skscr3001p 30-inch integrated column refrigerator-spec sheet · 2020. 7. 6. · refrigerator. allow...
TRANSCRIPT
© 2020 Signature Kitchen Suite. All rights reserved. Design, features and specifications are subject to change without notice. Specifications are for planning purposes only. Consult the product’s installation instructions for final dimensional data and other details prior to making cutouts or custom panels. Consult with a heating and ventilation engineer for your specific ventilation requirements. Non-metric weights and measurements are approximate. Smart features require Internet access. 1-855-790-6655 | www.signaturekitchensuite.com
Page 1 of 5 | Effective 7/20 | WCAG
SKSCR3001P30-INCH INTEGRATED COLUMNREFRIGERATOR
StyleDoor Style Panel ReadyInterior Cabinet Finish Metal
InnovationWi-Fi-Enabled for ThinQ® Control with iPhone / Android App
Yes
Remote Operations YesInverter Linear Compressor Yes
PerformanceSpeed Chill YesModesSabbath, Demo, Power On / Off, Temp Control, Water Filter Reset, Smart Diagnosis, WiFi, Smart GridInternal Water Dispenser YesWater Filter (6 Months) Yes
Capacity and StorageTotal Capacity (cu. ft.) 18.0Storage Shelves 3 Adjustable
w/LED Lighting, 1 Fixed
Adjustable / Removable Storage Drawer
1 Soft Close / Self Close
Lift and Go™ Crisper / Storage Drawers 2 Soft Close / Self Close
Aluminum Framed Lift and Go™ Door Bins with Removable Inserts (Holds 2-Liter Bottles)
4 Adjustable
LARGEST CAPACITY COLUMNDesigned to provide the largest capacity in the industry*, the 30-inch Integrated Column Refrigerator features 18.0 cu. ft. of storage capacity.
PRECISE PRESERVATIONIngenious features like an Inverter Linear Compressor and metal interior help to minimize temperature fluctuations to within 1° F to maintain food freshness.
SIGNATURE FIT™ INTEGRATED DESIGNEvery integrated column features an intelligent, symmetrical design that allows for flush installation, along with easy door reversal. Also, when installed with the 18-inch Integrated Column Freezer, the pair cleanly fits a 48" opening or a 47.5" opening—perfect for both new construction and replacement applications. (See Integrated Column Planning/Installation Guide for details)
INTERNAL WATER DISPENSERThe internal water dispenser delivers cold, fresh, filtered water with a simple touch.
ECO FRIENDLYEngineered to reduce environmental impact with HFC / HCFC free refrigerant, insulation and recyclable materials.
*Based on survey of comparable products performed March 1, 2020.
Modes Sabbath, Demo, Power On / Off, Temp Control, Water Filter Reset, Smart Diagnosis, WiFi, Smart Grid
*These warranties give you specific legal rights and you may have other rights that vary from state to state. For complete warranty details, refer to your Use & Care manual.
Page 2 of 5 | Effective 7/20 | WCAG
SKSCR3001P30-INCH INTEGRATED COLUMNREFRIGERATOR
Technical SpecsRequired Power Supply 115 V, 60 Hz,
15 AmpPlug Type 3-ProngPower Cord Length 86 1/2"
Dimensions and WeightOverall Width (inches) 29 3/4"Overall Height (inches) 83 1/2" Min. –
84 1/2" Max.Overall Depth Without Panel or Handles (inches)
23 7/8"
Net Weight (approx.) 385 lbs.Shipping Weight (approx.) 427 lbs.
Optional AccessoriesStainless Steel Panel / Handle / Toekick Kit
SKSPK305CS
Retrofit Frame Kit SKSFK800CSBrushed Aluminum Handle
Medium – 31 11/16" SKSHK310HSLong – 48" (For Columns) SKSHK480HS
Replacement Water Filter LT1000P-S
Warranty Summary*Limited Warranty, Parts & Labor 3 YearsLimited Warranty on Sealed System, Parts and Labor
5 Years
Limited Warranty on Sealed System, Parts Only
10 Years
General FeaturesDigital Controls w/White LED Display YesWater Filter Indicator YesHidden LED Interior Lighting YesOperating Temperatures 33° to 46° FMaximum Sound Level 39 dBA Star-K Certified Sabbath Mode YesENERGY STAR® Certified Yes
Installation FeaturesReversible Door YesFour Point Front Adjustable with 8 Wheels
Yes
Attachment Method to Cabinetry Top with No Visible Screws
Front Serviceable YesAnti-tip Bracket Included Yes
30" (762 mm) finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCR3001P30-INCH INTEGRATED COLUMNREFRIGERATOR
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
1 3/8" (35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
30" (762 mm) finished width
CUTOUT DIMENSIONS – RETROFIT INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
1 3/8"(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
3/4"(19 mm)**
115°
90°
1/8"(3 mm)
1/8"
min. min.(3 mm)
29 3/4"(756 mm)
30" (762 mm)
25"(635 mm)
13 7/8"*(352 mm)
31 1/2"(800 mm)
1 1/4"*(32 mm)
5"(127 mm)electricallocation
4"(102 mm)
water location
5"(127 mm)electricallocation
4"(102 mm)
water location
25" (635 mm)min. depth
84"(2134 mm)
24" (610 mm)min. depth
84"(2134 mm)
CUTOUT DIMENSIONS – FLUSH INSTALLATION
Notes
Refrigerator can be installed flush with 3/4" custom panel or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the refrigerator fits flush with 25" (635 mm) depth adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for water dispenser operation. Water pressure must be between 20 and 120 p.s.i.
Tubing should be long enough to extend to the front of the refrigerator. Allow enough tubing to accommodate a bend leading into the water line connection.
Water line can enter an opening through floor or back wall.
SINGLE COLUMN
Notes
Door Swing Clearances – The installation must allow for clearances to adjacent walls or cabinets. This refrigerator is equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the dimension noted to determine the total clearances required from adjacent cabinets or walls. This clearance will vary depending on the custom handle used. When using the Stainless Steel Door Panel Kit w/Handle or the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 16" (406 mm).
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
30" (762 mm) finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCR3001P30-INCH INTEGRATED COLUMNREFRIGERATOR
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
1 3/8"(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
30" (762 mm) finished width
CUTOUT DIMENSIONS – RETROFIT INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
1 3/8"(35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
3/4"(19 mm)**
115°
90°
1/8"(3 mm)
1/8"
min. min.(3 mm)
29 3/4"(756 mm)
30" (762 mm)
25"(635 mm)
13 7/8"*(352 mm)
31 1/2"(800 mm)
1 1/4"*(32 mm)
5"(127 mm)electricallocation
4"(102 mm)
water location
5"(127 mm)electricallocation
4"(102 mm)
water location
25" (635 mm)min. depth
84"(2134 mm)
24" (610 mm)min. depth
84"(2134 mm)
Page 3 of 5 | Effective 7/20 | WCAG
SKSCR3001P30-INCH INTEGRATED COLUMNREFRIGERATOR
CUTOUT DIMENSIONS – FLUSH INSTALLATION SINGLE COLUMN
A minimum 4" (102 mm) finished return that matches the cabinet * exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
NotesRefrigerator can be installed flush with 3/4" custom panel or optional stainless steel panel kit. With a 25" (635 mm) cutout depth, the front face of the refrigerator fits flush with 25" (635 mm) depth adjacent cabinets. Electrical
A 115V, 60Hz., 15 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown. Note: GFI (ground fault interrupter) is not recommended.
Water LineA cold water supply is required for water dispenser operation. Water pressure must be between 20 and 120 p.s.i. Tubing should be long enough to extend to the front of the refrigerator. Allow enough tubing to accommodate a bend leading into the water line connection.
Water line can enter an opening through floor or back wall.
INSTALLATION CLEARANCES – FLUSH INSTALLATION TOP VIEW
* Door handle must be added to this dimension.
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Notes
Door Swing Clearances – The installation must allow for clearances to adjacent walls or cabinets. This refrigerator is equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted. Door Handle Clearances – The Door Handle depth must be added to the dimension noted to determine the total clearances required from adjacent cabinets or walls. This clearance will vary depending on the custom handle used. When using the Stainless Steel Door Panel Kit w/Handle or the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 16" (406 mm).
Page 3 of 5
31 3/8"(797 mm)
29 3/4"(756 mm)
29 3/4" (756 mm)
FRONT VIEW
OVERALL PRODUCT DIMENSIONS
SKSCR3001P30-INCH INTEGRATED COLUMNREFRIGERATOR
SIDE VIEW
24 3/4"*
22"***
23 7/8"**
(629 mm)
(558 mm)
(607 mm)
4"
5"(127 mm)
(102 mm)
Depth with 3/4" (19 mm) door panelDepth with door (no panel)Unit depth without door
***
***
9" (229 mm)
3/4" (19 mm)
TOP VIEW DOOR OPEN 90˚
TOP VIEW DOOR OPEN 115˚
34"(864 mm)
29 3/4"(756 mm)
83 1/2"
min.
84 1/2"
(2121 mm)
(2146 mm)81 9/16"
80 9/16"
(2072 mm)
(2046 mm)
max.
min.
max.
Unit width without door panel
Unit width without door panel
Unit width without door panel
31 3/8"(797 mm)
29 3/4"(756 mm)
29 3/4" (756 mm)
FRONT VIEW
OVERALL PRODUCT DIMENSIONS
SKSCR3001P30-INCH INTEGRATED COLUMNREFRIGERATOR
SIDE VIEW
24 3/4"*
22"***
23 7/8"**
(629 mm)
(558 mm)
(607 mm)
4"
5"(127 mm)
(102 mm)
Depth with 3/4" (19 mm) door panelDepth with door (no panel)Unit depth without door
***
***
9" (229 mm)
3/4" (19 mm)
TOP VIEW DOOR OPEN 90˚
TOP VIEW DOOR OPEN 115˚
34"(864 mm)
29 3/4"(756 mm)
83 1/2"
min.
84 1/2"
(2121 mm)
(2146 mm)81 9/16"
80 9/16"
(2072 mm)
(2046 mm)
max.
min.
max.
Unit width without door panel
Unit width without door panel
Unit width without door panel
OVERALL PRODUCT DIMENSIONS
TOP VIEW
FRONT VIEW
DOOR OPEN 90°
SIDE VIEW
DOOR OPEN 115°
Page 4 of 5 | Effective 7/20 | WCAG
SKSCR3001P30-INCH INTEGRATED COLUMN REFRIGERATOR
OVERALL PRODUCT DIMENSIONS
FRONT VIEW
Unit width without door panel
SIDE VIEW
* Depth with 3/4" (19 mm) door panel ** Depth with door (no panel)
*** Unit depth without door
TOP VIEW
DOOR OPEN 90°
Unit width without door panel
DOOR OPEN 115°
Unit width without door panel
Page 4 of 5
OPTIONAL ACCESSORIES
SKSCR3001P30-INCH INTEGRATED COLUMNREFRIGERATOR
OPTIONAL ACCESSORIES
SKSPK305CS – Stainless Steel Panel Kit for 30-inch Integrated Column Refrigerator
This unit can be installed with an optional Stainless Steel Panel Kit. Kit includes one door panel, one toe kick and one handle. This kit is reversible and can be used in both Right Hand and Left Hand door swing installations.
Handles for Use With Custom Panels
SKSHK310HS – 31 11/16" (805 mm) Medium Handle – Brushed Aluminum
SKSHK480HS – 48" (1219 mm) Long Handle – Brushed Aluminum
Page 5 of 5 | Effective 7/20 | WCAG
CUSTOM PANEL DIMENSIONS
Notes
These units are designed to be customized with decorative panels. Field-installed custom door panels or an optional Stainless Steel Panel Kit is required.
For Custom Panels: Use templates provided with units to pre-drill holes for mounting panel brackets (provided with unit). Adjustment screws and instructions also provided with units.
Maximum Total Door Panel Weights: 30-Inch Integrated Column – 64 lbs.24-Inch Integrated Column – 53 lbs.18-Inch Integrated Column – 44 lbs
Design Tips
4" (102 mm) will be visible on the interior sides of the furniture return. It is recommended that both sides of each cutout panel be finished to match the cabinet exterior.
If using custom panels, a custom toe kick is required. The bottom of case is unfinished.
Door Handles: Handles are not included with the units. Custom handles are required for installation. Brushed Aluminum Handles are available as an optional accessory.
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
47 3/4"(1213 mm)
(756 mm)29 3/4"
DUAL 18" AND 30" COLUMN DUAL 24" AND 30" COLUMN
SKSCR3001P30-INCH INTEGRATED COLUMNREFRIGERATOR
Door Panel Door Panel 79 7/8"(2029 mm)
(451 mm)17 3/4"
53 3/4"(1365 mm)
(756 mm)29 3/4"
Door Panel 79 7/8"(2029 mm)
(603 mm)23 3/4"
Door Panel
DUAL 30" AND 30" COLUMN
59 3/4"(1518 mm)
(756 mm)29 3/4"
Door Panel 79 7/8"(2029 mm)
(756 mm)29 3/4"
Door Panel
4" (102 mm) 4" (102 mm) 4" (102 mm)
(756 mm)29 3/4"
Door Panel 79 7/8"(2029 mm)
4" (102 mm)
Door Panel
(451 mm)17 3/4"
4" (102 mm)4" (102 mm)
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
47 3/4" (1213 mm)
DUAL 18" AND 30" COLUMN
79 7/8"(2029 mm)Door Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
(603 mm)23 3/4"
79 7/8"(2029 mm)Door Panel
(451 mm)17 3/4"
(756 mm)29 3/4"
Door Panel
Refer to the Integrated Column Planning/Installation Guide for details on installing multiple columns, door swing dimensions, cabinet planning, retrofit installation and more.
SKSCR3001P30-INCH INTEGRATED COLUMNREFRIGERATOR
CUSTOM PANEL DIMENSIONS
Notes
These units are designed to be customized with decorative panels. Field-installed custom door panels or an optional Stainless Steel Panel Kit is required.
For Custom Panels: Use templates provided with units to pre-drill holes for mounting panel brackets (provided with unit). Adjustment screws and instructions also provided with units.
Maximum Total Door Panel Weights:
30-Inch Integrated Column – 64 lbs. 24-Inch Integrated Column = 53 Ibs.
18-Inch Integrated Column — 44 Ibs
Design Tips 4" (102 mm) will be visible on the interior sides of the furniture return. It is recommended that both sides of each cutout panel be finished to match the cabinet exterior.
If using custom panels, a custom toe kick is required. The bottom of case is unfinished.
Door Handles: Handles are not included with the units. Custom handles are required for installation. Brushed Aluminum Handles are available as an optional accessory.
OPTIONAL ACCESSORIES
SKSPK305CS – Stainless Steel Panel Kit for 30-inch Integrated Column Refrigerator
toe kick and one handle. This kit is reversible and can be used in both Right Hand and Left Hand door swing installations. Handles for Use With Custom Panels
SKSHK310HS – 31 11/16" (805 mm) Medium Handle – Brushed Aluminum
SKSHK480HS – 48" (1219 mm) Long Handle – Brushed Aluminum
Refer to the Integrated Column Planning/Installation Guide for details on installing multiple columns, door swing dimensions, cabinet planning, retrofit installation and more.
Page 5 of 5 |