section 01 general fixings

FISCHER HOLLOW CEILING ANCHORS, FISCHER M ANCHORS, NAIL IN ANCHORS, INSULATION FIXINGS

RAWL BOLTS

RAWLSHIELDS, HOOK & EYE RAWLBOLTS

RAWL THROUGHBOLTS

SLEEVE ANCHORS

CHEMICAL ANCHORS

CAVITY FIXINGS - SPRING TOGGLES, SNAP TOGGLES, METAL ANCHORS, RAWLNUTS

CAVITY FIXINGS - FISCHER UX-R, POLYTOGGLE, FISCHER TYPE PD, METAL DRIVA, SPIT DRIVA PLUS,QWIKMASTER FIXINGS

© MIDLAND FIXINGS 2010 GENERAL FIXINGS

1 / 1

1 / 2

1 / 3

1 / 4

1 / 5

1 / 6

1 / 7

1 / 8

1 / 9

1 / 11

1 / 12

1 / 18

1 / 19

MF PLASTIC PLUGS, THORSMAN PLUGS, NYLON PLUGS, FISCHER TWISTLOCK ANCHORS, FIXING SETS

FRAME FIXINGS, HAMMER FIXINGS, UPVC FRAME FIXINGS

FISCHER HIGH PERFORMANCE FRAME FIXINGS

NON DRILL ANCHORS, FISCHER ZYKON ANCHORS

General Fixings

RAWL SAFETY PLUS ANCHORS

1

THROUGHBOLTS CONTINUED, WIREHANGERS1 / 10

CARTRIDGE RESIN SYSTEMS1 / 14

NON-EXPANDING ANCHORS - QWIK ANKERS, FRAME SCREWS, TAPCON ANCHORS, ROD HANGERS1 / 15-17

TEL: (0115) 922 1585

FISCHER HOLLOW CEILING ANCHORS, FISCHER M ANCHORS, NAIL IN ANCHORS, INSULATION FIXINGS

RAWL BOLTS

RAWLSHIELDS, HOOK & EYE RAWLBOLTS

RAWL THROUGHBOLTS

SLEEVE ANCHORS

CHEMICAL ANCHORS

CAVITY FIXINGS - SPRING TOGGLES, SNAP TOGGLES, METAL ANCHORS, RAWLNUTS

CAVITY FIXINGS - FISCHER UX-R, POLYTOGGLE, FISCHER TYPE PD, METAL DRIVA, SPIT DRIVA PLUS,QWIKMASTER FIXINGS

© MIDLAND FIXINGS 2010 GENERAL FIXINGSGENERAL FIXINGS

1 / 1

1 / 2

1 / 3

1 / 4

1 / 5

1 / 6

1 / 7

1 / 8

1 / 9

1 / 11

1 / 12

1 / 18

1 / 19

MF PLASTIC PLUGS, THORSMAN PLUGS, NYLON PLUGS, FISCHER TWISTLOCK ANCHORS, FIXING SETS

FRAME FIXINGS, HAMMER FIXINGS, UPVC FRAME FIXINGS

FISCHER HIGH PERFORMANCE FRAME FIXINGS

NON DRILL ANCHORS, FISCHER ZYKON ANCHORS

General Fixings

RAWL SAFETY PLUS ANCHORS

1

THROUGHBOLTS CONTINUED, WIREHANGERS1 / 10

CARTRIDGE RESIN SYSTEMS1 / 14

NON-EXPANDING ANCHORS - QWIK ANKERS, FRAME SCREWS, TAPCON ANCHORS, ROD HANGERS1 / 15-17

TEL: (0115) 922 1585

© MIDLAND FIXINGS 2010 1 / 1

GENERAL FIXINGS

Plastic & Nylon Wallplugs OCTOBER 2010

• Economy two way expansion plugs suitable for brick, masonry and concrete• Screws should protrude out of the end of the plug by 3-10mm

MF 1 0101150 YELLOW 22mm 5.0mm 6 - 10g 100/1000 11.20

MF 2 0101255 RED 34 5.5 6 - 10 100/1000 11.20

MF 3 0101370 BROWN 40 7.0 10 - 14 100/1000 15.00

PRODUCT MF COLOUR PLUG DRILL TO SUIT BOX/CTN PRICE CODE CODE LENGTH SIZE GAUGE QTY PER 1000


PRODUCT MF DESCRIPTION BOX PRICE CODE CODE QTY PER 100

MF PLASTIC PLUGS

• For use in very soft blocks for a secure fixing using woodscrews

GB 8 0113208 - 50mm 8.0mm 10g 25 91.73

GB 10 0113210 - 55 10.0 14 20 107.54

GB 14 0113214 - 75 14.0 10mm 10 176.72

FISCHER TWISTLOCK ANCHORS

• High quality double expansion plug - suitable for most solid substrates• Screws should be long enough to protrude 3-10mm out of the end of the plug

TP 0 0105055 WHITE 20mm 5.5mm 6-10g 100/1000 37.65

TP 1 0105155 YELLOW 25 5.5 6-10 100/1000 40.05

TP 2 0105255 RED 35 5.5 6-10 100/1000 44.55

TP 2B 0105280 BROWN 40 8.0 10-14 100/1000 71.06

TP 3 0105305 BLUE 50 10.0 10-18 100/1000 145.21

TP 4 0105206 GREEN 60 12.0 6-10mm 100/500 276.64

THORSMAN PLASTIC PLUGS

• Top quality plug suitable for all sorts of substrate, especially soft materials• Screws should protrude 3-10mm out of the end of the plug for the best result

N 5 0109005 - 25mm 5.0mm 4-8 100/10000 2.80

N 6 0109006 - 30 6.0 6-10 100/10000 4.50

N 7 0109007 - 30 7.0 8-12 100/10000 4.75

N 8 0109008 - 40 8.0 10-14 100/10000 6.30

N 10 0109010 - 50 10.0 14-18 50/1000 12.65

N 12 0109012 - 60 12.0 8-10mm 25/500 18.95

N 14 0109014 - 75 14.0 10-12 20/500 36.65

NYLON PLUGS

• For heavier fixing requirements• Product is sold complete with washers

FS 8 x 70 0117435 M8 x 70 Coachscrew/ N10 Plug 25 50.25


FIXING SETS

TEL: (0115) 922 1585© MIDLAND FIXINGS 2010 1 / 11 / 1

GENERAL FIXINGS

Plastic & Nylon Wallplugs OCTOBER 2010

• Economy two way expansion plugs suitable for brick, masonry and concrete• Screws should protrude out of the end of the plug by 3-10mm

MF 1 0101150 YELLOW 22mm 5.0mm 6 - 10g 100/1000

MF 2 0101255 RED 34 5.5 6 - 10 100/1000

MF 3 0101370 BROWN 40 7.0 10 - 14 100/1000



PRODUCT MF DESCRIPTION BOX PRICE CODE CODE QTY PER 100

MF PLASTIC PLUGS

• For use in very soft blocks for a secure fixing using woodscrews

GB 8 0113208 - 50mm 8.0mm 10g 25

GB 10 0113210 - 55 10.0 14 20

GB 14 0113214 - 75 14.0 10mm 10

FISCHER TWISTLOCK ANCHORS

• High quality double expansion plug - suitable for most solid substrates• Screws should be long enough to protrude 3-10mm out of the end of the plug

TP 0 0105055 WHITE 20mm 5.5mm 6-10g 100/1000

TP 1 0105155 YELLOW 25 5.5 6-10 100/1000 40.05

TP 2 0105255 RED 35 5.5 6-10 100/1000

TP 2B 0105280 BROWN 40 8.0 10-14 100/1000

TP 3 0105305 BLUE 50 10.0 10-18 100/1000 145.21

TP 4 0105206 GREEN 60 12.0 6-10mm 100/500 276.64

THORSMAN PLASTIC PLUGS

• Top quality plug suitable for all sorts of substrate, especially soft materials• Screws should protrude 3-10mm out of the end of the plug for the best result

N 5 0109005 - 25mm 5.0mm 4-8 100/10000

N 6 0109006 - 30 6.0 6-10 100/10000

N 7 0109007 - 30 7.0 8-12 100/10000

N 8 0109008 - 40 8.0 10-14 100/10000

N 10 0109010 - 50 10.0 14-18 50/1000

N 12 0109012 - 60 12.0 8-10mm 25/500

N 14 0109014 - 75 14.0 10-12 20/500

NYLON PLUGS

• For heavier fixing requirements• Product is sold complete with washers


FS 10 x 70 0117535 M10 x 70 Coachscrew/ N12 Plug 25

FIXING SETS

TEL: (0115) 922 1585

UF8/100 0131450 8mm 115mm 50mm 50 24.25

UF8/120 0131454 8mm 135mm 70mm 50 31.15

UF8/140 0131458 8mm 155mm 90mm 50 32.25

UF10/100 0131550 10mm 115mm 40mm 50 29.90

UF10/120 0131554 10mm 135mm 60mm 50 33.45

HF 5 x 30Z 0125215 5mm 45mm 5mm 100 5.85

HF 5 x 40Z 0125220 5mm 55mm 15mm 100 6.25

HF 5 x 50Z 0125225 5mm 65mm 25mm 100 7.25

HF 6 x 40Z 0125320 6mm 55mm 10mm 100 6.25

HF 6 x 60Z 0125330 6mm 75mm 30mm 100 9.75

HF 6 x 80Z 0125340 6mm 95mm 50mm 100 12.85

HF 8 x 60Z 0125430 8mm 75mm 20mm 100 13.75

HF 8 x 80Z 0125440 8mm 95mm 40mm 50 16.00

HF 8 x 100Z 0125450 8mm 115mm 60mm 50 19.45

HF 8 x 120Z 0125454 8mm 135mm 80mm 50 24.80

HF 10 x 100Z 0125550 10mm 115mm 50mm 50 41.15

HF 10 x 135Z 0125557 10mm 150mm 85mm 50 50.85

HF 10 x 160Z 0125562 10mm 175mm 110mm 50 61.50

LFHF 6 x 40 0126320 6mm 55mm 10mm 50 12.35

LFHF 6 x 40SS* 0127320 6mm 55mm 10mm 50 27.05

LFHF 8 x 40SS* 0127420 8mm 55mm 10mm 100 42.25


GENERAL FIXINGS

Nylon Frame Fixings OCTOBER 2010

FRAME FIXINGS

HAMMERFIX

UPVC FRAME FIXINGS For direct mounting of PVCu window frames to brickwork and masonry. Fixing clips into frame section to prevent distortion of frame when tightening.

LFHF - Large flanged hammerfix ideal for fixing builders metalwork to masonry.

*Stainless Steel nail version

For fast through fixing of battens, skirtings, wall plate straps etc. The drive screw is simply hammered in. Can be removed with screwdriver but frame fixings are recommended where adjustment is needed after installation

FF 8/60Z 0121430 8mm 70mm 10mm 100 18.75

FF 8/80Z 0121440 8mm 90mm 30mm 50 20.80

FF 8/100Z 0121450 8mm 110mm 60mm 50 25.95

FF 8/120Z 0121454 8mm 130mm 80mm 50 30.75

FF 8/135Z 0121457 8mm 145mm 95mm 50 37.80

FF 8/160Z 0121462 8mm 170mm 120mm 50 69.35

FF 10/80Z 0121540 10mm 90mm 30mm 50 32.60

FF 10/100Z 0121550 10mm 110mm 50mm 25 37.00

FF 10/120Z 0121554 10mm 125mm 65mm 25 40.20

FF 10/140Z 0121558 10mm 145mm 85mm 25 49.50

FF 10/160Z 0121562 10mm 170mm 110mm 25 61.80

FF 10/200Z 0121570 10mm 210mm 150mm 25 90.80

FF 10/240Z 0121574 10mm 250mm 190mm 25 129.20

PRODUCT MF DRILL MIN. HOLE MAX. BOX PRICES CODE CODE SIZE DEPTH FIXING QTY. PER 100

For through fixing of battens, window and door frames, skirting etc. to most common substrates.

Complete with white caps

TEL: (0115) 922 1585

UF8/100 0131450 8mm 115mm 50mm 50

UF8/120 0131454 8mm 135mm 70mm 50 31.15

UF8/140 0131458 8mm 155mm 90mm 50

UF10/100 0131550 10mm 115mm 40mm 50

UF10/120 0131554 10mm 135mm 60mm 50

HF 5 x 30Z 0125215 5mm 45mm 5mm 100

HF 5 x 40Z 0125220 5mm 55mm 15mm 100

HF 5 x 50Z 0125225 5mm 65mm 25mm 100

HF 6 x 40Z 0125320 6mm 55mm 10mm 100

HF 6 x 60Z 0125330 6mm 75mm 30mm 100

HF 6 x 80Z 0125340 6mm 95mm 50mm 100

HF 8 x 60Z 0125430 8mm 75mm 20mm 100

HF 8 x 80Z 0125440 8mm 95mm 40mm 50

HF 8 x 100Z 0125450 8mm 115mm 60mm 50

HF 8 x 120Z 0125454 8mm 135mm 80mm 50

HF 10 x 100Z 0125550 10mm 115mm 50mm 50

HF 10 x 135Z 0125557 10mm 150mm 85mm 50

HF 10 x 160Z 0125562 10mm 175mm 110mm 50

LFHF 6 x 40 0126320 6mm 55mm 10mm 50

LFHF 6 x 40SS* 0127320 6mm 55mm 10mm 50

LFHF 8 x 40SS* 0127420 8mm 55mm 10mm 100

© MIDLAND FIXINGS 2010 1 / 21 / 2

GENERAL FIXINGS

Nylon Frame Fixings OCTOBER 2010

FRAME FIXINGS

HAMMERFIX

UPVC FRAME FIXINGS For direct mounting of PVCu window frames to brickwork and masonry. Fixing clips into frame section to prevent distortion of frame when tightening.

LFHF - Large flanged hammerfix ideal for fixing builders metalwork to masonry.

*Stainless Steel nail version

For fast through fixing of battens, skirtings, wall plate straps etc. The drive screw is simply hammered in. Can be removed with screwdriver but frame fixings are recommended where adjustment is needed after installation

FF 8/60Z 0121430 8mm 70mm 10mm 100

FF 8/80Z 0121440 8mm 90mm 30mm 50

FF 8/100Z 0121450 8mm 110mm 60mm 50

FF 8/120Z 0121454 8mm 130mm 80mm 50

FF 8/135Z 0121457 8mm 145mm 95mm 50

FF 8/160Z 0121462 8mm 170mm 120mm 50

FF 10/80Z 0121540 10mm 90mm 30mm 50

FF 10/100Z 0121550 10mm 110mm 50mm 25

FF 10/120Z 0121554 10mm 125mm 65mm 25

FF 10/140Z 0121558 10mm 145mm 85mm 25

FF 10/160Z 0121562 10mm 170mm 110mm 25

FF 10/200Z 0121570 10mm 210mm 150mm 25

FF 10/240Z 0121574 10mm 250mm 190mm 25


For through fixing of battens, window and door frames, skirting etc. to most common substrates.

Complete with white caps

TEL: (0115) 922 1585

© MIDLAND FIXINGS 2010

High Performance Frame Fixings APRIL 2010

• Revolutionary design for high performance in all substrates• Especially ideal for soft blocks, perforated materials, no-fines concrete, etc. • Torx drive for positive driving

FISCHER TYPE FUR-T

FUR 8x80T 0139440 8mm 90mm 10mm 50 83.97

FUR 8x100T 0139450 8mm 110mm 30mm 50 96.32

FUR 8x120T 0139454 8mm 130mm 50mm 50 108.66

FUR 10x100T 0139550 10mm 110mm 30mm 50 113.60

FUR 10x115T 0139553 10mm 125mm 45mm 50 129.65

FUR 10x135T 0139557 10mm 145mm 65mm 50 156.82

FUR 10x160T 0139562 10mm 170mm 90mm 50 200.04

FUR 10x185T 0139567 10mm 195mm 115mm 50 277.83

FUR 10x200T 0139570 10mm 210mm 130mm 50 364.27

FUR 10x230T 0139573 10mm 240mm 160mm 50 456.88


FUR 8x80SS 0140440 8mm 90mm 10mm 50 86.44

FUR 8x100SS 0140450 8mm 110mm 30mm 50 99.40

FUR 10x80SS 0140540 10mm 90mm 10mm 50 103.11

FUR 10x100SS 0140550 10mm 110mm 30mm 50 117.31Other sizes available to order

Same as above fixing but with hexagon head screw. FISCHER TYPE FUR-SS

SXR 8x80Z 0141440 8mm 90mm 30mm 50 42.38

SXR 8x100Z 0141450 8mm 110mm 50mm 50 54.29

SXR 8x120Z 0141454 8mm 130mm 70mm 50 63.29

SXR 10x100Z 0141550 10mm 110mm 50mm 50 90.38

SXR 10x120Z 0141554 10mm 130mm 70mm 50 103.11

SXR 10x140Z 0141558 10mm 150mm 90mm 50 115.95

SXR 10x160Z 0141562 10mm 170mm 110mm 50 156.33

SXR 10x180Z 0141566 10mm 190mm 130mm 50 220.91

SXR 10x200T 0141570 10mm 210mm 150mm 50 289.68

SXR 10x230T 0141573 10mm 240mm 180mm 50 363.41

SXR 10x260T 0141576 10mm 270mm 210mm 50 459.98

• High performance, high load, genuine all-round fixing• European Technical Approval covering 41 different building materials• Performs in solid, perforated and soft materials

FISCHER TYPE SXR-T

1 / 3GENERAL FIXINGS

SXR 10x60FUS 0142530 10mm 70mm 10mm 50 79.02

SXR 10x80FUS 0142540 10mm 90mm 30mm 50 87.06

SXR 10x100FUS 0142550 10mm 110mm 50mm 50 99.28

SXR 10x120FUS 0142554 10mm 130mm 70mm 50 116.56

SXR 10x140FUS 0142558 10mm 150mm 90mm 50 137.12

SXR 10x160FUS 0142562 10mm 170mm 110mm 50 172.26

Same as above fixing but with hexagon head screw. FISCHER TYPE SXR-FUS

TEL: (0115) 922 1585© MIDLAND FIXINGS 2010

High Performance Frame Fixings APRIL 2010

• Revolutionary design for high performance in all substrates• Especially ideal for soft blocks, perforated materials, no-fines concrete, etc. • Torx drive for positive driving

FISCHER TYPE FUR-T

FUR 8x80T 0139440 8mm 90mm 10mm 50

FUR 8x100T 0139450 8mm 110mm 30mm 50

FUR 8x120T 0139454 8mm 130mm 50mm 50

FUR 10x100T 0139550 10mm 110mm 30mm 50

FUR 10x115T 0139553 10mm 125mm 45mm 50

FUR 10x135T 0139557 10mm 145mm 65mm 50

FUR 10x160T 0139562 10mm 170mm 90mm 50

FUR 10x185T 0139567 10mm 195mm 115mm 50 277.83

FUR 10x200T 0139570 10mm 210mm 130mm 50 364.27

FUR 10x230T 0139573 10mm 240mm 160mm 50


FUR 8x80SS 0140440 8mm 90mm 10mm 50

FUR 8x100SS 0140450 8mm 110mm 30mm 50

FUR 10x80SS 0140540 10mm 90mm 10mm 50

FUR 10x100SS 0140550 10mm 110mm 30mm 50 Other sizes available to order

Same as above fixing but with hexagon head screw. FISCHER TYPE FUR-SS

SXR 8x80Z 0141440 8mm 90mm 30mm 50

SXR 8x100Z 0141450 8mm 110mm 50mm 50

SXR 8x120Z 0141454 8mm 130mm 70mm 50

SXR 10x100Z 0141550 10mm 110mm 50mm 50

SXR 10x120Z 0141554 10mm 130mm 70mm 50

SXR 10x140Z 0141558 10mm 150mm 90mm 50

SXR 10x160Z 0141562 10mm 170mm 110mm 50

SXR 10x180Z 0141566 10mm 190mm 130mm 50 220.91

SXR 10x200T 0141570 10mm 210mm 150mm 50 289.68

SXR 10x230T 0141573 10mm 240mm 180mm 50 363.41

SXR 10x260T 0141576 10mm 270mm 210mm 50 459.98

• High performance, high load, genuine all-round fixing• European Technical Approval covering 41 different building materials• Performs in solid, perforated and soft materials

FISCHER TYPE SXR-T

1 / 31 / 3GENERAL FIXINGS

SXR 10x60FUS 0142530 10mm 70mm 10mm 50

SXR 10x80FUS 0142540 10mm 90mm 30mm 50

SXR 10x100FUS 0142550 10mm 110mm 50mm 50

SXR 10x120FUS 0142554 10mm 130mm 70mm 50

SXR 10x140FUS 0142558 10mm 150mm 90mm 50

SXR 10x160FUS 0142562 10mm 170mm 110mm 50

Same as above fixing but with hexagon head screw. FISCHER TYPE SXR-FUS

TEL: (0115) 922 1585


GENERAL FIXINGS

Hammerset Anchors APRIL 2010

• Internally threaded anchor for use in concrete• Expanded by hammer and setting tool • Accepts bolts, threaded bar etc.

• Zykon is a high performance, stress free, internally threaded anchor for concrete• An undercut hole is drilled using the Zykon drill and the anchor is set into the undercut• Gives very high permissible loads in all areas of the concrete

• For drilling undercut hole

FISCHER ZYKON HAMMERSET

FZEA10 0205010 M 8 40mm N/A FZUB 10 x 40 100 69.82

FZEA12 0205012 M 10 40mm N/A FZUB 12 x 40 100 88.38

FZEA14 0205014 M 12 40mm N/A FZUB 14 x 40 50 135.96

PRODUCT MF THREAD ANCHOR MAX.FIX DRILL BOX PRICE CODE CODE DIA. LENGTH THICKNESS SIZE QTY PER 100

PRODUCT MF PRICE CODE CODE EACH

Undercut non-drill anchor for stress free loads. Internal thread ideal for threaded bar.

FZUB10 x 40 0206520 58.34

FZUB12 x 40 0206620 60.41

FZUB14 x 40 0206720 69.84

FISCHER ZYKON UNIVERSAL DRILL

FISCHER ZYKON HAMMERSET TOOL

FZED10 x 40 0207520 17.96 each

FZED12 x 40 0207620 17.96 each

FZED14 x 40 0207720 17.96 each

TEL: (0115) 922 1585

NON DRILL ANCHORS

FOR STAINLESS STEEL VERSION SEE THE MF STAINLESS CATALOGUE

RIMMED NON DRILL ANCHORS. Rim ensures anchor always remains flush with surface of substrate. Very shallow embedment depth

M 6 0215006 8mm 25mm 25mm 8mm 100 16.00

M 8 0215008 10 30 30 12 100 21.20

M 10 0215010 12 40 40 16 50 28.00

M 12 0215012 15 50 50 18 25 46.20

M 16 0215016 20 60 60 25 20 85.00

M 20 0215020 25 80 80 35 10 161.00

SIZE MF DRILL ANCHOR HOLE THREAD BOX PRICE CODE SIZE LENGTH DEPTH LENGTH QUANTITY PER 100

SETTING TOOLS Essential for accurate setting of Non Drill Anchors.

RND 8 0217008 10 30 32 15 100 30.85

RND 10 0217010 12 30 33 15 100 39.30

M 6 0220006 1 5.30

M 8 0220008 1 6.45

M 10 0220010 1 7.30

M 12 0220012 1 7.50

M 16 0220016 1 8.70

M 20 0220020 1 10.20


GENERAL FIXINGS

Hammerset Anchors APRIL 2010

• Internally threaded anchor for use in concrete• Expanded by hammer and setting tool • Accepts bolts, threaded bar etc.

• Zykon is a high performance, stress free, internally threaded anchor for concrete• An undercut hole is drilled using the Zykon drill and the anchor is set into the undercut• Gives very high permissible loads in all areas of the concrete

• For drilling undercut hole

FISCHER ZYKON HAMMERSET

FZEA10 0205010 M 8 40mm N/A FZUB 10 x 40 100

FZEA12 0205012 M 10 40mm N/A FZUB 12 x 40 100

FZEA14 0205014 M 12 40mm N/A FZUB 14 x 40 50 135.96

PRODUCT MF THREAD ANCHOR MAX.FIX DRILL BOX PRICE CODE CODE DIA. LENGTH THICKNESS SIZE QTY PER 100

PRODUCT MF PRICE CODE CODE EACH

Undercut non-drill anchor for stress free loads. Internal thread ideal for threaded bar.

FZUB10 x 40 0206520

FZUB12 x 40 0206620 60.41

FZUB14 x 40 0206720 69.84

FISCHER ZYKON UNIVERSAL DRILL

FISCHER ZYKON HAMMERSET TOOL

FZED10 x 40 0207520

FZED12 x 40 0207620

FZED14 x 40 0207720 17.96 each

TEL: (0115) 922 1585

NON DRILL ANCHORS

FOR STAINLESS STEEL VERSION SEE THE MF STAINLESS CATALOGUE

RIMMED NON DRILL ANCHORS. Rim ensures anchor always remains flush with surface of substrate. Very shallow embedment depth

M 6 0215006 8mm 25mm 25mm 8mm 100

M 8 0215008 10 30 30 12 100

M 10 0215010 12 40 40 16 50

M 12 0215012 15 50 50 18 25

M 16 0215016 20 60 60 25 20

M 20 0215020 25 80 80 35 10

SIZE MF DRILL ANCHOR HOLE THREAD BOX PRICE CODE SIZE LENGTH DEPTH LENGTH QUANTITY PER 100

SETTING TOOLS Essential for accurate setting of Non Drill Anchors.

RND 8 0217008 10 30 32 15 100 0217008 10 30 32 15 100 0217008 10 30 32 15 100 0217008 10 30 32 15 100 0217008 10 30 32 15 100 0217008 10 30 32 15 100 0217008 10 30 32 15 100

RND 10 0217010 12 30 33 15 100 0217010 12 30 33 15 100 0217010 12 30 33 15 100 0217010 12 30 33 15 100 0217010 12 30 33 15 100 0217010 12 30 33 15 100 0217010 12 30 33 15 100

M 6 0220006 1

M 8 0220008 1

M 10 0220010 1 7.30

M 12 0220012 1

M 16 0220016 1

M 20 0220020 1 10.20


GENERAL FIXINGS

Other Fixing Anchors APRIL 2010

TEL: (0115) 922 1585

FHY M6 0211006 M 6 37 10 116.50

FHY M8 0211008 M 8 43 12 170.33

FHY M10 0211010 M 10 52 16 233.02

PRODUCT MF THREAD FIXING DRILL PRICE CODE CODE DIA. LENGTH DIAMETER PER 100

PRODUCT MF DRILL MAX. BOX PRICE CODE CODE SIZE LENGTH FIXING QTY. PER 100

HOLLOW CEILING ANCHORS – FHY • Specially developed for fixing to concrete hollow ceiling slabs• High expansion capacity- performs in solid and hollow materials• Female thread for accepting bolts, threaded bar etc.

• High performance nylon anchor with female thread• Performs well in poor masonry, hollow pots, lightweight blocks etc.• Corrosion proof anchor

• Zinc alloy fixing for quick installation by hammering• Ideal for installing drywall systems, suspended ceilings etc.

• One piece nylon fixing for fastening rigid insulation to masonry• Hole is drilled straight through the insulation and fixing is hammered in

HEAVY DUTY NYLON ANCHORS TYPE ‘M’

NAIL IN ANCHORS

NA 6x 40 0144320 6mm 40mm 15mm 100 19.60

NYLON INSULATION FIXINGS

NIN 70 0148070 8mm 70mm 30-40mm 32mm 500 11.35

NIN 90 0148090 8mm 90mm 50-60mm 32mm 500 12.40

NIN 110 0148110 8mm 110mm 70-80mm 32mm 500 14.70

PRODUCT MF DRILL LENGTH INSULATION HEAD BOX PRICES CODE CODE SIZE THICKNESS DIA. QTY. PER 100

M6 0201006 12mm 50mm 40mm 50 103.32

M8 0201008 16mm 65mm 50mm 20 188.94

M10 0201010 20mm 80mm 60mm 10 327.74

M12 0201012 24mm 90mm 70mm 5 509.86

PRODUCT MF DRILL MIN. HOLE MAX. BOLT BOX PRICE CODE CODE SIZE DEPTH LENGTH QTY. PER 100


GENERAL FIXINGS

Other Fixing Anchors APRIL 2010

TEL: (0115) 922 1585

FHY M6 0211006 M 6 37 10 116.50

FHY M8 0211008 M 8 43 12

FHY M10 0211010 M 10 52 16

PRODUCT MF THREAD FIXING DRILL PRICE CODE CODE DIA. LENGTH DIAMETER PER 100

PRODUCT MF DRILL MAX. BOX PRICE CODE CODE SIZE LENGTH FIXING QTY. PER 100

HOLLOW CEILING ANCHORS – FHY • Specially developed for fixing to concrete hollow ceiling slabs• High expansion capacity- performs in solid and hollow materials• Female thread for accepting bolts, threaded bar etc.

• High performance nylon anchor with female thread• Performs well in poor masonry, hollow pots, lightweight blocks etc.• Corrosion proof anchor

• Zinc alloy fixing for quick installation by hammering• Ideal for installing drywall systems, suspended ceilings etc.

• One piece nylon fixing for fastening rigid insulation to masonry• Hole is drilled straight through the insulation and fixing is hammered in

HEAVY DUTY NYLON ANCHORS TYPE ‘M’

NAIL IN ANCHORS

NA 6x 40 0144320 6mm 40mm 15mm 100

NYLON INSULATION FIXINGS

NIN 70 0148070 8mm 70mm 30-40mm 32mm 500 11.35

NIN 90 0148090 8mm 90mm 50-60mm 32mm 500 12.40

NIN 110 0148110 8mm 110mm 70-80mm 32mm 500 14.70

PRODUCT MF DRILL LENGTH INSULATION HEAD BOX PRICES CODE CODE SIZE THICKNESS DIA. QTY. PER 100

M6 0201006 12mm 50mm 40mm 50 103.32

M8 0201008 16mm 65mm 50mm 20

M10 0201010 20mm 80mm 60mm 10

M12 0201012 24mm 90mm 70mm 5

PRODUCT MF DRILL MIN. HOLE MAX. BOLT BOX PRICE CODE CODE SIZE DEPTH LENGTH QTY. PER 100


GENERAL FIXINGS

Rawl Safety Plus Anchors OCTOBER 2010

SPM 815 L 0225315 12mm 90mm 80mm 15mm 50 212.50 SPM 825 LL 0225325 80mm * 25mm 50 218.75 SPM 840 L 0225340 110mm 40mm 50 262.50 SPM 1020 L 0225420 15mm 105mm 90mm 20mm 50 262.50 SPM 1025 LL 0225425 90mm * 25mm 50 300.00 SPM 1040 L 0225440 120mm 40mm 50 281.25 SPM 1060 L 0225460 145mm 90mm 60mm 50 293.75 SPM 1225 LL 0225520 18mm 100mm 85mm* 25mm 25 337.50 SPM 1225 L 0225525 125mm 105mm 25mm 25 381.25 SPM 1250 L 0225550 150mm 105mm 50mm 25 443.75 SPM 1625 L 0225625 24mm 145mm 125mm 25mm 10 1000.00 SPM 1630 LL 0225630 130mm 100mm* 30mm 10 1318.75 SPM 1650 L 0225650 170mm 125mm 50mm 10 1068.75 SPM 2030 L 0225730 28mm 175mm 155mm 30mm 10 1900.00

LOOSE BOLT – HEX HEAD

BOLT PROJECTING

COUNTERSUNK LOOSE BOLT

* Limited Embedment These have lower working loads.Technical details available on request.

Rawl Safety Plus are high performance through fixings for concrete, providing maximum reliability in safety critical applications, even when concrete is cracked.

PRODUCTCODE

MFCODE

DRILLDIA.

TOTALLENGTH

MIN. HOLEDEPTH

MAX. FIX.THICKNESS

BOXQTY

PRICEPER 100

SPM 815 P 0226315 12mm 95mm 80mm 15mm 50 387.50 SPM 1020 P 0226420 15mm 110mm 90mm 20mm 50 393.75 SPM 1225 P 0226525 18mm 135mm 105mm 25mm 25 575.80 SPM 1250 P 0226550 160mm 50mm 25 812.50 SPM 1625 P 0226625 24mm 160mm 125mm 25mm 10 1293.75 SPM 2030 P 0226730 28mm 190mm 155mm 30mm 10 2106.25

PRODUCTCODE

MFCODE

DRILLDIA.

TOTALLENGTH

MIN. HOLEDEPTH

MAX. FIX.THICKNESS

BOXQTY

PRICEPER 100

SPM 820 CSK 0227320 12mm 90mm 80mm 20mm 50 256.25 SPM 1025 CSK 0227425 15mm 105mm 90mm 25mm 50 352.90 SPM 1230 CSK 0227530 18mm 125mm 105mm 30mm 25 481.25 SPM 1630 CSK 0227630 24mm 145mm 125mm 30mm 10 1018.75

PRODUCTCODE

MFCODE

DRILLDIA.

TOTALLENGTH

MIN. HOLEDEPTH

MAX. FIX.THICKNESS

BOXQTY

PRICEPER 100


GENERAL FIXINGS

Rawl Safety Plus Anchors OCTOBER 2010

SPM 815 L 0225315 12mm 90mm 80mm 15mm 50 SPM 825 LL 0225325 80mm * 25mm 50 218.75

SPM 840 L 0225340 110mm 40mm 50 SPM 1020 L 0225420 15mm 105mm 90mm 20mm 50

SPM 1025 LL 0225425 90mm * 25mm 50 300.00 SPM 1040 L 0225440 120mm 40mm 50 SPM 1060 L 0225460 145mm 90mm 60mm 50 293.75 SPM 1225 LL 0225520 18mm 100mm 85mm* 25mm 25 337.50 SPM 1225 L 0225525 125mm 105mm 25mm 25 SPM 1250 L 0225550 150mm 105mm 50mm 25

SPM 1625 L 0225625 24mm 145mm 125mm 25mm 10 SPM 1630 LL 0225630 130mm 100mm* 30mm 10 1318.75 SPM 1650 L 0225650 170mm 125mm 50mm 10 1068.75 SPM 2030 L 0225730 28mm 175mm 155mm 30mm 10 1900.00

LOOSE BOLT – HEX HEAD

BOLT PROJECTING

COUNTERSUNK LOOSE BOLT

* Limited Embedment These have lower working loads.Technical details available on request.

Rawl Safety Plus are high performance through fixings for concrete, providing maximum reliability in safety critical applications, even when concrete is cracked.

PRODUCTCODE

MFCODE

DRILLDIA.

TOTALLENGTH

MIN. HOLEDEPTH

MAX. FIX.THICKNESS

BOXQTY

SPM 815 P 0226315 12mm 95mm 80mm 15mm 50 387.50 SPM 1020 P 0226420 15mm 110mm 90mm 20mm 50 393.75 SPM 1225 P 0226525 18mm 135mm 105mm 25mm 25 575.80 SPM 1250 P 0226550 160mm 50mm 25 812.50 SPM 1625 P 0226625 24mm 160mm 125mm 25mm 10 1293.75 SPM 2030 P 0226730 28mm 190mm 155mm 30mm 10 2106.25

PRODUCTCODE

MFCODE

DRILLDIA.

TOTALLENGTH

MIN. HOLEDEPTH

MAX. FIX.THICKNESS

BOXQTY

SPM 820 CSK 0227320 12mm 90mm 80mm 20mm 50 SPM 1025 CSK 0227425 15mm 105mm 90mm 25mm 50 SPM 1230 CSK 0227530 18mm 125mm 105mm 30mm 25 481.25 SPM 1630 CSK 0227630 24mm 145mm 125mm 30mm 10 1018.75

PRODUCTCODE

MFCODE

DRILLDIA.

TOTALLENGTH

MIN. HOLEDEPTH

MAX. FIX.THICKNESS

BOXQTY

TEL: (0115) 922 1585


GENERAL FIXINGS

Rawlbolts OCTOBER 2010

Bolt can be removed from shield

M6 10L 0239310 55mm 40mm 10mm 50mm 12mm 50 125.00

M6 25L 0239325 70 40 25 50 12 50 125.00

M6 40L 0239340 85 40 40 50 12 50 143.75

M8 10L 0239410 65 50 10 55 14 50 137.50

M8 25L 0239425 80 50 25 55 14 50 162.50

M8 40L 0239440 95 50 40 55 14 50 156.25

M10 10L 0239510 75 60 10 65 16 50 175.00

M10 25L 0239525 90 60 25 65 16 50 193.75

M10 50L 0239550 115 60 50 65 16 50 193.75

M10 75L 0239575 140 60 75 65 16 50 212.50

M12 10L 0239610 90 75 10 85 20 25 337.50

M12 25L 0239625 105 75 25 85 20 25 350.00

M12 40L 0239640 120 75 40 85 20 25 337.50

M12 60L 0239660 140 75 60 85 20 25 437.50

M16 15L 0239815 135 100 15 125 25 10 700.00

M16 30L 0239830 150 100 30 125 25 10 737.50

M16 60L 0239860 180 100 60 125 25 10 862.50

M20 60L 0239930 195 130 60 140 32 10 1768.75

M20 100L 0239950 235 130 100 140 32 10 1912.50

M24 100L 0239960 255 150 100 160 38 5 2551.20

M24 150L 0239975 300 150 150 160 38 5 2684.00

LOOSE BOLT TYPE

Stud cannot be removed from shield

M6 10P 0240310 65mm 40mm 10mm 50mm 12mm 50 118.75

M6 25P 0240325 80 40 25 50 12 50 137.50

M6 60P 0240360 115 40 60 50 12 50 125.00

M8 10P 0240410 75 50 10 55 14 50 125.00

M8 25P 0240425 90 50 25 55 14 50 137.50

M8 60P 0240460 125 50 60 55 14 50 175.00

M10 15P 0240515 90 60 15 65 16 50 184.70

M10 30P 0240530 105 60 30 65 16 50 192.75

M10 60P 0240560 135 60 60 65 16 50 187.50

M12 15P 0240615 110 75 15 85 20 25 300.15

M12 30P 0240630 125 75 30 85 20 25 314.55

M12 75P 0240675 170 75 75 85 20 25 389.60

M16 15P 0240815 150 100 15 125 25 10 704.20

M16 35P 0240835 170 100 35 125 25 10 721.50

M16 75P 0240875 210 100 75 125 25 10 731.25

M20 15P 0240915 170 130 15 140 32 10 1112.50

M20 30P 0240930 185 130 30 140 32 10 1162.50

M20 100P 0240950 255 130 100 140 32 10 1231.25

M24 75P 0240975 255 150 75 160 38 5 2030.40

M24 120P 0240990 300 150 120 160 38 5 2145.10

BOLT PROJECTION

* First half of code = Thread Diameter Second half = Fixing Thickness

The original heavy duty expansion fixing for brickwork, stone, masonry and concrete. Shield Anchors have a higher degree of expansion than other types of anchors offering excellent tolerance to variations in hole size. Combines ease of installation with good load carrying capacity.

PRODUCTCODE

MFCODE

TOTALLENGTH

SHELLLENGTH

MAXFIXING

DRILLDEPTH

DRILLDIA.

BOXQTY

PRICEPER 100


GENERAL FIXINGS


Bolt can be removed from shield

M6 10L 0239310 55mm 40mm 10mm 50mm 12mm 50 125.00

M6 25L 0239325 70 40 25 50 12 50 125.00

M6 40L 0239340 85 40 40 50 12 50 143.75

M8 10L 0239410 65 50 10 55 14 50 137.50

M8 25L 0239425 80 50 25 55 14 50 162.50

M8 40L 0239440 95 50 40 55 14 50 156.25

M10 10L 0239510 75 60 10 65 16 50 175.00

M10 25L 0239525 90 60 25 65 16 50 193.75

M10 50L 0239550 115 60 50 65 16 50 193.75

M10 75L 0239575 140 60 75 65 16 50 212.50

M12 10L 0239610 90 75 10 85 20 25 337.50

M12 25L 0239625 105 75 25 85 20 25 350.00

M12 40L 0239640 120 75 40 85 20 25 337.50

M12 60L 0239660 140 75 60 85 20 25 437.50

M16 15L 0239815 135 100 15 125 25 10 700.00

M16 30L 0239830 150 100 30 125 25 10 737.50

M16 60L 0239860 180 100 60 125 25 10 862.50

M20 60L 0239930 195 130 60 140 32 10 1768.75

M20 100L 0239950 235 130 100 140 32 10 1912.50

M24 100L 0239960 255 150 100 160 38 5

M24 150L 0239975 300 150 150 160 38 5 2684.00

LOOSE BOLT TYPE

Stud cannot be removed from shield

M6 10P 0240310 65mm 40mm 10mm 50mm 12mm 50 0240310 65mm 40mm 10mm 50mm 12mm 50 0240310 65mm 40mm 10mm 50mm 12mm 50 0240310 65mm 40mm 10mm 50mm 12mm 50 0240310 65mm 40mm 10mm 50mm 12mm 50 0240310 65mm 40mm 10mm 50mm 12mm 50 0240310 65mm 40mm 10mm 50mm 12mm 50 0240310 65mm 40mm 10mm 50mm 12mm 50 118.75

M6 25P 0240325 80 40 25 50 12 50 0240325 80 40 25 50 12 50 0240325 80 40 25 50 12 50 0240325 80 40 25 50 12 50 0240325 80 40 25 50 12 50 0240325 80 40 25 50 12 50 0240325 80 40 25 50 12 50 0240325 80 40 25 50 12 50 137.50

M6 60P 0240360 115 40 60 50 12 50 0240360 115 40 60 50 12 50 0240360 115 40 60 50 12 50 0240360 115 40 60 50 12 50 0240360 115 40 60 50 12 50 0240360 115 40 60 50 12 50 0240360 115 40 60 50 12 50 0240360 115 40 60 50 12 50 125.00

M8 10P 0240410 75 50 10 55 14 50 0240410 75 50 10 55 14 50 0240410 75 50 10 55 14 50 0240410 75 50 10 55 14 50 0240410 75 50 10 55 14 50 0240410 75 50 10 55 14 50 0240410 75 50 10 55 14 50 0240410 75 50 10 55 14 50 125.00

M8 25P 0240425 90 50 25 55 14 50 0240425 90 50 25 55 14 50 0240425 90 50 25 55 14 50 0240425 90 50 25 55 14 50 0240425 90 50 25 55 14 50 0240425 90 50 25 55 14 50 0240425 90 50 25 55 14 50 0240425 90 50 25 55 14 50 137.50

M8 60P 0240460 125 50 60 55 14 50 0240460 125 50 60 55 14 50 0240460 125 50 60 55 14 50 0240460 125 50 60 55 14 50 0240460 125 50 60 55 14 50 0240460 125 50 60 55 14 50 0240460 125 50 60 55 14 50 0240460 125 50 60 55 14 50 175.00

M10 15P 0240515 90 60 15 65 16 50 0240515 90 60 15 65 16 50 0240515 90 60 15 65 16 50 0240515 90 60 15 65 16 50 0240515 90 60 15 65 16 50 0240515 90 60 15 65 16 50 0240515 90 60 15 65 16 50 0240515 90 60 15 65 16 50 184.70

M10 30P 0240530 105 60 30 65 16 50 0240530 105 60 30 65 16 50 0240530 105 60 30 65 16 50 0240530 105 60 30 65 16 50 0240530 105 60 30 65 16 50 0240530 105 60 30 65 16 50 0240530 105 60 30 65 16 50 0240530 105 60 30 65 16 50 192.75

M10 60P 0240560 135 60 60 65 16 50 0240560 135 60 60 65 16 50 0240560 135 60 60 65 16 50 0240560 135 60 60 65 16 50 0240560 135 60 60 65 16 50 0240560 135 60 60 65 16 50 0240560 135 60 60 65 16 50 0240560 135 60 60 65 16 50 187.50

M12 15P 0240615 110 75 15 85 20 25 0240615 110 75 15 85 20 25 0240615 110 75 15 85 20 25 0240615 110 75 15 85 20 25 0240615 110 75 15 85 20 25 0240615 110 75 15 85 20 25 0240615 110 75 15 85 20 25 0240615 110 75 15 85 20 25 300.15

M12 30P 0240630 125 75 30 85 20 25 0240630 125 75 30 85 20 25 0240630 125 75 30 85 20 25 0240630 125 75 30 85 20 25 0240630 125 75 30 85 20 25 0240630 125 75 30 85 20 25 0240630 125 75 30 85 20 25 0240630 125 75 30 85 20 25 314.55

M12 75P 0240675 170 75 75 85 20 25 0240675 170 75 75 85 20 25 0240675 170 75 75 85 20 25 0240675 170 75 75 85 20 25 0240675 170 75 75 85 20 25 0240675 170 75 75 85 20 25 0240675 170 75 75 85 20 25 0240675 170 75 75 85 20 25 389.60

M16 15P 0240815 150 100 15 125 25 10 0240815 150 100 15 125 25 10 0240815 150 100 15 125 25 10 0240815 150 100 15 125 25 10 0240815 150 100 15 125 25 10 0240815 150 100 15 125 25 10 0240815 150 100 15 125 25 10 0240815 150 100 15 125 25 10 704.20

M16 35P 0240835 170 100 35 125 25 10 0240835 170 100 35 125 25 10 0240835 170 100 35 125 25 10 0240835 170 100 35 125 25 10 0240835 170 100 35 125 25 10 0240835 170 100 35 125 25 10 0240835 170 100 35 125 25 10 0240835 170 100 35 125 25 10 721.50

M16 75P 0240875 210 100 75 125 25 10 0240875 210 100 75 125 25 10 0240875 210 100 75 125 25 10 0240875 210 100 75 125 25 10 0240875 210 100 75 125 25 10 0240875 210 100 75 125 25 10 0240875 210 100 75 125 25 10 0240875 210 100 75 125 25 10 731.25

M20 15P 0240915 170 130 15 140 32 10 0240915 170 130 15 140 32 10 0240915 170 130 15 140 32 10 0240915 170 130 15 140 32 10 0240915 170 130 15 140 32 10 0240915 170 130 15 140 32 10 0240915 170 130 15 140 32 10 0240915 170 130 15 140 32 10 1112.50

M20 30P 0240930 185 130 30 140 32 10 0240930 185 130 30 140 32 10 0240930 185 130 30 140 32 10 0240930 185 130 30 140 32 10 0240930 185 130 30 140 32 10 0240930 185 130 30 140 32 10 0240930 185 130 30 140 32 10 0240930 185 130 30 140 32 10 1162.50

M20 100P 0240950 255 130 100 140 32 10 0240950 255 130 100 140 32 10 0240950 255 130 100 140 32 10 0240950 255 130 100 140 32 10 0240950 255 130 100 140 32 10 0240950 255 130 100 140 32 10 0240950 255 130 100 140 32 10 0240950 255 130 100 140 32 10 1231.25

M24 75P 0240975 255 150 75 160 38 5 0240975 255 150 75 160 38 5 0240975 255 150 75 160 38 5 0240975 255 150 75 160 38 5 0240975 255 150 75 160 38 5 0240975 255 150 75 160 38 5 0240975 255 150 75 160 38 5 0240975 255 150 75 160 38 5

M24 120P 0240990 300 150 120 160 38 5 0240990 300 150 120 160 38 5 0240990 300 150 120 160 38 5 0240990 300 150 120 160 38 5 0240990 300 150 120 160 38 5 0240990 300 150 120 160 38 5 0240990 300 150 120 160 38 5 0240990 300 150 120 160 38 5 2145.10

BOLT PROJECTION

* First half of code = Thread Diameter Second half = Fixing Thickness

The original heavy duty expansion fixing for brickwork, stone, masonry and concrete. Shield Anchors have a higher degree of expansion than other types of anchors offering excellent tolerance to variations in hole size. Combines ease of installation with good load carrying capacity.

PRODUCTCODE

MFCODE

TOTALLENGTH

SHELLLENGTH

MAXFIXING

DRILLDEPTH

DRILLDIA.

BOXQTY

TEL: (0115) 922 1585


GENERAL FIXINGS


RAWLSHIELDS

For a wide range of heavy duty applications

M6S 0241006 12mm 50 mm 100 112.50

M8S 0241008 14 55 100 114.30

M10S 0241010 16 65 100 135.65

M12S 0241012 20 85 50 219.35

M16S 0241016 25 125 25 519.50

M20S 0241020 32 140 15 1387.50

M24S 0241024 38 160 5 2014.45

M6H 0242006 12mm 50 mm 100 168.75

M8H 0242008 14 55 50 206.25

M10H 0242010 16 65 50 294.35

M12H 0242012 20 85 25 500.00

M6E 0243006 12mm 50 mm 100 168.75

M8E 0243008 14 55 50 200.00

M10E 0243010 16 65 50 294.35

M12E 0243012 20 85 25 475.00

Forged eye

HOOK RAWLBOLTS

EYE RAWLBOLTS

PRODUCTCODE

MFCODE

HOLEDIAMETER

HOLEDEPTH

BOXQUANTITY

PRICEPER 100


GENERAL FIXINGS


RAWLSHIELDS

For a wide range of heavy duty applications

M6S 0241006 12mm 50 mm 100

M8S 0241008 14 55 100

M10S 0241010 16 65 100

M12S 0241012 20 85 50

M16S 0241016 25 125 25

M20S 0241020 32 140 15

M24S 0241024 38 160 5

M6H 0242006 12mm 50 mm 100

M8H 0242008 14 55 50

M10H 0242010 16 65 50

M12H 0242012 20 85 25

M6E 0243006 12mm 50 mm 100

M8E 0243008 14 55 50

M10E 0243010 16 65 50

M12E 0243012 20 85 25

Forged eye

HOOK RAWLBOLTS

EYE RAWLBOLTS

PRODUCTCODE

MFCODE

HOLEDIAMETER

HOLEDEPTH

BOXQUANTITY

TEL: (0115) 922 1585


GENERAL FIXINGS

Throughbolts - RAWLPLUG APRIL 2009

THROUGHBOLTS – ZINC PLATED

M6 x 40 0246220 30mm 3mm 100 39.00

M6 x 55 0246227 30 16 100 46.30

M6 x 70 0246235 30 32 100 46.80

M6 x 85 0246242 30 46 100 49.40

M6 x 95 0246247 30 56 100 50.95

M8 x 65 0246332 40 15 100 50.95

M8 x 80 0246340 40 30 100 53.60

M8 x 95 0246347 40 45 100 56.70

M8 x 115 0246353 40 65 100 61.35

M10 x 65 0246432 50 5 50 65.50

M10 x 80 0246440 50 16 50 70.20

M10 x 95 0246447 50 32 50 77.75

M10 x 115 0246453 50 52 50 89.70

M10 x 130 0246456 50 67 50 106.60

M12 x 80 0246540 60 5 50 93.60

M12 x 100 0246550 60 24 50 96.45

M12 x 120 0246554 60 44 50 106.60

M12 x 135 0246557 60 58 50 122.20

M12 x 150 0246560 60 73 50 127.40

M12 x 180 0246566 60 105 50 192.40

M12 x 235 0246573 60 160 50 259.00

M16 x 105 0246651 80 5 25 192.05

M16 x 140 0246658 80 40 25 215.10

M16 x 180 0246666 80 80 25 251.70

M16 x 220 0246672 80 120 25 421.85

M16 x 280 0246678 80 180 15 654.20

M20 x 125 0246755 100 5 25 427.25

M20 x 160 0246762 100 40 25 494.50

M20 x 200 0246770 100 80 10 715.00

M20 x 300 0246780 100 180 10 800.80

M24 x 180 0246866 120 35 10 946.40

M24 x 260 0246876 120 115 10 1144.00

SIZE MF HOLE MAX.FIX. BOX PRICE CODE DEPTH* THICKNESS QTY. PER 100

* Minimum recommended hole depth in concrete of 25N/mm2 strength.

In weaker concrete embedment should be deeper.

Throughbolts should not be used in brickwork or aggregate blocks.

These short Throughbolts have reduced embedment depths. Load and torque figures should be reduced accordingly; tighten to 5 full turns from finger tight.

We do not recommend short Throughbolts to be used as structural load fixings.

Throughbolt is a versatile, cost effective anchor, combining ease of installation with good load carrying characteristics. It requires a hole the same diameter as the bolt and so is ideal for through fixing. For use in concrete with minimum strength of 20N/mm2 .


GENERAL FIXINGS

Throughbolts - RAWLPLUG APRIL 2009

THROUGHBOLTS – ZINC PLATED

M6 x 40 0246220 30mm 3mm 100

M6 x 55 0246227 30 16 100

M6 x 70 0246235 30 32 100

M6 x 85 0246242 30 46 100

M6 x 95 0246247 30 56 100

M8 x 65 0246332 40 15 100

M8 x 80 0246340 40 30 100

M8 x 95 0246347 40 45 100

M8 x 115 0246353 40 65 100

M10 x 65 0246432 50 5 50

M10 x 80 0246440 50 16 50

M10 x 95 0246447 50 32 50

M10 x 115 0246453 50 52 50

M10 x 130 0246456 50 67 50

M12 x 80 0246540 60 5 50

M12 x 100 0246550 60 24 50

M12 x 120 0246554 60 44 50

M12 x 135 0246557 60 58 50

M12 x 150 0246560 60 73 50

M12 x 180 0246566 60 105 50

M12 x 235 0246573 60 160 50

M16 x 105 0246651 80 5 25

M16 x 140 0246658 80 40 25

M16 x 180 0246666 80 80 25

M16 x 220 0246672 80 120 25

M16 x 280 0246678 80 180 15

M20 x 125 0246755 100 5 25

M20 x 160 0246762 100 40 25 494.50

M20 x 200 0246770 100 80 10

M20 x 300 0246780 100 180 10

M24 x 180 0246866 120 35 10

M24 x 260 0246876 120 115 10

SIZE MF HOLE MAX.FIX. BOX PRICE CODE DEPTH* THICKNESS QTY. PER 100

* Minimum recommended hole depth in concrete of 25N/mm2 strength.

In weaker concrete embedment should be deeper.

Throughbolts should not be used in brickwork or aggregate blocks.

These short Throughbolts have reduced embedment depths. Load and torque figures should be reduced accordingly; tighten to 5 full turns from finger tight.

We do not recommend short Throughbolts to be used as structural load fixings.

Throughbolt is a versatile, cost effective anchor, combining ease of installation with good load carrying characteristics. It requires a hole the same diameter as the bolt and so is ideal for through fixing. For use in concrete with minimum strength of 20N/mm2 .

TEL: (0115) 922 1585

WIREHANGERS Simple effective fixing for wire suspension from concrete ceilings

M 6 0251006 - hole: 6mm x 40mm Boxed in 100’s 19.20


GENERAL FIXINGS

Throughbolts OCTOBER 2010

THROUGHBOLTS– STAINLESS STEEL

M6 x 70 0248235 30mm 10mm 100 130.60

M8 x 80 0248340 40 30 50 180.00

M8 x 95 0248347 40 43 50 200.00

M8 x 115 0248353 40 63 50 279.95

M10 x 75 0248438 50 10 50 285.00

M10 x 90 0248445 50 15 50 313.60

M10 x 125 0248455 50 50 20 435.00

M12 x 80 0248540 60 5 50 385.00

M12 x 115 0248553 60 15 20 495.00

M12 x 145 0248559 60 45 20 595.00

M16 x 110 0248652 80 10 10 980.00

M16 x 145 0248659 80 25 10 990.00

M16 x 170 0248664 80 50 10 1195.85

M20 x 125 0248755 100 5 25 2666.00

M20 x 160 0248762 100 40 25 3109.80

M20 x 200 0248770 100 80 10 3695.60

M20 x 300 0248780 100 180 10 5289.10

M24 x 260 0248876 120 115 10 6830.80

SIZE MF HOLE MAX.FIX. BOX PRICE CODE DEPTH THICKNESS QTY. PER 100

Stainless Steel Grade A4–316

THROUGHBOLTS– HOT DIP GALVANISED

M8 x 65 0247333 40 15 50 61.15

M8 x 80 0247340 40 30 50 62.10

M8 x 95 0247347 40 45 50 79.90

M10 x 60 0247430 50 5 50 90.85

M10 x 80 0247440 50 20 50 96.00

M10 x 95 0247447 50 35 50 104.05

M10 x 115 0247453 50 55 25 118.35

M10 x 130 0247456 50 70 25 125.30

M10 x 160 0247462 50 80 25 154.60

M12 x 80 0247540 60 10 25 144.55

M12 x 100 0247550 60 30 25 157.35

M12 x 120 0247554 60 50 25 171.25

M12 x 145 0247559 60 50 25 201.45

M12 x 185 0247567 60 90 25 236.80

M16 x 105 0247651 80 10 20 289.70

M16 x 140 0247658 80 45 10 351.95

M16 x 180 0247666 80 85 10 402.50

M20 x 160 0247762 100 30 20 579.15

TEL: (0115) 922 1585

WIREHANGERS Simple effective fixing for wire suspension from concrete ceilings

M 6 0251006 - hole: 6mm x 40mm Boxed in 100’s


GENERAL FIXINGS

Throughbolts OCTOBER 2010

THROUGHBOLTS– STAINLESS STEEL

M6 x 70 0248235 30mm 10mm 100

M8 x 80 0248340 40 30 50

M8 x 95 0248347 40 43 50

M8 x 115 0248353 40 63 50 279.95

M10 x 75 0248438 50 10 50

M10 x 90 0248445 50 15 50

M10 x 125 0248455 50 50 20

M12 x 80 0248540 60 5 50

M12 x 115 0248553 60 15 20

M12 x 145 0248559 60 45 20

M16 x 110 0248652 80 10 10

M16 x 145 0248659 80 25 10

M16 x 170 0248664 80 50 10

M20 x 125 0248755 100 5 25 2666.00

M20 x 160 0248762 100 40 25 3109.80

M20 x 200 0248770 100 80 10 3695.60

M20 x 300 0248780 100 180 10 5289.10

M24 x 260 0248876 120 115 10 6830.80

SIZE MF HOLE MAX.FIX. BOX PRICE CODE DEPTH THICKNESS QTY. PER 100

Stainless Steel Grade A4–316

THROUGHBOLTS– HOT DIP GALVANISED

M8 x 65

M8 x 80

M8 x 95

M10 x 60

M10 x 80

M10 x 95

M10 x 115

M10 x 130

M10 x 160

M12 x 80

M12 x 100

M12 x 120

M12 x 145

M12 x 185

M16 x 105

M16 x 140

M16 x 180

M20 x 160

0247333 40 15 50 0247333 40 15 50 0247333 40 15 50 0247333 40 15 50

0247340 40 30 50 0247340 40 30 50 0247340 40 30 50 0247340 40 30 50

0247347 40 45 50 0247347 40 45 50 0247347 40 45 50 0247347 40 45 50

0247430 50 5 50 0247430 50 5 50 0247430 50 5 50 0247430 50 5 50

0247440 50 20 50 0247440 50 20 50 0247440 50 20 50 0247440 50 20 50

0247447 50 35 50 0247447 50 35 50 0247447 50 35 50 0247447 50 35 50

0247453 50 55 25 0247453 50 55 25 0247453 50 55 25 0247453 50 55 25

0247456 50 70 25 10247456 50 70 25 10247456 50 70 25 10247456 50 70 25 1

0247462 50 80 25 0247462 50 80 25 0247462 50 80 25 0247462 50 80 25

0247540 60 10 25 0247540 60 10 25 0247540 60 10 25 0247540 60 10 25

0247550 60 30 25 0247550 60 30 25 0247550 60 30 25 0247550 60 30 25

0247554 60 50 25 0247554 60 50 25 0247554 60 50 25 0247554 60 50 25

0247559 60 50 25 201.450247559 60 50 250247559 60 50 250247559 60 50 25

0247567 60 90 25 0247567 60 90 25 0247567 60 90 25 0247567 60 90 25

0247651 80 10 20 0247651 80 10 20 0247651 80 10 20 0247651 80 10 20

0247658 80 45 10 0247658 80 45 10 0247658 80 45 10 0247658 80 45 10

0247666 80 85 10 0247666 80 85 10 0247666 80 85 10 0247666 80 85 10

0247762 100 30 20 579.15

TEL: (0115) 922 1585

DP 06040P 0256220 6mm 38mm 8mm 100 29.45

DP 12125P 0256555 12 126 74 20 125.00

DP 16140P 0256658 16 140 83 10 211.15

DP 20080P 0256740 20 81 20 10 246.55

DP 20115P 0256753 20 113 52 5 292.90

DP 20160P 0256762 20 157 96 5 360.10


GENERAL FIXINGS

Sleeve Anchors OCTOBER 2010

HEXAGON BOLT TYPE

DP 08045H 0255322 8mm 45mm 8mm 100 36.60

DP 08070H 0255335 8 72 30 50 44.45

DP 08095H 0255347 8 98 55 50 58.90

DP 10055H 0255427 10 55 14 50 49.55

DP 10080H 0255440 10 80 35 50 58.05

DP 10105H 0255451 10 108 60 25 78.40

DP 12065H 0255532 12 60 12 25 78.00

DP 12075H 0255537 12 75 18 25 80.65

DP 12105H 0255551 12 102 46 20 107.00

DP 16070H 0255635 16 63 12 20 125.05

DP 16110H 0255652 16 107 49 10 176.30

PRODUCT MF SLEEVE/ OVERALL MAX. FIX. BOX PRICE CODE CODE HOLE DIA. LENGTH THICKNESS QTY PER 100


DP 08060F 0257330 8mm 63mm 27mm 100 66.00

DP 08085F 0257342 8 89 53 50 74.30

DP 10075F 0257437 10 76 35 50 82.85

DP 10100F 0257450 10 103 62 50 97.90


HEXAGON NUT TYPE

COUNTERSUNK HEAD

• Light duty all metal anchor for general fixing into brickwork, concrete and blockwork of above 7N/mm2 strength. FOR STAINLESS STEEL SEE THE MF STAINLESS CATALOGUE

TEL: (0115) 922 1585

Stock sizes priced in bold

DP 06040P 0256220 6mm 38mm 8mm 100

DP 12125P 0256555 12 126 74 20

DP 16140P 0256658 16 140 83 10

DP 20080P 0256740 20 81 20 10

DP 20115P 0256753 20 113 52 5

DP 20160P 0256762 20 157 96 5


GENERAL FIXINGS

Sleeve Anchors OCTOBER 2010

HEXAGON BOLT TYPE

DP 08045H 0255322 8mm 45mm 8mm 100

DP 08070H 0255335 8 72 30 50

DP 08095H 0255347 8 98 55 50

DP 10055H 0255427 10 55 14 50

DP 10080H 0255440 10 80 35 50

DP 10105H 0255451 10 108 60 25

DP 12065H 0255532 12 60 12 25

DP 12075H 0255537 12 75 18 25

DP 12105H 0255551 12 102 46 20

DP 16070H 0255635 16 63 12 20

DP 16110H 0255652 16 107 49 10



DP 08060F 0257330 8mm 63mm 27mm 100 66.00

DP 08085F 0257342 8 89 53 50 74.30

DP 10075F 0257437 10 76 35 50

DP 10100F 0257450 10 103 62 50


HEXAGON NUT TYPE

COUNTERSUNK HEAD

• Light duty all metal anchor for general fixing into brickwork, concrete and blockwork of above 7N/mm2 strength. FOR STAINLESS STEEL SEE THE MF STAINLESS CATALOGUE

TEL: (0115) 922 1585

Stock sizes priced in bold

M8 0265352 110mm 20mm 10 65.00 80.00 268.00

M10 0265456 130 30 10 84.75 113.35 408.00

M12 0265562 160 35 10 145.00 146.70 540.00

M16 0265668 190 45 10 247.60 293.35 1076.00

M20 0265776 260 65 10 470.00 693.35 2184.00

M24 0265880 300 65 10 710.00 1071.60 3439.20


GENERAL FIXINGS

Chemical Anchors - FISCHER / RAWLPLUG OCTOBER 2010

CAPSULES

CM08 0263008 10mm 80mm 10 128.76

CM10 0263010 12 90 10 136.00

CM12 0263012 14 120 10 150.00

CM16 0263016 18 125 10 220.00

CM20 0263020 25 170 10 308.00

CM24 0263024 28 210 10 470.00

SIZE MF HOLE HOLE BOX PRICE CODE SIZE DEPTH QUANTITY PER 100

STUDS

SIZE MF LENGTH MAX. FIXING BOX BZP GALV S/STEEL CODE THICKNESS QUANTITY GRADE 5.8 GRADE 5.8 A4

HAC HAMMER IN CAPSULES

HAC08 0264008 10mm 80mm 10 142.50

HAC10 0264010 12 100 10 156.25

HAC12 0264012 14 120 10 163.15

HAC16 0264016 18 160 10 197.60

HAC20 0264020 25 200 6 366.70

HAC24 0264024 28 240 6 447.95


• For use with stud or rebar. Set by simply hammering through the capsule.• Allows for use of standard studding cut to length.

02670265 0269

Including nut and washer

• All studs have hexagonal drive head and come complete with simple setting tool for driving into CM capsules.• Can be used with cartridge resin.

• The capsule is broken and mixed in the hole by the action of driving the stud in with a drilling machine.

• High performance resin bonded anchor system for use in a variety of solid substrates. These anchors do not expand and therefore provide an expansion stress free fixing.

PRICE PER 100

M6 x 24 0270212 75 M10 10 90.45 306.30

M8 x 25 0270316 90 M12 10 96.55 298.10

M10 x 40 0270420 100 M16 10 185.40 515.50

M12 x 48 0270524 100 M16 6 207.00 796.00

M16 x 64 0270632 125 M24 6 398.00 1789.70

INTERNAL THREADED SOCKETS

THREAD SIZE MF SOCKET CAPSULE BOX PRICE PER 100DIA x LGTH MM CODE LENGTH SIZE QUANTITY M/STEEL S/STEEL A2

• Internally threaded sockets for use with capsules.

0270 0271

TEL: (0115) 922 1585

Pleasecontactus forprices


M8 0265352 110mm 20mm 10

M10 0265456 130 30 10

M12 0265562 160 35 10

M16 0265668 190 45 10

M20 0265776 260 65 10

M24 0265880 300 65 10

© MIDLAND FIXINGS 20101 / 121 / 12

GENERAL FIXINGS

Chemical Anchors - FISCHER / RAWLPLUG OCTOBER 2010

CAPSULES

CM08 0263008 10mm 80mm 10

CM10 0263010 12 90 10

CM12 0263012 14 120 10

CM16 0263016 18 125 10

CM20 0263020 25 170 10

CM24 0263024 28 210 10


STUDS

SIZE MF LENGTH MAX. FIXING BOX BZP GALV S/STEEL CODE THICKNESS QUANTITY GRADE 5.8 GRADE 5.8 A4

HAC HAMMER IN CAPSULES

HAC08

HAC10

HAC12

HAC16

HAC20

HAC24


0264008 10mm 80mm 10 0264008 10mm 80mm 10 0264008 10mm 80mm 10 0264008 10mm 80mm 10

0264010 12 100 10 0264010 12 100 10 0264010 12 100 10 0264010 12 100 10

0264012 14 120 10 0264012 14 120 10 0264012 14 120 10 0264012 14 120 10

0264016 18 160 10 0264016 18 160 10 0264016 18 160 10 0264016 18 160 10

0264020 25 200 6 0264020 25 200 6 0264020 25 200 6 0264020 25 200 6

0264024 28 240 6 0264024 28 240 6 0264024 28 240 6 0264024 28 240 6

• For use with stud or rebar. Set by simply hammering through the capsule.• Allows for use of standard studding cut to length.

02670265 0269

Including nut and washer

• All studs have hexagonal drive head and come complete with simple setting tool for driving into CM capsules.• Can be used with cartridge resin.

• The capsule is broken and mixed in the hole by the action of driving the stud in with a drilling machine.

• High performance resin bonded anchor system for use in a variety of solid substrates. These anchors do not expand and therefore provide an expansion stress free fixing.

PRICE PER 100

M6 x 24 0270212 75 M10 10

M8 x 25 0270316 90 M12 10

M10 x 40

M12 x 48

M16 x 64

0270212 75 M10 10

0270316 90 M12 10

0270420 100 M16 10

0270524 100 M16 6

0270632 125 M24 6 398.00

INTERNAL THREADED SOCKETS

THREAD SIZE MF SOCKET CAPSULE BOX PRICE PER 100DIA x LGTH MM CODE LENGTH SIZE QUANTITY M/STEEL S/STEEL A2

• Internally threaded sockets for use with capsules.

0270 0271

TEL: (0115) 922 1585




GENERAL FIXINGS

Chemical Anchors APRIL 2010

• Injection Resins are ideal for stress free fixing into a very wide range of substrates. This includes fixing into perforated materials, in conjunction with mesh sleeves, and aircrete blocks in conjunction with Cone Drills. These quality mix-in-the-nozzle resins are versatile, straight-forward and safe to use.

SPARE MIXER NOZZLES

POLYESTER RESINS

PRODUCT MF DESCRIPTION SUITABLE FOR PRICE CODE CODE EACH SMN 0276210 Spare Mixer Nozzles Universal for all Standard Resins 1.50

FIS SE 0276230 Spare Mixer Nozzles FIS EM 390S Only 4.35

FIS EN 0276290 1m Extension Nozzles Extensions for all Nozzles 5.61

KEM 380 0273238 Polyester Resin 380ml FIP 10 13.00

KEM 300 0273230 Polyester Resin* 300ml MASTIC 10 12.50

RESIN CARTRIDGE GUNS PRODUCT MF DESCRIPTION SUITS RESIN CARTRIDGE PRICE CODE CODE EACH FIP 0276010 Resin Cartridge Gun KEM 380 22.90

FIS AM 0276020 Resin Cartridge Gun FIS V 360S 30.80

FIS AK 0276030 Resin Cartridge Gun FIS V 360S / FIS EM 390S 90.00

RESIN SITE BOXES PRODUCT MF CONTENTS PRICE CODE CODE EACH FIPC - SB 0276115 Site Box, FIP Gun, Brush Set, Dust Pump, 5 Nozzles 92.50

FISV - SB 0276125 Site Box, FIS AM Gun, Brush Set, Dust Pump, 5 Nozzles 90.00

TEL: (0115) 922 1585

• Suitable for use in all masonry building materials• For use in concrete in non-critical applications

• High performance resins for use in concrete and all common building substrates• Give maximum loadings with maintained bond strength even in damp conditions• Hybrid versions have cement element for maximum performance and stability and are suitable alternative to HILTI HY150

• Epoxy resin is characterised by extremely high bond strength and excellent adhesion• Especially suited for smooth, diamond drilled holes and shallow embedment depths• Can be used in damp conditions and even under water

* Styrene free

FISCHER VINYLESTER RESINS

FIS VS 300T 0274130 Hybrid Vinylester Resin 300ml MASTIC 12 18.15

FIS V 360S 0274136 Hybrid Vinylester Resin 360ml FIS AM 6 25.90

PRODUCTCODE

PRODUCTCODE

MFCODE

MFCODE

DESCRIPTION

DESCRIPTION

SIZE

SIZE

GUN TOSUIT

GUN TOSUIT

BOXQTY

BOXQTY

PRICEEACH

PRICEEACH

FISCHER EPOXY RESIN

FIS EM 390S 0275139 Epoxy Resin Cartridge 390ml FIS AK 6 33.00

PRODUCTCODE

MFCODE DESCRIPTION SIZE

GUN TOSUIT

BOXQTY

PRICEPER EACH


GENERAL FIXINGS

Chemical Anchors APRIL 2010

• Injection Resins are ideal for stress free fixing into a very wide range of substrates. This includes fixing into perforated materials, in conjunction with mesh sleeves, and aircrete blocks in conjunction with Cone Drills. These quality mix-in-the-nozzle resins are versatile, straight-forward and safe to use.

SPARE MIXER NOZZLES

POLYESTER RESINS

PRODUCT MF DESCRIPTION SUITABLE FOR PRICE CODE CODE EACH SMN 0276210 Spare Mixer Nozzles Universal for all Standard Resins

FIS SE 0276230 Spare Mixer Nozzles FIS EM 390S Only

FIS EN 0276290 1m Extension Nozzles Extensions for all Nozzles

KEM 380

KEM 300

RESIN CARTRIDGE GUNS PRODUCT MF DESCRIPTION SUITS RESIN CARTRIDGE PRICE CODE CODE EACH FIP 0276010 Resin Cartridge Gun KEM 380

FIS AM 0276020 Resin Cartridge Gun FIS V 360S

FIS AK 0276030 Resin Cartridge Gun FIS V 360S / FIS EM 390S

Polyester Resin 380ml FIP 10 Polyester Resin 380ml FIP 10 Polyester Resin 380ml FIP 10 Polyester Resin 380ml FIP 10 0273238

Polyester Resin* 300ml MASTIC 10 Polyester Resin* 300ml MASTIC 10 Polyester Resin* 300ml MASTIC 10 Polyester Resin* 300ml MASTIC 10 0273230

RESIN SITE BOXES PRODUCT MF CONTENTS PRICE CODE CODE EACH FIPC - SB 0276115 Site Box, FIP Gun, Brush Set, Dust Pump, 5 Nozzles

FISV - SB 0276125 Site Box, FIS AM Gun, Brush Set, Dust Pump, 5 Nozzles

TEL: (0115) 922 1585

• Suitable for use in all masonry building materials• For use in concrete in non-critical applications

• High performance resins for use in concrete and all common building substrates• Give maximum loadings with maintained bond strength even in damp conditions• Hybrid versions have cement element for maximum performance and stability and are suitable alternative to HILTI HY150

• Epoxy resin is characterised by extremely high bond strength and excellent adhesion• Especially suited for smooth, diamond drilled holes and shallow embedment depths• Can be used in damp conditions and even under water

* Styrene free

FISCHER VINYLESTER RESINS

FIS VS 300T 0274130 Hybrid Vinylester Resin 300ml MASTIC 12 18.15

FIS V 360S 0274136 Hybrid Vinylester Resin 360ml FIS AM 6 25.90

PRODUCTCODE

PRODUCTCODE

MFCODE

MFCODE

DESCRIPTION

DESCRIPTION

SIZE

SIZE

GUN TOSUIT

GUN TOSUIT

BOXQTY

BOXQTY

FISCHER EPOXY RESIN

FIS EM 390S 0275139 Epoxy Resin Cartridge 390ml FIS AK 6 33.00

PRODUCTCODE

MFCODE DESCRIPTION SIZE

GUN TOSUIT

BOXQTY

Chemical Anchors OCTOBER 2010


GENERAL FIXINGS

HOLE CLEANING ACCESSORIES

PRODUCT MF DESCRIPTION PRICE CODE CODE EACH ABG 0276301 Dust Pump 22.40

BR1 0276310 Cleaning Brush M8 - 10 Holes 4.75



Thorough hole cleaning is essential to successful resin fixing in solid materials. Recommended method is: blow out at least twice, brush out twice and blow out twice again. A badly cleaned hole means reduced load values.

AIRCRETE RESIN SYSTEM

PRODUCT MF DESCRIPTION PRICE CODE CODE PBB 0279300 Fischer Cone Drill 47.73 each

PBZ 0279400 Fischer Centring Sleeve 72.27 per 100

For optimum performance into lightweight blocks and other similar materials. Special cone drill cuts a conical undercut hole which is filled with resin. Plastic centring sleeve holds the anchor central while the resin hardens.

PUMP IN RESIN STUDS PRODUCT MF CODE CODE 100 120 150 180 200 300 M8 02773 30.20 45.00 52.20 60.45 65.95 129.40

M10 02774 38.10 60.10 69.70 75.20 92.80 159.00

M12 02775 - 120.90 143.90 169.90 187.40 207.40

M16 02776 - - 227.25 - 255.50 338.50

M20 02777 - - - - 333.75 493.75

M24 02778 - - - - - 664.75

LENGTH /PRICE PER 100

PUMP IN RESIN SOCKETS PRODUCT MF DESCRIPTION DRILL INTERNAL PRICE CODE CODE DIA. THREAD DEPTH PER 100 M8 x 80 0278342 Pump In Resin Sockets 14 35 141.10

M10 x 80 0278442 Pump In Resin Sockets 16 40 144.95

For resin fixing into perforated or hollow materials. The sleeve is inserted into the hole and filled with resin. The anchor is then pushed into the sleeve. In the case of Mesh Sleeves the resin is displaced through the mesh, with Net Sleeves the resin remains within the net and the complete net expands in the void.

PUMP IN RESIN SLEEVES

SIZE MF DESCRIPTION SUITS STUD DRILL PRICE CODE SIZE DIA. PER 100 16 x 80 0279640 Plastic Mesh Sleeves M8 / 10 16 41.60

16 x 130 0279656 Plastic Mesh Sleeves M8 / 10 16 49.40

20 x 85 0279742 Plastic Mesh Sleeves M12 / 16 20 70.70

*Cut on site to required length

PRICE EACH

16 x 1000 0280695 Metal Mesh Sleeves* M8 / 10 16 9.70

22 x 1000 0280795 Metal Mesh Sleeves* M12 / 16 22 11.05

PRICE PER 100 FIS H 18x85N 0279185 Fischer Net Sleeves M10 18 164.26

FIS H 20x85N 0279285 Fischer Net Sleeves M12 20 198.36

TEL: (0115) 922 1585


Chemical Anchors OCTOBER 2010


GENERAL FIXINGS

HOLE CLEANING ACCESSORIES

PRODUCT MF DESCRIPTION PRICE CODE CODE EACH ABG 0276301 Dust Pump

BR1 0276310 Cleaning Brush M8 - 10 Holes



Thorough hole cleaning is essential to successful resin fixing in solid materials. Recommended method is: blow out at least twice, brush out twice and blow out twice again. A badly cleaned hole means reduced load values.

AIRCRETE RESIN SYSTEM

PRODUCT MF DESCRIPTION PRICE CODE CODE PBB 0279300 Fischer Cone Drill

PBZ 0279400 Fischer Centring Sleeve

For optimum performance into lightweight blocks and other similar materials. Special cone drill cuts a conical undercut hole which is filled with resin. Plastic centring sleeve holds the anchor central while the resin hardens.

PUMP IN RESIN STUDS PRODUCT MF CODE CODE 100 120 150 180 200 300 M8 02773 30.20 45.00 52.20 60.45 65.95 129.40

M10 02774 38.10 60.10 69.70 75.20 92.80 159.00

M12 02775 - 120.90 143.90 169.90 187.40 207.40

M16 02776 - - 227.25 - 255.50 338.50

M20 02777 - - - - 333.75 493.75

M24 02778 - - - - - 664.75

LENGTH /PRICE PER 100

PUMP IN RESIN SOCKETS PRODUCT MF DESCRIPTION DRILL INTERNAL PRICE CODE CODE DIA. THREAD DEPTH PER 100 M8 x 80 0278342 Pump In Resin Sockets 14 35

M10 x 80 0278442 Pump In Resin Sockets 16 40

For resin fixing into perforated or hollow materials. The sleeve is inserted into the hole and filled with resin. The anchor is then pushed into the sleeve. In the case of Mesh Sleeves the resin is displaced through the mesh, with Net Sleeves the resin remains within the net and the complete net expands in the void.

PUMP IN RESIN SLEEVES

SIZE MF DESCRIPTION SUITS STUD DRILL PRICE CODE SIZE DIA. PER 100 16 x 80 0279640 Plastic Mesh Sleeves M8 / 10 16

16 x 130 0279656 Plastic Mesh Sleeves M8 / 10 16

20 x 85 0279742 Plastic Mesh Sleeves M12 / 16 20

*Cut on site to required length

PRICE EACH

16 x 1000 0280695 Metal Mesh Sleeves* M8 / 10 16

22 x 1000 0280795 Metal Mesh Sleeves* M12 / 16 22

PRICE PER 100 FIS H 18x85N 0279185 Fischer Net Sleeves M10 18

FIS H 20x85N 0279285 Fischer Net Sleeves M12 20

TEL: (0115) 922 1585



GENERAL FIXINGS

Non-expanding Anchors - 1 OCTOBER 2010

QWIK ANKERS

Self tapping multi-substrate anchors

• Qwik Ankers are suitable for fixing into numerous different substrates• Benefits of a non-expanding anchor are positive and safe anchorage over full embedment length of fixing, high pull-out loadings and close-to-edge fixing ability• Anchors can be easily removed if necessory

• Self tapping masonry screw for time saving installation of all types of window and door frames• Benefits are small hole diameter, high load bearing and importantly no distortion of frame profile• Also ideal for timber batten fixing and other general uses• Supplied in boxes of 100 c/w Torx bit

FRAME SCREWS

M6 x 50 0287225 6 8 20 30mm 33.20

M6 x 75 0287237 6 8 45 30mm 46.20

M7.5 x 35 0286035 6 8 5 30mm 37.50

M8 x 60 0287330 8 10 20 40mm 48.70

M8 x 75 0287337 8 10 35 40mm 64.05

M8 x 100 0287350 8 10 60 40mm 81.20

M10 x 60 0287430 10 12 10 50mm 83.45

M10 x 75 0287437 10 12 25 50mm 80.85

M10 x 100 0287450 10 12 10 50mm 115.30

M10 x 130 0287456 10 12 80 50mm 140.65

M10 x 150 0287460 10 12 100 50mm 158.95

M12 x 75 0287537 12 14 15 60mm 120.00

M12 x 100 0287550 12 14 40 60mm 152.85

M12 x 150 0287560 12 14 90 60mm 263.65

M12 x 200 0287570 12 14 140 60mm 339.50

M16 x 100 0287650 16 20 20 80mm 432.60

M16 x 150 0287660 16 20 70 80mm 568.10

M16 x 200 0287670 16 20 120 80mm 727.10

M6 x 50 0285225 6 8 20 30mm 27.65

M6 x 75 0285237 6 8 45 30mm 38.50

M6 x 100 0285250 6 8 55 45mm 49.10

M6 x 130 0285256 6 8 85 45mm 61.60

SIZE

HEXAGON

COUNTERSUNK TORX DRIVE

MFCODE

DRILLSIZEmm

CLEARANCESIZEmm

MAX FIXINGTHICKNESS

mm

MINIMUM EMBEDMENTDEPTH

mm

PRICEPER100

7.5 X 50 0289050 6.0mm masonry / 6.5mm concrete 11.70

7.5 X 60 0289060 “ “ 13.30

7.5 X 80 0289080 “ “ 16.45

7.5 X 100 0289100 “ “ 19.85

7.5 X 120 0289120 “ “ 25.40

7.5 X 150 0289150 “ “ 31.55

7.5 x 180 0289180 “ “ 39.70

7.5 x 202 0289202 “ “ 42.60

7.5 x 212 0289212 “ “ 48.90

White 0289750 Cover Caps to suit 2.60

CODEMF

CODE DRILL SIZEPRICE

PER 100


GENERAL FIXINGS

Non-expanding Anchors - 1 OCTOBER 2010

QWIK ANKERS

Self tapping multi-substrate anchors

• Qwik Ankers are suitable for fixing into numerous different substrates• Benefits of a non-expanding anchor are positive and safe anchorage over full embedment length of fixing, high pull-out loadings and close-to-edge fixing ability• Anchors can be easily removed if necessory

• Self tapping masonry screw for time saving installation of all types of window and door frames• Benefits are small hole diameter, high load bearing and importantly no distortion of frame profile• Also ideal for timber batten fixing and other general uses• Supplied in boxes of 100 c/w Torx bit• Supplied in boxes of 100 c/w Torx bit

FRAME SCREWS

M6 x 50 0287225 6 8 20 30mm

M6 x 75 0287237 6 8 45 30mm

M7.5 x 35 0286035 6 8 5 30mm

M8 x 60 0287330 8 10 20 40mm

M8 x 75 0287337 8 10 35 40mm

M8 x 100 0287350 8 10 60 40mm

M10 x 60 0287430 10 12 10 50mm

M10 x 75 0287437 10 12 25 50mm

M10 x 100 0287450 10 12 10 50mm

M10 x 130 0287456 10 12 80 50mm

M10 x 150 0287460 10 12 100 50mm

M12 x 75 0287537 12 14 15 60mm

M12 x 100 0287550 12 14 40 60mm

M12 x 150 0287560 12 14 90 60mm

M12 x 200 0287570 12 14 140 60mm

M16 x 100 0287650 16 20 20 80mm

M16 x 150 0287660 16 20 70 80mm

M16 x 200 0287670 16 20 120 80mm

M6 x 50 0285225 6 8 20 30mm

M6 x 75 0285237 6 8 45 30mm

M6 x 100 0285250 6 8 55 45mm

M6 x 130 0285256 6 8 85 45mm

SIZE

HEXAGON

COUNTERSUNK TORX DRIVE

MFCODE

DRILLSIZEmm

CLEARANCESIZEmm

MAX FIXINGTHICKNESS

mm

MINIMUM EMBEDMENTDEPTH

mm

7.5 X 50 0289050 6.0mm masonry / 6.5mm concrete

7.5 X 60 0289060 “ “ 13.30

7.5 X 80 0289080 “ “ 16.45

7.5 X 100 0289100 “ “ 19.85

7.5 X 120 0289120 “ “ 25.40

7.5 X 150 0289150 “ “ 31.55

7.5 x 180 0289180 “ “ 39.70

7.5 x 202 0289202 “ “

7.5 x 212 0289212 “ “

White 0289750 Cover Caps to suit 2.60

CODEMF

CODE DRILL SIZE

TEL: (0115) 922 1585


SCREWS, NAILS, STAPLES & RIVETS

Non-expanding Anchors - 2 JANUARY 2010


HEXAGONWASHER HEAD

PHILLIPSCSK HEAD

MFCODE

MFCODE

BOXQUANTITY

PRICEPER 100

TAPCON MASONRY ANCHORS

5C32 0291116 5H32 0292116 1000 12.77

5C45 0291122 5H45 0292122 1000 13.98

5C57 0291128 5H57 0292128 1000 15.50

5C70 0291135 500 16.41

5C82 0291141 500 17.93

5C100 0291150 500 20.07

6C32 0291216 6H32 0292216 1000 15.81

6C45 0291222 6H45 0292222 1000 18.24

6C57 0291228 6H57 0292228 500 20.66

6C70 0291235 6H70 0292235 1000 22.51

6C82 0291241 6H82 0292241 500 24.31

6C100 0291250 6H100 0292250 500 27.06

6C125 0291255 500 56.22

• Tapcon is the original self-tapping masonry anchor for fastening a wide range of components to concrete, brick and masonry materials• Advantages are - fast installation - expansion free close to edge fixing - high performance

- shallow embedment, 25mm in concrete• Available in two diameters - 5.0mm or 6.0mm• Available in Countersunk or Hexagon Head

3SH180 0295180 4.35 dia. for 5.0mm dia anchors 180 32, 45, 57, 70, 82,100 6.45


4SH205 0296205 5.15 dia. for 6.0mm dia anchors 205 125 14.95

DRILLCODE

MFCODE

• All Tapcon drills are made to the close tolerances required to provide the best performance of the anchors

DIAMETER LENGTH MMTO SUIT ANCHOR

LENTHS (MM)PRICEEACH

SDS - TAPCON DRILLS

Drill pilot hole through fixture into concrete Snap on drive sleeve

Drive anchorJOB COMPLETE

INSTALLATION INSTRUCTIONS

TAPCON TOOLS AND ACCESSORIES

CONDRIVE 1000

P2P3

DRILL BIT

CD110

CD101

AK8

CD102 ASSYCD1022

SDS DRILL BIT

PRODUCT MF PRICE CODE CODE DESCRIPTION EACH

CD1000 0297100 Condrive Kit complete for installing all Tapcon Anchors (kit comprises * items below) 31.25

CD101* 0297101 Drill Bit Holder 7.89

CD102* 0297102 Standard Drive Sleeve 9.70

CD106* 0297106 1/4” Hex Socket (For type 5H Tapcon) 3.95

CD107* 0297107 5/16” Hex Socket (For type 6H Tapcon) 4.55

CD110* 0297110 Phillips Drive Adaptor 7.90

P2* 2385201 Phillips Bit (5.0mm Csk) 0.50

P3* 2385301 Phillips Bit (6.0mm Csk) 0.50

AK8* 0297108 Hex Key 0.61



SCREWS, NAILS, STAPLES & RIVETS1 / 161 / 161 / 11 / 161 / 11 / 11 / 161 / 1

GENERAL FIXINGSSCREWS, NAILS, STAPLES & RIVETSGENERAL FIXINGSSCREWS, NAILS, STAPLES & RIVETS

HEXAGONWASHER HEAD

PHILLIPSCSK HEAD

MFCODE

MFCODE

BOXQUANTITY

TAPCON MASONRY ANCHORS

5C32 0291116 5H32 0292116 1000

5C45 0291122 5H45 0292122 1000

5C57 0291128 5H57 0292128 1000

5C70 0291135 500

5C82 0291141 500

5C100 0291150 500

6C32 0291216 6H32 0292216 1000

6C45 0291222 6H45 0292222 1000

6C57 0291228 6H57 0292228 500

6C70 0291235 6H70 0292235 1000

6C82 0291241 6H82 0292241 500

6C100 0291250 6H100 0292250 500

6C125 0291255 500

• Tapcon is the original self-tapping masonry anchor for fastening a wide range of components to concrete, brick and masonry materials• Advantages are - fast installation - expansion free close to edge fixing - high performance

- shallow embedment, 25mm in concrete• Available in two diameters - 5.0mm or 6.0mm• Available in Countersunk or Hexagon Head



4SH205 0296205 5.15 dia. for 6.0mm dia anchors 205 125 14.95

DRILLCODE

MFCODE

• All Tapcon drills are made to the close tolerances required to provide the best performance of the anchors

DIAMETER LENGTH MMTO SUIT ANCHOR

LENTHS (MM)

SDS - TAPCON DRILLS

Drill pilot hole through fixture into concrete Snap on drive sleeve

Drive anchorJOB COMPLETE

INSTALLATION INSTRUCTIONS

TAPCON TOOLS AND ACCESSORIES

CONDRIVE 1000CONDRIVE 1000

P2P2P3P3

DRILL BIT DRILL BIT

CD110

CD101

AK8

CD102 ASSYCD102 ASSYCD1022CD1022

SDS DRILL BITSDS DRILL BIT

PRODUCT MF PRICE CODE CODE DESCRIPTION EACH

CD1000 0297100 Condrive Kit complete for installing all Tapcon Anchors (kit comprises * items below)

CD101* 0297101 Drill Bit Holder

CD102* 0297102 Standard Drive Sleeve

CD106* 0297106 1/4” Hex Socket (For type 5H Tapcon)

CD107* 0297107 5/16” Hex Socket (For type 6H Tapcon)

CD110* 0297110 Phillips Drive Adaptor

P2* 2385201 Phillips Bit (5.0mm Csk)

P3* 2385301 Phillips Bit (6.0mm Csk)

AK8* 0297108 Hex Key

TEL: (0115) 922 1585

© MIDLAND FIXINGS 2010



• Short anchor length for shallow embedment• Good load capability e.g. QRH10 290kg Safe Load in B35 Concrete

QWIKIES

QRH 06 0293006 M6 6.5 mm 28 mm 39.40

QRH 08 0293008 M8 6.5 mm 38 mm 49.80

QRH 10 0293010 M10 6.5 mm 38 mm 55.00

QDS 12 0293112 Qwikie Drive Socket (for M8 & M10) 6.95

• For hanging threaded rods from concrete ceilings including hollow floor slabs• Non expanding - can be fixed close to edge and at closer centres than other anchors• Install in less than half the time of drop-in anchors using smaller diameter drill bits

THREADED ROD HANGERS

PRODUCTCODE

PRODUCTCODE

MFCODE

MFCODE

THREADSIZE

DESCRIPTION

DRILLDIAMETER

ANCHORLENGTH

PRICEPER 100

PRICEEACH

• M8/M10 dual threaded for flexibility • For installation use drive socket MOP13 (see page 9/5)

FISCHER FBS 6 M8/M10i

FBS 6 M8/M10I 0294810 6.0/6.5 mm 55 mm 60 mm 67.20

PRODUCTCODE

MFCODE

DRILLSIZE

ANCHORLENGTH

HOLEDEPTH

PRICEPER 100



1 / 171 / 17GENERAL FIXINGS

• Short anchor length for shallow embedment• Good load capability e.g. QRH10 290kg Safe Load in B35 Concrete

QWIKIES

QRH 06 0293006 M6 6.5 mm 28 mm

QRH 08 0293008 M8 6.5 mm 38 mm

QRH 10 0293010 M10 6.5 mm 38 mm

QDS 12 0293112 Qwikie Drive Socket (for M8 & M10)

• For hanging threaded rods from concrete ceilings including hollow floor slabs• Non expanding - can be fixed close to edge and at closer centres than other anchors• Install in less than half the time of drop-in anchors using smaller diameter drill bits

THREADED ROD HANGERS

PRODUCTCODE

PRODUCTCODE

MFCODE

MFCODE

THREADSIZE

DESCRIPTION

DRILLDIAMETER

ANCHORLENGTH

• M8/M10 dual threaded for flexibility • For installation use drive socket MOP13 (see page 9/5)

FISCHER FBS 6 M8/M10i

FBS 6 M8/M10I 0294810 6.0/6.5 mm 55 mm 60 mm

PRODUCTCODE

MFCODE

DRILLSIZE

ANCHORLENGTH

HOLEDEPTH

TEL: (0115) 922 1585


GENERAL FIXINGS

Cavity Fixings - 1 OCTOBER 2010

SPRING TOGGLES

M4 x 32 0305432 8mm 3-12mm M4 38mm 100 16.50

M4 x 38 0305438 “ 10-16 M4 45 “ 19.00

M5 x 37 0305537 11 6-13 M5 45 50 22.20

M5 x 52 0305552 “ 3-16 M5 58 “ 24.75

M5 x 65 0305565 “ 16-32 M5 72 “ 30.30

M6 x 37 0305637 13 6-13 M6 45 “ 29.20

M6 x 65 0305665 “ 14-32 M6 70 “ 37.50

UST 0305700 UNIVERSAL SETTING TOOL 1 18.95

METAL CAVITY FIXINGS High performance cavity fixing. Ideal for fixing radiators and heavy objects to plasterboard.

4100 0309410 8mm 0-2mm M4 20mm 50 36.25

4240 0309424 “ 6-14 M4 30 “ 36.60

5150 0309515 10 0-2 M5 20 “ 43.30

5250 0309525 “ 6-14 M5 30 “ 40.10

5400 0309540 “ 19-26 M5 50 “ 43.40

6150 0309615 13 0-2 M6 20 “ 50.55

6250 0309625 “ 3-13 M6 30 “ 59.75

6350 0309635 “ 13-23 M6 40 “ 60.70

8300 0309830 18 6-15 M8 40 “ 92.80

8500 0309850 “ 25-35 M8 60 “ 102.65

1055 0309955 20 25-35 M10 70 25 128.85

1275 0309975 24 33-45 M12 80 20 217.20

RAWLNUTS Problem solving fixing suitable for use in virtually any construction material, solid or hollow. Will fix into metal sheets, boards and also suitable for hollow pots, thin concrete slabs and tarmac.

M5 x 50 0301550 14mm 1-22mm M5 50mm 100 19.90

M6 x 75 0301675 18mm 1-45mm M6 60mm 50 27.10

For alternative screw lengths, see Machine Screws on page 7/12

PRODUCT MF DRILL BOARD SCREW MIN. BOX PRICE CODE CODE SIZE THICKNESS DIA. LGTH QTY. PER 100x

BM 5 0302005 13mm 9-90mm M5 25mm 50 65.70

BM 6 0302006 13mm 9-90mm M6 25mm 50 65.70

BM 8 0302008 19mm 9-90mm M8 25mm 25 115.50

SNAP TOGGLES • Vastly superior toggle fixing with high load - bearing capacity.• Much easier to install than spring toggles. Require smaller hole size and are self retained in wall - remain in place when

screw is removed.• Immense grip range - 9mm - 90mm

Includes screws


GENERAL FIXINGS

Cavity Fixings - 1 OCTOBER 2010

SPRING TOGGLES

M4 x 32 0305432 8mm 3-12mm M4 38mm 100

M4 x 38 0305438 “ 10-16 M4 45 “

M5 x 37 0305537 11 6-13 M5 45 50

M5 x 52 0305552 “ 3-16 M5 58 “

M5 x 65 0305565 “ 16-32 M5 72 “

M6 x 37 0305637 13 6-13 M6 45 “

M6 x 65 0305665 “ 14-32 M6 70 “

UST 0305700 UNIVERSAL SETTING TOOL 1

METAL CAVITY FIXINGS High performance cavity fixing. Ideal for fixing radiators and heavy objects to plasterboard.

4100 0309410 8mm 0-2mm M4 20mm 50

4240 0309424 “ 6-14 M4 30 “

5150 0309515 10 0-2 M5 20 “

5250 0309525 “ 6-14 M5 30 “

5400 0309540 “ 19-26 M5 50 “

6150 0309615 13 0-2 M6 20 “

6250 0309625 “ 3-13 M6 30 “

6350 0309635 “ 13-23 M6 40 “

8300 0309830 18 6-15 M8 40 “

8500 0309850 “ 25-35 M8 60 “

1055 0309955 20 25-35 M10 70 25

1275 0309975 24 33-45 M12 80 20

RAWLNUTS Problem solving fixing suitable for use in virtually any construction material, solid or hollow. Will fix into metal sheets, boards and also suitable for hollow pots, thin concrete slabs and tarmac.

M5 x 50 0301550 14mm 1-22mm M5 50mm 100

M6 x 75 0301675 18mm 1-45mm M6 60mm 50

For alternative screw lengths, see Machine Screws on page 7/12

PRODUCT MF DRILL BOARD SCREW MIN. BOX PRICE CODE CODE SIZE THICKNESS DIA. LGTH QTY. PER 100x PRODUCT MF DRILL BOARD SCREW MIN. BOX PRICEx PRODUCT MF DRILL BOARD SCREW MIN. BOX PRICE CODE CODE SIZE THICKNESS DIA. x CODE CODE SIZE THICKNESS DIA.

BM 5 0302005 13mm 9-90mm M5 25mm 50

BM 6 0302006 13mm 9-90mm M6 25mm 50

BM 8 0302008 19mm 9-90mm M8 25mm 25

0302005 13mm 9-90mm M5 25mm 50 0302005 13mm 9-90mm M5 25mm 50 0302005 13mm 9-90mm M5 25mm 50 0302005 13mm 9-90mm M5 25mm 50 0302005 13mm 9-90mm M5 25mm 50 0302005 13mm 9-90mm M5 25mm 50

0302006 13mm 9-90mm M6 25mm 50 0302006 13mm 9-90mm M6 25mm 50 0302006 13mm 9-90mm M6 25mm 50 0302006 13mm 9-90mm M6 25mm 50 0302006 13mm 9-90mm M6 25mm 50 0302006 13mm 9-90mm M6 25mm 50

0302008 19mm 9-90mm M8 25mm 25 0302008 19mm 9-90mm M8 25mm 25 0302008 19mm 9-90mm M8 25mm 25 0302008 19mm 9-90mm M8 25mm 25 0302008 19mm 9-90mm M8 25mm 25

SNAP TOGGLES • Vastly superior toggle fixing with high load - bearing capacity.• Much easier to install than spring toggles. Require smaller hole size and are self retained in wall - remain in place when

screw is removed.• Immense grip range - 9mm - 90mm

Includes screws

TEL: (0115) 922 1585


GENERAL FIXINGS

Cavity Fixings - 2 APRIL 2010

SPIT DRIVA PLUS • Heavy duty plasterboard fixing which is installed in the same way as the Driva, but has the advantage of a toggle for more substantial loads

FISCHER TYPE PD

QWIKMASTER • Expansion plug for plasterboard of any thickness. Made from tough glass filled nylon. For use with 6-10g woodscrews. Use Pozi Screwdrivers to punch hole in board first then drive Qwikmaster home

METAL DRIVA • Self drilling plasterboard fixing. Installed with a No.2 pozidriver • Comes complete with a 35mm Pan Head Screw

• High load capacity cavity fixing which is fast and easy to install in plasterboard and other board materials• Extra short expansion zone means PD can be installed with only the smallest cavity behind the board• Accommodates double board thicknesses

Suitable for chipboard screws only.

PD 8 0321008 8mm 6mm+ 4.0mm 40mm 100 18.35

PD 10 0321010 10mm 7mm+ 5.0mm 40mm 100 22.85

PD 12 0321012 12mm 9mm+ 6.0mm 40mm 100 26.95

TP12 0330012 - 10-16mm 8g 35mm 100 13.95

TP12 PLUS 0330110 - 10-13mm 8g 45mm 100 45.50

QM 28 0332028 - 10mm+ 6-10g 11⁄4 100 14.50

PRODUCT MF DRILL BOARD SCREW MIN. BOX PRICE CODE CODE SIZE THICKNESS DIA. LGTH QTY. PER 100x

FISCHER TYPE UX-R

13mm 0317013 8mm 13-16mm 8-12g 2” 100 15.30

POLYTOGGLE • Medium duty plasterboard fixing. stays in place even when screw is removed

6 x 35 0313335 6mm 10-16mm 8g 2” 100 7.55

8 x 50 0313450 8 10-20 10 21⁄2 50 10.38

10 x 60 0313560 10 16-30 12 3” 25 20.32

• Ideal for use as a plasterboard fixing as well as lightweight and perforated blocks• For use with woodscrews


GENERAL FIXINGS

Cavity Fixings - 2 APRIL 2010

SPIT DRIVA PLUS • Heavy duty plasterboard fixing which is installed in the same way as the Driva, but has the advantage of a toggle for more substantial loads

FISCHER TYPE PD

QWIKMASTER • Expansion plug for plasterboard of any thickness. Made from tough glass filled nylon. For use with 6-10g woodscrews. Use Pozi Screwdrivers to punch hole in board first then drive Qwikmaster home

METAL DRIVA • Self drilling plasterboard fixing. Installed with a No.2 pozidriver • Comes complete with a 35mm Pan Head Screw

• High load capacity cavity fixing which is fast and easy to install in plasterboard and other board materials• Extra short expansion zone means PD can be installed with only the smallest cavity behind the board• Accommodates double board thicknesses

Suitable for chipboard screws only.

PD 8 0321008 8mm 6mm+ 4.0mm 40mm 100

PD 10 0321010 10mm 7mm+ 5.0mm 40mm 100

PD 12 0321012 12mm 9mm+ 6.0mm 40mm 100

TP12 0330012 - 10-16mm 8g 35mm 100

TP12 PLUS 0330110 - 10-13mm 8g 45mm 100

QM 28 0332028 - 10mm+ 6-10g 11⁄1⁄1 4⁄4⁄ 100

PRODUCT MF DRILL BOARD SCREW MIN. BOX PRICE CODE CODE SIZE THICKNESS DIA. LGTH QTY. PER 100x PRODUCT MF DRILL BOARD SCREW MIN. BOX PRICEx PRODUCT MF DRILL BOARD SCREW MIN. BOX PRICE CODE CODE SIZE THICKNESS DIA. x CODE CODE SIZE THICKNESS DIA.

FISCHER TYPE UX-R

13mm 0317013 8mm 13-16mm 8-12g 2” 1008mm 13-16mm 8-12g 2” 1008mm 13-16mm 8-12g 2” 1008mm 13-16mm 8-12g 2” 100 15.30

POLYTOGGLE • Medium duty plasterboard fixing. stays in place even when screw is removed

6 x 35 0313335 6mm 10-16mm 8g 2” 100 7.55

8 x 50 0313450 8 10-20 10 21⁄1⁄1 2⁄2⁄ 50

10 x 60 0313560 10 16-30 12 3” 25

• Ideal for use as a plasterboard fixing as well as lightweight and perforated blocks• For use with woodscrews

TEL: (0115) 922 1585

click on an image to view other sections of the

Midland Fixings cataloguein pdf format

Sections from the Midland Fixings Catalogue

http://www.midfix.co.uk/downloads/SECTION_01.pdf

http://www.midfix.co.uk/downloads/SECTION_04.pdf

section 01 general fixings

Documents