series 001 intallation guide - bento...appliance cases 8.1 sink 8.2 dishwasher 8.3 microwave cabinet...
TRANSCRIPT
![Page 1: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/1.jpg)
SERIES 001INTALLATION GUIDE
![Page 2: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/2.jpg)
2OVERVIEWS
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINTRODUCTION
DISCLAIMERDue to potential differences in wall construction, floor finish, hardware selection, and overall quality of Lattice System installation, Bento cannot specify loading restrictions for the Series 001 System.
Series 001 cabinets are designed to support reasonable loads over the course of their lifetime. Avoid overloading cabinets, only using them for their intended purpose and distributing weight evenly. They are not intended for use outside of their specified purpose.
Similarly, we do not recommend standing or sitting on any part of the System, other than parts specifically designed by Bento for that purpose. Bento is not responsible for the condition or strength of the wall or ensuring the Lattice System is mounted correctly. Similarly, Bento cannot be held liable for any failure to follow the specified guidelines.
Please refer to the BentoBuild Contractor’s Guide and Lattice Installation Guide for details of assembly.
Note:After delivery, store cabinets in a space with 40 to 50 percent relative humidity. Humidity above 70 percent or below 20 percent is likely to cause warping or damage to finishes. If stored in a garage, basement or other space where humidity and temperature differ from the room where the cabinets will be installed, allow 1-2 days for cabinets to acclimate to their final environment before installation.
![Page 3: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/3.jpg)
1
2
43
HANGING CABINETS1.1 Instructions
1.2 Kitchen Installation
ADJUSTING CABINETSInstructions
FITTING TOE KICKSInstructions
FITTING COUNTERTOPSInstructions
SEAMING THE COUNTERTOPSInstructions
FITTING THE BACKSPLASHInstructions
FITTING SPECIALTY ITEMSInstalling T-Nuts into Pegboards
05
07
08
12
17
19
20
23
567
![Page 4: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/4.jpg)
APPLIANCE CASES8.1 Sink
8.2 Dishwasher
8.3 Microwave Cabinet
8.4 Refrigerator
8.5 Oven
8.6 Cooktop
8.7 Hood
25
29
32
33
35
37
38
8
![Page 5: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/5.jpg)
5S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EHANGING CABINETS INSTRUCTIONS
HANGING CABINETS
Step 1BentoBuild modules should be installed from bottom to top.
1
1
22
1
3
1
1.1 Instructions
![Page 6: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/6.jpg)
6S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EHANGING CABINETS INSTRUCTIONS
Step 2Line up cleats at the back of module with slots in struts. Drop each cleat into corresponding slots until cleat rests fully in each slot. Ensure cleats are fully engaged in struts before continuing to the next step.
321
![Page 7: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/7.jpg)
7S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EHANGING CABINETS KITCHEN INSTALLATION
Roughed-in, finished wall
Install Lattice System Identify plumbing and electrical connections
Install base modules and appliances
Run utilities through backsplash and install
Install remaining modules
1
4
2
5
3
6
1.2 Kitchen Installation
![Page 8: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/8.jpg)
8S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSADJUSTING CABINETS
ADJUSTING CABINETS
Step 1
Drill out blind holes on cabinet interiors. Drill into scrap wood blocking to avoid chip out.
2
Step 2Insert shims as necessary to create an 1/8” gap between modules.
Instructions
![Page 9: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/9.jpg)
9S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSADJUSTING CABINETS
Step 3Use connector bolts to attach adjacent modules.
![Page 10: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/10.jpg)
10S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSADJUSTING CABINETS
Step 4Adjust Euro hinges and flip-up hinges as necessary.
EURO HINGES
FLIP-UP HINGES
Up/Down
Depth
Left/Right
![Page 11: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/11.jpg)
11S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSADJUSTING CABINETS
Step 5Adjust drawer slides as necessary.
![Page 12: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/12.jpg)
12S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSFITTING TOE KICKS
FITTING TOE KICKS3Step 1Screw cabinet feet into corresponding base plates.
Step 2Level cabinet feet to the ground.
Instructions
![Page 13: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/13.jpg)
13S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSFITTING TOE KICKS
Step 3Align clip to toe kick adapters with cabinet feet.
Step 4Use a rubber mallet to hammer adapters into groove of toe kick.
![Page 14: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/14.jpg)
14S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSFITTING TOE KICKS
Step 5Slide clips sideways over adapters so that they interlock.
Step 6Attach toe-kick-clips to feet
![Page 15: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/15.jpg)
15S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSFITTING TOE KICKS
Step 7At corner conditions only:
7A.
7B.
Where toe kick clips intersect, flip one around to attach both clips to a single foot.
Use a P-connector to join perpendicular toe kicks and tighten with provided torque wrench.
A P-connector is a two-part connector. Both parts are joined by a cam-lock.
![Page 16: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/16.jpg)
16S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSFITTING TOE KICKS
Step 8Remove protective plastic film from front of toe kick.
![Page 17: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/17.jpg)
17S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSFITTING COUNTERTOPS
FITTING COUNTER TOPS4Step 1Make sure countertop aligns with base cabinets below. Clamp countertop to base cabinets if necessary.
Instructions
![Page 18: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/18.jpg)
18S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSFITTING COUNTERTOPS
Step 2Use a fender washer and ¼” -20 screws (½” long) to connect countertop to base cabinets where needed.
Countertop (underside)
Cabinet (underside)
Pocketed thru-hole
Fender washer
Bolt
Weld nut
![Page 19: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/19.jpg)
19S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSSEAMING THE COUNTERTOPS
SEAMING THE COUNTERTOPS5Step 1For seaming countertops, refer to manufacturer's instructions.
Note:For Corian only, sequence numbers of both Corian slabs should differ by no more than 50 to ensure adequate color match.
Instructions
![Page 20: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/20.jpg)
20S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSFITTING THE BACKSPLASH
FITTING THE BACKSPLASH6Step 1Thread armored electrical cables and flexible plumbing through holes in backsplash.
Step 2Line up backsplash with corresponding struts and place shims underneath backsplash to prevent cleats from engaging.
Instructions
![Page 21: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/21.jpg)
21S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSFITTING THE BACKSPLASH
Step 3Apply silicone beading along the back edge of countertop underneath backsplash.
Step 4Remove shims and add silicone beading to gaps.
Step 5Engage backsplash cleats with corresponding struts.
![Page 22: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/22.jpg)
22S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EINSTRUCTIONSFITTING THE BACKSPLASH
Step 7Wipe surface and clean as necessary.
Step 8Wait for silicone beading to dry and fully cure before installing electrical or plumbing.
Step 6Spray glass cleaner over the silicone beading.
![Page 23: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/23.jpg)
23S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EPEGBOARDFITTING SPECIALITY ITEMS
Installing T-Nuts into Pegboards
FITTING SPECIALITY ITEMS7Step 1Some pegboard accessories do not require any setup, and can simply be pushed into place.
![Page 24: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/24.jpg)
24S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EPEGBOARDFITTING SPECIALITY ITEMS
Step 4Hammer T-nuts provided into the backside of pegboard.
Step 5After pegboard has been installed on the Lattice System, screw accessories into selected locations.
Step 3Insert T-nut into the backside of pegboard at selected location.
Step 2For screw-in pegboard accessories, select location of accessory before mounting pegboard to Lattice System.
![Page 25: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/25.jpg)
25S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EAPPLIANCE CASES SINK
8.1 Sink
APPLIANCE CASES8Step 1For ADA sink cabinets, install cabinet-specific feet and inset toe kick using connectors supplied with each part
Step 2Apply clear silicone beading around the interior recessed edge of sink cabinet.
![Page 26: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/26.jpg)
26S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EAPPLIANCE CASES SINK
Step 5Mount and seam countertop. Reference Sections 4 and 5.
Step 4Add sink strainer cup to sink basin.
Step 3Place sink basin into sink cabinet opening.
![Page 27: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/27.jpg)
27S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EAPPLIANCE CASES SINK
Step 6Before moving forward with next steps, ensure that all drains and water supplies have been connected correctly to sink basin and faucet.
Note: If assembly includes a dishwasher, run dishwasher drain and water supply through hole in side of sink case.
Step 7For ADA sink cabinets after plumbing hookup:
7A
Insert knee panel in at an angle to sink case until it slides into bottom of case.
7B
Hook knee panel into corresponding pegs in lower portion of sink cabinet.
![Page 28: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/28.jpg)
28S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EAPPLIANCE CASES SINK
7C 7D
7E
Rotate knee panel upwards until clips engage with corresponding receiving clips in sink cabinet.
Align holes in EZ Kick Panel with pilot holes at back of cabinet doors and fasten panels to doors using provided hardware.
Fasten toe kick panels to EZ Kick Panels.
Step 7 con.
![Page 29: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/29.jpg)
29S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EAPPLIANCE CASES DISHWASHER
1A
1B
ADD LEVEL
Step 1a Step 1b Step 1c Step 2 Step 4 Step 3 Step 1 Step 1
ADD LEVEL
Step 1a Step 1b Step 1c Step 2 Step 4 Step 3 Step 1 Step 1
Step 1Install top panel:
If dishwasher is next to a refrigerator or sink, the cases will have blind holes on the inside to use in next step. Drill out these holes with scrap wood blocking behind to avoid chip out.
Align brackets of sub-top with holes created in refrigerator cabinet and fasten brackets using hardware provided.
8.2 Dishwasher
ADD LEVEL
Step 1a Step 1b Step 1c Step 2 Step 4 Step 3 Step 1 Step 1
ADD LEVEL
Step 1a Step 1b Step 1c Step 2 Step 4 Step 3 Step 1 Step 1
![Page 30: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/30.jpg)
30S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EAPPLIANCE CASES DISHWASHER
ADD LEVEL
Step 1a Step 1b Step 1c Step 2 Step 4 Step 3 Step 1 Step 1
Using a bubble level, align top surfaces of both dishwasher sub-top and adjacent base cabinet. Tighten bracket.
1C
Step 2Install front panel, if applicable. Follow instructions provided by appliance manufacturer for doing so.
Step 1 continued
Non-faced Dishwasher Faced Dishwasher
ADD LEVEL
Step 1a Step 1b Step 1c Step 2 Step 4 Step 3 Step 1 Step 1
ADD LEVEL
Step 1a Step 1b Step 1c Step 2 Step 4 Step 3 Step 1 Step 1
![Page 31: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/31.jpg)
31S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EAPPLIANCE CASES DISHWASHER
Step 6Verify there is enough clearance between door and toe kick for door to open fully.
Step 5Adjust leveling feet to ensure dishwasher rests below sub-top and is perpendicular to countertop.
Step 4Connect dishwasher to electrical supply.
Step 3Before moving forward with next steps, ensure dishwasher is connected to water supply and drain.
ADD LEVEL
Step 1a Step 1b Step 1c Step 2 Step 4 Step 3 Step 1 Step 1
ADD LEVEL
Step 1a Step 1b Step 1c Step 2 Step 4 Step 3 Step 1 Step 1
ADD LEVEL
Step 1a Step 1b Step 1c Step 2 Step 4 Step 3 Step 1 Step 1
ADD LEVEL
Step 1a Step 1b Step 1c Step 2 Step 4 Step 3 Step 1 Step 1
![Page 32: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/32.jpg)
32S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EAPPLIANCE CASES MICROWAVE
Step 1Pass electrical cable through opening in the back of microwave cabinet and plug into outlet.
Step 2Insert microwave into cabinet until feet engage in corresponding pockets.
Step 3Attach false front panel using integrated Keku clips.
*Click*
*Click*
*Click*
*Click*
*Click*
*Click*
8.3 Microwave Cabinet
![Page 33: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/33.jpg)
33S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EAPPLIANCE CASES REFRIGERATOR
Step 1Pass electrical cable through opening in the back of refrigerator cabinet and plug into outlet.
Step 2Position refrigerator inside cabinet.
8.4 Refrigerator
![Page 34: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/34.jpg)
34S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EAPPLIANCE CASES REFRIGERATOR
Step 3Follow manufacturer instructions to install door panels and complete assembly.
Note: For 24” refrigerators, adjust front panels to leave a 1/16” inset between edge of case and refrigerator door. Leave ⅛” gap between refrigerator and freezer door.
![Page 35: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/35.jpg)
35S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EAPPLIANCE CASES OVEN
Step 1Leave enough space for electrician to perform electrical hookup through open back of oven cabinet.
Step 3Follow manufacturer instructions to complete installation.
Step 2Once electrical connection is complete, insert oven into cabinet.
8.5 Oven
![Page 36: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/36.jpg)
36S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EAPPLIANCE CASES COOKTOP
Step 1Leave enough space for the electrician to perform electrical hookup through open back of cooktop cabinet.
Step 3Follow manufacturer instructions to complete installation.
Note:Install cooktop after countertop installation.
Step 2Once the electrical connection is complete, insert cooktop into countertop opening.
8.6 Cooktop
![Page 37: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/37.jpg)
37S
ER
IES
00
1 IN
STA
LLATIO
N G
UID
EAPPLIANCE CASES HOOD
Step 1Refer to manufacturer’s instructions for installation.
8.7 Hood
![Page 38: SERIES 001 INTALLATION GUIDE - Bento...APPLIANCE CASES 8.1 Sink 8.2 Dishwasher 8.3 Microwave Cabinet 8.4 Refrigerator 8.5 Oven 8.6 Cooktop 8.7 Hood 25 29 32 33 35 37 38 8](https://reader034.vdocuments.mx/reader034/viewer/2022042412/5f2bf3b07e302e4c50200d85/html5/thumbnails/38.jpg)
BentoBuild254 36th Street Floor 6, Suite C663Brooklyn, NY 11232
o +1 718.260.8200BentoBuild.com