scope of accreditation - s-geexpertdirectory.s-ge.com › data › ...scc_accreditation.pdf · the...

SCOPE OF ACCREDITATION

NEMKO CANADA INC.303 River Road

Ottawa, ONK1V 1H2

Accredited Laboratory No. 75(Conforms with requirements of CAN-P-4E (ISO/IEC 17025:2005))

CONTACT: Mr. Stuart Beck TEL: +1 613 737 9680 FAX: +1 613 737 9691 EMAIL: [email protected] URL: www.nemko.com

CLIENTS SERVED: All interested parties, some tests are available on-site.

FIELDS OF TESTING: Electrical/Electronic, Optics & Optical Radiation

ISSUED ON: 2013-09-19

VALID TO: 2015-08-13

The following is a Scope of Accreditation for which this testing laboratory has been accredited to ISO/IEC17025:2005. Note that the parent organization is also accredited as a certification body. The parentorganization�s Scope of Accreditation for certification activities may be broader than the listing of standardsand test methods that appear below. Refer to the parent organization's Scope of Accreditation granted by theSCC for certification activities found at:http://www.scc.ca/en/accreditation/product-process-and-service-certification/directory-of-accredited-clientsWhere standards, such as product standards, are listed below, the laboratory is considered accredited only forthe testing elements in those standards.

Additional Locations*:1500 Peter Robinson Side Road, West Carleton, Ontario, K0A 1L0 (Almonte Facility)

292 Labrosse Avenue, Pointe-Claire, Quebec, H9R 5L8 (Nemko Montreal)

ELECTRICAL PRODUCTS AND ELECTRONIC PRODUCTSThe approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do of 22

http://www.scc.ca/en/accreditation/product-process-and-service-certification/directory-of-accredited-clients

(Energy Efficiency 1, 2)

20 CCR 1604 (v) Televisions and consumer equipment and Video Equipment20 CCR 1604 (w) Battery Charger SystemsCAN/CSA-C62301-07 IEC62301

Household electrical appliances - Measurement of standbypower

CSA-C380-08 Test procedure for the measurement of energy consumption ofset-top boxes (STBs)

CSA-C381.1-08 Test method for calculating the energy efficiency ofsingle-voltage external ac-dc and ac-ac power supplies

ENERGY STAR ProgramRequirements for Set-top Boxes

ENERGY STAR Test Method for Set-top Boxes (TestingProducts for ENERGY STAR)ENERGY STAR Program for Set-top Boxes.

ENERGY STAR ProgramRequirements for Televisions

ENERGY STAR Test Method for Televisions, ENERGYSTAR Program Requirements for Televisions, Rev. Aug-2010-IEC 62087, Ed 2.0: Methods of Measurement for the PowerConsumption of Audio, Video and Related Equipment-CEA-2037: Determination of Television Average PowerConsumption (December 2009) -IEC 62301, Ed 1.0:Household Electrical Appliances � Measurement of StandbyPower. -CEA: Procedure for DAM TestingNOPR Federal register Vol 77, No.12 Jan 19, 2012 (10 CFRPart 430)

ENERGY STAR ProgramRequirements ProductSpecification for Audio/Video

ENERGY STAR Test Method for Audio/Video, ENERGYSTAR Program Requirements Product Specification forAudio/Video

ENERGY STAR ProgramRequirements ProductSpecification for BatteryCharging Systems

ENERGY STAR Test Method, ENERGY STAR ProgramRequirements for Battery Charging Systems, Rev. Aug-2010 -IEC Standard 61951-1: Secondary cells and batteriescontaining alkaline or other non-acid electrolytes - Portablesealed rechargeable single cells - Part 1: Nickel-cadmium. Ed.2.1. January 2006 - IEC Standard 61951-2: Secondary cellsand batteries containing alkaline or other non-acid electrolytes- Portable sealed rechargeable single cells - Part 2:Nickel-metal hydride. Ed. 2.0. April 2003 - IEC Standard61960: Secondary cells and batteries containing alkaline orother non-acid electrolytes - Secondary lithium cells andbatteries for portable applications. Ed. 1.0. December 2003

ENERGY STAR ProgramRequirements ProductSpecification for ComputerServers

ENERGY STAR Test Method for Computer Servers,ENERGY STAR Test Procedure for Determining the PowerUse of Computer Servers at Idle and Full Load (Appendix Aof specification) EPRI Generalized Test Protocol forCalculating the Energy Efficiency of Internal Ac-Dc andDc-Dc Power Supplies. Available atwww.efficientpowersupplies.org. IEC 62301: HouseholdElectrical Appliances - Measurement of Standby Power

ENERGY STAR ProgramRequirements ProductSpecification for Computers

ENERGY STAR Computer Test Method, ENERGY STARProgram Requirements Product Specification forComputers, with methods EPRI Generalized Test Protocol for

Standards Council of Canada Accredited Laboratory No. 75

The approved and most recent version of this document can be viewed on the SCC website at http://palcan.scc.ca/SpecsSearch/GLSearchForm.do of 22

Calculating the Energy Efficiency of Internal Ac-Dc andDc-Dc Power Supplies. (for products that have internal,multi-output, or single output with integral cooling powersupplies; available at: www.efficientpowersupplies.org) IEC62301: Household Electrical Appliances - Measurement ofStandby Power

ENERGY STAR ProgramRequirements ProductSpecification for Displays

ENERGY STAR Test Method for Displays, ENERGY STARProgram Requirements Product Specification for Displays,page 11 -IEC 62087, : Methods of Measurement for thePower Consumption of Audio, Video and Related Equipment-IEC 62301: Household Electrical Appliances-Measurementof Standby Power

ENERGY STAR ProgramRequirements ProductSpecification for ImagingEquipment

ENERGY STAR Imaging Equipment Test Method, ENERGYSTAR Program Requirements, Product Specification forImaging Equipment, page 20 - IEC 62301 Ed 1.0: HouseholdElectrical Appliances - Measurement of Standby Power -EPRI Generalized Test Protocol for Calculating the EnergyEfficiency of Internal Ac-Dc and Dc-Dc Power Supplies.Available at www.efficientpowersupplies.org Test Method forCalculating the Energy Efficiency of Single Voltage ExternalAC-DC and AC-AC Power Supplies

ENERGY STAR ProgramRequirements ProductSpecification for Telephony

ENERGY STAR Test Method for Telephony, ENERGYSTAR Program Requirements for Telephony.

ENERGY STAR Test Methodfor Calculating the EnergyEfficiency of Single VoltageExternal AC-DC and AC-ACPower SuppliesENERGY STAR Testmethodology for Determining theEnergy Performance of BatteryCharging SystemsENERGY STAR ProgramRequirements for ComputerServersEPRI Generalized Test Protocolfor Calculating the EnergyEfficiency of Internal AC-DCand DC-DC Power SuppliesIEC 62087:2008IEC 62087:2011

Methods of Measurement for the Power Consumption ofAudio, Video, and Related Equipment

Communications Equipment and Systems:

(Electromagnetic Compatibility and Interference (EMC and EMI)*1, 2)

AS/NZS CISPR 11CISPR 13EN55013

Sound and television broadcast receivers and associatedequipment - Radio Disturbance characteristics - Limits andmethods of measurement



KN 13CISPR 11EN55011KN 11

Industrial, scientific and medical (ISM) radio-frequencyequipment - Radio disturbance characteristics - Limits andmethods of measurement

CISPR 14-1EN55014-1KN 14-1

Electromagnetic compatibility - requirements for householdappliances, electric tools and similar apparatus - Part 1:Emission

CISPR 14-2EN55014-2KN 14-2

Electromagnetic compatibility - requirements for householdappliances, electric tools and similar apparatus - Part 2:Immunity-Product family standard

CISPR 15EN 55015KN 15

Limits and methods of measurement of radio disturbancecharacteristics of electrical lighting and similar equipment


Sound and television broadcast receivers and associatedequipment-Immunity characteristics-Limits and methods ofmeasurement

CISPR 22EN 55022KN 22AS/NZ CISPR 22

Limits and methods of measurement of radio disturbancecharacteristics of information technology equipment


Information technology equipment - Immunity characteristics- Limits and methods of measurement

CNS 13438 Taiwan EMC for information technology equipmentEN 300 386 Electromagnetic compatibility and Radio spectrum Matters

(ERM);Telecommunication networkequipment;ElectroMagnetic Compatibility (EMC)requirements

EN 300 386-2 Electromagnetic compatibility and Radio spectrum Matters(ERM); Telecommunication network equipment;Electromagnetic compatibility (EMC) requirements; Part 2:Product family standard

EN 301 489-01 to EN 301489-34KN 301 489

Electromagnetic compatibility and Radio spectrum Matters(ERM); Electromagnetic compatibility (EMC) standard forradio equipment and services

EN 50121-3-2 Railway applications. Electromagnetic compatibility. Rollingstock. Apparatus

EN 50130-4 Alarm Systems - Part 4: Electromagnetic compatibility -Product family standard: Immunity requirements forcomponents for fire, intruder and social alarm systems

EN 50136-2-3 Alarm systems - Alarm transmission systems and equipmentPart 2-3: Requirements for equipment used in systems withdigital communicators using the public switched telephonenetwork

Only for: Electrostatic discharge test in clause 6.3Environmental testing

EN 50155 Railway applications. Electronic equipment used on rollingstock



EN 60601-1-2IEC 60601-1-2

Medical electrical equipment - Part 1-2: General requirementsfor safety - Collateral standard : Electromagneticcompatibility - Requirements and tests

EN 61000-3-2IEC 61000-3-2AS/NZS 61000.3.2

Electromagnetic compatibility (EMC) - Part 3-2: Limits -Limits for harmonic current emissions (equipment inputcurrent up to and including 16A per phase)

EN 61000-3-3IEC 61000-3-3AS/NZS 61000.3.3

Electromagnetic compatibility (EMC) - Part 3-3: Limits -Limitation of voltage changes, voltage fluctuations and flickerin public low-voltage supply systems, for equipment withrated current 'less than or equal to' 16A per phase and notsubject to conditional connection

EN 61000-4-11IEC 61000-4-11KN 61000-4-11

Electromagnetic compatibility (EMC) - Part 4-11: Testing andmeasurement techniques - Voltage dips, short interruptionsand voltage variations immunity test

EN 61000-4-2IEC 61000-4-2KN 61000-4-2

Electromagnetic compatibility (EMC) - Part 4-2: Testing andmeasurement techniques - Electrostatic discharge immunitytest

EN 61000-4-3IEC 61000-4-3KN 61000-4-3

Electromagnetic compatibility (EMC) - Part 4-3: Testing andmeasurement techniques - Radiated, radio-frequency,electromagnetic field immunity

EN 61000-4-4IEC 61000-4-4KN 61000-4-4

Electromagnetic compatibility (EMC) - Part 4-4: Testing andmeasurement techniques - Electrical fast transient/burstimmunity test

EN 61000-4-5IEC 61000-4-5KN 61000-4-5

Electromagnetic compatibility (EMC) - Part 4-5: Testing andmeasurement techniques - Surge immunity test

EN 61000-4-6IEC 61000-4-6KN 61000-4-6

Electromagnetic compatibility (EMC) - Part 4-6: Testing andmeasurement techniques - Immunity to conducteddisturbances, induced by radio-frequency fields

EN 61000-4-8IEC 61000-4-8KN 61000-4-8

Electromagnetic compatibility (EMC) - Part 4-8: Testing andmeasurement techniques - Power frequency magnetic fieldimmunity test

EN 61000-6-1IEC 61000-6-1

Electromagnetic compatibility (EMC) - Part 6-1: Genericstandards - Immunity for residential, commercial andlight-industrial environments

EN 61000-6-2IEC 61000-6-2

Electromagnetic compatibility (EMC) - Part 6-2: Genericstandards - Immunity for industrial environments

EN 61000-6-3IEC 61000-6-3

Electromagnetic compatibility (EMC) - Part 6-3: Genericstandards - Emission standard for residential, commercial andlight-industrial environments

EN 61000-6-4IEC 61000-6-4

Electromagnetic compatibility (EMC)-Part 6-4: Genericstandards-Emission standard for industrial environments

EN 61326-1IEC 61326-1

Electrical equipment for measurement, control and laboratoryuse - EMC requirements - Part 1: General requirements

EN 61326-2-1IEC 61326-2-1

Electrical equipment for measurement, control and laboratoryuse - EMC requirements - Part 2-1: Particular requirements -Test configurations, operational conditions and performancecriteria for sensitive test and measurement equipment forEMC unprotected applications



EN 61326-2-2IEC 61326-2-2

Electrical equipment for measurement, control and laboratoryuse - EMC requirements - Part 2-2: Particular requirements -Test configurations, operational conditions and performancecriteria for portable test, measuring and monitoring equipmentused in low-voltage distribution systems

EN 61326-2-3IEC 61326-2-3

Electrical equipment for measurement, control and laboratoryuse - EMC requirements - Part 2-3: Particular requirements -Test configuration, operational conditions and performancecriteria for transducers with integrated or remote signalconditioning

EN 61326-2-4IEC 61326-2-4

Electrical equipment for measurement, control and laboratoryuse - EMC requirements - Part 2-4: Particular requirements -Test configurations, operational conditions and performancecriteria for insulation monitoring devices according to IEC61557-8 and for equipment for insulation fault locationaccording to IEC 61557-9

EN 61326-2-5IEC 61326-2-5

Electrical equipment for measurement, control and laboratoryuse - EMC requirements - Part 2-5: Particular requirements -Test configurations, operational conditions and performancecriteria for field devices with interfaces according to IEC61784-1, CP 3/2

EN 61326-2-6IEC 61326-2-6

Electrical equipment for measurement, control and laboratoryuse-EMC requirements Part 2-6: Particular requirements-In vitro diagnostic (IVD) medical equipment

EN 61326-3-2IEC 61326-3-2

Electrical equipment for measurement, control and laboratoryuse - EMC requirements - Part 3-2: Immunity requirementsfor safety-related systems and for equipment intended toperform safety-related functions (functional safety) -Industrial applications with specified electromagneticenvironment

EN50131-1 Alarm systems - Intrusion and hold-up systems - Part 1:System requirementsOnly for: Clause 12.1 EMC requirements

EN50131-2-2 Alarm systems - Intrusion and hold-up systems Part 2-2:Intrusion detectors - Passive infrared detectorsOnly for: EMC according to EN 50130-4 in clause 4.7.2Immunity to environmental conditions

EN50131-2-4 Alarm systems - Intrusion and hold-up systems Part 2-4:Requirements for combined passive infrared and microwavedetectors

Only for: EMC according to EN 50130-4 in clause 4.7.2Immunity to environmental conditions

EN50131-2-6 Alarm systems Intrusion and hold-up systems Part 2-6:Opening contacts (magnetic)Only for: EMC according to EN 50130-4 and EN 61000-6-3 in clause 4.7.2 Immunity to environmental conditions

EN50131-3 Alarm systems Intrusion and hold-up systems Part 3: Controland indicating equipmentOnly for: EMC tests per EN 50130-4 in clause 11.14Environmental and EMC tests



EN50131-4 Alarm systems Intrusion and hold-up systems Part 4: WarningdevicesOnly for: EMC tests per EN 50130-4 in clause 11.14Environmental and EMC tests

EN50131-6 Alarm systems - Intrusion and hold-up systems Part 6: PowersuppliesOnly for: Clause 4.14 EMC

EN50136-2-1 Alarm systems Alarm transmission systems and equipmentPart 2-1: General requirements for alarm transmissionequipmentOnly for: Clause 7 Electromagnetic Compatibility testing andrequirements

ETS 300 086 LMR-Land Mobile RadioETS 300 113 Radio Equipment and Systems (RES); Land mobile serviceETS 300 339 General EMC for Radio DevicesETS 300 385 EMC for Radio Relay Systems @ 2 MbpsETS 300 683 EMC 9 KHz - 25 GHzFCC 12/CIS22: (IEC/CISPR22:1993)

Limits and methods of measurement of radio disturbancecharacteristics of information technology equipment

FCC 47 CFR 15 Radio Frequency DevicesFCC Part 15 12/F01 Digital DevicesFCC Part 15 12/F01a Conducted Emissions, Power Lines, 450 KHz to 30 MHzFCC Part 15 12/F01b Radiated EmissionsFCC Part 15 12/T01 Terminal Equipment Network Protection Standards,IC ICES 001 Interference Causing Equipment Standards, Industrial, etc.ICES-003 Spectrum Management, Interference-Causing Equipment

Standard Digital ApparatusIDA TS EMC EMC requirements for Telecommunication EquipmentMIC Notice Republic of Korea - Technical Regulation Criteria for EMIMIC Notice Republic of Korea - Technical Regulation Criteria for EMSRRL Notice Republic of Korea - Technical Regulation Test Method for

EMIRRL Notice Republic of Korea - Technical Regulation Test Method for

EMSRRL Notice Republic of Korea - Technical Requirements for

Electromagnetic InterferenceRRL Notice Republic of Korea - Technical Requirements for

Electromagnetic SusceptibilityRRL Notice Republic of Korea - Test Methods for Electromagnetic

InterferenceRRL Notice Republic of Korea - Test Methods for Electromagnetic

SusceptibilityTBR 26 Satellite Earth Stations and Systems (SES); Low data rate

Land Mobile satellite Earth Stations (LMES) operating in the1,5/1,6 GHz frequency bands

VCCI Agreement of Voluntary Control Council for Interference byinformation technology equipment



(Telecommunications Terminal Equipment *1)

ADSL01 Asymmetric Digital Subscriber Line Terminal Equipment andPOTS Splitter Technical Specifications

AS/ACIF S003 Customer Switching, multiplexing and ancillary equipmentfor connection to the telecommunications network

AS/ACIF S004 Voice frequency performance requirements for customerequipment

AS/ACIF S006 Requirements for customer equipment, operating in the voiceband, for connection to the Non-switched telephone network.

AS/ACIF S016 Requirements for customer equipment for connection to tohierarchical digital interfaces

AS/ACIF S031 Requirements for ISDN Basic Access InterfaceAS/ACIF S038 Requirements for ISDN Primary Rate Access InterfaceAS/ACIF S040 Requirements for Customer Equipment for use with the

Standard Telephone Service-Features for special needsAS/ACIF S043 Parts 1,2 Requirements for Customer Equipment for Connection to a

Metallic Loop Interface of a Telecommunications Network -Part 1: General, Part 2: Broadband and Part 3: DC, LowFrequency AC and Voiceband.

AS/CA S002 Analogue Interworking and non-interference requirements forCustomer Equipment for connection to the Public SwitchTelephone Network

AS/CA S003.1 Requirements for Customer Access Equipment for connectionto a Telecommunications Network, Part 1 : General

AS/CA S003.2 Requirements for Customer Access Equipment for connectionto a Telecommunications Network, Part 2 : Analogue andTDM based Technologies

AS/CA S003.3 Requirements for Customer Access Equipment for connectionto a Telecommunications Network, Part 3 : Packet and Cellbased Technologies

ETSI ES 203 021-1 Access and Terminals (AT);Harmonized basic attachmentrequirements for Terminals for connection to analogueinterfaces of the Telephone Networks;Update of the technicalcontents of TBR 021, EN 301 437, TBR 015, TBR 017;Part 1:General aspects

ETSI ES 203 021-2 Access and Terminals (AT);Harmonized basic attachmentrequirements for Terminals for connection to analogueinterfaces of the Telephone Networks;Update of the technicalcontents of TBR 021, EN 301 437, TBR 015, TBR 017;Part 2:Basic transmission and protection of the network from harm

ETSI ES 203 021-3 Access and Terminals (AT);Harmonized basic attachmentrequirements for Terminals for connection to analogueinterfaces of the Telephone Networks;Update of the technicalcontents of TBR 021, EN 301 437, TBR 015, TBR 017;Part 3:Basic Interworking with the Public Telephone Networks

FCC Part 68 FCC Rules for registration of Telephone Equipment(Analogue devices)

HKTA 2011



Network Connection Specification for Connection ofCustomer Premises Equipment (CPE) to Direct ExchangeLines (DEL) of the Public Switched Telephone Network(PSTN) of Hong Kong.

HKTA 2015 Network Connection Specification for Connection ofCustomer Premises Equipment (CPE) to the PublicTelecommunication Network (PTN) in Hong Kong usingISDN Primary Rate Access (PRA) at 1544 Kbits/s

HKTA 2017 NETWORK CONNECTION SPECIFICATION FORCONNECTION OF CUSTOMER PREMISES EQUIPMENT(CPE) TO THE PUBLIC TELECOMMUNICATIONSNETWORK (PTN) IN HONG KONG OVER DIGITALTRUNK AT 1544KBIT/S USING DTMF SIGNALLING

HKTA 2028 Network Connection Specification for Connection toCustomer Premises Equipment (CPE) to the PublicTelecommunications Network (PTN) in Hong Kong usingDigital Leased Circuits at Data Rate of 1544 Kbits/s

HKTA 2029 Network Connection Specification for Connection ofCustomer Premises equipment (CPE) to the Public TelephoneNetwork (PTN) in Hong Kong using Digital Leased Circuitsat Data Rate of 2048 Kbits/s

IC CS 03 Part VI Requirements and test methods for ISDN terminal EquipmentIC CS-03 Part I Harmonised requirements for Terminal Equipment, Terminal

Systems, and Certified protection circuitryIC CS-03 Part II Requirements for TE Interfaces for connection to 1.544Mbps

(DS-1) Digital facilitiesIC CS-03 Part V Requirements and Test methods for Magnetic Output from

Handset Telephones for Hearing Aid CouplingIC CS-03 Part VII Requirements for Limited Distance Modems and Digital

Subrate Terminal EquipmentIC CS-03 Part VIII Requirements and Test methods for Digital Subscriber Line

(xDSL) Terminal EquipmentID0002 DS1 Type Approval Requirements (Taiwan)IDA TS DLCN 1(formerly IDA TS DLCAN1)

Digital Interfaces based on hierarchical bit rates of 2048kbit/s,34 368 kbit/s and 139 264 kbit/s

IDA TS ISDN-BA Terminal Equipment for connection to the Integrated ServicesDigital Network (ISDN) using Basic Access

IDA TS ISDN-PRA Terminal Equipment for connection to the Integrated ServicesDigital Network (ISDN) using Primary Rate Access

IDA TS PSTN Technical Specifications for Terminal Equipment forConnection to Public Switched Telephone Network

IS6100 Technical Specifications for Terminal Equipment forConnection to Public Switched Telephone Network (Taiwan)

MIC Notice Republic of Korea - Technical Requirement forTelecommunications Terminal Equipment

PSTN01 Technical Specifications for Terminal Equipment forConnection to Public Switched Telephone Network. (Taiwan)

PTC 200 PTC 200 Requirements for Connection of CustomerEquipment to Analogue Lines



PTC 220 PTC 220: Requirements for Private Voice Networksconnected to PSTN/ISDN

Republic of Korea Regulation on Technical Criteria of TelecommunicationsFacilities.

RRL Notice Republic of Korea - Conformity Assessment Procedure forType Approval of Telecommunications Terminal Equipment

TBR 12: 1993 (WITH A1: 1996) Business Telecommunications (BT); Open Network Provision(ONP) technical requirements; 2 048 kbit/s digitalunstructured leased line (D2048U) Attachment requirementsfor terminal equipment interface

TBR 13: 1996 (CTR 13) Business TeleCommunications (BTC); 2 048 kbit/s digitalstructured leased lines (D2048S); Attachment requirementsfor terminal equipment interface

TBR 15: 1997 (CTR 15) Business TeleCommunications (BTC); Ordinary and Specialquality voice bandwidth 2-wire analogue leased lines (A20and A2S); Attachment requirements for terminal equipmentinterface

TBR 17: 1997 (CTR 17) Business TeleCommunications (BTC); Ordinary and Specialquality voice bandwidth 4-wire analogue leased lines (A40and A4S); Attachment requirements for terminal equipmentinterface

TBR 2: 1997 (CTR 2) Attachment requirements for data terminal equipment (DTE)to connect to packet switched Public Data Networks(PSPDNs) for CCITT Recommendation X.25 interfaces atdata signaling rates up to 1 920 kbit/s utilizing interfacesderived from CCITT Recommendations X.21 and X.21 bis

TBR 21: 1998 (CTR 21) Terminal Equipment (TE); Attachment requirements forpan-European approval for connection to the analogue PublicSwitch Telephone Networks (PSTNs) of TE (excluding TEsupporting the voice telephony service) in which networkaddressing, if provided, is by means of Dual Tone MultiFrequency (DTMF) signaling

TBR 24: 1997 (CTR 24) Business Telecommunications (BTC); 34 Mbit/s digitalunstructured and structured leased lines (D34U and D34S);Attachment requirements for terminal equipment interface

TBR 3: 1995 (WITH A1: 1997) Integrated Services Digital Network (ISDN) attachmentrequirements for terminal equipment to connect to an ISDNusing ISDN basic access

TBR 4: 1995 (WITH A1: 1997) Integrated Services Digital Network (ISDN); Attachmentrequirements for terminal equipment to connect to an ISDNusing ISDN primary rate access

TBR1: 1995 (CTR 1) Attachment requirements for terminal equipment to beconnected to circuit switched data networks and leasedcircuits using a CCITT Recommendation X.21 interface, or atan interface physically, functionally and electricallycompatible, with CCITT Recommendation X.21 but operatingat any data signaling rate up to, and including 1 984 kbit/s

TE-001 Standard for Telecommunication Line Terminal Equipment(TLTE) for connection to the Public Switched TelephoneNetwork (PSTN)



TIA-968-A includingAmendments

Technical Requirements for Connection of TerminalEquipment to the Telephone Network

TIA-968B Technical Requirements for Connection of TerminalEquipment to the Telephone Network

TNA 117 TNA 117:1992 Telecom 2048 Kbit/s Standard NetworkInterface

Radio Telecommunication*1, 2

ANSI C63.10 American National Standard for Testing Unlicensed WirelessDevices

ANSI C63.17 American National Standard for methods of measurement ofthe Electromagnetic and Operational Compatibility ofUnlicensed Personal Communications Services (UPCS)Devices

ANSI C63.4 American National Standard for methods of measurement ofradio-noise emissions for low voltage electrical and electronicequipment in the range of 9kHz to 40GHz

ANSI/TIA-603-C Land Mobile FM or PM Communications Equipment. Measurement and performance standards

AS/NZS 4268 Radio equipment and systems - Short range devices - Limitsand methods of measurement

AS/NZS 4771 Technical characteristics and test conditions for datatransmission equipment operating in the 900 MHz, 2.4 GHzand 5.8 GHz bands and using spread spectrum modulationtechniques

ETS 300 279 LMR- Land Mobile Radio, EMCETS 300 487 Satellite earth stations and systems (SES); Receive-only

mobile earth stations (ROMES) operating in the 1,5 GHz bandproviding data communications; Radio frequency (RF)specifications

ETSI EN 300 113-1 Electromagnetic compatibility and Radio spectrum Matters(ERM); Land mobile service; Radio equipment intended forthe transmission of data (and/or speech) using constant ornon-constant envelope modulation and having an antennaconnector; Part 1: Technical characteristics and methods ofmeasurement

ETSI EN 300 113-2 Electromagnetic compatibility and Radio spectrum Matters(ERM); Land mobile service; Radio equipment intended forthe transmission of data (and/or speech) using constant ornon-constant envelope modulation and having an antennaconnector; Part 2: Harmonized EN covering essentialrequirements under article 3.2 of the R&TTE Directive

ETSI EN 300 135-1 Electromagnetic compatibility and Radio spectrum Matters(ERM); Angle-modulated Citizens Band radio equipment(CEPT PR 27 Radio Equipment); Part 1: Technicalcharacteristics and methods of measurement

ETSI EN 300 135-2



Electromagnetic compatibility and Radio spectrum Matters(ERM); Angle-modulated citizens Band radio equipment(CEPT PR 27 Radio Equipment); Part 2: Harmonized ENcovering essential requirements under article 3.2 of R&TTEDirective

ETSI EN 300 219-1 Electromagnetic compatibility and Radio spectrum Matters(ERM); Land Mobile Service; Radio equipment transmittingsignals to initiate a specific response in the receiver; Part 1:Technical characteristics and methods of measurement

ETSI EN 300 219-2 Electromagnetic compatibility and Radio spectrum Matters(ERM); Land Mobile Service; Radio equipment transmittingsignals to initiate a specific response in the receiver; Part 2:Harmonized EN covering essential requirements under article3.2 of the R&TTE Directive

ETSI EN 300 220-1 Electromagnetic compatibility and Radio spectrum Matters(ERM);Short Range Devices (SRD); Radio Equipment to beused in the 25 MHz to 1 000 MHz frequency range withpower levels ranging up to 500 mW;Part 1: Technicalcharacteristics and test methods

ETSI EN 300 220-2 Electromagnetic compatibility and Radio spectrum Matters(ERM); Short Range Devices (SRD); Radio equipment to beused in the 25 MHz to 1000 MHz frequency range with powerlevels ranging up to 500 mW; Part 2: Harmonized ENcovering essential requirements under article 3.2 of theR&TTE Directive

ETSI EN 300 224-1 Electromagnetic compatibility and Radio spectrum Matters(ERM); On-site paging service; Part 1: Technical andfunctional characteristics, including test methods

ETSI EN 300 224-2 Electromagnetic compatibility and Radio spectrum Matters(ERM); On-site paging service; Part 2: Harmonized EN underarticle 3.2 of the R&TTE Directive

ETSI EN 300 296-1 ElectroMagnetic Compatibility and Radio Spectrum Matters(ERM);Land Mobile Service; Radio equipment using integralantennas intended primarily for analogue speech; Part 1:Technical characteristics and methods of measurement

ETSI EN 300 296-2 Electromagnetic compatibility and Radio spectrum Matters(ERM);Land Mobile Service; Radio equipment using integralantennas intended primarily for analogue speech; Part 2:Harmonized EN covering essential requirements under article3.2 of the R&TTE Directive

ETSI EN 300 328 Electromagnetic compatibility and Radio spectrum Matters(ERM); Wideband transmission systems; Data transmissionequipment operating in the 2,4 GHz ISM band and using wideband modulation techniques; Harmonized EN coveringessential requirements under article 3.2 of the R&TTEDirective

ETSI EN 300 330-1 Electromagnetic compatibility and Radio spectrum Matters(ERM);Short Range Devices (SRD);Radio equipment in thefrequency range 9 kHz to 25 MHz and inductive loop systemsin the frequency range 9 kHz to 30 MHz;Part 1: Technicalcharacteristics and test methods



ETSI EN 300 330-2 Electromagnetic compatibility and Radio spectrum Matters(ERM);Short Range Devices (SRD);Radio equipment in thefrequency range 9 kHz to 25 MHz and inductive loop systemsin the frequency range 9 kHz to 30 MHz;Part 2: HarmonizedEN under article 3.2 of the R&TTE Directive

ETSI EN 300 373-1 Electromagnetic compatibility and Radio spectrum Matters(ERM); Maritime mobile transmitters and receivers for use inthe MF and HF bands; Part 1: Technical characteristics andmethods of measurement

ETSI EN 300 373-2 Electromagnetic compatibility and Radio spectrum Matters(ERM); Maritime mobile transmitters and receivers for use inthe MF and HF bands; Part 2: Harmonized EN coveringessential requirements under article 3.2 of the R&TTEDirective

ETSI EN 300 373-3 Electromagnetic compatibility and Radio spectrum Matters(ERM); Maritime mobile transmitters and receivers for use inthe MF and HF bands; Part 3: Harmonized EN coveringessential requirements under article 3.3(e) of the R&TTEDirective

ETSI EN 300 422-1 Electromagnetic compatibility and Radio spectrum Matters(ERM);Wireless microphones in the 25 MHz to 3 GHzfrequency range;Part 1: Technical characteristics and methodsof measurement

ETSI EN 300 422-2 Electromagnetic compatibility and Radio spectrum Matters(ERM);Wireless microphones in the 25 MHz to 3 GHzfrequency range;Part 2: Harmonized EN covering theessential requirements of article 3.2 of the R&TTE Directive

ETSI EN 300 433-1 Electromagnetic compatibility and Radio spectrum Matters(ERM); Land Mobile Service; Double Side Band (DSB)and/or Single Side Band (SSB) amplitude modulated citizen'sband radio equipment; Part 1: Technical characteristicsand methods of measurement

ETSI EN 300 433-2 Electromagnetic compatibility and Radio spectrum Matters(ERM); Land Mobile Service; Double Side Band (DSB)and/or Single Side Band (SSB) amplitude modulated citizen'sband radio equipment; Part 2: Harmonized EN coveringessential requirementsunder article 3.2 of R&TTE Directive

ETSI EN 300 440-1 Electromagnetic compatibility and Radio spectrum Matters(ERM);Short Range Devices (SRD);Radio equipment to beused in the 1 GHz to 40 GHz frequency range;Part 1:Technical characteristics and test methods

SRD-Short Range Devices 1 GHz - 25 GHzETSI EN 300 440-2 Electromagnetic compatibility and Radio spectrum Matters

(ERM);Short range devices;Radio equipment to be used in the1 GHz to 40 GHz frequency range;Part 2: Harmonized ENunder article 3.2 of the R&TTE Directive

ETSI EN 300 630 Fixed Radio Systems; Point-to-point equipment; Low capacitypoint-to-point digital radio systems operating in the 1,4 GHzfrequency band



ETSI EN 300 633 Fixed Radio Systems; Point-to-point equipment; Low andmedium capacity point-to-point digital radio systemsoperating in the frequency range 2,1 GHz to 2,6 GHz

ETSI EN 301 166-1 Electromagnetic compatibility and Radio spectrum Matters(ERM); Land Mobile Service; Radio equipment for analogueand/or digital communication (speech and/or data) andoperating on narrow band channels and having an antennaconnector; Part 1: Technical characteristics and methods ofmeasurement

ETSI EN 301 166-2 Electromagnetic compatibility and Radio spectrum Matters(ERM); Land Mobile Service; Radio equipment for analogueand/or digital communication (speech and/or data) andoperating on narrow band channels and having an antennaconnector; Part 2: Harmonized EN covering essentialrequirements under article 3.2 of the R&TTE Directive

ETSI EN 301 213 Parts 1, 2 and3

Fixed Radio Systems; Point-to-multipoint equipment;Point-to-multipoint digital radio systems in frequency bandsin the range 24,25 GHz to 29,5 GHz

ETSI EN 301 357-1 Electromagnetic compatibility and Radio spectrum Matters(ERM); Cordless audio devices in the range 25 MHz to 2 000MHz; Part 1: Technical characteristics and test methods

ETSI EN 301 357-2 Electromagnetic compatibility and Radio spectrum Matters(ERM); Cordless audio devices in the range 25 MHz to 2 000MHz; Consumer radio microphones and in-ear monitoringsystems operating in the CEPT harmonized band 863 MHz to865 MHz; Part 2: Harmonised EN under Article 3(2) of theR&TTE Directive

ETSI EN 301 390 Fixed Radio Systems; Point-to-point and Multipoint Systems;Spurious emissions and receiver immunity limits atequipment/antenna port of Digital Fixed Radio Systems

ETSI EN 301 426 Satellite Earth Stations and Systems (SES); Harmonized ENfor Low data rateLand Mobile satellite Earth Stations (LMES) and MaritimeMobile satellite Earth Stations (MMES) not intended fordistress and safety communicationsoperating in the 1,5/1,6 GHz frequency bands coveringessential requirements under article 3.2 of the R&TTEDirective

ETSI EN 301 428 Satellite Earth Stations and Systems (SES); Harmonized ENfor Very Small Aperture Terminal (VSAT);Transmit-only, transmit/receive or receive -only satellite earthstations operating in the 11/12/14 Ghz frequency bandscovering essential requirements under article 3.2 of theR&TTE directive

ETSI EN 301 459 Satellite Earth Stations And Systems (SES); Harmonized ENfor Satellite Interactive Terminals (SIT); and Satellite UserTerminals (SUT) transmitting towards satellites ingeostationary orbitin the 29.5 to 30.0 GHz frequency bandsCovering Essential Requirements Under Article 3.2 ofthe R&TTE Directive



ETSI EN 301 681 Satellite Earth Stations and Systems (SES); Harmonized ENfor Mobile Earth Stations (MESs) of Geostationary mobilesatellite systems, including handheld earth stations, forSatellite Personal Communications Networks (S-PCN) in the1,5/1,6 GHz bands under the Mobile Satellite Service (MSS)covering essential requirements under article 3.2 of theR&TTE Directive

ETSI EN 301 751 Fixed Radio Systems; Point-to-Point equipments andantennas; Generic harmonized standard for Point-to-Pointdigitalfixed radio systems and antennas covering the essentialrequirements under article 3.2 of the 1999/5/EC Directive

ETSI EN 301 893 Broadband Radio Access Networks (BRAN); 5 GHz highperformance RLAN;Harmonized EN covering essential requirements of article 3.2of the R&TTE Directive

ETSI EN 302 208-1 Electromagnetic compatibility and Radio spectrum Matters(ERM); Radio Frequency Identification Equipment operatingin the band 865 MHz to 868 MHz with power levels up to 2W; Part 1: Technical requirements and methods ofmeasurement

ETSI EN 302 208-2 Electromagnetic compatibility and Radio spectrum Matters(ERM); Radio Frequency Identification Equipment operatingin the band 865 MHz to 868 MHz with power levels up to 2W; Part 2: Harmonized EN under article 3.2 of the R&TTEDirective

ETSI EN 302 217-1 Fixed Radio Systems; Characteristics and requirements forpoint-to-point equipment and antennas; Part 1: Overview andsystem-independent common characteristics

ETSI EN 302 217-2-1 Fixed Radio Systems; Characteristics and requirements forpoint-to-point equipment and antennas; Part 2-1:System-dependent requirements for digital systems operatingin frequency bands where frequency co-ordination is applied

ETSI EN 302 217-2-2 Fixed Radio Systems; Characteristics and requirements forpoint-to-point equipment and antennas; Part 2-2: HarmonizedEN covering essential requirements of Article 3.2 of R&TTEDirective for digital systems operating in frequency bandswhere frequency co-ordination is applied

ETSI EN 302 217-3 Fixed Radio Systems; Characteristics and requirements forpoint-to-point equipment and antennas; Part 3: HarmonizedEN covering essential requirements of article 3.2 of R&TTEDirective for equipment operating in frequency bands wheresimplified or no frequency co-ordination procedures areapplied

ETSI EN 302 291-1 Electromagnetic compatibility and Radio spectrum Matters(ERM);Short Range Devices (SRD);Close Range InductiveData Communication equipment operating at 13,56 MHz; Part1: Technical characteristics and test methods

ETSI EN 302 291-2 Electromagnetic compatibility and Radio spectrum Matters(ERM);Short Range Devices (SRD);Close Range InductiveData Communication equipment operating at 13,56 MHz; Part2: Harmonized EN under article 3.2 of the R&TTE Directive



ETSI EN 302 326- Fixed Radio Systems; Multipoint Equipment and Antennas;Part 1: Overview and Requirements for Digital MultipointRadio Systems

ETSI EN 302 326-2 Fixed Radio Systems; Multipoint Equipment and Antennas;Part 2: Harmonized EN covering the essential requirements ofarticle 3.2 of the R&TTE Directivefor Digital Multipoint Radio Equipment

ETSI EN 302 502 Broadband Radio Access Networks (BRAN);5,8 GHz fixedbroadband data transmitting systems; Harmonized ENcovering the essential requirements of article 3.2 of theR&TTE Directive

ETSI EN 300 086 LMR-Land Mobile Radio ServiceETSI EN 300 197 Fixed Radio Systems; Point-to-point equipment; Parameters

for radio systems for the transmission of digital signalsoperating at 32 GHz and 38 GHz

ETSI EN 300 198 Fixed Radio Systems; Point-to-point equipment; Parametersfor radio systems for the transmission of digital signalsoperating at 23 GHz

FCC 47 CFR Part 101 Fixed Microwave servicesFCC 47 CFR Part 11 Emergency Alert SystemsFCC 47 CFR Part 18 Industrial, Scientific and Medical EquipmentFCC 47 CFR Part 21 Domestic Public Fixed RadioFCC 47 CFR Part 22 Public Mobile ServicesFCC 47 CFR Part 24 Personal Communications ServicesFCC 47 CFR Part 25 Satellite CommunicationsFCC 47 CFR Part 26 General Wireless CommunicationsFCC 47 CFR Part 27 Miscellaneous Wireless Communications ServicesFCC 47 CFR Part 73 Radio Broadcast ServicesFCC 47 CFR Part 74 Experimental Radio, Auxiliary and Special BroadcastFCC 47 CFR Part 80 Stations in Maritime ServicesFCC 47 CFR Part 87 Aviation ServicesFCC 47 CFR Part 90 Private Land Mobile Radio ServicesFCC 47 CFR Part 95 Personal Radio ServicesFCC 47 CFR Part 97 Amateur Radio ServiceHKTA 1002 Performance Specification for Angle Modulated Radio

Transmitters and Receivers for Use as Base, Mobile andPortable Equipment in the Land Mobile Radio Service

HKTA 1005 Performance Specification for Angle Modulated VHFMaritime Band Radio Equipment for Voluntary Fitting inSmall Craft

HKTA 1007 Performance Specification for Radio Interference Limits andMethods of Measurements for Industrial, Scientific andMedical (ISM) Radio-Frequency Equipment (ExcludingSurgical Diathermy Apparatus and RF Exciting Arc-WeldingMachines)

HKTA 1008 Performance Specification for Low Power RadioMicrophones, Including Associated Receiving Equipment

HKTA 1010



Performance Specification for Angle Modulated RadioTransmitters and Receivers for use as Base, Mobile andPortable Equipment in the Land Mobile Radio Service andintended primarily for data applications

HKTA 1015 Performance Specification for Cordless Telephone Operatingin the 864.1 - 868.1 MHz Band

HKTA 1016 Performance Specification for Angle Modulated RadioEquipment for Use at Repeater, Base and Mobile Stations in800 MHz Trunked Radio

HKTA 1035 Performance Specification for Low Power DeviceHKTA 1036 Performance Specification for Digital Fixed Link Equipment

Operating in the 38 GHz Frequency BandHKTA 1037 Performance Specification for Digital Fixed Link Equipment

Operating in the 23 GHz Frequency BandHKTA 1039 Performance Specification for Radiocommunications

Apparatus Operating in the 2.4 GHz or 5 GHz Band andEmploying Frequency Hopping or Digital Modulation

HKTA 1041 Performance Specification for RadiocommunicationsApparatus Operating in the 27 MHz Band for Private Use

HKTA 1042 Performance Specification for Radio Equipment Operating inthe 5 GHz Band for Wireless Access

HKTA 1044 Performance Specification for Short-range Portable Radiooperating in the 409 MHz Band

HKTA 1046 Method of Measurement for Radio Transmitter for Use in theLand Mobile Service

HKTA 1049 Performance Specification for Radio Frequency Identification(RFID) Equipment Operating in the 865 - 868 MHz and/or920 - 925 MHz Bands

HKTA 1051 Performance specification for Radio Frequency Identification(RFID) equipment operating in the 433 MHz band

IDA TS LMR Technical Specification for Land Mobile Radio EquipmentIDA TS RPG Technical Specifications for Radio Pagers (Public Paging

Service)IDA TS SRD Technical Specification for Short Range DevicesIDA TS WBA Technical Specification for Wireless Broadband Access

EquipmentIS2019 1.6/2.4GHz Satellite Personal Communications Networks (S

PCN) Mobile Earth Stations (MESs) Technical SpecificationsIS2034-1 Local Multipoint Distribution Service(LMDS) Microwave

Base Station RF Equipment Type Equipment ApprovalTechnical Specifications

IS2045-0 Base Station for Wireless Broadband Access Type ApprovalTechnical Specification

Item 19 of Article 2 (Japan) Radio equipment for low-power data communications systemradio station using a radio wave of 2,400 -2,483.5 MHz

Item 19-3 of Article 2 (Japan) Radio equipment for low-power data communications systemradio station which uses indoors a radio wave of 5,170 MHz,5,190 MHz, 5,210 MHz or 5,230 MHz

Item 8 of Article 2 (Japan) Radio equipment for specified low-power radio station



LP0002 Low Power Radio frequency Devices Technical RegulationsPLMN02 1900MHz Digital Low Tier PHS Radio Terminal Equipment

Technical SpecificationsPLMN03 1900MHz Digital Low Tier PACS Radio Terminal Equipment

Technical SpecificationsPLMN04 Trunked Radio Terminal Equipment Technical SpecificationsPLMN05 Mobile Data Radio Terminal Equipment Technical

SpecificationsPLMN06 Paging Receiver Radio Terminal Equipment Technical

SpecificationsPLMN07 1880-1895MHz Wireless Private Echange and Radio

Terminal Equipment Technical SpecificationsPLMN09 Subscriber Station for Wireless Broadband Access Type

Approval Technical SpecificationRRL Notice Republic of Korea - Technical Requirements for Radio

Equipment of Maritime Mobile Service and Maritime RadioNavigation Service

RRL Notice Republic of Korea - Technical Requirements forMeasurement of Electromagnetic Field Strength

RRL Notice Republic of Korea - Conformity Assessment Procedure forType Approval and Type Registration of Radio Equipment

RRL Notice No. Republic of Korea - Technical Requirements for RadioEquipment of Aeronautical Mobile Service and AeronauticalRadio Service

RRL Notice No. Republic of Korea - Technical Requirements for RadioEquipment of Telecommunications Services

RRL Notice No. Republic of Korea - Technical Requirements for RadioEquipment of Other Services than the Broadcasting, maritime,Aeronautical and Telecommunications Services

RSS 111 Broadband Public Safety Equipment Operating in the Band4940-4990 MHz

RSS 112 Land Mobile and Fixed Equipment Operating in the Band1670-1675 MHz

RSS 117 Land And Coastal Station Transmitter Using A1, A2, A3 A2HEmission Operating In The Cellular Mobile Bands 824-849MHz And 869-894 MHz

RSS 118 Land and Subscriber Stations: Voice, Data and Tonemodulated Angle Modulation RadioTelephone Transmittersand Receivers Operating in the Cellular Mobile Bands824-849MHz and 869-894Mhz

RSS 119 Land Mobile And Fixed Radio Transmitters And Receivers,27.41 to 960.0 MHz

RSS 123 Lower Power Licensed Radiocommunication DevicesRSS 125 Land Mobile And Fixed Radio Transmitters And Receivers

1.705 to 50.0 MHz, Primarily Amplitude ModulatedRSS 127 Air-Ground Equipment Operating in the Bands 849-851 MHz

and 894-896 MHzRSS 129 800 MHz Dual-Mode CDMA Cellular Mobile Radiophones



RSS 131 Zone Enhancers for the Land Mobile ServiceRSS 132 800MHz Cellular Telephones employing new TechnologiesRSS 133 2 GHz Licensed Personal Communications ServicesRSS 134 Narrowband 900 MHz Personal Communications ServicesRSS 135 Digital Scanner ReceiversRSS 136 Land and Mobile Station Radio Telephone Transmitters &

Receivers operating in 26.960-27.410MHz General RadioService Band

RSS 137 Location And Monitoring Service in 902-928 MHz BandRSS 138 Commercial Shipborne Radar in the 2900-3100 MHz,

5470-5650 MHz and 9225-9500 MHz BandsRSS 139 Advanced Wireless Services Equipment Operating in the

Bands 1710-1755 MHz and 2110-2155 MHzRSS 141 Aeronautical Radiocommunication Equipment in the

frequency band 117.975-137MHzRSS 142 Narrowband Multipoint Communication Systems in the

1427-1430MHz and 1493.5-1496.5MHz BandsRSS 170 Satellite Mobile Earth StationsRSS 181 Coast And Ship Station Single Band Radiotelephones,

Transmitters And Receivers operating in the 1605 - 28000kHzBand

RSS 182 Marine Radio Transmitter And Receivers In The Band156-162.5 MHz

RSS 191 Local Multipoint Communications Systems in the 28 GHz;Point-To-Point And Point-To-Multipoint BroadbandCommunication Systems in the 24 & 38 GHz Bands

RSS 192 Fixed Wireless Access Systems In The Band 3400-3700 MHzRSS 193 Multipoint and Point-to-Point Communications

Systems(MCS) in the Fixed Service operating in the2150-2160MHz, 2500-2596MHz and 2686-2690MHz bands

RSS 194 Fixed Wireless Access Equipment Operating in the Band953-960 MHz

RSS 196 Point-to-Multipoint Broadband Equipment Operating in theBands 512-608 MHz and 614-698 MHz for Rural RemoteBroadband Systems (RRBS) (TV Channels 21 to 51)

RSS 197 Wireless Broadband Access Equipment Operating in the Band3650-3700 MHz

RSS 199 Broadband Radio Service (BRS) Equipment Operating in theBand 2500-2690 MHz

RSS 210 Low-Power License - Exempt Radiocommunication DevicesRSS 213 2 GHz License-Exempt Personal Communications Service

(Devices (PCS)RSS 215 Analogue Scanner ReceiversRSS 220 Devices Using Ultra-Wideband (UWB) TechnologyRSS 243 Active Medical Implant Communications System Devices in

the 402MHz to 405MHz BandRSS 287 (formerly RSS 187) Emergency Position Indicating Radio Beacons, Emergency

Locator Transmitters and Personal Locator Beacons



RSS 288 Global Maritime Distress And Safety Systems (GMDSS)RSS 310 Low-Power Licence-Exempt Radiocommunication Devices

(All Frequency bands): Category II equipmentRSS GEN General Requirements and Information for the Certification of

Radiocommunication EquipmentRSS-195 Wireless Communications Service Equipment Operating in

the bands 2305 -2320MHz and 2345 - 2360MHzRTTE01 2.4GHzRadio-frequency Telecommunications Terminal

Equipment Technical SpecificationTBR 41 Satellite Personal Communications Networks

(FCC Methods - Electromagnetic Compatibility & Telecommunications *1, 2)

DA 00-705 - March 2000 andKDB Pub No. 558074 with FCCmethod 47 CFR Part 15, SubpartC

Filing and Measurement Guidelines for Frequency HoppingSpread Spectrum Systems and New Guidance onMeasurements for Digital Transmission Systems in section15.247 (SS-MP)

Intentional RadiatorsDA 02-2138 with FCC method47 CFR Part 15 Subpart E

Unlicensed National Information Infrastructure DevicesMeasurement Procedure (UNII-MP)

FCC/OST MP-5 FCC Methods of Measurements of Radio Noise Emissionsfrom Industrial, Scientific and Medical Equipment

KDB Pub No 200443 Millimeter Wave Test Procedure

(Safety Requirements 1, 2)

CSA C22.2 No. 205 Signal EquipmentExcept for: Across the line capacitors; Evaluation of coatingson printed wiring boards; Swivel Test; Flame test forpolymeric materials; Insulation capacitors and networks

CSA C22.2 No. 60950-1AS/NZS 60950.1IEC 60950-1EN 60950-1UL 60950-1

Safety of Information Technology EquipmentExcept for: Creepage distances (Tracking index as per IEC60112)Partial Discharge Test (IEC 60747-5-5)AC Power Supply cords (IEC 60227)Cathode Ray Tube (CRT)Flammable Liquids measurementEffect of UV Radiation on materials (Table 4A tests)Human exposure to UV Radiation (IEC 60825-9)Hot Flaming Oil Test Mandrel test as per IEC 61558

EN 60215 Safety requirements for radio transmitting equipmentExcept for: Resistance to ingress of water (IEC Publication68-2); Insulation (IEC Publication 112-CTI); Flammability asper IEC Publication 695; Cl.21.2-Implosion

EN 61010-2-010IEC 61010-2-010CAN/CSA 61010-2-010

Safety requirements for electrical equipment formeasurement, control and laboratory use-Part 2-010:Particular requirements for laboratory equipment for the



heating of materialsEN 61010-2-030IEC 61010-2-030CAN/CSA 61010-2-030

Safety requirements for electrical equipment formeasurement, control, and laboratory use-Part 2-030:Particular requirements for testing and measuring circuits

EN 61010-2-101IEC 61010-101CAN/CSA 61010-101

Safety Requirements for Electrical Equipment forMeasurement, Control and Laboratory Use-Part 2-101:Particular Requirements for In Vitro Diagnostic (IVD)Medical Equipment

EN 61010-2-81IEC 61010-2-81CAN/CSA 61010-2-81

Safety Requirements for Electrical Equipment forMeasurement, Control, and Laboratory Use-Part 2-081:Particular Requirements for Automatic and Semi-AutomaticLaboratory Equipment for Analysis and Other Purposes

EN61010-1/CSA C22.2No. 61010.1IEC 61010-1UL 61010-1

Safety Requirements for Electrical Equipment for Measuring,Control and Laboratory Use, Part I - General RequirementsExcept for: Creepage distance (Tracking indexInsulating materials (VICAT A) as per IEC 60112)UV RadiationMicrowave RadiationUltrasonic PressureCathode Ray Tube (CRT)Softening temperature (Vicat ISO 306 Method)Specially protected equipment (IP rated)Leakage and rupture at high pressure

IEC 60825-1EN 60825-1

Safety of Laser Products - Part 1: Equipment classification,requirements and user's guide

IEC 60825-2EN 60825-2

Safety of Laser Products - Part 2: Safety of optical fibrecommunication systems

IEC 60950-21CSA C22.2 No. 60950-21EN 60950-21

Information technology equipment - Safety, Part 21: RemotePower Feeding

Korean Safety RRA Notice 2011-14 (2011.02.28)Taiwan Safety: CNS 14336 Safety of Information Technology Equipment including

Electrical Business EquipmentUL 60065EN 60065CSA C22.2 60065IEC 60065

Standard for Audio, Video and Similar ElectronicApparatus-Safety RequirementsExcept for: Softening temperature test as per ISO 306 ;Vibration Test ; Dielectric Strength test for sheet materials(fig 6); Vibration Test; Remote Controls (Tumbling barrel) ;Creepage distances (proof tracking index) ; Capacitors andRC units ; Thermal cutouts (IEC 60730) ; Fuse linlkslinks andFuseholders (IEC 60127); PTC Thermistors (IEC 60730-1);Switches (IEC 61058-1); Surge Suppressor Resistors; (IEC61051-2); Plugs and sockets (IEC 60083, IEC 60320, IEC60884 and IEC 60906); External Flexible Cords (IEC 60227);Mechanical Strength of picture tubes and protection againsteffects of implosion ; For apparatus with protection againstsplashing water (IEC 60529) ; Insulated winding wires for usewith interleaved insulation

UL 60601-1CSA C22.2 60601-1

Medical Electrical Equipment, Part 1: General Requirementsfor Safety



EN 60601-1IEC 60601-1

Except for: Common-mode and differential-mode voltagetests for defibrillation-proof applied partsEnergy Reduction test for defibrillation-proof applied partsNatural latex rubber tests in an oxygen atmosphereMaterials group classification (Tracking index as per IEC60112)CRTHand transmitted vibration test (ISO 5349-1)Hydraulic Pressure TestX-radiation measurementsSpark Ignition TestSterilization testsPTC Thermistor tests (IEC 60730-1)Lithium battery tests (IEC 60086-4)Prevention of electrostatic charges (ISO 1853, ISO 2878, ISO23529)Insulated winding wire tests (IEC 60851 series)

Notes:

CAN-P-4E (ISO/IEC 17025): General Requirements for the Competence of Testing and CalibrationLaboratories (ISO/IEC 17025-2005)CAN-P-1632: Requirements for The Accreditation of Testing and Calibrations Laboratories Performingon-site Testing and Calibrations* 1 - Marked sections are also performed at the permanent additional locations identified on Page 1. 2 - Marked sections are also performed at sites away from the main location (on-site testing as perCAN-P-1632) identified on Page 1.

Chantal Guay, ing., P. Eng.Vice President, AccreditationServices

Date: 2013-09-19

Number of Scope Listings: 331SCC 1003-15/64Partner File #0Partner: None



scope of accreditation - s-geexpertdirectory.s-ge.com › data › ...scc_accreditation.pdf · the...

Documents