sebu8124-03 b oruga.pdf
TRANSCRIPT
8/10/2019 SEBU8124-03 B Oruga.pdf
http://slidepdf.com/reader/full/sebu8124-03-b-orugapdf 1/4
®© 2010 CaterpillarAll Rights Reserved
BEFORE OPERATIONOperation and MaintenanceManual Excerpt
8/10/2019 SEBU8124-03 B Oruga.pdf
http://slidepdf.com/reader/full/sebu8124-03-b-orugapdf 2/4
SEBU8124-03
March 2008
Operation andMaintenance
ManualD6N Track-Type Tractor
DJA1-Up (Machine)JAH1-Up (Machine)ERL1-Up (Machine)JAL1-Up (Machine)
DJY1-Up (Machine)
SAFETY.CAT.COM
8/10/2019 SEBU8124-03 B Oruga.pdf
http://slidepdf.com/reader/full/sebu8124-03-b-orugapdf 3/4
34 SEBU8124-03Operation SectionBefore Operation
Operation Section
Before Operation
i02189821
Mounting and Dismounting
SMCS Code: 7000
g00037860Illustration 27
Typical example
Mount the machine and dismount the machine onlyat locations that have steps and/or handholds. Beforeyou mount the machine, clean the steps and thehandholds. Inspect the steps and handholds. Make
all necessary repairs.
Face the machine whenever you get on the machineand whenever you get off the machine.
Maintain a three-point contact with the steps and withthe handholds.
Note: Three-point contact can be two feet and onehand. Three-point contact can also be one foot andtwo hands.
Do not mount a moving machine. Do not dismount amoving machine. Never jump off the machine. Do
not carry tools or supplies when you try to mount themachine or when you try to dismount the machine.Use a hand line to pull equipment onto the platform.Do not use any controls as handholds when youenter the operator compartment or when you exit theoperator compartment.
Alternate Exit
Machines that are equipped with cabs have alternateexits. For additional information, see Operation andMaintenance Manual, “Alternate Exit”.
i02014874
Daily Inspection
SMCS Code: 1000; 7000
For a maximum service life of the machine, completea thorough daily inspection before you mount themachine and before you start the engine.
Inspect the area around the machine and under themachine. Look for loose bolts, trash buildup, oil,coolant leakage, broken parts, or worn parts.
Note: Watch closely for leaks. If you observe a leak,find the source of the leak and correct the leak. If yoususpect a leak or you observe a leak, check the fluidlevels more frequently.
Inspect the condition of the equipment and of the
hydraulic components.
Check all of the oil levels, all of the coolant levels,and all of the fuel levels.
Remove any trash buildup and debris. Make allnecessary repairs before you operate the machine.
Make sure that all covers and guards are securelyattached.
Adjust the mirrors for the correct rear view of themachine.
Grease all of the fittings that need to be serviced ona daily basis.
Daily, perform the procedures that are applicable toyour machine:
• Operation and Maintenance Manual, “Backup Alarm - Test”
• Operation and Maintenance Manual, “Brakes,Indicator and Gauges - Test”
• Operation and Maintenance Manual, “Cab Filter (Fresh Air) - Clean/Inspect/Replace”
• Operation and Maintenance Manual, “CoolingSystem Level - Check”
• Operation and Maintenance Manual, “Engine OilLevel - Check”
• Operation and Maintenance Manual, “Fuel SystemPrimary Filter/Water Separator - Drain”
• Operation and Maintenance Manual, “Fuel TankWater and Sediment - Drain”
8/10/2019 SEBU8124-03 B Oruga.pdf
http://slidepdf.com/reader/full/sebu8124-03-b-orugapdf 4/4
SEBU8124-03 35Operation SectionBefore Operation
• Operation and Maintenance Manual, “HydraulicSystem Oil Level - Check”
• Operation and Maintenance Manual, “Seat Belt -Inspect”
• Operation and Maintenance Manual, “TransmissionOil Level - Check”