side view bonanza a-36 - bigplanes-rc-big-scale … wire copper joiner aluminum tube clevis add a...
TRANSCRIPT
Bonanza A-36
Specification:Length :1632 mm(64.3")Wing Span :2045 mm(80.5")Wing Area :60.0 sq. dm 6.46 sq. ftWing Loading :106.7 g/sq. dm 34.9 oz/sq. ftFlying Weight :6.4 kg(14.1 lbs)Radio :6ch&9 servosEngine :108 2-cycle 120 4-cycle
SAFETY PRECAUTIONS
INSTRUCTION MANUAL
First-time builders should seek advice from people having building experience.If misused or abused,it can cause serious bodily injury and damage to property.Fly only in open areas and preferably at a dedicated R/C flying site.We suggest having a qualified instructor carefully inspect your airplane before its first flight.Please carefully read and follow all instructions included with this airplane,your radio control system and any other components purchased separately.
(The people under 18 years old is forbidden from flying this model)This R/C airplane is not a toy!
132mm
Top view
Side View
20mm
20mm
RUDDER
3-waypressure inlet
Air tank
3-waypressure inlet
3-waypressure inlet
3-waypressure inlet
3-waypressure inlet
Switch
Air inlet
Strut
Strut
Strut
Quick release connector
Make sure to assemble retracts as instructed below.
Three wheel retract system
Quick release connector
Pressure reduction inlet
Ø1.7mm
Ø0.2mm
The status when thegear up
Pull out length of 8mm to make gear down
Air valve Air valve3-way pressure inlet 5
1Air tank
1Air inlet
2
1
1Air line (3000mm)
2Quick release connector
Strut ( 90 )1Strut ( 110 )
Switch
ClevisRod (2X300mm)
1
11
Retainer
TP Screw(2.6x14mm) 2
Top view
Position forright diagram.
ELEVATOR
Side View
30mm
30mm
Top view
25mm
25mm
35mm
AILERON
FLAP
Side View
FLAPAILERON
Pleas notice the inner diameter for each side of the pressure reduction inlet.
Please insure the sealing of the retract system before flight .
Centre of Gravity.Adjustment.
Adjustment. Adjustment.
14
7170
7372
Stee l w i reCopper joiner
Aluminum tube
Clevis
Add a rubber ring to theclevis for insuring safety
Collar (5mm)
Collar (5mm)
Collar (5mm)
Two nacelle bottom covers are supplied for optional assembly of door,which is decided by customers.Hardware package is not included.
TP Screw (2.3x12mm)
6TP Screw (2.3x12mm)
Collar 4mm 3
4Wooden Block(25x15x13mm)
2
7Collar (5mm)
Wheel (90mm)
Wooden supporter(41.5x28x26mm)
Landing gear(5mm)2
1
8TP Screw (3x20mm )Landing gear straps 2Gear door2
1Landing gear (5mm)
1Wheel (75mm)Wooden supporter (46x28x14mm) 1
4TP Screw (2.6x14mm )
TP Screw (3x20mm)
Wooden Block
TP Screw (2.6x14mm)
Collar (5mm)
Wooden supporter
Collar (5mm)
6TP Screw (2.3x12mm)
1Ally nose arm
Epoxy the fixed laning gear to main wing.
Install the wheel to the nose gear.
Epoxy the fixed nose landing gear to the fuselage.
Trim the nacelle bottom cover and assemble it with TP screws.
Installl the wheel and gear door to the landing gear.65
66
67
68
69
13
65
Accessory list for the coming installation steps.
: 4-cycle .120
15"X7
Spinner nut
6
(with 9 servos),6
6
6 channel radio for aiplane is highly recommended for this model.
WarningRemove the covering with proper pressure to cut through only the covering itself.Otherwise,cutting down into the balsa structure may weaken the model part and cause accident.
The pre-covered film on ARF kits may wrinkle due to variations of temperature.Smooth out as explained right.
Pre-cover the covering with clean cloth!Start at low setting. Increase the setting ifnecessary.If it is too high,you may damagethe film.
Iow settingwith cover(cloth)
1.5mm
9TP Screw (2.3x8mm)
Ply (15x15x3mm)9
Epoxy plies inside the fuselage under the cowing and mount the cowing with TP screw as illustration.
9TP Screw (2.3x8mm)
Ply (15x15x3mm) 9
pvc part 1
pvc part 2
pvc part 2
pvc part 2
pvc part 2
Epxy the canopy to the fuselage.Trim the cowling for engine and muffler.
Assemble the cowling .
Cut away the surplus parts of plastic cover carefully along the shaded line.
The side view of the plane.
63
61
62
64
12
60
Accessory list for the coming installation steps.
Securely glue together. If coming off during flights, you 'lllose control of your airplane which leads to accidents!
Make sure hinges are mounted in the same line.
1mm
Aileron
Tailing edge
Make sure they are inthe right position whileinstalling.
6Pin hinge(24x24mm)
8
6
22
2
4
2
2
2
2
Clevis
Rod (2x300mm) Retainer
TP Screw (2.3x12mm)
Wooden Block(20x20x8mm)Servo tray(68.5x56.5x2mm)
Pin hinge(24x24mm)
Screw (3x45mm)
Washer(3x15mm)
2Washer(3x15mm)Lock Nut (3mm )
Clevis
Retainer Rod (2x300mm)
Screw (2x10mm)
Install the servo as the illustration below.
Install the nylon control horn and connect the linkage.
Apply instant type CA glue to aileron and pin hinge.
Keep some space about 1mm width between aileron and trailing edge.
Assemble the aileron to main wing with instant type CA glue.Be careful to ensure the moving parts of the hinges are able to move freely.
1
2
3
4
5
1
Accessory list for the coming installation steps.
1.5mm
2mm
Securely glue together. If coming off during flights, you 'lllose control of your airplane which leads to accidents!
Flap
TP Screw (2.3x12mm)
Make sure hinges are mounted in the same line.
1mm
Tailing edge
Make sure they are inthe right position whileinstalling.
6Pin hinge(24x24mm)
8
6
22
2
4
2
2
2
2
Clevis
Rod (2x300mm) Retainer
TP Screw (2.3x12mm)
Wooden Block(20x20x8mm)Servo tray(68.5x56.5x2mm)
Pin hinge(24x24mm)
Screw (3x50mm)
Washer(3x15mm)
2Washer(3x15mm)Lock Nut (3mm )
Rod (2x300mm)
Clevis
Washer(3x15mm)
Washer
Lock Nut (3mm )
Screw (3x35mm)
Screw (2x10mm)
Install the servo.
Secure the servo. Install the nylon control hornand connect the linkage.
Apply instant type CA glue to flap and pin hinges.
Keep some space about 1mm width between trailing edge and flap.
Assemble the flap to main wing with instant type CA glue. Be careful to ensure the moving parts of the hinges are able to move freely.
7
6 8
9
10
2
Accessory list for the coming installation steps.
TP Screw (2.3x8mm)
1.5mm
8TP Screw (2.3x8mm)Ply (15x15x3mm)
8
Clevis
Rod (2X300mm)
1
1
1
1
Retainer
Ring
10mm
1mmLock Nut (2mm )
Screw (2x10mm)
Ball joint
Washer(2x5mm)
2
2
ClevisCopper joiner
22
Screw (2x10mm) Nut (2mm )
2Washer(2x5mm)
Stee l w i re
Copper joinerLock Nut (2mm )
Screw (2x10mm)Ball joint
Washer(2x5mm)
Install the servo of rudder .
Elevator servo
Rudder servo
Nose gear servo
Throttle servo
Switch servo
The sketch map when the servos install completion.
Mount the receiver and the battery in the fuselage.
Install the nylon control ring for switch and connect the linkage.Assemble the tail gear cover with screw.
Install the servo of elevator and make sure the pushrod can't be pulled out from the copper joiner.
Customer can drill a hole to the copper joiner and fix a pin in it for stopping the pushrod from pulling out.
55
54
56
58
57
11
59
22mm3mm
2Plastic tube(3x850mm)
3mm
145mm10mm
10mm
5mm
Metal arms
Ball joint
Pin
F iberg lass pushrod10mm
1mm
Copper joiner
Epoxy the fiberglass pushrod to relevantposition in the fuselage.
F iberg lass pushrod(3x895mm)1
4Copper joiner
2Plastic tube(3x850mm)
4Ply(20x16x2mm)
24
Copper joiner
Aluminum tube(3x6mm)
2Steel wire (0.5x1500mm)
42
2
2
ClevisRetainer
Washer(3x15mm)
Lock Nut (3mm )
1Screw (3x80mm)
2Clevis
2Screw (2x10mm)
2Nut (2mm )
2Washer(2x5mm)
Washer(3x15mm)Screw (3x80mm)
Lock Nut (3mm )Clevis
Aluminum tube
Stee l w i re
2Steel wire (0.5x1200mm)13
22
ClevisRetainer
Washer(3x15mm)Lock Nut (3mm )
1Screw (3x80mm)2Copper joiner
Rod (2X300mm) 1
The sketch map after the rudder shaft assemble finished.
Assemble the plastic tubes through the holes in the frame,epoxy them and Cut off the surplus parts as show in the illustration.
Drill a hole to appropriate position in the rudder and assemble the rudder shaft.
Epoxy the fiberglass pushrod to the copper joiner tightly.
Customer can drill a hole to the copper joiner and fix a pin in it for stopping the pushrod from pulling out.
49
50
52
53
10
51Accessory list for the coming installation steps.
1.5mm
3mm
TP Screw (2.3x12mm)
Note:rubber wheels oleo struts and retracts are optional.
Retracts strut
Screw (3x10mm) Gear door
Washer(3x6mm)
Main wing joiner 1
1
2Gear door
2Wheel (90mm)
8TP Screw (2.6x14mm)
Washer(3x6mm)
2
2Wood dowel (6x50mm)
2Wood dowel (6x30mm)
22Blind Nut (6mm)
Screw (6x50mm)
Screw (3x10mm) 8
8
LockNut (4mm)
LockNut (4mm)
4Wooden Block(25x15x13mm)
Wooden Block
Clevis
Retainer Rod (2x300mm)
Rod (2x300mm)
Clevis
Washer(3x15mm)
Washer
Lock Nut (3mm )
Screw (3x35mm)
Screw (2x10mm)
Screw (2x10mm)
2Bushing (8X6mm)
Bushing (8X6mm)
8TP Screw (2.6x14mm)
TP Screw (2.6x14mm)
1.5mm
Secure the air retracts gear with typer screw.
Washer(3x6mm)
Washer(3x6mm)
8
6mm
2Wood dowel (6x30mm)
1Rib template (2mm ply)Rib template (2mm ply)
Rib template (2mm ply)
According to the rib template drill holes in one wing andepoxy wood dowel in them.
Secure the flap servo. Install the nylon control horn and connect the linkage.
Assemble the wheel and the gear door to the retract.Install the nylon control horn and connect the linkage.
12
1311
15
3
Accessory list for the coming installation steps.
14
90 mm
24 mm
2Wood dowel (6x50mm)
6mm
Main wing joiner1
Securely glue together. If coming off during flights, you 'lllose control of your airplane which leads to accidents!
B'B
C = C 'B = B '
Make sure to glue securely.If not properly glued, a failure in flight may occur.
Temporarily fasten down the main wing and check its correct position.
Securely glue together.If coming off during flights,you'll lose control of your airplane which leads to accidents!
C'C
6.2mm
Blind Nut
2
2Blind Nut (6mm)
Screw(6x50mm)
90 mm 25 mm
6mm
Epoxy the main wing together.
Drill holes at appropriate position in the wing for fetching out the servo line and air pipe.
Drill two holes to appropriate position in thewing and epoxy the wood dowel in it.
Assemble the main wing separately andbe sure with the right way.
Mount the main wing to the fuselage.
Drill two holes to relevant position in the fuselagefor installing the main wing.17
18
19
20
21
4
16
Fuel tank (550cc) 1
Linkage Stopper
Washer (2mm)
Washer (2mm)
Nut (2mm)
Set screw (3x4mm)
Washer (2mm)
Set screw (3x4mm)
1
1
1
1
Fuel supply line
Fuel spray lineAir pressure line
Set Screw (3x4mm)
Set Screw (2mm)
Rod (2x400mm)
Set Screw (2mm)
Washer (2mm)
Linkage Stopper1
1
1
1
1
4
4
Washer (4x8mm)4
Rod (2x400mm)
Blind Nut (4mm)
Screw (4x25mm)
Set Screw (3x4mm)
Assemble the servo and switch.
Mount the servo and switch in the fuselage.
Assembly of the fuel tank.
Mount the fuel tank into the fuselage.
Assemble the accelerator push rod to nose engine.
Assemble the accelerator push rod to nose engine.
44
45
46
47
48
9
43
Washer (4x8mm)Screw (4x25mm)
Washer (4x8mm)
Washer (4x8mm)
Screw (4x35mm)
Spring Washer (4mm)
Nut (4mm)
4mm
In case of 2-cycle & 4-cycle engine.
Ply (15x15x2mm) 2
Ply (15x15x2mm)
4Blind Nut (4mm)
5.2mm
Blind Nut
153mm
Fuel tank (550cc) 1
TP Screw (2.3x8mm) 51
Engine mount (68x105mm)
Linkage Stopper44
12
4
Washer(4x8mm)
Screw (4x35mm)
Spring Washer (4mm) Nut (4mm)
4Screw (4x25mm)
2
Plastic tube (2x400mm)
4Blind Nut (4mm)
2Ply (15x15x2mm)
Two nacelle bottom covers are supplied for optional assembly of door,which is decided by customers.Hardware package is not included.
TP Screw (2.3x12mm)
6TP Screw (2.3x12mm)
2
5mm
Assemble the engine.The front view when the engine install completion.
Drill four holes at the diameters as shown for engine mount.
The side view when the engine install completion.
Install the bottom cover.
39
40
41
42
8
38
Accessory list for the coming installation steps.
1
6Pin hinge(24x24mm)
Stab joiner (12x230mm)
B'B
A = A 'B = B '
Make sure to glue securely.If not properly glued, a failure in flight may occur.
Temporarily fasten down the main wing and check its correct position.
Securely glue together.If coming off during flights,you'll lose control of your airplane which leads to accidents!
A A '
4Matal douel (4x30mm)
1Rib template (3mm ply)
4mm
1Rib template (3mm ply)
A ccording to thr rib template drill holes to the tail of fuselage as below.
3Pin hinge(2.5x48mm)
4mm
4Wood dowel (4x30mm)
Drill two holes at the stabilizer root base via rib templateand epexy the wood dowel in them.
Securely glue together. If coming off during flights, you 'lllose control of your airplane which leads to accidents!
1Stab joiner (12x230mm)
11
Screw (2x10mm) Nut (2mm )
1Copper ball (2mm )
U-style wire
2mm
Metal arms
Screw (2x10mm)
Nut (2mm )Copper ball
Trim the shaded section
1U-style wire (150x3mm)
1U-style wire (150x3mm)
Assemble horizontal tail separately and be sure with the right way.
Assemble the stablilizers carefully to fuselage.
Set the U-style wire through the tail of fuselage as below.22
23
24
25
26
5
Accessory list for the coming installation steps.
3Pin hinge(2.5x48mm)
2.5mm
Make sure hinges are mounted in the same line.
1mm
Rudder
Tailing edge
Cut away the rubber tube whenthe epoxy glue dried.
Make sure they are inthe right position whileinstalling.
Keep some space about 1mm width between the tailing edge and the rudder.
Drill holes to appropriate position in the rudder and epoxythe ping hinges in them
Drill slots to appropriate position in the stabilizer .
2x12mm
Make sure hinges are mounted in the same line.
6Pin hinge(24x24mm)
Apply instant type CA glue to pin hinges and elevator.
Elevator
1mm
Tailing edge
Make sure they are inthe right position whileinstalling.
Keep some space with 1mm width between the tailing edge and elevator.
3mm
Glue the elevator to the stabilizer by CA and epoxy.
Securely glue together. If coming off during flights, you 'lllose control of your airplane which leads to accidents!
3mm
34mm103mm
103mm
28
27 30
31
29
6
32
2.5mm
Drill holes to the relevant position in the tailing edge and epoxy the rudder to them.
Note:rubber wheels oleo struts and retracts are optional.
Retracts strut
Nut (4mm)
1.5mm
4TP Screw (2.6x14mm)
TP Screw (2.6x14mm)
2Steel wire (0.5x1500mm)2Clevis 4TP Screw (2.6x14mm) 6TP Screw (2.3x12mm)
2Plastic tube(3x50mm)1Nut (4 mm )
1Wheel (75mm)
22
Copper joinerAluminum tube(3x6mm)
2Clevis22
Screw (2x10mm) Nut (2mm )
2
22
ClevisCopper joiner
Aluminum tube(3x6mm)
22
Screw (2x10mm) Nut (2mm )
2Washer(2x5mm)
Stee l w i re
Copper joinerAluminum tubeLock Nut (2mm )
Screw (2x10mm)
Ball joint
Washer(2x5mm)
2Nut (2mm )2Washer(2x5mm)
1Bushing (8X6mm)
Bushing (8X6mm)
Trim a small slot to appropriateposition in the whell shaft and fixing the shaft by set screw.
Assemble the wheel to the nose retract.
Install the nose retract .
Assemble the servo in the fuselage.
Install the servo of nose gear.
33
37
35
36
34
7
Accessory list for the coming installation steps.