small products technical manual
TRANSCRIPT
Small Products Technical Manualfor Powered and Passive Panels
2
Active (Powered) Panels Part # Page4SourceSwitcherPanel SH-4SWSS 25MicPreampPanel SH-MIC 26MicPreampw/PTTPanel SH-MICPTT 27MicPreampw/PTTPanel* SH-MICPTT 28HeadphoneAmplifierPanel SH-HPB 29DualHeadphoneAmp.Panel SH-HPDUAL 30MonitorLevelControlPanel SH-LEVEL 31MonitorAmpPanel SH-AMPw/oSpeaker 32 SH-AMPSPKRw/Speaker 32Ampw/Headphone SH-AMPHPN 33DualVUMeterPanel SH-VUV(Vertical) 34 SH-VUH(Horizontal) 343MixerPanel(Input) SH-MIXER 353MixerPanel(Output) SH-MIXER 36LCDDisplayPanel SH-LCDV(Vertical) 37 SH-LCDH(Horizontal) 37In/OutBalancedMatchJack SH-DUALMATCH 38In/OutBalancedMatchJack SH-MATCHPANEL 39On/Off/CoughPanel SH-ONOFFCOUGH 40
Warranty/RepairPolicy/Returns
Table of Contents
* Obsolete Part
Part # PageStudioHub+ Standard Pinout & Power Consumptions Illustration 3HowtoPowerStudioHub+-viaPS-Cube 4HowtoPowerStudioHub+-viaaHuborWall-Wart 5
Active (Powered) MatchJacksMatchJackPreamp,Input MJ-IN 6MatchJackPreamp,Output MJ-OUT 7AES/EBUtoS/PDIFConverter MJ-SPDIFIN 8S/PDIFtoAES/EBUConverter MJ-SPDIFOUT 9 AnalogtoDigitalConverter MJ-AD 10DigitaltoAnalogConverter MJ-DA 11DigitalDistributionAmplifier MJ-DDA 12
Passive PanelsDualXLRFemaleAdapterMono/Stereo SH-2XLRF 13DualXLRMaleAdapterMono/Stereo SH-2XLRM 14DualXLRMale-FemalePanel SH-2XLRMF 15SingleXLRFemalePanel SH-1XLRF 16SingleXLRMalePanel SH-1XLRM 17SingleXLR5-PinFemalePanel SH-1XLRF5PIN 181/4”&MiniTRSPanel(Unbalanced) SH-1/4UNBAL 191/4”&MiniTRSPanel(Balanced) SH-1/4BAL 204SourceSwitcherPanel SH-4SW* 21 BreakoutAdapter ADAPT-BO 22BreakoutAdapter ADAPT-GPI 23PS-CUBE“DC-Link”PowerInserter PS-CUBE 24 MicSingleXLRFemalew/PTTPanel SH-MICPTTPAS 27
3(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
StudioHub+Standard Pinout
(T568B Standard)
Current consumption for each StudioHub+ active device. Refer to this list when calculating the total number of devices that can be run together on any individual power supply.
Part # Description Current MJ-OUT Analog MatchJack Out (IHF to Pro) 75ma MJ-IN Analog MatchJack In (Pro to IHF) 35ma MJ-SPDIFOUT SPDIF OUT (S/PDIF and Optical to AES) 100ma MJ-SPDIFIN SPDIF IN (AES to S/PDIF) 0 (passive)MJ-AD Digital MatchJack A to D 150ma MJ-DA Digital MatchJack D to A 150ma MJ-DDA Digital MatchJack Distribution Amplifier 165ma* SH-DUALMATCH Dual Match Panel 100ma SH-HP Headphone Panel 100maSH-MIC Mic Pre-Amp Panel 55maSH-MIXER 3 Input Stereo Mixer with mix-minus 125ma SH-AMPSPKR Monitor Amp Panel (w/ Speaker) 1400maSH-LEVEL Monitor Panel 145maSH-VUV Dual VU Meter Panel 150maSH-LCDV LCD Display Panel 75maDA6-DC DA Hub (Single) 575maSUM4-DC Combiner Hub (Single) 175ma
+ - G - +LEFT RIGHT
Stand-Alone VersionsSome active StudioHub+ products were previously available in “Stand-Alone” versions with barrier strip connectivity for audio I/O. The following illustrates the pinout for this barrier strip.
* Powered via 9v DC (single ended) wall wart or +/-15vDC StudioHub+ power supply
+1 (615) 763-3033 • www.studiohub.com
Revised 4-21-10
4
Powering StudioHub+ Active Devices
Many StudioHub+ devices are active and are powered by +/- 15vDC. Power can be supplied via the StudioHub+ “DC-Link”system that uses CAT-5 pair #4 (White/Brown) for power, or power can be supplied via a separate power supply.See the current consumption chart to determine how many devices can be powered with different systems.
II - Powering Via a Hub (for up to 16 devices)
I - Powering via PS-Cube (for up to 4 devices)
Use any Hub in which the model number ends in “DC”(HUB18-DC or HUB36-DC or HUB8-DC or HUB16-DC
PS-EXTU
Headphone amps linktogether for audio & DC
SH-HP SH-HP
SH-MICMatchJack
D to AConverter
From 4 separateaudio sends or feeds
Headphone amps linktogether for audio & DC
SH-HP
SH-MIC
MatchJack
SH-HP
PS-Cube
Power a PS-CUBE from aRadio Systems Console
Use cable # 16998(6') / 15884(1')(3-pin MTA to 3-pin MTE)
MatchJack
III - Powering via a “Wall Wart” or Desk-Top Power Supply
SH-HPSH-HP
Headphone amps link together for audio & DC.Power up to 4 headphone amps from one PS-WWU
and up to 2 headphone amps from 1 PSWW
D to AConverter
3 amp bi-polar15vDC power supply
Power a PS-CUBE from aRS Console Power Supply
Use cable # 16600(16-pin MR-16 to 5-pin MTA)
Power a PS-CUBE from aPS-EXTU Power Supply(the cable is included)
(4-pin MR-4 to 5-pin MTA)
1 Amp
1 Amp3 Amps 400 ma
Power a PS-CUBE from aPS-WWCUBE Power Supply(the captive cable is included)
(captive to 3-pin MTE)
200 ma
NOTE – All power supplies shown are Universal Voltageswitching supplies and accept from 100 to 240VAC input
power EXCEPT the “non Universal Wall-Wart”PS-WWCUBE and PS-WWSH supplies
which are 110VAC input power only.Power an individual MatchJack or Panel
from a PSWW-SH Power Supply(the captive 3-pin to MTA cable
is included)
Power multiple Panelsfrom a PSWWU-SH Power Supply
(the captive 3-pin to MTA cableis included)
Power a PS-CUBE from aPS-WWUCUBE Power Supply(the captive cable is included)
(captive to 3-pin MTE)
5-pin MTA & 3-pin MTEpower connectors (in parallel)
How to Power StudioHub+ - via PS-Cube
Revised 4-21-10
5
Powering StudioHub+ Active Devices
Many StudioHub+ devices are active and are powered by +/- 15vDC. Power can be supplied via the StudioHub+ “DC-Link”system that uses CAT-5 pair #4 (White/Brown) for power, or power can be supplied via a separate power supply.See the current consumption chart to determine how many devices can be powered with different systems.
II - Powering Via a Hub (for up to 16 devices)
I - Powering via PS-Cube (for up to 4 devices)
Use any Hub in which the model number ends in “DC”(HUB18-DC or HUB36-DC or HUB8-DC or HUB16-DC
PS-EXTU
Headphone amps linktogether for audio & DC
SH-HP SH-HP
SH-MICMatchJack
D to AConverter
From 4 separateaudio sends or feeds
Headphone amps linktogether for audio & DC
SH-HP
SH-MIC
MatchJack
SH-HP
PS-Cube
Power a PS-CUBE from aRadio Systems Console
Use cable # 16998(6') / 15884(1')(3-pin MTA to 3-pin MTE)
MatchJack
III - Powering via a “Wall Wart” or Desk-Top Power Supply
SH-HPSH-HP
Headphone amps link together for audio & DC.Power up to 4 headphone amps from one PS-WWU
and up to 2 headphone amps from 1 PSWW
D to AConverter
3 amp bi-polar15vDC power supply
Power a PS-CUBE from aRS Console Power Supply
Use cable # 16600(16-pin MR-16 to 5-pin MTA)
Power a PS-CUBE from aPS-EXTU Power Supply(the cable is included)
(4-pin MR-4 to 5-pin MTA)
1 Amp
1 Amp3 Amps 400 ma
Power a PS-CUBE from aPS-WWCUBE Power Supply(the captive cable is included)
(captive to 3-pin MTE)
200 ma
NOTE – All power supplies shown are Universal Voltageswitching supplies and accept from 100 to 240VAC input
power EXCEPT the “non Universal Wall-Wart”PS-WWCUBE and PS-WWSH supplies
which are 110VAC input power only.Power an individual MatchJack or Panel
from a PSWW-SH Power Supply(the captive 3-pin to MTA cable
is included)
Power multiple Panelsfrom a PSWWU-SH Power Supply
(the captive 3-pin to MTA cableis included)
Power a PS-CUBE from aPS-WWUCUBE Power Supply(the captive cable is included)
(captive to 3-pin MTE)
5-pin MTA & 3-pin MTEpower connectors (in parallel)
How to Power StudioHub+ - via a Hub or Wall-Wart
6
Revised 4-21-10
Part # MJ-IN StudioHub+ MatchJack Preamp, Input(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
JU1 Install to connect shield ground to power ground
Leftleveladjust
Rightleveladjust
AudioandpowerinputprovidedonRJ-45
Directpowerinput+/-15voltsDC
RightoutputRCAPowerLEDLeftoutputRCA
+1 (615) 763-3033 • www.studiohub.com
7
Revised 4-21-10
Part # MJ-OUT StudioHub+ MatchJack Preamp, Output(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
JU1 Install to connect shield ground to power ground
Leftleveladjust
Rightleveladjust
Directpowerinput+/-15voltsDC
RightinputRCALeftinputRCA
AudioandpowerinputprovidedonRJ-45
PowerLED
+1 (615) 763-3033 • www.studiohub.com
8
Revised 4-21-10
ASM STAND ALONE 12342ASM STUDIOHUB+ 12341
J1
J2
J3
R2
ASM
JU1
R1 R1
T1
Part # MJ-SPDIFIN StudioHub+ S/PDIF to AES/EBU Converter(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
*RCAS/PDIFoutput
StudioHub+AES/EBURJ-45input
JU1
Install to connect shield ground to power ground
+1 (615) 763-3033 • www.studiohub.com
9
Revised 4-21-10
Part # MJ-SPDIFOUT StudioHub+ S/PDIF to AES/EBU Converter(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
Directpowerin+/-15voltsDC
*RCAS/PDIFinput *OpticalInput
StudioHub+AES/EBUoutputandpowerin
JU1
Install to connect shield ground to power ground
*Useonlyone
+1 (615) 763-3033 • www.studiohub.com
10
Revised 10-30-15
Part # MJ-AD StudioHub+ Analog to Digital Converter(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
DCpowerin+/-15voltsDCincluded(RadioSystemsPart#PS-UCUBE)UnitcanalsobepoweredbyStudioHub+“DC-Link”viaRJ-45’s.
JU7, JU8
Install to connect RJ-45 shield to ground to power ground
Unbalanced InputsBalanced
InputAES/EBUOutput
Left Right
JU3 JU4 JU5 JU6
Set Input Level
Pro Level Input
IHF
CD
CD
CD
PRO
Set Nominal Input Sensitivity*
Shortalllowerpins
0dBuShortUpperPins ShortLowerPins ShortNoPins
+4dBu +8dBu
JU1 JU2 JU1 JU2 JU1 JU2
JU3 JU4 JU5 JU6
Set Input Level
Consumer Level Input
IHF
CD
CD
CD
PRO
Set Nominal Input Sensitivity*
Shortallupperpins
-15dBvShortUpperPins ShortLowerPins
*Setforstationstandardreferenceleveltoprovideunitoutputheadroomof20dB.
ShortNoPins-10dBv -6dBv
JU1 JU2 JU1 JU2 JU1 JU2
+15vG-15v
REDBLUWHT
PowerSupplyConnector
+1 (615) 763-3033 • www.studiohub.com
11
Revised 10-30-15
Part # MJ-DA StudioHub+ Digital to Analog Converter(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
AES/EBU InputTOSlink InputCoaxial InputAnalog Output
+15vG-15v
REDBLUWHT
PowerSupplyConnector
JU1 and Ju2
Install to connect RJ-45 shield to ground
DCpowerin+/-15voltsDCincluded(RadioSystemsPart#PS-UCUBE)UnitcanalsobepoweredbyStudioHub+“DC-Link”viaRJ-45’s.
+1 (615) 763-3033 • www.studiohub.com
12
Revised 10-30-15
(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
AESOutput#1 AESOutput#2 AESOutput#3
AESInput
AESOutput#4
JU1 - Ju5
Install to connect RJ-45 shield to ground
DCpowerin+9voltsDCincluded.(RadioSystemsPart#16213).UnitcanalsobepoweredbyStudioHub+“DC-Link”viaRJ-45’s
Part # MJ-DDA StudioHub+ Digital Distribution Amplifier+1 (615) 763-3033 • www.studiohub.com
13
Revised 4-21-10
Part # SH-2XLRF StudioHub+ Dual XLR Female Adapter Mono/Stereo(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
Install JU3 to connect Left XLR pin 1 to chassis ground
Install JU4 to connect Right XLR pin 1 to chassis ground
JU1 JU2
Left RightInstall to connect XLR Pin 1 to RJ-45 shield
StudioHub+RJ45“A”formonoonlyorstereooperation
When programmed for stereo operation:L&RXLRfeedbothRJ45’sinstereo.
When programmed for Mono Operation: LeftXLRfeedsRJ45-1,pins1&2only.RightXLRfeedsRJ45-2,pins1&2only.
StudioHub+RJ45“B”forstereooperation
To configure for stereo operation
JU5
JU6
JU7, JU8, JU9, JU10
To configure for mono operation
JU5
JU6
JU7, JU8, JU9, JU10
JU1 JU2 Install to connect XLR Pin 1 to RJ-45 power ground (RJ-45 pin 4)
RJ45 shield and ground select jumpersXLR PIN1 select jumper
87654321
2 1
3
2 1
3
87654321
2 1
3
87654321
LeftXLR
RightXLR
LeftXLR
RJ-45 #1
CHASSISGROUND
RJ-45 #2JU1
JU2
RJ-45 #1
87654321
2 1
3
RightXLR
RJ-45 #2
87654321
2 1
3
2 1
3
87654321
LeftXLR
RightXLR
CHASSISGROUND
RJ-45 #2
JU3
JU1
RJ-45 #1
JU2
JU4
CHASSISGROUND
CHASSISGROUND
JU3
JU1
JU4
JU2
CHASSISGROUND
CHASSISGROUND
CHASSISGROUND
CHASSISGROUND
CHASSISGROUND
87654321
2 1
3
2 1
3
87654321
2 1
3
87654321
LeftXLR
RightXLR
LeftXLR
RJ-45 #1
CHASSISGROUND
RJ-45 #2JU1
JU2
RJ-45 #1
87654321
2 1
3
RightXLR
RJ-45 #2
87654321
2 1
3
2 1
3
87654321
LeftXLR
RightXLR
CHASSISGROUND
RJ-45 #2
JU3
JU1
RJ-45 #1
JU2
JU4
CHASSISGROUND
CHASSISGROUND
JU3
JU1
JU4
JU2
CHASSISGROUND
CHASSISGROUND
CHASSISGROUND
CHASSISGROUND
CHASSISGROUND
+1 (615) 763-3033 • www.studiohub.com
14
Revised 4-21-10
Part # SH-2XLRM StudioHub+ Dual XLR Male Adapter Mono/Stereo(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
StudioHub+RJ45“A”formonoonlyorstereooperation
When programmed for stereo operation:L&RXLRfeedbothRJ45’sinstereo.
When programmed for mono operation: LeftXLRfeedsRJ45-1,pins1&2only.RightXLRfeedsRJ45-2,pins1&2only.
StudioHub+RJ45“B”forstereooperation
To configure for stereo operation
JU5
JU6
JU7, JU8, JU9, JU10
To configure for mono operation
JU5
JU6
JU7, JU8, JU9, JU10
87654321
2 1
3
2 1
3
87654321
2 1
3
87654321
LeftXLR
RightXLR
LeftXLR
RJ-45 #1
CHASSISGROUND
RJ-45 #2JU1
JU2
RJ-45 #1
87654321
2 1
3
RightXLR
RJ-45 #2
87654321
2 1
3
2 1
3
87654321
LeftXLR
RightXLR
CHASSISGROUND
RJ-45 #2
JU3
JU1
RJ-45 #1
JU2
JU4
CHASSISGROUND
CHASSISGROUND
JU3
JU1
JU4
JU2
CHASSISGROUND
CHASSISGROUND
CHASSISGROUND
CHASSISGROUND
CHASSISGROUND
87654321
2 1
3
2 1
3
87654321
2 1
3
87654321
LeftXLR
RightXLR
LeftXLR
RJ-45 #1
CHASSISGROUND
RJ-45 #2JU1
JU2
RJ-45 #1
87654321
2 1
3
RightXLR
RJ-45 #2
87654321
2 1
3
2 1
3
87654321
LeftXLR
RightXLR
CHASSISGROUND
RJ-45 #2
JU3
JU1
RJ-45 #1
JU2
JU4
CHASSISGROUND
CHASSISGROUND
JU3
JU1
JU4
JU2
CHASSISGROUND
CHASSISGROUND
CHASSISGROUND
CHASSISGROUND
CHASSISGROUND
JU1 JU2
JU1 JU2
Left Right
JU1 JU2
Install to connect XLR Pin 1 to RJ-45 shield
Install to connect XLR Pin 1 to RJ-45 power ground (RJ-45 pin 4)
RJ45 shield and ground select jumpers
Install JU3 to connect Left XLR pin 1 to chassis ground
Install JU4 to connect Right XLR pin 1 to chassis ground
XLR PIN1 select jumper
+1 (615) 763-3033 • www.studiohub.com
15
Revised 4-21-10
Part# SH-2XLRMF StudioHub+ Dual XLR Male/Female Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
RJ45-1 RJ45-2
FemaleXLR MaleXLR
Install JU1 to connect XLR(s) pin 1 to chassis ground
JU2
Install to connect XLR(s) pin 1 to StudioHub+ RJ45 shield
JU2
Install to connect XLR(s) pin 1 to StudioHub+ RJ45 power ground (RJ-45 pin 4)
2 1
3
87654321
FemaleXLR
RJ-45 #1
87654321
2 1
3
MaleXLR
RJ-45 #2
CHASSISGROUND
JU1
JU2
JU1
JU2
CHASSISGROUND
CHASSISGROUND
CHASSISGROUND
+1 (615) 763-3033 • www.studiohub.com
16
Revised 4-21-10 (Note-Thereisastereoonlyversionofthisproduct.
Seewww.studiohub.com/legacy.php)
ASSEMBLY 12044B
STUD
IOHU
B+
F XL
R TO
RJ4
5
JU4JU3
JU1
JU2
J1
J2
Part # SH-1XLRF StudioHub+ Single XLR Female Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
JU1
Install to connect XLR pins to chassis ground
JU2
Install to connect XLR pins to power ground
Install to connect XLR pin 1 to shield ground
JU3, JU4
Install for left and right in parallel Remove for left only
XLR
+1 (615) 763-3033 • www.studiohub.com
17
Revised 4-21-10(Note-Thereisastereoonlyversionofthisproduct.
Seewww.studiohub.com/legacy.php)
ASSEMBLY 12044B
STUD
IOHU
B+
M X
LR TO
RJ4
5
JU4JU3
JU1
JU2
J1
J2
Part # SH-1XLRM StudioHub+ Single XLR Male Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
JU1
Install to connect XLR pins to chassis ground
JU2
Install to connect XLR pins to power ground
Install to connect XLR pin 1 to shield ground
JU3, JU4
Install for left and right in parallel Remove for left only
XLR
+1 (615) 763-3033 • www.studiohub.com
Modified 6-18-14
18Part # SH-1XLRF5Pin StudioHub+ Single XLR 5Pin Female Panel
(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
JU4
Install to connect XLR pins to XLR chassis ground
Install to connect external power to light mic boom LED (5-15VDC) via pins 3 & 4 on barrier strip connector
Install to connect external power to light mic boom LED (15VDC) via pin 8 of RJ-45 when connected to a standard StudioHub+ powered Cube or Hub.
JU1, JU2
Install both jumpers to apply left and right mic audio in parallel on RJ-45 connector (StudioHub+ standard pins 1 & 2 for left, and pins 3 & 6 for right). Remove both jumpers to apply mic audio to left channel only.
5-PinXLR(Mating5-pinmalein-linemale
XLRconnectorincluded)
5-Pin XLR Pin Out
1 - Ground2 - Audio+3 - Audio–4 - LED–5 - +DCV
NOTE:UnusedStudioHub+RJ-45pin5(CAT-5wht/bluwire)isconnectedtolightmicboomLEDwhenconnectedtoground(DCvoltagemustbeprovidedeitherviabarrierstrippin4orStudioHub+pin8.ProgramJU3accordingly).
JU3
+5-1
5VDC
Gnd
Pull-
to-G
nd t
olig
ht L
EDGnd
Made for Yellowtec Mic Arms
+1 (615) 763-3033 • www.studiohub.com
19
Revised 4-21-10
ASSEMBLY 12362
UNBAL WORLD
GND
SHLD
SHLD
GND
SLV
L-
R-
STUDIOHUB+
JU6
JU4
JU5
JU3
JU1 JU2
J4J3
J6J5
J2J1
Part # SH-1/4UNBAL StudioHub+ 1/4” & Mini TRS Panel (Unbalanced)(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
JU1 and JU2* Install to tie StudioHub+ RJ45 right - connection to StudioHub+ shield.
Install to tie StudioHub+ RJ45 right - connection to StudioHub+ power ground.
JU3 and JU4* Install to tie StudioHub+ RJ45 left - connection to StudioHub+ shield.
Install to tie StudioHub+ RJ45 left - connection to StudioHub+ power ground.
JU5 and JU6* Install to tie 1/4” and mini TRS sleeve to StudioHub+ RJ45 shield.
Install to tie 1/4” and mini TRS sleeve to StudioHub+ RJ45 power ground.
*Improper use of JU1, JU2, JU3, JU4 may result in no output, excessive noise, crosstalk, oscillation, or circuit failure.
StereounbalancedStudioHub+RJ45.Signalto/fromJ4andJ6
StereounbalancedStudioHub+RJ45.Signalto/fromJ3andJ5
1/4”andminiTRSJ3andJ5areinparallel.Useonlyoneatatime.
Stereounbalanced1/4”
StereounbalancedminiTRS
Stereounbalanced1/4”
StereounbalancedminiTRS1/4”andminiTRSwiring
Tip=Left+StudioHub+RJ45connection
Ring=RightStudioHub+RJ45connection
Sleeve=SeeJU5andJU6
1/4”andminiTRSJ4andJ6areinparallel.Useonlyoneatatime.
+1 (615) 763-3033 • www.studiohub.com
20
Revised 4-21-10
ASSEMBLY 12007
STUDIOHUB+
1/4" AND MINI TRS
JU1
J4J3
J6J5
J2J1
Part # SH-1/4BAL StudioHub+ 1/4” & Mini TRS Panel (Balanced)(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
1/4”TRS&miniTRS,(J3/J4andJ5/J6)areinparallel.Useonlyoneatatime.
Leftbalanced1/4”TRS
LeftbalancedminiTRS
RightbalancedminiTRS
Rightbalanced1/4”TRS
1/4”miniTRS(J3,J4,J5,J6)wiringTip=+Ring=—Sleeve=SeeJU1pinoutsbelow
JU1 (upper pins)
Install to connect sleeve of all 1/4” and mini jacks to StudioHub+ RJ45 shield
JU1 (lower pins)
Install to connect sleeve of all 1/4” and mini jacks to StudioHub+ RJ45 power ground
2StereoStudioHub+RJ45(s)inparallel
+1 (615) 763-3033 • www.studiohub.com
21
Revised 01-02-13
ASSEMBLY 12013
FOUR SELECT BOARDSTUDIOHUB+
J4J3 J5J2J1
SW1
JU8JU7JU6JU5JU4JU3JU2JU1
(Obsolete Part) SH-4SW StudioHub+ 4 Source Switcher Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
StereoStudioHub+RJ45
Jumpers JU1-JU8 tie +15volt and –15volt from input RJ45(s) to the output RJ45 J5
JU1 –15voltsinput1JU2 +15voltsinput1JU3 –15voltsinput2JU4 +15voltsinput2JU5 –15voltsinput3JU6 +15voltsinput3JU7 –15voltsinput4JU8 +15voltsinput4
1 2 3 4
input1 input2 input3 input4 output
Inputselects
Note:
This part obsolete as of September 2012.
Replaced by active modelSH-4SWA
+1 (615) 763-3033 • www.studiohub.com
22
Revised 4-21-10
ASSEMBLY 12009
STUD
IOHU
B+ B
REAK
OUT
+15V +15V
-15V
+15V-15V
-15V
SHIELD
SHIELDSHIELD
JU1
JU6JU4
JU9JU8
JU3JU2
JU7
JU5
R5R3
J1
R6R4
J3
R2R1
J2
Part # ADAPT-BO StudioHub+ Breakout Adapter(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
These internal buses and jumpers allow +15volts, –15volts and shield to be connected from the two studioHub+ RJ45(s) and the termi-nal block. Acircuitpathrequiresatleasttwojumpers.
JU1installtotieterminalblockshieldtointernalshieldbus.
JU2 installtotieterminalblock–15voltstointernal–15voltbus.
JU3 installtotieterminalblock+15voltstointernal+15voltbus.
JU4 installtotieStudioHub+RJ45J2+15voltstointernal+15voltbus.
JU5 installtotieStudioHub+RJ45J2–15voltstointernal–15voltbus.
JU6 installtotieStudioHub+RJ45J3+15voltstointernal+15voltbus.
JU7 installtotieStudioHub+RJ45J3–15voltstointernal–15voltbus.
JU8 installtotieStudioHub+RJ45J2shieldtointernalshieldbus.
JU9 installtotieStudioHub+RJ45J3shieldtointernalshieldbus.
2StudioHub+RJ45withpinsbelowinparallel
1.Left+orAES/EBU+2.Left–orAES/EBU–3.Right+6.Right–4.PowerGround5.Future
+1 (615) 763-3033 • www.studiohub.com
Revised 3-30-11
23Part # ADAPT-GPI StudioHub+ Breakout Adapter
(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
STUD
IOHU
B+ A
DAPT
-GPI
J3
J1J2
• • • • • • • • • • • • • • • •
RJ-45 #1 (J1)Pins 1-8
RJ-45 #2 (J2)Pins 1-8
8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1RJ-45 ADAPT-GPI Pin Out for Wheatstone BLade GPIORJ-45 Pin1- Audio Ground
RJ-45 Pin2- Logic 7 In/Out
RJ-45 Pin3- Logic 8 In/Out
RJ-45 Pin4- Logic 9 In/Out
RJ-45 Pin5- Logic 10 In/Out
RJ-45 Pin6- Logic 11 In/Out
RJ-45 Pin7- Logic 12 In/Out
RJ-45 Pin8- +5V Digital
+1 (615) 763-3033 • www.studiohub.com
Revised 01-02-13
24Part # PS-CUBE StudioHub+ “DC-Link” Power Inserter
(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
J1 J2 J3 J4
J7 J8 J9 J10
J5
J6
R1R2
R3 R4 R5 R6 R7R8
Ch. 1Aud In
Ch. 2Aud In
Ch. 3Aud In
Ch. 4Aud In
Ch. 1Aud OutPwr Out
Ch. 2Aud OutPwr Out
Ch. 3Aud OutPwr Out
Ch. 4Aud OutPwr Out
+15V-15VG
n/c +15V-15VG
n/cPowerSupply+/-15vIn(or)Out.Maxpowerprovided3amps.
PowerSupply+/-15vIn(or)OutMaxpowerprovided3amps.
PS-WW Cube Power Connector. AllowsP/NPS-WWCubeorPS-WWUCubedesktoppowersupplytoprovidepower.Maxpowerprovided400ma.
Loop-Thru Power Connector. PowersupplycableP/N11516(1ft.)required.Contactthefactorytoacquireatnochargeifneeded.
Notes:Powerisaddedtoaudioconnectionsandavailableonthe4outputRJ-45’s(J1-J4).Thefourstereoaudiofeedsarekeptseperatedandisolated.
Channelsareindependent,isolatedandindependentlyfusedwithselfresettingthermalfuses.
Powered-Side Feed to Devices
Non-Powered Input Side
PS-EXTU Power Connector. AllowsP/NPS-EXTUwall-toppowersupplytoprovidepower.Maxpowerprovided3amps.
+1 (615) 763-3033 • www.studiohub.com
Tomakeinputsmonosetbothjumperstolowerposition
JU1PWR
LOGIC OUTPUT
JU2
I/O B I/O A I/O 4 I/O 3 I/O 2 I/O 1
J5 J7J6
J8
JU12JU11 JU10JU9JU8JU7JU6JU5JU4JU5
J3
(I/O A & I/O B are in parallel)
1 2 3 4 G
1 2 3 4 G
DaisyChain
PGMONLY
25
Revised 07-22-15 (Note-Thereareolderversionsofthisproduct.
Seewww.studiohub.com/legacy.php)
Part # SH-4SWSS StudioHub+ 4 Source Switcher Panel
Shielding Jumpers:JU1 –inserttoconnectpowergroundtochassisgroundJU2 –inserttoconnectpowergroundtoshield
Mono/Stereo Jumpers JU5-JU12:Tomakeinputsstereosetbothjumperstoupperposition
1 2 3 4Stereo
Mono
StudioHub+ 4 Source Switcher
TheSH-4SHSSisanactivedeviceandmustbepoweredvia+/-15VDC.PowerflowsviaStudioHub+“DC-Link”ifconnectedtoanyCat-5cablewith+/-15VDCactiveonPins7&8.Or,utilizeoptionalpowersupplyispart#PS-WWUSH.
Inputselectswillbemaintainedintheeventofapowerfailure.
InputselectswitchesmayberemotecontrolledviapinsonconnectorJ4.
Theunitisfullybidirectionalandmayswitch4inputsto1outputor1inputto4outputs
Thiscircuitboardispackagedaloneforsingle1x4use,orupto4maybeinterconnectedforuptoa1x16switchingapplication.
J5 – Programing(Note-powermustbecycledformodechange)
(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
SpecialPurposeLogicOutputJ8(SpecialPROMrequired)
Supports3 SH-4SHSS
boards
Supports4 SH-4SHSS
boards
a b c4 switches
total
8 switchestotal
12 switchestotal
16 switchestotal
Supports1 SH-4SHSS
board
Supports2 SH-4SHSS
boards
a b c a b c a b c
a b c
Install C for momentary operation(default)
Remove C for holding
operation
a b c
1 +5VDC2 NC3 PulltoGround#1
4 PulltoGround#25 GND
+1 (615) 763-3033 • www.studiohub.com
26
Revised 05-06-09
3 2 1
Part # SH-MIC StudioHub+ Mic Preamp Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
StudioHub+RJ45Outputandpowerin.Outputappearsonbothleft(1&2)andright(3&6)connectorpins
Directpowerinput+/-15voltsDC
PowerLED XLRMicrophoneinput
JU2
XLR pin 1 select
Install to connect XLR pin 1 to RJ-45 shield.
Install to connect XLR pin 1 to power ground & J1 pin 3
JU3
Phantom Power
Off
On (+15 Volts)
JU1 Gain
26dB
46dB
66dB
OutputAudioOutput+
Output–
PowerG
round
+1 (615) 763-3033 • www.studiohub.com
27
11-23-16
JU1 JU2
JU5
JU12
JU8JU10
JU9
JU11
JU7
JU13
JU3JU6
JU4
10 9 8 7 6 5 4 3 2 1
Part # SH-MICPTTPLUS StudioHub+ Mic Preamp Panel with selectable mic preamplification and push-to-talk logic
(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
JU11
Remote Barrier Strip
Directpowerinput+/-15voltsDC
XLRMicrophoneInput
JU9
Push OnPush Off
Power Up with
Audio Off
JU9
Power Up with
Audio On
A A
B
JU10
A
AB
B
B
JU11
Push To Talk
JU10
A
AB
B JU11
Push To Mute
JU10AB
Push On/Push Off Jumper Settings
Mono(Pins 1, 2)
Dual Mono(Pins 1, 2, & 3, 6)
JU1 JU1
Dual Mono Jumper Settings
JU2 JU2
No Connect No Chassis Gnd
To Chassis Gnd
To DC Gnd
To RJ-45 Shield
JU4
JU4
JU4
JU6
JU6
A
A
A
B
B
B
XLR Pin 1 Ground Jumper Settings
Pre Amp Out Pre Amp In
JU3
JU5
A
A
B
B
Mic Pre In/Out Jumper Settings
JU12
JU13
A B
JU3
JU5
A
A
B
B
JU12
JU13
Off +15VDC
JU8A B
Phantom Voltage Settings
JU8
26dB 46dB 66dB
JU7AB
Mic Sensitivity Settings
JU7 JU7A AB B
Push-To-TalkSwitch
StudioHub+RJ-45Output
XLRMicrophoneOutput
• Push-To-Talk Logic• XLR Pin 1 Grounding• Dual Mono Send• Power-Up State
• Phantom Voltage• Mic Gain• Mic Pre In/Out
Set Programming Jumpers For:
Pin 1 Audio On/Off Input (pull to Gnd)Pin 2 Relay n.o. (audio not muted)Pin 3 Relay n.c. (audio muted)Pin 4 Relay CommonPin 5 Audio Output +Pin 6 Audio Output -Pin 7 Chassis GroundPin 8 GroundPin 9 -15VDCPin 10 +15VDC
A B
A
B
A B A B
A B
+1 (615) 763-3033 • www.studiohub.com
28
Revised 11-16-16
Part # SH-MICPTT StudioHub+ Mic Preamp w/PTT Panel Also Available with no preamplification Part # SH-MICPTTPAS StudioHub+ Mic Connector w/PTT Panel
(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
JU1 & JU2
Isolated dry N. O. switch contacts JU4
Install to connect XLR pin 1 to chassis ground
JU1 Gain
26dB 46dB 66dB
JU2 XLR pin 1 select Install to connect XLR pin 1 to shield ground
Install to connect XLR pin 1 to power ground
Install jumper to defeat push to talk (on/off switching of mic output) Pushtotalk
Note:SpecifyonorderPushOn/PushOfformomentaryoperation
Switch“pushed”LED
JU3
Phantom Power Off On (+15 volts)
StudioHub+RJ45Outputandpowerin.Outputappearsonbothleft(1&2)andright(3&6)connectorpins
Outputaudioprovidedonbarrierstrip
Directpowerinput+/-15voltsDC
Output+
Output–
ShieldGround
XLRMicrophoneinput
Note: This part obsolete as of November 2016.
Replaced by active model SH-MICPTT
+1 (615) 763-3033 • www.studiohub.com
29
Revised 11-23-16 (Note-Thereareolderversionsofthisproduct.
Seewww.studiohub.com/legacy.php)
JU1
JU2
JU3
J3
J1 J2
J5
Part # SH-HPB StudioHub+ Headphone Amplifier Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
2StudioHub+RJ45inputandpoweronconnectorsinparallel
Directpowerinput+/-15voltsDC
BluePowerLED
Headphonelevel 1/4”headphonejack
JU1 Install to connect shield ground to power ground
Gain Jumper Settings (added 3/17)
1/8”(mini)headphonejack
JU2
JU3
17.3dB 7.4dB Gain Gain
+1 (615) 763-3033 • www.studiohub.com
Gain Jumper Settings (added 3/17)
JU2
JU3
17.3dB 7.4dB Gain Gain
Revised 11-23-16
JU1
JU2 JU3
J1
J3 J4
30Part # SH-HPDUAL StudioHub+ Headphone Amplifier Dual Plate
(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
J2TwoStudioHub+RJ45inputandpoweronconnectorsinparallel
J1 Directpowerinput+/-15voltsDC
PowerLED
HeadphonelevelHPAMP#1
HeadphonelevelHPAMP#2
1/4”headphonejackHPAMP#2
JU1 Install to connect shield ground to power ground
1/4”headphonejackHPAMP#1
StudioHub+ Heaphone Amplifier Dual Output Version
RJ-45 input jacks remain in parallel (there is only 1 input.)
Each output is isolated and at full power (with separate output amplifier chips.)
Current consumption is 100ma. All other specifications are identical to single (SH-HP) model.
30+1 (615) 763-3033 • www.studiohub.com
31
Revised 4-21-10
Part # SH-LEVEL StudioHub+ Monitor Level Control Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
StereoStudioHub+RJ45(s)stereooutputandpowerin
StereoStudioHub+RJ45(s)monooutputandpowerin
LevelPowerLED
2StudioHub+RJ45inputandpowerinconnectorsinparallel
Directpowerinput+/-15voltsDC
JU1
Install to connect shield ground and power ground
JU2
Install to connect shield ground and chassis ground
JU9, JU10
2 mute control connectors in parallel. Short the pins on either connector together for mute
JU3, JU4 gain select
Unity - no jumper
+10dB
+20dB
Audioandpowerinputprovidedonbarrierstrip
+1 (615) 763-3033 • www.studiohub.com
32
Revised 4-21-10
2 StudioHub+ RJ45 Input and power in connectors in parallel
JU1 Install to connect shield ground to power ground
JU2 Install to connect shield ground to chassis ground
JU4, JU5 Gain Straps Unity +10dB +20dB Gain
JU7 Mono - Stereo jumper Stereo operation
Mono operation
Left output is a mix of left and right inputs. Right output is muted
StudioHub+ Monitor Amp PanelPart # SH-AMP w/o Speaker
Part # SH-AMPSPKR w/Speaker
(Accessory Speaker) StudioHub+ Speaker Part # SH-SPKR
(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
JU6 Mute Short these pins together to mute
J7 Left speaker
J8 Right speaker
JU3 Install for stereo operation
JU6 and JU8 Power limit
Full power
Medium power
Low powerSignalPresentLED
Levelcontrol
Directpowerin+/-15voltsDC
SpeakerOutputs
Left
Ground
Ground
Right
+1 (615) 763-3033 • www.studiohub.com
StudioHub+ Amp w/Headphone Part # SH-AMPHPN
StudioHub+ Speaker Part # SH-SPKR
Revised 8-02-17
33
JU1
J2
J1
J3
JU1
Install to connect RJ-45 power ground to chassis ground
J3 Speaker out (floating output - DO NOT GROUND)
16” MTE connector
J1 2 StudioHub+ RJ45 Input and power in connectors in parallel
Power LED
Level control
1/4” Headphone Output 1/8” Headphone Output (both connectors mute speaker output)
}in parallel
(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
J2 Direct power input +/- 15 volts DC
+1 (615) 763-3033 • www.studiohub.com
34
Revised 4-21-10
Part # SH-VUV Dual VU Meter Panel (Vertical)
Part # SH-VUH Dual VU Meter Panel (Horizontal)(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
JU3
Top row/left row LED input select.
Left input
Right input
JU1
Install to connect shield ground to power ground
JU2
Install to connect shield ground to chassis ground
2StudioHub+RJ45Inputandpowerinconnectorsinparallel
Bottomrow/rightrowLEDlevelcontrol
Toprow/rightrowLEDlevelcontrol
Directpowerinput+/-15voltsDC
JU4 Bottom row/right row LED input select
Right input
Left input
+1 (615) 763-3033 • www.studiohub.com
35
Revised 4-21-10
No jumper for unity gain normal for +4dBu applications
+10dB gain
+20dB gain
Part # SH-MIXER StudioHub+ 3 Mixer Panel (Input Board)(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
StudioHub+RJ45input1andpowerin
StereoStudioHub+RJ45input2andpowerin
GainStraps(pre-fader)
JU3,JU4Input1
JU5,JU6Input2
JU7,JU8Input3
Directpowerinput+/-15voltsDC
StudioHub+RJ45Input3andpowerin
JU1
Install to connect shield ground to power ground
JU2
Install to connect shield ground to chassis ground
+1 (615) 763-3033 • www.studiohub.com
36
Revised 4-21-10
ASSE
MBL
Y ST
AND
ALO
NE 1
2103
A
ASSE
MBL
Y ST
UDIO
HUB+
121
02A
STUDIOHUB+ 3 MIXER OUTPUT
J5J6
J8J7
C17
C16
C18
C19
C7C6
C5C4
U1
U3
U5
U2
U6
U4
J10
J9
J4
C2
C1
C3
J2J3
J1
D2D3
D1D4
C20
R1
C8 C12
R14
R9
R5
R10
R6
C22
R3
C10
C14
C21
R13
R2
C9 C13
R19
R16
R11
R8R7
R18
R17
C23
R15
R12
R4
C11
C15
Part # SH-MIXER StudioHub+ 3 Mixer Panel (Output Board)(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
StudioHub+RJ45mixminusoutput.Mixofinputs1and2only.Alsopowerin
Inpu
t1m
ixle
vel
Inpu
t2m
ixle
vel
Inpu
t3m
ixle
vel
StudioHub+RJ45mainoutput.Mixofinputs1,2and3.Alsopowerin
+1 (615) 763-3033 • www.studiohub.com
37
Revised 4-21-10
Part # SH-LCDV StudioHub+ Vertical LCD Controller PanelPart # SH-LCDH StudioHub+ Horizintal LCD Controller Panel
(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
JU1
Install to connect shield ground to chassis ground
JU2
Install to connect shield ground to power ground
JU3
Install/remove to reverse direction of rotary encoder
StudioHub+RJ45datainput,dataoutputandpowerin.
Directpowerinput
+/-15voltsDC
ThisboardmustbeusedinconjunctionwiththeLCDdisplayboard.
LCD DISPLAY BOARD
STUDIOHUB+
ASSEMBLY 12145A
S1C1
S2
C3
C2
ThisboardtobeusedinconjunctionwiththeLCDmicroboard
InterfacePin-Outs
RJ-45Pin-Outs Function1 TxD+2 TxD-3 RxD+6 RxD-8 +15volt4 ground
+1 (615) 763-3033 • www.studiohub.com
38
Revised 4-21-10
Part # SH-DUALMATCH StudioHub+ In/Out Balanced Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
JU3
Install to connect shield ground to chassis ground
J3 Direct power input +/- 15 volts DC
JU1 and JU2
(install both the same)
Board power from J5
Board power from J4
JU4
Install to connect shield ground to power ground
Left Right Left RightIHFUnbalancedInput IHFUnbalancedOutput
PowerLED
RightLevel
LetLevel
RightLevel
LetLevel
BalancedOutput
andPowerIn
BalancedInputand
PowerIn
Audioin/outandpowerinputprovidedonRJ-45’s
+1 (615) 763-3033 • www.studiohub.com
39
Created 9-28-11
Part # SH-MATCHPANEL StudioHub+ In/Out Balanced Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
J1 Direct power input +/- 15 volts DC
JU1
Install to connect shield ground to chassis ground
1/8”(mini)TRSPhoneIHF
UnbalancedInput
Left&RightRCAIHF
UnbalancedInput
1/8”(mini)TRSPhoneIHFUnbalancedOutput
Left&RightRCAIHFUnbalancedOutput
PowerLED
RightLevel
LetLevel
RightLevel
LetLevel
BalancedOutput
andPower
BalancedInputand
Power
AudioinandoutandStudioHub+“DC-Link”+/-15VDCpowerprovidedonRJ-45’s
+1 (615) 763-3033 • www.studiohub.com
40
J2 1
2
3
4
5JU1
Created 9-13-17
Part # SH-ONOFFCOUGH StudioHub+ On/Off/Cough Panel(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
J2 Direct power input +15VDC (-15VDC not used)
JU1 Install to connect mic ground to chassis ground
J1 Connect Pins 4 & 5 across mixer mic input to mute audio for ON/OFF/COUGH effect.
ON/OFF/COUGH Control Panel
For use when controlling microphone when connected to music mixers (non-broadcast style consoles without GPIO control).
ON/OFF buttons will switch the mic on/off and the “COUGH” button will momentarily mute the mic audio. All buttons are LED lit to indicate status.
The panel must be provided with +15VDC. RJ-45 (StudioHub+) and barrier strip I/O connections are provided as well as +15VDC in parallel with the ON lamp to close a remote relay for speaker MUTE control.
Ground
ON (+15VDC when ON button illuminated) (use to activate muting relay)MIC Shield (in parallel with RJ-45 Shield)
MIC + (in parallel with RJ-45 Pins 1 & 3)
MIC - (in parallel with RJ-45 Pins 2 & 6)
Pin-1 – MIC +Pin-2 – MIC -Pin-3 – MIC + (in parallel with Pin-1)Pin-4 – GroundPin-5 – not usedPin-6 – MIC - (in parallel with Pin-2)Pin-7 – not usedPin-8 – +15VDC
Recommended Accessory:Use the StudioHub+ CABLE-XLRMF (or ADAPT-XLRMF) to loop the Mic signal through the panel.
RJ-45 Pin-Out
+1 (615) 763-3033 • www.studiohub.com
(856) 467-8000 • Fax (856) 467-3044 • www.studiohub.com
Warranty RadioSystems,Inc.,warrantsthisequipmenttobefreefromdefectsinmaterialsandworkmanshipforaperiodofone(1)year.
Thiswarrantyextendstofirstusersoftheproductandfutureownerswhopurchasetheproductwithinthewarrantyperiod.
Thetermsofthiswarrantyarenullandvoidifthisproductisstoredoroperatedinanenvironmentnotconducivetoelectronicequipment,orshowssignsofmisuseormodificationswhichaffecttheproperfunctioningoftheproduct.Thiswarrantydoesnotapplytodamagecausedbyfire,smoke,flood,lightning,oractsofnatureandphysicalabuse.
RadioSystems,Inc.,anditsassociatedcompanies,authorizeddistributors,andpersonnelarenotliableforlossofrevenuesorotherdamages,oreffectstothebroadcastsignalqualityorcoveragewhichmayresultfromthefromtheimproperfunctioningofthisproduct.
Repair Policy Technicalassistanceisavailableatanytime,atnocharge,byphoneorcorrespondence.
Duringthewarrantyperiod,therewillbenochargeforpartsorservicemadetounitswhichshownosignofmisusebycustomerorlightningcauseddamage.ThecustomerisresponsibleforthecostofshippingtheirunitbacktoRadioSystemsforrepair.
Duringthewarrantyperiod,shipmentofsmallpartsandassembliesmayalsobemadeatachargetotheuser.Emergencyshipmentsofreplacementpartsandcircuitswillbemadeattheuser’srequestforanextrashippingandservicecharge.ChargeableserviceswillbemadeCODoronNet-30daytermstouserswithestablishedaccounts.
Duringthewarrantyperiod,fullcreditorreturnofCODcharges(lessanyserviceandexpeditedshippingcharges)willbemadetouserswhoreturnthedefectivepartsorcircuitswithin30days,ifthedamageiscoveredunderthetermsofthewarranty.
Return Instructions ContactRadioSystemsforareturnauthorizationnumber.Packallitemscarefullyandshipprepaid,viaUPSinsured,to: RadioSystems,Inc.
Attn:R.A.#__________ 601HeronDrive LoganTownship,NewJersey08085-1741
Encloseanotewhichincludesyourname,company,phonenumber,theserialnumber,returnaddress(noboxnumbers),andacompletedescriptionoftheproblem.
+1 (615) 763-3033 • www.studiohub.com
601 Heron Drive • Logan Township, New Jersey 08085 • (856) 467-8000 • Fax (856) 467-3044
www.studiohub.com • www.radiosystems.com
Revised 08-02-2017
128 Holiday CT STE 118 • Franklin, TN 37067 +1 (615) 763-3033 • [email protected]
www.angryaudio.com • www.studiohub.com