service manuals lg tv plasma 50pm1ma 50pm1ma service manual
TRANSCRIPT
PLASMA MONITORSERVICE MANUAL
CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS : RF-052A
MODEL : 50PM1M/MA/MB50PM1M/MA/MB-TA
website:http://biz.LGservice.come-mail:http://www.LGEservice.com/techsup.html
- 2 -
CONTENTS
SAFETY PRECAUTIONS ....................................................................................3
DESCRIPTION OF CONTROLS ..........................................................................4
SPECIFICATIONS................................................................................................9
ADJUSTMENT INSTRUCTIONS .......................................................................11
TROUBLE SHOOTING GUIDE..........................................................................16
PRINTED CIRCUIT BOARD ..............................................................................25
BLOCK DIAGRAM.............................................................................................27
EXPLODED VIEW..............................................................................................30
EXPLODED VIEW PARTS LIST ........................................................................31
REPLACEMENT PARTS LIST...........................................................................32
SCHEMATIC DIAGRAM.........................................................................................
- 3 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by inthe Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual toprevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used duringthe servicing of a receiver whose chassis is not isolated fromthe AC power line. Use a transformer of adequate power ratingas this protects the technician from accidents resulting inpersonal injury from electrical shocks.
It will also protect the receiver and it's components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replaceit with the specified.
When replacing a high wattage resistor (Oxide Metal FilmResistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Due to high vacuum and large surface area of picture tube,extreme care should be used in handling the Picture Tube.Do not lift the Picture tube by it's Neck.
Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source,connect an electrical jumper across the two AC plug prongs.Place the AC switch in the on position, connect one lead ofohm-meter to the AC plug prongs tied together and touch otherohm-meter lead in turn to each exposed metallic parts such asantenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.
Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using ACvoltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat ACvoltage measurements for each exposed metallic part. Anyvoltage measured must not exceed 0.75 volt RMS which iscorresponds to 0.5mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.
Leakage Current Hot Check circuit
1.5 Kohm/10W
To Instrument’sexposed METALLIC PARTS
Good Earth Groundsuch as WATER PIPE,CONDUIT etc.
AC Volt-meter
IMPORTANT SAFETY NOTICE
0.15uF
POWERMUTE
INPUT MULTIMEDIA
ARC MENU
VOLOK
1 2 3
4 5 6
7
PSM SSM
8 9
0
VOL
SPLIT ZOOM SLEEP
REVEAL MODE
MIXSIZE
UPDATE TIMEQ.VIEW
HOLD INDEX
?
i
I/II
TEXT/
LIST/
MULTIMEDIAselects the Component, RGB or
HDMI modes.
POWERswitches the set on from standby oroff to standby.
ARC changes the picture format.
MENUdisplays on screen menus one by one.exits the current menu.memorizes menu changes.
SSMto select the sound appropriate toyour viewing programme character.
NUMBER buttons
SLEEPsets the sleep timer.
I/II (option)selects the language during dual lan-guage broadcast.selects the sound output.
TEXT/* (option)These buttons are used for teletext.For further details, see the ‘Teletext’section.COLOURED BUTTONS :These buttons are used for teletext.
LIST (option)displays the programme table.
INPUT
MUTEswitches the sound on or off.
DD / EESelects a menu option.
FF / GG (Volume Up/Down)Increases/decreases sound level.
Adjusts menu settings.OK
accepts your selection or displays thecurrent mode.
PSMadjusts the factory preset picture
according to the room.
SPLIT ZOOMenlarge the screen with regular
ration.
Q.VIEW (option)Returns to the previously viewed
programme.Note : This function works only when
Favourite prog. is set to Off .Otherwise each press of this button
will select a stored favorite programme.
- 4 -
DESCRIPTION OF CONTROLS
- 5 -
<Front Panel Controls>
42PM1MA/J series / 50PM1MA/J series
ON/OFF
1. Main Power Button
2. Remote Control Sensor
3. Power Standby IndicatorIlluminates red in standby mode, Illuminates green when theset is turned on
4. INPUT SELECT Button
5. MENUDisplays on screen menus one by one.Exits the current menu.Memorizes menu changes.
6. DD / EESelects a menu option.FF / GG (Volume Up/Down)Increases/decreases sound level.Adjusts menu settings.
1
4
5
6
3 2
- 6 -
<Back Panel>
AC INPUT
AUDIO INPUT RGB INPUT
RGB OUTPUT
RS-232C INPUT(CONTROL/SERVICE)
REMOTECONTROL
S-VIDEO
Y PB PR
VIDEO
R L
VARIABLE AUDIO OUT
AUDIOR L
EXTERNAL SPEAKER HDMI/DVI(VIDEO) INPUT
R L
AUDIO
R L
AUDIO
R L
AUDIO VIDEO
COMPONENT INPUT 2
COMPONENT INPUT 1
MONITOR OUPUT
A/V INPUT(MONO) (MONO)
Antenna
Connection to PC Connection to AV equipment
- 7 -
<Back Panel>
AC INPUT
AUDIO INPUT RGB INPUT
RGB OUTPUT
RS-232C INPUT(CONTROL/SERVICE)
REMOTECONTROL
Y PB PR
VIDEOS-VIDEO
R L
VARIABLE AUDIO OUT
AUDIOR L
EXTERNAL SPEAKER HDMI/DVI(VIDEO) INPUT
L R
VIDEO AUDIO
COMPONENT INPUT
AV3(MONO) AV1 AV2
AV1AV1
Antenna
RCA Type
Scart Type
4
AC INPUT
AUDIO INPUT RGB INPUT
RGB OUTPUT
RS-232C INPUT(CONTROL/SERVICE)
REMOTECONTROL
S-VIDEO
Y PB PR
VIDEO
R L
VARIABLE AUDIO OUT
AUDIOR L
EXTERNAL SPEAKER HDMI/DVI(VIDEO) INPUT
R L
AUDIO
R L
AUDIO
R L
AUDIO VIDEO
COMPONENT INPUT 2
COMPONENT INPUT 1
MONITOR OUPUT
A/V INPUT(MONO) (MONO)
Antenna
1 2 3 4 5
1. RS-232C INPUT(CONTROL/SERVICE) PORTConnect to the RS-232C port on a PC.
2. HDMI/DVI (VIDEO) / AUDIO INPUT / RGB INPUT SOCKETSConnect the monitor output socket of the PERSONAL COM-PUTER to this socket.Note: If you want to use RGB/DVI audio, we strongly recom-mend that you use the cable that has a core, or the EMI Filtercore along with separate cable.
RGB OUTPUT SOCKETYou can watch the RGB signal on another set, connect RGBOUTPUT to another monitor’s PC input port.
REMOTE CONTROL
VARIABLE AUDIO OUTPUT
3. EXTERNAL SPEAKER OUTPUT (8 ohm)Connect to optional external speaker(s).* For further information, refer to ‘Speaker & Speaker Stand’
manual.
4. COMPONENT / AUDIO INPUT SOCKETSS-VIDEO / AUDIO (L/MONO) INPUT SOCKETSVIDEO / AUDIO (L/MONO) INPUT SOCKETS
ANTENNA INPUT
EURO SCART SOCKETConnect the euro scart socket of the VCR to these sockets.Note: a. If you want to use the EURO scart cable, you have to usethe signal shielded Euro scart cable.b. If you want to use your external hi-fi stereo system, turn offthe internal speakers of the set.
5. POWER CORD SOCKETThis set operates on an AC power. The voltage is indicated onthe Specifications page. Never attempt to operate the set onDC power.
- 8 -
AS mark
LG TV
Owner’s Manual
1.5V1.5V
Alkaline batteriesPower Cord
POWERMUTE
INPUT MULTIMEDIA
ARC MENU
VOLOK
1 2 3
4 5 6
7
PSM SSM
8 9
0
VOL
SPLIT ZOOM SLEEP
REVEAL MODE
MIXSIZE
UPDATE TIMEQ.VIEW
HOLD INDEX
?
i
I/II
TEXT/
LIST/
Remote Control handset
- Optional extras can be changed or modified for quality improvement without any notification new optional extras can beadded.
- Contract your dealer for buying these items.
Optional Extras
Accessories
Tilt wall mounting bracket
404250 40 42 50
Video cables Audio cables
Ceiling mounting bracket
40
4250
42
40
Desktop stand
Speakers
SPECIFICATIONSNOTE : Specifications and others are subject to change without notice for improvement.
- 9 -
V Application RangeThis spec is applied to the PDP TV used RF-052A Chassis.
V Specification
Each part is tested as below without special appointment.1) Temperature : 25±5°C (77±9°F), CST : 40±52) Relative Humidity: 65±10%3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz)
* Standard Voltage of each product is marked by models.4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM.5) The receiver must be operated for about 20 minutes prior to the adjustment.
V Test Method1) Performance : LGE TV test method followed.2) Demanded other specification
Safety: IEC60065EMI : CISPR13
V General Specification
1. Module Specification
Remark
PDP
LGE SPEC
Maker : SONY/ LGIT/ Sanken
Specification
50 inch wide Color Display Module
16:9
PDP50X3,
RGB Closed Type
1) Temp : 0~40 deg
2) Humidity : 0~85%
1) Temp : -20~60 deg
2) Humidity : 0~85%
100-240V~, 50/60Hz
No
1
2
3
4
5
6
Item
Display Screen Device
Aspect Ratio
PDP Module
Operating Environment
Storage Environment
Input Voltage
2. Model Specification
- 10 -
Item
Market
Broadcasting system
Available Channel
Receiving system
Video Input (1EA)
Video Output(1EA)
S-Video Input(1EA)
Component Input(2EA)
RGB Input
RGB Output
HDMI Input(1EA)
Audio Input(5EA)
Audio Input(1EA)
Audio Output(3EA)
Audio Output(2EA)
Wired Control
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Specification
Non-EU
PAL B/G/I/D/K, NTSC
BAND PAL
VHF E2~E12
UHF E21~E69
CATV S1~S47
HYPER S1~S20
Upper Heterodyne
PAL, SECAM, NTSC
PAL, SECAM, NTSC
PAL, SECAM, NTSC
Y/Cb/Cr, Y/Pb/Pr
RGB-PC, RGB-DTV
RGB-PC, RGB-DTV
HDMI-PC, HDMI-DTV
PC Audio, Component(2EA),
AV(1EA), S-audio(1EA)
PC Audio
AV(1EA), External audio out(1EA),
Variable Audio out(1EA)
External audio out(1EA)
Variable Audio out(1EA)
Discrete IR
Remark
Except 42PM1MB, 50PM1MB, 42PM3MVB
Except 42PM1MB, 50PM1MB, 42PM3MVB
Except 42PM1MB, 50PM1MB, 42PM3MVB
42PM1M, 42PM1MA, 50PM1M, 50PM1MA
42PM3MV, 42PM3MVA
42PM1MB, 50PM1MB, 42PM3MVB
42PM1M, 42PM1MA, 50PM1M, 50PM1MA,
42PM3MV, 42PM3MVA
42PM1MB, 50PM1MB, 42PM3MVB
- 11 -
ADJUSTMENT INSTRUCTIONS
1. Application ObjectThese instructions is applied all of the PDP TV, RF-052AChassis.
2. Specification(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolationtransformer will help protect test instrument.
(2) Adjustment must be done in the correct order.(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity ifthere is no specific designation.
(4) The input voltage of the receiver must keep 100-220V,50/60Hz.
(5) The receiver must be operated for about 15 minutes priorto the adjustment.
O After RGB Full white HEAT-RUN Mode, the receiver mustbe operated prior to adjustment.
O Enter into HEAT-RUN MODE1) Press the POWER ON KEY on R/C for adjustment.2) OSD display and screen display 100% full White pattern.
[ Set is activated HEAT-RUN without signal generator inthis mode.
[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check PANEL.
Caution) If you turn on a still screen more than 20 minutes,(Especially digital pattern, cross hatch pattern) afterimage may be occur in the black level part of the screen.
3. Channel memory
3-1. Setting up the LGIDS1) Install the LGIDS. (idsinst.exe)2) After installation, restart your PC.3) Extract [files.zip] to folder [c:\LGIDS\files].4) Start LGIDS.
3-2. Channel memory Method 1) Select “PDP” and “Hurricane” on Model dialog. And check
your connection in Communication dialog. (If yourconnection is ‘NG’, then set your PORT(COM1,2,3,...)correctly.)
2) Connect RS-232C cable and turn on the power.(If your connection has completed, you can see “Ready”.)
[ If your set is not an end products but only a board, youhave to make your board to Stand-by state (LED_R). Andyou have to Download in Stand_by power state.
3) Select proper CH_memory file(*.nvm) for each model at[NVRAM Download] $ [Write Batch]Next, select proper binary file(*.bin) including the CHinformation for each model at [NVRAM File].
4) Click the [Download] button.It means the completion of the CH memory download if allitems show ‘OK’ and Status is changed by ‘PASS’ at thelower right corner of the window.
5) If you want to check whether the CH information ismemorized correctly or not, click the [Verify] button. And then compare NVRAM File(*.bin) with the CHinformation downloaded.
(Fig. 1)
(Fig. 2-1)
(Fig. 2-2)
- 12 -
4. POWER PCB Assy V oltageAdjustments (Va, Vs Voltage Adjustments)
4-1. Test Equipment : D.M.M. 1EA
4-2.Connection Diagram for Measuring: refer to fig.3
4-3. Adjustment Method[P/No 3501V00221A B/D]
(1) Va Adjustment1) After receiving 100% Full White Pattern, HEAT RUN.2) Connect + terminal of D.M.M to Va pin of P805, connect
- terminal to GND pin of P805.3) After turning RV601, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top.(Deviation; ±0.5V)
(2) Vs Adjustment1) Connect + terminal of D.M.M to Vs pin of P805, connect
– terminal to GND pin of P805.2) After turning RV401, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top.(Deviation; ±0.5V)
5. EDID (The Extended DisplayIdentification Data)/ DDC (DisplayData Channel) download
5-1. Required T est Equipment1) Adjusting PC with S/W for writing EDID Data.(S/W : EDID
TESTER Ver.2.5)2) A Jig for EDID Download3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub
15Pin cable, DVI to HDMI cable
5-2. Setting of device
5-3. Preparation for Adjustment1) As above Fig. 5, Connect the Set, EDID Download Jig, PC
& Cable.2) Turn on the PC & EDID Download Jig. And Execute the
S/W : EDID TESTER Ver,2.53) Set up S/W option
Repeat Number : 5Device Address : A0PageByte : 8
4) Power on the Set
5-4. Sequence of Adjustment
(1) DDC data of Analog-RGB1) Init the data
2) Load the EDID data.(Open File)[Analog-RGB : MF056A_RGB.ANA][digital(HDMI) : MF056A_DMI.DVI]
3) Set the S/W as below.4) Push the “Write Data & Verify”button. And confirm “Yes”.5) If the writing is finished, you will see the “OK” message.
Each PCB assembly must be checked by check JIG set.(Because power PCB Assembly damages to PDP Module,especially be careful)
Va ADJRV601
P806
P805
P807
Va
GNDNCVS
DMM
+ - P804
P801 P802
Vs ADJRV401
P803
(Fig. 3) Connection diagram of power adjustment for measuring
(Fig. 4) Connection Diagram of DDC download
- 13 -
6. Auto A V(CVBS) Color Balance
6-1. Requirement- This AV color balance adjustment should be performedbefore white Balance Adjustment
6-2. Required Equipment1) Remote controller for adjustment2) AV Pattern Generator
: 802F Pattern Generator, Master(MSPG-925FA), etc(Which has PAL Composite Video format output withstandard(1.0 Vpp) Vertical 100% Color Bar Pattern as Fig6)
6-3. Method of Auto A V(CVBS) Color Balance1) Input the PAL Composite Video (Fig6. 100% Color Bar
Pattern) into video input.(RCA : AV1, SCART : AV3 Input, PAL : 50Hz, NTSC : 60Hz)
2) Set the PSM to Standard mode in Picture menu.3) Press INSTAR key on R/C for adjustment.4) Press the G(Vol. +) key operate to set, then it becomes
automatically.5) Auto-RGB OK means completed adjustment.
7. Adjustment of White Balance
7-1. Required Equipment1) Remote controller for adjustment2) Color Analyzer (CA-100 or same product)3) Auto W/B adjustment instrument(only for Auto adjustment)4) AV Pattern Generator
7-2. Connecting diagram of equipment formeasuring (For Auto Adjustment)
W Auto adjustment Map(RS-232C)
7-3. Adjustment of White Balance(For Manual adjustment)
O Operate the zero-calibration of the CA-100, then sticksensor to PDP module surface when you adjust.
O For manual adjustment, it is also possible by the followingsequence.
1) Select white pattern of heat-run mode by pressing poweron key on remote control for adjustment then operate heatrun more than 15 minutes.
2) As below Fig.8, Supply 216Level (85 IRE) full screenpattern to Video input.(RCA : AV1, SCART, AV3 Input, PAL : 50Hz, NTSC: 60Hz)
3) Press the TV/AV KEY on R/C for converting input mode.4) Set the PSM to Standard mode in Picture menu.5) Enter the White Balance adjustment mode by pressing the
INSTART key twice(White Balance) on R/C.
(Fig. 6) Auto AV(CVBS) Color Balance Test Pattern
216 Level (85 IRE)
Type
Baud Rate
115200
Index
R Gain
G Gain
B Gain
R Offset
G Offset
B Offset
Data bit
8
Cmd1 Cmd2
j a
j b
j c
j d
j e
j f
Stop bit
1
Parity
NONE
RF-052A/B/C
ProtocolSetting
Data Min Value
00(00)
00(00)
00(00)
00(00)
00(00)
00(00)
Max Value
255(FF)
255(FF)
255(FF)
255(FF)
255(FF)
255(FF)
(Fig. 7) Connection Diagram of Auto W/B Adjustment
MSPG-2100 /MSTG- 5200
216 Level (85 IRE)
COLORANALYZERTYPE ; CA-100
CVBSsignalinput
RS-232C Serial Communication
(Fig.5) EDID DATA
- 14 -
6) Stick sensor to center of the screen and select each items(Red/Green/Blue Gain and offset) using D / E(CH +/-) keyon R/C.
7) Adjust Only High Light with R Gain/ B Gain using F / G(VOL+/-) key on R/C.
8) Adjust it until color coordination becomes as below.(Initially, R/G/B gain and R/G/B offset values are fixedRed Gain : 82, Green Gain : 80, Blue Gain : 86Red Offset : 7D, Green Offset : 7E, Blue Offset : 80)(High Light G Gain : 7A // Low Light R Offset : 7F, G Offset7E, B Offset 80 is Fixed)Bright : High Light : 80 ± 20cdColor-Coordinate : High Light : X : 0.285 ± 0.003
Y : 0.295 ± 0.003Color Temperature : 9,300°K ± 500°K
9) When adjustment is completed, Exit adjustment mode usingEXIT key on R/C
8. Auto Component Color Balance[Requirement]It is very import to use correct adjustment pattern like fig.9
V Within the pattern, color sequence should be aligned: W-Y-C-G-M-R-BLUE-BLACK
(If color sequence is reversed(Black -> ... > White), reversethe pattern with REV key, when using Master patterngenerator like MSPG-925)
V If Minimum Black Level and/or Maximum White Level is not correct, Do select 100% Color Bar Pattern.
8-1. Required T est Equipment1) Remote controller for adjustment2) 802F Pattern Generator
(Which has 720p Ypbpr output & PC 1024x768 60Hz withStandard(0.7Vpp) Vertical 100% Color Bar Pattern as Fig.9)
8-2. Method of auto component color balance1) Input the Component 720p 100% Color Bar signal into
Component1 or Component2.2) Set the PSM to Standard mode in Picture menu.3) Press INSTART key on R/C for adjustment.4) Press the G(Vol. +) key operate To set, then it becomes
automatically.5) Auto-RGB OK means complete adjustment
9. Auto RGB Color Balance[Requirement]It is very import to use correct adjustment pattern like fig.9
V Within the pattern, color sequence should be aligned: W-Y-C-G-M-R-BLUE-BLACK(If color sequence is reversed(Black -> ... > White), reversethe pattern with REV key, when using Master patterngenerator like MSPG-925)
V If Minimum Black Level and/or Maximum White Level is notcorrect, Do select 100% Color Bar Pattern.
9-1. Required T est Equipment1) Remote controller for adjustment2) 802F Pattern Generator
(Which has VGA 60Hz PC Format output with standard(0.7Vpp) Vertical 16 Gray Scale pattern as Fig.10)
9-2. Method of Auto RGB Color Balance1) Input the PC 1024x768 60Hz 100%Color bar into RGB.2) Set the PSM to Standard mode in Picture menu.3) Press ADJ key on R/C for adjustment.4) Press the G(Vol. +) key operate To set, then it becomes
automatically.5) Auto-RGB OK means completed adjustment.
(Fig. 10) Auto RGB Color Balance Test Pattern
(Fig. 9) Auto Component Color Balance Test Pattern
(Fig. 8) Pattern for Adjustment of White Balance
216 Level (85 IRE)
10. Default value in adjustment mode
10-1. Auto Color Balance (Component/RGB)
10-2. White Balance
- 15 -
(Fig. 12) Default Value on OSD
(Fig. 11) Default Value on OSD
Auto Color Balance(HEX)
Auto-RGB G To SetSource CortezRed Offset1 22Green Offset1 24Blue Offset1 23Red Offset2 45Green Offset2 43Blue Offset2 37Red Gain 014Green Gain 031Blue Gain 011Reset G To Set
White Balance(Hex)
Red Gain 82Red Offset 80Green Gain 86Green Offset 7DBlue Gain 7EBlue Offset 80Reset G To Set
- 16 -
TROUBLE SHOOTING GUIDE
1. Power Board
1-1. The whole flowchart which it follows in voltage output state
Start check
Manufacture enterprisemeaning of a passage
1. Check the Power Offcondition.
Doesn't the screen whole come
out?
Is it identical with Power Off
condition?
Yes
Yes
No
No
No
No
No
2. Check the Interfacesignal condition.
Is the Interface signal operated?
Yes
3. Check the St-by 5Vsignal circuit.
Doesn't the low pressure output
come out?
Doesn't the St-by 5V signal
come out?
Yes
Yes
No
4. Check the 5V Monitorsignal circuit.
Doesn't the 5V Monitor signal
come out?
Yes
7. Check the VSC Vs-ONsignal
Doesn't the high tension output
come out?
Doesn't the VSC signal Vs-ON
come out?
Yes
Yes
Doeshigh tension
output voltage Dropoccur?
When theY B/D Module
input connector isremoved, does output
voltage dropoccur?
When theY, Z B/D Module
input connector is remove,does Power Board high tension
output voltage Dropoccur?
Yes No No
9. Check the PowerBoard Output high
tension circuit
Yes
10. Check the Z B/DModule output circuit
Yes
When theZ B/D Module
input connector isremoved, does output
voltage Drop occurs?
11. Check the Y B/DModule output circuit
Yes
No
8. Check the Vs, Vavoltage output circuit.
Doesn't the Vs, Va voltage output
come out?
Yes
No
No
5. Check the VSC RL-ONsignal.
Doesn't the VSC signal RL-ON
come out?
Yes
6. Check the VSC lowpressure output
Doesn't the VSC low pressureoutput come out?
Yes
- 17 -
1-2. Sony Power Board Structure
1 2 3
T502: Vs Trans
T702: Va Trans
T101: St-by Trans
T103: Low Voltage Trans
- 18 -
1-3. Sanken, LGIT Power Board Structure
1 2 3
T221: Vs Trans
T271: Va Trans
T121: St-by Trans
T201: Low Voltage Trans
- 19 -
2. No Power
(1) SymptomØ Does’t minute discharge at module. Ø Non does not come in into the front LED.
(2) Check following
Is plug in power cord? Plug in power cord.
Yes
No
Is the Line Filter and PowerBoard Cable connected?
Connect the Cable.
Yes
No
Is the Fuse(F101) onPower Board normal?
Replace the Fuse.
Yes
No
Is the Power Board and 7P ofVSC Board Cable connected?
Connect the Cable.
Yes
No
After the cable connect is removedto Power Board(except the CN101connection cable), the AC voltagemarking is authorized on manual.When ST-BY 5V is not operated,replace Power Board.
- 20 -
3. Protect Mode
(1) SymptomØ After once shining, it does not discharge minutely
from moduleØ The Rely falls(The sound is audible “click”) Ø It is converted with the color where the front LED
is red from green.
(2) Check following
Is the Power Boardnormal ?
Replace PowerBoard.
Is output the normality Low/Highvoltage except Stand-by 5V?
Yes
No No
Is the each connectornormal?
Replace theconnector.
ReplaceY-Board.
After connecting well each connector,the normality it operates?
Yes
No No
Is the Ctrl Boardnormal?
ReplaceX-Board.
Is the output voltage normal afterremove P1, 2, 4, 9, 10 connector of
Ctrl-B/D?
Yes
No Yes
Is the Y-Boardnormal?
Is the output voltagenormal after removeP5, P6 connector of
Y-B/D?
Is the Fuse(FS2) on Y-B/D normal?(In case of open is replace)
Yes
No Yes Yes
ReplaceZ-Board.
Is the Z-Boardnormal?
Is the output voltagenormal after removeP1 connector of Z-
B/D?
Is the Fuse (FS1, FS2) on Z-B/Dnormal? (In case of open is replace)
Yes
No Yes
Is the X- Boardnormal?
Is the output voltage normal afterremove P1, 2, 3, 4, 5 connector of
X-B/D?
After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace Left X-B/D
Yes
No Yes
Is the VSC Board normal?
Is the output voltage normal afterremove P1001, P1100?
After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.
After remove P1001, 1100 normaloperation: Replace VSC Board
Yes
No
Is the COF of X, Y, Znormal ?
No
Yes
Yes
- 21 -
4. No Raster
(1) SymptomØ Does’t minute discharge at module. Ø It maintains the condition where the front LED is green.
(2) Check following
Is the Power Boardnormal?
Replace thePower Board.
Is output the normality Low/Highvoltage except Stand-by 5V?
Yes
No No
Is the each connectornormal?
Replace theconnector.
ReplaceY-Board.
After connecting well each connector,the normality it operates?
Yes
No No
Is the Ctrl Board normal?
ReplaceX-Board.
Is the output voltage normal afterremove P1, 2, 4, 9, 10 connector of
Ctrl-B/D?
Yes
No Yes
Is the Y-Boardnormal?
Is the output voltagenormal after removeP5, P6 connector of
Y-B/D?
Is the Fuse(FS2) normal on Y-B/D?(In case of open is replace)
Yes
No Yes Yes
ReplaceZ-Board.
Is the Z- Board normal?
Is normal the outputvoltage after remove
P1 connector of Z-B/D?
Is the Fuse(FS1, FS2) normal onZ-B/D? (In case of open is replace)
Yes
No Yes
Is the X- Board normal?
Is the output voltage normal afterremove P1, 2, 3, 4, 5 connector of
X-B/D?
After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace the Left X-B/D
Yes
No Yes
Is the VSC Board normal?
Is the output voltage normal afterremove P1001, P1100?
After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.
After remove P1001, P1100 normaloperation: Replace the VSC Board
Yes
No
Is the COF of X, Y, Znormal?
No
Yes
Yes
- 22 -
5. In case of occurring strange screen into specific mode
5-1. In case the OSD does not displayed
(1) SymptomØ LED is greenØ The minute discharged continuously becomes accomplished from module
(2) Check following
Is the LVDS cablenormal ?
Is the VSC Boardnormal?
Is the LVDS cableconnected well?
Cable inserts well.Yes
No
No
Yes
Does the FIL8532 IC(IC800) Operates ?
Replace FIL8532IC(IC800).
No
Is the Ctrl Board ofModule normal?
Replace Ctrl B/D.No
No
YesReplace VSC B/D
Replace the cable.Yes
- 23 -
5-2. In case of does’t display the screen into specific mode
(1) SymptomØ The screen does not become the display from specific input mode
(RF, AV, Component, RGB, DVI).
(2) Check followingØ Check the all input mode should become normality display.Ø Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become
normality display from the PIP mode or DW mode. (Re-Check it Swap)
(3) In case of becomes unusual display from RF mode
(4) In the case of becomes unusual display from RF, AV mode
(5) In the case of becomes unusual display from Component, RGB mode
(6) In the case of becomes unusual display from HDMI mode
Is the Tuner normal?
Is the CXA2069Qnormal?
Is the Tuner Cableconnected well?
Cable inserts well.Yes
No
No
Yes
Is the FIL8532normal?
Replace the Tuner
No
Is the Input voltage, IIC Communicationand CVBS output normal?
Yes
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace the IC
No
Is the CXA2069Qnormal?
Yes
Is the FIL8532normal?
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is the FIL8532normal?
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is the Sil9011normal?
Yes
Is the FIL8532normal?
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
- 24 -
6. In case of no sound
(1) SymptomØ LED is greenØ Screen display but sound is not output
(2) Check following
Is the SPK cablenormal?
Is the SPK cableconnected well?
Cable inserts well.
No
No
Replace IC400
No
Replace IC401
No
Replace SPK cableYes
Yes
Is the RF/ AV/Component/ RGB/
HDMI sound normal?
No Does IC400Operates ?
Does IC401Operates ?
Replace IC402
No
Does IC402Operates ?
Replace VSC B/D
Yes Yes
PRINTED CIRCUIT BOARD
- 25 -
MAIN(TOP)
MAIN(BOTTOM)
- 26 -
RCA(TOP) RCA(BOTTOM) CONTROL
POWER SWITCH(TOP) POWER SWITCH(BOTTOM)
- 27 -
BLOCK DIAGRAMC
able
RC
A B
lock
Dia
gram
- 28 -
Sca
rt B
lock
Dia
gram
Cab
le
MEMO
- 29 -
- 30 -
EXPLODED VIEW
305
300
200
301
303
530310
400
580501
540
541
520
600
601
101
103
102
220
230
304
302
208
201
207
206
205
204
203
202
- 31 -
101 5900V12003C FAN, G1225S12B2-FS DONGYANG DC AXIAL 12V 120MM 1250 PRM 3P 280MM HOUSING
102 4980V01018A SUPPORTER, FAN EGI LEFT PDP DN-50PY10
103 4980V01017A SUPPORTER, FAN EGI RIGHT PDP DN-50PY10
200 6348Q-C043M PDP, 50” 1365*768 PDP50X30010.AKLGG
6348Q-C049H PDP, 50” 1365*768 PDP50X30010.ADDDB
6348Q-C049N PDP Module, 50” 1365*768 PDP50X30010.AKDDG
201 6871QCH059A PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 50X3 CTRL LGPCM1224
202 6871QDH088A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 50X3 YDRV TOP
203 6871QDH089A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 50X3 YDRV BOTTOM
204 6871QLH049A PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 50X3 X-LEFT(TCP)
205 6871QXH030A PWB(PCB) ASSEMBLY,DISPLAY XRCT ASSY HAND INSERT _ 50X3 X-CENTER (TCP)
206 6871QRH057A PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 50X3 X-RIGHT (TCP)
207 6871QYH039A PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT FOR 50X3
208 6871QZH044A PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT FOR 50X3
220 4980900191A SUPPORTER, ASSY ADC MODULE ASSY RIGHT 50PM1M
4980900191B SUPPORTER, ASSY ADC SKD MODULE ASSY RIGHT 50PM1M
230 4980900192A SUPPORTER, ASSY ADC MODULE ASSY LEFT 50PM1M
4980900192B SUPPORTER, ASSY ADC SKD MODULE ASSY LEFT 50PM1M
300 3091V00724A CABINET ASSEMBLY, 50PM10 RF04GA NON
3091V00724B CABINET ASSEMBLY, 50PM10 RF04GA C/SKD
301 4980V00C24A SUPPORTER, FILTER EGI TOP ASSY
4980V00C24C SUPPORTER, FILTER AL MZ-50PM10 TOP SKD
302 4980V00C25A SUPPORTER, FILTER EGI BOT ASSY
4980V00C25C SUPPORTER, FILTER AL MZ-50PM10 BOT SKD
303 4980V00C27A SUPPORTER, FILTER EGI SIDE L ASSY
4980V00C27C SUPPORTER, FILTER AL MZ-50PM10 SIDE L SKD
304 4980V00C26A SUPPORTER, FILTER EGI SIDE R ASSY
4980V00C26B SUPPORTER, FILTER AL MZ-50PM10 SIDE R ASSY C/SKD
305 5230V00017B FILTER(MECH), 50PX5D-UB LGM50-03 MITSUI 50” CLASS B GLASS FILTER
310 5020V01004C BUTTON, CONTROL 42PM10 6KEY
400 3809V00502A BACK COVER ASSEMBLY, 50PM10 NO WARNING
3809V00502C BACK COVER ASSEMBLY, 50PM10 NON MZ-50PM10 SKD NO WARNING
3809V00502F Cover Assembly, MT-50PM10 NON AUSTRALIA
3809V00502L Cover Assembly, 50PM1M-TA RF052A 50” HONGKONG WITH 412-737A
501 3301900007A PLATE ASSEMBLY, AV PLATE ASSY 3300900001 3300900002 50PM10 X3
520 6871VMMF41A PWB(PCB) ASSEMBLY,MAIN RF-052A H2.MNT. MT-50PM15
530 6871VSMS70A PWB(PCB) ASSEMBLY,SUB CONT RF052A H2 50PM1M
540 6871VSME92A PWB(PCB) ASSEMBLY,SUB PSW RF043A MAILBU
541 5020900001A/ B BUTTON, POWER 50PM10/20 PC-ABS 1KEY X3 MODULE
580 6709V00001A POWER SUPPLY ASSEMBLY, 50INCH AF05GA 480W 1H259W SANKEN 50 INCH LOW END PSU
600 6871VSMAFFA PWB(PCB) ASSEMBLY,SUB RF052A H2 MONITOR RCA ATTACHABLE 1 TUNER
6871VSMANNA PCB Assembly,Sub SUB M.I RF052A 60PZ9M-TA . H2 MONITOR RCA ATTACHABLE NO TUNER
601 4980V00C30K/ P/ S SUPPORTER, AV INTERFACE EGI 50PM1MA-TA/50PM1MB-TA
EXPLODED VIEW PARTS LIST
No. Part No. Descriptions
MIC39100 MICREL 3P SOT223 R/TP
BA033FP-E2 ROHM 3P-SOP,TO252-3 R/TP 3.3V
KA7809R, FAIRCHILD 2P D-PAK, R/TP IC
SC156515M-1.8TR SEMTECH 5P/TO-263-5
BA033FP-E2 ROHM 3P-SOP,TO252-3 R/TP 3.3V
BA033FP-E2 ROHM 3P-SOP,TO252-3 R/TP 3.3V
BA033FP-E2 ROHM 3P-SOP,TO252-3 R/TP 3.3V
MIC39100 MICREL 3P SOT223 R/TP
SC156515M-1.8TR SEMTECH 5P/TO-263-5
KIA78R05F KEC 5PIN DPAK R/TP 1A,5V
SC156515M-1.8TR SEMTECH 5P/TO-263-5
MIC39100 MICREL 3P SOT223 R/TP
SII9011CLU(PB FREE) SILICON IMAGE 128P
AT24C02N-10SI-2.7 ATMEL 8P SOIC R/TP
KIA78R05F KEC 5PIN DPAK R/TP 1A,5V
MC34063ADR2G ON SEMI SO-8P R/TP
CXA2069Q QFP64 BK I2C BUS AV S/W
LA7217M MFP14 TP SYNC SEPARATOR
MSP4410K MICRONAS 80P/PQFP
NSP-2100A,LF NEOFIDELITY TQFP 64P
TAS5122DCARG4,LF 56P/TSSOP R/TP
74HC14D 14SOP TP SHITTER TRIGGER
AT24C02N-10SI-2.7 ATMEL 8P SOIC
74HC14D 14SOP TP SHITTER TRIGGER
OPA3692IDBQ BUR BROWN 16PIN SSOP
ICL3232CBNZ INTERSIL 16P/SOP R/TP
KIA78R09F KEC 5PIN DPAK R/TP 1A,9V
KIA78R09F KEC 5PIN DPAK R/TP 1A,9V
LM75CIMX-3 8P/SOP R/TP
FLI8532BD-LF GENESIS 416P/PBGA
24LC256T-I/SMG(PB FREE)
K4D261638F-LC50,LF TSOPII 66P
K4D261638F-LC50,LF TSOPII 66P
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
KRA102S R/TP KEC SOT23 CHIP TR
CHIP 2SC3875S(ALY) BK KEC
REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION
Q1200
Q1401
Q1402
Q201
Q202
Q203
Q204
Q205
Q207
Q300
Q301
Q302
Q303
Q304
Q305
Q400
Q401
Q402
Q403
Q404
Q405
Q406
Q407
Q408
D1005
D1006
D1007
D1008
D1009
D1010
D1012
D1013
D1100
D1105
D1106
D1107
D1109
D1110
D1200
D1201
D1500
D500
D501
D502
D504
D505
D506
D600
ZD300
ZD301
ZD400
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR150400BA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR102008AA
0TR387500AA
0TR387500AA
0TR102008AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD200009AF
0DD200009AF
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD184009AA
0DS113379BA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DR050008AA
0DR050008AA
0DR050008AA
0DD100009AM
0DR050008AA
0DR050008AA
0DZRM00248A
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SA1504S(ASY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
KRA102S R/TP KEC SOT23 CHIP TR
CHIP 2SC3875S(ALY) BK KEC
CHIP 2SC3875S(ALY) BK KEC
KRA102S R/TP KEC SOT23 CHIP TR
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
RU2M V(1) TP R-TMD 400V 1.1A 20A 0.4US
RU2M V(1) TP R-TMD 400V 1.1A 20A 0.4US
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS184 TP KEC - 85V - 300MA
1SS133 T-72 TP ROHM KOREA DO34 90V
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
EU1ZV(1) TP E/EO-TMD 200V
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
RLZ8.2B-TE11 R/TP LLDS(LL-34) 500MW
LOCA. NO PART NO DESCRIPTION
IC1000
IC1001
IC1002
IC1003
IC1004
IC1005
IC1100
IC1101
IC1102
IC1103
IC1104
IC1105
IC1200
IC1201
IC1502
IC202
IC300
IC301
IC400
IC401
IC402
IC407
IC500
IC502
IC509
IC600
IC601
IC602
IC603
IC800
IC802
IC901
IC902
IC1202
IC1203
IC200
IC201
IC503
IC504
Q100
Q1000
Q1001
Q1002
Q1003
Q1004
Q101
Q101
Q102
Q102
0IPRPML001A
0IMCRRH001A
0IMCRFA010A
0IPMG00027A
0IMCRRH001A
0IMCRRH001A
0IMCRRH001A
0IPRPML001A
0IPMG00027A
0IPMGKE030A
0IPMG00027A
0IPRPML001A
0IPRPS5005A
0IMMRAL014B
0IPMGKE030A
0IPMGON013B
0ISO206900A
0ISA721700C
0IMCRMN028B
0ILNR00015A
0IMCRTI028C
0IPH741400E
0IMMRAL014B
0IPH741400E
0IPRPBB005A
0IPRP00009A
0IPMGKE032A
0IPMGKE032A
0IPRPNS054A
0IMCR02005A
0IMMR00024A
0IMMR00002A
0IMMR00002A
0TR830009BA
0TR830009BA
0TR830009BA
0TR830009BA
0TR830009BA
0TR830009BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR102008AA
0TR387500AA
IC
TRANSISTOR
- 32 -
DIODE
- 33 -
LOCA. NO PART NO DESCRIPTION
ZD600
C1000
C1005
C1007
C1009
C1010
C1019
C103
C103
C1030
C1043
C1046
C1047
C1050
C1051
C1064
C1065
C1066
C1067
C1068
C1069
C1071
C1073
C108
C1082
C1083
C1084
C1085
C1087
C1098
C1099
C1102
C1105
C1107
C1108
C1110
C1115
C1116
C1117
C1118
C1119
C1120
C1126
C113
C1136
C1137
C1138
C114
C1148
C1156
0DR050008AA
0CE477SF6DC
0CE477SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE477SF6DC
0CE476SF6DC
0CE477SF6DC
0CE477SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE477SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE477SF6DC
0CE477DJ618
0CE477SF6DC
0CE227VF6DC
0CE477SF6DC
0CE477DJ618
0CE227VF6DC
0CE477SF6DC
0CE106SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE106SF6DC
0CE476SF6DC
0CE476SF6DC
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF STD 35V 20% FL TP 5
470UF MVG 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
470UF STD 35V 20% FL TP 5
220UF MV 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
LOCA. NO PART NO DESCRIPTION
C1159
C1160
C1162
C1166
C1185
C1186
C1187
C1194
C1199
C1200
C1201
C1225
C1230
C1231
C1245
C1247
C1304
C1306
C1311
C1312
C1313
C1315
C1316
C1317
C1318
C1481
C1482
C1502
C1507
C1514
C1515
C1516
C1832
C1833
C1834
C204
C210
C211
C214
C215
C215
C221
C238
C241
C300
C304
C305
C307
C315
C318
C319
C320
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE477SF6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CK105DF64A
0CK105DF64A
0CE106SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE475SK6DC
0CE475SK6DC
0CE477SF6DC
0CE477SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE477SF6DC
0CE475SK6DC
0CE477SF6DC
0CE106SF6DC
0CE105SK6DC
0CE475SK6DC
0CE477SF6DC
0CE107SF6DC
0CE476SK6D8
0CE107SF6DC
0CE226SF6DC
0CE107SF6DC
0CE476SF6DC
0CK225DFK4A
0CK225DFK4A
0CK225DFK4A
0CK225DFK4A
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
1UF 2012 16V 20% F(Y5V) R/TP
1UF 2012 16V 20% F(Y5V) R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
4.7UF MVG 50V 20% SMD R/TP
4.7UF MVG 50V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
4.7UF MVG 50V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
1UF MVG 50V 20% SMD R/TP
4.7UF MVG 50V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
47UF MVG,MC 50V 20% SMD TAPPING
100UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
CAPACITOR
- 34 -
LOCA. NO PART NO DESCRIPTION
C335
C337
C342
C368
C370
C371
C402
C403
C407
C413
C418
C419
C421
C425
C444
C451
C456
C457
C462
C463
C464
C465
C477
C480
C481
C482
C483
C484
C485
C495
C527
C545
C546
C547
C548
C549
C550
C553
C555
C557
C559
C610
C614
C615
C620
C621
C622
C832
C833
C834
C835
C836
0CE476SF6DC
0CE105SK6DC
0CE105SK6DC
0CK225DFK4A
0CK225DFK4A
0CK225DFK4A
0CE476SF6DC
0CE106SF6DC
0CE107SF6DC
0CE335VK6DC
0CE107SF6DC
0CE107SF6DC
0CK105DF64A
0CE226SF6DC
0CE107SF6DC
0CK105DF64A
0CK105DF64A
0CE335VK6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SK6DC
0CF4741L438
0CE108DJ618
0CE475SK6DC
0CE475SK6DC
0CF4741L438
0CF4741L438
0CF4741L438
0CE108DJ618
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE477VF6DC
0CE477VF6DC
0CE477VF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
47UF MVG 16V 20% SMD R/TP
1UF MVG 50V 20% SMD R/TP
1UF MVG 50V 20% SMD R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
47UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
3.3UF MV 50V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
1UF 2012 16V 20% F(Y5V) R/TP
22UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
1UF 2012 16V 20% F(Y5V) R/TP
1UF 2012 16V 20% F(Y5V) R/TP
3.3UF MV 50V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 50V 20% SMD R/TP
0.47UF D 63V 5% TP 5 M/PE NI
1000UF STD 35V 20% FL TP 5
4.7UF MVG 50V 20% SMD R/TP
4.7UF MVG 50V 20% SMD R/TP
0.47UF D 63V 5% TP 5 M/PE NI
0.47UF D 63V 5% TP 5 M/PE NI
0.47UF D 63V 5% TP 5 M/PE NI
1000UF STD 35V 20% FL TP 5
47UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
470UF MV 16V 20% R/TP(SMD) SMD
470UF MV 16V 20% R/TP(SMD) SMD
470UF MV 16V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
LOCA. NO PART NO DESCRIPTION
C837
C838
C839
C840
C851
C853
C884
C896
C901
C904
C905
C930
C946
C947
C952
L1000
L1101
L1102
L1103
L1104
L1124
L409
L410
L411
L412
C1
C2
C3
C4
C5
C6
C7
C8
JK401
JK503
JK601
P1001
P100A
P100B
P101
P1100
P400
P401
P600
P601
P800
P801
P802
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0032A
6140VB0032A
6140VB0032A
6140VB0032A
366-036B
6631V00045K
6631V12047J
6631V25032E
6631V25083G
6631V39015E
6631V39016E
6631V39021H
385-173B
6630G70021A
6630VGA004B
366-921F
6630VL01280
6630VL01380
6602T12002M
366-921J
366-932C
366-932B
366-932B
366-932B
6602T12006M
6630VM01604
6630VM01702
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
DBF-1015A 15.5UH 10PIE DIGITAL AUDIO
DBF-1015A 15.5UH 10PIE DIGITAL AUDIO
DBF-1015A 15.5UH 10PIE DIGITAL AUDIO
DBF-1015A 15.5UH 10PIE DIGITAL AUDIO
STAPLE
10P 2.5MM 550MM H-H UL1007AWG24
13P 1.25MM 500MM H-H UL1061AWG28
3P 2.5MM 300MM H-H UL1007 AWG26
7P 2.5MM 400MM H-H UL1007 AWG24
4P 3.96MM 300MM H-H UL1007AWG18
10P 3.96MM 300MM H-H UL1007AWG18
4P 3.96MM 450MM H-H UL1672AWG18
VER TYPE . 4 . 2LINE 4P A+B
DV11251-PV8-PF FOXCONN 30P 2.54MM
69107-0921 MOLEX 9P 2.77MM
GIL-G-07P LGC 7PIN 2.54MM STICK
2-557100-1 AMP 80P 2.54MM PLUG
2-557101-1 AMP 80P 2.54MM RECEPTACLE
53261-1390 MOLEX 13P 1.25MM R/A SMD
GIL-G-10P LGC 10PIN 2.54MM STICK
IL-G-04P LGC 2.5MM S/T STICK
IL-G-03P LGC 2.5MM S/T STICK
IL-G-03P LGC 2.5MM S/T STICK
IL-G-03P LGC 2.5MM S/T STICK
53398-1390 MOLEX 13P 1.25MM S/T SMD
YW396 4P 3.96MM ANGLE, MN-60PZ12
YW396 2P 3.96MM (ANGLE TYPE)
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
COIL
CONNECTOR
- 35 -
LOCA. NO PART NO DESCRIPTION
P803
AR1200
AR1201
AR1202
AR1203
AR1204
AR1205
R1112
R1113
R230
R618
R801
R802
D1003
D1101
D1102
D1103
D1104
LD101
SW102
SW103
SW105
SW106
SW107
SW108
SW800
SW800
IC403
IC404
IC406
L100
L1004
L1005
L1006
L1007
L1008
L1009
L101
L1010
L1011
L1012
L1013
L1014
L1015
6602T12007D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RS0472K607
0RS0472K607
0RD0331H609
0RD0152H609
0RKZVTA001L
0RKZVTA001L
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL200000CA
140-313B
140-313B
140-313B
140-313B
140-313B
140-313B
6600VM2006A
6600VR1004A
6200VJS001B
6200VJS001B
6200VJS001A
6200JB8010L
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200JB8010L
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
GT121-31P-TD LGC 31P 1.25MM DUAL S/T
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
47 OHM 2 W 5.00% TA62
47 OHM 2 W 5.00% TA62
3.3 OHM 1/2 W 5.00% TA52
15 OHM 1/2 W 5.00% TA52
1.0M OHM 1/2 W 5% TA52 UL PILKOR
1.0M OHM 1/2 W 5% TA52 UL PILKOR
SAM2333 TP GREEN:10MCD, RED:6MCD
SAM2333 TP GREEN:10MCD, RED:6MCD
SAM2333 TP GREEN:10MCD, RED:6MCD
SAM2333 TP GREEN:10MCD, RED:6MCD
SAM2333 TP GREEN:10MCD, RED:6MCD
SAM5670(DL-2LRG) BK Y-GREEN -
2LEAD 160G(TA) 5V 0.001A HORIZONTAL .G
2LEAD 160G(TA) 5V 0.001A HORIZONTAL .G
2LEAD 160G(TA) 5V 0.001A HORIZONTAL .G
2LEAD 160G(TA) 5V 0.001A HORIZONTAL .G
2LEAD 160G(TA) 5V 0.001A HORIZONTAL .G
2LEAD 160G(TA) 5V 0.001A HORIZONTAL .G
SDDF3PATP011 250V 4A HORIZONTAL .G
SKHMPW 5P J-ALPS .V .A HORIZONTAL .G
ZJYS51R5-2PL(T) TDK R/TP 50VOLT 2A
ZJYS51R5-2PL(T) TDK R/TP 50VOLT 2A
ZJY51R5-4P TDK DIP DC 50VOLT 2A
MLB-201209-1000L-N2 R/TP 1000OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-201209-1000L-N2 R/TP 1000OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
LOCA. NO PART NO DESCRIPTION
L1016
L1017
L1018
L1019
L102
L1020
L1021
L1022
L1023
L1024
L103
L104
L1106
L1107
L1108
L111
L112
L1125
L1126
L1127
L113
L1131
L114
L115
L116
L119
L120
L1204
L1205
L1206
L1207
L1208
L1209
L121
L122
L137
L1501
L1502
L1503
L202
L203
L204
L300
L301
L400
L401
L402
L403
L406
L407
L408
L500
6200J000013
6200J000013
6200J000013
6200J000013
6200JB8010L
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200JB8010L
6200JB8010L
6200J000013
6200J000013
6200J000013
6210VC0005A
6210VC0005A
6200J000013
6200J000013
6200J000013
6210VC0005A
6200J000013
6210VC0005A
6210VC0005A
6210VC0005A
6200JB8010L
6200JB8010L
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200JB8010L
6200JB8010L
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-201209-1000L-N2 R/TP 1000OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-201209-1000L-N2 R/TP 1000OHM
MLB-201209-1000L-N2 R/TP 1000OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
BK2125 HS 750 2X1.25X0.85MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
BK2125 HS 750 2X1.25X0.85MM R/TP
MLB-321611-0500P-N2 R/TP 500 OHM
BK2125 HS 750 2X1.25X0.85MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
MLB-201209-1000L-N2 R/TP 1000OHM
MLB-201209-1000L-N2 R/TP 1000OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-201209-1000L-N2 R/TP 1000OHM
MLB-201209-1000L-N2 R/TP 1000OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
SWITCH
FILTER & CRYSTAL
LED
RESISTOR
- 36 -
LOCA. NO PART NO DESCRIPTION
L501
L502
L503
L506
L514
L515
L516
L517
L604
L901
L902
X1200
X300
X400
X800
JK101
JK102
JK103
JK104
JK105
JK1200
JK400
JK502
A1
A1
A2
A3
A3
CA1
CA2
F801
IC900
PA101
TU201
6210VC0005A
6200JB8010L
6200JB8010L
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6212AB2845A
166-E02F
156-A02M
6212AB2844A
6612VJH020C
6612VJH019C
6612VJH020B
380-363G
6612JH003CA
6612B00015A
6612JH003CA
6612F00006F
3828VA0564E
38289U0516A
6710T00017M
64109EP003A
6410VBH003H
68509A0002A
6850J00005C
0FS1002B53K
6927V1298AH
6712000002B
6700MF0012C
BK2125 HS 750 2X1.25X0.85MM R/TP
MLB-201209-1000L-N2 R/TP 1000OHM
MLB-201209-1000L-N2 R/TP 1000OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
MLB-321611-0500P-N2 R/TP 500 OHM
RESONATOR,CRYSTAL ABLS-27.000MHZ
RESONATOR,CERAMIC CSBLA500KECZF09-B0
RESONATOR,CRYSTAL HC49U 18.432MHZ
RESONATOR,CRYSTAL ABLS-19.6608MHZ
PPJ122C A/V 6P(COMPONENT)+SHIELD+GOLD
PPJ121-22 A/V 4P FOR EMI WITH SWITCH RED
PPJ122B A/V 6P+SHIELD+GOLD
6046B-01S PARKELEC H=8.0 WITH S/W,SHIELD
PPJ137A AUDIO L-MONO JACK
DC1R019NDA JAE 1.0MM,19PIN,HDMI JACK
PPJ137A AUDIO L-MONO JACK
KJA-PH-3-0064 KSD 3.5PHI 14P DUALJACK
MANUAL, USER B/D AR/FR/EN 138L TX 114%
MANUAL, USER EN 017M/N-TX
REMOTE CONTROLLER, RF052A NON-EU
POWER CORD, SP-023+IS-14 1870MM
POWER CORD, 003D-G/SOURCING 2800MM
CABLE,COAXIAL 150MM KCA-NS-0-0053 KSD
CABLE,DVI LVDS UL20276 AWG30 600MM
FUSE, 10000MA 250 V 5.2X20
SOFT WARE, 3.11V 59B6 1366X768
REMOTE CONTROLLER RECEIVER,KSM-603SM12E-1
TUNER, TAFM-W103P LGIT MULTI FS
LOCA. NO PART NO DESCRIPTION
ACCESSORIES
MISCELLANEOUS
JACK
Apr., 2006Printed in KoreaP/NO : 3828VD0223T