small engine parts & accessories chainsaw chainsaw … · small engine parts & accessories...

Small Engine Parts & AccessoriesCLUTCHESCLUTCHES

C C

646-149 Husqvarna#530 01 49-49

Clutch AssemblyFor chain saw models: 137.Size: 2.33” OD X .410” Thick.

646-150 Husqvarna#501 45 54-03

Clutch AssemblyFor chain saw models: 50, 51, 55, 54, 254, 257 and 261.Size: 2.610” OD X 0.453” Thick.

646-151 Husqvarna#537 11 05-03

Clutch AssemblyFor chain saw models: 340, 345, 346,350, 353, 445, 450, 455, 460 and 461.Size: 2.675 OD X 0.400” Thick.

646-113 Husqvarna#501 77 85-01

Clutch Assembly Fits chain saw models: 61, 66, 266, 266XP, 268 and 272; also fi ts Jonsereds chain saw models: 625, 630 and 670. Size: 3.057” OD X 0.512” Thick.(Also see 646-153 newer style)

646-153 Husqvarna#501 77 85-01501 77 85-02503 52 79-01503 74 44-02

Clutch AssemblyFor chain saw models: 61, (after Serial# 602497),66, 266 (affter serial# 6051313), 268 and 272;Concrete / Cut Quik Saw models: K750 and K760.Fits Jonsereds chain saw models: 625, 630 and 670.Size: 3.057” OD X 0.475” Thick.Thread Size: 10mm X 1 Left Hand Thread.(Fits our 590-149 crankshaft assembly)

646-154 Husqvarna#503 74 44-01

Clutch AssemblyFor chain saw models: 362, 365, 371, 372, 385, 390 and 575. Size: 3.057” OD X 0.471” Thick.

646-155 Husqvarna#503 70 15-02

Clutch AssemblyFor chain saw models:281, 288 & 395 (after Serial# 003900001) Size: 3.045” OD X 0.542” Thick.

(While Quantities Last)

CHAINSAW CHAINSAW continued

646-110 McCulloch

Clutch AssemblyFits McCulloch chainsaw model: 1010. Size: 3-1/4″ OD

646-129 Poulan# 93919 Weedeater#530-069195 530-093919

Clutch Fits many small Poulan chain saw and Poulan / WeedeaterTrimmer models. Size: 2-3/8” OD, steel washer included.

646-260 Stihl# 4119-160-2001

Muffler / ExhaustFits Stihl trimmer models:FS160, FS180, FS220 and FS280.Size: 2-5/16” OD, comes with two bushings.Bushings measure: 6mm ID X 10mm OD.

646-111 Stihl#1123-160-20011123-160-2050

Clutch AssemblyFor chain saw models: 017, 018,019 T, 021, 023, 025, MS170, MS180,MS190 T, MS191 T, MS210, MS230,MS231, MS241, MS250 and MS251.Size: 2-1/2” OD.

646-112 Stihl# 1121-160-2051

Clutch Assembly Fits chain saw models: 024, 026,MS240, MS260, MS261, MS270,MS271, MS280, MS291.Size: 2.675” OD X 0.403” Thick. 19mm nut attached to this clutch for removal.

646-114 Stihl#1127-160-20001127-160-2002 1127-160-2050 1127-160-2051

Clutch Assembly Fits 029, 034, 039, MS290,MS310, MS340, MS390.Size: 2.928” OD X 0.403” Thick. 19mm nut attached to this clutch for removal.

646-117 Stihl #1125-165-2052

Clutch Assembly Fits Stihl chain saw models: 036 and MS360. Size: 2.894″ OD X 0.390″ Thick. 19mm nut attached to this clutch for removal.



18-01


C C

646-118 Stihl #1113-160-2010

Clutch AssemblyFits Stihl chain saw model: 031, 032 and 041.

Size: 2-21/32″ OD

646-120 Stihl #1119-160-2000

Clutch AssemblyFits Stihl chain saw model: 038 series.

Size: 2-3/4″ OD X 9/16″ ID X 5/8″ Overall HT

646-124 Stihl #1128-160-2004

Clutch Assembly Fits Stihl chain saw models: 044, 046, MS440, MS460, MS341 and MS361.

Size: 2.916″ OD X 0.392″ Thick. 19mm nut attached to this clutch for removal.

646-122 Stihl #1111-160-2003

Clutch Assembly Fits Stihl chain saw models: 051 and 075.

Size: 3-5/16″ OD. Note: Not exactly as shown, clutch is no longer lined with asbestos

646-119 Stihl # 1122-160-2005

Clutch Assembly Fits Stihl chain saw models: 064, 066, MS640 and MS660.

Size: 3.140″ OD X 0.460″ Thick.19mm nut attached to this clutch for removal.

646-116 Stihl #1108-160-1501 1108-160-2001 1108-160-2002

Clutch AssemblyFits Stihl chain saw model: 08S and Cut Quik models:TS-350 and TS-360.

Size: 2-19/32″ OD X 1/2″ bore X 3/16″ keyway.

646-123 Stihl #1125-160-2005 1125-160-2006

Clutch Assembly Fits Stihl Concrete / Cut Quiksaw model: TS400.

Size: 2.885″ OD

Part# ToothCount

Chain Size

Bore OD Keyway

255-026 12 #35 1” 4-1/4” 1/4”(built in)

255-059 10 #40#41

1” 4-1/4” 1/4”(built in)

Three sintered metal shoes engage at 2000 RPM. Stainless steel garter spring, works Clockwise or counter-Clockwise, oilite bearing for long life. Works in oil, dirt and water with proper maintenance. (For 2-1/2 thru 8 Hp engine applications) MADE BY COMET - For outboard mounting only (sprocket away from engine)

COMET continued - Belt Drive

Part# Belt Bore PullyDia.

OD Keyway

255-067 A or Bsec. belt

5/8” 3” 4-1/4” 3/16”


1” 3” 4-1/4” 1/4”

Two sintered metal shoes engage at 2000 RPM. MADE BY COMET. Fits 2-1/2 thru 8 Hp engines. Non-directional clutch (inboard or outboard).All comet pulley clutches are *While Quantities Last*

CHAINSAW continued CENTRIFUGAL - COMET

18-02


C C

Part# ToothCount

Chain Size

Bore OD Keyway

255-109 11 #35 5/8” 4-1/4” 3/16”

255-117 10 #40#41

5/8” 4-1/4” 3/16”

255-125 12 #35 3/4” 4-1/4” 3/16”

255-133 10 #40#41

3/4” 4-1/4” 3/16”

Part# Belt Bore PullyDia.

OD Keyway


5/8” 3-1/4” 4-1/4” 3/16”


3/4” 3-1/4” 4-1/4” 3/16”

Six sintered metal shoes engage at 2000 RPM. Stainless steel garter spring, works Clockwise or counter-Clockwise, oilite bearing for long life. Works in oil, dirt and water with proper maintenance. (For 2-1/2 thru 8 Hp engine applications) MADE BY MAX TORQUE

Part# ID Teeth Chain Size

255-141 3/4” 11 #35

255-158 7/8” 12 #35

255-166 3/4” 10 #41

255-174 7/8” 10 #41

Part# ID OD

255-182 3/4” 7/8”

255-190 7/8” 1”

260-265 3/16” 3/4”

255-714AYP# 106316X AYP# 917063 / 109550XBobcat# 188018 / 188019Exmark# 1543259 Exmark# 543259Exmark# 1551054Ferris# 1521083Great Dane# D18000 Husqvarna# 532 91 70-63Snapper# 1-7063 / 7017063Warner# 5215-14

Size: 1″ ID X 2-7/8″ HT, Pulley diameter: 6″ ODUses 5/8″ belt.

255-711Ariens# 36018 / 03601800Ayp# 145028Dixon# 145028 / 532145028Gravely# 03601800 Husqvarna# 532 14 50-28 Simplicity# 1686882 / SMSimplicity# 1708536 / SMSnapper# 1686882 / SMWarner# 5217-2 Warner# 5217-46

Size: 1″ ID X 3″ HT, Pulley diameter: 5.375″ ODUses a 1/2″ belt. Rotation: Counter Clockwise. Fits ARIENS models: EZR, LT, Sierra and YT series mowers; Fits CRAFTSMAN models: CO, CT, DB, DPR, PP, PR, QP, RE, RK, YG and YP series; Fits GRAVELY models: EZR, LT, Sierra and YT series mowers; Fits HUSQVARNA models: GTVH200, 1998-2010, GTVH205, 1999-2010, YTH1342XP, YTH1542XPA, YTH1542XBP, YTH1542XPC, YTH542XPD, YTH1542XPE, YTH1542XPF, YTH1542XPG, YTH2046A, YTH2046B, YTKH1542XPA, YTKH1542XPB and YTKH1542X-PC; Fits SIMPLICITY models: 400, Coronet, Regent and ZT series; Fits SNAPPER models: most RT1330 and RT1330E.

255-713Ariens# 30908 / 03090800Cub Cadet# WDC38410 Grasshopper# 388766 Grasshopper# 604182Gravely# 30908 / 03090800Jacobsen# C38410MTD# C38410Toro / Wheel Horse# 93-3160 Warner# 52-1552Warner# 5215-62Warner# 5215-120

Size: 1-1/8″ ID X 3-3/4″ HT, Double Pulley diameter: 4-13/16″ OD Uses a 1/2″ belt. Rotation: ClockwiseFits ARIENS models: 931037, 931038, 931302, 931303 and 987104; Fits GRASSHOPPER models: 718K and 720K; Fits GRAVELY models: 931037, 931038, 931302, 931303 and 987104; Fits TORO models: 74140 and Proline 724-Z, Serial No. 590001-699999.

ELECTRIC PTO CLUTCHESCENTRIFUGAL - MAX TORQUE

18-03


C C

255-710

AYP# 108218X 142600 / 137140Cub Cadet# 717-0949717-1434 / 917-0949917-1434 Husqvarna# 532 10 82-18 Husqvarna# 532 14 26-00 MTD# 717-1434Warner# 5215-51 Warner# 5219-64

Size: 1″ ID keyed hub X 4.175 HT, Pulley diameter:5.304″ OD. Uses 1/2″ belt. ALL ELECTRIC PTO CLUTCHES WILL NOT BE WARRANTIED IF NOT INSTALLED BY A SERVICING DEALER.

255-712

Ariens# 03643100 Ariens# 36431AYP# 160889Cub Cadet# 717-1459Cub Cadet# 917-1459 Dixon# 3579Husqvarna# 532 16 08-89 / 99John Deere# AM119683 MTD# 1772388 / 717-1459MTD# 917-1459 Snapper# 53739 / 53740 Snapper# 7053740 / 7653740Swisher# 688EC Troy Bilt# 1772388 / 9171459 Woods# 03643100Warner# 5217-35Warner# 5217-9 / 5217-6

Size: 1″ ID X 3″ HT, Pulley diameter: 5.375″ ODUses 1/2″ or 5/8″ belt. Rotation: Counter Clockwise. Fits Ariens models EZR 1540, 1648 and 1742; John Deere model: STX-36; Troy Bilt models: LTX 13095, 13102-13105 & 13123 tractors as well as other makes & models. Uses A or B 1/2 & 5/8″ belt

QUICK TIPReplacing Electric PTO Clutches

- Use Grade 5 or Grade 8 bolt only! Minimum torque:- 7/16″ UNF bolt is 50 foot pounds / 67 Nm- 3/8″ UNF bolt is 31 foot pounds / 42 Nm- M10 X 1.5 bolt is 35 foot pounds / 48 Nm

WARNING - Anything less than required mounting torque will result in clutch failure.

255-715AYP# 102603 / 109580Bobcat# 1522040 / 2188151 Case# 2188151Dixon# 102603 / 109580Dixon# 539102603Dixon# 539109580Exmark# 1030664 Exmark# 633099 / 1-633099 Exmark# 631645 / 1-631645Ferris# 1522040 Husqvarna# 102603Husqvarna# 539 10 26-03 / 539 10 95-80Kees# 102603 Warner# 5218-5 / Warner# 5218-259

Size: 1-1/8″ ID X 3-1/4″ HT, Pulley diameter: 6-5/16″ OD Uses 5/8″ belt.Fits BOBCAT models: ZT200 and ZT331 series; Fits EXMARK models: Lazer Z, Serial No. 159,999 and lower, 25 HP; Fits HUSQVARNA models: ZTH5223A and ZTH5225A, 2000-2006; Fits KEES models: ZKH52220, ZKH52221, ZKH52222, ZKH52223, ZKH52233, ZKH52250 and ZKH52251.

ALL ELECTRIC PTO CLUTCHES WILL NOT BE WARRANTIED IF NOT INSTALLED BY A SERVICING DEALER.

255-716AYP# 138412 / 326108Cub Cadet# 138412 Murray# 326108Murray# 326108MA Warner# 5215-53 Warner# 5215-55

Size: 1″ ID X 3-5/8″ HT, Pulley diameter: 5-3/8″ OD Uses 1/2″ belt.Found on CUB CADET models: 2130 and 2135.

255-717

Ariens# 00554300Ariens# 00574100 Ariens# 55430 / 554300Ariens# 574100Case# C375569 Grasshopper# 388762Grasshopper# 604180 Gravely# 574100 Gravely# 0054300 / 00554300Gravely# 00574100 / 554300Woods# 70903 / 73113 Woods# 388762 / 604180Woods# 73559 / 073559Warner# 5218-27

Size: 1″ ID X 3-13/16″ HT, Double Pulley diameter: 4-7/8″ OD Uses a 1/2″ belt.Fits WOODS models: 1850, 1855, 1860,5120-5140, 5160-5180, 6140-6160 and 6170-6180.

ELECTRIC PTO CLUTCHES ELECTRIC PTO CLUTCHES

18-04


C C

255-718Ariens# 050236Ariens# 3450500 / 03450500Dixie Chopper# 50300 Exmark# 116277Gravely# 050236 / 03450500Snapper# 7-9197Snapper# 7-9446Snapper# 7079197Snapper# 7079446 / 7079446YP Toro / Wheel Horse# 116277 Warner# 5210-34 / 5210-50 / 5215-88

Size: 1″ ID, Pulley diameter: 5-1/4″ ODUses a 5/8″ belt.Fits ARIENS models: 934005, 934006, 934007, 934008, 934019 and 934020, HT series; 49065, 50267, 52271, 52628, 52626, 51385, 513386, 52627, 934010, 934011, 934012, 934013, 934014, 934016, 934017, 934018 and 934022, GEM series; Fits GRAVELY models: 934005, 934006, 934007, 934008, 934019 and 934020, HT series; 49065, 50267, 52271, 52628, 52626, 51385, 513386, 52627, 934010, 934011, 934012, 934013, 934014, 934016, 934017, 934018 and 934022, GEM series; Fits SNAPPER models: ZTR series 0-5; Fits TORO models: 612-Z, Serial No. 1000001-1999999, 616-Z and 620-Z, Serial No. 100001-599999, 616-Z, Serial No. 390000001-499999999 and Z118, Serial No. 79000001-79999999.

255-719Ariens# 092026Ariens# 9225400 / 09225400 AYP# 128711Country Clipper# E6247Dixon# 60473 / 60499Dixon# 61516 Dixon# 128711 / 539128711Exmark# 946136Gravely# 092026 / 092254 / 09225400 Husqvarna# 539128711Kees# 128711Toro / Wheel Horse# 94-6136 Warner# 5218-10 / 5218-223

Size: 1-1/8″ ID X 3-1/4″ HT, Pulley diameter: 5-3/8″ ODUses a 1/2″ or 5/8″ belt.Fits ARIENS models: Hydro Pro 300, ZTR PM 200 and PM series; Fits DIXON models: ZTR6023, ZTR7025 and ZTR7225; Fits GRAVELY models: Hydro Pro 300, ZTR PM 200 and PM series.ALL ELECTRIC PTO CLUTCHES WILL NOT BE WARRANTIED IF NOT INSTALLED BY A SERVICING DEALER.

255-721

Ariens# 00574200 Ariens# 09407700 Grasshopper# 388767 Grasshopper# 606242 Snapper# 35520 / 58925Snapper# 7058925 / YPWoods# 73558 / 74075Warner# 5218-26 / 5218-58 / 5218-257

Size: 1-1/8” ID X 3-3/8” HT, Double Pulley diameter: 4-7/8” OD. Uses a 1/2” belt. (Made by an O.E.M. supplier).

255-722

AYP# 174367Husqvarna# 532 17 43-67 Warner# 5215-134

Size: 1″ ID X 3-3/4″ HT, Pulley diameter: 6″ OD Uses a 1/2″ or 5/8″ belt.

255-724

Cub Cadet# 717-3446Cub Cadet# 917-3446MTD# 717-3446 MTD# 917-3446Warner# 5218-29

Size: 1″ ID X 3-1/2″ HT, Pulley diameter: 6″ ODUses a 5/8″ belt.

Fits Cub Cadet models: 2160, 2164, 2165, GT2521, LT2180 serial no. 326,006 and up. Mfg date B037G3 and after.

255-727

Encore# 523370Warner# 5218-17

Size: 1-1/8″ ID X 3-1/2″ HT, Pulley diameter: 6″OD.Uses a 5/8″ belt. ALL ELECTRIC PTO CLUTCHES WILL NOT BE WARRANTIED IF NOT INSTALLED BY A SERVICING DEALER.

255-359AYP# 124648X AYP# 150283 / 140923AYP# 174509 / 170056Cub Cadet# 717-3375 Cub Cadet# 717-3384Cub Cadet# 917-3375Cub Cadet# 917-3384 Husqvarna# 532 10 62-28 532 14 09-23 / 532 14 45-09 532 14 87-36 / 532 17 00-56 Warner# 5210-60 Warner# 5215-73

Size: 1-1/8″ ID X 4.825″ HT, Pulley diameter: 5-3/8″ OD.Uses a 1/2″ belt.

Fits Husqvarna models: GTH2250 A, GTH2550 B, GTH2550 XP A and GTH2550 XP B. Replaces WARNER# 5215-73 / 5210-60, Ogura# 170056, 031016.


18-05


C C

255-725AYP# 74022Cub Cadet# 717-1708Cub Cadet# 917-1708MTD# 717-1708 MTD# 917-1708 Snapper# 14022 / 74022Snapper# 707402 / 7074022Snapper# 7074022YPTroy Bilt# 717-1708 / 917-1708 Warner# 5215-129

Size: 1″ ID X 3-1/2″ HT, Pulley diameter: 5-3/8″ ODUses a 1/2″ or 5/8” belt. Fits CUB CADET models: LT1018, LT1650, LT1800, LT1850 and LT2150; Fits MTD models: 1527, 1600, 1800, 1170, 1180, 1515 and 1517; Fits SNAPPER models: ZTR Scrambler, series 5-6, ZTR Twin Stick, series 6 and ZTR Yard Cruiser series 1-4.

255-730Ariens# 00191700 Gravely# 00191700 Warner# 5219-45

Size: 1″ ID, Pulley diameter: 6″ OD Uses a 5/8″ belt.Fits ARIENS models: 2550XL, 2552XL, 2560XL and PM34Z; GR, HR, HR, PM and ZT series; Fits GRAVELY models: 2550XL, 2552XL, 2560XL and PM34Z; GR, HR, HR, PM and ZT series.

255-12230Cub Cadet# 717-3384Cub Cadet# 717-3389 Cub Cadet# 917-3384Cub Cadet# 917-3389 MTD# 717-3389MTD# 917-3389 Warner# 5210-30 / 5215-68

Size: 1″ ID X 4.825″ HT, Pulley diameter: 6″ OD Uses a 5/8″ belt. Fits Cub Cadet models: 1440, 1641, 1782, 2182, Z42, Z48, Z48L, Z54, Z54L, 2160, 2165 and 4815 serial numbers 851,001 and above. Counter Clockwise Rotation.

255-726Cub Cadet# 717-1709Cub Cadet# 917-1709MTD# 717-1709 MTD# 917-1709Troy Bilt# 717-1709Troy Bilt# 917-1709 Warner# 5215-130

Size: 1″ ID X 4″ HT, Pulley diameter: 5-3/8″ OD Uses a 1/2″ belt.Fits MTD model# 809; Fits TROY BILT models: 14AV809H063, 14AW809H063, 14AY809P063, 14BV809H063, GT2246, GT2554, GTX2246 and GTX2654.


255-728Cub Cadet# 917-3497Jacobsen# 990947MTD# 717-3497 MTD# 917-0983Simplicity# 1703816 Snapper# 1-6343 Toro / Wheel Horse# 99-8012 Warner# 52-1033 / 52-1559

Size: 1″ ID X 3-1/2″ HT, Pulley diameter: 5.345″ OD Rotation: Counter Clockwise. Uses a 1/2″ belt.Fits BOLENS models: FST14, FST15, LR13, LT14, LT145, LT15, LT16 and LT165; Fits SIMPLICITY models: 1613G, 1615G, 1613H, 1615H, 1616H, 2614H, 2616H, Broadmoor, LT, LTG and LTH series; Fits SNAPPER models: GT180, GYT, HT, LT, RYT, YT, PL7H and PP7H series.

255-732Bobcat# 2722016Bunton# 2722016 Warner# 5219-14

Size: 1-1/8″ ID, Pulley diameter: 6″ OD Uses a 5/8″ belt.Found on BOBCAT: Zero Turn 52” and 61” walk behinds....

255-733Cub Cadet# 717-04163 Cub Cadet# 917-04163 MTD# 717-04163A MTD# 917-04163A Warner# 5217-32Warner# 5217-43

Size: 1″ ID X 4” HT, Pulley diameter: 5.923″ ODUses 1/2″ or 5/8″ belt. Fits Cub Cadet models: LT1040, LT1042, LT1045, LT1046 and LT1050. Counter Clockwise rotation.

255-735Exmark# 1030500Exmark# 103-0661 / 103-0662Exmark# 631644 / 1-631644Exmark# 631731 / 1-631731Exmark# 633098 / 1-633098Exmark# E631644 / E631731 / E633098Scag# 03-0661 / 461397Toro# 63-1644 / 63-1731 / 63-3098 / 103-0500Toro# 1030660 / 1030661 / 1030662 / 1631644Toro# 1631731 / 1633098 / 1641213 Warner# 5218-21 / Warner# 52-1825Warner# 5218-76 / Warner# 5218-293

Size: 1″ ID X 3-3/8″ HT, Pulley diameter: 6-3/8″ Uses a 5/8″ belt.Found on EXMARK models: Lazer Z, 18 thru 23HP, Kohler, Serial No. 789,999 and lower; Lazer Z, 27 thru 30HP. Kohler, Serial No. 370,000 and higher; Turf Tracer Hydro, Serial No. 320,000 and higher; Turf Tracer S, Serial No. 920,000 and higher; and Turf Tracer X, Serial No. 920,000 and higher.ALL ELECTRIC PTO CLUTCHES WILL NOT BE WARRANTIED IF NOT INSTALLED BY A SERVICING DEALER.


18-06


C C

255-734Cub Cadet# 717-04174 / A Cub Cadet# 917-04174 / AMTD# 717-04174 / A MTD# 917-04174 / A Troy Bilt# 717-04174 / ATroy Bilt$ 917-04174 / AWarner# 5219-51Warner# 5219-79

Size: 1″ ID X 4-1/4 HT, Pulley diameter: 6″ ODUses a 5/8″ belt. Counter Clockwise Rotation. Fits CUB CADET models: LT1042, LT1045, LT1046, LT1050, LTG1050, LTG1054, LTX1042, LTX1045, LTX1046, LTX1050, SLT1050, SLT1550, SLT1554, SLTX1050 and SLTX1054; Fits MTD models: 800, GT, L, LT, RTZ and SLT series; Fits TROY BILT models: Big Red GT50, GT54 and Big Red Horse series.

255-11072Cub Cadet# 01002108P Warner# 5218-14

Size: 1″ ID, Pulley diameter: 6″ ODUses a 5/8″ belt.Fits TANK models, also fi ts Lesco.

255-736Bobcat# 2721337 Bunton# 2721337 Exmark# 1030501 / 1030665 Exmark# 1631732 / 1641300 Ferris# 1521145 Grasshopper# 388740 / 604182 Hustler# 601311 / 787366 Scag# 461395 / 481530 Toro / Wheel Horse# 1030501 Warner# 5218-213Warner# 5218-65

Size: 1-1/8″ ID X 3-3/8” HT, Pulley diameter: 6.25″ OD Uses a 5/8″ belt. Fits Exmark models 1600,000 & higher. Fits Bad Boy 070-5035-00, Exmark/Toro 103-0501, Auburn 180265, Bad Boy 070-5035-00. Midmounts Excel 787366. For 25 Hp engines. Fits Exmark Lazer Z series #160,000 and higher and MS200F; for 25 Hp engines.

255-737

Exmark# 1030690 / 1653048 Exmark# 1653292 / 653292Warner# 5218-80Warner# 5218-80C

Size: 1″ ID X 3-1/4″ HT, Pulley diameter: 7-3/8″ ODUses a 5/8″ belt.Fits Exmark model: Lazer Z Hp serial numbers 260,000 and higher.ALL ELECTRIC PTO CLUTCHES WILL NOT BE WARRANTIED IF NOT INSTALLED BY A SERVICING DEALER.

255-738Ariens# 09232700 Ariens# 9232700 Gravely# 00389900 Gravely# 09232700 Gravely# 09266700 Gravely# 9266700 Great Dane# GDA10122 Wood Mizer# P604Warner# 5218-31 Warner# 5218-94

Size: 1″ ID X 3-1/4″ HT, Pulley diameter: 6″ ODUses a 1/2 or 5/8″ belt. Fits Exmark model: Lazer Z Hp serial numbers 260,000 and higher. Replaces WARNER# 5218-80 / 5218-80-C. Similar to our 255-787 - our 225-737 has a 7-3/8″ OD Pulley compared to our 255-787 with a 7-11/32″ OD Pulley.Heavy Duty version of our Part# 255-720

255-739

Cub Cadet# 717-04080 Cub Cadet# 917-04080 MTD# 717-04080MTD# 917-04080Warner# 5215-142

Size: 1″ ID, Pulley diameter: 6″ ODUses a 5/8″ belt.

255-15782

Cub Cadet#020-02160 020-02160P MTD# 020-02160MTD# 020-02160P

(Replaces Ogura: GT1-CT04 / GT1CT04)

Size: 1” ID X 3-21/32” HT, Pulley diameter: 5-5/16” OD Rotation: Counter Clockwise. Uses 1/2” or 5/8” beltsFits CUB CADET models: ENFORCER 48 and 54 Zero Turn mowers.

255-785

Cub Cadet# 7173390 Cub Cadet# 9173390 Encore# 523025 Warner# 521569

Size: 1-1/8” ID X 3-1/2” HT, Pulley diameter: 6” OD Uses a 5/8” belt. Counter Clockwise Rotation. Found on Cub Cadet 2185 tractor; also used on Encore equipment.



18-07


C C

255-11074

Toro / Wheel Horse# 105-1671 / 94-4632 Warner# 5218-33

Size: 1-1/8″ ID, Pulley diameter: 4-7/8″ ODUses a 5/8″ belt.Fits Toro models: A320 - Z325, 320 Z Master etc.

255-787Exmark# 103-0690Exmark# 65-3048 Toro / Wheel Horse# 105-3630 Warner# 5218-201Warner# 5218-215Warner# 5218-44

Size: 1″ ID X 3-1/4″ HT, Pulley diameter: 7.345″ OD Uses belt width: 5/8″. Replaces WARNER# 5218-44, 5218-201 and 5218-215.Found on Exmark models Lazer HP and Lazer; for 17 Hp Kawasaki engines; also replaces Toro# 105-3630. Note: Similar to our 255-737 but with slightly smaller pulley OD.

255-15974Exmark# 11-6298Warner# 5218-251

Size: 1” ID X 3-1/8” HT Pulley diameter: 7-1/4” ODUses 5/8” belt.

(Replaces Warner 5218-251)

Fits Exmark models: 44” Quest Zero-Turn Mower, 20HP Kawasaki (SN: 850000-919999) - Engine Group - 20HP Briggs & Stratton, 48” Quest Zero-Turn Mower, 20HP Kawasaki (SN: 850000-919999) - Engine Group - 20HP Briggs & Stratton, 52” Quest Zero-Turn Mower, 22HP Kawasaki (SN: 850000-919999) - Engine Group - 20HP Briggs & Stratton, Quest SP (SN: 850000-919999) - Engine Group - 20HP Briggs & Stratton. Fits Quest SP S/N 850,000 & up, QSP20KAS443 S/N 850,000 & up, QSP20KAS483 S/N 850,000 & up, QSP22KAS523 S/N 850,000 & up assembly.

255-701Cub Cadet# 717-3385A Cub Cadet# 917-3385A MTD# 717-3385A MTD# 917-3385A Warner# 5217-14 Warner# 5217-42

Size: 1″ ID X 3-1/2″ HT, Pulley diameter: 5.345″ OD Uses a A / B belts. Counter Clockwise rotation Fits Cub Cadet 2000 series models: 2130, 2135, 2143, 2146, 2150, 2155, 2165, 21665 and GT2542. For 38” & 42” cut decks.ALL ELECTRIC PTO CLUTCHES WILL NOT BE WARRANTIED IF NOT INSTALLED BY A SERVICING DEALER.

255-702

Fits ExmarkWarner# 5218-54

Size: 1-1/8″ ID X 3-5/16″ HT, Pulley diameter: 7.385″ Uses a 5/8″ belts. Counter Clockwise rotation.Fits Exmark mowers with larger engines and crankshafts.Note: Similar to our 255-737 but with a larger 1-1/8″ bore.

255-703Exmark# 103-0281 Exmark# 103-1364Toro / Wheel Horse# 103-0281Toro / Wheel Horse# 103-1364 Warner# 5218-73

Size: 1-1/8″ ID, Pulley diameter: 6.313″ OD. Uses a 5/8″ belt.Fits EXMARK models: Lazer Z, Kawasaki, Serial No. 260,000-369,999 and Lazer Z, liquid-cooled, Serial No. 260,000-369,999.

255-704Exmark# 603539 / 1-603539 Exmark# 1-611223Ferris# 1521823 / 5021823Scag# 461074 Scag# 481633 / 48786 Simplicity# 21823Simplicity# 5021823 / SM Snapper# 2-1823 / 2-9678Snapper# 5021823 / 7029678 / YPWarner# 5215-13 / 5215-99

(Replaces Ogura# MA-GT-EXM3XS 21)

Size: 1″ ID X 3-1/2″ HT, Pulley diameter: 6″ OD.Uses a A / B belts. Clockwise rotation Fits EXMARK models: early Turf Ranger 1800, Turf Tracer, 5-speed, Serial No. 89,999 and lower, Turf Tracer Hydro, Serial No. 70,000-129,999 and Turf Tracer Hydro, Serial No. 190,000-319,999; Fits FERRIS models: 5900027, 5900030, 5901009, 5901194, 5901012, 5901014, 5901015, BGF36K and BGF52K; Fits SCAG models: SSZ, STHM, SW and SWZ series; Fits SNAPPER models: 7080717, 7080682, 7080683, 7080685, 7080686, 7080687 and 7080695.

255-705Hustler# 781039 Hustler# 781039K Warner# 5218-110Warner# 5218-219

Size: 1-1/8″ ID X 3-5/16” HT, Pulley diameter: 6-1/4” OD. Uses both A/B belts, Rotation: Counter Clockwise. Fits Hustler models: Super Z, 52″, 60″ and 72″ decks; also found on Grasshopper model 223.ALL ELECTRIC PTO CLUTCHES WILL NOT BE WARRANTIED IF NOT INSTALLED BY A SERVICING DEALER.


18-08


C C

255-706

Exmark# 103-3132Exmark# 103-3246 Exmark# 103-4000Exmark# 103-4057Exmark# 103-5835Exmark# 103-6579 Exmark# 109-7665Exmark# 109-7673Exmark# 116-1611Toro# 1033132 / 1033246Toro# 1034000 / 1034057Toro# 1035835 / 1036579Toro# 1097665 / 1097673Toro# 1161611Warner# 5218-99Warner# 5218-168 Warner# 5218-202Warner# 5218-209

Size: 1-1/8″ ID X 3-5/16″ HT, Pulley diameter: 7-11/32″ OD. Uses a 5/8″ belt. Clockwise rotation.Fits Exmark Lazer HP / Z models; for 27 and 30 HP Kohler engines.

255-15770

Ferris# 22590Ferris# 23232Ferris# 5022590Ferris# 5023232Gravely# 03785000Simplicity# 5022590Simplicity# 5023232Simplicity# 5023232SMSnapper# 22590Snapper# 23232

(Replaces Ogura: GT2.5-FE02).

Size: 1-1/8” ID X 3” HT, Pulley diameter: 6 1/8″ OD. Uses 5/8” belt. Rotation: Counter Clockwise.Fits FERRIS, GRAVELY, SIMPLICITY and SNAPPER mowers.

255-15771

Dixie Chopper# 500144Ferris# 5100417Gravely# 04553800

(Replaces Ogura: GT1A-EH01 and 53462700)

Size: 1-1/8” ID X 3-1/4” HT, Pulley diameter: 5-15/16″ OD. Uses 1/2” or 5/8” belt. Rotation: Counter Clockwise.Fits DIXIE CHOPPER, FERRIS and GRAVELY mowers.


255-15778

Ferris# 5022584Ferris# 5023231Ferris# 5023432Simplicity# 5023432Simplicity# 5023432SMSnapper# 5023432Snapper# 5023432SM

(Replaces Ogura: GT2.5-FE01S)

Size: 1-1/8” ID X 2-7/8” HT, Pulley diameter: 6-7/16″ OD. Uses 1/2” or 5/8” belt. Rotation: Counter Clockwise.Fits FERRIS, SIMPLICITY and SNAPPER mowers.

255-15780

Simplicity# 7075672YPSnapper# 7075081Snapper# 7075672Snapper# 7075672YPSnapper# 75672

(Replaces Ogura: GT2.5-SN01)

Size: 1” ID X 2-7/8” HT, Pulley diameter: 6″ OD. Uses 1/2” or 5/8” belt. Rotation: Counter Clockwise.Fits SIMPLICITY and SNAPPER mowers.

255-06272

Murray# 690461Murray# 690461MAMurray# 7601023 Scotts# 690461 / 7601023 Warner# 5218-32Warner# 5218-35

Size: 1″ ID X 3-1/8″ HT, Pulley diameter: 6″ OD. Uses a A / B belt. Fits Murray - Scotts models. Has a built in 1/4″ keyway. Note: If the customer has the Short D drive in his old clutch they will need to drive it out and reuse it to keep the new clutch from burning up.

255-740

Cub Cadet# 717-1774C Cub Cadet# 917-1774C MTD# 717-1774C MTD# 917-1774B MTD# 917-1774C Warner# 5219-25

Size: 1″ ID X 4-1/4″ HT, Pulley diameter: 5-15/16″ OD. Uses 5/8″ belt. Rotation: Counter Clockwise. Fits Cub Cadet, MTD and Toro/ Home Depot models. Fits Cub Cadet models: RZT54, GT1554, SLT1554 and LT1024; also fi ts 50″ Toro/Home Depot and 54″; 800 series mowers.



18-09


C C

255-12899

Cub Cadet# 717-04180Cub Cadet# 917-04180MTD# 717-04180MTD# 917-04180Troy Bilt# 717-04180Trpy Bilt# 917-04180 Warner# 5219-52

Size: 1-1/8″ ID, Pulley diameter: 6″ OD.Uses 5/8″ belt. Fits Cub Cadet models: GT2500 series & LT2042, GT2544, GT2550 & GT2554.

255-14229

Cub Cadet# 717-04552 / A Cub Cadet# 917-04552 / A MTD# 717-04552 MTD# 917-04552 Warner# 5219-98

Size: 1” ID X 4” HT, Pulley diameter: 6” OD. Uses 1/2 or 5/8” belt. Rotation: Counter Clockwise.Fits CUB CADET models: FMZ50, LTX1042, LTX1045, LTX1046, LTX1050, 2008 and newer, RZT50, RZT54 and Z-Force S series; Fits TROY BILT models: Mustang XP, 2010 thru 2012.

255-12981

Exmark# 1033245 Warner# 5218-100 Warner# 5218-228 Warner# 5218-243

Size: 1″ ID, Pulley diameter: 7-1/8″ OD. Uses 5/8″ belt.Fits Exmark models with 20 and 23 Hp Kohler engines, Replaces Warner 5218-243 with pigtail, 5218-228 without pigtail & Warner# 5218-100

255-753

Exmark# 1092916 Exmark# 1099276 Warner# 5218-205

Size: 1″ ID, Pulley diameter: 7-1/8″ OD, Uses belt width: 5/8″.Found on Exmark models Lazer Z HP s/n 720,000 and up (Except 27 Hp). (Uses our 255-800 pig tail connector).


255-12977

Exmark# 1030665 Exmark# 1631732 Exmark# 1641300 Exmark# 614300Exmark# 631732Exmark# 641300 Ferris# 1521145Ferris# 5021145 Scag# 461395Scag# 461716Scag# 481530Simplicity# 5021145

Size: 1-1/8″ ID X 2-3/4″ HT, Pulley diameter: 6″ OD. Uses a 5/8″ belt. Fits Exmark Lazer Z models; also found on Ferris, Scag and Simplicity equipment.Replaces Ogura#’s GT2.5-MC04 / MA-GTEXM14Z

255-14841

AYP# 287301Husqvarna# 505 28 73-01Dixon# 287301Dixon# 505287301Kees# 287301Warner# 5219-108

Size: 1” ID 4” HT, Pulley diameter: 5.345″ OD.Uses 1/2” belt. Rotation: Counter Clockwise.Fits Husqvarna Models EZ4824, EZ5221, EZ5226, EZC4824, LSZ4622, LSZ5422, LSZ 5424, RZ4219, RZ4619, RZ4620, RZ4621, RZ4623, RZ5422, and RZ5424.

255-14743

Simplicity# 5100084Simplicity# 5100084SMSnapper# 5100084Snapper# 5100084SMWarner# 5218-221

Size: 1-1/8” ID X 3-3/4” HT, Pulley diameter: 6-1/2″ OD. ,Uses 1/2” or 5/8” belt,Rotation: CC. Fits FERRIS models: DD series walk behind, Evolution 36”, 48” and 52”, FX150XT, 52” and F200XT, 61” series, F50XT, 36”, 19-20 Kawasaki series, Flail mower series, IS1500Z, IS1500ZX and IS2000Z series; Procut S series. Fits SIMPLICITY models: 5900522, 5900523, 5900524, 5900525, 5900526, 5900527, 5900530, 5900531, 5900762, 5900764, 5900820, 5900821, 5900954 and 2690479 Citation series; Fits SNAPPER models: S50X, S75X, S150X, S200X, S50XT, S125XT, S150XT, S200XT, SW30KAV and SW35KAV series.


18-10



C C

255-14327Cub Cadet# 717-04183 Cub Cadet# 917-04183 Cub Cadet# 717-04622Cub Cadet# 917-04622Cub Cadet# GT1AMT09 MTD# 717-04183 MTD# 917-04183MTD# 917-04622 MTD# 917-04622MTD# GT1AMT09Warner# 5219-99

Size: 1” ID X 4” HT, Pulley diameter: 5-3/8” OD.Fits Cub Cadet, MTD. Models: 17AA5AAG700 RZT-42 (2008), RZT-42 17AA5AAG700 (2008), RZT-42 17AA554G755 (2006), 17AA554G755 RZT-42 (2006), 17AA5AAG766 RZT 42 (2006), 17AA5ABP766 RZT 50 (2006), 17AF2ACP011 MUSTANG RZT 50 (2008), 17AF2ACP066 MUSTANG RZT 50 (2008), 17AF2ACP211 MUSTANG RZT 50 (2008), 17AF2ACP711 MUSTANG RZT 50 (2007), 17AF2ACP766 MUSTANG RZT 50 (2007), ZT-42 (2006), 17AA554G790 (2006), ZT-50 (2006), 17AA557P790 (2006), ZT-5000 (2007), 17AD2ACP790 (2007), ZT-42 (2005), 17BA5A4G790, ZT-50 (2005), 17BA5A7P790, 17BF2ACP011 Mustang XP (2009), 17BF2ACP066 Mustang XP (2009), 17BF2ACP211 Mustang XP (2009).

255-121Ayp (sears,roper) 179334 Ayp (sears,roper) 400008 Ayp (sears,roper) 414336 Ayp (sears,roper) 414717 Ayp (sears,roper) 471717P Husqvarna 532179334 Husqvarna 532400008 Husqvarna 532414336 Husqvarna 532414717 Husqvarna 53464900 Husqvarna 917179334 Husqvarna 917414717 Husqvarna 917532179334 Husqvarna 917532414336 Husqvarna 917532414717

Size: 1” ID X 3” HT, Pulley diameter: 6″ OD. Uses 1/2” belt.

Replaces Ogura#’s 53464900 /GT1A-EH07 .

Electric PTO Clutch. Fits HUSQVARNA models: YTH1848, YTH2146, YTH2148, YTH2348, YTH2448, YTKH1848 and POULAN PB26H54Y, PB23H48YT; also 2146 XLS, 2246 LS, 2346 XLS, 2348 LS, EZ 4220, EZ 4624, EZ 4822, EZ 4824, EZ 5224, EZ 5226, WH 3615 / 4817 / 5217 (2008), WHF 3617 / 4817 / 5223 / 6123 (2009), YTH 2146 XP (2007/08) YTH 22 V 42 LS, YTH 22 V 46 XLS, YTH 23 V 42 LS (2009/10) YTH 23 V 48 (2010) YTH 2348 (2008/09/10) YTH 24 V 48 LS (2009) YTH 24 V 54, YTH 2454 (2010) YTH 1848 XP (2003-05) YTH 1848 XPF (2002) YTH 1848 XPT (2006) YTH 2146 XP (2006) YTH 2148 (2003-05) YTH 2148 A (2003) YTH 2148 B, YTH 2148 C, YTH 2248 A, YTH 2248 B (2004), YTH 2348 (2006) YTH 2448 (2004-05) YTH 2448 T (2006) YTH 2548 A, YTH 2548 B, YTH 2748 (2004), YTKH 1848 XPA (2003) YTKH 1848 XPB (2004).ALL ELECTRIC PTO CLUTCHES WILL NOT BE WARRANTIED IF NOT INSTALLED BY A SERVICING DEALER.

255-800

Warner# 15218-251-008 Warner# 5218-251-001 Warner# 5218-251-008

Clutch Pigtail harness. Replaces Warner# 5218-251-001. Does not have a diode like Hustler & Grasshopper use. Fits our 255-737, 255-753, 255-787 as well as many others.

255-507

Scag# 461073Scag# 461074Scag# 481633Scag# 48786Ogura#MA-GT-EXM3XS

Size: 1” ID X 3” HTPulley diameter: 6″ OD. Uses 1/2” or 5/8” belt.Pigtail Included.

Electric PTO Clutch. Fits Scag 36”,48” And 52” Hydraulic Walk-Behinds, Scag 61” & 72” Hydraulic Drive 3 Wheel Riders and Scag 32” thru 72” Belt Drive Walk-Behind.

255-0788Ferris# 1757359 Murray# 1757359YP Simplicity# 1757359YP Snapper# 1757359YP

Size: 1” IDPulley diameter: 5-5/16″ OD. Uses 1/2” or 5/8” belt. Rotation: Counter Clockwise.

Replaces Ogura#’s GT-JD11 / MA-GT-JD11.

Electric PTO Clutch.Fits SIMPLICITY models: ZT2042, ZT21546, ZT2346, ZT2300, ZT2552; 42”, 46” 48”, 50” and 52” decks. Fits SNAPPER models: ZT1842; EZT2042, ZT21546, ZT2346 on 200Z series, ZT2548 on 300Z series etc. Also fi ts several other Simplicity / Snapper models using the Ogura clutch.

255-151John Deere# TCA19812 Warner# 5219-84

Size: 1-1/8” ID X 2-7/8” HTPulley diameter: 6-7/8″ OD. Uses 5/8” belt. Rotation: Counter Clockwise.

Fits JOHN DEERE models: Z510A and Z520A with 54-inch deck, Z2710A up to #20000 Estate Z trak. Replaces TCA16997.


18-11



C C

255-0847

John Deere# AM134397 John Deere# AM141536 Warner# 5219-62 Warner# 5219-87Warner# 5219-127

Size: 1” ID Pulley diameter: 5-1/2″ OD. Uses 1/2” or 5/8” belt. Rotation: Counter Clockwise.

Electric PTO Clutch.Fits JOHN DEERE models: Z425 and Z445 EZTraks, Serial No. 040000 ad lower; X300, X300R, X304, X310 and X320 series.

255-111

Ariens# 00191109 Gravely# 00191109 Scag# 461772 Scag# 482911

Size: 1” ID X 2-7/8” HTPulley diameter: 6-1/8″ OD. Uses a 1/2” or 5/8” belt.

Replaces Ogura#’s GT2.5-RM01.

Fits SNAPPER PRO 47” and 54”. Found on ZTR 355Z, 365Z and Z-Rider series commercial mowers.

255-119

Dixie Chopper#500144 Ferris# 5100417 Gravely#04553800

Size: 1-1/8” ID X 3-1/4” HTPulley diameter: 6″ OD. Uses 1/2” or 5/8” belt.(Made by an O.E.M. supplier).

Replaces Ogura#’s 53462700 / GT1A-EH01.

Fits GRAVELY models: Pro Turn 48”, 52” and 60”; also found on some DIXIE CHOPPER and FERRIS zero turn models


255-16035

Ayp (sears,roper)# 198143Ayp (sears,roper)# 532198143Husqvarna# 198143Husqvarna# 5321981-43

Size: 1” ID X 4” HTPulley diameter: 4.920″ OD. Rotation: Counter Clockwise.

PTO Clutch for AYP / HUSQVARNA built equipment. Fits Husqvarna Models CTH151T, CTH192, CTH2642, CTH2038, CTH182T and LT2223CMA2 (2010 thru 2013).

255-126

Ariens# 00447100 Gravely# 00447100

Size: 1-1/8” ID X 3-9/32” HTPulley diameter: 6-7/16″ OD. Uses 1/2” or 5/8” belt.

Replaces Ogura#’s GT3.5-VP01R

Electric PTO Clutch or ARIENS / GRAVELY models: PM148, PM152, PM252, PM260, PM272 etc. Fits GRAVELY models: Pro Turn 48”, 52” and 60”; also found on some DIXIE CHOPPER and FERRIS zero turn models

255-127

Scag# 461395Scag# 461716Scag# 481530

Size: 1-1/8” IDPulley diameter: 6-1/8″ OD. Uses 1/2” or 5/8” belt. (Made by an O.E.M. supplier).

Replaces Ogura#’s GT3.5-MC07 / MA-GT3.5-MC07

Fits SCAG equipment. Also see our 255-12977


18-12



C C

255-15204

John Deere# TCA16665 Warner# 5219-71

Size: 1-1/4” IDPulley diameter: 6-1/4″ OD. Uses 1/2” or 5/8” belts. Rotation: Counter Clockwise. (Made by an O.E.M. supplier).

Fits JOHN DEERE models: 647, 657, 667 QuickTrac if MIA10991 Short Block has been installed; 647A & 667A [ALL].

255-15209

John Deere# TCA20380 Warner# 5228-3

Size: 1-1/8” ID X 3-1/4” HT Pulley diameter: 6-7/8″ OD. Uses 5/8” belts. Rotation: Counter Clockwise.

Fits JOHN DEERE models: Z820A 60” & all Z830A, 840A, 850A & 860A; Z920A 60” & all Z930A, 950A, 960A, 970A & 925A up to serial #20000.

255-15276

Exmark# 1099282Exmark# 116-1604 Exmark# 116-1620 Toro / Wheel Horse# 1099282 Toro / Wheel Horse# 1161604 Toro / Wheel Horse# 1161620 Warner# 5218-207

Size: 1-1/8” ID X 3-1/4” HT Pulley diameter: 7-3/16″ OD. Uses 1/2” or 5/8” belt. Rotation: Counter Clockwise.

Fits EXMARK models: Lazer Z S, E and X series, Serial No. 312,000 and higher; Next Lazer Z, air-cooled, Serial No. 790,000 and higher and Next Lazer Z ASX, Serial No. 850,000 and higher; Quest SP, Serial No. 850,000 and higher; Fits TORO models: Z Master G3 turbo force, Serial No. 290000001-312999999, 48”, 52”, 60” and 72” decks.


255-15316

Cub Cadet# 717-04376 Cub Cadet# 717-04376A Cub Cadet# 917-04376A Mtd# 717-04376 / AMtd# 917-04376 / A Warner# 5217-44

Size: 1” ID, Pulley diameter: 6″ OD. Uses 1/2” or 5/8” belt. Rotation: Counter Clockwise.

Fits MTD models: 17-Z Series, RTZ Series.

255-15783

Ariens# 03789900 Ferris# 1717664 Ferris# 1720532 Ferris# 540220 Gravely# 03789900

Measures: 1” ID X 3-3/16” HT,Pulley diameter: 5-11/32″ OD Uses 1/2” or 5/8” beltRotation: Counter Clockwise.

(Replaces Ogura: GT1A-CH03L / GT1A AR).

Fits ARIENS / GRAVELY and FERRIS applications.

255-15777

Cub Cadet# 01008544P Cub Cadet# 61008544 Cub Cadet# 717-04127 Cub Cadet# 917-04127 MTD# 01008544MTD# 61008544 PMTD# 917-04127

Measures 1” ID, Pulley diameter: 5-5/16″ OD Uses 1/2” or 5/8” beltRotation: Counter Clockwise.

(Replaces Ogura: GT1-JD08).

Fits CUB CADET models: RZT17, RZT22, RZT42 and RZT50; Z-Force models.


18-13



C C

255-15779

John Deere AM131779

Size: 1-1/8” ID X 3” HT Pulley diameter: 5-5/16” ODUses 1/2” . Rotation: Counter Clockwise.

(Replaces Ogura: MA-GT-JD23BF).

Fits JOHN DEERE models: 325, 335, 345, GX335-GX345 and GX355, diesel, Serial No. 120000 and lower.

255-15781

Murray# 1686880 / SM Simplicity# 1686880 / SM Simplicity# 1687746YPSimplicity# 1687796Simplicity# 1720532 / SMSnapper# 1686880 / SM Snapper# 1717664 / SMSnapper# 1687746YP Snapper# 1717664SM / 1720532 Snapper# 1686880 / 1686880SM

Size: 1” ID X 3-3/16” HTPulley diameter: 5-5/16” OD Uses 1/2” or 5/8” belt. Rotation: Counter Clockwise.

(Replaces Ogura: GT1-BS03)

Fits MURRAY, SERAS/CRAFTSMAN, SIMPLICITY/ALLIS CHALMERS and SNAPPER/KEES mowers.

255-15210

John Deere# GY20108John Deere# GY20652John Deere# GY20878John Deere# GY21340Warner# 521920Warner# 521972

Size: 1” ID X 3-1/4” HT Pulley diameter 6-5/16 ” ODUses 5/8” belts. Rotation: Counter Clockwise. (Made by an O.E.M. supplier).

(Replaces WARNER# 5219-20 / 5219-72.)

Fits some JOHN DEERE models: 145, 155C, 190C, L120, L130, LA130 and LA140 & Scotts L2048 and L2548.


255-264

John Deere# AM123123 Warner# 5215-34

Size: 1-1/8” ID X 3-5/8” HT Pulley diameter 5-1/2” ODUses 1/2” beltRotation: Counter Clockwise.

Fits JOHN DEERE models: LX180, LX186 lawn tractors; GS25, GS30, GS45, GS75, HD45 and 75 commercial walkbehinds..

255-263John Deere# AM100977 John Deere# AM115090 John Deere# AM118969 John Deere# AM119971 John Deere# AM122969 John Deere# AM123038 John Deere# AM38260 Warner# 5215-35 / 5215-92 Warner# 5215-96 / 5215-112

Size: 1” ID X 3-1/2” HT Pulley diameter 5-5/16” ODUses 1/2” Belt Rotation: Counter Clockwise.

Fits JOHN DEERE models: LX172, LX173, LX176, LX178, LX186 and LX188 lawn tractors.

255-266John Deere AM105302 Warner 5215-43Warner 5215-171

Size: 1-1/8” ID X 4-1/4” HT Pulley diameter: 4-1/8 (double)” ODUses 1/2” or 5/8”beltRotation: Counter Clockwise.

Fits JOHN DEERE models: Most F710 w/54 deck & F725 w/48 deck Front Deck Mowers.

255-272John Deere# AM138729 Warner# 5219-116

Size: 1” ID X ____ HT Pulley diameter 6.550” ODUses 1/2” or 5/8” beltRotation: Counter Clockwise.

Fits JOHN DEERE model: Z245 EZTrak.


18-14



C C

255-267

John Deere# AM103035 John Deere# AM108601 John Deere# AM115093 John Deere# AM119536 Warner# 5215-44

Size: 1-1/8” ID X 4-1/4” HT Pulley diameter 5-5/16” ODUses 1/2” or 5/8” beltRotation: Counter Clockwise.

Fits JOHN DEERE models: 240, 245, 260, 265, 285, 320, GT242, GT262, GT275, 345 before serial number 070,000, 325 before serial number 070,000 and SABRE models: 2254HV and 2554 and SCOTTS model: S2554.

255-269Honda# 80186VK1003 John Deere# AM121972 Warner# 5217-8Warner# 5217-20 Warner# 5217-36Warner# 5217-38

Size: 1” ID X 3-1/2” HT Pulley diameter 5-1/4” ODUses 1/2” or 5/8” beltRotation: Counter Clockwise.

Fits JOHN DEERE models: STX38 and STX46.

255-270


Size: 1” ID X 3” HT Pulley diameter 5-5/16” ODUses 1/2” beltRotation: Counter Clockwise.

Fits JOHN DEERE models: GT225, GT235, GT245, GX255, LT190, LX255, LX266, LX277, LX279, LX280, LX288, LX289, SST16 and SST18.

255-271



Fits JOHN DEERE model: Z225 EZTrak.


255-273

John Deere# TCA14535 Warner# 5219-32 Warner# 5219-223

Size: 1-1/8” ID X 3” HT Pulley diameter 6-5/16” ODUses 5/8” beltRotation: Counter Clockwise.

Fits JOHN DEERE models: 717 & 727 if MIA10991 S/B installed; 717A & 727A up to serial #30000; 717E.

255-274

Great Dane# D38155 Great Dane# GDA10017 John Deere# GDA10017 Lesco# GDA10017 Warner# 5219-4

Size: 1” ID X 3-1/4” HT Pulley diameter 6” ODUses 1/2” or 5/8” beltRotation: Counter Clockwise.

Fits JOHN DEERE models: 717 Mini-Frame ZTrak, 727 Mini-Frame ZTrak, 647 Quik-Trak, 657 Quik-Trak and 667 Quik-Trak.

255-275

John Deere# AM136787 John Deere# AM137323 John Deere# AM138730 Warner# 5219-88


Fits JOHN DEERE models: Z225 EZTrak Residential, Z425 EZ Trak Residential, Z445 EZ Trak Residential and EZTrak Residential. Fits JOHN DEERE models: Z225 up to #100000, Z425 & Z445 #40001 and up, and Z465 [ALL].


18-15



C C

255-276

John Deere# TCA16998 John Deere# TCA19813 Warner# 5218-245

Size: 1-1/8” ID X 2-7/8” HT Pulley diameter 6-7/8” ODUses 1/2” or 5/8” beltRotation: Counter Clockwise.

Fits JOHN DEERE models: Z520A Estate ZTrak, Z720A ZTrak, Z810A Pro ZTrak, Z820A Pro ZTrak, Z910A Pro ZTRak and Z920A Pro ZTrak. Fits JOHN DEERE models: Z520A w/60” Deck Estate ZTrak, Z810A & Z820A 48”, Z720A, Z910A, Z920A 48”/54” up to serial #20000 Professional ZTrak.

255-277

John Deere# TCA20604 John Deere# TCA21167 Warner# 5218-271

Size: 1-1/8” ID X 3-3/4” HT Pulley diameter 6-5/8” ODUses 5/8” beltRotation: Counter Clockwise.

Fits JOHN DEERE models: Z910 ZTrak, Z920A ZTrak, Z910A Pro ZTrak, Z920A Pro ZTrak and Z925A Pro ZTrak. Fits JOHN DEERE models: some Z710A, most Z720A; Z925A EFI 54”; Z910A, Z920A 48” / 54” & Z925A 54” serial #20001 and up.

255-823

Exmark# 1106766 Toro / Wheel Horse#1106766 Warner# 5219-81

Size: 1” ID Pulley diameter 6-5/16” ODUses 1/2” or 5/8” belt

Fits EXMARK models: Quest, Serial No. 790,000 and higher, 48” and 52” deck; Fits TORO models: SS5000, SS5060, ZS5000, Z5020, Z5030, Z5035, Z5040, Z5060, Timecutter, Titan Z4800, Z5200, ZX5000 and ZX5020.


255-14778 Cub Cadet# 717-1787 / 917-1787MTD# 717-1787 / 917-1787

For MTD built equipment. Bottom Pulley: 6.7” OD / 40 Degree (NORCB129)

255-14779 Cub Cadet# 717-1788ACub Cadet$ 917-1788A MTD# 717-1788A MTD# 917-1788A

For MTD built equipment. Bottom Pulley: 6.7” OD / 34 Degree (NORCB128)

255-14782 AYP# 170163 AYP# 179887 AYP# 198144 Husqvarna# 532 17 98-87

For AYP built equipment. For all AYP built lawn tractors withSoft Touch PTO (Noram). Bottom Pulley: 5.6” OD

255-14783 AYP#180354 Husqvarna# 532 18 03-54

For AYP built equipment. Bottom Pulley: 4” OD

255-14784 AYP# 198144 Husqvarna# 532 19 81-44

For AYP built equipment. Bottom Pulley: __” OD

255-14785 AYP# 408579

For AYP built equipment. Bottom Pulley: 5” OD

ELECTRIC PTO CLUTCHES MANUAL - PTO CLUTCHES cont.

18-16


C C

646-126 Echo# 175009-05532 Green Machine#190025 / 190111 Hoff co# 211325S John Deere#AM115397 Red Max#1100-51113 1130-00602

ClutchFits Echo Trimmer models SRM250, SRM2000, SRM2200, SRM2500, SRM2501, SRM2502, SRM2510, SRM2510S. Green Machine models 1900, 2400M, 2500, 2800, 2810, 3000M, 3000SS, 3010M, 4000M. Hoff co models 95 - JP30F300, 96 - JP220F and 95/96 - SE301F. Red Max models Bt2000, BC2001DL and BC2300DL.

Size: 2″ OD with (2) 5/16″ ID mounting holes.

646-183 Ryan# 181598 Ryobi# 181598 Stihl#4130-160-2000

ClutchFits Ryan / Ryobi Trimmermodels with clutch. Fits Stihl Trimmer model FS36,also fi ts Kaaz Trimmer model T-170 and Ryobi 31cc .

Size: 2-27/64” OD X 3/8” - 24 RH thread.NOTE: For use with our 646-184 Clutch Drum - see our “TRIMMER PARTS” section for more information.

646-142 Homelite /Jacobsen# 9806329130182078Kawasaki#13018-2078 13081-2194

ClutchFits Homelite (with Kawasaki engine) Trimmer / Brushcutter model: HK-33,also fi ts Kawasaki models: TD-40, TD-43 and TD-48.

Includes: (2) shoes, (1) spring, (2) bolts and (2) washers. Size: 3” OD with (2) .390” ID mounting holes, overall height: 9/16”. (FYI: “OD: = Outside diameter and “ID” = Inside diameter.)

646-127 Shindaiwa# 20035-51100 20035-51101 / 70140-5110070140-51102 / A056000260

ClutchFits ShindaiwaTrimmer / Brushcuttermodels: F18, T18, T20,LT20, C20 and T/C230.Size: 2-1/16″ OD,Includes (2) bolts, (2) washers and (2) springs.

646-128 Shindaiwa# 20000-51103 Shindaiwa# 20000-51104Shindaiwa# 20018-51100 Shindaiwa# 70140-51102

ClutchFits Shindaiwa Trimmer /Brushcutter models:TC25 and TC250.

Size: 2-1/16″ OD, includes (2) bolts, (2) washersand (2) springs.

646-099 Shindaiwa# 20024-51101Shindaiwa# 70102-51100

ClutchFits Shindaiwa rimmer /Brushcuttermodels:C35 and B45.

Note: For use with our 646-250 Clutch Drum- see our ″TRIMMER PARTS″ section for more information.

646-129 Weedeater# 530-069195 Weedeater# 530-093919Poulan# 93919

Clutch For many smallPoulan chain saw and Poulan / WeedeaterTrimmer models.

Size: 2-3/8” OD, steel washer included.

www.bantasaw.com

TRIMMER CLUTCHES TRIMMER CLUTCHES

18-17

small engine parts & accessories chainsaw chainsaw … · small engine parts & accessories...

Documents