slimcap tech spec v1 0
TRANSCRIPT
SlimcapSlimcapSlimcapSlimcap Technical Specification v1.0
CONCRETE WEIGHBRIDGES
RADICALLY REMOVED IN OUR SLIMCAP
WEIGHBRIDGE WITH MODULAR COMPONENTS IN
PRECOMPRESSED REINFORCED CONCRETE
Pag. 2/7
Description and General Specification
Execution fully electronic, low-
profile modular construction.
Slimcap can be installed in a
low pit or at ground level -
overall dimensions 48 cm
approx.
Platform consisting of
prefabricated modular
elements in pre-stressed
reinforced concrete (Rck 50
N/mmq).
Laser-cut steel connecting
heads (Fe B44k), complete
with
inspection holes.
designed for long life and
consistent
performance and to bring
down costs for owner
operators.
Steel bases with oscillation
limiting devices.
Stainless steel or galvanised
nuts and bolts.
Load cells of omologated
compression and certified
OIML R60. Made of stainless
steel, sealed construction,
IP68 degree of protection C4.
Triple safety against lightning
and overvoltage consisting of
upstream and downstream
insulation barriers, copper
plait “By Pass” and earthing
connections - limiting devices
to regulate the platform’s
oscillation width, complete
with safety struts.
The weighbridge Slimcap is
modular and can then be
further amended in its length
and scope at a reasonable
price.
The project provides a
concrete mixer with automatic
dosing and less than 4
different types of aggregates
with particle size to ensure the
highest quality of product.
Undergo a preanufactured
goods are all aging and
subsequently transferred to
our facility for the final outdoor
aging for at least 30/40 days.
They’re then individually tested
form and finished for
maximum certainty of the
perfect fit on site.
Dimension
See chart overleaf
Approvals
All data relating to the
performance of the machine
meets and exceeds
requirements of EN45501
European Approval Accuracy
Class III machines.
Load cells:
OIML R60
C4
Environment
Load cell:
Operating temperature: -10°C to +65°C
Storage temperature: -20°C to +70°C
Resistance to Dirt & Moisture IP68
Pag. 3/7
Options
1.
WF wireless transmission to
indicator. Our constant research for the solution
of our customer problems has brought
us to achieve WF, the innovative
wireless weight system which allow you
to connect any weighing platform and
weigh bridges any kind and dimension,
to the weighing indicator or to a PC,
without the wiring cables.
Confort, versatility, easy to install and
moving are the maximum with WF.
The transmission system consisting of
two transceiver RF which can realize a
wireless bi-directional communication.
The maximum RX/TX range, if the
antennas are in LOS, can reach a
maximum of 40 meters. With a directional antenna you can
reach until 350 meters. It’ a Trade Approved system.
2.
Sun System. Sun System is able to power any
weighing systems; it make
independent them from the 220Vac
mains.
Sun System consist of a photovoltaic
panel, two Pb batteries and a regulator
board.
The latter has these functions: check
the battery charge and avoid that their
voltage drops below 11 volts.
3.
ATEX Certification. For each load cell.
4.
PIT frame. Dimensions:
7.7x3 m
9 x 3 m
15 x 3 m
18 x 3 m
22 x 3 m
Picture 1 SunSystem + WF
Pag. 6/7
Picture3 Panels transport Picture4 Panel lifting
Picture5 Swinging control Picture6 Load cell housing Picture7 Head/Pannel support
Pag. 7/7
Your local distributor:
This brochure contains a generalguide only of the product and shall not form part of any contract unless specifically agreed by Cogo Bilance Srl in writing each case of the Order Acknologement.
The specification of the products decribed herein may vary from time to time may be altered without notice.
Stabilimento di Camponogara Via dell’Industria, 51 30010 Camponogara (VE) Tel. 041.5380888 Fax 041.922862 [email protected]
Stabilimento di Oggiona Via Risorgimento n. 3 21040 Oggiona con S. Stefano (VA) Tel. 0331.212312 Fax 0331.219778 [email protected]
Filiale di Alessandria Via Torino, 14 15100 Alessandria (AL) Tel. 393.9951107