smartplant 3d installation guide

of 117 /117
SmartPlant 3D Installation Guide September 2002 Version 3.0 DSP3D-PE-200019A

Author: luis-riquelme

Post on 29-Dec-2015

447 views

Category:

Documents


9 download

Embed Size (px)

TRANSCRIPT

  • SmartPlant 3D Installation Guide September 2002 Version 3.0

    DSP3D-PE-200019A

  • Copyright Copyright 2002 Intergraph Corporation All Rights Reserved

    Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license agreement; contains confidential and proprietary information of Intergraph and/or third parties which is protected by copyright and trade secret law and may not be provided or otherwise made available without proper authorization.

    Restricted Rights Legend Use, duplication, or disclosure by the government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of The Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 or subparagraphs (c) (1) and (2) of Commercial Computer Software---Restricted Rights at 48 CFR 52.227-19, as applicable.

    Unpublished---rights reserved under the copyright laws of the United States.

    Intergraph Corporation Huntsville, Alabama 35894-0001

    Warranties and Liabilities All warranties given by Intergraph Corporation about equipment or software are set forth in your purchase contract, and nothing stated in, or implied by, this document or its contents shall be considered or deemed a modification or amendment of such warranties. Intergraph believes the information in this publication is accurate as of its publication date.

    The information and the software discussed in this document are subject to change without notice and are subject to applicable technical product descriptions. Intergraph Corporation is not responsible for any error that may appear in this document.

    The software discussed in this document is furnished under a license and may be used or copied only in accordance with the terms of this license.

    No responsibility is assumed by Intergraph for the use or reliability of software on equipment that is not supplied by Intergraph or its affiliated companies. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINAL EVALUATION AS TO THE USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT.

    Trademarks Intergraph, the Intergraph logo, SmartSketch, FrameWorks, SmartPlant and INtools are registered trademarks and PDS and MARIAN are trademarks of Intergraph Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation. MicroStation is a registered trademark of Bentley Systems Inc. AutoCAD is a registered trademark of AutoDesk. Solid Edge is a trademark of Unigraphics Solutions, Inc. ISOGEN is a registered trademark of Alias Limited. Other brands and product names are trademarks of their respective owners.

  • Table of Contents

    SmartPlant 3D Installation Guide 3

    Table of Contents Preface ................................................................................................................................ 6

    Welcome to SmartPlant................................................................................................. 7

    Third-Party Integration.................................................................................................... 8

    Hardware and Software Requirements......................................................................... 10 Disk Partitioning Guidelines 10 Hardware Requirements 11 Software Requirements and Loading Order 13

    Installing SmartPlant 3D Workstation ......................................................................... 17 Prerequisite Software for SmartPlant 3D Workstation 18 Install and Verify Microsoft Windows 2000 Service Pack 2 19 Install and Verify Microsoft Internet Explorer 6.0 22 Install Microsoft Office 2000 24 Install Microsoft Data Access Components 2.6 Service Pack 1 25 Install Microsoft SQL Server 2000 Client Tools 26 Install SQL Server 2000 Service Pack 2: Database Components 27 Verify Startup of Microsoft Distributed Transaction Coordinator (MSDTC) 28 Install the Three-Button Mouse Driver 30 Verify a Workstation for SmartPlant 3D Installation 30 Install SmartPlant 3D Workstation 31

    Installing SmartPlant 3D Administrator ...................................................................... 36 Prerequisite Software for SmartPlant 3D Administrator 37 Install and Verify Microsoft Windows 2000 Service Pack 2 38 Install and Verify Microsoft Internet Explorer 6.0 41 Install Microsoft Office 2000 43 Install Microsoft SQL Server 2000 Client Tools 44 Install SQL Server 2000 Service Pack 2: Database Components 45 Verify Startup of Microsoft Distributed Transaction Coordinator (MSDTC) 46 Install the Three-Button Mouse Driver 47 Verify an Administrator System for SmartPlant 3D Installation 48 Install SmartPlant 3D Administrator 49

    Installing SmartPlant 3D SQL Server Data ................................................................. 53 Prerequisite Software for SmartPlant 3D SQL Server Data 53 Install and Verify Microsoft Windows 2000 Service Pack 2 54 Install and Verify Microsoft Internet Explorer 6.0 56 Install Microsoft SQL Server 2000 58

  • Table of Contents

    4 SmartPlant 3D Installation Guide

    Install SQL Server 2000 Service Pack 2: Database Components 60 Verify Automatic Startup of Microsoft SQL Server 2000 Services 61 Install SmartPlant 3D SQL Server Data 62 Install and Configure the COM+ Application on a Windows 2000 Server 65

    Install Optional Software for SmartPlant 3D............................................................... 72

    Configuring SmartPlant 3D Databases ......................................................................... 73 Register SQL Server 74 Create the Site, Catalog, and Schema Databases 78 Create the Plant Database 82 Create the Reports Database 84 Assign System Administrator Privileges 86

    Configuring Piping Manufacturing............................................................................... 90 Modify Default Isometric Paths 90 Bulk Load Database with Data 92

    Installing and Configuring VB Part Definition Wizard .............................................. 94 Install VB Part Definition Wizard 94

    Configuring Interference Checking Server .................................................................. 95 Set IFC Permission Requirements 95 Create IFC Permission Group Folder and Permission Group 96 Set IFC Permissions 97

    Starting the Interference Checking Server for Background Detection ..................... 99 Launch IFC Database Detect 99

    Getting Started with SmartPlant 3D ........................................................................... 102 Update Site Database Name and Path 102 Open SmartPlant 3D 103 Configure Your Tasks 103 Define Your Workspace 104 Save Session Files 105

    Remove SmartPlant 3D Software ................................................................................ 107 Register Solid Edge Version 10 .DLL File 108

    User Assistance .............................................................................................................. 109

    Customer Assistance ..................................................................................................... 112

    Common SmartPlant 3D Acronyms............................................................................ 113

  • Table of Contents

    SmartPlant 3D Installation Guide 5

    Index ............................................................................................................................... 115

  • Preface

    6 SmartPlant 3D Installation Guide

    Preface This document is an installation guide for SmartPlant 3D Administrator, SQL Server Data, and Workstation. The purpose of this document is to explain how to install and configure SmartPlant 3D for Microsoft Windows 2000 Professional and Microsoft 2000 Server, and all necessary prerequisite software. This document is delivered in .pdf format and requires Adobe Acrobat Reader to view. Adobe Acrobat Reader is delivered on the SmartPlant 3D Prerequisite CD.

    For information on SmartPlant 3D commands, refer to the SmartPlant 3D online Help.

    Note

    This document does not cover basic Windows 2000 Server, Windows 2000 Advanced Server, Windows 2000 Professional, or SQL Server 2000 operation. Refer to those products' printed documentation for basic operation information.

    You can find the most recent guides and online Help in the Help directory on the SmartPlant 3D product CD. Copy the updated files from the Help directory on the CD to the Common\Help directory on the workstation machines.

  • Welcome to SmartPlant

    SmartPlant 3D Installation Guide 7

    Welcome to SmartPlant The Intergraph Process, Power & Offshore SmartPlant family of process industry solutions is discipline-specific software that provides an integrated solution for the entire plant life cycle. SmartPlant provides knowledge-based, intuitive, easy-to-use, accessible, flexible, and data-driven tools that support global workflows. With SmartPlant, users can create information and provide data to multiple users at any moment. From these products, users are empowered to create logical and physical definitions of the plant model and have access to plant data from conceptual design through decommissioning.

    SmartPlant 3D: An Overview SmartPlant 3D uses Web and Windows technologies to provide a familiar interface for the user to produce step-changes in three-dimensional detailed plant design, procurement, construction, and operational system performance. This new data-centric solution approach generated by SmartPlant 3D synchronizes key elements of intragration and relationships.

    Intragration - SmartPlant 3D allows multiple engineering disciplines to work concurrently and in real-time against relational databases.

    Relationships - SmartPlant 3D's relationship manager controls design changes across disciplines, which in turn establishes and maintains appropriate behaviors among structures, equipment, and systems.

    SmartPlant 3D understands that plant design encompasses more than just 3-D modeling. As such, SmartPlant 3D is designed to integrate the SmartPlant Product Model with Enterprise Resource Planning (ERP), Operations and Maintenance (O&M), and Front End Engineering and Design (FEED). Traditionally, the only way to extract and load data from one application to another was through neutral format text files. SmartPlant 3D uses stress analysis, flow calculation, pump-sizing capability, and support selection point applications to perform these same tasks.

    Session files are used by SmartPlant 3D to empower users to define their own view of objects in the database. Its Project Management task enables users to administer and restrict user permissions to areas within the design catalog and the plant model. The optimistic locking feature in SmartPlant 3D makes it possible for users to work concurrently in the same environment and with the same component, whether it's specific to plant design or associated with the relationship of the components themselves. Additional features such as angle locking and interference checking make SmartPlant 3D the ideal software to manage system performance and maintain design intent.

    Related Topics Preface, page 6

  • Third-Party Integration

    8 SmartPlant 3D Installation Guide

    Third-Party Integration Equipment Modeling Capability Although an extensive library of symbols is delivered in the [Product Directory]\Catalog Data\Symbols folder on the administrator machine, you can customize additional three-dimensional symbols for your company using the Visual Basic Symbol Wizard or Solid Edge. Two-dimensional symbols for structural cross-sections are delivered in the CatalogData\Symbols\CrossSections folder. You can create your own two-dimensional cross-section symbols using the SmartPlant 2D Symbols application.

    The Visual Basic Symbol Wizard allows you to create and customize three-dimensional symbols that fit your company or project. The wizard produces a Visual Basic project for building the symbol ports and graphics, and generates an Excel workbook for bulkloading the symbol data into the Catalog database.

    SmartPlant 3D also integrates with Solid Edge to provide users with parametric modeling and assembly design capabilities. With Solid Edge, users can build intelligent equipment reference data libraries of base parts that can be placed into the SmartPlant 3D model. An entire catalog of standard equipment can be modeled with Solid Edge, as well as custom, one-of-a-kind equipment for specific plants. Solid Edge's design assistance automatically monitors how close the assemblies match design objectives and comply with design rules. Solid Edge and SmartPlant 3D use the same user interface paradigms, including SmartLocate, SmartStep, and QuickPick, making Solid Edge a natural addition to the SmartPlant 3D product suite. Optimal knowledge of Assembly is required to maximize this capability.

    You can create member cross-sections using the SmartPlant 2D Symbols application. This application allows you to define different representations for the cross-section using layers. You also can define variables to drive the dimensions of the cross-section symbol.

    For more information on SmartPlant 3D's equipment modeling capabilities, see either the SmartPlant 3D Reference Data Guide or the SmartPlant 2D Symbols User's Guide available from the Help > Printable Guides command in the software.

    Isometric Drawing Capability SmartPlant 3D's isometric drawing interface gives users the ability to create piping isometric drawings by extracting data from 3D models and fitting that data into software components. Additionally, the SmartPlant 3D isometric drawing interface works with ISOGEN software that not only enables users to create piping isometric drawings, including dimensioning, but that also allows users to generate notes, recognize attribute changes, and define which symbols to use in the final drawings. Knowledge of isometric drawings is required to effectively utilize this functionality.

  • Third-Party Integration

    SmartPlant 3D Installation Guide 9

    Related Topics Welcome to SmartPlant, page 7

  • Hardware and Software Requirements

    10 SmartPlant 3D Installation Guide

    Hardware and Software Requirements SmartPlant 3D is a state-of-the-art graphics application, capable of creating and displaying very complex three-dimensional models. The SmartPlant technology requires comparable state-of-the-art hardware to ensure a successful, productive, and efficient experience.

    Before continuing with the installation of SmartPlant 3D, confirm that the administrator, server and workstation machines meet the recommended guidelines for disk partitioning and meet both hardware and software requirements.

    Related Topics Hardware Requirements, page 11 Software Requirements and Loading Order, page 13

    Disk Partitioning Guidelines For best performance when loading and running SmartPlant 3D, partition the hard drive according to the following guidelines:

    1. Format all SmartPlant 3D partitions as NTFS file systems.

    By default, SmartPlant 3D is installed to C:\Program Files\SmartPlant\3D. Ensure you have sufficient free space on your C:\ partition (or another partition if you wish to install SmartPlant 3D there) according to the following information:

    Minimum Disk Space Requirements for SmartPlant 3D Prerequisite Software

    Windows 2000 Service Pack 2 Varies. Refer to the READMESP.HTM file delivered with Service Pack

    Internet Explorer 6.0 12 MB

    Microsoft Office 2000 Varies. Refer to MS Office documentation.

    Microsoft Data Access Components 2.6 Service Pack 1

    20 MB

    Microsoft SQL Server 2000 270 MB

    Microsoft 2000 Client Tools 153 MB

    Microsoft SQL Server 2000 Service Pack 2: Database Components

    147 MB

    3-Button Mouse Driver 4 MB

  • Hardware and Software Requirements

    SmartPlant 3D Installation Guide 11

    Minimum Disk Space Requirements for SmartPlant 3D by Setup

    SmartPlant 3D Workstation 519 MB

    SmartPlant 3D Workstation with Project Management option

    530 MB

    SmartPlant 3D Administrator 484 MB

    SmartPlant 3D Server Data 112 MB

    2. Ensure that the partition where the SQL Server data files will be stored has sufficient space. The system requires 120 MB to create a new set of databases and a small model will take a minimum of 250-300 MB. Intergraph PPO recommends that you have at least 1.0 GB of free space for database storage.

    You also will need additional disk space if you intend to use other products, such as Visual Basic 6.0 with Visual Studio Service Pack 5, and/or Solid Edge version 10. Please consult your system administrator for this and additional software not provided by Intergraph PPO.

    Warning

    Do not continue with the installation of SmartPlant 3D until enough disk space is free on the workstation, administrator, or server machine as stated in the aforementioned procedure.

    Related Topics Disk Partitioning Guidelines, page 10

    Hardware Requirements For optimal viewing and performance results of SmartPlant 3D, the following minimum hardware requirements are advised:

    500 MHz Pentium II processor, or higher, recommended

    Minimum of 256 MB memory for each client

    Minimum of 512 MB memory for server

    100Mbit or better network with 100Mbit or better NICs in each machine

    Minimum of 1 GB hard drive disk space on the drive where the SQL server databases are stored

    Access to a CD-ROM drive or network drive

    21" color monitor (capable of a minimum of 1024 x 768)

  • Hardware and Software Requirements

    12 SmartPlant 3D Installation Guide

    Graphics cards designed for 3D intensive applications that generate low CPU overhead and meet the following requirements:

    32-bit main RGBA pixel buffer

    Hardware OpenGL 1.1 support

    Hardware Z buffer: 32 bit

    64 MB RAM recommended, 32 MB RAM minimum

    4-bit minimum overlay buffer support

    8-bit stencil buffer

    Hardware Alpha blending support

    Hardware Anti-aliasing support recommended

    Important

    If you are unsure about your graphics card's capabilities, contact your vendor or local system support group for assistance.

    Notes

    Many of the recent generation video cards provide some level of OpenGL acceleration. Some manufacturers provide poor OpenGL drivers that can cause artifacts. Testing has shown that NVIDIA and Intense3D provide good drivers. ATI and Matrox often seem to have OpenGL problems with their drivers. Cards with double-buffered overlay planes (such as the Wildcat cards) have an advantage because highlighting can be done without having to do save/restores. Cards without overlay planes rely on blits during highlight operations, so good blit performance is needed, as well as good drivers. For example, the NVIDIA Geforce 2 graphics cards had unacceptable performance with their initial drivers, but since the release of the Detonator 3 drivers and beyond, the Geforce 2 cards have shown good performance while running SmartPlant 3D.

    Dual screen configurations should have either a single graphics card with two VGA outputs or two identical graphics cards. The graphics card(s) should otherwise meet the requirements of the specified graphics card recommendations.

    Related Topics Hardware and Software Requirements, page 10

  • Hardware and Software Requirements

    SmartPlant 3D Installation Guide 13

    Software Requirements and Loading Order Software Requirements For optimal performance, Intergraph PPO recommends installing SmartPlant 3D on systems running on a Windows 2000 platform. To aid in product installation, SmartPlant 3D comes with two CDs:

    The Intergraph SmartPlant 3D Prerequisite CD includes essential software for the successful operation of SmartPlant 3D.

    The Intergraph SmartPlant 3D Product CD includes SmartPlant 3D administrator, server, and workstation installation software.

    Important

    The Intergraph SmartPlant 3D Prerequisite CD contains only software that Intergraph PPO is free to distribute. Contact the appropriate vendors for other software required, such as Microsoft Windows 2000 or Microsoft Office 2000.

    The following table outlines the prerequisites associated with each of the three SmartPlant 3D installations and the established load order for each:

    Server Installation

    Administrator Installation

    Workstation Installation Version

    Windows 2000 Server or Advanced Server

    Windows 2000 Professional

    Windows 2000 Professional

    1Windows 2000 Service Pack 2 (SP2)

    1Windows 2000 SP2

    1Windows 2000 SP2 Build 2195

    1Internet Explorer 6.0

    1Internet Explorer 6.0

    1Internet Explorer 6.0 6.0.2600.0000

    Microsoft Office 2000

    Microsoft Office 2000

    Microsoft Data Access Components (MDAC) 2.6 Service Pack 1 (SP1)

    SQL Server 2000 SQL Server 2000 Client Tools

    2SQL Server 2000 Client Tools

  • Hardware and Software Requirements

    14 SmartPlant 3D Installation Guide

    Server Installation Administrator Installation

    Workstation Installation

    Version

    SQL Server 2000 Service Pack 2 (SP2): Database Components

    SQL Server 2000 SP2: Database Components

    2SQL Server 2000 SP2: Database Components

    8.00.534

    13-Button Mouse Driver

    13-Button Mouse Driver

    Logitech Mouseware 9.1

    1Denotes items provided by Intergraph PPO on the Intergraph SmartPlant 3D Prerequisite CD. 2Microsoft SQL Server 2000 Client tools and SQL Server 2000 SP2 are only required for the Workstation installation if the Project Management option is installed; otherwise, they are not integral to the default Workstation installation.

    Important

    SmartPlant 3D guidelines require that you load your workstation, administrator, or server with the specific versions of software listed above. Earlier or later versions may not work. Do not proceed with the SmartPlant 3D installation if the versions of the products installed on the system do not match versions specified in the previous table. If it is necessary to regress or update a software component to match the above versions, contact your system support personnel.

    Software Loading Order The ability to run SmartPlant 3D successfully is greatly affected by the order in which all the necessary and underlying products are loaded. Do not deviate from the recommended order. Doing so can result in a component that is out-of-sync with the guidelines; consequently, it will be difficult to determine the exact nature of any post-installation problems you encounter should you deviate from the recommended installation order.

    The following software packages are required for SmartPlant 3D to run optimally:

    1. Microsoft Windows 2000 Server, Advanced Server or Professional 2. Microsoft Windows 2000 SP2 3. Microsoft Internet Explorer 6.0 4. Microsoft Office 2000 5. Microsoft Data Access Components (MDAC) 2.6 SP1, Microsoft SQL Server

    2000, and/ or Microsoft SQL Server 2000 Client Tools

  • Hardware and Software Requirements

    SmartPlant 3D Installation Guide 15

    6. Microsoft SQL Server 2000 SP2: Database Components 7. Drivers for middle mouse button 8. Intergraph SmartPlant 3D Workstation, Administrator, or Server

    Other users who want to perform different tasks in the overall plant design workflow might need additional software, such as Microsoft Visual Basic and Unigraphics Solid Edge Version 10. You may install these packages on individual machines after SmarPlant 3D and its prerequisite software have been installed successfully.

    Important

    Do not skip any restarts recommended by the system. Doing so can have unintended consequences.

    SmartPlant 3D Installations Three installation options exist for SmartPlant 3D:

    SmartPlant 3D Workstation

    SmartPlant 3D Administrator

    SmartPlant 3D SQL Server Data.

    Only specific configurations can exist simultaneously on the same machine, as outlined in the following table:

    SmartPlant 3D Workstation

    (with or without the Project

    Management Option)

    SmartPlant 3D Administrator

    SmartPlant 3D SQL Server Data

    SmartPlant 3D Workstation N/A No Yes

    SmartPlant 3D Administrator No N/A Yes

    SmartPlant 3D SQL Server Data Yes Yes N/A

    Note

    If you wish to have the functionality of both the Administrator and Workstation builds on the same machine, you should install SmartPlant 3D Workstation and include the Project Management option as part of the installation select set.

  • Hardware and Software Requirements

    16 SmartPlant 3D Installation Guide

    Related Topics Hardware and Software Requirements, page 10

  • Installing SmartPlant 3D Workstation

    SmartPlant 3D Installation Guide 17

    Installing SmartPlant 3D Workstation The SmartPlant 3D Workstation software is intended for general SmartPlant 3D modeling and should not be used for building a SmartPlant 3D administrator machine - the SmartPlant 3D Administrator software should be used for that purpose. You can, however, get all the capabilities of the Administrator software by selecting the optional Project Management component during the while installing the Workstation software. The following table summarizes the differences between the Workstation and Administrator software:

    Task, Utility and/or Application Name Workstation Administrator

    SmartPlant 3D with the following tasks:

    Cableway X X

    Catalog X X

    Common X X

    Drawings X X

    Equipment & Furnishings X

    Grids X

    Hangers & Supports X

    HVAC X

    Piping X

    Piping Manufacturing X

    Reports X

    Space Management X

    Structure X

    Systems and Specifications X

    2D Symbols X X

  • Installing SmartPlant 3D Workstation

    18 SmartPlant 3D Installation Guide

    Task, Utility and/or Application Name Workstation Administrator

    Project Management Optional1 X

    Database Wizard 1,2 X

    Bulkload Reference Data 1,2 X

    Check Interference Tool 1 X 1If you choose to install Project Management as an optional part of the Workstation software, the Database Wizard, Bulkload Reference Data, and Check Interference components are also installed. 2For the Database Wizard and Bulkload Reference Data components to function correctly, SQL Server 2000 Client Tools and SQL Server 2000 SP2 must be installed on the same machine.

    Important

    SmartPlant 3D Workstation and Administrator software should not be installed on the same system. If you want to use the many tasks contained in the Workstation software, as well as the functionalities included in the Administrator software, you should only install the Workstation software and include the optional Project Management component; otherwise, install only the default components of the Workstation software.

    This section describes how to install Intergraph SmartPlant 3D and its prerequisite software on a computer running the Microsoft Windows 2000 Professional operating system. Before beginning the installation process, verify that the workstation meets the specifications described in Hardware Requirements, page 11 and Software Requirements and Loading Order, page 13.

    Related Topics Install SmartPlant 3D Workstation, page 31

    Prerequisite Software for SmartPlant 3D Workstation

    Prior to loading SmartPlant 3D on a workstation machine running on a Windows 2000 platform, you must verify that the following prerequisite software is installed:

    Microsoft Windows 2000 Professional SP2

    Microsoft Internet Explorer 6.0 Microsoft Office 2000

  • Installing SmartPlant 3D Workstation

    SmartPlant 3D Installation Guide 19

    Microsoft Data Access Components (MDAC) 2.6 SP1 or Microsoft SQL Server 2000 Client Tools (includes MDAC 2.6 SP2 and is required only when the Project Management option is installed)

    Microsoft SQL Server 2000 SP2: Database Components (required only when the Project Management option is installed)

    Three-Button Mouse Driver

    The following sections provide step-by-step guidelines for verifying and/or installing prerequisite software.

    Important

    Before beginning the installation process, verify that the workstation meets the specifications described in Hardware Requirements, page 11.

    For optimal performance, Intergraph PPO recommends installing SmartPlant 3D on systems running on a Windows 2000 platform. You must have all SmartPlant 3D prerequisites installed in order to run the SmartPlant 3D Workstation setup. For more information regarding software specifications, see Software Requirements and Loading Order, page 13.

    You must have administrative privileges on the workstation machine to start the installation. See the online Help for Microsoft Windows 2000 for instructions on how to establish administrative privileges.

    The SmartPlant 3D Workstation and Administrator setups should not be installed on the same system.

    Related Topics Installing SmartPlant 3D Workstation, page 17

    Install and Verify Microsoft Windows 2000 Service Pack 2

    Ensure that Microsoft Windows 2000 Professional and Microsoft Windows 2000 SP2 are installed.

    Verify Microsoft Windows 2000 SP2 1. Click Start > Run. 2. Type winver in the Open text box. 3. Click OK. 4. The About Windows dialog box appears. Verify that Microsoft Windows 2000

    and Microsoft Windows 2000 SP2 are installed. If the information matches the graphic, proceed to Install and Verify Microsoft Internet Explorer 6.0, page 22. If

  • Installing SmartPlant 3D Workstation

    20 SmartPlant 3D Installation Guide

    the information does not match the picture, perform the steps in the next section to install SP2.

    5. Click OK to close the About Windows dialog box.

    Install Microsoft Windows 2000 Service Pack 2 1. Insert the Intergraph SmartPlant 3D Prerequisite CD.

    Tip

    If the CD does not start automatically, double-click Setup.exe in the root directory of the CD.

    2. On the SmartPlant 3D Prerequisite Software Installation dialog box, click Workstation Prerequisites.

  • Installing SmartPlant 3D Workstation

    SmartPlant 3D Installation Guide 21

    3. Select Microsoft Windows 2000 Service Pack 2. 4. Click to accept the license agreement. 5. Click Install.

    Important

    If a dialog box appears with the following message: Warning: You have chosen to overwrite our existing uninstall of Service Pack 1. Are you sure you want to Continue?, click Yes.

    6. Click Restart on the Windows 2000 Service Pack Setup dialog box when prompted.

    7. Log on to Microsoft Windows 2000. 8. Click Start > Run. 9. Type winver in the Open text box. 10. Verify that Windows 2000 SP2 is installed. 11. Click OK to close the About Windows dialog box.

  • Installing SmartPlant 3D Workstation

    22 SmartPlant 3D Installation Guide

    Related Topics Installing SmartPlant 3D Administrator, page 36 Installing SmartPlant 3D Workstation, page 17

    Install and Verify Microsoft Internet Explorer 6.0 After verifying that the appropriate operating system and service pack software are installed on the workstation, install Microsoft Internet Explorer 6.0 on to the Microsoft Windows 2000 Professional workstation.

    Tip

    If the operating system does not have an existing Internet connection method, the Internet Connection Wizard appears. Consult your system administrator to establish a connection.

    Verify Microsoft Internet Explorer 6.0 If you have Internet Explorer already installed, verify the version installed by following these steps.

    1. Verify the version of Internet Explorer installed on the workstation by launching Internet Explorer.

    2. Click Help > About Internet Explorer.

    Note

    If Internet Explorer 6.0 is already installed, the version number displays in the About Internet Explorer dialog box as Version 6.0.2600.0000.

  • Installing SmartPlant 3D Workstation

    SmartPlant 3D Installation Guide 23

    3. If the version is not correct, follow the steps in the next section to install Internet

    Explorer 6.0.

    Install Microsoft Internet Explorer 6.0 1. On the SmartPlant 3D Prerequisite Software Installation window, click

    Workstation Prerequisites. 2. Select Microsoft Internet Explorer 6.0. 3. Click I accept the agreement. 4. Click Next. 5. Click Next. 6. Click Finish to exit Internet Explorer setup and to restart your computer. 7. Log on to Microsoft Windows 2000 Professional. 8. Wait as the different services are configured on the workstation. 9. Launch Internet Explorer. 10. Click Help > About Internet Explorer.

  • Installing SmartPlant 3D Workstation

    24 SmartPlant 3D Installation Guide

    Tip

    The About Internet Explorer dialog box should display Version 6.0.2600.0000.

    11. Click OK to close the About Internet Explorer dialog box.

    Related Topics Installing SmartPlant 3D Workstation, page 17

    Install Microsoft Office 2000 Several of the SmartPlant 3D tasks require Microsoft Office 2000. SmartPlant 3D designers need Excel to create reports and system administrators rely on Excel to make changes to the reference data spreadsheets and bulk load them into the Catalog database. For more information, see the SmartPlant 3D Reference Data User's Guide, available from the Help>Printable Guides command in the software.

    Important

    Approximately 310 MB of hard disk space is required to load Office 2000 Standard Edition.

    1. Insert the Microsoft Office 2000 CD. 2. Double-click Setup.exe. 3. Enter the appropriate User name, Initials, and Organization information. 4. Click Next on the Welcome to Microsoft Office 2000 page. 5. Click I accept the terms in the License Agreement to accept the License

    Agreement. 6. Click Next. 7. Click Customize. 8. Select the installation location. 9. Click Next. 10. Expand the hierarchy for Microsoft Office.

  • Installing SmartPlant 3D Workstation

    SmartPlant 3D Installation Guide 25

    11. Select Run all from My Computer. 12. Click Install Now.

    Related Topics Installing SmartPlant 3D Administrator, page 36 Installing SmartPlant 3D Workstation, page 17

    Install Microsoft Data Access Components 2.6 Service Pack 1

    After installing Microsoft Windows 2000 Professional, Microsoft Windows 2000 SP2, Microsoft Internet Explorer 6.0 and Microsoft Office 2000 on the workstation, you can now install MDAC 2.6 SP1.

    Important

    If you intend to include the Project Management software as part of the workstation setup, skip this procedure and move on to Install Microsoft SQL Server 2000 Client Tools, page 26. MDAC 2.6 Service Pack 2 (SP2) is automatically installed on the system with SQL Server 2000 Client Tools.

  • Installing SmartPlant 3D Workstation

    26 SmartPlant 3D Installation Guide

    1. On the SmartPlant 3D Prerequisite Software Installation dialog box, click Workstation Prerequisites.

    2. Select Microsoft Data Access Components 2.6 Service Pack 1. 3. Select I accept all of the terms of the preceding license agreement. 4. Click Next. 5. Click Finish to begin installation of MDAC 2.6 SP1. 6. If given the option, select Let setup restart the system now. 7. Click Close.

    Related Topics Installing SmartPlant 3D Workstation, page 17

    Install Microsoft SQL Server 2000 Client Tools After installing Microsoft Windows 2000 Professional, Microsoft Windows 2000 SP2, Microsoft Internet Explorer 6.0 and Microsoft Office 2000 on the workstation, you can now install Microsoft SQL Server 2000 Client Tools. During installation of Client Tools, MDAC 2.6 (SP2) is installed.

    Important

    Installation of Microsoft SQL Server 2000 Client Tools is optional for a workstation. If you are installing the SmartPlant 3D Project Management software on your local workstation, you must also install SQL Server 2000 Client Tools. If you do not plan to run the Project Management task from the workstation and previously installed MDAC 2.6 SP1 as outlined in Install Microsoft Data Access Components 2.6 Service Pack 1, page 25, skip to Verify Automatic Startup of Microsoft Data Transaction Coordinator, page 28 to continue with the SmartPlant 3D Workstation setup process.

    Warning

    SQL Server 2000 is a separately licensed Microsoft product. Make sure you have a valid license for Microsoft SQL Server 2000 Client Tools software

    Install Microsoft SQL Server 2000 Client Tools 1. Insert the Microsoft SQL Server 2000 CD.

    Tip

    If the compact disc does not autorun, double-click Autorun.exe in the root directory of the compact disc.

    2. On the Microsoft SQL Server Installation page, click SQL Server 2000 Components.

  • Installing SmartPlant 3D Workstation

    SmartPlant 3D Installation Guide 27

    3. Click Install Database Server. 4. On the Setup Warning page, click OK. 5. On the Welcome page, click Next. 6. On the Computer Name page, click Next. 7. On the Installation Selection page, select Create a new instance of SQL

    Server, or install Client Tools, and then click Next. 8. Follow the directions on the User Information, Software License Agreement,

    and related pages. 9. On the Installation Definition page, select Client Tools Only, and then click

    Next. 10. On the Select Components page, accept the defaults, and then click Next.

    Tip

    Approximately 208KB of free space is initially required. In addition, a typical installation requires approximately 151MB of space on the system drive, regardless of the location of the program or data files.

    11. On the Start Copying Files page, click Next.

    Tip

    The status bar displays the progress as the SQL Server 2000 files are copied to the workstation. Once the files are installed, the installation script will take a few minutes to start or stop some services, register components, and perform other configuration tasks.

    12. Click Finish on the Setup Complete page. The SQL Server 2000 installation is complete.

    Related Topics Installing SmartPlant 3D Workstation, page 17

    Install SQL Server 2000 Service Pack 2: Database Components

    After installing Microsoft SQL Server 2000 Client Tools on the workstation, you can now install SQL Server 2000 SP2: Database Components.

    Important

    Installation of Microsoft SQL Server 2000 Client Tools and SQL Server 2000 SP2 is optional for a workstation. If you are installing the SmartPlant 3D Project Management software on your local workstation, you must install SQL Server 2000 Client Tools and SP2. If you are not planning to run the Project Management task from the workstation, skip

  • Installing SmartPlant 3D Workstation

    28 SmartPlant 3D Installation Guide

    to Verify Automatic Startup of Microsoft Distributed Transaction Coordinator (MSDTC), page 28.

    Warning

    Microsoft SQL Server 2000 Client Tools must be installed on the workstation prior to installing SQL Server 2000 SP2. If you have not installed Microsoft SQL Server 2000 Client tools, refer to Install Microsoft SQL Server 2000 Client Tools, page 26 before proceeding.

    Install SQL Server 2000 SP2 1. Insert the SmartPlant 3D Prerequisite CD.

    Tip

    If the CD does not start automatically, double-click Setup.exe in the root directory of the CD.

    2. On the SmartPlant 3D Prerequisite Software Installation window, click Administrator Prerequisites or Server Prerequisites.

    3. Select Microsoft SQL Server 2000 Service Pack 2. 4. On the Welcome page, click Next. 5. On the Software License Agreement page, click Yes. 6. On the Start Copying Files page, click Next.

    Tip

    The status bar displays the progress as the component files are copied to the workstation. Once the files are installed, the installation script will take a few minutes to start or stop some services, register components, and perform other configuration tasks.

    7. Click Finish on the Setup Complete page. The SQL Server 2000 SP2 installation is complete.

    Related Topics Installing SmartPlant 3D Workstation, page 17

    Verify Startup of Microsoft Distributed Transaction Coordinator (MSDTC)

    Verify MSDTC is Started 1. Click Start > Settings > Control Panel > Administrative Tools, and double-

    click Services.

  • Installing SmartPlant 3D Workstation

    SmartPlant 3D Installation Guide 29

    Tip

    You can also right-click My Computer and select Manage. In the Computer Management window, expand the Services and Applications node and click Services.

    2. Locate Distributed Transaction Coordinator in the list of services, and verify that the Status is set to Started and Startup Type is set to Automatic.

    3. If the Distributed Transaction Coordinator service is not started, follow the steps

    in the next section to start the service; otherwise, proceed to Install the Three-Button Mouse Driver, page 30.

    Start MSDTC 1. If the Services window is not open, click Start > Settings > Control Panel >

    Administrative Tools, and double-click Services. 2. To change the Status or Startup Type, right-click on the Distributed

    Transaction Coordinator service, and select Properties from the shortcut menu. 3. On the General tab, select Automatic from the Startup type list. 4. In the Service status section, click Start. 5. Click OK.

    Related Topics Installing SmartPlant 3D Workstation, page 17

  • Installing SmartPlant 3D Workstation

    30 SmartPlant 3D Installation Guide

    Install the Three-Button Mouse Driver The following steps to install the three-button mouse driver should be performed to ensure correct SmartPlant 3D middle-mouse button functions.

    1. From the root directory of the Intergraph SmartPlant 3D Prerequisite CD, navigate to 3_Button_Mouse_Driver\lmouse_Driver.

    2. Double-click Setup.exe. 3. Select English from the list on the Choose Setup Language dialog box, and then

    click OK. 4. On the Choose Destination Location page, click Next to accept the default

    location.

    Tip

    To select an alternative destination location, click Browse and navigate to the desired location.

    5. On the Select Program Folder page, click Next to accept the default. The required files are installed on the machine.

    6. Click Finish. The system will automatically restart to configure the new files. 7. Log back onto the machine. 8. Click Yes on the New Device message box. The Device Setup Wizard starts. 9. Click Next. 10. Select the side on which the mouse will be positioned, and click Next. 11. In the Other: list, select Middle Button, and then click Next. 12. Check the Make Double-Clicking Easier option, if desired, and then click Next. 13. Click Finish. 14. Click OK on the Mouse Properties dialog box.

    Related Topics Installing SmartPlant 3D Workstation, page 17

    Verify a Workstation for SmartPlant 3D Installation

    Important

    Approximately 519 MB of hard disk space is required to load SmartPlant 3D Workstation. Prior to installing SmartPlant 3D Workstation, select and size the workstation's hard disk partitions accordingly. For additional information, see Disk Partitioning Guidelines, page 10.

  • Installing SmartPlant 3D Workstation

    SmartPlant 3D Installation Guide 31

    SmartPlant 3D version 3.0 has not been certified with other Intergraph PPO software installed on the same system. It is not recommended to install other Intergraph PPO software with the SmartPlant 3D application.

    If it is necessary to install both SmartSketch and SmartPlant 3D version 3.0 on the same system, it is recommended to install SmartSketch before installing the SmartPlant 3D application.

    If you intend to use Unigraphics Solid Edge Version 10 on a workstation machine, you must install it prior to running the SmartPlant 3D Workstation setup.

    Caution

    The selected disk partition must be formatted using an NTFS (not FAT 16/32) file system. Verify the file system for the desired partition using Disk Management under Microsoft Windows 2000 Administrative Tools. If the partition is formatted with a FAT 16/32 file system, contact your system administrator to have it converted to a NTFS before commencing the SmartPlant 3D installation.

    1. Click Start > Settings > Control Panel. 2. Double-click Administrative Tools, and then double-click Computer

    Management. 3. In the console tree under Storage, click Disk Management. 4. Select the disk partition on which you want to install SmartPlant 3D. 5. Right-click the disk partition and select Properties on the shortcut menu. 6. Verify that 519 MB or greater free hard drive space is available on the partition in

    which you plan to install SmartPlant 3D Workstation.

    Prerequisite Software Ensure the proper SmartPlant 3D prerequisite software has been installed on the workstation according to the instructions outlined in Software Requirements and Loading Order, page 13.

    Related Topics Installing SmartPlant 3D Workstation, page 17

    Install SmartPlant 3D Workstation Important

    Prior to installing SmartPlant 3D on a workstation, verify that all prerequisite software has been installed. For more information, refer to Prerequisite Software for SmartPlant 3D Workstation, page 18.

  • Installing SmartPlant 3D Workstation

    32 SmartPlant 3D Installation Guide

    If you have an older version of SmartPlant 3D Workstation installed on your machine, uninstall it before loading the new software. Refer to the section entitled Remove SmartPlant 3D Software, page 107.

    You must have administrator privileges on the workstation to install the software.

    1. Insert the Intergraph SmartPlant 3D Product CD.

    Tip

    If the CD does not start automatically, double-click Setup.exe in the root directory of the CD.

    2. Select SmartPlant 3D Workstation Installation. 3. Click Next on the SmartPlant 3D Workstation Setup page. 4. On the License Agreement page, select I accept the license agreement, and then

    click Next. 5. Click Next on the Readme Information page. 6. On the User Information page, enter information in the Full Name and

    Organization boxes. 7. Click Next. 8. On the Select Features page select the SmartPlant 3D product features that you

    want installed.

    Important

    If you want to be able to create databases with the workstation setup, scroll to the bottom of the Select Features list, and highlight the Project Management option.

    Tip

    If the default configuration options meet your needs, you can skip steps 9 and 10.

    9. Click Browse and select the directory location for SmartPlant 3D, and then click OK.

  • Installing SmartPlant 3D Workstation

    SmartPlant 3D Installation Guide 33

    10. Click Next. 11. Click Next on the Ready to Install the Application page to begin installing

    SmartPlant 3D Workstation.

  • Installing SmartPlant 3D Workstation

    34 SmartPlant 3D Installation Guide

    12. After SmartPlant 3D Workstation is loaded, the following page appears:

    13. Click Finish to exit the SmartPlant 3D Workstation installation sequence.

  • Installing SmartPlant 3D Workstation

    SmartPlant 3D Installation Guide 35

    Important

    Restart the computer to complete the installation.

    Related Topics Installing SmartPlant 3D Workstation, page 17

  • Installing SmartPlant 3D Administrator

    36 SmartPlant 3D Installation Guide

    Installing SmartPlant 3D Administrator The SmartPlant 3D Administrator software is intended for creating and managing SmartPlant 3D databases and is not intended to be used for building a SmartPlant 3D general modeling workstation. The SmartPlant 3D Workstation software should be used for that purpose. Installing the Administrator software installs a limited set of SmartPlant 3D tasks on the machine along with some additional applications/utilities not installed by a default Workstation installation. The following table summarizes the differences between the Administration and Workstation software:

    Task, Utility and/or Application Name Workstation Administrator

    SmartPlant 3D with the following tasks:

    Cableway X X

    Catalog X X

    Common X X

    Drawings X X

    Equipment & Furnishings X

    Grids X

    Hangers & Supports X

    HVAC X

    Piping X

    Piping Manufacturing X

    Reports X

    Space Management X

    Structure X

    Systems and Specifications X

    2D Symbols X X

  • Installing SmartPlant 3D Administrator

    SmartPlant 3D Installation Guide 37

    Task, Utility and/or Application Name Workstation Administrator

    Project Management Optional1 X

    Database Wizard 1,2 X

    Bulkload Reference Data 1,2 X

    Check Interference Tool 1 X 1If you choose to install Project Management as an optional part of the Workstation software, the Database Wizard, Bulkload Reference Data, and Check Interference components are also installed. 2For the Database Wizard and Bulkload Reference Data components to function correctly, SQL Server 2000 Client Tools and SQL Server 2000 SP2 must be installed on the same machine.

    Important

    SmartPlant 3D Administrator and Workstation software should not be installed on the same system. If you want to use the functionalities of the Administrator software and the additional tasks included in the Workstation software, you should only install the Workstation software and include the optional Project Management component; otherwise, only install the Administrator software.

    This section describes how to install Intergraph SmartPlant 3D and its prerequisite software on an administrator machine running the Microsoft Windows 2000 Professional operating system. Before beginning the installation process, verify that the system meets the specifications described in Hardware Requirements, page 11 and Software Requirements and Loading Order, page 13.

    Related Topics Install SmartPlant 3D Administrator, page 49 Prerequisite Software for SmartPlant 3D Administrator, page 37

    Prerequisite Software for SmartPlant 3D Administrator

    Prior to loading SmartPlant 3D on an administrator machine running on a Windows 2000 platform, you must verify that the following prerequisite software is installed:

    Microsoft Windows Professional SP2 Microsoft Internet Explorer 6.0

    Microsoft Office 2000

  • Installing SmartPlant 3D Administrator

    38 SmartPlant 3D Installation Guide

    Microsoft SQL Server 2000 Client Tools

    Microsoft SQL Server 2000 SP2: Database Components

    Three-Button Mouse Driver

    The following sections provide step-by-step guidelines for verifying and/or installing prerequisite software.

    Important

    Before beginning the installation process, verify that the administrator machine meets the specifications described in Hardware Requirements, page 11.

    For optimal performance, Intergraph PPO recommends installing SmartPlant 3D on systems running on a Windows 2000 platform. You must have all SmartPlant 3D prerequisites installed in order to run the SmartPlant 3D Administrator setup. For more information regarding software specifications, see Software Requirements and Loading Order, page 13.

    You must have administrative privileges on the administrator machine to start the installation. See the online Help for Microsoft Windows 2000 for instructions on how to establish administrative privileges.

    The SmartPlant 3D Administrator and Workstation setups should not be installed on the same system.

    Related Topics Installing SmartPlant 3D Administrator, page 36

    Install and Verify Microsoft Windows 2000 Service Pack 2

    Ensure that Microsoft Windows 2000 Professional and Microsoft Windows 2000 SP2 are installed.

    Verify Microsoft Windows 2000 SP2 1. Click Start > Run. 2. Type winver in the Open text box. 3. Click OK. 4. The About Windows dialog box appears. Verify that Microsoft Windows 2000

    and Microsoft Windows 2000 SP2 are installed. If the information matches the graphic, proceed to Install and Verify Microsoft Internet Explorer 6.0, page 22. If the information does not match the picture, perform the steps in the next section to install SP2.

  • Installing SmartPlant 3D Administrator

    SmartPlant 3D Installation Guide 39

    5. Click OK to close the About Windows dialog box.

    Install Microsoft Windows 2000 Service Pack 2 1. Insert the Intergraph SmartPlant 3D Prerequisite CD.

    Tip

    If the CD does not start automatically, double-click Setup.exe in the root directory of the CD.

    2. On the SmartPlant 3D Prerequisite Software Installation dialog box, click Administrator Prerequisites.

  • Installing SmartPlant 3D Administrator

    40 SmartPlant 3D Installation Guide

    3. Select Microsoft Windows 2000 Service Pack 2. 4. Click to accept the license agreement. 5. Click Install.

    Important

    If a dialog box appears with the following message: Warning: You have chosen to overwrite our existing uninstall of Service Pack 1. Are you sure you want to Continue?, click Yes.

    6. Click Restart on the Windows 2000 Service Pack Setup dialog box when prompted.

    7. Log on to Microsoft Windows 2000. 8. Click Start > Run. 9. Type winver in the Open text box. 10. Verify that Windows 2000 SP2 is installed. 11. Click OK to close the About Windows dialog box.

  • Installing SmartPlant 3D Administrator

    SmartPlant 3D Installation Guide 41

    Related Topics Installing SmartPlant 3D Administrator, page 36 Installing SmartPlant 3D Workstation, page 17

    Install and Verify Microsoft Internet Explorer 6.0 After verifying that the appropriate operating system and service pack software are installed on the administrator system, install Microsoft Internet Explorer 6.0 on to the Microsoft Windows 2000 Professional administrator system.

    Tip

    If the operating system does not have existing Internet connection method, the Internet Connection Wizard appears. Consult your system administrator to establish a connection.

    Verify Microsoft Internet Explorer 6.0 If you have Internet Explorer already installed, verify the version installed by following these steps.

    1. Verify the version of Internet Explorer installed on the administrator system by launching Internet Explorer.

    2. Click Help > About Internet Explorer.

    Note

    If Internet Explorer 6.0 is already installed, the version number displays in the About Internet Explorer dialog box as Version 6.0.2600.0000.

  • Installing SmartPlant 3D Administrator

    42 SmartPlant 3D Installation Guide

    3. If the version is not correct, follow the steps in the next section to install Internet

    Explorer 6.0.

    Install Microsoft Internet Explorer 6.0 1. On the SmartPlant 3D Prerequisite Software Installation window, click

    Administrator Prerequisites. 2. Select Microsoft Internet Explorer 6.0. 3. Click I accept the agreement. 4. Click Next. 5. Click Next. 6. Click Finish to exit Internet Explorer setup and to restart your computer. 7. Log on to Microsoft Windows 2000 Professional. 8. Wait as the different services are configured on the administrator system. 9. Launch Internet Explorer. 10. Click Help > About Internet Explorer.

  • Installing SmartPlant 3D Administrator

    SmartPlant 3D Installation Guide 43

    Tip

    The About Internet Explorer dialog box should display Version 6.0.2600.0000.

    11. Click OK to close the About Internet Explorer dialog box.

    Related Topics Installing SmartPlant 3D Administrator, page 36

    Install Microsoft Office 2000 Several of the SmartPlant 3D tasks require Microsoft Office 2000. SmartPlant 3D designers need Excel to create reports and system administrators rely on Excel to make changes to the reference data spreadsheets and bulk load them into the Catalog database. For more information, see the SmartPlant 3D Reference Data User's Guide, available from the Help>Printable Guides command in the software.

    Important

    Approximately 310 MB of hard disk space is required to load Office 2000 Standard Edition.

    1. Insert the Microsoft Office 2000 CD. 2. Double-click Setup.exe. 3. Enter the appropriate User name, Initials, and Organization information. 4. Click Next on the Welcome to Microsoft Office 2000 page. 5. Click I accept the terms in the License Agreement to accept the License

    Agreement. 6. Click Next. 7. Click Customize. 8. Select the installation location. 9. Click Next. 10. Expand the hierarchy for Microsoft Office.

  • Installing SmartPlant 3D Administrator

    44 SmartPlant 3D Installation Guide

    11. Select Run all from My Computer. 12. Click Install Now.

    Related Topics Installing SmartPlant 3D Administrator, page 36 Installing SmartPlant 3D Workstation, page 17

    Install Microsoft SQL Server 2000 Client Tools After installing Microsoft Windows 2000 Professional, Microsoft Windows 2000 SP2, and Microsoft Internet Explorer 6.0 on the administrator system, you can now install Microsoft SQL Server 2000 Client Tools.

    Warning

    SQL Server 2000 is a separately licensed Microsoft product. Make sure you have a valid license for Microsoft SQL Server 2000 Client Tools software.

    Install Microsoft SQL Server 2000 Client Tools 1. Insert the Microsoft SQL Server 2000 CD.

  • Installing SmartPlant 3D Administrator

    SmartPlant 3D Installation Guide 45

    Tip

    If the compact disc does not autorun, double-click Autorun.exe in the root directory of the compact disc.

    2. On the Microsoft SQL Server Installation page, click SQL Server 2000 Components.

    3. Click Install Database Server. 4. On the Welcome page, click Next. 5. On the Computer Name page, select the Local Computer option, and then click

    Next. 6. On the Installation Selection page, select Create a new instance of SQL

    Server, or install Client Tools, and then click Next. 7. Follow the directions on the User Information, Software License Agreement,

    and related pages. 8. On the Installation Definition pages, select Client tools only, and then click

    Next. 9. On the Select Components pages, accept the defaults, and then click Next. 10. On the Start Copying Files pages, click Next.

    Note

    The status bar displays the progress as the SQL Server 2000 files are copied to the administrator machine. Once the files are installed, the installation script will take a few minutes to start or stop some services, register components, and perform other configuration tasks.

    11. Click Finish on the Setup Complete page. The SQL Server 2000 installation is complete.

    Related Topics Installing SmartPlant 3D Administrator, page 36

    Install SQL Server 2000 Service Pack 2: Database Components

    After installing Microsoft SQL Server 2000 Client Tools on the administrator machine, you can now install SQL Server 2000 SP2: Database Components.

    Warning

    Microsoft SQL Server 2000 Client Tools must be installed on the administrator machine prior to installing SQL Server 2000 SP2. If you have not installed Microsoft SQL Server 2000 Client tools, refer to Install Microsoft SQL Server 2000 Client Tools, page 26 before proceeding.

  • Installing SmartPlant 3D Administrator

    46 SmartPlant 3D Installation Guide

    Install SQL Server 2000 SP2 1. Insert the SmartPlant 3D Prerequisite CD.

    Tip

    If the CD does not start automatically, double-click Setup.exe in the root directory of the CD.

    2. On the SmartPlant 3D Prerequisite Software Installation window, click Administrator Prerequisites.

    3. Select Microsoft SQL Server 2000 Service Pack 2. 4. On the Welcome page, click Next. 5. On the Software License Agreement page, click Yes. 6. On the Start Copying Files page, click Next.

    Tip

    The status bar displays the progress as the component files are copied to the workstation. Once the files are installed, the installation script will take a few minutes to start or stop some services, register components, and perform other configuration tasks.

    7. Click Finish on the Setup Complete page. The SQL Server 2000 SP2 installation is complete.

    Related Topics Installing SmartPlant 3D Workstation, page 17

    Verify Startup of Microsoft Distributed Transaction Coordinator (MSDTC)

    Verify MSDTC is Started 1. Click Start > Settings > Control Panel > Administrative Tools, and double-

    click Services.

    Tip

    You can also right-click My Computer and select Manage. In the Computer Management window, expand the Services and Applications node and click Services.

    2. Locate Distributed Transaction Coordinator in the list of services, and verify that the Status is set to Started and Startup Type is set to Automatic.

    3. If the Distributed Transaction Coordinator service is not started, follow the steps in the next section to start the service; otherwise, proceed to Install the Three-Button Mouse Driver, page 30.

  • Installing SmartPlant 3D Administrator

    SmartPlant 3D Installation Guide 47

    Start MSDTC 1. If the Services window is not open, click Start > Settings > Control Panel >

    Administrative Tools, and double-click Services. 2. To change the Status or Startup Type, right-click on the Distributed

    Transaction Coordinator service, and select Properties from the shortcut menu. 3. On the General tab, select Automatic from the Startup type list. 4. In the Service status section, click Start. 5. Click OK.

    Related Topics Installing SmartPlant 3D Administrator, page 36

    Install the Three-Button Mouse Driver The following steps to install the three-button mouse driver should be performed to ensure correct SmartPlant 3D middle-mouse button functions.

    1. From the root directory of the Intergraph SmartPlant 3D Prerequisite CD, navigate to 3_Button_Mouse_Driver\lmouse_Driver.

    2. Double-click Setup.exe. 3. Select English from the list on the Choose Setup Language dialog box, and then

    click OK. 4. On the Choose Destination Location page, click Next to accept the default

    location.

    Tip

    To select an alternative destination location, click Browse and navigate to the desired location.

    5. On the Select Program Folder page, click Next to accept the default. The required files are installed on the machine.

    6. Click Finish. The system will automatically restart to configure the new files. 7. Log back onto the machine. 8. Click Yes on the New Device message box. The Device Setup Wizard starts. 9. Click Next. 10. Select the side on which the mouse will be positioned, and click Next. 11. In the Other: list, select Middle Button, and then click Next. 12. Check the Make Double-Clicking Easier option, if desired, and then click Next. 13. Click Finish. 14. Click OK on the Mouse Properties dialog box.

  • Installing SmartPlant 3D Administrator

    48 SmartPlant 3D Installation Guide

    Related Topics Installing SmartPlant 3D Workstation, page 17

    Verify an Administrator System for SmartPlant 3D Installation

    Disk Partitioning Important

    Approximately 447 MB of hard disk space is required to load SmartPlant 3D Administrator. Prior to installing SmartPlant 3D Administrator, select and size the workstation's hard disk partitions accordingly. Refer to Disk Partitioning Guidelines, page 10 for additional information.

    SmartPlant 3D version 3.0 has not been certified with other Intergraph PPO software installed on the same system. It is not recommended to install other Intergraph PPO software with the SmartPlant 3D application.

    If it is necessary to install both SmartSketch and SmartPlant 3D version 3.0 on the same system, it is recommended to install SmartSketch before installing the SmartPlant 3D application.

    If you intend to use Unigraphics Solid Edge Version 10 on an administrator system, you must install it prior to running the SmartPlant 3D Administrator setup.

    Caution

    The selected disk partition must be formatted using an NTFS (not FAT 16/32) file system. Verify the file system for the desired partition using Disk Management under Microsoft Windows 2000 Administrative Tools. If the partition is formatted with a FAT 16/32 file system, contact your system administrator to convert it to NTFS before commencing the SmartPlant 3D installation.

    1. Click Start > Settings > Control Panel. 2. Double-click Administrative Tools, and then double-click Computer

    Management. 3. In the console tree under Storage, click Disk Management. 4. Select the disk partition on which you want to install SmartPlant 3D. 5. Right-click the disk partition and select Properties from the shortcut menu. 6. Verify that 447 MB or greater free hard drive space is available on the partition in

    which you plan to install SmartPlant 3D Administrator.

  • Installing SmartPlant 3D Administrator

    SmartPlant 3D Installation Guide 49

    Prerequisite Software Ensure the proper SmartPlant 3D prerequisite software has been installed on the workstation machine according to the instructions outlined in Software Requirements and Loading Order, page 13.

    Related Topics Installing SmartPlant 3D Administrator, page 36

    Install SmartPlant 3D Administrator Important

    Prior to installing SmartPlant 3D on an administrator system, verify that all prerequisite software has been installed. For more information, see Prerequisite Software for SmartPlant 3D Administrator, page 37.

    If you have an older version of SmartPlant 3D Administrator on your machine, uninstall that version before loading the new software. For more information on installing SmartPlant 3D product software, see Remove SmartPlant 3D Software, page 107.

    You need administrator privileges on the system to install the application. 1. Insert the Intergraph SmartPlant 3D Product CD. The following window

    appears:

  • Installing SmartPlant 3D Administrator

    50 SmartPlant 3D Installation Guide

    Tip

    If the CD does not start automatically, double-click Setup.exe in the root directory of the CD.

    2. Select SmartPlant 3D Administrator Installation. 3. Click Next on the SmartPlant 3D Administrator Setup page. 4. On the License Agreement page, select I accept the license agreement, and then

    click Next. 5. Click Next on the Readme Information page. 6. In the Full Name and Organization boxes enter text on the User Information

    page, and then click Next. 7. On the Select Features page, select the product features and the location where

    you want SmartPlant 3D installed:

    Click Browse. Select the directory location for SmartPlant 3D.

    Click OK.

  • Installing SmartPlant 3D Administrator

    SmartPlant 3D Installation Guide 51

    8. Click Next. 9. Click Next on the Ready to Install the Application page to begin installing

    SmartPlant 3D Administrator.

  • Installing SmartPlant 3D Administrator

    52 SmartPlant 3D Installation Guide

    10. On the SmartPlant 3D Administrator Setup page, click Finish to exit the SmartPlant 3D Administrator installation sequence.

    Important

    Restart the computer to complete the installation.

    Related Topics Installing SmartPlant 3D Administrator, page 36

  • Installing SmartPlant 3D SQL Server Data

    SmartPlant 3D Installation Guide 53

    Installing SmartPlant 3D SQL Server Data

    This section describes how to install Intergraph SmartPlant 3D and its recommended prerequisite software on a server machine running Windows 2000 Server or Advanced Server.

    During the SmartPlant 3D SQL Server Data installation process a share is created in [ProductDirectory]\CatalogData\Symbols with the permission set to Everyone as Full Control. Additionally, the template files for the SmartPlant 3D databases are installed, and the Name Generation Service is also configured.

    Important

    Before beginning the installation process, verify that the server meets the specifications described in Hardware Requirements, page 11.

    For optimum performance, we recommend you have all SmartPlant 3D prerequisites installed in order to run the SmartPlant 3D SQL Server Data setup. For more information regarding software specifications, see Software Requirements and Loading Order, page 13.

    You must have administrative privileges on the server to start the installation. See the online Help for Microsoft Windows 2000 for instructions on how to establish administrative privileges.

    Related Topics Install SmartPlant 3D SQL Server Data, page 62

    Prerequisite Software for SmartPlant 3D SQL Server Data

    Prior to loading SmartPlant 3D on a server machine running on a Windows 2000 platform, you must verify that the following prerequisite software is installed:

    Microsoft Windows 2000 SP2

    Microsoft Internet Explorer 6.0

    Microsoft SQL Server 2000

    Microsoft SQL Server 2000 SP2: Database Components

    The following sections provide step-by-step guidelines for verifying and/or installing prerequisite software.

  • Installing SmartPlant 3D SQL Server Data

    54 SmartPlant 3D Installation Guide

    Important

    Before beginning the installation process, verify that the server machine meets the specifications described in Hardware Requirements, page 11.

    For optimal performance, Intergraph PPO recommends installing SmartPlant 3D on systems running on a Windows 2000 platform. For more information regarding software specifications, see Software Requirements and Loading Order, page 13.

    Related Topics Installing SmartPlant 3D SQL Server Data, page 53

    Install and Verify Microsoft Windows 2000 Service Pack 2

    Make sure that Microsoft Windows 2000 Server and Microsoft Windows 2000 SP2 are installed.

    Verify Microsoft Windows 2000 Service Pack 2 1. Click Start > Run. 2. Type winver in the Open text box. 3. Click OK. 4. The About Windows dialog box appears, as shown in the following picture.

    Verify that Microsoft Windows 2000 and Microsoft Windows 2000 SP2 are installed. If the information matches the graphic, proceed to Install and Verify Microsoft Internet Explorer 6.0, page 22. If the information does not match the picture, perform the steps in the next section to install SP2.

  • Installing SmartPlant 3D SQL Server Data

    SmartPlant 3D Installation Guide 55

    5. Click OK to close the About Windows dialog box.

    Install Microsoft Windows 2000 Service Pack 2 1. Insert the Intergraph SmartPlant 3D Prerequisite CD.

    Tip

    If the CD does not autorun, double-click Setup.exe in the root directory of the CD.

    2. On the SmartPlant 3D Prerequisite Software Installation window, click Administrator Prerequisites.

    3. Select Microsoft Windows 2000 Service Pack 2. 4. Click to accept the license agreement. 5. Click Install.

    Important

    If a dialog box appears with the following message: Warning: You have chosen to overwrite our existing uninstall of Service Pack 1. Are you sure you want to Continue?, click Yes.

    6. Click Restart on the page when prompted. 7. Log on to Microsoft Windows 2000.

  • Installing SmartPlant 3D SQL Server Data

    56 SmartPlant 3D Installation Guide

    8. If the Windows 2000 Configure Your Server dialog box appears, close it. 9. Click Start > Run. 10. Type winver in the Open text box. 11. In the About Windows dialog box, verify that Microsoft Windows 2000 SP2 is

    installed. 12. Click OK to close the About Windows dialog box.

    Related Topics Installing SmartPlant 3D Administrator, page 36 Installing SmartPlant 3D SQL Server Data, page 53

    Install and Verify Microsoft Internet Explorer 6.0 After verifying that the appropriate operating system and service pack software exists on the server, install Microsoft Internet Explorer 6.0 on the Microsoft Windows 2000 server machine.

    Tip

    If the operating system does not have predefined Internet connection method, the Internet Connection Wizard appears. Consult your system administrator to establish a connection.

    Verify Microsoft Internet Explorer 6.0 If you have Internet Explorer already installed, verify the version installed by following these steps.

    1. Verify the version of Internet Explorer installed on the server by launching Internet Explorer.

    2. Click Help > About Internet Explorer.

    Note

    If Internet Explorer 6.0 is installed, then the version number appears in the About Internet Explorer dialog box as Version 6.0.2600.0000.

  • Installing SmartPlant 3D SQL Server Data

    SmartPlant 3D Installation Guide 57

    3. If the version is not correct, follow the steps in the next section to install Internet

    Explorer 6.0.

    Install Microsoft Internet Explorer 6.0 1. On the SmartPlant 3D Prerequisite Software Installation dialog box, click

    Administrator Prerequisites. 2. Select Microsoft Internet Explorer 6.0. 3. Click I accept the agreement. 4. Click Next. 5. Click Next. 6. Click Finish to exit Internet Explorer setup and to restart your computer. 7. Log on to Microsoft Windows 2000. 8. Wait as the different services are configured on the server. 9. Launch Internet Explorer. 10. Click Help > About Internet Explorer.

  • Installing SmartPlant 3D SQL Server Data

    58 SmartPlant 3D Installation Guide

    Tip

    The About Internet Explorer dialog box should display Version 6.0.2600.0000.

    11. Click OK to close the About Internet Explorer dialog box.

    Related Topics Installing SmartPlant 3D SQL Server Data, page 53

    Install Microsoft SQL Server 2000 After installing the Microsoft Windows 2000 Server and Microsoft Windows 2000 SP2 on the server, you can install Microsoft SQL Server 2000.

    Warning

    SQL Server 2000 is a separately licensed Microsoft product. Make sure you have a valid license for Microsoft SQL Server 2000 software.

    1. Insert the Microsoft SQL Server 2000 CD.

    Tip

    If the compact disc does not launch automatically, double-click Autorun.exe in the root directory of the compact disc.

    2. On the Microsoft SQL Server 2000 Installation window, click SQL Server 2000 Components.

    3. Click Install Database Server. 4. On the Welcome page, click Next. 5. On the Computer Name page, select Local Computer. 6. Click Next. 7. On the Installation Selection page, select Create a new instance of SQL Server

    or install Client Tools, and then click Next. 8. Follow the instructions on the User Information and Software License

    Agreement pages. 9. On the Installation Definition page, select Server and Client Tools, and then

    click Next.

    Tip

    Approximately 208KB of free space is initially required; however, a typcial installation requires approximately 151MB of space on the system page, regardless of the location of the program or data files.

    10. On the Instance Name page, select Default and click Next. 11. Make the following selections on the Setup Type page:

  • Installing SmartPlant 3D SQL Server Data

    SmartPlant 3D Installation Guide 59

    Select the Typical installation. Click Browse to specify the drive location for the program files

    (typically the C:\Program Files\Microsoft SQL Server\ drive). Approximately 38MB of free space is required.

    Click Browse to specify the Data Files drive location.

    Note

    This location can be different from where the actual Microsoft SQL Server program files were installed. Approximately 35MB of free space is initially required, but the space used by the data files will grow as you create SmartPlant 3D data. In addition, a typical installation requires approximately 183MB of space on the system drive, regardless of the location of the program or data files.

    12. Click Next on the Setup Type page. 13. Make the following selections on the Services Accounts page:

    Select Use the same account for each service. Auto start SQL Server Service button.

    In the Service Settings area, select the Use the Local System Account button.

    14. Click Next on the Services Accounts page. 15. In the Authentication Mode page, select Windows Authentication Mode, and

    then click Next. 16. On the Start Copying Files page, click Next. 17. On the Choose Licensing Mode page, make selections according to your license

    agreement, and click Continue to begin the installation.

  • Installing SmartPlant 3D SQL Server Data

    60 SmartPlant 3D Installation Guide

    18. Click Finish on the Setup Complete page. The SQL Server 2000 installation is

    complete.

    Related Topics Installing SmartPlant 3D SQL Server Data, page 53

    Install SQL Server 2000 Service Pack 2: Database Components

    After installing Microsoft SQL Server 2000 on the server machine, you can now install SQL Server 2000 SP2: Database Components.

    Warning

    Microsoft SQL Server 2000 must be installed on the server machine prior to installing SQL Server 2000 SP2. If you have not installed Microsoft SQL Server 2000, refer to Install Microsoft SQL Server 2000, page 58 before proceeding.

    Install SQL Server 2000 SP2: Database Components 1. Insert the SmartPlant 3D Prerequisite CD.

  • Installing SmartPlant 3D SQL Server Data

    SmartPlant 3D Installation Guide 61

    Tip

    If the CD does not start automatically, double-click Setup.exe in the root directory of the CD.

    2. On the SmartPlant 3D Prerequisite Software Installation window, click Server Prerequisites.

    3. Select Microsoft SQL Server 2000 Service Pack 2. 4. On the Welcome page, click Next. 5. On the Software License Agreement page, click Yes. 6. On the Instance Name page, click Next. 7. On the Start Copying Files page, click Next. 8. On the Connect to Server page, select The Windows information I use to log

    on to my computer with (Windows Authentication) and click Next.

    Tip

    The status bar displays the progress as the component files are copied to the workstation. Once the files are installed, the installation script will take a few minutes to start or stop some services, register components, and perform other configuration tasks.

    9. On the page that says You should now backup your master and msdb databases since this installation has updated their content, click Next.

    10. Click Finish on the Setup Complete page. The SQL Server 2000 SP2 installation is complete.

    Important

    Restart your machine to ensure that all settings take effect.

    Related Topics Installing SmartPlant 3D Workstation, page 17

    Verify Automatic Startup of Microsoft SQL Server 2000 Services

    1. Click Start > Settings > Control Panel > Administrative Tools, and double-click Services.

    Tip

    You also can right-click My Computer and select Manage. In the Computer Management window, expand the Services and Applications node and click Services.

    2. Verify that the Status field is set to Started and the Startup Type field is set to Automatic, for each of the following services:

  • Installing SmartPlant 3D SQL Server Data

    62 SmartPlant 3D Installation Guide

    Distributed Transaction Coordinator

    Microsoft Search

    MSSQLServer 3. To change the Status or Startup Type fields, right-click the service name, and

    select Properties from the shortcut menu. 4. On the General tab, select Automatic from the Startup type list. 5. In the Service status section, click Start. 6. Click OK.

    Related Topics Installing SmartPlant 3D SQL Server Data, page 53

    Install SmartPlant 3D SQL Server Data Important

    Prior to installing SmartPlant 3D on the server, verify that all prerequisite software has been installed. For more information, see Prerequisite Software for SmartPlant 3D Server, page 53.

    1. Insert the Intergraph SmartPlant 3D Product CD. The following screen appears:

  • Installing SmartPlant 3D SQL Server Data

    SmartPlant 3D Installation Guide 63

    2. Select SmartPlant 3D SQL Server Data Installation. 3. Click Next on the SmartPlant 3D SQL Server Data Setup page. 4. On the License Agreement page, select I accept the license agreement, and then

    click Next. 5. Click Next on the Readme Information page. 6. In the Full Name and Organization pages, enter text on the User Information

    dialog box, and then click Next. 7. On the Select Features page, click Next to accept the default installation

    directory.

    Important

    During its installation, the SQL Server Data software automatically creates a Symbols directory and shares it out on the server machine. All SmartPlant 3D users require both Full Control disk access and Full Control share permissions for the Symbols directory. If you install the SQL Server Data in the default directory (C:\Program Files\SmartPlant\3D\), you must access the Properties page for the

  • Installing SmartPlant 3D SQL Server Data

    64 SmartPlant 3D Installation Guide

    Symbols directory and set the share permissions on the Sharing tab and the disk access permissions on the Security tab to Full Control.

    Tip

    If you wish to select an alternative location, click Browse, navigate to the desired directory location, and then click OK.

    8. On the Server Access page, enter a username with the administrative privileges to

    the server machine. 9. In the Password and Confirm Password fields, enter the user's correct password,

    and then click Next. 10. Click Next on the Ready to Install the Application page to begin installing

    SmartPlant 3D. 11. On the SmartPlant 3D SQL Server Data Setup page, click Finish to exit the

    SmartPlant 3D SQL Server Data installation sequence.

  • Installing SmartPlant 3D SQL Server Data

    SmartPlant 3D Installation Guide 65

    Warning

    If a "Name Generation service configuration failed." error message displays, you must configure the name generation service manually. Refer to the section entitled Install and Configure the COM+ Application on a Windows 2000 Server, page 65 for more information.

    Important

    Restart the computer to complete the installation.

    Related Topics Installing SmartPlant 3D SQL Server Data, page 53

    Install and Configure the COM+ Application on a Windows 2000 Server

    Perform the following steps to manually configure the SP3DNameGenerator application on a server running Windows 2000.

    Important

    This procedure is only necessary if you received the Name Generation service configuration failed. Failed to update password in the SP3DNameGenerator error message during the SmartPlant 3D SQL Server Data installation process.

  • Installing SmartPlant 3D SQL Server Data

    66 SmartPlant 3D Installation Guide

    You must have administrator privileges on the server in order to perform this installation procedure.

    1. Click Start > Settings > Control Panel, and then double-click Administrative Tools.

    2. In the Administrative Tools window, double-click Component Services to start the component services MMC snap-in. The Component Services window displays.

    3. Expand the Component Services node under the Console Root, and then expand

    the Computers and My Computer nodes.

  • Installing SmartPlant 3D SQL Server Data

    SmartPlant 3D Installation Guide 67

    4. Expand the COM+ Applications node. 5. Verify the SP3DNameGenerator icon appears under COM+ Applications. If it

    exists, skip to step 13. If it does not exits, perform steps 6-12.

  • Installing SmartPlant 3D SQL Server Data

    68 SmartPlant 3D Installation Guide

    6. Select Com+ Applications under the My Computer node, and then click

    Action>New>Application on the horizontal toolbar. The COM+ Application Install Wizard displays.

  • Installing SmartPlant 3D SQL Server Data

    SmartPlant 3D Installation Guide 69

    7. Click Next on the Welcome to the COM Application Install Wizard page. 8. Select Create an empty application on the Install or Create a New Application

    page. 9. On the Create an Empty Application page, type SP3DNameGenerator in the

    Enter a name for the new application text box. 10. Select Server application as the Activation type, and then click Next. 11. On the Set Application Identity page, enter the user name and password to set

    the proper identity under which the COM+ application will run on the server, and then click Next.

    Note

    This needs to be an account with Windows administrative privileges on the server.

    12. Click Finish to begin the installation.

    Note

    When installation completes, a SP3DNameGenerator node is placed under COM+ Applications.

  • Installing SmartPlant 3D SQL Server Data

    70 SmartPlant 3D Installation Guide

    13. Next, expand the SP3DNameGenerator node to add/verify the existence of the

    NTNameGenerator.UpdateNumber.1 component. 14. Expand the Components node. Verify the

    NTNameGenerator.UpdateNumber.1 component appears. If it exists, skip to step 19. If it does not exist, perform steps 15-18.

    15. On the horizontal toolbar, click Action>New>Component. The COM Component Installation Wizard displays.

    16. Click Next on the Welcome to the COM Component Install Wizard. 17. Select Install new component(s) and browse for NTNameService.dll

    Tip

    The component .dll is located in [Product Directory]:\CommanApp\Server\Bin.

    18. Click Next on the Install new components page, and then click Finish to complete the installation procedure.

    Note

    The Component Services window displays that the NTNameService.UpdateNumber.1 component is installed in the SP3DNameGenerator Application.

  • Installing SmartPlant 3D SQL Server Data

    SmartPlant 3D Installation Guide 71

    19. If you entered the user name and password on the Set Application Identity page

    in step 11, then you are finished with this procedure. If you did not, perform steps 20-24.

    20. Select the SP3DNameGenerator application icon. 21. Click Action>Properties, and then click on the Identify tab. 22. Select the This user: option. 23. Enter the user and password to set the proper identity under which the COM+

    application will run on the server.

    Note

    This needs to be an account with Windows administrative privileges on the server.

    24. Click OK to complete the configuration procedure.

  • Install Optional Software for SmartPlant 3D

    72 SmartPlant 3D Installation Guide

    Install Optional Software for SmartPlant 3D

    Once the Intergraph SmartPlant 3D prerequisite and main application software is installed on the administrator or client workstation, you can now begin installing other programming software. SmartPlant 3D is compatible with Microsoft Visual Basic 6.0 with Visual Studio Service Pack 5 and Unigraphics Solid Edge Version 10. While not a requirement for using SmartPlant 3D, this additional software provides enhanced functionality. For example, to create or edit orthographic drawing view styles in the Drawings and Reports task, you must install Visual Basic on the local machine.

    Warning

    F