SEPTEMBER 2011

ROKKER™ SERIES 4-CHANNEL FAIRING SPEAKER AMPLIFIER•The world’s most powerful 4-channel speaker amplifier for your Harley® Bagger audio system

•Full-range Class G amplifier features 125W RMS per channel X4 channels (500W total) driven continuous into a 2 ohm load at 14.4vdc and 70watts RMS continuous X4 channels into a 4 ohm load

•Amplifier mounts to the top of the custom-made stainless steel bracket system, which has the slots in the bottom section to properly relocate two of the Harley CB, MP3 or XM sat radio modules (if installed)

•Kit includes custom-made plug-n-play wiring harnesses with top-quality heavy gauge power/ground wires to be used in conjunction with the fused battery connection

•Also includes all necessary mounting hardware and complete installation/operation instructions•Amplifier measures 105/8” L x 5” W (at widest point) x 15/8” T

PART # DESCRIPTION SUG. RETAIL4401-0110 For 11 FLTRU $739.95

PART # DESCRIPTION SUG. RETAIL4401-0111 For 06-11 FLHX $739.95

PART # DESCRIPTION SUG. RETAIL4401-0112 For 06-11 FLTR/FLTRX $739.95

4401-0110

4401-0111

4401-0110 4401-0111

PART # DESCRIPTION SUG. RETAIL4405-0241 For 06-11 FLHX, FLHTC, FLHTCU, FLHR w/ the factory Harley fairing lowers $449.95

71/4” ROKKER™ SERIES FAIRING LOWERS SPEAKER KIT•Largest diameter round speakers that can be installed into the Harley® lower fairing shells with cone volume and mass comparable to a 6” x 9” speaker

•High-power 3-way ROKKER series speaker set has been designed specifically for the Harley StreetGlide, Ultra, or RoadGlide custom with the factory Harley lower faring shells installed

•2 ohms impedance and 170+ watts max power for the ultimate in raw audio power

•Waterproof injection-molded polycarbonate woofer cone•High-flux strength but lite-weight dual-donut Neodymium magnet•High-efficiency vented voice-coil for improved cooling when operating at high volume levels for extended periods

•Custom designed grillwork with high-output titanium-colored tweeter and mid-range drivers•Specially-tuned speaker-mounted passive crossover network for improved fidelity and frequency response•Top-quality lower fairing housing inserts molded specifically to fit the Harley lower fairing shells, to hold the J&M ROKKER series 71/4” speaker and custom grille with mounted high-output tweeter and mid-range

•High-impact quality molded speaker inserts are textured in a matte finish and can be painted to match the color of your Bagger•Will perform extremely well when used with a medium to high-powered accessory amplifier

2

AKRAPOVICA combination of the fi nest materials, state-of-the-art facilities and a hands-on approach by modern craftsmen with a passion for perfection come together in exhausts that are second-to-none in the world today. Akrapovic is the pinnacle of WORLD CLASS exhaust function and style. These striking exhausts are designed to provide riders with the ultimate level of performance that Akropovic calls “PURE POWER.” Here a combination of premium materials along with rigorous research and testing leads to the optimum exhaust fl ow for American V-Twins in a Euro-infl uenced style that is second to none. Akropovic exhausts also sound like no others. Just the right notes at the right times. Deep, resonant sound – the sound of Pure Power. And, sound that can be easily adjusted with optional components, including a Valve System for the Slip-On Muffl ers that lets riders change the sound level with a simple switch – even on the fl y. State-of-the-art facilities along with the highest levels of technology, materials, R&D and testing come together with passion and expertise to bring H-D owners a true World Class exhaust.

OPEN LINE 2-INTO-1 SYSTEMS•Un-matched European craftsmanship, outstanding performance, design, and of course the unmistakable deep resonant sound of Akrapovic all come together in these 2-into-1 systems

•Highest quality materials are used throughout, including Austenitic (“surgical grade”) stainless steel along with show-quality chrome plating or Silicone-based black powder coating

•Systems feature Akrapovic’s in-house designed and tested, high-performance silencer insert design for incredible power and famous sound – not old-school baffling

•Systems include header, removable silencer insert, heat shields and complete installation instructions

PART # DESCRIPTION SUG. RETAILFOR 06-11 FXST/FLST, 06-11 FLHT/FLHX/FLHR/FLTR MODELS1800-1325 Chrome $799.951800-1326 Black 799.95

OPEN LINE 2-INTO-1 SYSTEMS

together with passion and expertise to bring H-D owners a true World Class exhaust.

1800-13251800-1326

OPEN LINE 2-INTO-2 SYSTEMS•Un-matched European craftsmanship, outstanding performance, design, and of course the unmistakable deep resonant sound of Akrapovic all come together here in these 2-into-2 systems

•Highest quality materials are used throughout, including Austenitic (“surgical grade”) stainless steel along with show-quality chrome plating or Silicone-based black powder coating

•Systems feature Akrapovic’s in-house designed and tested, high-performance silencer insert design for incredible power and famous sound – not old-school baffling

•Systems include removable silencer inserts, heat shields and complete installation instructions

PART # DESCRIPTION SUG. RETAILFOR 06-11 FXD/FXDWG MODELS1800-1327 Chrome $799.95

PART # DESCRIPTION SUG. RETAILFOR 06-11 XL MODELS1800-1328 Chrome $749.95

PART # DESCRIPTION SUG. RETAILFOR 06-11 XL MODELS (CONT)1800-1329 Black $749.95

complete installation instructions

OPEN LINE 2-INTO-2 SYSTEMS•Un-matched European craftsmanship, outstanding performance, design, and of course the unmistakable deep resonant sound of Akrapovic all come

1800-13271800-1329

3

PART # DESCRIPTION SUG. RETAIL1861-0733 For mufflers PART #s 1801-0528, 1801-0529 $449.951861-0734 For mufflers PART #1801-0530 449.951861-0735 For mufflers PART #1801-0531 449.951861-0736 For mufflers PART #s 1801-0532, 1801-0533 449.951861-0737 For mufflers PART #1801-0534 449.951861-0738 For mufflers PART #1801-0535 449.95

OPTIONAL SOUND VALVE SYSTEMS FOR SLIP-ON MUFFLERS•The perfect complement to Akropovic’s Slip-On Muffler line allows riders to easily adjust for the sound level they want without ever leaving the bike, or getting their hands dirty

•World Class design and function uses investment cast stainless steel housings and high-temperature graphite bearings throughout

•Valve systems are cable-actuated through a hand control that is mounted on-bike where owner can reach it

•At every setting there is still the unmistakable, deeply resonant sound of Akrapovic

•Sold in pairs

OPTIONAL SOUND VALVE OPTIONAL SOUND VALVE

1861-0733

PART # DESCRIPTION SUG. RETAIL1861-0729 Black 1” x 50’ $64.951861-0730 Tan 1” x 50’ 59.95

HIGH-TEMPERATURE EXHAUST WRAP KITS•Wraps will increase power and reduce radiated exhaust heat•Kits includes 50-ft., 1-in. wide top-quality high-temperature wrap and four stainless-steel tie wraps for that finishing touch

•Wraps can withstand up to 2,000°•Available in black or tan•Replacement 4-pack exhaust wrap clamps are also available (PART #1861-0320)

1861-0729

1861-0730

PART # DESCRIPTION SUG. RETAILFOR 07-11 FLSTF/FLSTFB, 07 FXSTD MODELS1801-0534 Chrome $1,149.95FOR 07-10 FXST/B/C, 07-11 FLSTC, 08-11 FXCW/C MODELS1801-0535 Chrome 1,149.95FOR 06-11 FXD/FXDWG MODELS (EXCEPT 08-11 FXDF, 10-11 FXDWG)1801-0531 Chrome 1,049.95FOR 06-11 FXDF/10-11FXDWG MODELS1801-0530 Chrome 1,049.95

PART # DESCRIPTION SUG. RETAILFOR 06-11 FLHT/FLHX/FLHR/FLTR MODELS (EXCEPT 10 FLHX/FLTRX)1801-0528 Chrome w/ chrome tips $1,149.951801-0529 Chrome w/ black tips 1,149.95FOR 06-11 XL MODELS1801-0532 Chrome 1,049.951801-0533 Black 1,049.95

SLIP-ON MUFFLERS•Just like the full systems, these are loaded with an exceptional array of Akropovic features

•Un-matched European craftsmanship, outstanding performance, design, and of course the unmistakable deep resonant sound of Akrapovic; here with an Optional Sound Valve System that can even be adjusted on-the-fly

•Highest quality materials are used throughout, including Austenitic (“surgical grade”) stainless steel along with show-quality chrome plating and Silicone-based black powder coating as listed

•Optional Sound Valve Systems are available separately•Dresser muffler bodies with end cap measure 20” L (29” overall length with subheader pipe installed) and are 41/2” W x 31/2” T at polygonal exit that tapers to 31/2” round inlet end

•Includes mufflers, subheaders with heat shields, clamps and complete installation instructions•Sold in pairs

1801-0529

1801-0530

1801-0531

1801-0530

1801-0533

1801-0534 1801-05311801-05341801-0534

1801-0535

4

ROAD RAGE II MEGA POWER SYSTEMS•Designed specifically to address the needs of tuned motors built for high horsepower applications

•Features 2-into-1 equal-length 13/4”-17/8” stepped headpipes•Megaphone muffler housing with 4” polished or black billet end cap with contrasting machined flutes

•Include full-coverage heat shields•Includes O2 sensor bung plugs for non-sensor applications

•Include removeable baffle•Made in the U.S.A.

PART # DESCRIPTION SUG. RETAILFOR 07-11 V-ROD MODELS1800-1317 Chrome, long meg w/ heat shields $699.951800-1318 Black, short w/ heat shields 739.95

ROAD RAGE II B1 POWER SYSTEMS•Designed specifically to address the needs of tuned motors built for high horsepower applications

•Uses a unique extended inner collector maximizing performance

•Features 2-into-1 equal-length stepped headpipes; systems for Dyna feature 2-step headers, 13/4” to 13/8”; systems for V-Rod feature 3-step headers, 13/4” to 17/8” to 2”

•4” straight-style performance muffler body with 21/2” x 161/2” baffle and billet end cap with contrasting machined flutes

•Include full-coverage heat shields•Oxygen sensor port plugs also included for non-sensor applications•Made in the U.S.A.

PART # DESCRIPTION SUG. RETAILFOR 07-11 VRSCAW, VRSCDX, VRSCX, 09-11 VRSCF1800-1315 Chrome w/ black billet end cap w/ machined

contrasting and chrome heat shields $699.95

PART # DESCRIPTION SUG. RETAILFOR 07-11 VRSCAW, VRSCDX, VRSCX, 09-11 VRSCF (CONT)1800-1316 Black w/ black billet end cap w/ machined

contrasting and black heat shields $739.95

PART # DESCRIPTIONSUG.

RETAILFOR VANCE & HINES 3.5” MUFFLERS1802-0183 Clean Cut, Contrast Cut™ $99.951802-0184 Clean Cut, chrome 99.951802-0185 Slash, Contrast Cut™ 99.951802-0186 Slash, chrome 99.951802-0187 Sweep, Contrast Cut™ 99.951802-0188 Sweep, chrome 99.95

PART # DESCRIPTIONSUG.

RETAILFOR VANCE & HINES 3.5” MUFFLERS (CONT)1802-0189 Tech 10, Contrast Cut™ $99.951802-0190 Tech 10, chrome 99.95FOR VANCE & HINES 4” MUFFLERS1802-0191 Clean Cut, Contrast Cut™ 99.951802-0192 Clean Cut, chrome 99.951802-0193 Slash, Contrast Cut™ 99.95

PART # DESCRIPTIONSUG.

RETAILFOR VANCE & HINES 4” MUFFLERS (CONT)1802-0194 Slash, chrome $99.951802-0195 Sweep, Contrast Cut™ 99.951802-0196 Sweep, chrome 99.951802-0197 Tech 10, Contrast Cut™ 99.951802-0198 Tech 10, chrome 99.95

ELITE EXHAUST END CAPS•CNC machined billet aluminum construction •Available in chrome and Contrast Cut™•Contrast Cut™ starts with a polished end cap that has been black anodized then re-cut to open up the design

•Sold each•Made in the U.S.A.

SUG.

Clean Cut Contrast CutClean Cut

Clean Cut Chrome

Contrast CutClean Cut

Slash Contrast CutSlash Slash

SlashChrome

Contrast CutSlashChrome

Sweep Contrast CutSweep Sweep

Sweep ChromeSweep

Tech 10 Contrast CutTech 10

Tech 10 Chrome

BASSANI XHAUSTLook. You don’t just have to take Darryl Bassani’s word on it that his exhausts make more power than anyone else’s – check it out for yourself. Pick-up any bike (or car) magazine with Bassani included in an exhaust comparo-test and see who comes out on top! Because whether it’s Detroit’s latest road burner or Milwaukee Iron’s fi nest, Bassani Xhaust’s winning performance sends the competition packing. Check out “The Sound of Power” today.Milwaukee Iron’s fi nest, Bassani Xhaust’s winning performance sends the Milwaukee Iron’s fi nest, Bassani Xhaust’s winning performance sends the

1800-1318

1800-1315

DESCRIPTION SUG. RETAIL

1800-1316

1802-0195

PREDATOR 2-UP SEATS•Solar-reflective leather in the seating area and automotive-grade vinyl on the sides; patented process reduces surface temperature by as much as 25°F for a cooler seat, higher durability and longer life over conventional leather or vinyl

•Molded polyurethane foam for maximum comfort and styling•3/16” ABS thermoformed seat base for a perfect fit•Rubber bumpers and fully carpeted bottom to protect paint•Fit with all Drag and most H-D sissy bars•1” lower than stock (unless noted)•Include all mounting hardware•Made in the U.S.A.

NOTE: 94-96 FLHR seats will fit also fit 89-93 FLHT models if hand rail is removed and a lower dash extension PART #2202-0070 is used.

5

PART # DESCRIPTION SUG. RETAILFOR 94-96 FLHR MODELS (31” L X 101/2” W)0801-0614 Smooth $309.950801-0615 Flame stitch 319.95

0801-0614 0801-0615

PREDATOR 2-UP SEATS•Solar-reflective leather in the seating area and automotive-grade vinyl on the sides; patented process reduces surface temperature by as much as 25°F for a cooler seat, higher durability and longer life over conventional leather or vinyl

•Molded polyurethane foam for maximum comfort and styling•3/16” ABS thermoformed seat base for a perfect fit•Rubber bumpers and fully carpeted bottom to protect paint•Fit with all Drag and most H-D sissy bars•Include all mounting hardware•Lower rider 3/4” compared to stock seat unless noted•Made in the U.S.A.

PART # DESCRIPTION SUG. RETAILFOR 84-99 FXST, FLST MODELS (29” L X 101/2” W FRONT X 63/4” W REAR)0802-0624 Smooth $304.950802-0625 Flame stitch 309.95

DESCRIPTION SUG. RETAIL

0802-0624 0802-0625

SOLO SEATS WITH BACKREST CAPABILITY•Solar-reflective leather in the seating area and automotive-grade vinyl on the sides; patented process reduces surface temperature by as much as 25°F for a cooler seat, higher durability and longer life over conventional leather or vinyl

•Flexible urethane foam for maximum comfort•3/16” ABS thermoformed seat base with carpeted bottom and rubber bumpers to protect paint

•Lower rider 11/2” from stock seat•Include two polished stainless steel mounting nuts and a leather fender bib for a cleaner installation

•Optional EZ GLIDE I™ backrest (PART #0822-0135) features a detent bar with multiple detents on lower portion for adjustability up and down within the seat and chrome plated hardware that allows up to 2” of forward-rearward adjustment

•Optional EZ GLIDE II™ backrest (PART #0822-0133) features multiple detents (with virtually no metal-to-metal contact) for vertical pad adjustment plus fore/aft adjuster

•Both backrests will work in either position•Optional Solo Rear Seat/pillion seat are also available in matching styles and two sizes•Made in the U.S.A.

PART # DESCRIPTION SUG. RETAILFOR 84-99 FXST, FLST MODELS (18” L X 11” W)0802-0618 Smooth $299.950802-0619 Flame stitch 309.95OPTIONAL SOLO REAR SEAT/PILLION PADS0802-0620 Narrow smooth (11” L X 71/2” W) 154.950802-0621 Narrow flame stitch (11” L X 71/2” W) 159.950802-0622 Wide smooth (11” L X 9” W) 189.950802-0623 Wide flame stitch (11” L X 9” W) 194.95

PART # DESCRIPTION SUG. RETAILOPTIONAL BACKRESTS0822-0133 EZ GLIDE II backrest, solar-reflective leather,

smooth (9” W x 51/4” H) $179.950822-0135 EZ GLIDE I backrest w/ pouch, solar-reflective

leather (10” W x 71/2” H) 199.95

PREDATOR SEATS•Solar-reflective leather in the seating area and automotive-grade vinyl on the sides; patented process reduces surface temperature by as much as 25°F for a cooler seat, higher durability and longer life over conventional leather or vinyl

•Custom-molded polyurethane foam for maximum comfort and styling•3/16” ABS thermoformed seat base for a perfect fit•Rubber bumpers and fully carpeted bottom to protect paint•Fit all Drag and most H-D sissy bars•11/2” lower than stock (unless noted)•Include all mounting hardware•Made in the U.S.A.

NOTE: Will also fit 89-93 FLHT models when used with lower dash extension PART #2202-0070.

PART # DESCRIPTION SUG. RETAILFOR 94-96 FLHR MODELS0801-0616 Smooth $289.950801-0617 Flame stitch 299.95

0801-0616 0801-0617

0802-0618 0802-0619

0802-06230822-01330802-0620

0822-0135

6

LINDBY CUSTOMRiders continue to ask for Lindby Custom products by name because they know that Per Lindby, wife Anne and their team are the leaders in engine guard and highway peg design. Their innovative styles not only look great but also function well with bars that include built-in or even fold-down footpegs such as those on the Twinbar®. With something for every ride, mild to wild, your customers will fi nd their perfect bars in this broad line-up.

LINBAR® FRONT HIGHWAY BARS•Made from 1 1/4” high-strength steel for long-lasting durability•Precision bent and welded for a perfect fit every time•Neoprene O-rings provide traction in all climates•Available in a chrome-plated or glossy black powder-coat finish

U.S. Patent #D361311

NOTE: Not recommended for use with extended forward controls or extended floorboards.

PART # DESCRIPTION SUG. RETAILFOR 00-11 FLSTC, FLSTF AND FLSTNDS-190065 Chrome $349.950505-1138 Glossy black powder coat 349.95

0505-1138

ONE-PIECE HEATED TOURING SEATS•Dual-zone high/low heat settings for driver and passenger right on the side of the seat•Illuminated switches•Does not require any OE controllers or switches to function•Constructed with extra rugged, triple-layered fiberglass•Wire harness hooks to accessory port in front of battery; seat has power only when the ignition key is turned on and accessory toggle switch below the handlebars is flipped up

•Mustang’s one-piece touring design provides the rider and passenger with the fullest, most comfortable seat possible

•Baseplate is open in the middle to accept a Mustang or stock H-D driver backrest kit•17” W front bucket, 14” W rear seat•Seat will fit with a handrail•Made in the U.S.A.

PART # DESCRIPTION SUG. RETAILFOR 08-11 FLHT, FLHR, FLTR, FLHX MODELS0801-0601 Plain $749.95

PART # DESCRIPTION SUG. RETAILFOR 08-11 FLHT, FLHR, FLTR, FLHX MODELS (CONT)0801-0602 Studded, chrome $779.95

PART # DESCRIPTION SUG. RETAILFOR 08-11 FLHT, FLHR, FLTR, FLHX MODELS (CONT)0801-0603 Studded, black $779.95

0801-0601

PART # DESCRIPTION SUG. RETAILFOR 08-11 FLHT, FLHR, FLHX, FLTR AND H-D FL TRIKE MODELS1010-1017 Polished silver $229.951010-1018 Matte black 229.95

POWER X INTAKE•Air is power and Boyesen has channeled that power like never before•Patented X-Wing design for more power and acceleration; X-Wing venturi increases air speed for added throttle response

•Complete kit includes backing plate with internal breather passageways, filter and mounting hardware

•Oil-free/washable filter is a poly cotton blend with an extra-large filter area for increased airflow; filters to 40 microns

•Available in polished silver or matte black finish•Accepts stock air filter cover

1010-1017

1010-1018

PART # DESCRIPTIONSUG.

RETAIL1011-2663 For Bendix-Tillotson carbs

to 75 $79.951011-2664 For Linkert early 4-bolt

model carbs 71.95

CUSTOM AIR CLEANER ASSEMBLIES•Increases horsepower with proper carburetor calibration

•Mount directly to the carburetor•Designed to fit most models equipped with various carburetors

1011-2663

1011-2664

7

CLIP-ON HANDLEBARS•A great way to give your bike that custom Cafe Racer look while providing a surprisingly comfortable riding position due to their “zero handlebar drop angle” configuration

•Super-clean design features all-CNC-machined billet aluminum clamps and handlebars and includes superstrong alloy mounting hardware

•Bars are 1” diameter, 12” long aluminum, constructed from strong 1/8” thick-wall 6061 T-6 tubing

•Available in your choice of hard black anodized and raw aluminum finishes

•Made in the U.S.A.

PART # DESCRIPTION SUG. RETAILFOR MODELS WITH 39MM FORK TUBES0601-1710 Black anodized finish $209.950601-1711 Raw aluminum finish 209.95FOR MODELS WITH 41MM FORK TUBES0601-1712 Raw anodized finish 209.950601-1713 Black aluminum finish 209.95

CLIP-ON HANDLEBARS•A great way to give your bike that custom Cafe Racer look

0601-1710

0601-1712GAS CAPS•A great replacement for your hard-to-remove stock gas cap

•Made with finger serrations for a much easier removal over the stock smooth-sided gas cap

•Super-clean and low-profile design features all CNC-machined billet aluminum construction throughout

•After being tightened down, the cap can rotate to any position to align design pattern

•Clear anodized finish•High-quality gas cap base has right-hand threads and is vented•Dimensions: 3” diameter, 1/4” thick at the edge, and 9/16” thick in the center

•Made in the U.S.A.

PART # DESCRIPTION SUG. RETAILFOR L96-11 H-D MODELS0703-0376 JM U.S.A. $59.950703-0377 Joker 59.950703-0378 Smooth 59.95

0703-0376

0703-0377

0703-03770703-0378

BILLET ALUMINUM MIRRORS WITH CLEAR GLASS•Unique stainless steel pivot rides in a special nylon bushing; mirror head will never lose adjustment or rust at the pivot

•Unsightly adjustment screws on the back of the mirror head are eliminated

•CNC-machined from billet aluminum with a chrome or black finish•Can be installed on all 84-11 H-D clutch or brake housings; all necessary hardware included

•Sold each

PART # DESCRIPTIONSUG.

RETAILCHROME0640-0552 Smooth head w/ cutout stem, left; 6” x 41/4” stem length $99.950640-0554 Smooth head w/ cutout stem, right; 6” x 41/4” stem length 99.950640-0556 Ball-milled head w/ ball-milled stem, left; 6” x 41/4”

stem length 99.950640-0558 Ball-milled head w/ ball-milled stem, right; 6” x 41/4”

stem length 99.95BLACK0640-0553 Smooth head w/ cutout stem, left; 6” x 41/4” stem length 99.950640-0555 Smooth head w/ cutout stem, right; 6” x 41/4” stem length 99.950640-0557 Ball-milled head w/ ball-milled stem, left; 6” x 41/4”

stem length 99.950640-0559 Ball-milled head w/ ball-milled stem, right; 6” x 41/4”

stem length 99.95

BILLET ALUMINUM MIRRORS

0640-0552

0640-0555

0640-0557

0640-0558

COMPLETE 41MM FORK TUBE INTERNALS KIT•Contains everything needed to replace all clips, bushings, springs, dampeners, seals and chrome top caps on most Harley-Davidson 41mm fork tubes (except models with cartridge forks)

PART # DESCRIPTION SUG. RETAIL0414-0398 Complete fork tube internals kit $149.95

INTERNALS KIT

PART # DESCRIPTION SUG. RETAIL2120-0382 For 96-06 universal application (except FLT, FLHT,

FLHR, FLHX, FLTR models) $34.952120-0383 For 07-11 universal application (except FLT, FLHT,

FLHR, FLHX, FLTR models) 34.952120-0384 For 96-06 FLT, FLHT, FLHR, FLTR models 59.952120-0385 For 07-11 FLT, FLHT, FLHR, FLTR models 59.95

HANDLEBAR EXTENSION WIRING KITS•Saves time by streamlining handlebar wiring jobs

•Kits include all the materials necessary to extend the wires for hand controls

•Terminals crimped on one end•Cut-to-length design will accommodate up to 20” Apehanger handlebars

•Includes OEM color matching wires and heat shrink•Made in the U.S.A.

TEARDROP 51/2” X 31/2”

2120-0383

8

FRONT FENDERS•Raw stamped steel construction•Measure approximately 6” W (inside)•Available with or without trim holes•Mount with OEM hardware

PART # DESCRIPTION SUG. RETAILFOR 00-11 FLT/FLHT MODELS1401-0317 Fender w/o trim holes; repl. OEM #59045-00 $99.951401-0318 Fender w/ trim holes; repl. OEM #59093-00B 99.95

PART # DESCRIPTION SUG. RETAILFOR 87-99 FLT/FLHT MODELS1401-0323 Fender w/o trim holes; repl. OEM #59045-98 $99.951401-0324 Fender w/ trim holes; repl. OEM #59093-87 99.95

•Raw stamped steel construction

1401-0317

1401-0318

1401-0323

1401-0324

REAR FENDER•Raw stamped steel construction; measures approximately 71/4” wide (inside)

•Original-style fender with taillight mount

•Accepts OEM fender struts and mounting hardware

PART # DESCRIPTION SUG. RETAIL1401-0330 For 82-93 XL models; repl. OEM #59674-81A $99.95

CHROME BRAKE CALIPERS•Direct bolt-on design•Calipers include brake pads and bleeder screws•Sold each

PART # DESCRIPTION SUG. RETAILFRONT FOR 08-11 FLHT, FLTR, FLHR, FLHX AND H-D FL TRIKE1701-0374 Left; repl. OEM #43027-08 $229.951701-0373 Right; repl. OEM #44023-08 229.95REAR CALIPER1701-0375 For 08-11 FLHT, FLTR, FLHR, FLHX;

repl. OEM #44080-08B 229.95

•Calipers include brake pads and bleeder screws

1701-0374

1701-0373

1701-0375

AXLE ADJUSTER SPACERS•Steel construction with a chrome-plated finish

PART # DESCRIPTION SUG. RETAIL0214-0589 For 00-07 FXST/FLST; repl. OEM #47577-00 (pr.) $29.950214-0590 For 08-11 FXST/FLST; repl. OEM #41694-08 (ea.) 13.95

AXLE ADJUSTER SPACERS

0214-0589

0214-0590

PART # DESCRIPTION SUG. RETAIL2104-0227 For 09-11 FLHT, FLHR, FLHX, FLTR and

FL Trike models $19.95

8.8MM SPARK PLUG WIRE SET•Constructed with silicone throughout the jacket, insulation and core to deliver high-temperature resistance

•Rated at SAE Class E J2031 with a continuous operating temperature of 450° F

•Made in the U.S.A.

PART # DESCRIPTION SUG. RETAIL2106-0149 Mini high/low beam toggle switch $9.952106-0150 Mini Air Ride toggle switch 9.95

MINI TOGGLE SWITCHES•5 AMP, 1/4” hole mini toggle switches•Made in the U.S.A.

2106-0149 2106-0150

9

XL CAMS“PB+” EXHAUST CAMS•”PB+” exhaust cams only (#s 1 and 4)•Use with stock P intake cams for bolt-in power with stock 1000cc engines; stock springs are okay and no head work is required

•Made in the U.S.A.

NOTE: 81-E84 cam gear kits (with generators) do not have tachometer drive gears.

PART # DESCRIPTION SUG. RETAIL0925-0589 For L84-85 XL $203.950925-0588 For 81-E84 XL 203.950925-0587 For 57-70 XL 213.95 GRIND OPEN CLOSE DURATION @ .053 VALVE LIFT LIFT @ TDCPB+ EXHAUST CAMSIntake 34° 40° 254° .400 .200Exhaust 43° 31° 254° .410 .192

XL CAMS“Y” CAMS•Biggest available four-cam set that does not require head work; however, some 82 engines may require spring spacing

•Uses stock springs and provides great mid-range and upper-end power

•Use with 9.0:1 to 10.0:1 compression ratios for best power gain

NOTE: 81-E84 cam gear kits (with generators) do not have tachometer drive gears. L84-85 cam gear kits (with alternators) do not have generator.

PART # DESCRIPTION SUG. RETAIL0925-0596 For L84-85 XL $407.950925-0595 For 81-E84 XL 407.950925-0594 For 57-70 XL 427.95 GRIND OPEN CLOSE DURATION @ .053 VALVE LIFT“Y”Intake 35° 47° 262° .425Exhaust 53° 29° 262° .425

PART # DESCRIPTION SUG. RETAILPOLISHED STAINLESS LED BULLET LIGHT KITS2040-0802 W/ standard trim ring and red LED $129.952040-0803 W/ hood trim ring and red LED 129.952040-0804 W/ standard trim ring and amber LED 129.952040-0805 W/ hood trim ring and amber LED 129.95TITANIUM-COATED (BLACK CHROME) LED BULLET LIGHT KITS2040-0806 W/ standard trim ring and red LED 129.952040-0807 W/ hood trim ring and red LED 129.952040-0808 W/ standard trim ring and amber LED 129.952040-0809 W/ hood trim ring and amber LED 129.95

BULLET LED MARKER/SIGNAL LIGHT KITS•Choose kits with standard or hooded bezels, amber or red lights and titanium-coated black chrome or polished stainless steel finish

•Great looking, easy-to-install lights include six pairs of lenses in every kit: flat, domed and bullet, each pair in clear and smoked

•Twenty-five highly visible, vibration-resistant LEDs that will last more than twenty times longer than traditional filament bulbs

•Three-wire design compatible with brake, turn and running light functions

•Corrosion-resistant 304 stainless ring, injection-molded high-impact ABS and polycarbonate internal components and water-resistant wire grommets provide long-lasting durability and IP66 waterproof rating

•Universal post installation is perfect for forward or rearward mounting; hooded trim ring can be set at 12, 3, 6 and 9 o’clock positions

•Kits include two lights, plus instructions, extra mounting studs, wires and two load resistors (if needed to balance the bike’s signal flash rate)

•Measure: 3.25” L x 2” D (standard bezel); 3.5” L x 2” D (hooded bezel)•Not DOT approved

2040-0802

2040-0805

2040-0807

PART # DESCRIPTION SUG. RETAILKITS WITH POLISHED STAINLESS TRIM RING2040-0800 Amber LED $99.952040-0671 Red LED 99.95KITS WITH TITANIUM-PLATED (BLACK CHROME) TRIM RING2040-0801 Amber LED 99.952040-0672 Red LED 99.95

LED SADDLEBAG MARKER/SIGNAL LIGHT KITS•Saddlemen’s new 21/4” flush-mounted LED kits permit easy installation of lights in the back of saddlebags for a clean, custom look

•Kits are available with titanium-coated black chrome or bright polished stainless trim rings with amber lights and multi-faceted clear lenses

•Flush-mounted universal design will mount on the rear surface of most hard or soft saddlebags

•Twenty-five highly visible, vibration-resistant LEDs last more than twenty times longer than traditional filament bulbs

•Three-wire design is compatible with brake, turn and running light functions

•Corrosion-resistant 304 stainless steel mounting ring, injection molded high-impact ABS and polycarbonate internal components and water-resistant power plugs provide long lasting durability and IP66 waterproof rating

•Everything you need for easy installation, including instructions for Saddlemen S4 Rigid-Mount, Specific-Fit Quick-Disconnect and Rigid-Mount Specific-Fit Teardrop saddlebags, two lamps plus wires, waterproof electrical connectors, four load resistors (if needed to balance the bike’s signal flash rate) and gaskets to keep your saddlebag weather-resistant

•Not DOT approved

LED SADDLEBAG MARKER/SIGNAL LIGHT KITS

2040-0671

Shown with one set of 2040-0800 installed in each saddlebag

2040-0801

10

CYCLE ELECTRIC INC.Electronics are the nerve center of any bike and here is a company dedicated to producing the highest quality, longest lasting electrical charging systems and components for American-made V Twins from 1936 to current. They do it all in their Brookville, Ohio factory where all parts are tested individually and then again as an assembly by craftsmen whose goals are both quality and customer service. The results are components with higher output and greater durability than the originals they replace.

components for American-made V Twins from 1936 to current.

REPLACEMENT REGULATORS FOR 3-PHASE 50A CHARGING KITS•Made in the U.S.A.

PART # DESCRIPTION SUG. RETAILREPLACEMENT REGULATORS2112-0711 For kit PART #2112-0412 $215.952112-0712 For kit PART #s 2112-0407, 2112-0408 181.95

PART # DESCRIPTION SUG. RETAILREPLACEMENT REGULATORS (CONT)2112-0713 For kit PART #s 2112-0409, 2112-0410 $193.952112-0714 For kit PART #2112-0411 224.95

REPLACEMENT REGULATORS FOR 3-PHASE 50A CHARGING KITSREPLACEMENT REGULATORS FOR 3-PHASE 50A CHARGING KITS

2112-0711

2112-0712

2112-0713

2112-0714

PART # DESCRIPTION SUG. RETAIL3807-0100 Optimate 4 $74.95

OPTIMATE 4 DUAL PROGRAMWEATHERPROOF DESULFATING BATTERY CHARGER/MAINTAINER•The OptiMate 4 saves neglected, deep-discharged batteries that other smart chargers can’t•Ideal for all AGM, GEL and standard filler cap batteries from 3 to 50aH•IP64 weatherproof sealed enclosure with built-in mounting option•Now compatible with either conventional or CAN-bus motorcycle electrical systems•Control panel with 10 LEDs displays all vital battery information•Cable bushings avoid insulation stress in ultra-cold temperatures•SAE weatherproof connections•Provides optimal maintenance of your battery during long-term storage, achieved by its gentle maintenance cycle which automatically allows the battery to rest for 30 minutes of each hour of the maintenance cycle while it remains connected

•Includes fused eyelet connector for permanent mounting and battery clip set for bench charging

OPTIMATE 4 DUAL PROGRAM

PART # DESCRIPTION SUG. RETAIL3807-0101 Optimate 1 $33.95

OPTIMATE 13-STEP 900MA BATTERY CHARGER/MAINTAINER•Automatic charger for 12V lead-acid batteries of all types, with standard filler caps, or sealed (MF) maintenance-free and GEL

•Ideal for maintaining batteries of seasonally used or stored vehicles of all types

•Three-step charging program ensures effective charging of the battery

•Totally safe for prolonged connection to the battery, without risk of overcharging

•Easy to use, connect to battery, then to the power socket and the rest is automatic

•An auto-resetting thermal fuse switches off the charger’s output circuit if the internal temperature for any reason exceeds a safe limit, to protect the charger from burn-out

•Includes weatherproof connector with eyelets for permanent connection and battery clips for bench charging

11

HI-4N MULTI-FUNCTION PERFORMANCE IGNITION KIT WITH SINGLE-FIRE COIL•HI-4N ignition module features a one-piece machined aluminum housing that reduces vibration and improves heat dissipation and reliability

•Improved kickstart algorithm design – starts as easily as with points•BCD switches with solid detent and legible markings allow easy and repeatable adjustments of mode, advance rate and rev limit

•Single-fire and dual-fire function built into a single module•Flexible wiring harness makes installation easier•Initial timing marks allow precise adjustment and re-installation•Sensor cover integrated into the housing to provide protection during installation

•Kit also includes Crane Cams single-fire coil and Crane Cams 8.5mm double silicone premium quality spark plug wires

•Made in the U.S.A.

PART # DESCRIPTION SUG. RETAIL2101-0266 For 84-99 Big Twin Evolution (except EFI models),

70-84 Shovelhead and 71-03 XL (except 1200S) $475.95

HI-4N IGNITION MODULE•Updated version of the popular Crane HI-4 ignition

•More power than the stock ignition

•Single-fire and dual-fire function built into a single module•All-metal housing provides improved heat dissipation•Ignition advance and timing degree markings are on the metal flange•Convenient cable notch in the housing makes installation easier and prevents damage to the cable

•Sensor and magnet housings are built into the all-metal back plate to protect the sensors from damage during installation

•Sensor housings contain advanced flux concentrators with high-temperature-resistant samarium/cobalt magnets for accurate, reliable ignition triggering

•Electronics are fully enclosed to resist vibration, moisture and dirt•All electronics are mounted directly to the metal housing, which acts as a heat sink

•Four rotary switches for ignition mode selection, advance rate, and rev limit

•Switches provide accurate, repeatable settings•Coil and plug wires are sold separately•Made in the U.S.A.

PART # DESCRIPTION SUG. RETAIL2101-0265 For 84-99 Big Twin Evolution (except EFI models),

70-84 Shovelhead and 71-03 XL (except 1200S) $296.95

PART # DESCRIPTION SUG. RETAIL2105-0107 For 70-78 Shovelhead; will also fit 79-99 Big Twin

(requires mechanical advance) and all 36-69 Knucklehead/Flathead/Panhead/Shovelhead w/ generator if aftermarket timers designed for 12V “cone” style ignition systems $124.95

XR-I POINT REPLACEMENT IGNITION SYSTEM•The easiest points conversion on the market•Remove old points and condensor, install the XR-i on the supplied adapter plate and wiring, and done

•Fits under the stock cone cover so you keep the factory look; perfect for restoration projects

•Has built-in adjustable rev limiter (4000 to 8000 rpm)•Voltage depended dwell control for optimal coil saturation•Operates down to 7V for reliable starting, a must for kick-start engines•Unit is fully sealed from moisture and dirt•Delivers more accurate timing•Made in the U.S.A.

VT-I V-TWIN ELECTRONIC IGNITION SYSTEM•Ultra-reliable dual fire electronic ignition system•Includes special trigger rotor for use with traditional mechanical advance mechanism (sold separately)

•Precise digitally set RPM limiter (200 rpm steps from 5,200 to 7,000 rpm)•Status LED for easy static timing•Electronic dwell control for maximum ignition energy at high rpm and reduced current draw at low RPM

•Compatible with most original equipment and aftermarket dual fire ignition coils (3-5 ohms primary resistance)

•Easy installation – simple two-wire hookup to coil•Hall effect sensor detects teeth on special trigger rotor and provides very stable spark timing

•Operates down to below 6 volts for reliable starting under all conditions, including kick start

•Fully encapsulated construction using surface mount electronics – waterproof and highly resistant to vibration and shock

•Over-temperature protection; rated to operate at 125°C (260°F)

PART # DESCRIPTION SUG. RETAIL2101-0267 For 84-99 Evolution Big Twin, 70-84 Shovelhead

and 86-03 XL (except 1200S) $139.95

12SEPTEMBER 2011 | 9901-1026

HOGTUNESOwner Mike “Pez” Pesdirz and the folks at Hogtunes continue to amaze riders everywhere with their ever expanding line of high-performance audio products and accessories. Their in-house state-of-the-art sound labs mean that they are able to continually develop, test and refi ne products specifi cally designed for motorcyclists. And it is the motorcyclists who own Hogtunes systems who are some of the best salesmen as they have fellow riders asking for Hogtunes by name.

specifi cally designed for motorcyclists. And it is the motorcyclists

MEMPHIS SHADES SPEAKER SYSTEM KIT•Includes custom “pod” with dual 4.25” speaker, 50 watt amp with USB charge port, audio perch with built-in volume control and all required hardware and wiring

•Fits all Memphis Shades Batwing fairings•Measures approximately 1111/16” W x 51/4” T x 51/2” D

NOTE: Kit may not fit if gauges are riser mounted.

” D

DEEP CUT FRONT SPEAKER GRILLES•Made of 6061 T-6 billet aluminum•Sold in pairs•Made in the U.S.A.

PART # DESCRIPTION SUG. RETAILFOR 96-11 FLHT/FLHX AND H-D FL TRIKE MODELS4405-0240 Chrome $139.954405-0239 Black 139.95

DEEP CUT FRONT SPEAKER GRILLES

DEEP CUT OIL PRESSURE GAUGE KITS•Finally a clean way to mount an oil pressure gauge on Big Twin and Sportster engines; bracket mounts gauge to rear rocker box

•Features stainless housing and glass lens filled with vibration dampening glycerin

•Includes a 0-60 lb. liquid-filled gauge, billet bracket/cone, stainless steel hose assembly and necessary hardware

NOTE: Check clearance between gauge and gas tank.

PART # DESCRIPTION SUG. RETAIL2212-0370 For 99-11 Twin Cam $189.952212-0371 For 93-03 XL w/ mid controls only 199.952212-0369 For S&S w/ billet rocker boxes 189.95

2212-0370

4405-0239

4405-0240

PART # DESCRIPTION SUG. RETAILCHROME3501-0696 W/ cut-outs, for dual exhausts $399.953501-0697 W/ cut-out, for right exhaust 399.953501-06981 W/o cut-out 399.95

PART # DESCRIPTION SUG. RETAILBLACK3501-0699 W/ cut-outs, for dual exhausts $399.953501-0700 W/ cut-out, for right exhaust 399.953501-07011 W/o cut-out 399.951 For use with short turn-down mufflers.

BILLET SADDLEBAG EXTENSIONS•Chrome-plated, billet aluminum extensions create a custom look

•Easy bolt-on installation to any 93-11 FL model with hard saddlebags•No painting required•Available with exhaust cut-outs for single or dual exhaust systems or without cutouts for “shorty” exhausts•Available in chrome plated or black powder-coat finish with contrasting machined grooves•Made in the U.S.A.

SUG. RETAIL

3501-0696

3501-0697

3501-0698

3501-0699

PART # DESCRIPTION SUG. RETAIL4405-0218 Memphis Shades speaker system kit $399.95