaximumMax. HighCapacityAvailable

Fault (600V)[kA]

TypicalAmps Max. Amps

Bul. 140UFrameSizeΔ Max. Amps Cat. No.Δ Rating Plug

Line

150-SB1N… 90

100

150 200

M

350 140U-M6D3-D35 N/A150-SB2N… 110 175 225 300 140U-M6D3-D30 N/A150-SB3N… 140 225 300 400 140U-M6D3-D40 N/A150-SB4N… 180 300 400 400 140U-M6D3-D40 N/A150-SC1N… 210 350 450

M600 140U-M6D3-D60 N/A

150-SC2N… 260 450 500 700 140U-M6D3-D70 N/A150-SC3N… 320 500 700 800 140U-M6D3-D80 N/A150-SD1N… 361 601 800

N1000 140U-N6L3-E12 140U-NRP3-E10

150-SD2N… 420 700 800 1200 140U-N6L3-E12 140U-NRP3-E12150-SD3N… 520 800 1000 1200 140U-N6L3-E12 140U-NRP3-E12

Inside Delta

150-SB1N… 155

65

250 300

M

450 140U-M6D3-D45 N/A150-SB2N… 190 300 400 500 140U-M6D3-D50 N/A150-SB3N… 242 400 500 700 140U-M6D3-D70 N/A150-SB4N… 311 500 600 700 140U-M6D3-D70 N/A150-SC1N… 363 601 800

N1000 140U-N6L3-E12 140U-NRP3-E10

150-SC2N… 450 700 1000 1200 140U-N6L3-E12 140U-NRP3-E12150-SC3N… 554 800 1200 1200 140U-N6L3-E12 140U-NRP3-E12150-SD1N… 625 1000 1200

R1600 140U-R6L3-E20 140U-R20RP3-E16

150-SD2N… 727 1200 1600 2000 140U-R6L3-E20 140U-R20RP3-E20150-SD3N… 900 1200 2000 2000 140U-R6L3-E20 140U-R20RP3-E20

�Consult local codes for proper sizing of short-circuit protection. ‡ Basic Requirements for Type 1 Coordination: Under the short-circuit condition, the starter shall cause no danger to persons or to the installation. The starter

may not be suitable for further service without repair or replacement of parts. For further details, refer to UL 508/CSA C22.2 No. 14 and EN 60947-4-2§ High Capacity fault ratings when used with time delay Class J or time delay Class L fuse♣ Circuit Breaker must be of the designated 140U FrameΔ Other circuit breakers pending

Bulletin 150




Specifications

Environmental

Operating Ambient Temperature Range (surrounding air ambient)-20…+40 °C (-4…+104 °F) (no derating) —

For operation 40...65 °C (104...149 °F), refer to Thermal Wizard.-5…+40 °C (23…104 °F) (Enclosed)

Storage & Transportation Temperature Range –25…+75 °C (-13…+167 °F)

Altitude 2000 m (6560 ft) without derating; for operation above 2000...7000 m(6560...22965 ft) maximum, refer to Thermal Wizard

Humidity 5…95% (non-condensing)Pollution Degree 2Mounting Orientation VerticalAtmospheric Protection ANSI/ISA - 71.04-2013; Class G3 Environment

Mechanical

Resistance to VibrationOperational

90…520 A1.0 G Peak, 0.15 mm (0.006 in.) Displacement

Non-Operational 2.5 G Peak, 0.38 mm (0.015 in.) Displacement

Resistance to ShockOperational

90...520 A15 G

Non-Operational 30 G

Construction

Power Poles Heatsink Hockey Puck Thyristor Modular Design

Control Modules Thermoset and Thermoplastic Moldings

Metal Parts Plated Brass, Copper, or Steel

TerminalsPower Terminal Lugs

90…180 A One 10.5 mm (0.41 in.) diameter hole per power pole

210…320 A Two 10.5 mm (0.41 in.) diameter holes per power pole

361…520 A Two 13.5 mm (0.53 in.) diameter holes per power pole

Power Terminal Markings NEMA, CENELEC EN50 012

Control Terminals M3 ScrewClamp Clamping Yoke Connection

Other EN

EMC Emission Levels Conducted Radio Frequency EmissionsRadiated Emissions

Class A (per EN 60947-4-2)Class A (per EN 60947-4-2)

EMC Immunity Levels

Electrostatic DischargeRadio Frequency Electromagnetic FieldFast TransientSurge Transient

8 kV Air DischargePer EN 60947-4-2Per EN 60947-4-2Per EN 60947-4-2

Overload Characteristics Line Delta

Current Range

90 30...90 52…155

110 37…110 65…190

140 47…140 82…242

180 60…180 104…311

210 70…210 122…363

260 87…260 151…450

320 107…320 186…554

361 120…361 210…625

420 140…420 243…727

520 174…520 302…900

Overload Type Electronic - using I2t algorithm

Trip Classes 5 to 30

Trip Current Rating 118% of Motor FLC

Number of Poles 3

Certifications Open-Type Controllers CE Marked Per Low Voltage Directive 73/23/EEC, 93/68/EECUL Listed (File No. E96956)

Environmental, Mechanical, & Other Specifications

Bulletin 150




Specifications

Protection Device & Bypass Component Selection Overview — Line Connected Motor

Description

SMC-50 Cat. No.‡

150-SB1N* 150-SB2N* 150-SB3N* 150-SB4N* 150-SC1N* 150-SC2N* 150-SC3N* 150-SD1N* 150-SD2N* 150-SD3N*

Rated Current [A] 90 110 140 180 210 260 320 361 420 520

Voltage 230…600VAC

230…600VAC

230…600VAC

230…600VAC

230…600VAC

230…600VAC

230…600VAC

230…600VAC

230…600VAC

230…600VAC

Short-Circuit Current Ratings (SCCR)§

Standard Fault SCCR at 600V

Std. Available Fault [kA] 10 18 30

Max. Non-Time DelayFuse 350 A 400 A 500 A 500 A 600 A 700 A 800 A 1000 A 1200 A 1200 A

Max. Time Delay Fuse 200 A 225 A 300 A 400 A 450 A 500 A 700 A 800 A 800 A 1000 A

Max. Inverse Time CircuitBreaker (CB) 350 A 300 A 400 A 500 A 600 A 700 A 800 A 1000 A 1200 A 1200 A

High Fault SCCR

High Available Fault withFuses at 600V [kA] 100

Max. Class J or L TimeDelay Fuse 200 A 225 A 300 A 400 A 450 A 500 A 700 A 800 A 800 A 1000 A

High Available Fault withCircuit Breaker at 480V

[kA]65

Max. Inverse Time CB(Bul. 140U required)♣ 350 A 300 A 400 A 400 A 600 A 700 A 800 A 1000 A 1200 A 1200 A

Bul. 140U MCCB FrameSize M M N

Branch Protection Reference§

Inverse Time Circuit Breaker Selections‡

35 kA at 600V Maximum 140G-K6F3-D*

140G-K6F3-D*

140G-K6F3-D*

140G-K6F3-D*

140G-M6F3-D*

140G-M6F3-D*

140G-M6F3-D*

140G-N6H3-E12

140G-N6H3-E12

140G-N6H3-E12

65 kA at 480VMaximum♣

140U-M6D3-D*

140U-M6D3-D*

140U-M6D3-D*

140U-M6D3-D*

140U-M6D3-D*

140U-M6D3-D*

140U-M6D3-D*

140U-N6L3-E12Δ

140U-N6L3-E12Δ

140U-N6L3-E12Δ

Fused Disconnect Selections

For Use With Time DelayFuses

194R-J200-1753

194R-J400-1753

194R-J400-1753

194R-J400-1753

194R-J600-1753

194R-J600-1753

194R-L800-1753 — — —

Bypass Contactor Reference‡§♦

AC-3 Rated per UL/CSA♠

Standard Fault SCCR

Short Circuit CurrentRatings @ 600V with: 100-C97* 100-D115* 100-D140* 100-D180* 100-D250* 100-D250* 100-D300* 100-D630* 100-D630* 100-D630*

Standard Available Fault[kA] 10 18 30


High Fault SCCR

Short Circuit CurrentRatings with: 100-C97* 100-D115* 100-D140* 100-D180* 100-D210* 100-D250* 100-D300* 100-D420* 100-D630* 100-D630*

High Available Fault withFuses at 600V [kA] 100 100 100 42

Max. Class J or Class LTime Delay Fuse 120 A 150 A 200 A 225 A 300 A 350 A 450 A 500 A 600 A 700 A

‡ For complete catalog numbers, refer to the online catalog: www.rockwellautomation.com or appropriate manufacturer's website§ Always refer to local codes for proper selection of branch circuit components.♣ Circuit Breaker must be of the designated 140U Frame size for high fault short circuit ratings. Other circuit breakers pending.Δ Requires rating plug selection based on application, refer to the online catalog: www.rockwellautomation.com♦ For most up to date information including voltage ratings other than 600V please see the Global SCCR Tables at www.rockwellautomation.com♠ In IEC regulated regions when sizing the bypass contactor per AC-1 or AC-3 ratings, the short circuit rating of the bypass contactor must be similar to the

SMC-50.

Bulletin 150




Specifications

Line-Connected Motor Wiring Diagram using Bul. 825 Converter Module and Cat. No. 150-SM2 Devices withBypass Contactor

Motor

SMC-50

T1/2 T2/4 T3/6

T1

T2

T3

L1/1 L2/3 L3/5

Branch Protection Device(CB or Fused Disconnect)

825-MCMxx

AC-3 or AC-1 RatedBypass Contactor

SCR Fusing

L1 L2 L3

§

♣

‡ The 825-MCMxx provides current feedback to the SMC-50 when RUN in Bypass Operation. A Cat. No.150-SM2 is also required. For30…180 A, use Cat. No. 825-MCM180; For 181…520A, use Cat. No. 825-MCM20 and user-supplied CTs with 5A secondary.§Due to current leakage through an SCR in the OFF state (controller stopped), some form of upstream line power isolation is recommended ifmaintenance is required on the motor. See the isolation contactor application information for details.♣Bypass must be controlled by an auxiliary contact of the SMC-50 configured to exernal bypass.

Bulletin 150




Specifications

Line Connected Motor Wiring Diagram for Cat. No. 150-SC… or 150-SD… Devices with Bypass Contactorand Bypass Bus Kit

Motor

SMC-50

T1/2 T2/4 T3/6

T1

T2

T3

L1/1 L2/3 L3/5



SCR Fusing

L1 L2 L3

§

♣

‡ SMC-50 Bypass Bus Kit Cat. No. 150-SCBK or -SDBK is required.§Due to current leakage through an SCR in the OFF state (controller stopped), some form of upstream line power isolation is recommended ifmaintenance is required on the motor. See the isolation contactor application information for details.♣Bypass must be controlled by an auxiliary contact of the SMC-50 configured to exernal bypass.NOTE: Controller FRN 3.001or higher is required.

Bulletin 150




Specifications

Line Connected Motor Wiring Diagram with Bypass and External Overload

Motor

SMC-50

T1/2 T2/4 T3/6

T1

T2

T3

L1/1 L2/3 L3/5


Thermal MagneticOverload Relay


SCR FusingIsolation Contactor (A)

Isolation Contactor (B)

L1 L2 L3

Δ

§

§ Overload is required.NOTE: Bypass must be fully rated to motor Hp/kW and FLA.♣ Isolation Contactors A and B are required if bypass is used for emergency START, STOP, and RUN operation.‡Due to current leakage through an SCR in the OFF state (controller stopped), some form of upstream line power isolation is recommended ifmaintenance is required on the motor. See the isolation contactor application information for details.ΔBypass must be controlled by an auxiliary contact of the SMC-50 configured to exernal bypass.

Bulletin 150




Specifications

Protection Device & Bypass Component Selection Overview — Delta Connected Motor

Description

SMC-50 Cat. No.‡

150-SB1N* 150-SB2N* 150-SB3N* 150-SB4N* 150-SC1N* 150-SC2N* 150-SC3N* 150-SD1N* 150-SD2N* 150-SD3N*

Rated Current [A] 155 190 242 311 363 450 554 625 727 900

Voltage 230…600VAC

230…600VAC

230…600VAC

230…600VAC

230…600VAC

230…600VAC

230…600VAC

230…600VAC

230…600VAC

230…600VAC

Short-Circuit Current Ratings (SCCR)�

Standard Fault SCCR at 600V

Std. Available Fault [kA] 18 30 42


Max. Time Delay Fuse 300 A 400 A 500 A 600 A 800 A 1000 A 1200 A 1200 A 1600 A 2000 A

Max. Inverse Time CircuitBreaker (CB) 450 A 500 A 700 A 800 A 1000 A 1200 A 1600 A 1600 A 2000 A 2500 A

High Fault SCCR

High Available Fault withFuses at 600V [kA] 65

Max. Class J or L TimeDelay Fuse 300 A 400 A 500 A 600 A 800 A 1000 A 1200 A 1200 A 1600 A 2000 A

High Available Fault withCircuit Breaker at 480V

[kA]65

Max. Inverse Time CB(Bul. 140U required)∇ 450 A 500 A 700 A 700 A 1000 A 1200 A 1200 A 1600 A 2000 A 2000 A

Bul. 140U MCCB FrameSize M N R

Branch Protection Reference�

Inverse Time Circuit Breaker Selections‡

35 kA at 600V Maximum 140G-K6F3-D*

140G-M6F3-D*

140G-M6F3-D*

140G-M6F3-D*

140G-N6H3-E12

140G-N6H3-E12 — — — —

50 kA at 600V Maximum — — — — — — 140G-R12I3-E20

140G-R12I3-E20

140G-R12I3-E20

140G-R12I3-E25

65 kA at 480VMaximum∇

140U-M6D3-D*

140U-M6D3-D*

140U-M6D3-D*

140U-M6D3-D*

140U-N6L3-E12§

140U-N6L3-E12§

140U-N6L3-E12§

140U-R6L3-E20§

140U-R6L3-E20§

140U-R6L3-E20§

Fused Disconnect Selections

For Use With Time DelayFuses

194R-J400-1753

194R-J400-1753

194R-J600-1753

194R-J600-1753

194R-L800-1753 — — — — —

Bypass Contactor Reference‡�♦

AC-3 Rated per UL/CSA♠

Standard Fault SCCR

Short Circuit CurrentRatings @ 600V with: 100-D250* 100-D250* 100-D250* 100-D300* 100-D630* 100-D630* 100-D630* 100-D860* 100-D860* —

Standard Available Fault[kA] 18 30 42

Max. Non-Time DelayFuse 450 A 500 A 700 A 700 A 1000 A 1200 A 1600 A 1600 A 2000 A —

High Fault SCCR

Short Circuit CurrentRatings with: 100-D180* 100-D180* 100-D250* 100-D300* 100-D420* 100-D630* 100-D630* 100-D630* 100-D860* 100-G1200*

High Available Fault withFuses at 600V [kA] 65 65 42 42 65

Max. Class J or Class LTime Delay Fuse 225 A 225 A 350 A 450 A 500 A 600 A 700 A 800 A 1000 A 1300 A

‡ For complete catalog numbers, refer to the online catalog: www.ab.com/catalogs or the appropriate manufacturer's web site.�Always refer to local codes for proper selection of branch circuit components.∇ Circuit Breaker must be of the designated Bul. 140U Frame size for high fault short circuit ratings. Other circuit breakers pending.§ Requires rating plug selection based on application; refer to the online catalog: www.ab.com/catalogs♦ For most up to date information including voltage ratings other than 600V please see the Global SCCR Tables at www.rockwellautomation.com♠ In IEC regulated regions when sizing the bypass contactor per AC-1 or AC-3 ratings, the short circuit rating of the bypass contactor must be similar to the

SMC-50.

Bulletin 150




Specifications

Delta-Connected Motor Wiring Diagram using Bul. 825 Converter module and Cat. No. 150-SM2 Devices withBypass Contactor

Motor

SMC-50

T1/2 T2/4 T3/6

T1

T4

T2

T5

T3

T6

L1/1 L2/3 L3/5 AC-3 or AC-1 RatedBypass Contactor

SCR Fusing

Isolation Contactor (A)

825-MCMxx


L1 L2 L3

L1 L2 L3Delta Distribution Block

T6 T4 T5

Δ

§

‡ The 825-MCMxx provides current feedback to the SMC-50 when RUN in Bypass Operation. A Cat. No. 150-SM2 is also required. For30…180 A, use Cat. No. 825-MCM180; For 181…520A, use Cat. No. 825-MCM20 and user-supplied CTs with 5A secondary. ♣ Configuration not acceptable for emergency RUN off bypass.§Isolation contactor required.ΔBypass must be controlled by an auxiliary contact of the SMC-50 configured to exernal bypass.

Bulletin 150




Specifications

Delta-Connected Motor Wiring Diagram for Cat. No. 150-SC… and 150-SD… Devices with Bypass Contactorand Bypass Kit

Motor

SMC-50

T1/2 T2/4 T3/6

T1

T4

T2

T5

T3

T6

L1/1 L2/3 L3/5 AC-3 or AC-1 RatedBypass Contactor

SCR Fusing

Isolation Contactor (A)


L1 L2 L3

L1 L2 L3Delta Distribution Block

T6 T4 T5

Δ

§

‡ SMC-50 Bypass Bus Kit Cat. No. 150-SCBK or -SDBK is required.♣ Configuration not acceptable for emergency RUN off bypass.NOTE: Controller FRN 3.001or higher is required.§Isolation contactor required.ΔBypass must be controlled by an auxiliary contact of the SMC-50 configured to exernal bypass.

Bulletin 150




Approximate Dimensions

Cat. Nos. 150-SB1...SB4 Controllers without Terminal CoversDimensions are in inches (millimeters) unless otherwise noted. Dimensions are not intended for manufacturing purposes.

Cat. No. Weight

150-SB1

15.7 kg(34.6 lbs)

150-SB2

150-SB3

150-SB4

NOTE: When mounted in an enclosure, maintain a minimum of 6.0 inches (152.4 millimeters) clearance above or below the SMC-50. Side-to-side clearance is not required.

Minimum Enclosure Dimensions�

Cat. No. Type Width Height Depth

150-SB…Wye 609.6

(24.0)762.0(30.0)

304.8(12.0)

Inside-the-Delta

762.0(30.0)

965.2(38.0)

355.6(14.0)

150-SC… All 762.0(30.0)

965.2(38.0)

355.6(14.0)

150-SD… All 914.4(36.0)

1295.4(51.0)

355.6(14.0)

� Enclosure must be sized such that the enclosure's internal temperatureremains within specified controller ratings.

Minimum Enclosure Dimensions for Customer-Supplied Enclosures

0.19(4.8)

1.41(35.8)

7.25(184.2)

6.79(172.5)

10.21(259.2)

7.65(194.4)

6.69(170.0)

2.51(63.7)

2.51(63.7) Four Quantity

Ø 0.296 (7.51)

14.63(371.6)

6.25(158.8)

0.30(7.5)

1.07(27.1)

2.76(70.0)

13.39(340.0)

15.62(396.6)

13.95(354.4)

See detail A

Detail A#8-32 UNC 2B

0.79(20)

0.49(12.5)

0.41 dia(10.5)

1.25(31.8)

1.54(39.1)

Bulletin 150





Cat. Nos. 150-SB1...SB4 Controllers with Terminal CoversDimensions are in inches (millimeters) unless otherwise noted. Dimensions are not intended for manufacturing purposes.NOTE: When mounted in an enclosure, maintain a minimum of 6.0 inches (152.4 millimeters) clearance above or below the SMC-50. Side-to-side clearance is not required.

1.40(35.6)

1.54(39.0)9.22

(234.1)9.93

(252.3)

10.19(258.9)

6.98(177.4)

3.86(97.9)

7.62(193.7)

20.13(511.3)

Cat. No. Weight

150-SB1

15.9 kg(35.1 lbs)

150-SB2

150-SB3

150-SB4

Bulletin 150





Cat. Nos. 150-SC1...SC3 ControllersDimensions are in inches (millimeters) unless otherwise noted. Dimensions are not intended for manufacturing purposes.NOTE: When mounted in an enclosure, maintain a minimum of 6.0 inches (152.4 millimeters) clearance above or below the SMC-50. Side-to-side clearance is not required.

0.281 dia.

2.00(50.8)

10.75(272.9)

9.11(231.3)

0.25(6.4)

7.19(182.6)

0.67(17)

9.84 (250)

7.17 (182.1)

3.92 (99.6)

2.47(62.8)

9.30(236.2)

24.08(611.6)

23.25(590.6)

24.24(615.7) 25.14

(638.5)

2.09(53.1)

2.09(53.1)

5.34 (135.6)

7.66 (194.6)

9.84 (250)

10.75(273.1)

See detail A

Detail A

2.00(50.8)

1.16(29.5)

0.413 dia(10.49) 2 holes

0.53(13.5)

0.98(25)

Cat. No. Weight

150-SC147.6 kg(105 lb)

150-SC2

150-SC3

Bulletin 150





Dimensions are in inches (millimeters) unless otherwise noted. Dimensions are not intended for manufacturing purposes.NOTE: When mounted in an enclosure, maintain a minimum of 6.0 inches (152.4 millimeters) clearance above or below the SMC-50. Side-to-side clearance is not required.

26.84 (681.8)

1.44 (36.5)

8.23(209.2)

6.08 (154.4)

3.08(78.2)

27.23(691.6)

23.25(590.6)

3.15(80)

0.35(8.8)

1.02(26)

2.14(54.2)

1.44(36.5)

0.53(13.4)

26.17(664.6)

1.70(43.2)

Cat. No. Weight

150-SC147.6 kg(105 lb)

150-SC2

150-SC3

Cat. Nos. 150-SC1...SC3 Controllers with Lugs, Bypass Kit, and MOV Options

Bulletin 150





Cat. Nos. 150-SD1...SD3 ControllersDimensions are in inches (millimeters) unless otherwise noted. Dimensions are not intended for manufacturing purposes.NOTE: When mounted in an enclosure, maintain a minimum of 6.0 inches (152.4 millimeters) clearance above or below the SMC-50. Side-to-side clearance is not required.

Cat. No. Weight

150-SD177.1 kg(170 lb)

150-SD2

150-SD3

1.13 (28.7) dia. lifting holes (4)

1.31 (33.3)

0.39 (10) dia. mounting holes (4)

15.00 (381)

10.69(271.5)

5.05(128.3)

9.21(233.8)

15.00 (381)

0.400 dia.

25.88(657.3)

26.43(671.3)

25.25(641.4)

27.25(692.2)

3.156(80.16)

3.156(80.16)

7.844 (199.24)10.908 (277.06)

17.38 (441.5)18.00 (457.2)

8.63 (219.2)

11.64 (295.8)9.96 (253)

8.68 (220.5)

0.25 (6.4)2.04 (51.7)

See detail A

Detail A

3.00 (76.2)1.53

(38.9)

0.69 (17.5)

2.13(54)

0.53 dia.(13.5) 12 holes

Bulletin 150





Dimensions are in inches (millimeters) unless otherwise noted. Dimensions are not intended for manufacturing purposes.NOTE: When mounted in an enclosure, maintain a minimum of 6.0 inches (152.4 millimeters) clearance above or below the SMC-50. Side-to-side clearance is not required.

29.79 (756.8)

1.44 (36.5)

10.08 (256)

8.68 (220.5)

3.49(88.5)

28.58(726)

25.25(641.4)

1.82(46.2)

0.33(8.5)

1.54(39.2)

2.41(61.2)

Cat. No. Weight

150-SD177.1 kg(170 lb)

150-SD2

150-SD3

Cat. Nos. 150-SD1…SD3 Controllers with Lugs, Bypass Kit, and MOV Options

Bulletin 150





Enclosed-Type Line-Connected ControllersFactory-installed options may affect enclosure size requirements.Exact dimensions can be obtained after order entry. Please consult your local Rockwell Automation sales office or Allen-Bradley distributor.Dimensions are in millimeters (inches). Dimensions are not intended for manufacturing purposes.

A

B

D

E

F

C

Figure 1 — Wall-Mount

B

A

CLIFTING ANGLE

Figure 2 — Floor-Mount

Bulletin 150





ControllerRating [A] Bulletin

Input LineVoltageCode

WithOption

DimensionFigure No.

Dimensions in inches (mm)

A (Width) B (Height) C (Depth)D (Mtg.Dim.)

E (Mtg.Dim.)

F (Mtg.Dim.)

SMC-50 Combination Controller

B1152H, 153H

H,A,B,C — 1 30 (762) 38 (965) 14 (356) 0.75 (19) 36.5 (927) 28.5 (724)

H,A,B,C BP, NB 1 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

152B, 153B H,A,B,C — 1 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

B2 152H, 153H,152B, 153BH,A,B,C — 1 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

H,A,B,C BP, NB 1 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

B3 152H, 153H,152B, 153BH,A,B,C — 1 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

H,A,B,C BP, NB 1 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

B4 152H, 153H,152B, 153BH,A,B,C — 1 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

H,A,B,C BP, NB 1 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

C1

152HH,A,B,C — 1 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

H,A,B,C NB 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

153HH,A,B,C — 1 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

H,A,B,C NB 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

152B H,A,B,C — 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

H,A,B,C NB 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

153B H,A,B,C — 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

C2

152HH,A,B,C — 1 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

H,A,B,C NB 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

153HH,A,B,C — 1 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

H,A,B,C NB 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

152B H,A,B,C — 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

H,A,B,C NB 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

153B H,A,B,C — 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

C3

152HH,A,B,C — 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

H,A,B,C NB 2� 35 (889) 90 (2286) 20 (508) — — —

153HH,A,B,C — 1 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

H,A,B,C NB 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

152BH,A,B,C — 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

H,A,B,C NB 2� 35 (889) 90 (2286) 20 (508) — — —

153B H,A,B,C — 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

D1 152H, 153H,152B, 153B H,A,B,C — 2� 35 (889) 90 (2286) 20 (508) — — —

D2 152H, 153H,152B, 153B

H,A, B — 2� 35 (889) 90 (2286) 20 (508) — — —

C — 2� 35 (889) 90 (2286) 20 (508) — — —

C NB 2� 60 (1524) 90 (2286) 20 (508) — — —

D3 152H, 153H,152B, 153B

H,A — 2� 35 (889) 90 (2286) 20 (508) — — —

B, C — 2� 35 (889) 90 (2286) 20 (508) — — —

B, C NB 2� 60 (1524) 90 (2286) 20 (508) — — —

�The optional external mounting channels will add 1.5 inches to the height of an MCC section

Enclosed-Type Line-Connected Controllers

Bulletin 150





ControllerRating [A] Bulletin

Input LineVoltageCode

WithOption

DimensionFigure No.

Dimensions in inches (mm)

A (Width) B (Height) C (Depth)D (Mtg.Dim.)

E (Mtg.Dim.)

F (Mtg.Dim.)

SMC-50 Non-Combination Controller

B1150

H, A, B, C —

1

30 (762) 38 (965) 14 (356) 0.75 (19) 36.5 (927) 28.5 (724)

H, A, B, C NB 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

150B H, A, B, C — 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

B2150

H, A, B, C —

1

30 (762) 38 (965) 14 (356) 0.75 (19) 36.5 (927) 28.5 (724)

H, A, B, C NB 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

150B H, A, B, C — 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

B3150

H, A, B, C —

1

30 (762) 38 (965) 14 (356) 0.75 (19) 36.5 (927) 28.5 (724)

H, A, B, C NB 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

150B H, A, B, C — 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

B4150

H, A, B, C —

1

30 (762) 38 (965) 14 (356) 0.75 (19) 36.5 (927) 28.5 (724)

H, A, B, C NB 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

150B H, A, B, C — 36 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

C1150 H, A, B, C —

136 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

150B H, A, B, C — 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

C2150 H, A, B, C —

136 (914) 51 (1295) 14 (356) 0.75 (19) 49.5 (1257) 34.5 (876)

150B H, A, B, C — 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

C3150 H, A, B, C —

136 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

150B H, A, B, C — 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

D1

150 H, A, B, C — 1 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

150BH, A, B, C —

2�35 (889) 90 (2286) 20 (508) — — —

H, A, B, C NB 60 (1524) 90 (2286) 20 (508) — — —

D2

150

H, A, B —1

36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

C — 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

C NB

2�

60 (1524) 90 (2286) 20 (508) — — —

150BH, A, B, C — 35 (889) 90 (2286) 20 (508) — — —

H, A, B, C NB 60 (1524) 90 (2286) 20 (508) — — —

D3

150

H, A —1

36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

B, C — 36 (914) 60 (1524) 14 (356) 0.75 (19) 58.5 (1486) 34.5 (876)

B, C NB

2�

60 (1524) 90 (2286) 20 (508) — — —

150BH, A, B, C — 35 (889) 90 (2286) 20 (508) — — —

H, A, B, C NB 60 (1524) 90 (2286) 20 (508) — — —

�The optional external mounting channels will add 1.5 inches to the height of an MCC section

Enclosed-Type Line-Connected Controllers

Allen-Bradley, Rockwell Software, Rockwell Automation, and LISTEN. THINK. SOLVE are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Publication 150-SG010E-EN-P - March 2014Supercedes Publication 150-SG010D-EN-P - April 2013 Copyright © 2014 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.

smc-50 solid-state smart motor controller selection guide · 2017. 12. 6. · specifications........

Documents