seed and fertilizer rate charts for planters with wsmt3 ...verify the suitability and setup of your...

Table of Contents

Table of Contents

Manufacturing, Inc.www.greatplainsmfg.com

ENORIGINAL INSTRUCTIONS

© Copyright 2019 Printed 6/20/19 411-652b

Seed and Fertilizer Rate Chartsfor Planters with WSMT3 (Version 3)Individual Row Control / Hydraulic DriveThe following pages are to assist in the proper setting of seeding andfertilizer rates for planters using DICKEY-john WSMT3 terminals withIndividual Row Control or hydraulically driven meters. To assure themost accurate seeding rates, Great Plains recommends checkingsingulated rates and calibrating for fertilizer application rate at the timeof planting.

http://www.greatplainsmfg.com

WSMT3 (Version 3) Planters Cover Table of Contents

Great Plains | 411-652b | 6/20/19 Cover ii

© Copyright 2018, 2019. All rights Reserved

Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has beentaken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumedfor damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its productsas it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.

Trademarks of Great Plains Manufacturing, Inc. include: AccuShot, Max-Chisel, Row-Pro, Singulator Plus, Short Disk, Swath Command, Terra-Tine, Ultra-Chisel, and X-Press.

Registered Trademarks of Great Plains Manufacturing, Inc. include: Air-Pro, Clear-Shot, Discovator, Great Plains, Land Pride, MeterCone, Nutri-Pro, Seed-Lok, Solid Stand, Terra-Guard, Turbo-Chisel, Turbo-Chopper, Turbo-Max, Turbo-Till, Ultra-Till, Whirlfilter, and Yield-Pro.

Brand and Product Names that appear and are owned by others are trademarks of their respective owners.Printed in the United States of America

Table of Contents

Singulated Planting Overview ...............................................1Singulated Rate Setting Summary ....................................1Population Reference Information .....................................1

Seeds per Unit............................................................1Seed Spacing .............................................................1

Meter Disk Selection..........................................................4Meter Pressurization..........................................................8

Initial Meter Pressurization: Cotton ............................8Initial Meter Pressurization: Milo ................................8Initial Meter Pressurization: Soybeans .......................8Initial Meter Pressurization: Sunflower .......................8Initial Meter Pressurization: Round Corn....................9Initial Meter Pressurization: Flat Corn ........................9Initial Meter Pressurization: Round Corn - Metric.....10Initial Meter Pressurization: Flat Corn - Metric .........10

Planting Rate.........................................................................11Checking Singulated Rates ......................................11

Monitor Configuration ......................................................12Material Seeding Setup ...................................................13Meter RPM Limit Charts ..................................................14

Meter RPM Limits: Corn 24 Cell...............................14Meter RPM Limits: Corn 40 Cell...............................15Meter RPM Limits: Medium Edible Bean..................16Meter RPM Limits: Large Edible Bean .....................17Meter RPM Limits: Cotton ........................................18Meter RPM Limits: Milo 30 Cell ................................19Meter RPM Limits: Milo 65 Cell ................................20

Meter RPM Limits: Milo 130 Cell..............................21Meter RPM Limits: Soybean 84 Cell ........................22Meter RPM Limits: Soybean 168 Cell ......................23Meter RPM Limits: Sunflower 24 Cell ......................24Meter RPM Limits: Sunflower 60 Cell ......................25Meter RPM Limits: Canola 150 Cell .........................26Meter RPM Limits: Canola 250 Cell .........................27Meter RPM Limits: Hill-Drop Cotton .........................28Meter RPM Limits: Industrial Hemp 5 Cell ...............29Meter RPM Limits: Industrial Hemp 30 Cell .............30

Dry Fertilizer..........................................................................31Dry Fertilizer Rate Adjustment .................................31Fertilizer Density Adjustment ...................................31Dry Fertilizer Rate Charts.........................................31

Liquid Fertilizer.....................................................................32Orifice Plate Selection..............................................32

Hydraulic Drive Fertilizer Rate.........................................33Ground Drive Fertilizer Rate............................................33

Orifice Plate..............................................................34Slide Chart - Liquid Fertilizer Rate ...........................34Charts - Liquid Fertilizer Rate ..................................35Setting Relief Valve..................................................36

Strainer............................................................................36Seed Lubricants....................................................................37

Seed Lubricants ..............................................................37Furrow Check - Metric..............................................37

WSMT3 (Version 3) Planters Table of Contents Singulated Planting Overview

Singulated Planting Overview

The information in this section covers important setupand checking information that applies to the Air-Pro®

Meter when planting at one seed per disk cell, using theIRC drive.

Singulated planting employs the seed monitor in:

• Individual Row Control mode.

Singulated Rate Setting Summary1. For your crop, determine your intended population,

in seeds/acre or seeds/hectare. If you know only theseed spacing or population in pounds/acre or kg/acre, consult the charts on page 1 through page 4.

2. For your crop, population and desired field speed,verify the suitability and setup of your seed disk.

3. Set meter rate. See page 12 for more information.

4. Set initial seed inlet shutter per seed rate chart.Set initial meter pressurization per page 8, 9.

5. Verify your planting rate per the instructions at:“Checking Planting Rate” on page 11. If the resultsare consistent with your setup, plant the crop.

Population Reference InformationSeeds per UnitIf only weight (pounds/acre or kilograms/hectare) isknown, obtain the population count by multiplying theweight by the “Kernels per pound” value from the seedcontainer.

Seed SpacingIf only seed spacing is known, use the tables on the nextfive pages to determine population.

Kernels Per Pound

Figure 1Air-Pro® Seed Meter

29626

Example: MiloTarget rate: 4.5 pounds/acreSeed density: 14500 seeds/poundPopulation: = Rate x Density

= 4.5 x 14500, or:65250 seeds/acre

80,000 Seed Kernels 80,000 Seed Kernels

Bag Weight per Pound Bag Weight per Pound

67.5 lbs 1,185 45.0 lbs 1,778

65.0 lbs 1,231 42.5 lbs 1,882

62.5 lbs 1,280 40.0 lbs 2,000

60.0 lbs 1,333 37.5 lbs 2,133

57.5 lbs 1,391 35.0 lbs 2,286

55.0 lbs 1,455 32.5 lbs 2,462

52.5 lbs 1,524 30.0 lbs 2,667

50.0 lbs 1,600 27.5 lbs 2,909

47.5 lbs 1,684 25.0 lbs 3,20029649

Great Plains | 411-652b | 6/20/19 Table of Contents 1


Low Range Seed Spacing Chart U.S. Customary Units

Row SpacingsTwin Row Single Row

20 in. 30 in. 36 in. 38 in. 40 in.Plant 10 in. 15 in. 20 in. 22 in. 30 in. 36 in. 38 in. 40 in.

Population Rows Rows Rows Rows Rows Rows Rows Rows(seeds/acre) Seed Spacing (inches)

14 000 44.8 29.9 24.9 23.6 22.4 20.4 14.9 12.4 11.8 11.215 000 41.8 27.9 23.2 22.0 20.9 19.0 13.9 11.6 11.0 10.516 000 39.2 26.1 21.8 20.6 19.6 17.8 13.1 10.9 10.3 9.817 000 36.9 24.6 20.5 19.4 18.4 16.8 12.3 10.2 9.7 9.218 000 34.8 23.2 19.4 18.3 17.4 15.8 11.6 9.7 9.2 8.719 000 33.0 22.0 18.3 17.4 16.5 15.0 11.0 9.2 8.7 8.320 000 31.4 20.9 17.4 16.5 15.7 14.3 10.5 8.7 8.3 7.821 000 29.9 19.9 16.6 15.7 14.9 13.6 10.0 8.3 7.9 7.522 000 28.5 19.0 15.8 15.0 14.3 13.0 9.5 7.9 7.5 7.123 000 27.3 18.2 15.2 14.4 13.6 12.4 9.1 7.6 7.2 6.824 000 26.1 17.4 14.5 13.8 13.1 11.9 8.7 7.3 6.9 6.525 000 25.1 16.7 13.9 13.2 12.5 11.4 8.4 7.0 6.6 6.326 000 24.1 16.1 13.4 12.7 12.1 11.0 8.0 6.7 6.3 6.027 000 23.2 15.5 12.9 12.2 11.6 10.6 7.7 6.5 6.1 5.828 000 22.4 14.9 12.4 11.8 11.2 10.2 7.5 6.2 5.9 5.629 000 21.6 14.4 12.0 11.4 10.8 9.8 7.2 6.0 5.7 5.430 000 20.9 13.9 11.6 11.0 10.5 9.5 7.0 5.8 5.5 5.231 000 20.2 13.5 11.2 10.6 10.1 9.2 6.7 5.6 5.3 5.132 000 19.6 13.1 10.9 10.3 9.8 8.9 6.5 5.4 5.2 4.933 000 19.0 12.7 10.6 10.0 9.5 8.6 6.3 5.3 5.0 4.834 000 18.4 12.3 10.2 9.7 9.2 8.4 6.1 5.1 4.9 4.635 000 17.9 11.9 10.0 9.4 9.0 8.1 6.0 5.0 4.7 4.536 000 17.4 11.6 9.7 9.2 8.7 7.9 5.8 4.8 4.6 4.437 000 17.0 11.3 9.4 8.9 8.5 7.7 5.7 4.7 4.5 4.238 000 16.5 11.0 9.2 8.7 8.3 7.5 5.5 4.6 4.3 4.139 000 16.1 10.7 8.9 8.5 8.0 7.3 5.4 4.5 4.2 4.040 000 15.7 10.5 8.7 8.3 7.8 7.1 5.2 4.4 4.1 3.941 000 15.3 10.2 8.5 8.1 7.6 7.0 5.1 4.2 4.0 3.842 000 14.9 10.0 8.3 7.9 7.5 6.8 5.0 4.1 3.9 3.743 000 14.6 9.7 8.1 7.7 7.3 6.6 4.9 4.1 3.8 3.644 000 14.3 9.5 7.9 7.5 7.1 6.5 4.8 4.0 3.8 3.645 000 13.9 9.3 7.7 7.3 7.0 6.3 4.6 3.9 3.7 3.546 000 13.6 9.1 7.6 7.2 6.8 6.2 4.5 3.8 3.6 3.447 000 13.3 8.9 7.4 7.0 6.7 6.1 4.4 3.7 3.5 3.348 000 13.1 8.7 7.3 6.9 6.5 5.9 4.4 3.6 3.4 3.349 000 12.8 8.5 7.1 6.7 6.4 5.8 4.3 3.6 3.4 3.250 000 12.5 8.4 7.0 6.6 6.3 5.7 4.2 3.5 3.3 3.1

32320A



High Range Seed Spacing Chart U.S. Customary Units

Row SpacingsTwin Row Single Row

20 in. 30 in. 36 in. 38 in. 40 in.Plant 10 in. 15 in. 20 in. 22 in. 30 in. 36 in. 38 in. 40 in.

Population Rows Rows Rows Rows Rows Rows Rows Rows(seeds/acre) Seed Spacing (inches)

50 000 12.5 8.4 7.0 6.6 6.3 5.7 4.2 3.5 3.3 3.155 000 11.4 7.6 6.3 6.0 5.7 5.2 3.8 3.2 3.0 2.960 000 10.5 7.0 5.8 5.5 5.2 4.8 3.5 2.9 2.8 2.665 000 9.7 6.4 5.4 5.1 4.8 4.4 3.2 2.7 2.5 2.470 000 9.0 6.0 5.0 4.7 4.5 4.1 3.0 2.5 2.4 2.275 000 8.4 5.6 4.6 4.4 4.2 3.8 2.8 2.3 2.2 2.180 000 7.8 5.2 4.4 4.1 3.9 3.6 2.6 2.2 2.1 2.085 000 7.4 4.9 4.1 3.9 3.7 3.4 2.5 2.0 1.9 1.890 000 7.0 4.6 3.9 3.7 3.5 3.2 2.3 1.9 1.8 1.795 000 6.6 4.4 3.7 3.5 3.3 3.0 2.2 1.8 1.7 1.7

100 000 6.3 4.2 3.5 3.3 3.1 2.9 2.1 1.7 1.7 1.6105 000 6.0 4.0 3.3 3.1 3.0 2.7 2.0 1.7 1.6 1.5110 000 5.7 3.8 3.2 3.0 2.9 2.6 1.9 1.6 1.5 1.4115 000 5.5 3.6 3.0 2.9 2.7 2.5 1.8 1.5 1.4 1.4120 000 5.2 3.5 2.9 2.8 2.6 2.4 1.7 1.5 1.4 1.3125 000 5.0 3.3 2.8 2.6 2.5 2.3 1.7 1.4 1.3 1.3130 000 4.8 3.2 2.7 2.5 2.4 2.2 1.6 1.3 1.3 1.2135 000 4.6 3.1 2.6 2.4 2.3 2.1 1.5 1.3 1.2 1.2140 000 4.5 3.0 2.5 2.4 2.2 2.0 1.5 1.2 1.2 1.1145 000 4.3 2.9 2.4 2.3 2.2 2.0 1.4 1.2 1.1 1.1150 000 4.2 2.8 2.3 2.2 2.1 1.9 1.4 1.2 1.1 1.0155 000 4.0 2.7 2.2 2.1 2.0 1.8 1.3 1.1 1.1 1.0160 000 3.9 2.6 2.2 2.1 2.0 1.8 1.3 1.1 1.0 1.0165 000 3.8 2.5 2.1 2.0 1.9 1.7 1.3 1.1 1.0 1.0170 000 3.7 2.5 2.0 1.9 1.8 1.7 1.2 1.0 1.0 0.9175 000 3.6 2.4 2.0 1.9 1.8 1.6 1.2 1.0 0.9 0.9180 000 3.5 2.3 1.9 1.8 1.7 1.6 1.2 1.0 0.9 0.9185 000 3.4 2.3 1.9 1.8 1.7 1.5 1.1 0.9 0.9 0.8190 000 3.3 2.2 1.8 1.7 1.7 1.5 1.1 0.9 0.9 0.8195 000 3.2 2.1 1.8 1.7 1.6 1.5 1.1 0.9 0.8 0.8200 000 3.1 2.1 1.7 1.7 1.6 1.4 1.0 0.9 0.8 0.8225 000 2.8 1.9 1.5 1.5 1.4 1.3 0.9 0.8 0.7 0.7250 000 2.5 1.7 1.4 1.3 1.3 1.1 0.8 0.7 0.7 0.6275 000 2.3 1.5 1.3 1.2 1.1 1.0 0.8 0.6 0.6 0.6300 000 2.1 1.4 1.2 1.1 1.0 1.0 0.7 0.6 0.6 0.5

32320B



Meter Disk Selection



Meter Disk Selection (continued)



Meter PressurizationRefer to the Operator Manual for the procedure for finetuning meter pressurization.

Start with pressures from page 9 and page 10, which arebased on crop, and for corn, seed shape and density.

Note: These are suggested initial (starting) pressures. Use the seed monitor console to adjust them up or down per the procedure in the YP1625A Operator Manual.

Corn: Reading a Pressure Chart (below, next page)1. Pick the chart based on seed shape (flat, round).

Example: large round corn

2. Pick a line based on seed size (large, small).Example: the right line below

3. Find the seed density on the bottom scale.Example: 1260 seeds/pound

4. Read the suggested starting pressure on the left scale, where the line (example shown as dotted gray) intersects the density.Example: 3.4 inches of water

Initial seed inlet Shutter for corn is: 3

Initial Meter Pressurization: Cotton1.5 inches of water (any seed density)Initial seed inlet Shutter: 2

Initial Meter Pressurization: Milo1.5 inches of water (all disk, any seed density)Initial seed inlet Shutter: 1

Initial Meter Pressurization: Soybeans2.0 inches of water (84 cell disk, any seed density)3.0 inches of water (168 cell disk, any seed density)Initial seed inlet Shutter: 2

Initial Meter Pressurization: SunflowerDisk: 817-851C SUNFLOWER OIL LARGE8500 seeds/pound (or fewer)8500 - 7000 s/lb1.25 inches of water7000 - 5500 s/lb1.75 inches of water5500 s/lb and fewer2.25 inches of waterAdjust pressure as needed for desired population.Initial seed inlet Shutter:2

Factory Default Air Control Channel Screens

Material Channel Setup Control Channel 2 Setup



Initial Meter Pressurization: Round Corn

Initial Meter Pressurization: Flat Corn29725

0

0.5

1

1.5

2

2.5

3

3.5

4

4.5

5

90011001300150017001900210023002500270029003100

Seeds Per PoundUnit Weight (80K)

Linear (Round Corn Large)Linear (Round Corn Small)

Met

er P

ress

ure

(in/w

ater

)

5

4.5

3.5

3

2.5

2

1.5

1

0.5

0

88.972.761.553.347.142.138.134.832.029.627.625.8

4 817-794C & 817-796CRound Corn-Large

817-795C & 817-797CRound Corn-Small

Meter P

ressure (in/water)

Disks

Disks

ExampleE

xam

ple

Me

ter

Pre

ssu

rizat

ion

in in

ches

of W

ate

r Meter P

ressurizatio

n in inche

s of W

ater

29726

0

0.5

1

1.5

2

2.5

3

3.5

4

4.5

5

90011001300150017001900210023002500270029003100


Met

er P

ress

ure

(in/w

ater

)

Linear (Flat Corn Large)Linear (Flat Corn Small)

5

4.5

4

3.5

3

2.5

2

1.5

1

0.5

0

88.972.761.553.347.142.138.134.832.029.627.625.8

817-836C & 817-838CFlat Corn-Large

817-795C & 817-797CFlat Corn-Small

Meter P

ressure (in/water)

Disks

Disks

Met

er P

ress

uriz

atio

n in

inch

es o

f W

ate

r Meter P

ressuriza

tion in inche

s of W

ater



Initial Meter Pressurization: Round Corn - Metric

Initial Meter Pressurization: Flat Corn - Metric

0

0.5

1

1.5

2

2.5

3

3.5

4

4.5

5

90011001300150017001900210023002500270029003100

Seeds Per PoundU it W i ht (80K)

Linear (Round Corn Large)Linear (Round Corn Small)

Met

er P

ress

ure

(in/w

ater

)

5

4.5

3.5

3

2.5

2

1.5

1

0.5

0

88.972.761.553.347.142.138.134.832.029.627.625.8

4 817-794C & 817-796CRound Corn-Large

817-795C & 817-797CRound Corn-Small

Meter P

ressure (in/water)

Disks

Disks

6800 6400 6000 5500 5100 4600 4200 3700 3300 2900 2400 2000

Overlay for

31441 Seeds Per Kilogram 29725

ExampleE

xam

ple

Me

ter

Pre

ssu

rizat

ion

in in

ches

of W

ate

r Meter P

ressurizatio

n in inche

s of W

ater

29726

0

0.5

1

1.5

2

2.5

3

3.5

4

4.5

5

90011001300150017001900210023002500270029003100


Met

er P

ress

ure

(in/w

ater

)

Linear (Flat Corn Large)Linear (Flat Corn Small)

5

4.5

4

3.5

3

2.5

2

1.5

1

0.5

0

88.972.761.553.347.142.138.134.832.029.627.625.8

817-836C & 817-838CFlat Corn-Large

817-795C & 817-797CFlat Corn-Small

Meter P

ressure (in/water)

Disks

Disks

Met

er P

ress

uriz

atio

n in

inch

es

of

Wat

erM

eter Pressurization in inches of W

ater

6800 6400 6000 5500 5100 4600 4200 3700 3300 2900 2400 2000

Overlay for

31441 Seeds Per Kilogram 29725


WSMT3 (Version 3) Planters Table of Contents Planting Rate

Planting Rate

Singulated seed charts are based on cleaned and sizedseed singulated with the recommended disk. Extremeseed size variations and foreign material can affect theplanting rate.

Any material difference between chart and field ratesimplies a mechanical malfunction, a planter setup error,unsuitable planting conditions (such as excessive tireslippage) or extremely worn planter components. Youcan verify your setup and planter performance bymeasuring seed placement and spacing over a relativelyshort distance.

The column to the right provides example data for a ratecheck.

Checking Singulated Rates

For metric singulated rate information, see page 37.

1. Determine the sample distance to check. Find yourrow spacing in the table at right.

2. Note the number of rows to sample. Adjust theplanting depth to a shallow setting on one or twooutside rows (per table). Tie up the press wheel armswith wire or bungee to prevent furrow closure.

3. For populations above 100 000 seeds/acre, use asample size of 1/1000th acre.

For populations below 100 000 seeds/acre, use asample size of 1/200th acre.

4. Configure the planter for the chart rate, selecting therate on the seed monitor.

5. Plant at the desired planting speed for slightly morethan the computed sample run length.

6. Measure off the sample distance, balanced inbetween where seeding started and stopped.

7. Count the number of seeds over the distancemeasured. Also note the consistency of the seedspacing.

8. Compute the rate for a full acre or hectare.

For a 1/1000th sample, multiply the counted seedsby 1000.

For a 1/200th sample, multiply the counted seeds by200.

9. If the field and chart rates vary by more than a fewpercent, re-check planter setup, including meter diskor cell count, air system, tire size, tire pressures,sprocket or hydraulic drive setup, chain slack, etc. Ifseed spacing is irregular, this suggests a seeddelivery problem, and not a rate setup problem.

10. While planting, pay attention to the seed monitor. Inaddition to confirming the single-row furrow check, itwill also provide field rate data on all the other rows,and alert you to any irregularities or stoppages.

Example:Planter: YP1625-1630

Crop: SoybeansDensity: 3000 seeds/lbSeed Disk: 817-798C

Target Population:123,000 seeds/acre

Maximum Planting Speed:5 mph

Chart Seed Spacing:1.7 in

Rows to Sample Length of Sample Run

Row Row 1/1000th 1/200thSpacing* Count Acre Acre

7.5in Single 4 17ft 5in

8in Single 4 16ft 4in

9.5in Single 4 13ft 9in

10in Single 2 26ft 2in

15in Single 2 17ft 5in 87ft 1in


22in Single 1 23ft 9in 118ft 10in30in Single 1 17ft 5in 87ft 1in




30in Twin 1 pair 17ft 5in 87ft 1in

36in Twin 1 pair 14ft 6in 72ft 7in

38in Twin 1 pair 13ft 9in 68ft 9in40in Twin 1 pair 13ft 1in 65ft 4in

* Not all spacings may be offered on implements 31442 covered by this manual.



Monitor ConfigurationIRC drive meter rate is set directly on the seed monitor inthe tractor. Consult the monitor manual for detailedinstructions, which may vary slightly over time withfirmware updates to the monitor system.

Enter/update your planter configuration (width/row-count,row pattern, disk cell count, etc.). Once entered, specifythe population directly in thousand seeds/acre orthousand seeds/ha.

Enter meter RPM limits for your disk.

For consistent results, and least meter wear, do notexceed the recommended ground speed.

For step 1 through step 4, any needed data not providedin this manual can be found in one or more of:Planter Operator Manual

Refer to the DICKEY-john® IntelliAg®Planter/Drill ControlOperator’s Manual for details on setup item.

The monitor must be in User Level 2 to change someof these parameters.

1. For a crop not previously planted with this planter,create a “Material Name” for the crop. Selecting anamed material is a required step in later screens.

2. Verify, and as needed setup or update the “Material”record for the singulated seed to be planted.

The “Material / Data Required” table lists theparameters that need to be reviewed or set. <anglebracket> values are your choice/preference when notfrom meter rpm chart.

3. Count rows individually for “# Seed Rows”. A twinpair (if both openers are in use) counts as 2 rows.“Channel Width” is swath.

4. In the Material Library screen, makes sure that theMaterial (SOYBEANS in our example) is assigned tothe Channel (CH 1 in our example) which controlsthe planter’s drive.

5. Switch the seed monitor from Setup/Configurationmode to Operate mode. Load seed. Move theplanter to the field.

Material Data Required

Material Name <crop name, such as “SOYBEANS”>Type Individual Row ControlPreset Method “Disabled” unless populations varyTarget Rate <your election>Max Rate <110% of Target> is suggestedMin Rate <90% of Target> is suggestedInc/Dec <“1.0%”> is suggestedSeeds Per Rev <seed disk cell count>Disc Low Limit <rpm from seed rate chart>Disc High Limit <rpm from seed rate chart>High Pop Alarm <“20%”> is suggestedLow Pop Alarm <“20%”> is suggestedProd Level Alarm

0

Channel - IRC Data Required

CHANNEL 1 (must be channel specified above)Type “IRC”Drive Type IRCDelay Time 0Gear Ratio: 81Twin Row: Disabled

Channel - Hydraulic Data Required

CHANNEL 1 (must be channel specified above)Type “Planter Control”Material Name (must be material specified above)Control Mode AutoDrive Type PWM 1Drive Frequency 100 HzInput Filter 50%



Material Seeding SetupGeneral Information

These instructions explain how to configure the monitorfor materials outside of the default seeding choices.

Related DocumentsThese are the current seed monitor manuals relied uponfor the user interface instructions in this section:

Prepare MetersSee planter operator manual for details on these steps.

1. Remove rain covers on all rows.

2. Perform a clean-out of the planter seed system, from hoppers to meter brushes.

3. Remove and save the presently installed seed disks.

4. Install desired seed disks.

5. Install the rain covers.

6. Set the seed inlet shutters to the recommended values in the rpm limits chart.

7. Set meter pressurization. See operator manual for adjustment details.

Loading SeedUse ample Ezee Glide Plus seed lubricant with smallseeds such as canola and mustard. One cup (240 ml)per 30 pound (13.6 kg) bag is a minimum starting value.

This setup requires password protected user level 2.

Material Setup1. Navigate to the Control Setup and then press the

Material Setup button.

2. Select an available default “MATRL” to redefine, orselect an existing named material.

3. Touch the material icon and enter desired name.

4. The population ranges and rpm limits are given bythe chart below.

To activate your new material, go to channel controls andselect material. Material will now appear on work screen.

DICKEY-john® IntelliAg®

6011258 PDC User Levels 2&3 (ver. 3)

1

Type must be IRC

Preset <user preference>

Target Rate <user preference>

Max/Min Rates <user preference>

Inc/Dec <user preference>

Seeds per Rev must be 150 for 817-991C disk



Meter RPM Limit ChartsAir-Pro® Meter RPM Limits Initial Seed Inlet Shutter Setting: 3

CORN

24 Cell Disk

mph kph acre hectare acre hectare mph kph acre hectare acre hectare4.0 6.4 71 280 176 133 23 760 58 711 4.0 6.4 38 797 95 866 12 932 31 955

4.5 7.2 63 360 156 563 21 120 52 188 4.5 7.2 34 486 85 215 11 495 28 405

Max Min 5.0 8.0 57 024 140 906 19 008 46 969 Max Min 5.0 8.0 31 037 76 693 10 346 25 564

rpm rpm 5.5 8.9 51 840 128 097 17 280 42 699 rpm rpm 5.5 8.9 28 216 69 721 09 405 23 240

30 10 6.0 9.7 47 520 117 422 15 840 39 141 30 10 6.0 9.7 25 864 63 911 08 621 21 304

6.5 10.5 43 865 108 389 14 622 36 130 6.5 10.5 23 875 58 995 07 958 19 665

4.0 6.4 59 400 146 777 19 800 48 926 4.0 6.4 35 640 88 066 11 880 29 355

4.5 7.2 52 800 130 469 17 600 43 490 4.5 7.2 31 680 78 281 10 560 26 094

Max Min 5.0 8.0 47 520 117 422 15 840 39 141 Max Min 5.0 8.0 28 512 70 453 09 504 23 484

rpm rpm 5.5 8.9 43 200 106 747 14 400 35 582 rpm rpm 5.5 8.9 25 920 64 048 08 640 21 349

30 10 6.0 9.7 39 600 97 852 13 200 32 617 30 10 6.0 9.7 23 760 58 711 07 920 19 570

6.5 10.5 36 554 90 325 12 185 30 108 6.5 10.5 21 932 54 195 07 311 18 065

4.0 6.4 56 274 139 052 18 758 46 351 4.0 6.4 29 700 73 389 09 900 24 463

4.5 7.2 50 021 123 602 16 674 41 201 4.5 7.2 26 400 65 234 08 800 21 745

Max Min 5.0 8.0 45 019 111 242 15 006 37 081 Max Min 5.0 8.0 23 760 58 711 07 920 19 570

rpm rpm 5.5 8.9 40 926 101 129 13 642 33 710 rpm rpm 5.5 8.9 21 600 53 374 07 200 17 791

30 10 6.0 9.7 37 516 92 702 12 505 30 901 30 10 6.0 9.7 19 800 48 926 06 600 16 309

6.5 10.5 34 630 85 571 11 543 28 524 6.5 10.5 18 277 45 162 06 092 15 054

4.0 6.4 53 460 132 100 17 820 44 033 4.0 6.4 28 137 69 526 09 379 23 175

4.5 7.2 47 520 117 422 15 840 39 141 4.5 7.2 25 011 61 801 08 337 20 600

Max Min 5.0 8.0 42 768 105 680 14 256 35 227 Max Min 5.0 8.0 22 509 55 621 07 503 18 540

rpm rpm 5.5 8.9 38 880 96 072 12 960 32 024 rpm rpm 5.5 8.9 20 463 50 564 06 821 16 855

30 10 6.0 9.7 35 640 88 066 11 880 29 355 30 10 6.0 9.7 18 758 46 351 06 253 15 450

6.5 10.5 32 898 81 292 10 966 27 097 6.5 10.5 17 315 42 785 05 772 14 262

4.0 6.4 48 600 120 091 16 200 40 030 4.0 6.4 26 730 66 050 08 910 22 017

4.5 7.2 43 200 106 747 14 400 35 582 4.5 7.2 23 760 58 711 07 920 19 570

Max Min 5.0 8.0 38 880 96 072 12 960 32 024 Max Min 5.0 8.0 21 384 52 840 07 128 17 613

rpm rpm 5.5 8.9 35 345 87 339 11 782 29 113 rpm rpm 5.5 8.9 19 440 48 036 06 480 16 012

30 10 6.0 9.7 32 400 80 060 10 800 26 687 30 10 6.0 9.7 17 820 44 033 05 940 14 678

6.5 10.5 29 908 73 902 09 969 24 634 6.5 10.5 16 449 40 646 05 483 13 549

817-794C Round Corn Large

837-126C Round Corn Med

817-795C Round Corn Small

817-836C Flat Corn Large

Planting Speed

Minimum Population

seeds per

Maximum Population

Minimum Population

seeds per seeds per

Twin Row 40in20in Rows 38in Rows

Twin Row 30in15in Rows

Planting Speed

Maximum Population

seeds per

70cm Rows

22in Rows 40in Rows

Twin Row 36in 30in Rows




Air-Pro® Meter RPM Limits Initial Seed Inlet Shutter Setting: 3

CORN

40 Cell Disk


4.5 7.2 105 600 260 938 35 200 86 979 4.5 7.2 57 476 142 024 19 159 47 341

Max Min 5.0 8.0 95 040 234 844 31 680 78 281 Max Min 5.0 8.0 51 729 127 822 17 243 42 607

rpm rpm 5.5 8.9 86 400 213 494 28 800 71 165 rpm rpm 5.5 8.9 47 026 116 202 15 675 38 734

30 10 6.0 9.7 79 200 195 703 26 400 65 234 30 10 6.0 9.7 43 107 106 518 14 369 35 506

6.5 10.5 73 108 180 649 24 369 60 216 6.5 10.5 39 791 98 325 13 264 32 775

4.0 6.4 99 000 244 629 33 000 81 543 4.0 6.4 59 400 146 777 19 800 48 926

4.5 7.2 88 000 217 448 29 333 72 483 4.5 7.2 52 800 130 469 17 600 43 490

Max Min 5.0 8.0 79 200 195 703 26 400 65 234 Max Min 5.0 8.0 47 520 117 422 15 840 39 141

rpm rpm 5.5 8.9 72 000 177 912 24 000 59 304 rpm rpm 5.5 8.9 43 200 106 747 14 400 35 582

30 10 6.0 9.7 66 000 163 086 22 000 54 362 30 10 6.0 9.7 39 600 97 852 13 200 32 617

6.5 10.5 60 923 150 541 20 308 50 180 6.5 10.5 36 554 90 325 12 185 30 108

4.0 6.4 93 789 231 754 31 263 77 251 4.0 6.4 49 500 122 315 16 500 40 772

4.5 7.2 83 368 206 003 27 789 68 668 4.5 7.2 44 000 108 724 14 667 36 241

Max Min 5.0 8.0 75 032 185 403 25 011 61 801 Max Min 5.0 8.0 39 600 97 852 13 200 32 617

rpm rpm 5.5 8.9 68 211 168 548 22 737 56 183 rpm rpm 5.5 8.9 36 000 88 956 12 000 29 652

30 10 6.0 9.7 62 526 154 503 20 842 51 501 30 10 6.0 9.7 33 000 81 543 11 000 27 181

6.5 10.5 57 717 142 618 19 239 47 539 6.5 10.5 30 462 75 270 10 154 25 090

4.0 6.4 89 100 220 166 29 700 73 389 4.0 6.4 46 895 115 877 15 632 38 626

4.5 7.2 79 200 195 703 26 400 65 234 4.5 7.2 41 684 103 002 13 895 34 334

Max Min 5.0 8.0 71 280 176 133 23 760 58 711 Max Min 5.0 8.0 37 516 92 702 12 505 30 901

rpm rpm 5.5 8.9 64 800 160 121 21 600 53 374 rpm rpm 5.5 8.9 34 105 84 274 11 368 28 091

30 10 6.0 9.7 59 400 146 777 19 800 48 926 30 10 6.0 9.7 31 263 77 251 10 421 25 750

6.5 10.5 54 831 135 487 18 277 45 162 6.5 10.5 28 858 71 309 09 619 23 770

4.0 6.4 81 000 200 151 27 000 66 717 4.0 6.4 44 550 110 083 14 850 36 694

4.5 7.2 72 000 177 912 24 000 59 304 4.5 7.2 39 600 97 852 13 200 32 617

Max Min 5.0 8.0 64 800 160 121 21 600 53 374 Max Min 5.0 8.0 35 640 88 066 11 880 29 355

rpm rpm 5.5 8.9 58 909 145 564 19 636 48 521 rpm rpm 5.5 8.9 32 400 80 060 10 800 26 687

30 10 6.0 9.7 54 000 133 434 18 000 44 478 30 10 6.0 9.7 29 700 73 389 09 900 24 463

6.5 10.5 49 846 123 170 16 615 41 057 6.5 10.5 27 415 67 743 09 138 22 581


22in Rows 40in Rows

Twin Row 30in15in Rows 70cm Rows



Planting Speed

Maximum Population

Minimum Population

seeds per seeds per seeds per seeds per

817-796C Round Corn Large

837-127C Round Corn Med

817-797C Round Corn Small

817-838C Flat Corn Large

Planting Speed

Maximum Population

Minimum Population




Med Edible Bean

60 Cell Disk


4.5 7.2 158 400 391 406 26 400 65 234 4.5 7.2 86 215 213 037 14 369 35 506

Max Min 5.0 8.0 142 560 352 266 23 760 58 711 Max Min 5.0 8.0 77 593 191 733 12 932 31 955

rpm rpm 5.5 8.9 129 600 320 242 21 600 53 374 rpm rpm 5.5 8.9 70 539 174 303 11 757 29 050

30 5 6.0 9.7 118 800 293 555 19 800 48 926 30 5 6.0 9.7 64 661 159 777 10 777 26 630

6.5 10.5 109 662 270 974 18 277 45 162 6.5 10.5 59 687 147 487 09 948 24 581

4.0 6.4 148 500 366 944 24 750 61 157 4.0 6.4 89 100 220 166 14 850 36 694

4.5 7.2 132 000 326 172 22 000 54 362 4.5 7.2 79 200 195 703 13 200 32 617

Max Min 5.0 8.0 118 800 293 555 19 800 48 926 Max Min 5.0 8.0 71 280 176 133 11 880 29 355

rpm rpm 5.5 8.9 108 000 266 868 18 000 44 478 rpm rpm 5.5 8.9 64 800 160 121 10 800 26 687

30 5 6.0 9.7 99 000 244 629 16 500 40 772 30 5 6.0 9.7 59 400 146 777 09 900 24 463

6.5 10.5 91 385 225 811 15 231 37 635 6.5 10.5 54 831 135 487 09 138 22 581

4.0 6.4 140 684 347 631 23 447 57 938 4.0 6.4 74 250 183 472 12 375 30 579

4.5 7.2 125 053 309 005 20 842 51 501 4.5 7.2 66 000 163 086 11 000 27 181

Max Min 5.0 8.0 112 547 278 105 18 758 46 351 Max Min 5.0 8.0 59 400 146 777 09 900 24 463

rpm rpm 5.5 8.9 102 316 252 822 17 053 42 137 rpm rpm 5.5 8.9 54 000 133 434 09 000 22 239

30 5 6.0 9.7 93 789 231 754 15 632 38 626 30 5 6.0 9.7 49 500 122 315 08 250 20 386

6.5 10.5 86 575 213 927 14 429 35 654 6.5 10.5 45 692 112 906 07 615 18 818

4.0 6.4 133 650 330 249 22 275 55 042 4.0 6.4 70 342 173 815 11 724 28 969

4.5 7.2 118 800 293 555 19 800 48 926 4.5 7.2 62 526 154 503 10 421 25 750

Max Min 5.0 8.0 106 920 264 199 17 820 44 033 Max Min 5.0 8.0 56 274 139 052 09 379 23 175

rpm rpm 5.5 8.9 97 200 240 181 16 200 40 030 rpm rpm 5.5 8.9 51 158 126 411 08 526 21 069

30 5 6.0 9.7 89 100 220 166 14 850 36 694 30 5 6.0 9.7 46 895 115 877 07 816 19 313

6.5 10.5 82 246 203 230 13 708 33 872 6.5 10.5 43 287 106 963 07 215 17 827

4.0 6.4 121 500 300 227 20 250 50 038 4.0 6.4 66 825 165 125 11 138 27 521

4.5 7.2 108 000 266 868 18 000 44 478 4.5 7.2 59 400 146 777 09 900 24 463

Max Min 5.0 8.0 97 200 240 181 16 200 40 030 Max Min 5.0 8.0 53 460 132 100 08 910 22 017

rpm rpm 5.5 8.9 88 364 218 347 14 727 36 391 rpm rpm 5.5 8.9 48 600 120 091 08 100 20 015

30 5 6.0 9.7 81 000 200 151 13 500 33 359 30 5 6.0 9.7 44 550 110 083 07 425 18 347

6.5 10.5 74 769 184 755 12 462 30 792 6.5 10.5 41 123 101 615 06 854 16 936

seeds per seeds per seeds per

Planting Speed

Maximum Population

Minimum Population


22in Rows 40in Rows

837-065C Med Edible Bean

ATTENTION: This disk is for Hopper Style Planter only. Do not use with an Air Delivery type planter.




Planting Speed

Maximum Population

Minimum Population

seeds per




Lrg Edible Bean

56 Cell Disk


4.5 7.2 147 840 365 313 24 640 60 885 4.5 7.2 80 467 198 834 13 411 33 139

Max Min 5.0 8.0 133 056 328 781 22 176 54 797 Max Min 5.0 8.0 72 420 178 951 12 070 29 825

rpm rpm 5.5 8.9 120 960 298 892 20 160 49 815 rpm rpm 5.5 8.9 65 837 162 682 10 973 27 114

30 5 6.0 9.7 110 880 273 984 18 480 45 664 30 5 6.0 9.7 60 350 149 126 10 058 24 854

6.5 10.5 102 351 252 909 17 058 42 151 6.5 10.5 55 708 137 654 09 285 22 942

4.0 6.4 138 600 342 481 23 100 57 080 4.0 6.4 83 160 205 488 13 860 34 248

4.5 7.2 123 200 304 427 20 533 50 738 4.5 7.2 73 920 182 656 12 320 30 443

Max Min 5.0 8.0 110 880 273 984 18 480 45 664 Max Min 5.0 8.0 66 528 164 391 11 088 27 398

rpm rpm 5.5 8.9 100 800 249 077 16 800 41 513 rpm rpm 5.5 8.9 60 480 149 446 10 080 24 908

30 5 6.0 9.7 92 400 228 320 15 400 38 053 30 5 6.0 9.7 55 440 136 992 09 240 22 832

6.5 10.5 85 292 210 757 14 215 35 126 6.5 10.5 51 175 126 454 08 529 21 076

4.0 6.4 131 305 324 455 21 884 54 076 4.0 6.4 69 300 171 240 11 550 28 540

4.5 7.2 116 716 288 405 19 453 48 067 4.5 7.2 61 600 152 214 10 267 25 369

Max Min 5.0 8.0 105 044 259 564 17 507 43 261 Max Min 5.0 8.0 55 440 136 992 09 240 22 832

rpm rpm 5.5 8.9 95 495 235 967 15 916 39 328 rpm rpm 5.5 8.9 50 400 124 538 08 400 20 756

30 5 6.0 9.7 87 537 216 304 14 589 36 051 30 5 6.0 9.7 46 200 114 160 07 700 19 027

6.5 10.5 80 803 199 665 13 467 33 277 6.5 10.5 42 646 105 379 07 108 17 563

4.0 6.4 124 740 308 233 20 790 51 372 4.0 6.4 65 653 162 228 10 942 27 038

4.5 7.2 110 880 273 984 18 480 45 664 4.5 7.2 58 358 144 202 09 726 24 034

Max Min 5.0 8.0 99 792 246 586 16 632 41 098 Max Min 5.0 8.0 52 522 129 782 08 754 21 630

rpm rpm 5.5 8.9 90 720 224 169 15 120 37 362 rpm rpm 5.5 8.9 47 747 117 984 07 958 19 664

30 5 6.0 9.7 83 160 205 488 13 860 34 248 30 5 6.0 9.7 43 768 108 152 07 295 18 025

6.5 10.5 76 763 189 682 12 794 31 614 6.5 10.5 40 402 99 832 06 734 16 639

4.0 6.4 113 400 280 211 18 900 46 702 4.0 6.4 62 370 154 116 10 395 25 686

4.5 7.2 100 800 249 077 16 800 41 513 4.5 7.2 55 440 136 992 09 240 22 832

Max Min 5.0 8.0 90 720 224 169 15 120 37 362 Max Min 5.0 8.0 49 896 123 293 08 316 20 549

rpm rpm 5.5 8.9 82 473 203 790 13 745 33 965 rpm rpm 5.5 8.9 45 360 112 085 07 560 18 681

30 5 6.0 9.7 75 600 186 808 12 600 31 135 30 5 6.0 9.7 41 580 102 744 06 930 17 124

6.5 10.5 69 785 172 438 11 631 28 740 6.5 10.5 38 382 94 841 06 397 15 807


22in Rows 40in Rows




817-967C Lrg Edible Bean

ATTENTION: This disk is for Hopper Style Planter only. Do not use with an Air Delivery type planter.

Planting Speed

Maximum Population

Minimum Population Planting

Speed

Maximum Population

Minimum Population





COTTON

60 Cell Disk


4.5 7.2 168 960 417 500 26 400 65 234 4.5 7.2 91 962 227 239 14 369 35 506

Max Min 5.0 8.0 152 064 375 750 23 760 58 711 Max Min 5.0 8.0 82 766 204 515 12 932 31 955

rpm rpm 5.5 8.9 138 240 341 591 21 600 53 374 rpm rpm 5.5 8.9 75 242 185 923 11 757 29 050

32 5 6.0 9.7 126 720 313 125 19 800 48 926 32 5 6.0 9.7 68 972 170 429 10 777 26 630

6.5 10.5 116 972 289 039 18 277 45 162 6.5 10.5 63 666 157 319 09 948 24 581

4.0 6.4 158 400 391 406 24 750 61 157 4.0 6.4 95 040 234 844 14 850 36 694

4.5 7.2 140 800 347 917 22 000 54 362 4.5 7.2 84 480 208 750 13 200 32 617

Max Min 5.0 8.0 126 720 313 125 19 800 48 926 Max Min 5.0 8.0 76 032 187 875 11 880 29 355

rpm rpm 5.5 8.9 115 200 284 659 18 000 44 478 rpm rpm 5.5 8.9 69 120 170 796 10 800 26 687

32 5 6.0 9.7 105 600 260 938 16 500 40 772 32 5 6.0 9.7 63 360 156 563 09 900 24 463

6.5 10.5 97 477 240 865 15 231 37 635 6.5 10.5 58 486 144 519 09 138 22 581

4.0 6.4 150 063 370 806 23 447 57 938 4.0 6.4 79 200 195 703 12 375 30 579

4.5 7.2 133 389 329 605 20 842 51 501 4.5 7.2 70 400 173 958 11 000 27 181

Max Min 5.0 8.0 120 051 296 645 18 758 46 351 Max Min 5.0 8.0 63 360 156 563 09 900 24 463

rpm rpm 5.5 8.9 109 137 269 677 17 053 42 137 rpm rpm 5.5 8.9 57 600 142 330 09 000 22 239

32 5 6.0 9.7 100 042 247 204 15 632 38 626 32 5 6.0 9.7 52 800 130 469 08 250 20 386

6.5 10.5 92 347 228 188 14 429 35 654 6.5 10.5 48 738 120 433 07 615 18 818

4.0 6.4 142 560 352 266 22 275 55 042 4.0 6.4 75 032 185 403 11 724 28 969

4.5 7.2 126 720 313 125 19 800 48 926 4.5 7.2 66 695 164 803 10 421 25 750

Max Min 5.0 8.0 114 048 281 813 17 820 44 033 Max Min 5.0 8.0 60 025 148 322 09 379 23 175

rpm rpm 5.5 8.9 103 680 256 193 16 200 40 030 rpm rpm 5.5 8.9 54 568 134 839 08 526 21 069

32 5 6.0 9.7 95 040 234 844 14 850 36 694 32 5 6.0 9.7 50 021 123 602 07 816 19 313

6.5 10.5 87 729 216 779 13 708 33 872 6.5 10.5 46 173 114 094 07 215 17 827

4.0 6.4 129 600 320 242 20 250 50 038 4.0 6.4 71 280 176 133 11 138 27 521

4.5 7.2 115 200 284 659 18 000 44 478 4.5 7.2 63 360 156 563 09 900 24 463

Max Min 5.0 8.0 103 680 256 193 16 200 40 030 Max Min 5.0 8.0 57 024 140 906 08 910 22 017

rpm rpm 5.5 8.9 94 255 232 903 14 727 36 391 rpm rpm 5.5 8.9 51 840 128 097 08 100 20 015

32 5 6.0 9.7 86 400 213 494 13 500 33 359 32 5 6.0 9.7 47 520 117 422 07 425 18 347

6.5 10.5 79 754 197 072 12 462 30 792 6.5 10.5 43 865 108 389 06 854 16 936

817-857C Cotton

Planting Speed

Maximum Population


Speed

Maximum Population

Minimum Population



22in Rows 40in Rows







MILO

30 Cell Disk


4.5 7.2 79 200 195 703 13 200 32 617 4.5 7.2 43 107 106 518 07 185 17 753

Max Min 5.0 8.0 71 280 176 133 11 880 29 355 Max Min 5.0 8.0 38 797 95 866 06 466 15 978

rpm rpm 5.5 8.9 64 800 160 121 10 800 26 687 rpm rpm 5.5 8.9 35 270 87 151 05 878 14 525

30 5 6.0 9.7 59 400 146 777 09 900 24 463 30 5 6.0 9.7 32 331 79 889 05 388 13 315

6.5 10.5 54 831 135 487 09 138 22 581 6.5 10.5 29 844 73 743 04 974 12 291

4.0 6.4 74 250 183 472 12 375 30 579 4.0 6.4 44 550 110 083 07 425 18 347

4.5 7.2 66 000 163 086 11 000 27 181 4.5 7.2 39 600 97 852 06 600 16 309

Max Min 5.0 8.0 59 400 146 777 09 900 24 463 Max Min 5.0 8.0 35 640 88 066 05 940 14 678

rpm rpm 5.5 8.9 54 000 133 434 09 000 22 239 rpm rpm 5.5 8.9 32 400 80 060 05 400 13 343

30 5 6.0 9.7 49 500 122 315 08 250 20 386 30 5 6.0 9.7 29 700 73 389 04 950 12 231

6.5 10.5 45 692 112 906 07 615 18 818 6.5 10.5 27 415 67 743 04 569 11 291

4.0 6.4 70 342 173 815 11 724 28 969 4.0 6.4 37 125 91 736 06 188 15 289

4.5 7.2 62 526 154 503 10 421 25 750 4.5 7.2 33 000 81 543 05 500 13 591

Max Min 5.0 8.0 56 274 139 052 09 379 23 175 Max Min 5.0 8.0 29 700 73 389 04 950 12 231

rpm rpm 5.5 8.9 51 158 126 411 08 526 21 069 rpm rpm 5.5 8.9 27 000 66 717 04 500 11 120

30 5 6.0 9.7 46 895 115 877 07 816 19 313 30 5 6.0 9.7 24 750 61 157 04 125 10 193

6.5 10.5 43 287 106 963 07 215 17 827 6.5 10.5 22 846 56 453 03 808 09 409

4.0 6.4 66 825 165 125 11 138 27 521 4.0 6.4 35 171 86 908 05 862 14 485

4.5 7.2 59 400 146 777 09 900 24 463 4.5 7.2 31 263 77 251 05 211 12 875

Max Min 5.0 8.0 53 460 132 100 08 910 22 017 Max Min 5.0 8.0 28 137 69 526 04 689 11 588

rpm rpm 5.5 8.9 48 600 120 091 08 100 20 015 rpm rpm 5.5 8.9 25 579 63 206 04 263 10 534

30 5 6.0 9.7 44 550 110 083 07 425 18 347 30 5 6.0 9.7 23 447 57 938 03 908 09 656

6.5 10.5 41 123 101 615 06 854 16 936 6.5 10.5 21 644 53 482 03 607 08 914

4.0 6.4 60 750 150 113 10 125 25 019 4.0 6.4 33 413 82 562 05 569 13 760

4.5 7.2 54 000 133 434 09 000 22 239 4.5 7.2 29 700 73 389 04 950 12 231

Max Min 5.0 8.0 48 600 120 091 08 100 20 015 Max Min 5.0 8.0 26 730 66 050 04 455 11 008

rpm rpm 5.5 8.9 44 182 109 173 07 364 18 196 rpm rpm 5.5 8.9 24 300 60 045 04 050 10 008

30 5 6.0 9.7 40 500 100 076 06 750 16 679 30 5 6.0 9.7 22 275 55 042 03 713 09 174

6.5 10.5 37 385 92 377 06 231 15 396 6.5 10.5 20 562 50 808 03 427 08 468


22in Rows 40in Rows




837-057C Milo

Planting Speed

Maximum Population


Speed

Maximum Population

Minimum Population





MILO

65 Cell Disk


4.5 7.2 171 600 424 024 28 600 70 671 4.5 7.2 93 399 230 790 15 567 38 465

Max Min 5.0 8.0 154 440 381 621 25 740 63 604 Max Min 5.0 8.0 84 059 207 711 14 010 34 618

rpm rpm 5.5 8.9 140 400 346 928 23 400 57 821 rpm rpm 5.5 8.9 76 418 188 828 12 736 31 471

30 5 6.0 9.7 128 700 318 018 21 450 53 003 30 5 6.0 9.7 70 049 173 092 11 675 28 849

6.5 10.5 118 800 293 555 19 800 48 926 6.5 10.5 64 661 159 777 10 777 26 630

4.0 6.4 160 875 397 522 26 813 66 254 4.0 6.4 96 525 238 513 16 088 39 752

4.5 7.2 143 000 353 353 23 833 58 892 4.5 7.2 85 800 212 012 14 300 35 335

Max Min 5.0 8.0 128 700 318 018 21 450 53 003 Max Min 5.0 8.0 77 220 190 811 12 870 31 802

rpm rpm 5.5 8.9 117 000 289 107 19 500 48 185 rpm rpm 5.5 8.9 70 200 173 464 11 700 28 911

30 5 6.0 9.7 107 250 265 015 17 875 44 169 30 5 6.0 9.7 64 350 159 009 10 725 26 501

6.5 10.5 99 000 244 629 16 500 40 772 6.5 10.5 59 400 146 777 09 900 24 463

4.0 6.4 152 408 376 600 25 401 62 767 4.0 6.4 80 438 198 761 13 406 33 127

4.5 7.2 135 474 334 755 22 579 55 793 4.5 7.2 71 500 176 677 11 917 29 446

Max Min 5.0 8.0 121 926 301 280 20 321 50 213 Max Min 5.0 8.0 64 350 159 009 10 725 26 501

rpm rpm 5.5 8.9 110 842 273 891 18 474 45 648 rpm rpm 5.5 8.9 58 500 144 554 09 750 24 092

30 5 6.0 9.7 101 605 251 067 16 934 41 844 30 5 6.0 9.7 53 625 132 507 08 938 22 085

6.5 10.5 93 789 231 754 15 632 38 626 6.5 10.5 49 500 122 315 08 250 20 386

4.0 6.4 144 788 357 770 24 131 59 628 4.0 6.4 76 204 188 300 12 701 31 383

4.5 7.2 128 700 318 018 21 450 53 003 4.5 7.2 67 737 167 378 11 289 27 896

Max Min 5.0 8.0 115 830 286 216 19 305 47 703 Max Min 5.0 8.0 60 963 150 640 10 161 25 107

rpm rpm 5.5 8.9 105 300 260 196 17 550 43 366 rpm rpm 5.5 8.9 55 421 136 945 09 237 22 824

30 5 6.0 9.7 96 525 238 513 16 088 39 752 30 5 6.0 9.7 50 803 125 533 08 467 20 922

6.5 10.5 89 100 220 166 14 850 36 694 6.5 10.5 46 895 115 877 07 816 19 313

4.0 6.4 131 625 325 245 21 938 54 208 4.0 6.4 72 394 178 885 12 066 29 814

4.5 7.2 117 000 289 107 19 500 48 185 4.5 7.2 64 350 159 009 10 725 26 501

Max Min 5.0 8.0 105 300 260 196 17 550 43 366 Max Min 5.0 8.0 57 915 143 108 09 653 23 851

rpm rpm 5.5 8.9 95 727 236 542 15 955 39 424 rpm rpm 5.5 8.9 52 650 130 098 08 775 21 683

30 5 6.0 9.7 87 750 216 830 14 625 36 138 30 5 6.0 9.7 48 263 119 257 08 044 19 876

6.5 10.5 81 000 200 151 13 500 33 359 6.5 10.5 44 550 110 083 07 425 18 347

817-849C Milo

Planting Speed

Maximum Population


Speed

Maximum Population

Minimum Population



22in Rows 40in Rows







MILO

130 Cell Disk


4.5 7.2 343 200 848 047 57 200 141 341 4.5 7.2 186 799 461 579 31 133 76 930

Max Min 5.0 8.0 308 880 763 242 51 480 127 207 Max Min 5.0 8.0 168 119 415 421 28 020 69 237

rpm rpm 5.5 8.9 280 800 693 857 46 800 115 643 rpm rpm 5.5 8.9 152 835 377 656 25 473 62 943

30 5 6.0 9.7 257 400 636 035 42 900 106 006 30 5 6.0 9.7 140 099 346 184 23 350 57 697

6.5 10.5 237 600 587 110 39 600 97 852 6.5 10.5 129 322 319 555 21 554 53 259

4.0 6.4 321 750 795 044 53 625 132 507 4.0 6.4 193 050 477 027 32 175 79 504

4.5 7.2 286 000 706 706 47 667 117 784 4.5 7.2 171 600 424 024 28 600 70 671

Max Min 5.0 8.0 257 400 636 035 42 900 106 006 Max Min 5.0 8.0 154 440 381 621 25 740 63 604

rpm rpm 5.5 8.9 234 000 578 214 39 000 96 369 rpm rpm 5.5 8.9 140 400 346 928 23 400 57 821

30 5 6.0 9.7 214 500 530 030 35 750 88 338 30 5 6.0 9.7 128 700 318 018 21 450 53 003

6.5 10.5 198 000 489 258 33 000 81 543 6.5 10.5 118 800 293 555 19 800 48 926

4.0 6.4 304 816 753 200 50 803 125 533 4.0 6.4 160 875 397 522 26 813 66 254

4.5 7.2 270 947 669 511 45 158 111 585 4.5 7.2 143 000 353 353 23 833 58 892

Max Min 5.0 8.0 243 853 602 560 40 642 100 427 Max Min 5.0 8.0 128 700 318 018 21 450 53 003

rpm rpm 5.5 8.9 221 684 547 782 36 947 91 297 rpm rpm 5.5 8.9 117 000 289 107 19 500 48 185

30 5 6.0 9.7 203 211 502 133 33 868 83 689 30 5 6.0 9.7 107 250 265 015 17 875 44 169

6.5 10.5 187 579 463 508 31 263 77 251 6.5 10.5 99 000 244 629 16 500 40 772

4.0 6.4 289 575 715 540 48 263 119 257 4.0 6.4 152 408 376 600 25 401 62 767

4.5 7.2 257 400 636 035 42 900 106 006 4.5 7.2 135 474 334 755 22 579 55 793

Max Min 5.0 8.0 231 660 572 432 38 610 95 405 Max Min 5.0 8.0 121 926 301 280 20 321 50 213

rpm rpm 5.5 8.9 210 600 520 393 35 100 86 732 rpm rpm 5.5 8.9 110 842 273 891 18 474 45 648

30 5 6.0 9.7 193 050 477 027 32 175 79 504 30 5 6.0 9.7 101 605 251 067 16 934 41 844

6.5 10.5 178 200 440 332 29 700 73 389 6.5 10.5 93 789 231 754 15 632 38 626

4.0 6.4 263 250 650 491 43 875 108 415 4.0 6.4 144 788 357 770 24 131 59 628

4.5 7.2 234 000 578 214 39 000 96 369 4.5 7.2 128 700 318 018 21 450 53 003

Max Min 5.0 8.0 210 600 520 393 35 100 86 732 Max Min 5.0 8.0 115 830 286 216 19 305 47 703

rpm rpm 5.5 8.9 191 455 473 084 31 909 78 847 rpm rpm 5.5 8.9 105 300 260 196 17 550 43 366

30 5 6.0 9.7 175 500 433 661 29 250 72 277 30 5 6.0 9.7 96 525 238 513 16 088 39 752

6.5 10.5 162 000 400 302 27 000 66 717 6.5 10.5 89 100 220 166 14 850 36 694


22in Rows 40in Rows




817-800C Milo

Planting Speed

Maximum Population


Speed

Maximum Population

Minimum Population





SOYBEAN

84 Cell Disk


4.5 7.2 273 504 675 828 36 960 91 328 4.5 7.2 148 864 367 843 20 117 49 709

Max Min 5.0 8.0 246 154 608 246 33 264 82 195 Max Min 5.0 8.0 133 978 331 059 18 105 44 738

rpm rpm 5.5 8.9 223 776 552 950 30 240 74 723 rpm rpm 5.5 8.9 121 798 300 963 16 459 40 671

37 5 6.0 9.7 205 128 506 871 27 720 68 496 37 5 6.0 9.7 111 648 275 882 15 088 37 281

6.5 10.5 189 349 467 881 25 588 63 227 6.5 10.5 103 060 254 661 13 927 34 414

4.0 6.4 256 410 633 589 34 650 85 620 4.0 6.4 153 846 380 153 20 790 51 372

4.5 7.2 227 920 563 190 30 800 76 107 4.5 7.2 136 752 337 914 18 480 45 664

Max Min 5.0 8.0 205 128 506 871 27 720 68 496 Max Min 5.0 8.0 123 077 304 123 16 632 41 098

rpm rpm 5.5 8.9 186 480 460 792 25 200 62 269 rpm rpm 5.5 8.9 111 888 276 475 15 120 37 362

37 5 6.0 9.7 170 940 422 393 23 100 57 080 37 5 6.0 9.7 102 564 253 436 13 860 34 248

6.5 10.5 157 791 389 901 21 323 52 689 6.5 10.5 94 674 233 941 12 794 31 614

4.0 6.4 242 915 600 242 32 826 81 114 4.0 6.4 128 205 316 795 17 325 42 810

4.5 7.2 215 924 533 549 29 179 72 101 4.5 7.2 113 960 281 595 15 400 38 053

Max Min 5.0 8.0 194 332 480 194 26 261 64 891 Max Min 5.0 8.0 102 564 253 436 13 860 34 248

rpm rpm 5.5 8.9 176 665 436 540 23 874 58 992 rpm rpm 5.5 8.9 93 240 230 396 12 600 31 135

37 5 6.0 9.7 161 943 400 162 21 884 54 076 37 5 6.0 9.7 85 470 211 196 11 550 28 540

6.5 10.5 149 486 369 380 20 201 49 916 6.5 10.5 78 895 194 950 10 662 26 345

4.0 6.4 230 769 570 230 31 185 77 058 4.0 6.4 121 457 300 121 16 413 40 557

4.5 7.2 205 128 506 871 27 720 68 496 4.5 7.2 107 962 266 774 14 589 36 051

Max Min 5.0 8.0 184 615 456 184 24 948 61 647 Max Min 5.0 8.0 97 166 240 097 13 131 32 446

rpm rpm 5.5 8.9 167 832 414 713 22 680 56 042 rpm rpm 5.5 8.9 88 333 218 270 11 937 29 496

37 5 6.0 9.7 153 846 380 153 20 790 51 372 37 5 6.0 9.7 80 972 200 081 10 942 27 038

6.5 10.5 142 012 350 911 19 191 47 420 6.5 10.5 74 743 184 690 10 100 24 958

4.0 6.4 209 790 518 391 28 350 70 053 4.0 6.4 115 385 285 115 15 593 38 529

4.5 7.2 186 480 460 792 25 200 62 269 4.5 7.2 102 564 253 436 13 860 34 248

Max Min 5.0 8.0 167 832 414 713 22 680 56 042 Max Min 5.0 8.0 92 308 228 092 12 474 30 823

rpm rpm 5.5 8.9 152 575 377 012 20 618 50 948 rpm rpm 5.5 8.9 83 916 207 356 11 340 28 021

37 5 6.0 9.7 139 860 345 594 18 900 46 702 37 5 6.0 9.7 76 923 190 077 10 395 25 686

6.5 10.5 129 102 319 010 17 446 43 109 6.5 10.5 71 006 175 455 09 595 23 710

817-798C Soybean

Planting Speed

Maximum Population


Speed

Maximum Population

Minimum Population



22in Rows 40in Rows







SOYBEAN

168 Cell Disk


4.5 7.2 547 008 1351 657 73 920 182 656 4.5 7.2 297 728 735 686 40 234 99 417

Max Min 5.0 8.0 492 307 1216 491 66 528 164 391 Max Min 5.0 8.0 267 955 662 118 36 210 89 475

rpm rpm 5.5 8.9 447 552 1105 901 60 480 149 446 rpm rpm 5.5 8.9 243 596 601 925 32 918 81 341

37 5 6.0 9.7 410 256 1013 743 55 440 136 992 37 5 6.0 9.7 223 296 551 765 30 175 74 563

6.5 10.5 378 698 935 762 51 175 126 454 6.5 10.5 206 119 509 321 27 854 68 827

4.0 6.4 512 820 1267 178 69 300 171 240 4.0 6.4 307 692 760 307 41 580 102 744

4.5 7.2 455 840 1126 381 61 600 152 214 4.5 7.2 273 504 675 828 36 960 91 328

Max Min 5.0 8.0 410 256 1013 743 55 440 136 992 Max Min 5.0 8.0 246 154 608 246 33 264 82 195

rpm rpm 5.5 8.9 372 960 921 584 50 400 124 538 rpm rpm 5.5 8.9 223 776 552 950 30 240 74 723

37 5 6.0 9.7 341 880 844 785 46 200 114 160 37 5 6.0 9.7 205 128 506 871 27 720 68 496

6.5 10.5 315 582 779 802 42 646 105 379 6.5 10.5 189 349 467 881 25 588 63 227

4.0 6.4 485 829 1200 485 65 653 162 228 4.0 6.4 256 410 633 589 34 650 85 620

4.5 7.2 431 848 1067 097 58 358 144 202 4.5 7.2 227 920 563 190 30 800 76 107

Max Min 5.0 8.0 388 664 960 388 52 522 129 782 Max Min 5.0 8.0 205 128 506 871 27 720 68 496

rpm rpm 5.5 8.9 353 331 873 080 47 747 117 984 rpm rpm 5.5 8.9 186 480 460 792 25 200 62 269

37 5 6.0 9.7 323 886 800 323 43 768 108 152 37 5 6.0 9.7 170 940 422 393 23 100 57 080

6.5 10.5 298 972 738 760 40 402 99 832 6.5 10.5 157 791 389 901 21 323 52 689

4.0 6.4 461 538 1140 460 62 370 154 116 4.0 6.4 242 915 600 242 32 826 81 114

4.5 7.2 410 256 1013 743 55 440 136 992 4.5 7.2 215 924 533 549 29 179 72 101

Max Min 5.0 8.0 369 230 912 368 49 896 123 293 Max Min 5.0 8.0 194 332 480 194 26 261 64 891

rpm rpm 5.5 8.9 335 664 829 426 45 360 112 085 rpm rpm 5.5 8.9 176 665 436 540 23 874 58 992

37 5 6.0 9.7 307 692 760 307 41 580 102 744 37 5 6.0 9.7 161 943 400 162 21 884 54 076

6.5 10.5 284 023 701 822 38 382 94 841 6.5 10.5 149 486 369 380 20 201 49 916

4.0 6.4 419 580 1036 782 56 700 140 106 4.0 6.4 230 769 570 230 31 185 77 058

4.5 7.2 372 960 921 584 50 400 124 538 4.5 7.2 205 128 506 871 27 720 68 496

Max Min 5.0 8.0 335 664 829 426 45 360 112 085 Max Min 5.0 8.0 184 615 456 184 24 948 61 647

rpm rpm 5.5 8.9 305 149 754 023 41 236 101 895 rpm rpm 5.5 8.9 167 832 414 713 22 680 56 042

37 5 6.0 9.7 279 720 691 188 37 800 93 404 37 5 6.0 9.7 153 846 380 153 20 790 51 372

6.5 10.5 258 203 638 020 34 892 86 219 6.5 10.5 142 012 350 911 19 191 47 420


22in Rows 40in Rows




403-551D Soybean

Planting Speed

Maximum Population


Speed

Maximum Population

Minimum Population





SUNFLOWER OIL LARGE

24 Cell Disk


4.5 7.2 63 360 156 563 21 120 52 188 4.5 7.2 34 486 85 215 11 495 28 405

Max Min 5.0 8.0 57 024 140 906 19 008 46 969 Max Min 5.0 8.0 31 037 76 693 10 346 25 564

rpm rpm 5.5 8.9 51 840 128 097 17 280 42 699 rpm rpm 5.5 8.9 28 216 69 721 09 405 23 240

30 10 6.0 9.7 47 520 117 422 15 840 39 141 30 10 6.0 9.7 25 864 63 911 08 621 21 304

6.5 10.5 43 865 108 389 14 622 36 130 6.5 10.5 23 875 58 995 07 958 19 665

4.0 6.4 59 400 146 777 19 800 48 926 4.0 6.4 35 640 88 066 11 880 29 355

4.5 7.2 52 800 130 469 17 600 43 490 4.5 7.2 31 680 78 281 10 560 26 094

Max Min 5.0 8.0 47 520 117 422 15 840 39 141 Max Min 5.0 8.0 28 512 70 453 09 504 23 484

rpm rpm 5.5 8.9 43 200 106 747 14 400 35 582 rpm rpm 5.5 8.9 25 920 64 048 08 640 21 349

30 10 6.0 9.7 39 600 97 852 13 200 32 617 30 10 6.0 9.7 23 760 58 711 07 920 19 570

6.5 10.5 36 554 90 325 12 185 30 108 6.5 10.5 21 932 54 195 07 311 18 065

4.0 6.4 56 274 139 052 18 758 46 351 4.0 6.4 29 700 73 389 09 900 24 463

4.5 7.2 50 021 123 602 16 674 41 201 4.5 7.2 26 400 65 234 08 800 21 745

Max Min 5.0 8.0 45 019 111 242 15 006 37 081 Max Min 5.0 8.0 23 760 58 711 07 920 19 570

rpm rpm 5.5 8.9 40 926 101 129 13 642 33 710 rpm rpm 5.5 8.9 21 600 53 374 07 200 17 791

30 10 6.0 9.7 37 516 92 702 12 505 30 901 30 10 6.0 9.7 19 800 48 926 06 600 16 309

6.5 10.5 34 630 85 571 11 543 28 524 6.5 10.5 18 277 45 162 06 092 15 054

4.0 6.4 53 460 132 100 17 820 44 033 4.0 6.4 28 137 69 526 09 379 23 175

4.5 7.2 47 520 117 422 15 840 39 141 4.5 7.2 25 011 61 801 08 337 20 600

Max Min 5.0 8.0 42 768 105 680 14 256 35 227 Max Min 5.0 8.0 22 509 55 621 07 503 18 540

rpm rpm 5.5 8.9 38 880 96 072 12 960 32 024 rpm rpm 5.5 8.9 20 463 50 564 06 821 16 855

30 10 6.0 9.7 35 640 88 066 11 880 29 355 30 10 6.0 9.7 18 758 46 351 06 253 15 450

6.5 10.5 32 898 81 292 10 966 27 097 6.5 10.5 17 315 42 785 05 772 14 262

4.0 6.4 48 600 120 091 16 200 40 030 4.0 6.4 26 730 66 050 08 910 22 017

4.5 7.2 43 200 106 747 14 400 35 582 4.5 7.2 23 760 58 711 07 920 19 570

Max Min 5.0 8.0 38 880 96 072 12 960 32 024 Max Min 5.0 8.0 21 384 52 840 07 128 17 613

rpm rpm 5.5 8.9 35 345 87 339 11 782 29 113 rpm rpm 5.5 8.9 19 440 48 036 06 480 16 012

30 10 6.0 9.7 32 400 80 060 10 800 26 687 30 10 6.0 9.7 17 820 44 033 05 940 14 678

6.5 10.5 29 908 73 902 09 969 24 634 6.5 10.5 16 449 40 646 05 483 13 549

817-851C Sunflower Oil Large

Planting Speed

Maximum Population


Speed

Maximum Population

Minimum Population



22in Rows 40in Rows







SUNFLOWER OIL SML / MED

60 Cell Disk


4.5 7.2 158 400 391 406 52 800 130 469 4.5 7.2 86 215 213 037 28 738 71 012

Max Min 5.0 8.0 142 560 352 266 47 520 117 422 Max Min 5.0 8.0 77 593 191 733 25 864 63 911

rpm rpm 5.5 8.9 129 600 320 242 43 200 106 747 rpm rpm 5.5 8.9 70 539 174 303 23 513 58 101

30 10 6.0 9.7 118 800 293 555 39 600 97 852 30 10 6.0 9.7 64 661 159 777 21 554 53 259

6.5 10.5 109 662 270 974 36 554 90 325 6.5 10.5 59 687 147 487 19 896 49 162

4.0 6.4 148 500 366 944 49 500 122 315 4.0 6.4 89 100 220 166 29 700 73 389

4.5 7.2 132 000 326 172 44 000 108 724 4.5 7.2 79 200 195 703 26 400 65 234

Max Min 5.0 8.0 118 800 293 555 39 600 97 852 Max Min 5.0 8.0 71 280 176 133 23 760 58 711

rpm rpm 5.5 8.9 108 000 266 868 36 000 88 956 rpm rpm 5.5 8.9 64 800 160 121 21 600 53 374

30 10 6.0 9.7 99 000 244 629 33 000 81 543 30 10 6.0 9.7 59 400 146 777 19 800 48 926

6.5 10.5 91 385 225 811 30 462 75 270 6.5 10.5 54 831 135 487 18 277 45 162

4.0 6.4 140 684 347 631 46 895 115 877 4.0 6.4 74 250 183 472 24 750 61 157

4.5 7.2 125 053 309 005 41 684 103 002 4.5 7.2 66 000 163 086 22 000 54 362

Max Min 5.0 8.0 112 547 278 105 37 516 92 702 Max Min 5.0 8.0 59 400 146 777 19 800 48 926

rpm rpm 5.5 8.9 102 316 252 822 34 105 84 274 rpm rpm 5.5 8.9 54 000 133 434 18 000 44 478

30 10 6.0 9.7 93 789 231 754 31 263 77 251 30 10 6.0 9.7 49 500 122 315 16 500 40 772

6.5 10.5 86 575 213 927 28 858 71 309 6.5 10.5 45 692 112 906 15 231 37 635

4.0 6.4 133 650 330 249 44 550 110 083 4.0 6.4 70 342 173 815 23 447 57 938

4.5 7.2 118 800 293 555 39 600 97 852 4.5 7.2 62 526 154 503 20 842 51 501

Max Min 5.0 8.0 106 920 264 199 35 640 88 066 Max Min 5.0 8.0 56 274 139 052 18 758 46 351

rpm rpm 5.5 8.9 97 200 240 181 32 400 80 060 rpm rpm 5.5 8.9 51 158 126 411 17 053 42 137

30 10 6.0 9.7 89 100 220 166 29 700 73 389 30 10 6.0 9.7 46 895 115 877 15 632 38 626

6.5 10.5 82 246 203 230 27 415 67 743 6.5 10.5 43 287 106 963 14 429 35 654

4.0 6.4 121 500 300 227 40 500 100 076 4.0 6.4 66 825 165 125 22 275 55 042

4.5 7.2 108 000 266 868 36 000 88 956 4.5 7.2 59 400 146 777 19 800 48 926

Max Min 5.0 8.0 97 200 240 181 32 400 80 060 Max Min 5.0 8.0 53 460 132 100 17 820 44 033

rpm rpm 5.5 8.9 88 364 218 347 29 455 72 782 rpm rpm 5.5 8.9 48 600 120 091 16 200 40 030

30 10 6.0 9.7 81 000 200 151 27 000 66 717 30 10 6.0 9.7 44 550 110 083 14 850 36 694

6.5 10.5 74 769 184 755 24 923 61 585 6.5 10.5 41 123 101 615 13 708 33 872


22in Rows 40in Rows




837-234C Sunflower Oil Small837-235C Sunflower Oil Medium

Planting Speed

Maximum Population


Speed

Maximum Population

Minimum Population




Air-Pro® Meter RPM Limits Initial Seed Inlet Shutter Setting: 1.5

CANOLA

150 Cell Disk


4.5 7.2 330 000 815 430 66 000 163 086 4.5 7.2 179 614 443 826 35 923 88 765

Max Min 5.0 8.0 297 000 733 887 59 400 146 777 Max Min 5.0 8.0 161 653 399 444 32 331 79 889

rpm rpm 5.5 8.9 270 000 667 170 54 000 133 434 rpm rpm 5.5 8.9 146 957 363 131 29 391 72 626

30 10 6.0 9.7 247 500 611 573 49 500 122 315 30 10 6.0 9.7 134 710 332 870 26 942 66 574

6.5 10.5 228 462 564 528 45 692 112 906 6.5 10.5 124 348 307 264 24 870 61 453

4.0 6.4 309 375 764 466 61 875 152 893 4.0 6.4 185 625 458 679 37 125 91 736

4.5 7.2 275 000 679 525 55 000 135 905 4.5 7.2 165 000 407 715 33 000 81 543

Max Min 5.0 8.0 247 500 611 573 49 500 122 315 Max Min 5.0 8.0 148 500 366 944 29 700 73 389

rpm rpm 5.5 8.9 225 000 555 975 45 000 111 195 rpm rpm 5.5 8.9 135 000 333 585 27 000 66 717

30 10 6.0 9.7 206 250 509 644 41 250 101 929 30 10 6.0 9.7 123 750 305 786 24 750 61 157

6.5 10.5 190 385 470 440 38 077 94 088 6.5 10.5 114 231 282 264 22 846 56 453

4.0 6.4 293 092 724 231 58 618 144 846 4.0 6.4 154 688 382 233 30 938 76 447

4.5 7.2 260 526 643 761 52 105 128 752 4.5 7.2 137 500 339 763 27 500 67 953

Max Min 5.0 8.0 234 474 579 384 46 895 115 877 Max Min 5.0 8.0 123 750 305 786 24 750 61 157

rpm rpm 5.5 8.9 213 158 526 713 42 632 105 343 rpm rpm 5.5 8.9 112 500 277 988 22 500 55 598

30 10 6.0 9.7 195 395 482 820 39 079 96 564 30 10 6.0 9.7 103 125 254 822 20 625 50 964

6.5 10.5 180 364 445 680 36 073 89 136 6.5 10.5 95 192 235 220 19 038 47 044

4.0 6.4 278 438 688 019 55 688 137 604 4.0 6.4 146 546 362 115 29 309 72 423

4.5 7.2 247 500 611 573 49 500 122 315 4.5 7.2 130 263 321 880 26 053 64 376

Max Min 5.0 8.0 222 750 550 415 44 550 110 083 Max Min 5.0 8.0 117 237 289 692 23 447 57 938

rpm rpm 5.5 8.9 202 500 500 378 40 500 100 076 rpm rpm 5.5 8.9 106 579 263 357 21 316 52 671

30 10 6.0 9.7 185 625 458 679 37 125 91 736 30 10 6.0 9.7 97 697 241 410 19 539 48 282

6.5 10.5 171 346 423 396 34 269 84 679 6.5 10.5 90 182 222 840 18 036 44 568

4.0 6.4 253 125 625 472 50 625 125 094 4.0 6.4 139 219 344 010 27 844 68 802

4.5 7.2 225 000 555 975 45 000 111 195 4.5 7.2 123 750 305 786 24 750 61 157

Max Min 5.0 8.0 202 500 500 378 40 500 100 076 Max Min 5.0 8.0 111 375 275 208 22 275 55 042

rpm rpm 5.5 8.9 184 091 454 889 36 818 90 978 rpm rpm 5.5 8.9 101 250 250 189 20 250 50 038

30 10 6.0 9.7 168 750 416 981 33 750 83 396 30 10 6.0 9.7 92 813 229 340 18 563 45 868

6.5 10.5 155 769 384 906 31 154 76 981 6.5 10.5 85 673 211 698 17 135 42 340

837-148C Canola

Planting Speed

Maximum Population


Speed

Maximum Population

Minimum Population



22in Rows 40in Rows






Air-Pro® Meter RPM Limits Initial Seed Inlet Shutter Setting: 1.5

CANOLA

250 Cell Disk


4.5 7.2 550 000 1359 050 110 000 271 810 4.5 7.2 299 357 739 710 59 871 147 942

Max Min 5.0 8.0 495 000 1223 145 99 000 244 629 Max Min 5.0 8.0 269 421 665 739 53 884 133 148

rpm rpm 5.5 8.9 450 000 1111 950 90 000 222 390 rpm rpm 5.5 8.9 244 928 605 218 48 986 121 044

30 10 6.0 9.7 412 500 1019 288 82 500 203 858 30 10 6.0 9.7 224 517 554 783 44 903 110 957

6.5 10.5 380 769 940 881 76 154 188 176 6.5 10.5 207 247 512 107 41 449 102 421

4.0 6.4 515 625 1274 109 103 125 254 822 4.0 6.4 309 375 764 466 61 875 152 893

4.5 7.2 458 333 1132 542 91 667 226 508 4.5 7.2 275 000 679 525 55 000 135 905

Max Min 5.0 8.0 412 500 1019 288 82 500 203 858 Max Min 5.0 8.0 247 500 611 573 49 500 122 315

rpm rpm 5.5 8.9 375 000 926 625 75 000 185 325 rpm rpm 5.5 8.9 225 000 555 975 45 000 111 195

30 10 6.0 9.7 343 750 849 406 68 750 169 881 30 10 6.0 9.7 206 250 509 644 41 250 101 929

6.5 10.5 317 308 784 067 63 462 156 813 6.5 10.5 190 385 470 440 38 077 94 088

4.0 6.4 488 487 1207 051 97 697 241 410 4.0 6.4 257 813 637 055 51 563 127 411

4.5 7.2 434 211 1072 934 86 842 214 587 4.5 7.2 229 167 566 271 45 833 113 254

Max Min 5.0 8.0 390 789 965 641 78 158 193 128 Max Min 5.0 8.0 206 250 509 644 41 250 101 929

rpm rpm 5.5 8.9 355 263 877 855 71 053 175 571 rpm rpm 5.5 8.9 187 500 463 313 37 500 92 663

30 10 6.0 9.7 325 658 804 701 65 132 160 940 30 10 6.0 9.7 171 875 424 703 34 375 84 941

6.5 10.5 300 607 742 801 60 121 148 560 6.5 10.5 158 654 392 034 31 731 78 407

4.0 6.4 464 063 1146 698 92 813 229 340 4.0 6.4 244 243 603 525 48 849 120 705

4.5 7.2 412 500 1019 288 82 500 203 858 4.5 7.2 217 105 536 467 43 421 107 293

Max Min 5.0 8.0 371 250 917 359 74 250 183 472 Max Min 5.0 8.0 195 395 482 820 39 079 96 564

rpm rpm 5.5 8.9 337 500 833 963 67 500 166 793 rpm rpm 5.5 8.9 177 632 438 928 35 526 87 786

30 10 6.0 9.7 309 375 764 466 61 875 152 893 30 10 6.0 9.7 162 829 402 350 32 566 80 470

6.5 10.5 285 577 705 661 57 115 141 132 6.5 10.5 150 304 371 400 30 061 74 280

4.0 6.4 421 875 1042 453 84 375 208 491 4.0 6.4 232 031 573 349 46 406 114 670

4.5 7.2 375 000 926 625 75 000 185 325 4.5 7.2 206 250 509 644 41 250 101 929

Max Min 5.0 8.0 337 500 833 963 67 500 166 793 Max Min 5.0 8.0 185 625 458 679 37 125 91 736

rpm rpm 5.5 8.9 306 818 758 148 61 364 151 630 rpm rpm 5.5 8.9 168 750 416 981 33 750 83 396

30 10 6.0 9.7 281 250 694 969 56 250 138 994 30 10 6.0 9.7 154 688 382 233 30 938 76 447

6.5 10.5 259 615 641 510 51 923 128 302 6.5 10.5 142 788 352 830 28 558 70 566


22in Rows 40in Rows




817-991C Canola

Planting Speed

Maximum Population


Speed

Maximum Population

Minimum Population





HILL DROP COTTON

12 Cell Disk

3 seeds per hill

hill / acre sds / acre hill / acre sds / acre hill / acre sds / acre hill / acre sds / acre53 460 160 380 23 760 71 280 29 097 87 292 12 932 38 797

47 520 142 560 21 120 63 360 25 864 77 593 11 495 34 486

Max Min 42 768 128 304 19 008 57 024 Max Min 23 278 69 834 10 346 31 037

rpm rpm 38 880 116 640 17 280 51 840 rpm rpm 21 162 63 485 09 405 28 216

45 20 35 640 106 920 15 840 47 520 45 20 19 398 58 195 08 621 25 864

32 898 98 695 14 622 43 865 17 906 53 718 07 958 23 875

44 550 133 650 19 800 59 400 26 730 80 190 11 880 35 640

39 600 118 800 17 600 52 800 23 760 71 280 10 560 31 680

Max Min 35 640 106 920 15 840 47 520 Max Min 21 384 64 152 09 504 28 512

rpm rpm 32 400 97 200 14 400 43 200 rpm rpm 19 440 58 320 08 640 25 920

45 20 29 700 89 100 13 200 39 600 45 20 17 820 53 460 07 920 23 760

27 415 82 246 12 185 36 554 16 449 49 348 07 311 21 932

42 205 126 616 18 758 56 274 22 275 66 825 09 900 29 700

37 516 112 547 16 674 50 021 19 800 59 400 08 800 26 400

Max Min 33 764 101 293 15 006 45 019 Max Min 17 820 53 460 07 920 23 760

rpm rpm 30 695 92 084 13 642 40 926 rpm rpm 16 200 48 600 07 200 21 600

45 20 28 137 84 411 12 505 37 516 45 20 14 850 44 550 06 600 19 800

25 972 77 917 11 543 34 630 13 708 41 123 06 092 18 277

40 095 120 285 17 820 53 460 21 103 63 308 09 379 28 137

35 640 106 920 15 840 47 520 18 758 56 274 08 337 25 011

Max Min 32 076 96 228 14 256 42 768 Max Min 16 882 50 646 07 503 22 509

rpm rpm 29 160 87 480 12 960 38 880 rpm rpm 15 347 46 042 06 821 20 463

45 20 26 730 80 190 11 880 35 640 45 20 14 068 42 205 06 253 18 758

24 674 74 022 10 966 32 898 12 986 38 959 05 772 17 315

36 450 109 350 16 200 48 600 20 048 60 143 08 910 26 730

32 400 97 200 14 400 43 200 17 820 53 460 07 920 23 760

Max Min 29 160 87 480 12 960 38 880 Max Min 16 038 48 114 07 128 21 384

rpm rpm 26 509 79 527 11 782 35 345 rpm rpm 14 580 43 740 06 480 19 440

45 20 24 300 72 900 10 800 32 400 45 20 13 365 40 095 05 940 17 820

22 431 67 292 09 969 29 908 12 337 37 011 05 483 16 449

837-186C 3 SEEDHILLDROP COTTON

Planting Speed

Maximum Population


Speed

Maximum Population

Minimum Population




mph4.0

4.5

5.0



22in Rows 40in Rows

4.0

4.5

5.0

5.5

6.5

5.5

6.0

6.5

mph4.0

4.5

5.0

5.5

6.0

6.5

4.0

4.5

5.0

5.5

6.0

5.5

6.0

6.5

4.0

4.5

5.0

5.5 5.5

6.0

6.5

6.0

6.5

4.0

4.5

5.0

5.5

6.0

6.5

6.0

6.5

4.0

4.5

5.0

6.0

6.5

4.0

4.5

5.0

6.5

4.0

4.5

5.0

5.5

4.0

4.5

5.0

5.5

6.0


WSMT3 (Version 3) Planters Table of Contents Dry Fertilizer

Dry Fertilizer

The dry fertilizer option is driven by a ground contactwheel and fertilizer rate is independent of seed rate.Fertilizer rate is set by adjusting sprocket configurationson the fertilizer ground drive assembly.

Dry Fertilizer Rate Adjustment Make field checks to assure you are applying

fertilizer at the desired rate. Fertilizer applicationrates can vary from the weights in the charts.

Use the following steps to adjust the rate at which yourmachine applies fertilizer.

1. Adjust for the fertilizer density.

2. Consult the fertilizer rate charts.

3. Install the driving and driven sprockets called out inthe chart.

Fertilizer Density AdjustmentThe fertilizer meter rate charts are based on fertilizer witha density of 65lb/ft3 (1.04 kg/liter). If you are applyingfertilizer of a different density, use the following chart toconvert application rate.

Use the charts’ rates to determine the initial sprocketsettings. If the rate measured in calibration varies fromthe desired field rate by more than a few percent, applythe error percentage to the chart’s rate, and pick a newsprocket pairing based on that.

Dry Fertilizer Rate ChartsPL5500 - 70cm Rows

Approximate rate in pounds per acre

Approximate rate in kilograms per hectare

PL5500 - 75cm (30in) Rows

Approximate rate in pounds per acre

Approximate rate in kilograms per hectare

Density lb/ft3

(kg/liter)45

(0.72)50

(0.80)55

(0.88)60

(0.96)65

(1.04)70

(1.12)75

(1.20)80

(1.28)

Conversion Factor 1.45 1.30 1.20 1.10 1.00 0.93 0.87 0.81

Sprocket Setup

Driving

17 19 23 24 25 26 27 28

Dri

ven

17 195 236 246 256 266 277 287

19 156 211 220 229 238 247 257

23 129 144 174 182 189 197 204 212

24 123 138 167 181 189 196 203

25 118 132 160 167 181 188 195

26 114 127 154 161 167 181 188

27 110 123 148 155 161 168 181

28 106 118 143 149 156 162 168

Sprocket Setup

Driving

17 19 23 24 25 26 27 28

Dri

ven

17 218 264 276 287 299 310 322

19 175 236 247 257 267 277 288

23 144 161 195 204 212 221 229 238

24 138 155 187 203 211 220 228

25 133 148 180 187 203 211 219

26 128 143 173 180 188 203 210

27 123 137 166 174 181 188 202

28 119 132 160 167 174 181 188

Sprocket Setup

Driving

17 19 23 24 25 26 27 28D

rive

n

17 182 220 229 239 249 258 268

19 145 197 205 214 222 231 240

23 120 134 163 170 177 184 191 198

24 115 129 156 169 176 183 190

25 111 124 150 156 169 176 182

26 106 119 144 150 156 169 175

27 102 114 138 144 151 157 169

28 99 110 134 139 145 151 157

Sprocket Setup

Driving

17 19 23 24 25 26 27 28

Dri

ven

17 204 246 257 268 279 289 300

19 163 221 230 240 249 259 268

23 135 151 182 190 198 206 214 222

24 129 144 175 190 197 205 213

25 124 138 168 175 189 197 204

26 119 133 161 168 175 189 196

27 115 128 155 162 169 175 189

28 111 124 150 156 163 169 176


WSMT3 (Version 3) Planters Table of Contents Liquid Fertilizer

Liquid Fertilizer

The liquid fertilizer option uses a CDS-John Blue® pistonpump or Ace Hydraulic. For pump operation and pumpmaintenance refer to the Planter Operator manual andCDS-John Blue® pump manual. The CDS-John Blue®

manual is supplied in the liquid fertilizer option package.

The pump is driven by a ground contact wheel, andfertilizer rate is independent of seed rate. Fertilizer rate isset by a pump dial and a sprocket on the ground driveassembly.

Great Plains recommends checking with your localAgronomist as soil conditions vary. Soil conditions inyour area may need lesser or more amounts offertilizer than represented in these charts. Do notexceed 12 gallons/acre (112 liters/ha) in any case.

Always remove pump drive chain when not in use.Do not operate planter pump when not applyingmaterial.

Orifice Size Does Not Control Rate:Orifice size is only used to create 15-to-65 psi back pressure toprovide even flow between rows. Set application rate ingallons per acre using pump drive chart.

Orifice Plate SelectionIn general, the orifice needs to be small enough to createat least 15 psi of pressure in the manifold but largeenough to prevent the manifold pressure from exceeding85 psi.

The minimum pressure is required to even out the flow offertilizer between rows. To reduce orifice plugging andpump wear, use the largest orifice practical for yourfertilizer application rate.

The best pressure range to maintain is 15-to-40 psi toensure optimum distribution while minimizing leakage.

Rate Ranges vs. Orifice Size

Orifice Part Port PortSize Number Diameter Area20 832-052C 0.020 in 0.20 mm²28* 832-056C 0.028 in 0.40 mm²34* 832-053C 0.034 in 0.59 mm²48* 832-054C 0.048 in 1.17 mm²59 832-057C 0.059 in 1.76 mm²80 832-055C 0.080 in 3.24 mm²98 832-059C 0.098 in 4.87 mm²

29993* Sizes standard in many fertilizer bundles. Check your accessories before ordering.

Orifice Plate Size 20 28* 34* 48* 59 80 98Recommended Rate Range in Gallons per Acre. Range is 15 - 40 PSI

Nozzle Spacing (Values based on: 5.0 mph, 10.7 lbs/gallon Fertilizer solution density)6 inch single 5.6 - 9.1 11 - 17 16 - 26 31 - 50 46 - 76 85 - 139 134 - 2197.5 inch single 4.5 - 7.3 8.4 - 14 13 - 21 25 - 40 37 - 61 68 - 111 107 - 1758 inch single 4.2 - 6.8 7.9 - 13 12 - 19 23 - 38 35 - 57 64 - 104 101 - 1649.5 inch single 3.5 - 5.8 6.6 - 11 10 - 16 19 - 32 29 - 48 54 - 88 85 - 13810 inch single 3.4 - 5.5 6.3 - 10 9.5 - 15 18 - 30 28 - 46 51 - 83 80 - 13113.8in (35cm, 70TR) 2.4 - 4.0 4.6 - 7.5 6.9 - 11 13 - 22 20 - 33 37 - 61 58 - 9514.8in (38cm, 75TR) 2.3 - 3.7 4.3 - 7.0 6.4 - 10 12 - 20 19 - 31 35 - 56 55 - 8915in single (30TR) 2.2 - 3.6 4.2 - 6.9 6.3 - 10 12 - 20 19 - 30 34 - 56 54 - 8818in (36in Twin Row) 1.9 - 3.0 3.5 - 5.7 5.3 - 8.6 10 - 17 15 - 25 28 - 46 45 - 7319in (38in Twin Row) 1.8 - 2.9 3.3 - 5.4 5.0 - 8.1 9.7 - 16 15 - 24 27 - 44 42 - 6920 inch single 1.7 - 2.7 3.2 - 5.2 4.7 - 7.7 9.2 - 15 14 - 23 26 - 42 40 - 6627.6in (70cm single) 1.2 - 2.0 2.3 - 3.7 3.4 - 5.6 6.7 - 11 10 - 17 19 - 30 29 - 4829.5in (75cm single) 1.1 - 1.9 2.1 - 3.5 3.2 - 5.2 6.2 - 10 9 - 15 17 - 28 27 - 4530 inch single 1.1 - 1.8 2.1 - 3.4 3.2 - 5.2 6.1 - 10 9.3 - 15 17 - 28 27 - 4436 inch single 0.9 - 1.5 1.8 - 2.9 2.6 - 4.3 5.1 - 8.4 7.7 - 13 14 - 23 22 - 3738 inch single 0.9 - 1.4 1.7 - 2.7 2.5 - 4.1 4.8 - 7.9 7.3 - 12 13 - 22 21 - 3540 inch single 0.8 - 1.4 1.6 - 2.6 2.4 - 3.9 4.6 - 7.5 7.0 - 11 13 - 21 20 - 33* These sizes standard in most Great Plains fertilizer systems. 31014



Hydraulic Drive Fertilizer RateRefer to DICKEY-john IntelliAg PDC User 2 & 3 Manualto complete set up and run through Valve and K-Factorcalibrations.

Ground Drive Fertilizer Rate

Coarse rate is set by a single “driving” sprocket on theground drive assembly. Fine rate is set on a dial (settinghub) at the pump , using a tool supplied with the pump.

Material Loss / Pump Damage Risks:Disconnect chain or remove sprocket when not intending to apply material. Contact wheel and chain system operate whenever the planter is lowered and in motion. If planting without fertilizing, the pump must not be allowed to run dry.

Rate settings may be established in any of three ways:

• the table on the next page,

• the slide chart provided with the pump, or;

• a calculator on the CDS-John Blue® web site(www.cds-johnblue.com)

1. Check plumbing setup. See “Setting Relief Valve”and “Strainer” in the Operator Manual.

2. Determine Driving sprocket (15T or 47T) required fromtable, slide chart or web calculator. If this sprocket isalready installed on driven shaft, skip to step 6.Otherwise, to change sprocket, continue with step 3.

3. Loosen idler , and remove chain from lowerjackshaft .

4. Select the new sprocket from the storage shaft .Remove the pins, and exchange sprockets. Store theprevious sprocket on the storage shaft.

5. Remount the chain . Re-engage idler , tighteningso that the longest span of the chain has 1/4 inch (6 mm) of slack.

6. Use the box-wrench end of the JohnBlue 115681-01tool, and loosen the setting pointer nut .

7. Use the other end of the tool to rotate the dial tothe setting determined by table, slide chart or web.

8. Re-tighten pointer nut.

1

3

4

2

5

1

2 3

4 5

1

8

5 4

6

2

2

6


http://www.cds-johnblue.com/flow-rate-calculator.shtml


Orifice PlateThe orifice needs to be small enough to create enoughpressure in the manifold to operate the check valves, but notso much that the system dumps product at the relief valve.

The recommend operating pressure is 15 to 40 psi.

Using an orifice size too large can result in unequal flowat rows, intermittent flow, and flow stoppage at rowswhere pressure falls below the 8 psi required to open theclamp check valve. Using a size too small can causeexcess back-pressure resulting in material dumping atthe relief valve.

Use the same size at all active rows.

Agricultural Chemical Hazard:Wear protective gloves when changing orifice plates andstrainer screens. Consult material manufacturer or supplierdocuments for proper handling and steps to take if skin contactoccurs.

To install the orifice plates:

1. Remove the nozzle cap (1).

2. Remove the orifice (2) and replace with the desiredsize orifice.

Slide Chart - Liquid Fertilizer RateThe CDS-John Blue LM-1255 pump includes a slidechart for calculating pump settings.

To make the scales on this chart easier to use, this pageprovides adjusted data values. These adjusted valuesproduce results within 0.5% of the actual sprocketcombinations and loaded radius values.

Determine your desired application rate in gallons peracre. If you need to set metric rates, use theCDS-John Blue web calculator.

On the slide chart:

1. Move the upper sliding scale to align the “StandardSprocket Combinations” 24 to 50 or 16 to 60 with thecorresponding LOADED RADIUS 30 or 10,respectively. Ignore the “Sprocket Ratio” scale.

NOTE:The actual LOADED RADIUS of the ground drivewheel is 11.8 inch, which is difficult to read on thechart. The actual net SPROCKET RATIO for lowrange is 1.33, which is off-scale on the chart. Theactual net ratio for high range is 4.18, which isdifficult to match up with 11.8.

2. Use the lower sliding scale to align swath width ofyour planter under the arrow. To determine yourplanter’s swath width, multiply the machine’s rowspacing distance by the number of rows. If you areunsure of either your machine’s row spacing or rowcount, then refer to your operator manual for moreinformation.

3. Use the “LM-1255 Pump” scale to find your desiredapplication rate. Ignore the “L-4600 Pump” scale.

Inputing this information into the slide chart will provideyou with a pump setting for your desired rate.

Equipment Damage Risk:Plant at or below 8 mph (13 km/h) with the 47T Drivingsprocket installed. The pump is rated for 450 rpm maximum,which is exceeded at and above 9 mph (14 km/h).

68607

1 2

29981



Charts - Liquid Fertilizer RateThese charts show pre-computed application rates foreach half step of pump setting. If a rate shown issufficiently close to your desired field rate, use thetransmission sprocket and pump setting values toconfigure your planter.

If you need to set metric rates, use the CDS-John Blueweb calculator (see page 127).

If using the slide chart or web methods to set your rate,use the charts to quickly determine whether you needthe Low or High Range transmission sprocket paring.

Equipment Damage Risk:Plant at or below 8.8 mph (14 kph) with the standard high ratesprockets installed. The pump is rated for 550 rpm maximum,which is exceeded at and above 8.9 mph.

Model(s) Model(s)

Range Low High Range Low High

Sprockets 15T Driving 15T Driven

47T Driving 15T Driven Sprockets 15T Driving - 15T

Driven47T Driving - 15T

Driven

Ground Speed More than 2 mph Between 2 - 9.3 mph Ground

Speed More than 3.2 kph Between 3.2 - 15 kph

Pump Setting

Pump Setting

1.5 3.0 8.5 1.5 28.6 81.02.0 4.0 11.4 2.0 38.1 107.92.5 5.0 14.2 2.5 47.6 134.93.0 6.0 17.0 3.0 57.1 161.93.5 7.0 19.9 3.5 66.7 188.94.0 8.0 22.7 4.0 76.2 215.94.5 9.0 25.6 4.5 85.7 242.95.0 10.0 28.4 5.0 95.2 269.95.5 11.0 31.2 5.5 104.8 296.86.0 12.0 34.1 6.0 114.3 323.86.5 13.0 36.9 6.5 123.8 350.87.0 14.0 39.8 7.0 133.3 377.87.5 15.0 42.6 7.5 142.9 404.88.0 16.0 45.5 8.0 152.4 431.88.5 17.0 48.3 8.5 161.9 458.89.0 18.0 51.1 9.0 171.4 485.89.5 19.0 54.0 9.5 181.0 512.7

10.0 20.1 56.8 10.0 190.5 539.7

Fertilizer Rates - 17 Foot Working WidthPL5500

Application Rate (Gallons/Acre)

Fertilizer Rates - 5.2 Meter Working WidthPL5500

Application Rate (Liters/Hectare)



Setting Relief ValveA relief valve is plumbed after the pump outlet to protectthe manifold and pump from excessive pressure. Anyproduct that dumps over the relief valve will dischargefrom the dump line .

To set relief valve:

Refer to Figure 181. Unlock plastic jam nut from relief valve knob .

2. Unscrew knob clockwise until it loses contact withinternal spring.

3. Screw knob counterclockwise two turns. Start at thissetting.

4. Observe manifold gauge . Watch for relief valvedischarge while operating in the field.

5. If valve is dumping product and gauge reads under65 psi, stop tractor and turn knob clockwise (lookingdown) 1/4 turn. Continue operating at normal fieldspeed. Repeat this step as needed until no productis discharged from relief valve.

6. If pressure gauge reads above 65 psi, change to alarger orifice. Go to step 2. Repeat steps.

StrainerRefer to Figure 3A Banjo brand strainer is supplied with the fertilizer pumpoption. It is plumbed before the pump. The standard80 mesh screen should be suitable for mostapplications. Other screen sizes are available from BanjoCorporation.

Agricultural Chemical Hazard:Wear protective gloves when changing screens.

If changing screen sizes, keep in mind the following.

• A smaller mesh (100) will keep very small manifold orifice plates from plugging so often. However, the screen will have to be cleaned more often.

• A larger mesh (50) or (30) will pass more material but should only be considered when using large manifold orifice plates.

• A plugged or partially plugged screen will starve the pump resulting in a reduced application rate.

• Mesh sizes: (Smallest) 100, 80, 50, 30 (Largest)

1

2

3

4

5

31017

Figure 2Relief Valve

18418

1

2 3

41

Figure 3Strainer

18418

5

5


WSMT3 (Version 3) Planters Table of Contents Seed Lubricants

Seed Lubricants

Seed Lubricants

Air-Pro® Meters (all seeds)Ezee Glide Plus Talc+Graphite Mix

Ezee Glide Plus LubricantTo maximize performance of Great Plains metering systems,it is imperative to use only “Ezee Glide Plus” lubricant. “EzeeGlide Plus” Talc-Graphite lubricant is mandatory for all seeds,especially treated or inoculated seed. Thorough mixing ofseed and added lubricant is required.

Recommended usage:

For clean seeds other than milo, cotton, and sunflowerssprinkle one cup of Ezee Glide Plus Talc per 4 bushels orunits (170 ml per 100 liters) of seed.

For milo, cotton, and sunflowers double the application toone cup (or more) per 2 bushels or units (335 ml per100 liters) of seed.

For canola or mustard, 1 cup (240 ml) per 30 pound(13.6 kg) bag is a minimum starting value. Mix the seedlubricant early during the seed loading. Use morelubricant in extremely dry conditions.

Adjust this rate as necessary so all seeds becomecoated while avoiding an accumulation of lubricant in thebottom of the hopper.

For seed with excessive treatment, or for humid plantingenvironments, increase the rate as needed for smoothmeter operation.

Irritation and Chronic Exposure Hazard:Wear gloves. DO NOT use hands or any part of your body to mix seed lubricant. Wear a respirator when transferring and mixing. Avoid breathing lubricant dust. Not an acute hazard. May cause mechanical eye or skin irritation in high concentrations. As with all mineral spills, minimize dusting during clean-up. Prolonged inhalation may cause lung injury. Product can become slippery when wet.

Furrow Check - MetricFor furrow sample lengths in U.S. customary units, seepage 11.

821-069C bucket, 5 gallon (19 liter)

Rows to Sample Row Length of SampleRow Spacing* Count 1/1000th Hectare

19.1 cm (7.5in Single) 4 13.12 m20.3 cm (8in Single) 4 12.30 m24.1 cm (9.5in Single) 4 10.36 m25.4 cm (10in Single) 2 19.69 m35 cm Single 2 14.29 m38.1 cm (15in Single) 2 13.12 m50.8 cm (20in Single) 1 19.69 m55.9 cm (22in Single) 1 17.90 m70 cm Single 1 14.29 m75 cm Single 1 13.33 m76.2 cm (30in Single) 1 13.12 m91.4 cm (36in Single) 1 10.94 m96.5 cm (38in Single) 1 10.36 m101.6 cm (40in Single) 1 9.84 m70 cm Twin 1 pair 7.14 m75 cm Twin 1 pair 6.67 m76.2 cm (30in Twin) 1 pair 6.56 m91.4 cm (36in Twin) 1 pair 5.47 m96.5 cm (38in Twin) 1 pair 5.18 m101.6 cm (40in Twin) 1 pair 4.92 m* Not all spacings may be offered on implements 31982 covered by this manual.


Table of Contents

Table of Contents

Table of Contents

Great Plains, Mfg.1525 E. North St.P.O. Box 5060Salina, KS 67402