sleeping...• beds in 2 different surface heights • comprehensive bed accessories: different...

www.huelsta.com

9/19Type list

SLEEPING

E

2Schlafen: LUNISE 9. 2019

Important notes: Generally speaking, you as a dealer/qualified fitter are responsible for the correct wall mounting of the units. That is why wall mounting should only be carried out by properly trained and qualified fitters. hülsta supplies materials for mounting units on walls for nearly all the units and which should be used for safety and for constructional reasons. The assembly materials supplied by hülsta (plugs, screws) are only suitable for fitting components on to concrete in firmness class C12/15.For other materials (please see separate materials table in the wall composition chapter) we provide you with an assembly mortar set as an extra order. Please note that this assembly mortar set is also only suitable for the materials listed in the materials table. If walls are made up of other materials (e.g. plastered or lighter wall materials), one should use another method of mounting better suited to the load on site. Please note that if the units are not mounted properly on the wall, there is a risk of the units falling down or tipping over – especially when alternative mounting materials acquired on site have been used.For the reasons stated above it is absolutely essential to enquire about the composition of any walls before signing any contracts.

Range introduction

LUNIS

Ancillary units• Consoles with flush fronts; in one height and two widths, console for pedestals• Pedestals in one height and two widths• Chests with drawers or doors, with flush fronts, high chests with drawers or with flap and drawers, wall

chests with drawers; in four widths• Dressing chest• Angled shelves, with optional lamps• Drawer frames of consoles and chests in standard grey version

WardrobesHinge-door wardrobes according to the endless assembly principle• Hinge-doors with shell handle, optionally in a different version to the hinge-doors• Hinge-doors with flush front, optionally with flush-front mirrors (at a surcharge)• With optional cornice profile and/or top LED lamp (12 V; 2.4 W)• Wardrobe interior carcase in standard white lacquer• Standard interior fittings: 2 fitted shelves. 1 clothes rod• Functional and high-quality interior wardrobe fittings (see “Wardrobe interior fittings” type list)

Quality features• Wardrobe doors with shell handles and spring hinges• All metal hinges• Visually unobtrusive 2.5 mm drilled holes for wardrobes• Centre partitions and end side-sections of wardrobes with special plinth adjustment• hülsta Push-to-open: Drawers and doors of ancillary units with hülsta Push-to-open• hülsta MagicClose: All wooden hinge-doors with door hinge cushioning device

Height reductions at intervals of 1.0 cm without surcharge

In combination with the hülsta Sleeping System, the beds guarantee highest sleeping comfort. With its high-grade quality spring base frames and mattresses, the hülsta Sleeping System provides the perfect prerequisites for relaxing sleep (see “Sleeping systems“ type list).

Contents Page

Range introduction, lists of versions 2-3

Special combinations 4-5

Hinge-door wardrobes 6-7

Bed system 9-11

Bed accessories 12-16

Ancillary units, dressing chest, angled shelves, Magic-Tronic, remote control 17-19

General information:

Switch options for lamps 21

Special-sized products, special articles 22-24

Usable bed inside height and space under bed 25

Important notes: quality of walls / assembly instruction 26

... for relaxing, dreaming and wonderful sleep

LUNIS is the bedroom range of your choice if you appreciate having a lot of choice when planning your new bedroom suite. The multitude of creative possibilities that LUNIS has to offer is just as unique as this place of refuge is itself. Classical combinations of slatted base frames and mattresses or Boxspring units, upholstered beds or bed surrounds in wood veneer - all the different bed versions, wardrobes and ancillary units mean that the visual design concept of LUNIS creates a convincing overall impression.

Beds• Beds with upholstered headboard, bed surround in wood/lacquer, high-gloss or upholstered version or with

Boxspring in upholstered version; in four widths and three lengths• Beds in 2 different surface heights• Comprehensive bed accessories: different bedside lamps, headboard panels and numerous accessories for

headboard panels

34

Labelling in type list drawings / assembly notes for wall unitsThe majority of units have two wall mounting points (= number of base plates), if these are to be fitted as wall units. This is not expli-citly mentioned in the type list. If a different number of wall mounting points (= base plates) is required, this is marked in the drawings in the type list with numbers in black boxes. Please be sure to note here the information and notes in the “Wall composition” chapter!

Link to the assembly / user instruction movies

LUNIS

3Schlafen: LUNIS E 9. 2019

Lists of versions

Changing versions:The model nos. for the wardrobe exterior carcase, wardrobe front, shell handle and cornice profile must be stated separately as colour combinations are possible. If versions from different price groups are exchanged, the higher price group is always charged (exception: exchanging versions of shell handle). Wardrobe interior carcase in standard white lacquer version.

WardrobesWardrobe front

White lacquerHigh-gloss whiteNatural oakDark stained oakCore walnut

640860685692680

Wardrobe exterior carcase, cornice profile, shell handle

White lacquerNatural oakDark stained oakCore walnut

640685692680

IIIIIIIII

Model no.Model no.

IIIIIII

640860685692680

Beds

Changing versions:The model nos. for the bed surround and leg A or the cover no. for the upholstered headboard, the upholstered bed surround or the Boxspring must be stated separately as colour combinations are possible. If versions from different price groups are exchanged, the higher price group is always charged.


Bed surround, headboard panel, leg A (round)

IIIIIIIII

Model no.

hülsta cover collectionor

Upholstered headboard, bed surround, Boxspring

Price group

Price group Price group

Changing versions:The model no. for the ancillary unit exterior carcase and front, the open compartment and frame of the open compartment of console, the pedestal carcase and front as well as the dressing chest carcase and front must be stated separately, as colour combinations are possible. When exchanging versions from different price groups, the higher price group is always charged. Ancillary unit interior carcase in standard white lacquer version.

Ancillary units, pedestals, dressing chest, angled shelvesCarcases, open compart-ment of console, angled shelves

White lacquerNatural oakDark stained oakCore walnut

640685692680

Fronts, frame of open compartment of console

640860685692680

Panel carcase with box drawer or flap, angled panel shelves, housing of bedside lamp

Panel carcase with box drawer or flap, angled panel shelves, housing of bedside lamp

White lacquerSaffron lacquerPetrol lacquerPastel green lacquerNatural oakDark stained oakCore walnut

640655654653685692680

IIIIIIIIII

Model no. Price group

Beds with upholstered headboard, bed surround in wood/lacquer, high-gloss or upholstered version or with Boxspring in upholstered version.hülsta cover collection: see „hülsta cover collection“ type list.


Model no.

IIIIIII

Model no. Price group Price group

IIIIIIIII


301

--

0383

-

303

--

0385

-

304

--

0385

-

5-door hinge-door wardrobe(centre door with right hinges) 252 cm wide

Important: Choose a bed with upholstered headboard and surround in wood/lacquer or high-gloss version (all bed sizes possible – please state type no.; see pages 10-11), two consoles (console types 5205 and 5207 are possible – please state type no.; see page 17) as well as one of the wardrobes listed below.

6-door hinge-door wardrobe302 cm wide

4-door hinge-door wardrobe202 cm wide

Surcharge for top LED lamp

1 lamp per unit

Surcharge for cornice profile


1 lamp per unit



1 lamp per unit


Special combinations

Special combinations consisting of bed unit (bed and 2 drawer consoles) and one wardrobe. The price of an entire special combination (bed unit and wardrobe) can be found in the boxes shaded grey!

Bed: Bed with upholstered headboard and bed surround in wood/lacquer or high-gloss version Consoles: Consoles with 2 drawers, optionally 51.2 or 70.0 cm wideWardrobe: Wardrobe with hinge-doors; height reductions of hinge-door wardrobes at intervals of 1 cm without surcharge.

Please also note the mattresses and base frames in the “Sleeping systems” type list!

Price gr.III

Bed with upholstered headboard and bed surround frame in wood/lacquer or high-gloss version and two drawer consoles

Important note:Bed also available optionally with bed surround in upholstered version, with Boxspring, in surface height 2, with other legs or with consoles with open compartment (at a surcharge).See here the following page!

A8406

--

A8416

--

A8436

--

Special-sized products for special combinations are possible! Pricing: special combination + 15%

plus all the required special-sized products (see „Special-sized products“)!

Please note: Height reductions of wardrobes remain free of charge!

LUNIS


This luminaire contains built-in LED lamps of the energy classes A++ to A. The lamps cannot be changed in the luminaire. 12 V; 2.4 W

14 / 22,1 * cm

3002

-

2004

-

2004

-

2004

-

Surcharge for mirrorEach wardrobe door can be fitted with an optional flush-front mirror which is charged extra.

-

Surcharge for mirror per hinge-door

Additional fittings for beds

Additional fittings for special combinations / surcharges / lampsAdditional fittings for wardrobes

Bed headboardStandard version: upholstered headboard with cover in price gr. I

Surcharge for upholstered head-board with cover in price gr. III

Surcharge for upholstered head-board with cover in price gr. II

Surface heightsStandard version: surface height 1 (as in illustration 1)

Bed surroundStandard version: wood/lacquer or high-gloss version

Surcharges for bed surround in uphols-

tered version

Surcharge for bed sur-round in upholstered version with cover in

price group I


price group II


price group III

Illustr. 2Illustr. 1

Alternative bed legs

Surcharge for surface height 2(as in illustration 2)

Surcharges for Boxspring in uphols-

tered version

Surcharge for Box-spring in upholstered version with cover in

price group I


price group II


price group III

3010

-

3020

-

Surcharge for leg A(as in illustration 1)

Surcharge for leg B(as in illustration 2)

2002

-

2002

-

Additional fittings for consoles

Rear surface treated headboardThe upholstered headboard can be given an optional rear side surface treatment (against a surcharge). So the bed can be placed anywhere in the room.

2001

-

Surcharge for 70.0 cm wide console with open compartment (as in illustration 2);

surcharge per console:


2003 2003 2003- - -

ConsolesStandard version: with 2 drawers, 51.2 or 70.0 cm wide (as in illustration 1)

Maximum usable bed inside height (when support slats in bottom position)

* Surface height: see here the information on page 12!

=

=

Top LED lamp

1602 -

1603 -

Remote control

Surcharge for extra transmitter type

Surcharge for extra receiver type

Surcharge for remote control unit(transmitter + receiver) type

-1601

=

=

Surcharge for each additional lamp type 369 -15

,9 /

15,0

cm

16,5

/ 17

,2 c

m

16,5

/ 17

,2 c

m

24,0

/ 22

,0 c

m



369 -

This luminaire contains built-in LED lamps of the energy classes A++ to A. The lamps cannot be changed in the luminaire. 12 V; 2.4 W

=

=

Top LED lamp

1602 -

1603 -

Remote control

Surcharge for extra transmitter type

Surcharge for extra receiver type

Surcharge for remote control unit(transmitter + receiver) type

-1601

=

=

61.4 cm

see page 7Widths

Depths

229.6 cm

Dimensions

Height reductions at intervals of 1.0 cm without surcharge

Heights incl. plinth

74.2 cm

234.6 cm

with LED top lamp

without cor-nice profile

with cornice profile

with cornice profile and top

LED lamp

231.0 cm 235.4 cm

61.5 cm 68.7 cm

61,4

242

61,4

202

61,4

302

Hinge-door wardrobesNotes on planning hinge-door wardrobes according to the endless assembly principle

Hinge-door wardrobes can be planned endlessly and combined with one another. Due to the various element widths one can create many total wardrobe widths. In this way the available floor space can be exploited to the full. For each wardrobe combination, the first element on the left is conside-red to be the basic unit, incorporating both outer side-sections. One can only include one basic unit in each combination. When adding on extension units, the right-hand side-section of the basic unit is employed as the end side-section of the complete combination. In the case of single-door hinge-door units one can choose between left- and right-hand hinges. The graphics shown below give you an excerpt from our wardrobe assortment.

Standard interior fittings per unit: 2 fitted shelves, 1 clothes rod. All interior surfaces are in white lacquer.

Examples of wardrobesHinge-door wardrobe Hinge-door wardrobe

Hinge-door wardrobe

• Hinge-door wardrobes can be planned endlessly and combined with one another• Cornice profile, flush-front mirror fronts and lamps at a surcharge• Unit outside widths: 42, 52, 82, 102 cm (basic units) 40, 50, 80, 100 cm (extension units)• Unit inside widths: 38, 48, 78, 98 cm• Outside depth: 61.4 cm• Inside depth: 56 cm• Door opening angle: approx. 94°



LampsAll hinge-door wardrobes are available with top LED lamps. One top LED lamp is fitted standard above each element – 1 or 2 door – 12 V; 2.4 W. If required, a top LED lamp can be fitted centrally above each door. Please include a sketch in all cases.Switching is done by an external foot switch. A radio remote control is also available as an alternative, which is charged extra. The radio remote control incorporates one transmitter and one receiver which operate all the LED lamps. The foot switch is omitted when the radio remote control is employed.

Please note: When including the cornice profile, please note that the distance to the ceiling must be at least 2.0 cm.

Surcharge for each additional lamp type

LUNIS

7Schlafen: LUNIS E 9. 2019 L/R = Door hinge left/right

Single-door unit, left or right, 42 cm wide


Twin-door unit, 82 cm wide






Extension units with 1 centre partition (2 cm thick)

For each project please remember to leave a 2.0 cm gap to the ceiling and at the side for assembly!

Height: 229.6 cm (height with cornice profile and/or top LED lamp: see table on page 6 top right; height reductions in intervals of 1.0 cm without surcharge)Width: see tableDepth: 61.4 cm (depth with cornice profile and/or top LED lamp: see table on page 6 top right)

Interior fittings per unit: 2 fitted shelves, 1 clothes rod;interior fittings always in white lacquer.

All hinge-doors with shell handle, optionally in a different version to the hinge-doors (without surcharge).

Basic units with 2 outer side-sections (each 2 cm thick)

For each wardrobe combination, the first element on the left is considered to be the basic unit, incorporating both outer side-sections. One can only include one basic unit in each combination. When adding on extension units, the right-hand side-section is employed as the end side-section.

Please also note the functional and high-quality wardrobe interior fittings in the „Wardrobe interior fittings“ type list as well as the special articles and possible special-sized products.


1 lamp per unit

Price gr.III

Price gr.III

Price gr.III

Price gr.III

Price gr.III

Price gr.III

Price gr.III

Price gr.III

Notes on energy efficiency class: see page 6!

Doors with flush front


61,4

61,4

61,4

61,4

61,4

L

61,4

L

61,4

L

61,4

L380

-

380

-

380

-

380

-

Please mark exactly in the front sketch or state in the order (from the left) which hinge-doors are to be fitted with a mirror.

Surcharge for mirror per hinge-door:

-

382

-

382

-

382

-

382

-

A02012 RA02011 L

--

3410

--

3420

--

A0202

--

3430

--

A202

--

3440

--

A00012 RA00011 L

--

3460

--

A0012 RA0011 L

--

3470

--

A0002

--

3480

--

A002

--

3490

--

A2012 RA2011 L

--

Hinge-door wardrobesSurcharge for mirrorEach wardrobe door can be fitted with an optional flush-front mirror which is char-ged extra.


Possible arrangements

LUNIS


Example of planning and ordering

3

2

4

1

4

1 Bed with profiled headboard and Boxspring in upholstered version, in surface height 1, 180 x 200 cm2 Console with 2 drawers and 1 open compartment left, 70 cm wide3 Console with 2 drawers and 1 open compartment right, 70 cm wide4 Surcharge for upholstered headboard with function

Example of planning and orderingType 6274Type 52071Type 52072Type 801


---

99971

172 x 224/220192 x 224/220212 x 224/220232 x 224/220

172 x 234/230192 x 234/230212 x 234/230232 x 234/230

172 x 244/240192 x 244/240212 x 244/240232 x 244/240

* Surface height: see here the information on page 12!

Genuine leather

172 x 224/220192 x 224/220212 x 224/220232 x 224/220

172 x 234/230192 x 234/230212 x 234/230232 x 234/230

172 x 244/240192 x 244/240212 x 244/240232 x 244/240

172 x 224/220192 x 224/220212 x 224/220232 x 224/220

172 x 234/230192 x 234/230212 x 234/230232 x 234/230

172 x 244/240192 x 244/240212 x 244/240232 x 244/240

107,

8

betw

een

15.0

an

d 24

.0 *

16,5

/ 17

,2 *

Anti-slip mat2.5 mm high, 170 cm long, 67 cm wideBecause of the low usable inside bed height in standard surface height 1, we recommend including an extra anti-slip mat to avoid the mattress slipping on base frames and mattresses which are quite high ( > 10 cm).

Anti-slip mattype

Upholstered headboard (fixed)Upholstered headboard available optionally with function(at a surcharge, see page 13).

-900

Bed system consisting of upholstered headboard (fixed) with bed surround in wood/lacquer, high-gloss or upholstered version on standard arched support in hovering look or with Boxspring in upholstered version

Beds with bed surround in wood/lacquer, high-gloss or upholstered versionBeds incl. support slats for base frames and mattresses• Adjustable in height by 3.2 cm upwards or 3.2 cm downwards and upwards (see here page 12)• Usable bed inside height: max. 14.0 / 22.1 cmorBeds with Boxspring (fixed, not adjustable)

hülsta cover collection: see „hülsta cover collection“ type list.Please state all the versions clearly in the order!

* Note on outer sizes:Outer length of beds with bed surround in wood/lacquer, high-gloss and upholstered version = inside length +24 cm (example: inside size 200 cm = > outer size 224 cm)

Outer length of beds with Boxspring = inside length +20 cm (example: inside size 200 cm = > outer size 220 cm)

Bed system with upholstered headboard

Note:All bed systems are available optionally in 2 different surface heights and/or with alternative legs at a surcharge, see page 12. Please state clearly in the order!

140 x 200160 x 200180 x 200200 x 200

Upholstered headboard in cover price group I

Upholstered headboard in cover price group II

Upholstered headboard in cover price group III

140 x 200160 x 200180 x 200200 x 200

140 x 210160 x 210180 x 210200 x 210

140 x 220160 x 220180 x 220200 x 220

140 x 220160 x 220180 x 220200 x 220

140 x 210160 x 210180 x 210200 x 210

140 x 200160 x 200180 x 200200 x 200

140 x 220160 x 220180 x 220200 x 220

140 x 210160 x 210180 x 210200 x 210

Please also note the mattresses and base frames in the “Sleeping systems” type list!

Rear surface treated headboardThe upholstered headboard can be given an optional rear side surface treatment (against a surcharge). So the bed can be placed anywhere in the room.

type

Surcharge in price group ISurcharge in price group IISurcharge in price group III

Please be sure to state in the order!

Inside dims. Outside dims.*

LUNIS


----

625626627628

----

635636637638

----

645646647648

----

625626627628

----

635636637638

----

645646647648

----

625626627628

----

635636637638

----

645646647648

14 / 22,1 cm

Genuine leather

Genuine leather

IIII II I II IIII II

Bed surround in wood/lacquer/high-gloss version

Bed accessories: see pages 12-16!

Bed surround in wood/lacquer/high-gloss version

Please be sure to observe the notes on surface heights and alternative legs on page 12!

Bed surround in upholstered version

Please be sure to observe the notes on surface heights and alternative legs on page 12!

Bed surround in upholstered version

Boxspring in upholstered versionfixed, not adjustable

Please be sure to observe the notes on surface heights and alternative legs as well as the product features of

the Boxspring on page 12!

Boxspring in upholstered version

Cover price group Cover price group



Type no.Price group

Type no. Type no.

625626627628

- - - - - - - -

635636637638

- - - - - - - -

645646647648

- - - - - - - -

625626627628

- - - - - - - -

635636637638

- - - - - - - -

645646647648

- - - - - - - -

625626627628

- - - - - - - -

635636637638

- - - - - - - -

645646647648

- - - - - - - -

----

6254626462746284

----

6354636463746384

----

6454646464746484

----

6254626462746284

----

6354636463746384

----

6454646464746484

----

6254626462746284

----

6354636463746384

----

6454646464746484

14 / 22,1 cm


Two different surface heightsAll beds are available in two different surface heights, optionally:

with 15.9/15.0 cm high bed sides = surface height 1 (standard height) orwith 24.0/22.0 cm high bed sides = surface height 2 = Type

If surface height 2 is required (at a surcharge), please state clearly in the order!

with surface height 1:Support slats adjustable by 3.2 cm upwards,usable inside bed height: max. 14.0 cm

with surface height 2:Support slats adjustable by 3.2 cm downwards and upwards,usable inside bed height: max. 22.1 cm

Alternative bed legsThe beds with bed surround in wood/lacquer, high-gloss, or upholstered version stand on a standard arched support in hovering look, the beds with a Boxspring in upholste-red version are on round black standard legs.All beds are available optionally with alternative legs at a surcharge.Please state clearly in the order!

Surcharge for leg A

Standard leg for beds with bed surround in wood/lac-quer, high-gloss or uphols-tered version: on arched support in hovering look

3010

-

3020

-

-3002

Product information BoxspringBox fixed, not adjustable, with upholstered mattress with 7-zone, flat cylinder pocket spring core in a cover of furniture fabric (cover not removable/washable; surface with almost invisible anti-slip feature).

• Height: approx. 16 cm; firmness level: medium; weight approx. 28 kg (100 x 200 cm)• Good zone elasticity• Good body and spine support• Good moisture dispersion• Elastic 7-zone, flat spring core with multiple-sealed cylinder springs, sewn into pockets; 350 springs/m²; core height: ca. 5 cm

Surface height 1 (standard height)

15,9

cm

17,2

cm

24,0

cm

17,2

cm

Surface height 2

15,0

cm

16,5

cm

22,0

cm

16,5

cm

Standard leg for beds with Boxspring in uphols-tered version: on round black standard legs

Two different surface heights, alternative leg versions

Bed with bed surround

Bed with bed surround

Bed with Boxspring

Bed with Boxspring

Surcharge for leg B

Bed accessories

Product information Boxspring

Leg Around leg, different versions, please state the required version clearly in the order!

Leg Bsquare leg, optionally in high-gloss chrome or matt chrome, please state the required version clearly in the order!

LUNIS


Upholstered headboard with functionThe upholstered headboard is available optionally with a function. The top corners can be adjusted forwards to guarantee side support (e.g. for reading in bed).

Surcharge for upholstered head-

board with function

801

-

Upholstered headboard with function

Bed accessories

This luminaire contains built-in LED lamps of the energy classes A++ to A. The lamps cannot be changed in the luminaire. 12 V

Set of 2Swing-out LED bedside reading lamp (set of 2)aluminium colour; for fitting on headboard (left and right). Fitting on upholstered headboard with function is not possible.

978

-

894

-

Ambience lamp for headboard of bed with inside width of:

140 cm 160 cm 180 cm 200 cm

8914

-

8916

-

8918

-

8920

-

Bed lamps

LED bedside lamp (pair)with motion sensor for switching on and off (no time interval)

Ambience lampcan be dimmed; switch on headboard. Fitting on upholstered headboard with function, later fitting or including lamps in combination with headboard panels is not possible.

3 W per metre length

3.0 W

1.8 W



Headboard panel protruding left and right by 73.5 cm(for 76.8 cm wide pedestals)

Ambience lamp for headboard panel protruding left and right by 73.5 cm

Ambience lamp for headboard panel protruding left and right by 99.0 cm

Ambience lamp for headboard panelscan be dimmed; switch in panel (left and right); position of switch:36.0 cm from top rim and 61.0 or 79.5 cm (for 73.5 or 99.0 cm protruding headboard panels) from outer rim of headboard panel

Neither a combination with ambience lamps for bed headboards nor later assembly is possible.

979

-

296 cm316 cm336 cm356 cm

347 cm367 cm387 cm407 cm

min. 296.0 to max. 407.0

73.5 / 99.0 (outer rim of headboard panel to outer side of bed)

85140851608518085200

- - - - - - - -

87140871608718087200

- - - - - - - -

Bed accessories

Headboard panel

140 cm160 cm180 cm200 cm

Lamps for headboard panels

140 cm160 cm180 cm200 cm

Headboard panel protruding left and right by 99.0 cm(for 102.4 cm wide pedestals)

296 cm316 cm336 cm356 cm

347 cm367 cm387 cm407 cm

for bed inside width:

for bed inside width:

Type no.

Type no.

Type no.

Type no.

Price group I Price group II

Price group I Price group II

Set of 2

Headboard panel (standard split in the middle)101.2 cm high, 5.1 cm deep incl. wall mounting bracket; for wall assembly 1.8 cm above floor

All beds can be fitted in front of optional headboard panels. The headboard panels can be enhanced with a comprehensive range of accessories (see below and following pages).

The headboard panels must only be fitted on absolutely solid walls. Light masonry is not suitable for this purpose.Please be sure to note here the information and notes in the “Wall composition” chapter!

Swing-out LED panel reading lamp (set of 2)Housing of lamp in different versions; for fitting on headboard panel (left and right). Position of lamp (top rim of lamp): 9.0 cm from top rim and 55.0 or 77.0 cm (for 73.5 or 99.0 cm protruding headboard panels) from outer rim of headboard panel. Please state the required version clearly in the order!Later fitting is not possible.


1.2 W

----

8514851685188520

----

8714871687188720

Total width:

Total width:

for headboard panel width:

for headboard panel width:


9

55/77

36

61/79,5

LUNIS


--

50512

--

50768

Fitting position of 51.2 cm wide wall consoles Fitting position of 70.0 cm wide wall consoles

Electric socket for headboard panelsPosition of electric socket (centre of socket): 25.6 cm from bottom rim and 61.6 cm or 82.6 cm (for 73.5 or 99.0 cm protruding headboard panels) from outer rim of headboard panel

Later fitting is not possible.

06

-

Wall consoles for headboard panels14.7 cm high;44.8 cm deep

See below for fitting positions of wall consoles!

Max. load: 10 kg

Fitting positions of wall consoles

Please state the required fitting position clearly in the order!

70.0 cm wide wall consoles are not possible with the 73.5 cm protruding headboard panel.

Accessories for headboard panels

Electric socket for headboard panels

Wall consoles for headboard panels1 drawer 1 drawer

51.2 cm wide 70.0 cm wide

Height position 1 for 73.5 cm protruding headboard panels






Price gr.III

25,6

61,6/82,6

6,4 99,0

46,6

6,4 99,0

54,3

19,2 99,0

46,6

19,2 99,0

54,3

73,5

46,6

6,4

73,5

54,3

6,4


Position of 70.0 cm wide angled shelvesPosition of 38.4 cm wide angled shelves Position of 51.2 cm wide angled shelves

Panel carcases with box drawer or flap

Position of panel carcase with box drawer:Can be fitted anywhere in height and width (up to max. 64 cm from outer rim of head-board panels)

Position of panel carcase with flap:Panel carcase can be fitted anywhere on headboard panel (up to max. 64 cm from outer rim of headboard panels)

5128

--

5192

--

51.2 cm wide38.4 cm wide 70.0 cm wide

Angled shelves for head-board panels9.8 cm high14.0 cm deep

See below for positions of angled shelves!

Max. load: 5 kg

Positions of angled shelvesfor 73.5 and 99.0 cm protru-ding headboard panels

Please state the required position clearly in the order!

70.0 cm wide angled shelves can only be fitted in the 99.0 cm protruding headboard panel.

* Distance between top rim of headboard panel and bottom rim of angled shelf

can be fitted anywhere,

depending on headboard

panel width (max. 64 cm)

can be fitted anywhere

(as far as headboard)

Panel carcases for headboard panels

Angled shelves for headboard panels

Accessories for headboard panels

Panel carcase with 1 box drawer;H x W x D: 12.8 x 12.8 x 12.8 cm

Panel carcase with 1 flap;H x W x D: 19.2 x 19.2 x 15.1 cm

5030

--

--

--

5050 5070

Price gr.III

Price gr.III

73,5/99,0

45,8

*

6,4

73,5/99,0 99,0

6,4 6,4

73,5/99,0

6,4

73,5/99,0 99,0

6,4

30,8

*

6,4

30,8

*

30,8

*

45,8

*

45,8

*

LUNIS


Pedestalson 1.8 cm high plinth adjus-ters;16.5 cm high;57.6 cm deep

Consoleson 1.8 cm high plinth adjus-ters;46.6 cm high;44.8 cm deep

If consoles are fitted on pe-destals (see below), the plinth adjusters are omitted.

38.4 cm wide

LED inside drawer lampsConsoles with drawers can be fitted with optional LED inside drawer lamps (7.5 V, 1.0 W powered by standard AAA 1.5 V batteries included - rechargeable batteries not possible; with automatic on/off switch).

Please state exactly in your order which drawer is to be fitted with LED inside drawer lamps.

This type of luminaire is excepted from obligatory labelling in accordance with EU-VO 874/2012 guidelines (Reason: battery-operated and/or < 30 Lumen).

Surcharge for LED inside drawer lamps per drawer:

70.0 cm wide51.2 cm wide

Pedestal console38.4 cm high;44.8 cm deep

for placing on pedestals (see below)

5205

--

5207

--

5203

--

-


51176

--

51110

--

505

-

Consoles

LED inside drawer lamps

Pedestals

70.0 cm wide

Ancillary units

2 drawers2 drawers 1 open compartment; 2 drawers LED lamp for open com-partmentLED lamp incl. footswitch; Magic-Tronic (see page 19) possible at a surcharge.

1 drawer; 1 inside drawer

1 drawer 1 drawer


2.0 W

5207252071

--

as illustr.v. versa

Price gr.III

Price gr.III

Price gr.III


5047

--

50412

--

52128

--

54128

--

54179

--

5605

--

5615

--

53128

--

53179

--

3

High chestson 1.8 cm high plinth adjus-ters;136.9 cm high;44.8 cm deep

Chestson 1.8 cm high plinth adjus-ters;91.4 cm high;44.8 cm deep

128.0 cm wide



Chests

Wall chests

High chests

128.0 cm wide

Ancillary units

4 drawers4 drawers 2 doors

4 drawers

6 drawers Top:1 flap

Bottom:3 drawers


3 drawers 3 drawers

4 drawers

179.2 cm wide

Wall chests64.0 cm high;44.8 cm deep

Max. load 30 kg

The wall chests must only be fitted on absolutely solid walls. Light masonry is not suitable for this purpose. Please be sure to note here the information and notes in the “Wall composition” chapter!

Price gr.III

Price gr.III

Price gr.III

Price gr.III

Assembly notes for wall units:Please be sure to note here the information and notes in the “Wall composition” chapter!

34

LUNIS



522

--

550

--

570

--

5100

--

-

5001

-

5002

-

5003

7617

-

Dressing cheston 1.5 cm high plinth adjus-ters;Total height incl. mirror:122.0 cm;47.0 cm deep

Substructure of metal, powder- coated white, panel and mirror rear side in white lacquer 132.0 cm wide

Angled shelves

Dressing chest1 drawer; panel with mirror and box drawer

Ancillary units

Angled shelves22.6 cm high22.6 cm deep

for fitting anywhere on walls

Max. load: 15 kg

LED lamps for angled shelves: see below! 128.0 cm wide70.0 cm wide51.2 cm wide

LED lamps for angled shelvesLED lamps for angled shelves

for 128.0 cm widthfor 70.0 cm widthfor 51.2 cm width

Magic-TronicThe lamps are normally operated by an external footswitch. As an alternative we can also provide a Magic-Tronic switch, which is charged extra. By “stroking” the outer or top side of the unit at the same level as the invisible integrated sensor it is possible to switch all the lamps on and off (“Stroking method”). As an alternative the position of the hidden sensor can also be marked with a small metal plate on the furniture unit (“Marking method”). Lamps with a maximum power of 200 W can be operated by a Magic-Tronic unit (230 V). The footswitch is omitted when a Magic-Tronic unit is included.

Please be sure to observe the information and notes regarding the assembly position!

LED lamps incl. footswitch. A Magic-Tronic or remote control unit is possible for operation (against a surcharge).

1 W per lamp

Price gr.III

Price gr.III

Price gr.III

The angled shelves may only be fitted on absolutely solid walls. Gypsum or other light masonry is not suitable for this purpose. Please be sure to note here the information and notes in the “Wall composition” chapter!


Possible arrangements

LUNIS


Illustration 1: “Stroking method“

Illustration 2: “Marking method“

The lamps are normally operated by an external footswitch. As an alternative we can also provide a Magic-Tronic switch, which is charged extra. By “stroking” the outer or top side of the unit at the same level as the invisible integrated sensor it is possible to switch all the lamps on and off (“Stroking method”). As an alternative the position of the hidden sensor can also be marked with a small metal plate on the furniture unit (“Marking method”). Lamps with a maximum power of 200 W can be operated by a Magic-Tronic unit (230 V). The footswitch is omitted when a Magic-Tronic unit is included.

Standard position of Magic-Tronic for angled shelves:• for angled shelves of the METIS plus range: sensor is fitted 8 cm from the top rim and 8 cm from the left side in

the rear wall panel• for angled shelves of the LUNIS range: sensor is fitted 16 cm from the rear rim and 9.6 cm from the left side in the

shelf

Standard position of Magic-Tronic for consoles and chests:• for consoles and chests of the LUNIS range: sensor is fitted 16 cm from the rear rim in the cover shelf and 15.0 cm

at the side next to the bed• for consoles and chests of the MULTI-VARIS range: sensor is fitted 12 cm from the rear rim in the outer side next to

the bed and in approx. 7-15 cm from the top rim of the unit

Standard position of Magic-Tronic for MULTI-FORMA II wardrobes:• for hinge- and folding-door wardrobes of the MULTI-FORMA II range: sensor is fitted in the right passepartout in

approx. 130 cm height (Magic-Tronic is not possible for wardrobes without passepartout, in sliding-door wardrobes and in the room and niche system)

Alternative positions:If the Magic-Tronic sensor is to be fitted on the right in the rear wall panel or in the shelf of angled shelves, in the left passepartout of the wardrobe or at any position other than that stated as standard (e.g., if a unit is planned in a niche so that there is insufficient space to the right of the unit), please state this clearly in the order and mark the position in the sketch. If in doubt, please contact your hülsta customer advisor!

Switch options for lamps

Magic-Tronic

Magic-Tronic

Examples of use (schematic diagrams)Black point = Standard position of Magic-Tronic sensor for angled shelves (example 1), consoles and chests (example 2) or hinge- and folding-door wardrobes MULTI-FORMA II (example 3)

Notes:The black point in the drawings is the area where the Magic-Tronic sensor is invisibly integrated. If the surface is „stroked“ at this position, the lamps are switched on or off.

If you would like to mark the position of the Magic-Tronic sensor on the furniture, you can fit a small metal plate supplied separately at the corresponding position.

for hinge- and folding-door wardrobes of the MULTI-FORMA II range

Example 3

for angled shelves of the METIS plus range for angled shelves of the LUNIS range

Example 1

for consoles and chests of the LUNIS range for consoles and chests of the MULTI-VARIS range

Example 2

-

7617


Special widths

Only applies to hinge- and folding-door wardrobes

• Single-door units, left or right hinges, can be reduced down to 25 cm width (apart from profiled doors).• Twin-door units can be reduced at both sides down to 50 cm total width (apart from profiled doors).• Interior fittings such as drawers and other fittings cannot be reduced in width.• For notes on width reductions on MULTI-FORMA II sliding-door wardrobes please see special-sized products

for MULTI-FORMA II!

Special heights, special widths, special depths

Notes on calculating sizes of sloping units

Rear sloping

Rear sloping is possible on all wardrobe units.

Measurements required:H 1 = Room heightH 2 = Height of slope (If a space is required between the wall and the wardrobe/unit,

please state the exact distance.)T 1 = Depth of slopeT 2 = Depth of slope

max. 46 cm

Special heights

• Hinge-, folding- and sliding-door wardrobes can be reduced in height at intervals of 1.0 cm.• Below eye-level we recommend fitting a top cover shelf made of panelling material.

Please state in order!• Special heights in stepped versions (not possible on sliding-door wardrobes) at a surcharge.

Surcharge per step:

Special depths

• Depth reductions are made on side sections, plinths, cornices and shelves.• Interior fittings such as drawers and other fittings cannot be reduced in depth.• A max. reduction of 30.0 cm is possible on hinge- and folding-door wardrobes.• A max. reduction of 9.0 cm is possible on profiled hinge-doors.• For sliding-door wardrobes, a max. reduction of 30.0 cm is possible (max. 18 cm in combination with the electrical opening

system for MULTI-FORMA II).• Please note that for technical production reasons not every special depth can be achieved:

2.5 cm standard reduction between 0 and 2.5 cm 5.0 cm standard reduction between 4.5 and 5.0 cm 27.5 cm standard reduction between 27.0 and 27.5 cm

Special-sized products

Side sloping

Sloping is only possible on single-door units. The door hinge (left or right) is positioned on the taller outer side of the unit.

Measurements required:H 1 = Room heightH 2 = Height of slope (If a space is required between the wall and the wardrobe/unit,

please state the exact distance.)B 1 = Width of slopeB 2 = Width of slopeG = Total widthS = Wardrobe width

Please note!• If the slope cuts across the position of a handle, the handle of this door only is positioned further

down in production.• As floors, ceilings and walls are never exactly straight, the exact room size must be measured using

a spirit level.• If a cornice is fitted, please state if this is to be continued in the sloping section.

-

00030

LUNIS



LUNISWardrobes

Special heights:Hinge-door - WoodHinge-door - Mirror

Special widths:for single-door unit - Woodfor single-door unit - Mirrorfor twin-door unit - Woodfor twin-door unit - Mirror

When ordering extra fitted shelves and clothes rodsSize reduction surcharge per fitted shelfSize reduction surcharge per clothes rod

Special depths:Surcharge per unit

When ordering extra fitted shelvesSize reduction surcharge per fitted shelf

Side sloping:Surcharge per unit without cornice in the slopeSurcharge per unit with cornice in the slope

Side sloping is possible up to a minimum height of 88.0 cm.

Rear sloping:Surcharge per unit

Ancillary units

Special heights (drawers not possible in special height and not possible on high-gloss versions)CarcaseDoorChest of drawers in drawer raster

Special widths (not possible on high-gloss versions):CarcaseDoorDrawerPedestalHeadboard panel


Special widths are not possible on panel carcase and on angled shelves (for headboard panels).

Special depths (drawers not possible in special depth):Carcase


Beds

Bed in special length 190 cmUpholstered headboard in special heightBed with two footboards (all-round bed; only for beds with bed surround frame in wood/lacquer/ high-gloss version)

Special-sized products for special combinations:Pricing: special combination + 15% plus all the required special-sized products (see above)

More special products are possible. Please get in touch with your customer advisor.

without surcharge

000300031

----

000500051000600061

--

99919992

-0007

-9993

-9994

-99916

-99912

--

9990299903

-99902

-----

9991209991309991709993099925

-999141

-99932

-999341

--

9996499965

99967

without surchargewithout surcharge



Special articles

High-gloss care setPolish, polishing sponge and polishing cloth (incl. instructions) for protecting and maintaining the high-gloss surfaces

Edge veneerfor veneered/lacquered versions per m. length

165° hingesWardrobe doors can also be fitted with 165° hinges against a surcharge (only possible on plain, straight hinge-doors; impossible on fabric-covered doors and accent fronts). Please mark the doors clearly in the order!

Surcharge for 165° hinges per hinge-door:

Panels for side and top covering of fitted wardrobes (not possible for high- gloss versions; support construction and fitting materials must be acquired on site).

For veneered/lacquered versions (max. 268.0 cm long, max. 59.0 cm wide, 2.0 cm thick)Basis charge per order:+ price per m² - lacquer+ price per m² - veneerVeneer match with fronts can not be guaranteed.

Wardrobe doors are also available as separate units and are charged as follows:

For 1 hinge-door/folding-door wing: 50% of the concerning 1-door hinge-door extension unit

For 1 sliding-door including mechanism: 35% of the twin-door sliding-door wardrobe

For door superstructures, type 100 (max. 98 cm wide, only for assembly between wardrobes): 100% of twin-door hinge-door extension unit

9901 -990 -990 -

9902 -

180 -

36 -

Special colours; Note on „Blue Angel“ / Emissions label of DGM

Special coloursAll the hülsta lacquer colours are possible for nearly all the hülsta ranges. Availability and prices on request.

Note on „Blue Angel“ (RAL-UZ 38) and Emissions label of DGM (Class A)It is possible that the requirements of the „Blue Angel“ and the DGM Emissions Label can-not be met by some of the lacquer colours in price groups II and III (see here the different lacquer versions in the NURIA range), depending on the colour mix (surface ratio of these colours in the corresponding order). However, the legal requirements are definitely met in all cases!

Individual special-sized productsIf the special-sized product that you require is so unusual that it cannot be illustrated with the many special sized products that we already provide and charge for, then we will quote you the price using a HK unit type factor. In your order please state for us the relevant enquiry number and the HK unit type factor stated.

-HK

LUNIS


Note on usable bed inside height:The support slats of the hülsta beds are delivered in the centre position, i.e. they can be adjusted by 3.2 cm upwards and downwards (exception: for LUNIS beds in the standard surface height 1 only by 3.2 cm upwards). If the slats are set in the lowest position, the maximum usable bed inside height is achieved. In the case of some beds, the bed inside height is comparatively low. This means that mattresses in combination with base frames that are somewhat higher are not held so well by the bed side sections. Please note that the usable bed inside height of beds with height adjustable support slats is reduced when these are set higher.

This is how to calculate the individual height from the data supplied with the base frames:

Note on space under bed:The storage space underneath the base frame is calculated from the bed height minus the usable bed inside height.

Example bed: 42.2 cm - 18.0 cm = 24.2 cm.

Max. usable bed inside height:18.0 cm

approx. 12.5 cm for holding mattress

5.5 cm total height of base frame (example: hülstaflex basic B)

Example (for all beds): bed and hülstaflex basic B base frame (back and foot sections adjustable)

Usable bed inside height and space under bed

{

LUNIS bed in standard surface height 1 and hülstaflex basic B base frame (back and foot sections adjustable)

Max. usable bed inside height:14.0 cm

approx. 8.5 cm for holding mattress

5.5 cm total height of base frame (example: hülstaflex basic B)

{


Labelling in type list drawings / assembly notes for wall unitsThe majority of units have two wall mounting points (= number of support boards), if these are to be fitted as wall units. This is not explicitly mentioned in the type list. If a diffe-rent number of wall mounting points (= support boards) is required, this is marked in the drawings in the type list with numbers in black boxes. Every support board requires four mounting screws.

One assembly mortar set is sufficient for up to a maximum of 3 support boards or 4 wall side-panels.

Important note: Depending on the composition of the wall (see wall types illustrated above), assembly must be carried out using the special assembly mortar set and a standard trade mastic tool which are the basic essentials for safe and clean workmanship.

Wall composition / assembly instructionImportant notes:The composition of walls must be ascertained before concluding a contract and be checked by a qualified fitter before assembly takes place.

Assembly may only be carried out by a qualified fitter under careful observation of the assembly instructions.

The plastic Rawl plugs supplied by hülsta as a standard set are only suitable for concrete ≥ C12/15, if the wall composition and compression strength corresponds to the table below. Under no circumstances must a unit be assembled on light masonry.

Furthermore, we provide a mounting set with assembly mortar for the types of walls listed below (see assembly mortar set below). Again, assembly must be carried out by a qualified fitter under careful observation of the wall composition and assembly instruction. The compression strength levels stated below must be met under all circumstances.

Assembly mortar set for up to a maximum of 3 support boards consisting of:

9x injection retaining sleeve9x screw-in sleeve1x injection cartridge2x static mixer1x assembly instructions

Please use the mounting screws from the standard set (supplied free of charge).

Mounting sets

Standard setThe standard set consists of 4 plastic Rawl plugs and 4 mounting screws and is sufficient for 1 support board. The standard sets are included in the packet of fittings to match the number of support boards.

34

= 3 support boards= 4 support boards, etc.

Building bricks Mz 12Compression strength ≥ 12 N/mm²

Limestone blocks KS 12Compression strength ≥ 12 N/mm²

Perforated sand lime bricks KSL12Compression strength ≥ 12 N/mm²

Vertically perforated bricks HLz 12Compression strength ≥ 12 N/mm²Bulk density ≥ 1.0 kg/dm³

Concrete C12/15Compression strength ≥ 15 N/mm²

Assembly mortar set only suitable for the materials stated below!Standard set

Solid blocks of light concrete V2Compression strength ≥ 2 N/mm²

Perforated blocks of light concrete Hbl 2Compression strength ≥ 2 N/mm²

Aerated concrete PP2Compression strength ≥ 2 N/mm²

Materials tablewith a description of which sets are to be used with the following types of walls:

Example of order:

• Add up number of support boards for all existing unit types

• Divide the sum by “3”

• Round up the result to a full number

= Number of assembly mortar sets required

Important notes

-

M2

A different and more suitable type of mounting must be chosen by a qualified fitter in all other cases. hülsta cannot accept any responsibility for the choice of any other types of mounting! Please note that if the units are not mounted properly on the wall, there is a risk of the units falling down or tipping over – especially when alternative mounting materials acquired on site have been used. Generally speaking, you as a dealer/qualified fitter are responsible for the correct wall mounting of the units.

LUNIS


Notes

Design and concept legally protected, subject to error and alterations to construction, colour and materials by way of technological progress.

Stand:

hülsta LUNIS

Your Hotline to hülsta

Lots to do? A customer wants his project finished and you haven’t got enough time? Or the project is so complex that it will take too much time?

This is exactly the kind of situation we created the hülsta Planning Service for. hülsta’s employees create the required project for you at short notice. Based on your information, we implement the project perfectly with all views and a complete order list ready for immediate forwarding to the customer.

The hülsta check list (available at https://www.huelsta.com/einrichtungsberatung/) makes it all really easy for you. You won’t forget anything with this list and the customer receives a project he will be thrilled about as quickly as possible.

Our Saturday hotline is available all day from 10.00 a.m. until 6.00 p.m.

Telephone: +49 (0) 2563 / 86-1800

On working days the hülsta Sales Department is available all day from 8.00 a.m. until 6.00 p.m.

hülsta Planning Service

Special wishes? Come to us!

We are open Saturdays for you, too!

E 9. 2019

Maximum individuality! – Maximal flexibility! – hülsta makes most of your special wishes possible.And if you do have a wish which is not quite so easy to implement, just give us a call or send us a mail or a fax. We have our own hülsta “Special Wishes Team” who are there to help you realise just these customer requests. These colleagues are professionals when it comes to special products. They plan and calculate the products possible for you and even develop an alternative suggestion if the idea should turn out to be technically impossible.

Here is an overview of the hülsta range of special wishes:• A lot of special products can be ordered simply via the type list• Special-sized products are planned simply and professionally• Competent colleagues advise you by phone, by fax and by mail• You will be sent alternative suggestions if the idea is technically impossible• Many special-sized products are available without a surcharge• Specially qualified carpenters and technicians implement your plans perfectly

Do you have any questions or require any alterations to your order confirmation?Do you have any questions on our products or your current order?Do you have any complaints about supplied goods or required replacement parts?Contact Telephone: +49 (0) 2563 / 86-1144 • email: [email protected]

Do you have any questions, suggestions or wishes for the hülsta Marketing team or the hülsta product seminars?Contact Telephone: +49 (0) 2563 / 86-1611 • email: [email protected]

hülsta Planning ServiceTel.: +49 (0) 2563 / 86-0

Fax: +49 (0) 2563 / 86-2666Mail: [email protected] from 8.00 a.m. until 6.00 p.m.

hülsta Special Wishes TeamTel.: +49 (0) 2563 / 86-0

Fax: +49 (0) 2563 / 86-1417Mail: [email protected]

hülsta-werke · Karl-Hüls-Straße 1 · D-48703 StadtlohnTel. +49 (0) 2563 / 86-0 · Fax +49 (0) 2563 / 86-1000

www.huelsta.com

sleeping...• beds in 2 different surface heights • comprehensive bed accessories: different...

Documents