self contained units - 90ma - heinen & hopman · self contained units 90ma self-contained...
TRANSCRIPT
>
Ventilation Air Conditioning RefrigerationHeating
22ºCInside
OUTSIDEHUMIDITY
PROVIDED BYHEINEN & HOPMAN
35 C
90%
productsself contained units - 90MA self-contained marine air conditioning unit
Self contained unitS
90Ma self-contained marine type air conditioning unit
• Nominal cooling loads: 10.5 kW / 35.1 kW • Refrigerant R134a, R404a, R407• Easely removable panels for inspection and maintenance• For duct or free blow applications• Units supplied factory pre-charged only requiring suitable water and electrical connections• Electrical supply o 230V 3ph 60Hz o 460V 3ph 60Hz o 380 3ph 50Hz• Other options available o Electric heating o Fresh-water and sea-water tube condenser o Pre-wired
dimensions Sizes in millimeter
Model
*4 *6 *8 *12
A 918 1226
B 549 759
C 1505 1828
D See Note 2
E 51
F 286 343 397
G 330 394 466
H 19 19 25
J 294 263 289
K 435 615
L 519 646
M 435 435
Alternatives available on request.Due to continuous product development, Heinen & Hopman reserves the right to introduce alterations without prior notice.
noteS
1. Certified dimension drawings available on request.2. The minimum required clearance at the back of unit is zero. Clearance above and at right (90MA*8, *12 only) and at left of the unit depends on space required for accessory plenum, ductwork, condenser piping, accessory heater piping, condensate drain line and power wiring.3. Water connections are located on left side of unit (Refer to “Make Condenser Connection”, Condensate drain connections are located on left side of unit for *4 & *6 and on both sides of unit for *08 & *12.
FIGURE 1 - BASE UNIT INTERIOR DETAILS(TYPICAL UNIT SHOWN)
Step 4 - Rig and Place Unit -
NOTE: Install accessories before placing unit.
a. Provide space around unit for service, filter access, andoverhead clearance as indicated in Figure 2.
b. Move and store unit in upright position.c. Use slings with spacer under base skid to prevent panel
damage when using hoist.d. Units as shipped are adequately dampened against
vibration. If additional dampening is desired, placesponge rubber or rubber mat, between deck and base ofunit or install vibration isolators.
e. Unit should be level. Unit leveling tolerance is 1/8 in. perlinear ft in any direction.
Step 5 - Install Accessory Plenum (If Supplied) - Useplenum as template to mark hole locations in top panel. Drill0.154-in. holes in top panel at marked locations and attachplenum with screws supplied.
UNIT *04 *06 *08,*12ABC
36.13(918)21.63(549)59.25(1505)
48.26(1226)29.88(759)72.00(1828)
D SEE NOTE 2E 24(51)FGHJ
11.25(286)13.00 (330)
0.75(19)11.59(294)
13.50(343)15.50(394)0.75(19)
10.34(263)
15.63(397)18.38(466)1.00 (25)
11.37(289)KLM
17.13(435)20.38(519)17.11(435)
24.20(615)25.50(646)17.11(435)
NOTES:1. Certified dimension drawings available upon request2. Minimum required clearance at back of unit is zero.
Clearance above and at right (90MA*08,*12 only) and atleft of unit depends on space required for accessoryplenum, ductwork, condenser piping, accessory heaterpiping, condensate drain line and power wiring
3. Water connections are located on left side of unit (Referto “Make Condenser Connections”, Condensate drainconnections are located on left side of unit for *04 & *06,and on both sides of unit for *08 & *12.
FIGURE 2 - UNIT DIMENSIONS
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligationsPrinted in U.S.A. 90MA-3SI SUPERCEDES FORM 62-02971-00 09-2009Pg 8
R - 22 - Metric units R - 404A - Metric units R - 407C - Metric units
BASE UNIT 90ma/mu UNITS 204 206 208 212 504 506 508 512 404 406 408 412
Nominal capacity kW 10.5 17.6 26.4 35.1 10.5 17.6 26.4 35.1 10.5 17.6 26.4 35.1
OPERATING WEIGHT
Base unit -- 90MA kg 177 194 406 431 177 194 406 431 177 194 406 431
Base unit -- 90MU kg 150 163 379 404 150 163 379 404 150 163 379 404
Discharge plenum kg 11.3 11.3 22.7 22.7 11.3 11.3 22.7 22.7 11.3 11.3 22.7 22.7
COMPRESSOR TYPE Welded hermetic Scroll Semi-hermetic Reciprocating Welded hermetic Scroll Semi-hermetic Reciprocating Welded hermetic Scroll Semi-hermetic Reciprocating
Quantity of cylinders - - 4 6 -- -- 4 6 -- -- 4 6
Quantity of unloading cylinders - - 0 2 -- -- 0 2 -- -- 0 2
Quantity of capacity steps - - 1 2 -- -- 1 2 -- -- 1 2
DICHARGE PRESSURE SWITCH
Opens -- 90MA kPa 2725 ± 69 2725 ± 69 2725 ± 69
Closes -- 90MA- kPa 2034 ± 138 2034 ± 138 2034 ± 138
Opens -- 90MU kPa 2937 ± 48 2937 ± 48 2937 ± 48
Closes -- 90MU- kPa 2206 ± 138 2206 ± 138 2206 ± 138
SUCTION PRESSURE SWITCH
Opens kPa 186 ± 28 186 ± 28 186 ± 28
Closes kPa 462 ± 48 462 ± 48 462 ± 48
OPERATING CHARGE -- 90MA kg 1.4 2.4 5.1 4.5 1.4 2.4 5.1 4.5 1.4 2.4 5.1 4.5
CONDENSER -- 90MA
Number... Type 1... Tube-in-tube
Water volume I 1.48 3.3 9.2 1.48 3.3 9.2 1.48 3.3 9.2
EVAPORATOR AIR FAN Adjustable, belt-driven centrifugal: 1750 RPM motor @ 60 Hz
Nominal flow m3/h 1698 2830 4245 5660 1698 2830 4245 5660 1698 2830 4245 5660
Standard speed range RPM
427-652 593-762 412-583 500-708 427-652 593-762 412-583 500-708 427 - 652 593 - 762 412 - 583 500 - 708
Maximum allowable RPM 1050
Belt quantity / Pulley pitch diameter cm 1 / 20.3 1 / 16.3 1 / 21.6 1 / 17.8 1 / 20.3 1 / 16.3 1 / 21.6 1 / 17.8 1 / 20.3 1 / 16.3 1 / 21.6 1 / 17.8
Motor pulley pitch diameter range cm 6.1 - 8.6 6.1 - 8.6 6.1 - 8.6
Motor nominal rating (@ 60 Hz) ...Frame Size
Standard kW .25 / 56 .56 / 56 .75 / 56 1.5 / 56 .25 / 56 .56 / 56 .75 / 56 1.5 / 56 .25 / 56 .56 / 56 .75 / 56 1.5 / 56
Alternate (See Note 1) kW .56 / 56 .75 / 56 1.5 / 56 2.2 / 56 .56 / 56 .75 / 56 1.5 / 56 2.2 / 56 .56 / 56 .75 / 56 1.5 / 56 2.2 / 56
Alternate (See Note 1) kW ---- ---- 2.2 / 56 ---- ---- ---- 2.2 / 56 ---- ---- ---- 2.2 / 56 ----
EVAPORATOR COIL 3/8 (.95 cm) OD, Copper tubes, Aluminium fins
Tube type Prime
Quantity of rows... Fin spacing cm 2...5.7 3...5.7 3...4.9 2...5.7 3...5.7 3...4.9 2...5.7 3...5.7 3...4.9
Face area Sq m 0.46 0.46 0.68 0.79 0.46 0.46 0.68 0.79 0.46 0.46 0.68 0.79
RETURN AIR FILTERS Factory-supplied, cleanable
Quantity... Size cm 2...40.6 x 63.5 x 2.5 4...40.6 x 50.8 x 2.5 2...40.6 x 63.5 x 2.5 4...40.6 x 50.8 x 2.5 2...40.6 x 63.5 x 2.5 4...40.6 x 50.8 x 2.5
CONDENSER CONNECTIONS
Water inlet (bottom) & outlet (top) inch
1/2 3/4 1 1 1/2 3/4 1 1 1/2 3/4 1 1
Maximum working pressure kPa(refrigerant side)
2758 2758 2758
CRETURNONDENSATE DRAIN inch CONNECTIONS
3/4 3/4 3/4
LEGEND FPT = Female Pipe Thread I MPT = Male Pipe Thread I ODF = Outside Diameter Female NOTE 1: Motors and drives other than those supplied with the unit must be purchased separately. Contact your Carrier Transicold representative
LEGEND FPT = Female Pipe Thread I MPT = Male Pipe Thread I ODF = Outside Diameter Female NOTE 1: Motors and drives other than those supplied with the unit must be purchased separately. Contact your Carrier Transicold representative
Alternatives available on request.Due to continuous product development, Heinen & Hopman reserves the right to introduce alterations without prior notice.
R - 134A - Metric units
BASE UNIT 90ma/mu UNITS 308 312
Nominal capacity kW 19.3 28.1
OPERATING WEIGHT
Base unit kg 406 431
Discharge plenum kg 22,7 22,7
COMPRESSOR TYPE Semi-hermetic
Quantity of cylinders 4 6
Quantity of unloading cylinders 0 2
Quantity of capacity steps 1 2
DICHARGE PRESSURE SWITCH
Opens kPa 2310 ± 69
Closes kPa 1620 ± 138
SUCTION PRESSURE SWITCH
Opens kPa 48 ± 21
Closes kPa 152 ± 35
OPERATING CHARGE -- 90MA kg 5.1 4.5
CONDENSER
Number... Type 1... Tube-in-tube
Water volume I 9.2
EVAPORATOR AIR FAN Adjustable, belt-driven centrifugal: 1750 RPM motor @ 60 Hz
Nominal flow m3/h 4245 5660
Standard speed range RPM 412 - 583 500 - 708
Maximum allowable RPM 1050
Belt quantity / Pulley pitch diameter cm 1 / 21.6 1 / 17.8
Motor pulley pitch diameter range cm 6.1 - 8.6
Motor nominal rating (@ 60 Hz)... Frame Size
Standard kW .75 / 56 1.5 / 56
Alternate (See Note 1) kW 1.5 / 56 2.2 / 56
Alternate (See Note 1) kW 2.2 / 56 ----
EVAPORATOR COIL 3/8 OD, Copper tubes, Aluminium fins
Tube type
Quantity of rows... Fin spacing cm 3... 4.9
Face area Sq m 0.68 0.79
RETURN AIR FILTERS Factory-supplied, cleanable
Quantity... Size cm 4... 40.6 x 50.8 x 2.5
CONDENSER CONNECTIONS
Water inlet (bottom) & outlet (top) inch 1 1
Maximum working pressure kPa(refrigerant side)
2758
CRETURNONDENSATE DRAIN inch CONNECTIONS
3/4
www.heinenhopman.com
Heinen & Hopman encourages a more
sustainable world. By providing eco-friendly solutions and serviceswe offer our clients
the option of reducing energy consumption
and thus co2 emissions. Visit
greenmanifest.info for more information.
BrazilT: +5521 3587 4241/4244E: [email protected]
france - la ciotatT: +334 4204 8685E: [email protected]
france - GrasseT: +336 3090 7786 E: [email protected]
GermanyT:+49 4073 1680E: [email protected]
indiaT: +9133 6499 1293E: [email protected]
italyT: +3901 8745 7970E: [email protected]
the netherlands (HQ)T: +313 3299 2500E: [email protected]
the netherlands (Rotterdam)T: +317 8890 8050E: [email protected]
norwayT: +47 6919 0900E: [email protected]
Peoples Republic of chinaT: +8621 3253 2896E: [email protected]
Peoples Republic of chinaT: +86 510 8528 1763E: [email protected]
PolandT: +489 1433 1800E: [email protected]
RomaniaT: +402 3644 8222E: [email protected]
RussiaT: +7 (4012) 308 801E: [email protected]
SingaporeT: +65 6897 7879E: [email protected]
South KoreaT: +8270 4901 0000E: [email protected]
SpainT: +349 3225 9668E: [email protected]
SwedenT: +46 3121 7500E: [email protected]
turkeyT: +9021 6493 8118E: [email protected]
uae (abu dhabi) T:+971 2550 4147E: [email protected]
uae (dubai)T: +971 4263 5453E: [email protected]
uSa - fort lauderdale, floridaT: +195 4463 0110E: [email protected]
uSa - Houma, louisiana T: +198 5876 7989E: [email protected]