schedule of rates - valid for rajasthan state...

11000038-HD-11370

SCHEDULE OF RATES - VALID FOR RAJASTHAN STATE (NORTH WEST RETAIL ZONE)

TL. NO. DESCRIPTION UNIT RATE(A)COMPOUND WALL/CULVERT/BLDG.

YARDLIGHT,TANKS, PUMP INSTALL.

EXCEPT DRIVEWAY & CANOPY

SITE SURVEY

2 SITE SURVEY UPTO 2000 SQM Lump Sum 6500.00

3 From 2001 to 10000SQM Lump Sum 8500.00

4 ACRE BEYOND 10000SQM Lump Sum 2750.00

5 SITE CLEARANCE Square Square Square Square MetresMetresMetresMetres 2.89

6 EXCAVATION IN EARTH<=3M Cubic Metres 100.00

7 EXCAVATION IN EARTH > 3M Cubic Metres 125.00

8 EXCAVATION-HARD ROCK<=3M Cubic Metres 693.00

9 EXCAVATION-HARD ROCK>3m Cubic Metres 927.00

10 SAND FILLING - LAYERS<150MM Cubic Metres 400.00

11 EARTH FILLING- LAYERS<200MM Cubic Metres 155.00

12 MURRUM FILLING- LAYERS<150MM Cubic Metres 291.00

Job includes carrying out survey at site, shown by HPCL engineer in-charge and establishing corners and boundaries at site & installing brick work benchmark duly plastered at all the corners for easy identification. Verifying the boundary details given by HPCL and computation of actual site layout plan are to bedone. Making temporary grid marking of the area under scope of survey, at every 5.0m interval in both the perpendicular directions. Recording the levels withrespect to the permanent B.M (to be established by survey team) using dumpilevel/theodolite. All existing relevant features like trees, electric lines, road,distance of the plot from milestone, culverts etc are to be plotted in the layout plan. Both tracing and soft copy in CAD duly recorded with levels and otherdetails to be submitted to HPCL alongwith 2 copies of blue prints of each tracing.

Same as item No:2 above but for 2001 SQM upto 10000 SQM

Same as item No:2 above but for every acre area or part thereof beyond 10000 SQM

Surface dressing of the ground including removing small trees, vegetation and any other objectionable item and making surface leveled and disposal of allrubbish, outside HPCL's premises to an unobjectionable place, as directed by the Engg.-In-Charge.

Earth work in excavation in all kind of soil including soft rock but excluding hard rock upto a depth of 3 m from the existing ground level. The job includesshoring, shuttering, bailing out rain water / sub soil water manually or by using appropriate capacity dewatering pump., ramming the bottom , dressing the sidesand bottoms and stacking the excavated earth not less than 1 m from the edge of excavation and then backfilling, spreading, watering and compaction,disposal of surplus earth within / outside HPCL's premises to any unobjectionable place all complete as per direction of Engg.-In-Charge. Any sheet pilingrequired to prevent excessive water seepage to tank area /foundation area will be paid separately as per approval of Engg.-In-Charge .Up to 3 m depth

Same as item no. 6 but for beyond 3 m depth

Description same as item no.6 except the soil will be hard rock and the excavation should be carried out by pneumatic tools like jack hammer, chisels, or byblasting taking all safety precautions and approvals as required. For 0-3 m depth

Same as item no.8 but for beyond 3 m depth

Supply and filling with clean silver / river sand of approved quality in layers of 150 mm each including spreading, compacting by hand ramming and wateringetc, all complete as per direction of Engg.-In-Charge. Measurement basis compacted thickness only.

Supplying and filling imported earth of approved quality in layers not exceeding compacted thickness of 200mm incl. Watering ,ramming, compacting, and ifrequired, rolling and re-rolling with power roller / manual roller / mechanical compactors to achieve maximum compaction, all complete as per direction of Engg.-In-Charge. The earth should be free from weeds, grass and other objectionable debris. Black Cotton soil shouldn't be used. Measurement basis compactedthickness only.

Supplying and filling imported murrum of approved quality in layers not exceeding compacted thickness of 150 mm inclusive spreading, Watering ,ramming,compacting, and if required, rolling and re-rolling with power roller / manual roller / mechanical compactors to achieve maximum compaction, all complete asper direction of Engg.-In-Charge. The murrum should be excavated from a quarry / mines, free from weeds, grass and other objectionable debris.Measurement basis compacted thickness only.

Vendor's Seal & Signature Eff. Date: 01-01-11 of 41

11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATE13 GRAVEL FILLING Cubic

Metres 445.00

14 GRANULAR SUBBASE -LAYERS<150MM Cubic Metres 285.00

15 PCC WORK-1:1.5:3 Cubic Metres 3768.00

16 PCC WORK-1:2:4 Cubic Metres 2955.00




20 DPC WITH BIT. & PCC 1:1.5:3 Square Metres 205.00

21 PCC 1:1.5:3-GROUT. MS STRUCT. Cubic Metres 3843.00

22 RCC1:1.5:3FOUND.PLNTH.RET. WAL Cubic Metres 3997.00

Supplying, laying and filling granular sub-base with sand gravel mix in the proportion of 1:1 for required compacted thickness in layers of 150 mm thick usingapproved quality gravel / stone aggregate and sand including watering, compacting with power / manual roller to achieve maximum compactness.Measurement basis compacted thickness only.

Note: For all cutting/excavation and filling jobs, it will be the responsibility and duty of the contractor to take joint initial levels with Engg.-In-Charge in all casesbefore commencing the work. The joint levels should be certified by the contractor as well as HPCL Engg.-In-Charge. The payments will be made basis theinitial levels and final levels taken jointly and certified. The payment for all cutting / excavation will be made at the lower rate applicable for 0 to 3 m and thehigher rate will be paid only for the portion beyond 3 m depth. If the contractor fails to take jointly certified levels, the levels as taken by HPCL Engg.-In-Chargeshall be treated as final and all payments will be released basis the levels so taken by the HPCL Engg.-In-Charge.

PCC WORK : Providing and laying PCC using graded stone aggregate of specified size and down. The job includes machine mixing, providing formwork,MS/plywood(minimum 19 mm thick) shuttering if directed by Engg.-In-Charge, placing, compacting by hand ramming , curing for a period of 14 days etc, allcomplete as per direction of Engg.-In-Charge. Removing of shuttering to be done carefully without such shock and vibration as to damage the PCC work. ForPCC 1:1.5:3 using 20 mm and down size graded stone aggregates. Vibrator to be used whenever directed by Engg.-in-Charge without any extra cost.

Same as Item No.15 but for PCC 1:2:4 using 20 mm and down size graded stone aggregates




PCC 1:1.5:3 FOR DPC Providing and laying 50 mm thick DPC in 1:1.5:3 mix with 6 to 12 mm size aggregate and water proofing compound of approved ISImake at the rate of 1 kg per bag of cement . Job includes all formwork, side MS/plywood(Minimum 19 mm thick) shuttering, proper compaction, hand rammingand curing for 14 days ,and supplying/applying a coat of hot bitumen of grade 60/70 on top, all complete including spreading of sand as required.

Providing and laying PCC 1:1.5:3 mix using 20mm and down stone aggregate for grouting Angles/MS Structurals. Other specs as per item no. 15. MSStructurals will be paid for separately.

Supplying and filling imported Gravel of approved quality in layers not exceeding compacted thickness of 150 mm inclusive spreading, Watering ,ramming,compacting, and if required, rolling and re-rolling with power roller / manual roller / mechanical compactors to achieve maximum compaction, all complete asper direction of Engg.-In-Charge. The Gravel should be free from weeds, grass and other objectionable debris. Measurement basis compacted thickness only.


11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATE

23 RCC1:1.5:3COL.SLAB.TIE.CLVRT…. Cubic Metres 4222.00

24 RCC1:1.5:3 FOR COPING Cubic Metres 4222.00

25 UNDER REAMED PILES-150 MM Running Metre 458.00




29 REINFORCEMENT STEEL IS:1786 Metric Ton 42000.00

30 BRICKMASONRY:SUBSTR.-NEW BRICK Cubic Metres 1876.00

31 BRICKMASONRY:SUBSTR-OLD BRICKS Cubic Metres 790.00

32 BRICKMASONRY:SUPERST.-NEWBRICK Cubic Metres 2111.00

33 BRICKMASONRY:SUPERST-OLDBRICKS Cubic Metres 820.00

REINFORCED CEMENT CONCRETE : Providing , Mixing, laying and placing RCC 1:1.5:3 mix with ordinary Portland cement using 20 mm and down sizegraded crushed stone aggregate including providing and fixing necessary plywood(minimum 19 mm thick)/ steel shuttering , scaffolding, machine mixing,compacting by mechanical vibrators (needle / skid etc), curing, hacking the surface to receive plaster using plastic / PVC sheet of thickness minimum20micron under RCC, as directedwherever required. etc. all complete. Machine mixing to be done without exception. Rate shall be exclusive of the cost ofsteel reinforcement, Concrete shall conform to relevant specifications of IS 456:2000 Latest Edition. For footings/foundations / plinth beam / floor beam /retaining wall etc.

Superplasticiser Rheobuild SP1 (Napthalene base) shall be dosed in mixing water after 50-70% of mixing water has been added in the mixer machine. TheDosage will be in the range of 0.6% to 0.8% by weight of cement (i.e. 300ml - 400ml per 50 kg. bag of cement) to get desired workability. EquivalentNapthalene based superplasticiser may be used in manufacturer's specified proportions/methods after prior approval of Engg.-in-Charge .

Same as Item No.22 but for Column / Tie beams / Chhajja / Lintel / roof slab / stair case / culvert slab etc.

Same as Item No.22 but for Coping

Earth work under pile foundation of specified dia till specified depth using hand auger or mechanical auger as approved in ordinary soil true to plumb, providingM 25 concrete for under reamed piles up to required depth with bulbs as directed and as per IS 2911 etc. complete as per design and direction of Engg.-In-Charge. Reinforcement steel shall be paid for separately. 150 mm diameter.

Same as Item No.25 but for 230mm dia

Same as Item No.25 but for 300mm dia

Same as Item No.25 but for 350 mm dia

REINFORCEMENT STEEL Supply ,fabrication, hoisting and placing in position HYSD reinforcement bars conforming to IS1786 -Latest Edition Grade FE415 /TMT bars of same grade as per detailed drawing and specifications including cutting, bending, cranking and tying with 18 SWG black annealed bindingwire complete. The rates shall be applicable for all heights and depths. Payment shall be made as per reinforcement drawings and with theoretical weights onlyincluding all authorised laps, chairs, spacers and hooks.

BRICK MASONRY WORKS Providing and constructing following brick masonry in CM 1:5 using locally available bricks of Class designation 75 (minimum) and conforming to IS 1077:1986 including providing all openings and projections , raking the joints to 1 cm deep, scaffolding, soaking of bricks in water prior to use and curing etc all complete as per specifications .SUB STRUCTURE Providing and laying brick masonry as above for foundation below DPC level.

SUB STRUCTURE below DPC level: Same as item no. 30 but using old bricks taken out from demolished masonry. Rate includes removing mortars andcleaning of bricks etc. complete. Once the demolition is over, the party has to take out the usable good bricks and stack them properly to enable Engg.-In-Charge to assess the quantity of bricks for future reference and calculation. Once the assessment is made it is duty of the contractor to obtain certificate fromEngg.-In-Charge about the quantity of usable bricks available before these bricks are put to use. In absence of certificate no payment will be made. However,in no case the old bricks shall be used without the assessment of quantity and clearance to use the old bricks is given by the Engg.-In-Charge.

SUPER STRUCTURES. Providing and laying brick Masonry as item no. 30 but for superstructure above DPC level including scaffolding.


11000038-HD-11370



34 PARTITION 115-NEWBRICK MASONRY Square Metres 345.00

35 RANDOMRUBBLE MASONRY-SUBSTR. Cubic Metres 1515.00

36 RANDOMRUBBLE MASONRY-SUPERSTR. Cubic Metres 1809.00

37 MASONARY WITH CC BLOCKS Cubic Metres 3400.00

38 DRESSED STONE MASONARY Cubic Metres 2718.00

39 RUBBLE PITCHING – 230 MM THICK Square Metres 163.00

40 RUBBLE PITCHING – 150 MM THICK Square Metres 127.00

41 RUBBLE SOLING – 230 MM THICK Square Metres 95.00

42 RUBBLE SOLING – 150 MM THICK Square Metres 80.00

SUPER STRUCTURE : Same as item no. 30 but using old bricks taken out from demolished masonry. Rate includes removing mortars and cleaning of bricksetc. complete. Once the demolition is over, the party has to take out the usable good bricks and stack them properly to enable Engg.-In-Charge to assess thequantity of bricks for future reference and calculation. Once the assessment is made it is duty of the contractor to obtain certificate from Engg.-In-Chargeabout the quantity of usable bricks available before these bricks are put to use. In absence of certificate no payment will be made. However, in no case the oldbricks shall be used without the assessment of quantity and clearance to use the old bricks is given by the Engg.-In-Charge.

Same as item no.30 but for 115 mm thick in partition walls in CM 1:4. Rate to include providing 75 mm thick RCC 1:1.5:3 bands using 2 nos 8 mm diaTorsteel reinforcement at every 1 M height of wall including plywood/ MS shuttering. Steel reinforcement shall be paid for separately.

Providing and constructing random rubble masonry with good quality stone in CM 1:5 for substructure & superstructure as per IS 1597 part 1, latest edition. Rate to include soaking stones, raking the joints to 1 cm deep and curing complete. One Through / Bond stone shall be provided for every square meter of facing , evenly distributed in a staggered pattern. They shall have about 0.03 sqm in face area and shall have a tailing for the full width of masonry upto 600mm.

If masonry wall is over 600mm thick, a line of headers (not less than 450mm length ) overlapping each other by 150mm shall be laid. Bond stones shall be distinctly marked on its face during construction for verification. Quoin / key / corner stone shall not be less than 0.03cum in volume. FOR SUBSTRUCTURE

Same as item no. 35 but FOR SUPERSTRUCTURE including scaffolding

Masonary with CC blocks of size 400mmx200mmx200mm in CM 1:3. The concrete blocks to be moulded with mix 1:3:6 using 1 part of cement, 3 parts of course sand and 6 parts of 40mm downsize graded stone aggregate The job includes casting of CC blocks with the help of moulds by machine mixed mix of 1:3:6 in steel/wooden moulds, placing, compacting by hand ramming, pond curing of the blocks for a period of 14 days etc, all complete. Care to be taken while removing of moulding to be done carefully without such shock and vibration as to damage the block.. Masonary to be carried out with these blocks in CM 1:3 (1 part of cement and 3 parts of course sand). Scope of job includes raking the joints to 1 cm deep, scaffolding, curing etc all complete as per specifications. The masonary to be done in the fashion similar to the brick masonary. 12.0MM Plastering shall be done on the masonary, which shall be paid separately under plastering head. .

Providing and constructing dressed stone masonry with good quality hard dressed stone in CM 1:5 for substructure & superstructure as per IS 1597 part 1, latest edition. Rate to include soaking stones, raking the joints to 1 cm deep and curing complete. One Through / Bond stone shall be provided for every square meter of facing , evenly distributed in a staggered pattern. The stone masonary wall should have a facing of dressed stone on one side and the face should be at least 150mm x 150mm. No plaster should be done on such face.

If masonry wall is over 600mm thick, a line of headers (not less than 450mm length ) overlapping each other by 150mm shall be laid. Bond stones shall be distinctly marked on its face during construction for verification. Quoin / key / corner stone shall not be less than 0.03cum in volume.

Providing rubble pitching including surface dressing, making required slope . Rate to exclude flush pointing which will be paid for separately. 230 mm thick

Same as item no. 39 but for 150 mm thick

Providing rubble soling including surface dressing, making required slope, soaking the rubbles before laying, packing the gaps using small size rubble / stone/ murrum/stone dust/sand, and hand ramming / using mechanical roller / compactor as per site requirement all complete. 230 mm thick

Same as item no. 41 but for 150mm thick


11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATE43 FLUSH POINTING-1:3 CM MIX Square

Metres 42.00

44 RAISED POINTING-5MM,1:3CM MIX Square Metres 58.00

45 RAISED POINTING-12MM,1:3CM MIX Square Metres 92.00

46 BRICK FLAT SOLING:SINGLE LAYER Square Metres 176.00

47 BRICK FLAT SOLING:DOUBLE LAYER Square Metres 343.00

48 BRICK ON EDGE SOLING-4.5” THK. Square Metres 170.00

49 PLASTERING 20MM THK. SANDFACED Square Metres 105.00

50 PLASTERING 12 MM THICK Square Metres 75.00

51 PLASTERING 6 MM THICK Square Metres 59.00

52 WEEP HOLES 75 MM DIA PVC Running Metre 180.00

53 STRUCT. STEEL:ANGLE IRON POST Metric Ton 57000.00

54 STAINLESS STEEL RAILG.& OTHERS KG 335.00

55 PIPE RAILING-IS1239/IS1161 Running Metre 390.00

Providing flush pointing in rubble pitching with 1:3 cement mortar including curing etc. complete.

Providing raised pointing 5 mm with CM 1:3 along the joints of exposed stone masonry. The joints shall be raked & cleaned, curing etc. all complete.

Providing raised pointing 12 mm with CM 1:3 along the joints of exposed stone masonry. The joints shall be raked & cleaned, curing etc. all complete.

Providing Brick soling 3.5" thick (including sand bedding), surface dressing, making required slope, soaking the bricks before laying, packing the gaps usingsand and watering etc all complete.

Double layer Brick flat soling: Specifications same as item no. 46. Thickness 7.0"

Providing Brick on edge soling 4.5" thick (including sand bedding), surface dressing, making required slope, soaking the bricks before laying, packing thegaps using sand and watering etc all complete.

Providing and laying average 20 mm thick sand faced cement plaster in ratio 1: 3 :1(cement; fine sand : coarse sand) in two coats. Rate to include use ofwater proofing compound as per manufacturer's recommendation. Rate shall include providing necessary scaffolding, chicken wire mesh at all joints of brickand concrete surfaces, with a minimum overlap of 150 mm in all directions and curing complete. No extra payment shall be made for additional thickness ifrequired to achieve perfect line and level. The job includes cleaning, wetting of surface before plastering, curing etc all complete. Required grooves to beformed as directed.

Same as item no.49 but 12 mm thick plaster in ratio 1: 3 :1(cement; fine sand : coarse sand) in single coat.

Same as item no.49 but 6 mm plaster in 1:4 (cement: fine sand) to ceiling surfaces / beams etc as required.

WEEP HOLES Providing, fabricating and installing in place, 75 mm dia 6Kg / sqcm PVC Pipes of various lengths & at places as approved and directed atsite on the masonry wall for water drainage. The pipes shall be fixed with nylon jali using resin/glue on inside end of wall.

Supply, fabrication , erection and grouting of MS structurals in PCC 1:1.5:3 as per direction of Engg.-In-Charge. Rate to include fabrication of the post as perthe specification, erecting, placing, grouting to required depths and painting of the posts with two coats of Synthetic Enamel over two coats of Red OxidePrimer. Excavation and PCC shall be paid separately.

Supply, fabrication, erection, giving finish and grouting of Stainless Steel (SS-304) railing, grab bar, balustrade, island guards & others made out of 1.6 to 3mm wall thickness pipes of up to 50 NB dia./50mm square tubes and upto 6 mm thick SS plates including fasteners. The job shall be completed in strictconformity to architectural drawing with neat workmanship. The location of joints, junctions and joineries shall be indicated in a drawing prepared by thecontractor and prior approval of HPCL shall be taken for the same. Generally joints will not be allowed except at joining points of other members. The weldingprocedure,tools and machinery and electrodes shall be as per BIS specifications for SS-304 fabrication. Payment shall be made basis weight of finished SSpipes/tubes/plates only with no allowances for wastage, nuts and bolts etc. Contractor has to submit purchase proof of SS pipes. Additionally samples will bedrawn from the SS sections so used and will be tested in a reputed laboratory for conformity to SS-304 parameters and physical details at contractor's cost.


11000038-HD-11370



56 CHAINLINK FENCE,50x50,10SWG GI Square Metres 479.00

57 BARBED WIRE FENCING ON Y ANGLE Running Metre 122.00

58 BARBED WIRE FENCING Running Metre 169.00

59 MS GRILL / STAIR CASE Metric Ton 57000.00

60 MS GRATING& ISLAND COVER.FRAME Metric Ton 57000.00

61 RCC HUME PIPE, NP3, 1000 NB Running Metre 4989.00


Same as item no.61 but for diameter 600 mm NB


Same as item no.61 but for diameter 450mm NB





Supply and fixing of 40 NB medium duty MS pipes conforming to IS 1239 /IS 1161 YST 21 latest addition for top and bottom railings to the angle iron posts forfixing the edges of the chain link fencing. Rate to include fabricating, cutting, bending of the MS pipe where ever necessary. Supply and fixing of the requiredsize MS clamps at every post, with required size nuts and bolts and painting the railing with two coats of Red oxide Primer and two coats of Synthetic enamelpaint after necessary cleaning and scrapping.

Supply and fixing of 50 x 50mm opening size 10 SWG GI chain link fencing to the angle iron post with 8 SWG GI hooks and nuts and railing with 14 SWG GIcontinuous wire up to a height of 1.8 m from the ground level. Rate to include unrolling the bundle, erecting, tightening and fixing at 300 mm C-C on thevertical portion of the posts to every top and bottom railing with 14 gauge GI wire complete as per drawing. Angle post to be paid separately as per relevantitem.

Providing and fixing barbed wire in 10 rows horizontal with two ply 12 SWG GI barbed wire fencing with barbes @ 100mm c/c using GI hooks etc allcomplete to angle / MS structurals posts grouted as per direction of Engg.-In-Charge, complete as per drawing.. MS structurals / Angle post shall be paid forseparately. For payment purpose measurement shall be taken for the length of plot boundary. No measurement shall be taken for 10 rows individually.

Providing and fixing barbed wire in 13 rows horizontal and 2 diagonals with two ply 12 SWG GI barbed wire fencing with barbes @ 100mm c/c using GIhooks etc all complete to angle / MS structurals posts grouted in CC 1:1.5:3 as per direction of Engg.-In-Charge, complete as per drawing. MS structurals /Angle post shall be paid for separately. For payment purpose measurement shall be taken for the length of fencing. No measurement shall be taken for 13rows individually.

Supply, installation and fixing of Prefabricated MS grill / Monkey Ladder/ Stair case/ baluster/ MS Bars (IS 2062 Latest Edition) on compound wall using MSstructurals / bars / hollow sections / strips / pipes etc as per design given by HPCL and direction of Engg.-In-Charge. Rate to include erection, grouting ofposts in PCC 1:1.5:3, painting by two coats of red oxide primer and two coats of synthetic enamel of approved shade. Grouting PCC to be paid separately asper relevant item.

Providing, fabricating, welding and fixing structural steel in position with angle iron / flats / tees / squares / SHS tubes conforming to IS 4923 : 1997, plates etcas per design and direction given by Engg.-In-Charge for drain grating, manhole frames, gratings ,tree guards, Island Covering Frame etc, as per requirement.Job includes all necessary grouting, supply and fixing of handles, nuts - bolts etc, painting the grating with 2 coats of approved synthetic enamel paint, over acoat of red oxide primer.

Supplying, laying, aligning and joining following size NP3 class RCC Hume pipes of approved make conforming to IS-458 Latest Edition, as per direction ofEngg.-In-Charge. Rate to include excavation to required depth as per direction of Engg.-In-Charge (minimum earth cushion to be ensured) and providing 4"thick and (Outer Dia in mm+200mm) wide PCC 1:5:10 below the Hume pipe as bed, 4" thick fine sand cushion all around the Hume pipe, backfilling,compaction, curing and testing joints against leakage.

Rate to include supplying and fixing of required collars and fixing the same by using cement mortar 1:3. All pipes must be new and perfectly sound, free fromcracks, cylindrical, straight and of standard nominal diameter and length with even texture. Test certificates from manufacture shall be submitted and approvedby Engg.-In-Charge before use, all complete. Diameter 1000mm NB


11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATE66 RCC HUME PIPE, NP3, 200 NB Running

Metre 815.00Same as item no.61 but for diameter 200mm NB


Same as item no.61 but for diameter 150mm NB and NP-2

68 ANTI TERMITE TREATMENT Square Metres 275.00

69 CERAMIC TILE FLOORING Square Metres 641.00

70 VITRIFIED TILE FLOOR NLT 700 Square Metres 1163.00

71 VITRIFIED TILE FLOOR NLT 1000 Square Metres 1584.00

Same as item no. 70 but Basic rate not lower than Rs. 1000/- per sqm

72 VITRIFIED TILE FLOOR - SINTRA Square Metres 1615.00

73 VITRIFIED TILE FLOOR-S&P GREY Square Metres 1537.00

74 VITRIFD. TILE FLR.-SNOW CARARA Square Metres 1992.00

75 VITRIFD. TILE FLR.-OLYMPOUS Square Metres 1381.00

76 VITRIFIED TILE FLRG.-SAVONA Square Metres 1537.00

Same as item no. 70 but of NITCO, Savona of size 600x600 mm or Approved Equivalent

77 VITRIFD. TILE FLRG.-OCEAN MIST Square Metres 2252.00

Providing anti-termite treatment including diluting and injecting chemical emulsion / NEEM based solution and creating a continuous chemical barrier underand all around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor, along the external perimeter ofbuilding, expansion joints, over the top surface of consolidated earth on which apron is to be laid, surroundings of pipes and conduits etc. complete as perspecification using Chlorpyriphos emulsifiable concentrate (20%) in 1% concentration or as specified by manufacturer.

Plinth area of building at ground floor only shall be measured for payment. The work shall be carried out by a qualified agency as approved by Engg.-In-Charge. Contractor will have to submit 10 years guarantee bond on Rs. 100/- stamp paper for the treatment.

Providing and laying matt finish Ceramic tiles of approx 8 mm thick of size as specified in flooring. The tiles used should be of KAJARIA make of Group - IV orequivalent group of approved makes. The tiles should be of first quality of approved make and shade and free from cracks, warpage, fissures and flakes withstraight edges and perfect corner laid at right angle as per design & pattern over a bedding of cement mortar 1:5 of average 30 mm thick, finishing the jointsneatly with white cement mixed with matching colour pigment and finish in all respect with all material and labour complete

giving required slope as directed by Engg.-In-Charge. If necessary, surface unevenness shall be filled up with brick ballast manually compacted with wateringetc. complete as per instructions of Engg.-In-Charge without extra cost. Tiles size shall not be less than 300x300 mm. Basic Rate - Not lower thanRs.350/sqm

Providing and laying polished vitrified Ceramic tiles of minimum 8 mm thick of size as specified in flooring. The tiles used should be of KAJARIA make orequivalent approved makes. The tiles should be of first quality of approved make and shade and free from cracks, warpage, fissures and flakes with straightedges and perfect corner laid at right angle using approved PVC corner spacers as per design and pattern over a bedding of cement mortar 1:5 of average 30mm thick, finishing the joints neatly with white cement mixed with matching colour pigment/ Ball Adhesive and finish in all respect with all material and labourcomplete giving required slope as directed by Engg.-In-Charge.

Tiles size shall vary between 300x300 mm (minimum) and 600X600 mm (maximum) as directed by Engg.-In-Charge. If necessary, surface unevenness shallbe filled up with brick ballast manually compacted with watering etc. complete as per instructions of Engg.-In-Charge without extra cost. Basic rate not lowerthan Rs. 700/- per sqm.

Same as item no. 70 but of H & R Johnson(Marbonite), Sintra of size 600x600mm or Approved Equivalent

Same as item no. 70 but of H & R Johnson(Marbonite), S&P Grey of size 600x600 mm or Approved Equivalent

Same as item no. 70 but of H & R Johnson(Marbonite), Snow Carara of size 900x900 mm or Approved Equivalent

Same as item no. 70 but of H & R Johnson(Marbonite), Olympous of size 600x600 mm or Approved Equivalent


11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATESame as item no. 70 but of NITCO, Ocean Mist of size 800x800 mm or Approved Equivalent

78 VITRI. TILE FLRG.-NOVARA BEIGE Square Metres 1927.00

79 GRANITE TILE FLOOR 10 MM Square Metres 2063.00

80 MARBLE FLOORING Square Metres 672.00

81 KOTA STONE FLOORING / STEPS Square Metres 586.00

82 IPS FLOORING Square Metres 323.00

83 EUROCON TILE-WALKWAY NLT 500 Square Metres 916.00

84 EUROCON TILE-WALKWAY NLT 400 Square Metres 780.00

85 CHEQUERED TILES Square Metres 760.00

86 CERAMIC TILE SKIRTING Running Metre 95.00

Same as item no. 70 but of NITCO, Novara Beige of size 600x600 mm or Approved Equivalent

Providing and laying minimum 10 mm thick granite tile of minimum size of 300 mm x 300 mm (Basic rate not lower than Rs. 1000/- per sqm) in flooring ofapproved shade and free from cracks, warpage, fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over abedding of cement mortar 1:5 of average 30 mm thick finishing the joints neatly with white cement mixed with matching colour pigment and finish complete inall respects and all material and labour complete giving required slope as directed by Engg.-In-Charge.

If necessary, surface unevenness shall be filled up with brick ballast manually compacted with watering etc. complete as per instructions of Engg.-In-Chargewithout extra cost.

Providing and laying 10 mm thick white marble (Basic rate not lower than Rs 700/sqm) of size of 1000 mm x 1000 mm in flooring of approved shade andfree from cracks, warpage, fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a bedding of cementmortar of 30 mm thick CM 1:5 finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect and all material andlabour complete. If necessary, surface unevenness shall be filled up with brick ballast manually compacted with watering etc. complete as per instructions ofEngg.-In-Charge without extra cost.

Providing and fixing 20 mm thick Kota stone slabs with 25mm bedding CM 1:3, cement slurry and machine polishing on one side. The tiles should be of firstquality and free from cracks, warpage, fissures and flakes with straight edges and perfect corner laid at right angle as per design and pattern over a beddingof cement mortar 1:5 of average 30 mm thick, finishing the joints neatly with white cement mixed with matching colour pigment and finish in all respect with allmaterial and labour complete, giving required slope as directed by Engg.-In-Charge.

If necessary, surface unevenness shall be filled up with brick ballast, manually compacted with watering etc. complete as per instructions of Engg.-In-Chargewithout extra cost. In case of step slabs, one piece slab to be used. The slab shall not have exposed sharp edges. The exposed edges shall be grinded andpolished in smooth curvature.

Providing mixing and laying 50 mm thick Indian Patent Stone flooring in PCC 1:2:4 mix concrete with 12 mm and down size graded crushed aggregateincluding providing and fixing 4 x 25 mm size glass strips in1 metre x 1 metre panels, casting the concrete compacting and finishing the surface smooth usingcement slurry.

Supply and fixing concrete tile of EUROCON make of approved shade of 20mm thickness for flooring including providing 20mm thick 1:5 cement mortarbed and a floating coat of neat cement slurry, finishing the joints with white cement mixed with matching colour pigment, cleaning the surface with dilutesulphuric acid etc. Complete. If necessary, surface unevenness shall be filled up with brick ballast manually compacted with watering etc. complete as perinstructions of Engg.-In-Charge without extra cost. Basic rate : Not lower than Rs. 500/sqm.

Same as item no.83 but for treads and risers Basic rate: Not lower than Rs. 400/sqm

Supply and fixing NITCO make 300x300 mm External Mosaic chequered tiles Design No. RY36S of approved shade of 25 mm thickness includingproviding 20mm thick 1:5 cement mortar bed and finishing the joints with white cement mixed with matching colour pigment, cleaning the surface neat etc.complete. If necessary, surface unevenness shall be filled up with brick ballast manually compacted with watering etc. complete as per instructions of Engg.-In-Charge without extra cost.


11000038-HD-11370



87 VITRIFIED TILE SKIRTG. NLT 700 Running Metre 163.00

88 VITRIFIED TILE SKIRTG NLT 1000 Running Metre 217.00

89 POLISHED GRANITE SKIRTING Running Metre 217.00

90 POLISHED MARBLE SKIRTING Running Metre 163.00

Same as Item No.86 but Marble skiritng (10mm thick) of approved colour and shade.

91 POLISHED KOTA STONE SKIRTING Running Metre 93.00

92 CERAMIC TILES DADO IN TOILET Square Metres 593.00

93 DESIGNER TILES DADO IN TOILET Square Metres 720.00

94 DESIGNER TILES DADO IN TOILET Square Metres 1175.00

95 TERRACOTTA TILES Square Metres 645.00

96 WALL TILES DADO-RIVIERA Square Metres 701.00

97 WALL TILES DADO-BINACO CARARA Square Metres 701.00

98 WALL TILES DADO-CREMA ROYALE Square Metres 701.00

Providing and fixing tile skirting of approved shade and make of First quality free from crack fissures & flakes with straight edges & perfect corners fixed atright angles of 150 mm height using cement mortar bedding 1:3 and fixed with neat cement slurry and finishing the joint with white cement mixed withmatching colour pigment . Rate to include necessary chipping if required in masonry / concrete, so that skirting is projecting uniformly 6mm from plasteredface. All vertical joints of skirting should match with floor tiles spacing uniformly complete as per direction of EIC.

CERAMIC TILES SKIRTING : Kajaria make of gr. IV (8mm thick).

Same as Item No.86 but Polished vitrified ceramic tile 8mm thick skirting. Basic rate-Not lower than Rs.700/sqm

Same as Item No.86 but Polished vitrified ceramic tile 8mm thick skirting. Basic rate-Not lower than Rs.1000/sqm

Same as Item No.86 but Granite skirting (10mm thick) of approved colour and shade.

Same as Item No.86 but Kota Stone skirting (20mm thick) of approved colour and shade.

Providing and fixing minimum 5 mm thick ceramic tiles of minimum 200 x 100 mm size of approved shade and make First quality , free from crack fissures &flakes with straight edges & perfect corners fixed at right angles as per the design and pattern required, including applying 12mm thick backing plaster in 1:3CM and fixing the tiles with neat cement paste and finishing the joints with white cement mixed with colouring pigments to match the colour of tiles properlycured & finished in all respect.

Designer Tiles with suitable Borders on top and middle; Other specifications same as item no.92

Same as item no. 92 but polished vitrified tiles.Tiles size shall vary between 300x300 mm (minimum) and 600X600 mm (maximum) as directed by Engg.-In-Charge.

Providing and fixing terracotta tiles minimum 3 mm thick and minimum 75x150 mm size of approved shade and make First quality , free from crack fissures &flakes with straight edges & perfect corners fixed in true line & level as per the design and pattern advised by Engg.-In-Charge. Rate includes applying 12 mmthick backing plaster in 1:3 CM in true line & level, properly cured & rough finished. Fixing the tiles with neat cement paste and finishing the joints withterracotta paint in a neat & aesthetic way complete in all respects. Approved Make of Tiles: Dazzle Designer Tiles of Milan - Terracotta smooth finish

WALL TILES DADO: Providing and fixing minimum 5 mm thick wall tiles of approved shade, gloss and finish of size 600 x 300 mm size of approved shadeand make First quality , free from crack fissures & flakes with straight edges & perfect corners fixed at right angles as per the approved design and patternrequired, including applying 12mm thick backing plaster in 1:3 CM and fixing the tiles with neat cement paste and finishing the joints with white cement mixedwith colouring pigments to match the colour of tiles properly cured & finished in all respect.

Make: H & R Johnson (Marbonite) - Riviera or Approved Equivalent

Same as item no. 96 but Make: H & R Johnson (Marbonite) - Binaco Carara or Approved Equivalent

Same as item no. 96 but Make: H & R Johnson (Marbonite) - Crema Royale Approved Equivalent


11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATE99 WALL TILES DADO-RECTIFIED Square

Metres 655.00

100 GRANITE SLAB-18MM GREY Square Metres 2400.00

101 SILL SLAB Square Metres 2860.00

102 CURTAIN WALL-WITH FIXING LOGO Square Metres 2375.00

103 CURTAIN WALL-W/O FIXING LOGO Square Metres 2325.00

104 WATER PROOFING-BRICKBAT COBA Square Metres 363.00

105 ROOF-THERMAL&MOIST. PROTECTION Square Metres 380.00

106 KERB BLOCKS 300x140x230mm Running Metre 120.00


Providing and fixing not less than 18 mm thick pre polished water cut grey granite slabs over steps or as advised including providing 25mm thick bed cementmortar 1:4 (1 cement : 4 coarse sand) ,as per design incl. chamfered edges and polished nosing. Rate includes 8 mm thick polished black granite tile work innosing as per drawing. Job includes finishing the joints with white cement mixed with matching colour pigment.

Providing and laying machine cut and machine polished 18 mm thick jet black granite slab in one piece over a bedding of 20 mm thick 1:5 CM for window sills.The granite slab shall not have exposed sharp edges. The exposed edges shall be grinded and polished in smooth curvature.

Supply and fixing minimum jet black granite slabs machined cut and polished on curtain wall by providing bedding of cement mortar and neat cement backingof average 20mm thick in CM 1:3, filling of interspaces with black cement so as to match the colour of granite. The slabs shall be preferably cut from thesingle rock source to have uniform grain structure free from cracks, fissures and flakes with straight edges and perfect corners.

The slab should have following minimum dimensions. Width = 0.8 M, Length = 1.2M, Thickness = 18 mm, The slabs have to be fixed by taking services ofhighly skilled mesons true to plumb complete in all respect. Granite slabs used shall not be more than six nos. In case of increase in no. of slabs prior approvalof Engg.-In-Charge shall be obtained.

With fixing LOGO supplied by HPCL: Including fixing of logo and electrification for the same. Granite used shall be minimum 18 mm thick.

Same as item no.102 but without fixing LOGO: To leave provision for fixing the logo. Granite used shall be minimum 18 mm thick.

Same as item no. 96 but Make: H & R Johnson (Marbonite) - Rectified or Approved Equivalent

BRICKBAT COBA ON TERRACE Providing and laying integral cement based water proofing of average 100 mm thick as per specifications given. The jobincludes Cleaning of RCC slab and applying neat cement slurry mixed with waterproofing compound, providing and laying brickbat coba in CM 1:4 mixed withwater proofing compound and curing for a period of 24 hours, laying of 25 mm thick PCC 1:1.5:3 mix with 6 mm and down size coarse aggregate and waterproofing compound, finishing smooth, making half round vata at the junction of parapet wall and slab and curing for 10 days.

Contractor will be required to submit a guarantee on Rs. 100/- stamp paper for a period of 10 years in respect of performance of waterproofing.

THERMAL & MOISTURE PROTECTION (roof water proofing) : Providing and laying the following roof water proofing treatment consisting of (i) First layer of50 mm thick CC 1:3:6 over roof slab laid to falls and slope on minimum 1:100 and finished smooth to receive water proofing membrane. (ii) Second layer of3mm thick polyester reinforced modified bituminous water proofing membrane including primer coat as per manufacturer's specification. (iii) Third layer of 150micron polythene sheet laid over the water proofing membrane.

(iv) final layer of 25mm thick 600mm x 600mm precast concrete tiles of M-25 grade with 10mm grooves filled up with cold bitumen to form 600x600mm panelsas contraction joints all material and labour complete in all respect. Contractor will be required to submit a guarantee on Rs. 100/- stamp paper for a period of10 years in respect of performance of waterproofing.

Providing and fixing at or near ground level smooth finished pre-cast, cement concrete blocks in kerbs, edging etc. The block may be precast at site or anyother approved place in PCC 1:1.5:3 using steel mould in approved pattern and setting. The blocks shall be laid / fixed in position using CM 1:3. The jobincludes machine mixing, use of vibrator, all labour, material laying etc complete. If directed excavation upto 200 mm shall be carried out without any extracost. Kerb block of approx 300x140x230mm size. (length x thickness x height). The face corner of the kerb block will be made rounded as per instructions.


11000038-HD-11370






111 PAINTING WORKS-WHITEWASH Square Metres 6.50

112 APEX PAINTING Square Metres 98.00

113 OIL BOUND DISTEMPER Square Metres 43.00

114 ACRYLIC EMLSN. PAINT-INTERIOR Square Metres 76.00

115 ECONOMY EMLSN. PAINT-INTERIOR Square Metres 42.00

116 ACRYLIC EMLSN. PAINT-EXTERIOR Square Metres 70.00

117 WATER PROOF CEMENT PAINT Square Metres 38.00

118 SANDTEX MATT PAINT Square Metres 71.00

Same as item no. 106 but Kerb block of approx 300x140x300mm size. (length x thickness x height).

Same as item no.106 but Kerb block of approx 200x100x400mm size. (length x thickness x height).

Same as item no. 106 but Kerb block of approx 200x150x300mm size. (length x thickness x height).

Same as item no.106 but Kerb block of approx 250x150x450mm size. (length x thickness x height). Every fifth block shall have 115x95x40 mm cavity as perapproved drawing with retroreflective red paint making the spacing of such painted cavities @ 1 m c/c.

All material required for execution of painting work shall be obtained direct from approved manufacturers and shall be brought to the sites in their drums / cans/ bags etc with seals unbroken. No thinner shall be used unless approved by Engg.-In-Charge. The paint shall be applied by using brush, roller or spraying asdirected. The paint etc shall be applied only after proper surface preparation by removing all dirt, dust, mortar droppings, another foreign matter, loose scale byusing brooms, wire brush, sand paper etc as per requirement and direction complete.

All holes, cracks, patches etc shall be made good with material similar to that of the surface. The painting shall be applied in specified coats or more so as toobtain the desired finish. If additional coats are required to obtain uniform and smooth finish, the same shall be carried out at no extra cost. The job includesprovision of scaffolding using safety precautions, curing etc as required.

WHITEWASH : Providing and applying 3 coats of white wash to plastered and concrete surfaces by mixing binder, , glue, indigo etc. complete as per IS:712- Latest Edition.

APEX PAINTING : Providing and applying 2 coats of Apex paint to all the exterior surfaces including a coat of primer as per manufacturer's specificationcomplete. General specifications/guidelines given under WHITEWASH item also to be followed, as applicable.

OIL BOUND DISTEMPER Providing and applying 2 coats ( first coat with brush and final coat with Roller) of OBD of approved make and shade on allsurfaces and heights to give an even shade including priming coat and compatible putty etc. complete. General specifications/guidelines given underWHITEWASH item also to be followed, as applicable.

ACRYLIC EMULSION PAINT (INTERIOR GRADE) Providing and applying 2 coats ( first coat with brush and final coat with Roller) of Acrylic Emulsion paintof approved make and shade on all surfaces and heights to give an even shade including primer and compatible putty. General specifications/guidelines given under item no. 111 also to be followed, as applicable.

Providing and applying 2 coats ( first coat with brush and final coat with Roller) of approved shade Economy Emulsion (Bison Super Emulsion of Beger orapproved equivalent) paint on all surfaces and heights to give an even shade including primer and compatible putty. General specifications/guidelines givenunder item no.111 also to be followed, as applicable.

ACRYLIC EMULSION PAINT (EXTERIOR GRADE) Providing and applying 3 coats of acrylic anti fungal cement paint including primer of BERGER(Weathercoat) or approved equivalent make and shade to all the exterior surfaces as per manufacturer's specifications. General specifications/guidelinesgiven under item no.111 also to be followed, as applicable.

WATER PROOF CEMENT PAINT Providing and applying 2 coats of water proof cement paint of SNOWCEM INDIA make and of required shades on allsurfaces and heights to give an even shade. General specifications/guidelines given under item no.111 also to be followed, as applicable.


11000038-HD-11370



119 SYNTHETIC ENAMEL PAINT-WALL Square Metres 58.00

120 SYNTHETIC ENAMEL PAINT-STEEL Square Metres 65.00

121 SYNTHETIC ENAMEL PAINT-WOOD Square Metres 70.00

122 PLASTIC EMULSION PAINT Square Metres 64.00

123 POP -WALL,BEAM,COL.&CEILING Square Metres 55.00

124 POP -MOULDING Running Metre 85.00

125 FLUSH DOOR 34 MM THICK Square Metres 1750.00

126 TEAK WOOD DOOR FRAME Running Metre 550.00

127 ANOD. AL. GLZ. DOOR-12MM GLASS Square Metres 3004.00

SANDTEX MATT Providing and applying 2 coats of Sandtex matt paint of SNOWCEM INDIA make and of required shades on all surfaces and heightsto give an even shade including primer coat of snowcem plus. General specifications/guidelines given under item no.111 also to be followed, as applicable.

SYNTHETIC ENAMEL PAINT OVER WALL Providing and applying 2 coats of synthetic enamel paint 1st quality of approved manufacturer and of requiredshades on wall to give an even shade including a primer coat. General specifications/guidelines given under WHITEWASH item also to be followed, asapplicable.

SYNTHETIC ENAMEL PAINT OVER STEEL SURFACE Providing and applying 2 coats of synthetic enamel paint 1st quality of approved manufacturerand shades on steel surface to give an even shade including two coats of red oxide primer. General specifications/guidelines given under item no.111 also to be followed, as applicable.

SYNTHETIC ENAMEL PAINT OVER WOOD WORK Providing and applying 2 coats of synthetic enamel paint 1st quality of approved manufacturer andshades on wood surface including a coat of primer to give an even shade. General specifications/guidelines given under item no.111 also to be followed, asapplicable.

PLASTIC EMULSION PAINT: Providing and applying 2 coats ( first coat with brush and final coat with Roller) of Plastic Emulsion paint of approved makeand shade on all surfaces and heights to give an even shade including primer and compatible putty. Approved Make: Asian/Nitco / Nerolac. Generalspecifications/guidelines given under item no.111 also to be followed, as applicable.

ON WALL & CEILING : Providing and applying Plaster of Paris(POP) punning on walls, ceilings, beams and columns to bring the surface in plumb line andlevel including making the surface smooth etc. complete. The rate shall include preparing the surface with POP and compatible putty to give a smooth finishas per approval of the Engg.-In-Charge. Rate to include cost of scrapping, neeru finish etc. complete if needed.

Plaster of Paris (POP) Moulding : Providing and fixing moulding of size 3" x 3" in the edge of the wall and the ceiling with necessary hardware, properlyfinished, all material and labour complete.

Supply and fixing termite resistant ISI marked prelaminated solid core type wooden flush doors as per IS 2202 Part 1:1999 (Plywood face panels) finished with1mm thick laminates of approved colour/pattern on both sides and of total thickness not less than 34 mm. Both side faces and all the edges shall be polishedin approved colour/pattern as per directions of EIC. Rate shall be inclusive of all labour, fixing the door in frame in true plumb, line and level & supply and fixing heavy duty 3 nos. stainless steel (SS) hinges of100 mm length, 2 nos. SS aldrops of 200 mm length one from inside and other from outside, SS tower bolt of 200 mm length and door stopper etc. allcomplete. Approved Make: Kitply/ Anchor Board/ Wonder wood/ Duro/ National or equivalent. Teak wood door frame will be paid for separately as per relevant item.

Supply and fixing seasoned (IS 1141:1993 latest edition) pretreated (IS 401 : 2001 latest edition) teak wood frame for flush door installation and of 125x63mm nominal cross section. The timber will be sound, straight and free from sap, radial cracks, decay, fungal growth, boxed heart, pitch pockets, borer holes,splits, loose knots, rots or any other flaws. Rates are inclusive of 25x10 mm teakwood beading of same specification and matching colour polish coveringjunction of frame and wall in true line, level and finish.

Rate to include all labour, carpentry, making chases, grooves, polish and provision of 6nos. M.S.holdfast 25x4x230mm per frame with nuts and bolts asrequired and grouted in situ in concrete blocks of mix 1:2:4 and of size as directed. For concrete surfaces, 12mm diameter counter sunk anchor bolts orcoarch screws shall be used for fixing of all door frames, finishing the frames with putty and two coats of approved matching polish/enamel paint. Innersurface of teak wood frame shall be coated with anti-termite solution etc. all complete.


11000038-HD-11370



128 AL. GLZ. DOOR-12MM TOUGH.GLASS Square Metres 4512.00

129 PDR.COAT.AL GLZ. DOOR-12mm… Square Metres 3192.00

130 PDR.COAT.AL GLZ. DOOR-TOUGH…. Square Metres 4587.00

131 ANOD. AL.FIXED GLZ.-12MM GLASS Square Metres 3004.00

132 AL. GLZ.FIXED-12MM TOUGH.GLASS Square Metres 4512.00

133 PDR.COAT.AL GLZ. FIX.GLZ.-12MM Square Metres 3192.00

134 PDR.COAT.AL GLZ. FIXED-TOUGH.. Square Metres 4587.00

135 HYDRAULIC FLOOR SPRINGS Each 1604.00

ALUMINIUM GLAZED DOOR WITH 12MM GLASS: Providing and fixing Aluminium glazed door with 15 micron coloured anodised aluminium sectionwith extruded built up section of approved make and weight ratio joints mitred joint with heavy duty aluminium pressure die cast cleats with fins to match thesection of frames conforming to approved section and shutter conforming to approved section and glazed with12 mm thick glass fixed to shutter with neoprin /PVC gasket/ CP brass / Stainless steel screws or with fixing clips or with expansion hold fasteners with requisite PVC / Neoprin felt /

polysulphide sealant / silicon sealant etc complete as per architectural drawing and instruction of Engg.-In-Charge. Al anodised shop front doors with framesat top and bottom (without any vertical aluminium section) of HINDALCO make - section no.

SP-2670 of size 88x42x2.3 with weight of 2.927 kg/m for door top and bottom, round acrylic handle using CP brass / Stainless steel screws. The glassshould be single piece only. All glass edges shall be grinded and polished smooth as per instructions. The floor spring strut shall be fixed and accommodatedin Aluminium section groove. In case of non-availability, approved equivalent make for Al sections is JINDAL. Approval of Engg.-In-Charge shall be takenbefore using equivalent sections matching next higher dimensions and weight per running metre without extra cost. Approved Make of Glass: AIS, Modi, SaintGobain, Triveni

With 12 mm toughened glass with all specification as item no.127

With Powder Coated aluminum section of approved colour having coating thickness of minimum 50 micron with 12mm plain glass and all specification as itemno. 127 Anodisation shall not be done.

With Powder Coated aluminum section of approved colour having coating thickness of minimum 50 micron with 12mm toughened glass and all specificationitem no. 127. Anodisation shall not be done.

ALUMINIUM FIXED GLAZING WITH 12MM GLASS: Providing and fixing Aluminium fixed glazing with 15 micron coloured anodised aluminium sectionminimum wall thickness of not less than 2 mm with extruded built up section of approved make and weight ratio joints mitred joint with heavy duty aluminiumpressure die cast cleats with fins to match the section of frames conforming to approved section and glazed with 12 mm thick glass fixed with Al snap beadingand neoprin / PVC gasket / CP brass / Stainless steel screw and fixed to the wall with rawl plugs and screws or with fixing clips or with expansion holdfasteners including necessary filling up of gaps at junctions, at top, bottom and sides with requisite PVC / Neoprin felt / polysulphide

sealant / silicon sealant etc complete as per architectural drawing and instructions of Engg.-In-Charge.

Al anodised shop front fixed glazing with frames at top and bottom of HINDALCO make section no. SP-2670 of size 88x42x2.3 with weight of 2.927 kg/m orapproved equivalent and at two side ends of HINDALCO make section no. SP-730 of size 63.5x38x3 with weight of 1.55 kg/m or approved equivalent andfixing cleats/clips of HINDALCO make section no. SP-1778 of size 17.15x17.27x1.4 with weight 0.175 kg/m without any intermediate vertical aluminiumsections at joints. The intermediate vertical joints spacing in glass shall not be less than 3 m c/c and no horizontal joints shall be permitted in glass. Thevertical joints shall be finished smooth having machine cut glass edges in true plumb, line and level. The joint shall be treated with silicon sealant to stop wateringress and glass surfaces shall be cleaned neat of left over sealant. Prior approval of HPCL Engg.-In-Charge shall be obtained if spacing of vertical joints isneeded to be less than 3 m c/c. Approved Make of Glass: AIS, Modi, Saint Gobain, Triveni. In case of non-availability, approved equivalent make for Alsections is JINDAL.

Approval of Engg.-In-Charge shall be taken before using equivalent sections matching next higher dimensions and weight per running metre without extracost.

With 12 mm toughened glass with all specification as item no.131

With Powder Coated Al section with 12mm plain glass and all specification as item no.131. Anodisation shall not be done.

With Powder Coated Al section with 12mm toughened glass and all specification as item no.131. Anodisation shall not be done.


11000038-HD-11370



136 ALUM. PANEL.DOOR-PART. BOARD Square Metres 3234.00

137 ALUM. PANEL.DOOR-BISON LAM Square Metres 2600.00

138 ALUMINIUM WINDOWS (OPENABLE) Square Metres 2788.00

139 ALUM. WINDOWS SLIDING- 2 TRACK Square Metres 3199.00

140 ALUM. WINDOWS SLIDING- 3 TRACK Square Metres 3199.00

141 ALUMINIUM LOUVERED VENTILATOR Square Metres 3538.00

HYDRAULIC FLOOR SPRINGS Providing and fixing double action hydraulic floor springs of approved brand ( HARDWYN / EVERITE/ SANDHU)conforming to IS 6315 : 1992 for aluminium doors. Rate to include cutting of floors as required, embedding in floors and cover plates etc complete as perspecifications. Load Capacity = 61-80 kg

ALUMINIUM PANELED DOOR : Providing and fixing 15 micron colored anodised single leaf aluminium door with minimum wall thickness of not less than 2mm , joints mitred and jointed with heavy duty aluminium pressure die cast cleats with fins to match the outer frames and door frames conforming JINDALsections as specified fully paneled with 9 mm thick pre-laminated 3 layers medium density ( exterior grade) particle board Grade-1, type -II conforming toIS:12823 bonded with phenolformaldehyde synthetic resin of approved brand and manufacturer fixed to shutter with aluminium snap beading and neoprene /PVC gasket / CP Brass /stainless steel screws fixed to the wall with requisite

rawl plugs and screw or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top , bottom and sides withrequisite PVC/neoprene felt/polysulphide sealant/silicon sealant including hard ware such as tower bolt of 150 mm length from inside and Aluminum handleand Aluminum aldrop of 200 mm length

on both sides, 3 nos. Aluminium hinges of 100 mm length etc all complete as per architectural drawing. Aluminium door section of JINDAL make or equivalent make with the following section : Main frame on all sides - 4700 -101.6 x 44.45 x 2.5 of weight 1.977 kg/m Shutter vertical frame- 4537 - 53.7x44.45x2.3 ofweight 1.238 kg/m. Shutter top frame - 4540 - 53.7x44.45x2.3 of weight 1.173 kg/m.

Shutter middle frame - 4621 - 49.91x44.45x3 of weight 1.495 kg/m Shutter bottom frame - 4524 -83.5x44.45x3 of weight 2.107 kg/m, aluminium Cast Doorhandle and Clip - 4420 - 19x17.3x0.9 of weight 0.124 kg/m. In case of non-availability, approved equivalent make for Al sections is HINDALCO. Approval ofEngg.-In-Charge shall be taken before using equivalent sections matching next higher dimensions and weight per running metre without extra cost.

Providing and fixing aluminium door to concrete and brick work using 9 mm thick Pre laminated both side Bison lam sheet ( Cement particle Board) instead ofparticle board fixed to shutter. Rest of the specifications same as item no. 136 as applicable.

ALUMINIUM WINDOWS (OPENABLE) : Providing and fixing 15 micron colour anodised aluminium glazed windows with 5 mm glass & extruded built upsection of wall thickness not less than 1.4 mm and approved make with glass panel fixed to side -hung shutter with aluminium snap beading and neoprene /PVC gasket / CP Brass /stainless steel screws fixed to the wall with requisite rawl plugs and screw or with fixing clips or with expansion hold fastenersincluding necessary filling up of gaps at junctions at top , bottom and sides with requisite PVC / neoprene felt / polysulphide sealant/silicon sealant includingheavy duty handle cum locking arrangement etc all complete as per architectural drawing and the direction of Engg.In-charge.

Aluminium door section of JINDAL make or equivalent make with the following sections : Outer frame - 8804 of weight 0.622 Kg/m Shutter frame- 8802 ofweight 0.575 kg/m; Mullion - 8803 of weight 0.729 kg/m; Cleat angle (HIDALCO make) A-3350 - 38x25x3 of weight 0.490 kg/m; Glazing clip - 4433 of weight0.137 kg/m. Approved Make of Glass : AIS, Modi, Saint Gobain, Triveni. In case of non-availability, approved equivalent make for Al sections is HINDALCO.Approval of Engg.-In-Charge shall be taken before using equivalent sections matching next higher dimensions and weight per running metre without extracost.

Same as above item no.138 but Aluminium sliding windows of Jindal make shutter sections: Top & Bottom - 8820- 1.5 mm thick @ 0.547 kg/m; HandleSection 8822- 1.5 mm thick @ 0.547 kg/m; Shutter Interlock 8821- 1.45 mm thick @ 0.607 kg/m. Rate includes wheels/bearings, interlocking arrangementsetc. complete. The track section shall be as follows: Two Track Window: Top & Side - 8931-1.5 mm thick @ 0.784 kg/m; Bottom (Bulb) - 8932- 1.5 mm thick @ 0.909 kg/m

Same as Item No.138 but Three Track Window: Top & Side - 8933-1.5 mm thick @ 1.06 kg/m; Bottom (Bulb) - 8934- 1.5 mm thick @ 1.248 kg/m

ALUMINIUM LOUVERED VENTILATOR : Providing and fixing 15 micron colour anodised aluminium ventilator with extruded built up section of wallthickness not less than 1.5 mm and approved make glazed with 5 mm thick opaque glass louver 100mm wide.


11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATE142 ALUM. DOOR/FIXD. GLZ. 6 MM GLASS Square

Metres 2421.00

143 STEEL WINDOWS Square Metres 2260.00

144 STEEL DOORS Square Metres 1775.00

145 ROLLING SHUTTER Square Metres 1775.00

146 GRILL IN ROLLING SHUTTER Square Metres 1900.00

147 DISPLAY SHELF Square Metres 3296.00

ALUMINIUM DOOR/FIXED GLAZING WITH 6 MM GLASS : Providing and fixing 15 micron coloured anodised aluminium fixed glazing/aluminium door with6 mm glass extruded built up section of wall thickness not less than 1.5 mm and approve make with glass panel fixed with Aluminium snap beading/Neoprene / PVC gasket/CP Brass /stainless steel screws and fixed to the wall with requisite rawl plugs and screw or with fixing clips or with expansion holdfasteners including necessary filling up of gaps at junctions, at top , bottom and sides with requisite PVC / neoprene felt/ polysulphide sealant/silicon sealantall complete as per architectural drawing and the direction of Engg. In-charge.

Aluminium section of JINDAL make or equivalent make with the following sections :

Fixed Glazing:Outer frame sections - 4688- 63.5x38.1x1.65 of weight 0.942 kg/m.

Intermediate frame - 4687- 63.5x38.1x1.53 of weight 0.942 kg/m.Glass panels used shall not be less than 2.4 m (height) x 1.2 m (width). All the joints shall be provided with Aluminium sections as specified.

Door:

Outer side frame - 4550 - 47.62x44.45x1.52 of weight 0.881 kg/m.

Bottom frame - 4553 - 95.25x44.45x1.70 of weight 1.301 kg/m

Intermediate frame - 4621- 49.91x44.45x1.60 of weight 0.882 kg/m.

Clip- 4420- 19x17.3x0.9 of wt. 0.124 Kg/m.The floor spring strut shall be fixed and accommodated in Aluminium section groove. The door shall be provided with die cast aluminium handle, towerbolt,locking arrangement etc. complete. The joints and gaps shall be treated with silicon sealant to stop water ingress and glass surfaces shall be cleaned neat ofleft over sealant. Approved Make of Glass: AIS, Modi, Saint Gobain, Triveni. In case of non-availability, approved equivalent make for Al sections is JINDAL.Approval of Engg.-In-Charge shall be taken before using equivalents matching next higher dimensions and weight per running metre without extra cost.

STEEL WINDOWS : Supply, fabrication and fixing of MS glazed windows using approved Z sections with 5mm plain glass including providing grill with12mm square bar @100mm c/c , painting with two coats of red oxide primer and two coats of synthetic enamel paint, handle , stay arrangement etc. complete.

STEEL DOORS : Supply, fabrication and fixing of MS Door using 35x35x5 angle frame and 25x25x3 angle members including bracings with 16 gauge MSsheet stitch welded to Door shutter frame complete as per direction of Engg.-In-Charge painting with two coats of red oxide primer and two coats of syntheticenamel paint, handle , stay arrangement ,tower bolt etc. complete.

ROLLING SHUTTER Supply, fabrication and fixing of MS rolling shutter of the following specifications including grill window of 300 mm height at eye level forvisibility even in closed position. Code: Conforming to IS 6248 – 1979 Type: Self Coiling type (manual) Curtains: Interlocking cold rolled lath section of 0.8mm thickness. Lock plate : MS sheet of 3.15 mm thick reinforced with MS angles of 35 x 35 mm. Guide channel : MS sheets of 3.5 mm thick Bracket Plate :MS Sheet of 0.9 mm thick.

Hood Covers : MS sheet of 0.9 mm thick Locking handle : To be provided suitably. Rate shall include providing and fixing holdfasts and painting two coats ofenamel paint of approved make and shade over two coats of zinc phosphate primer. Shutter up to 10 SQM -push pull type hand operated with ball bearings ,For 10 SQM upto 30 SQM- Mechanical operated gear type with ball bearing, a pulling hook shall be provided for each of the rolling shutter.

GRILL IN ROLLING SHUTTER : Supply, fabrication and fixing of manually operated steel rolling net shutter as per the specification. Nets to be in hexagonalpattern, The round MS bars used for jali should be 8mm in dia . All other specification as item no. 145.


11000038-HD-11370



148 DISPLAY SHELF - BOTTOM STORAGE Square Metres 4285.00

149 FAN HOOKS Each 50.00

150 MORTICE LOCK Each 870.00

151 DOOR CLOSER Each 1000.00

152 STRUCT.STEEL WORK-SERVICE BAY Metric Ton 57000.00

153 S/I/F COR. ASBESTOS SHEET-ROOF Square Metres 345.00

154 S/I/F COR.ASBESTOS SHEET-GABLE Square Metres 400.00

155 20 gauge (1.0MM) sheets Square metres 310.00

156 22 gauge (0.8M) sheets Square metres 290.00

157 GYPSUM BOARD FALSE CEILING Square Metres 600.00

DISPLAY SHELF: Providing & fixing in position 12 mm thick plain glass of Modi/AIS/Saint Gobain/Triveni make with polished edges in the grooves betweenthe 25 mm thick exterior grade MDF board planks at 325 mm c/c & 350 mm wide. The MDF board shall be fixed on teak wood frame fixed to the wall usingplugs, screws and holdtights. Cross section of teak wood shall be 50x75 mm. The teak wood shall be seasoned and brushed with anti-termite chemical beforeuse. Teak wood framing shall be fixed over wall in such a way that it forms grids of size 450x325 mm so as not to obstruct the grooves. The exposed surfaceof the MDF board shall be finished with 1.5 mm thick lamination of approved colour & combination of colours with teak wood beadings on edges. Theapproved brand for the lamination shall be Formica/Greenlam / Sundek.

Specifications as item no. 147 but with storage at bottom, as per enclosed drawing.

FAN HOOKS : Providing & fixing MS fan hooks with 16 mm dia MS bar bent to shape with hooked ends in RCC Slab during laying including painting theexposed portion.

MORTICE LOCK Providing & fixing GODREJ make only six lever lock ( Cylindrical/ Round Head ) including all necessary hardware etc.

DOOR CLOSER Providing and fixing door closer of Hardwyn / Everite make size no. 2.

Supplying , erecting and fixing in position Pre- fabricated structures at all elevations for service bay using structural steel sections conforming to IS:2062 ,including cutting, welding or bolting, supply of bolts/nuts/washers etc., complete as per drawings including surface preparation and applying one coat of ZincPhosphate Primer before erection and two coats of synthetic enamel paint as per specification after erection and all materials and labour complete. ( Nowelding is permitted at site).

The rate quoted shall include cost of bolts, nuts, washers, welding and electrodes and any other consumables required for completing the work. The bolts ,nuts , washers, welds etc shall not be separately measured and paid for.

Supply , erection and fixing of corrugated asbestos cement sheet of Everest make or approved equivalent for service bay including supply and fixing ofbitumen/GI washer, J bolt etc. For Roof

Same as Item No.153 but for side sheet including gable end.

GI SHEET ROOFING : Supplying and fixing corrugated GI sheet roofing of approved make and following thicknesses with GI 'J' or 'L' hooks 10mm dia; GIlimpet and bitumen washer complete. Rate to exclude purlins, rafters, trusses etc, which shall paid under separate head.

Same as item No: 155 but for 22 gauge

Providing and fixing Gyp board false ceiling with required accessories INDIA GYPSUM make including painting with two coats of plastic emulsion paint.12.5 mm thick 'Gypboard' shall be screw-fixed to the underside of suspended GI grid. GI grid shall be installed as per manufacturer's specifications. GI gridshall consist of ceiling sections (India Gypsum Code no. MF5) at maximum c/c distance 450 mm, Perimeter channel (India Gypsum code no. MF6A),intermediate channels (India Gypsum code no. MF7) at maximum c/c distance 1200 mm.

The ceiling sections should be fixed to intermediate channels with connecting clips (India Gypsum code no. ME9). GI grid shall be fixed to RCC slab abovewith the help of 25x0.5 mm strap hanger (India Gypsum code no. MF 8) and soffit cleat (India Gypsum code no. P534). The joints between soffit cleat andstrap hanger and GI grid & strap hanger shall be with 6.4x12.7 mm nut and bolt (India Gypsum code no. P526). Soffit cleat shall be fixed to RCC ceiling withW.E. type 12 mm dia, 17/16" long steel rawl plug. Maximum c/c distance (both ways) of strap hangers shall be 1200 m. The Gypboard shall be fixed fixed toGI grid with 25 mm long Drawall screws. The Gypboard to be used shall be 12.5 mm thick tapered edge boards. The boards shall be taped & filled fromunderside to ceiling.


11000038-HD-11370



158 ACOUSTIC. SUSP. CEILING BUTT.. Square Metres 625.00

159 ACOUSTIC. SUSP. CEILING TEGULR Square Metres 660.00

160 WATER CLOSET-EUROPN.,COLOURED Each 7800.00

161 WATER CLOSET-EUROPEAN WHITE Each 5300.00

162 WATER CLOSETS-INDIAN,COLOURED Each 3250.00

The rate shall be inclusive of additional ceiling sections and intermediate channels shall be provided at openings for light fixtures, AC ducts, vertical drops,offsets etc Additional intermediate channels shall be fixed to strap hangers at every 1200 mm for additional support to prevent strap hangers frombuckling/swaying. Item to be completed in all respect including necessary sleeves for ducts , finishing of joint cut outs, supports for AC grills, light fixtures,speakers etc. complete as per directions of Engg.-In-Charge.

Providing & Fixing of Armstrong Acoustical Suspended Ceiling System with Fissured Tiles having Tegular edges . The tiles should have Humidity Resistance of 90% RH, Average NRC .50, Light Reflectance >80%, Thermal Conductivity k = 0.052 – 0.057 w/m°c, Colour White , Fire Performance Class 0/Class 1 (BS - 476) in module size of 600mm x 600mm x 15mm laid on 24XL - Hot Dipped Galvanised steel suspension System having rotary stitching on the Main Runner, 1200 mm & 600 mm Cross Tees. INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the structural socket by approved hanger at 1200mm maximum centre. The last hanger at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees.Perimeter trim to be Armstrong wall angles or channel, secured to walls at 450 mm max. C/cFor fissured RH 90 Butt Edge.

Providing & Fixing of Armstrong Acoustical Suspended Ceiling System with Fissured Tiles having Tegular edges . The tiles should have Humidity Resistance of 90% RH, Average NRC .50, Light Reflectance >80%, Thermal Conductivity k = 0.052 – 0.057 w/m°c, Colour White , Fire Performance Class 0/Class 1 (BS - 476) in module size of 600mm x 600mm x 15mm laid on 24XL - Hot Dipped Galvanised steel suspension System having rotary stitching on the Main Runner, 1200 mm & 600 mm Cross Tees. INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the structural socket by approved hanger at 1200mm maximum centre. The last hanger at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees.Perimeter trim to be Armstrong wall angles or channel, secured to walls at 450 mm max. C/cFor fissured RH 90 Tegular Edge.

EUROPEAN TYPE Supplying and fixing approved colour (pastel colour) wall mounted vitreous china European type water closet comprising of the followingaccessories including cutting and making good the walls & floors wherever required complete as directed by Engg.-In-Charge, having following (A) Coloured (pastel colour) vitreous china European water closet with P or S trap of Parryware make Cascade series No. 0219 having integral matching colour vitreouschina cistern supplied as part of the closet with all mechanisms, with necessary fittings, brackets, screws, etc all complete as per the direction of Engg.-In-Charge.

(B) 15mm NB CP brass angle valve of approved brand as per the direction of Engg.-In-Charge (C) 15 mm NB CP brss inlet connection with Brass unions atthe ends. (D) Parryware/Commander make or equivalent matching colour polypropylene seat cover with necessary brass hinges and rubber bushes etc (E)WC connector with neoprene rubber etc. Approved Equivalent - Hindware 20028 with matching colour Vitreous China cistern with all mechanisms, fittings etc.complete.

EUROPEAN TYPE Supplying and fixing white wall mounted vitreous china European type water closet comprising of the following accessories includingcutting and making good the walls & floors wherever required complete as directed by Engg.-In-Charge, having following (A) White vitreous china Europeanwater closet with P or S trap of Parryware make Cascade series No. 0219 having integral matching colour vitreous china cistern supplied as part of the closetwith all mechanisms, with necessary fittings, brackets, screws, etc all complete as per the direction of Engg.-In-Charge.

(B) 15mm NB CP brass angle valve of approved brand as per the direction of Engg.-In-Charge (C) 15 mm NB CP brss inlet connection with Brass unions atthe ends. (D) Parryware/Commander make or equivalent matching colour polypropylene seat cover with necessary brass hinges and rubber bushes etc (E)WC connector with neoprene rubber etc. Approved Equivalent - Hindware 20028 with matching colour Vitreous China cistern with all mechanisms, fittings etc.complete.

INDIAN WATER CLOSET Supplying and fixing approved colour (pastel colour) vitreous china Orissa Pan type water closet comprising of the followingaccessories including cutting and making good the walls & floors wherever required complete as directed by Engg.-In-Charge ( A) Coloured (pastel colour)vitreous china 580 mm size water closet of Parryware Cat. 0109/17 with P or S trap (B) 10 litre capacity hi-grade engineering plastic low level flushing cisternof matching colour Cat. - 0709 of Parryware with necessary fittings, brackets , screws etc. all complete.


11000038-HD-11370



163 WATER CLOSETS-INDIAN, WHITE Each 2400.00

164 URINALS - COLOURED Each 1650.00

165 URINAL-NEW MAGNUM WHITE Each 2400.00

166 URINAL-NEW MAGNUM COLOURED Each 3100.00

167 URINAL-PARRYWARE WITH IN BUILT SENSOR Each 14000.00

168 URINAL SENSOR-SENSOTRONIC Each 8500.00

169 SENSOR FAUCET-WASH BASIN Each 14000.00

170 SENSOR FAUCET-URINAL Each 14000.00

171 URINAL DIVISION PLATE Each 1450.00

172 HAND WASH BASIN W/O PEDESTAL Each 2250.00

173 HAND WASH BASIN WITH PEDESTAL Each 2750.00

(C) 32 mm CP brass flush pipe of approved length with necessary fittings, clamps etc. (D) 15 mm NB CP inlet connections with brass union at the ends. (E)15mm NB CP brass angle valve of approved brand as per the direction of Engg.-In-Charge (F) WC connector with neoprene rubber. Approved Equiv. -Hindware Cat. 20004 with equivalent low level cistern

INDIAN WATER CLOSET Supplying and fixing white vitreous china Orissa Pan type water closet comprising of the following accessories including cuttingand making good the walls & floors wherever required complete as directed by Engg.-In-Charge ( A) White vitreous china 580 mm size water closet ofParryware Cat. 0109/17 with P or S trap (B) 10 litre capacity hi-grade engineering plastic low level flushing cistern of matching colour Cat. - 0709 of Parrywarewith necessary fittings, brackets , screws etc. all complete.

(C) 32 mm CP brass flush pipe of approved length with necessary fittings, clamps etc. (D) 15 mm NB CP inlet connections with brass union at the ends. (E)15mm NB CP brass angle valve of approved brand as per the direction of Engg.-In-Charge (F) WC connector with neoprene rubber. Approved Equiv. -Hindware Cat. 20004 with equivalent low level cistern

Supplying and fixing coloured (pastel colours) vitreous china flat back urinal of size 300mmx400mm with integrated overflow of Hindustan Sanitary orequivalent approved make with CP flush valve, CP pipe connection, CP waste coupling , CP Brass bottle trap, 32 mm PVC waste line of required lengthetc. all complete as per the direction of Engg.-In-Charge.

Supplying and fixing WHITE vitreous china urinal of Parryware make New Magnum Series No. 0575, CP flush valve, CP pipe connection, CP waste coupling, CP Brass bottle trap, 32 mm PVC waste line of required length etc. all complete as per the direction of Engg.-In-Charge. Approved Equivalent - Hindware60006 Olympous half stall

Supplying and fixing PASTEL COLOURED vitreous china urinal of Parryware make New Magnum Series No. 0575, CP flush valve, CP pipe connection, CPwaste coupling , CP Brass bottle trap, 32 mm PVC waste line of required length etc. all complete as per the direction of Engg.-In-Charge. ApprovedEquivalent - Hindware 60006 Olympous half stall

Supplying and fixing PASTEL COLOURED vitreous china urinal of Parryware make Series No. C8098, CP flush valve, CP pipe connection, CP wastecoupling , CP Brass bottle trap, 32 mm PVC waste line of required length etc. all complete with in built sensor for water discharge and flushing. Rate includemaking all connections/electrical connections etc complete job.

Supply, installation and commissioning all complete Jaquar make Sensotronic Concealed type Flushing system (Model 51087 - Chrome) including allaccessories, all connections, electricals etc. all complete as per the direction of Engg.-In-Charge.

Supply, installation and commissioning all complete SENSOR FAUCET FOR WASH BASIN WITH 190MM LONG SPOUT (WALL Mounted Model SNR-51071 Chrome, Make - Jaquar) complete with MS installation Box with 2 Nos control Cocks, all accessories, connections etc all inclusive.

Supply, installation and commissioning all complete SENSOR FAUCET FOR URINALS (Model SNR-51077 Chrome, Make - Jaquar) concealed typeFlushing Valve complete set with Installation Box & Control Cock , all accessories, connections etc. all inclusive.

Providing and fixing 1200 x 450 x 18 mm (minimum) size machine cut and polished black/approved colour granite partition plate between urinals includingcutting masonry / concrete surface to required size, fixing the division plate on the ceramic tiles by means of SS clamps, nuts & bolts, polishing all exposedsurface etc all complete as directed by Engg.-In-Charge.

HAND WASH BASIN : Providing and fixing coloured (pastel colours) wash basins of size 550 x 400 without pedestal, including the following accessories:(a)15mm brass CP Jaquar make (Cat.no.093) stop cock -1 No . (b) 15mm CP connections from the above stop cock to pillar cock - 1 No. (c) 32mm dia wastecoupling, CP brass chain and rubber stopper. (d)30mm bottle trap Jaquar make with cleaning eye, extension piece and wall flange.

(d) Providing and fixing brass CP Jaquar make 13mm half turn pillar cock. (Cat. no.011) Rate to include supply, painting and fixing of necessary CI bracketswith nuts and bolts and fixing the wash basin with all necessary connections in walls.

Hand Wash basin with matching color pedestal. Rest specifications as item no. 172


11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATE174 OVAL BELOW COUNTERBASIN-WHITE Each 1200.00

175 OVAL BELOW COUNTERBASIN-COLOUR Each 1550.00

176 WALL HUNG BASIN & PEDESTAL Each 1575.00

177 MIRROR - 5.5 MM THICK Square Metres 1800.00

178 MIRROR- 600X600X5.5 MM Each 650.00

179 SOAP TRAY Each 130.00

180 LIQUID SOAP DISPENSER Each 650.00

181 TOILET PAPER HOLDER Each 135.00

182 TOWEL RAIL Each 250.00

183 TOWEL RING:CAN-1121, JAQUAR Each 650.00

184 TOWEL RING:1576, PARKO Each 575.00

185 AUTOMATIC HAND DRYER Each 6500.00

186 AUTOMATIC AEROSOL DISPENSER Each 2750.00

187 AUTOMATIC SHOE SHINING MACHINE Each 12100.00

Supplying and fixing ceramic WHITE COLOUR OVAL BELOW COUNTER BASIN of Parryware size 550x450 mm make No. 550 0418, CP flush valve, CPpipe connection, CP waste coupling , CP Brass bottle trap, 32 mm PVC waste line of required length etc. all complete as per the direction of Engg.-In-Charge. Approved Equivalent - Hindware 10016 Oval

Supplying and fixing ceramic PASTEL COLOUR OVAL BELOW COUNTER BASIN of Parryware size 550x450 mm make No. 550 0418, CP flush valve, CPpipe connection, CP waste coupling , CP Brass bottle trap, 32 mm PVC waste line of required length etc. all complete as per the direction of Engg.-In-Charge. Approved Equivalent - Hindware 10016 Oval

Supplying and fixing ceramic approved colour Parryware make 580x455 mm size No. CTH-0481 wall hung wash basin with matching coulour ceramicpedestal no. 0375, CP flush valve, CP pipe connection, CP waste coupling , CP Brass bottle trap, 32 mm PVC waste line of required length etc. allcomplete as per the direction of Engg.-In-Charge. The fixing shall be done by Parryware bolts only and the pedestal shall be screwed to floor as permanufacturer's specifications. Approved Equivalent - Hindware wash basin Viking 10008, Pedestal 11003

Providing and fixing beveled edge mirror of superior glass of 5.5 mm thick & 600 x 600 mm size of BELGIUM GLASS or any other equivalent make, craftpaper, 3mm thick felt backing or 6 mm asbestos sheet. Teak Wood beads 25x40 mm as per approved shape/drawing allround and fixed with wooden plugswith CP brass screws and cup washers etc all complete as directed by Engg.-In-Charge.

Same as item no. 177 but of size 600 x 600 mm.

Providing and fixing readymade CP brass soap tray near wash basin with CP brass screws of approved make.

Providing and fixing soap dispenser having refillable container system and transparent view of container showing remaining soap level. Care shall be taken sothat tiling is not damaged while installation. Make - Technocrats/ Euronics /Askon

Supplying and fixing of 150 x 150 mm pastel coloured toilet paper holder of Hindustan Sanitary ware or equivalent approved make at required position andelevation as directed. Rate to include making good the chases in walls after fixing the above.

Providing and fixing CP brass towel rail of 20 mm dia and 600 mm long including all accessories such as brackets (coloured), fixing and anchoring etc.complete as directed.

Providing and fixing CP brass Towel Ring. Make-Jaquar, Continental Range CAN-1121 including all accessories such as brackets, fixing and anchoring etc.complete as directed.

Providing and fixing CP brass Towel Ring. Make-Parko, Classic Line Collection, No.1576 including all accessories such as brackets, fixing and anchoring etc.complete as directed.

Providing, fixing and commissioning fully automatic hand dryer i.e. autostart on positioning the hand and autostop. Care shall be taken so that tiling is notdamaged while installation. Rate includes PVC insulated power chord having copper conductor and Anchor ROMA make 3 pin power plug matching ampereload of instrument. Make - Technocrats (Model Alpha AP-800) or Euronics (Model CYC 30)

Providing, fixing and commissioning fully automatic aerosol dispenser (Auto Freshener). The price includes spray fragrance cam with approved aroma etc.complete. Rate includes PVC insulated power chord having copper conductor and Anchor ROMA make 3 pin power plug matching ampere load of instrument.Care shall be taken so that tiling is not damaged while installation. Make - Technocrats (Model Deluxe)


11000038-HD-11370



188 HYGI SPRAY Each 540.00

189 STOP COCK CONCEALED-PARKO 1516 Each 510.00

190 SWAN NECK TAP-PARKO 1536 Each 775.00

191 PILLAR COCK-PARKO 1501 Each 400.00

192 BIB COCK LONG BODY-PARKO 1511 Each 510.00

193 BIB COCK LONG NOSE-PARKO 1506A Each 590.00

194 BIB COCK -PARKO 1506 Each 400.00

195 PILLAR COCK-JAQUAR 23011 Each 515.00

196 PILLAR COCK-JAQUAR 23021 Each 665.00

197 BIB COCK-JAQUAR 23037 Each 500.00

198 BIB COCK-JAQUAR 23039 Each 535.00

199 BIBCOCK LONG BODY-JAQUAR 23107 Each 685.00

200 BIB COCK-2 WAY-JAQUAR 23041 Each 750.00

201 ANGULAR STOP COCK-JAQUAR 23053 Each 490.00

202 ANGULAR STOP COCK-JAQUAR 23055 Each525.00

203 CONCEAL. STOPCOCK-JAQUAR 23069 Each 665.00

Providing, fixing and commissioning fully automatic shoe polish machine with electronic eye (infra red sensor) having both separate black and brown rollers.The machine shall start automatically when shoe is placed and automatically stop. Rate includes PVC insulated power chord having copper conductor andAnchor ROMA make 3 pin power plug matching ampere load of instrument. Care shall be taken so that finishing is not damaged while installation. Make -Technocrats (Model Executive Deluxe)

Providing and fixing in position CP brass Hygi Spray of Parryware make Model T9929G1 inclusive of all fixtures, fittings and fasteners making operationalcomplete. Approved Equivalent Make - Hindware

Providing and fixing in position CP brass stop cock Parko make classic line series No. 1516 including all necessary fixtures etc. complete.

Providing and fixing in position CP brass swan neck tap Parko make classic line series No. 1536 on wash basins including all necessary fixtures etc.complete.

Providing and fixing in position CP pillar cock of Parko make classic line series No. 1501 including all necessary fixtures etc. complete.

Providing and fixing in position CP long body bib cock of Parko make classic line series No. 1511 including all necessary fixtures etc. complete.

Providing and fixing in position CP long nose bib cock of Parko make classic line series No. 1506 A including all necessary fixtures etc. complete.

Providing and fixing in position CP bib cock of Parko make classic line series No. 1506 including all necessary fixtures etc. complete.

Providing and fixing in position CP brass pillar cock with Aerator of Jaquar Clarion Range No. 23011. Rate to include all related civil repairs, fitments, joineriesetc. complete.

Providing and fixing in position CP brass long neck pillar cock with Aerator of Jaquar Clarion Range No. 23021. Rate to include all related civil repairs,fitments, joineries etc. complete.

Providing and fixing in position CP brass bib cock of Jaquar Clarion Range No. 23037. Rate to include all related civil repairs, fitments, joineries etc.complete.

Providing and fixing in position CP brass bib cock with long thread of Jaquar Clarion Range No. 23039. Rate to include all related civil repairs, fitments,joineries etc. complete.

Providing and fixing in position CP brass long body bib cock with wall flange of Jaquar Clarion Range No. 23107. Rate to include all related civil repairs,fitments, joineries etc. complete.

Providing and fixing in position CP brass bib cock of Jaquar make Clarion Range No.23041. Approved equivalent Parko make.

Providing and fixing in position CP brass angular stop cock (regulating valve) of Jaquar Clarion Range No. 23053. Rate to include all related civil repairs,fitments, joineries etc. complete.

Providing and fixing in position CP brass long thread angular stop cock (regulating valve) of Jaquar Clarion Range No. 23055. Rate to include all related civilrepairs, fitments, joineries etc. complete.


11000038-HD-11370



204 CONCEAL. STOPCOCK-JAQUAR 23083 Each 800.00

205 STOPCOCK MALE END-JAQUAR 23093 Each 490.00

206 STOPCOCK FEMALE-JAQUAR 23097 Each 490.00

207 CONCEALED GI PIPING - 15 NB Running Metre 145.00



210 EXPOSED GI PIPING - 15 NB Running Metre 115.00



213 BRASS GATE VALVE - 15 NB Each 260.00



216 HDPE SINTEX WATER TANK-1000 L Each 7094.00

217 HDPE SINTEX WATER TANK-500 L Each 5483.00Same as item no.216 but of 500 L capacity.

218 PVC PIPE - 110 MM, 4KG/SQCM Running Metre 255.00

219 PVC PIPE - 80 MM, 4KG/SQCM Running Metre 215.00

Providing and fixing in position CP brass concealed stop cock (reduced body) of Jaquar Clarion Range No. 23069. Rate to include all related civil repairs,fitments, joineries etc. complete.

Providing and fixing in position CP brass Extra Heavy Body concealed stop cock with adjustable wall flange of Jaquar Clarion Range No. 23083. Rate toinclude all related civil repairs, fitments, joineries etc. complete.

Providing and fixing in position CP brass male end stopcock of Jaquar Clarion Range No. 23093. Rate to include all related civil repairs, fitments, joineriesetc. complete.

Providing and fixing in position CP brass female end stopcock of Jaquar Clarion Range No. 23097. Rate to include all related civil repairs, fitments, joineriesetc. complete.

CONCEALED GI PIPING Providing & fixing 15 mm medium grade GI pipes of TATA / JINDAL / ZENITH / SURYA / TIRUPATI / RAMA make conforming toIS-1239 concealed in the walls and under the concrete floors including making chases in the walls or concrete floors, fixing with clamps at every 1m c-c,necessary tees, bends, elbows, plugs, nipples, unions, testing of pipelines for leaks upto a pressure of 6 Kg/sq cm , painting the pipes with hot bitumen,wrapping the pipes with Hessian cloth and making chases of the walls good after piping.

Same as item no.207 but size 20 mm.


EXPOSED GI PIPING Description same as above item no. 207 but providing, laying and fixing 15 MM medium grade pipes in open on brick or RCC surfacewith the help of GI 'U' clamps at every 1 m and at every turn.



Providing & fixing 15 mm brass full way gate valve ISI marked & of Leader / GG make.



WATER TANK Supplying and installation of HDPE water tanks Sintex make of 1000 litre capacity including 300 mm high brick masonry pedestal of 230mmthick in CM 1:5, providing 75mm thick RCC 1:2:4 slab with reinforcement 8mm tor @150mm c/c, lifting the tank , making all necessary GI connections toinlet, outlet, and overflow nozzles and cleaning the tank before commissioning.

PVC SOIL / WASTE /RAIN WATER PIPES Supplying and laying 110 mm PVC pipe of 4KG/sqcm pressure rating including plain or door type bends,shoes, offsets, clamps junctions, tees, etc, complete .


11000038-HD-11370



220 UPVC PIPE - 40 MM, 4KG/SQCM Running Metre 75.00






226 NAHANI (FLOOR) TRAP Each 201.00

227 CI PIPES, IS:3989, 75 MM DIA Running Metre 640.00



230 STONE WARE PIPES-100 MM Running Metre 265.00

231 STONE WARE PIPES-150 MM Running Metre 396.00

Same as item no.218 but of size 80 mm.

UPVC PIPES: Providing and laying unplasticised polyvinyl chloride (UPVC) pipes of class IV or as applicable conforming to IS 4985:2000/ IS 15328 : 2003/IS 13592 : 1992 Type B/ BS 4514/ BS EN 1329, latest edition including all necessary fittings conforming to IS 14735 : 1999/ BS 4514/ BS EN 1329, latestedition and other accessories including connections etc., complete as per drawings or as directed at site. Size 40 mm

Same as item no. 220 but for size 63 mm.

Same as item no.220 but for size 90 mm.




NAHANI (FLOOR) TRAP Providing and fixing PVC floor trap of self cleansing design conforming to IS specs with 100mm inlet, 75mm outlet and 150mm CPhinged grating of 6mm thick with rim. Rate shall include making all necessary leak proof connections etc. complete.

CI PIPES Providing and laying ISI marked 75 mm dia. centrifugally cast (spun) Iron pipes conforming to IS 3989 :1984 latest edition incuding all bends, joints,Ts, cowls etc. with painted MS clampings of appropriate strength @ 1 m c/c. The pipe will be painted with two coats of red oxide and smoke tested aftermaking joints and before joining to the system. The joints will be socket spigot caulked joints with juite and molten lead/Drip Seal as per relevant BISspecifications and procedures. Make - NECO/ HEPCO/ ACL or approved Equivalent

CI PIPES Providing and laying ISI marked 100 mm dia. centrifugally cast (spun) Iron pipes conforming to IS 3989 :1984 latest edition incuding all bends,joints, Ts, cowls etc. with painted MS clampings of appropriate strength @ 1 m c/c. The pipe will be painted with two coats of red oxide and smoke tested aftermaking joints and before joining to the system. The joints will be socket spigot caulked joints with juite and molten lead/Drip Seal as per relevant BISspecifications and procedures. Make - NECO/ HEPCO/ ACL or approved Equivalent

CI PIPES Providing and laying ISI marked 150 mm dia. centrifugally cast (spun) Iron pipes conforming to IS 3989 :1984 latest edition incuding all bends,joints, Ts, cowls etc. with painted MS clampings of appropriate strength @ 1 m c/c. The pipe will be painted with two coats of red oxide and smoke tested aftermaking joints and before joining to the system. The joints will be socket spigot caulked joints with juite and molten lead/Drip Seal as per relevant BISspecifications and procedures. Make - NECO/ HEPCO/ ACL or approved Equivalent

STONE WARE PIPES Providing and laying 100mm dia. salt glazed stoneware pipes conforming to IS 651 Grade-A including bends, tees etc, excavation oftrenches, 100 mm thick 200 mm wide PCC 1:4:8 bedding, PCC 1:5:10, 150 mm thick encasing all around pipe, filling the joints with tarred gasket, plasteringwith 1:3 cement mortar, smoke testing of joints, backfilling the trenches with excavated earth, watering, ramming etc., complete.


11000038-HD-11370



232 GULLY TRAP WITH CHAMBER Each 1391.00

233 SEPTIC TANK (25 persons) Each 25244.00

234 SOAK PIT 2.5(DIA)X3(DEP)M INT. Each 12584.00

235 CI COVER 450X450MM - 16 KG Each 675.00

236 CI COVER 600X600MM - 34 KG Each 1450.00

237 POINT WIRING MDLR PLATE SWITCH Each 500.00

238 5A SOCKET,5A SWITCH SAME BOARD Each 420.00

239 5A SOCKET,5A SWITCH INDPNDNT…. Each 525.00

240 5/15A,15A SWITCH INDEPENDENT Each 685.00

241 AC POINT 20 A INCL. SPMCB Each 1650.00

242 4X10+1X6 SQMM MULTIST. FRLS CU Running Metre 320.00

STONE WARE PIPES Providing and laying 150mm dia. salt glazed stoneware pipes conforming to IS 651 Grade-A including bends, tees etc, excavation oftrenches, 100 mm thick 250 mm wide PCC 1:4:8 bedding, PCC 1:5:10, 150 mm thick encasing all around pipe, filling the joints with tarred gasket, plasteringwith 1:3 cement mortar, smoke testing of joints, backfilling the trenches with excavated earth, watering, ramming etc., complete.

GULLY TRAP WITH CHAMBER Providing and fixing square mouth gully trap including constructing 300 X 300 MM internal size brick masonry chamberwith 230mm thick brick masonry in 1:5 cement mortar, excavation, 75mm thick PCC 1:4:8 bed, plastering with neat cement finish, Medium duty CI cover withframe etc. complete.

SEPTIC TANK (25 persons) : Providing & constructing septic tank of size 1200x2000x1800mm(Internal dimension) with excavation ,PCC1:4:8 100mm thickbed , 345/230mm thick brick masonry wall in CM 1:5 ,RCC1:2:4 100mm thick slab with 8mm tor steel @150c/c both way , 115mm thick baffle wall with RCCbeam at bottom ,12mm thick smooth cement plaster with water proofing compound inside and exposed outside portion, providing 600mmx600mm sizemedium duty CI cover, providing 75mm dia PVC vent pipe etc. complete. Septic tanks of larger capacity may be made utilising different items as components, measured and paid accordingly as per relevant item specifications andrates.

SOAK PIT Providing and constructing soak pit of 2.5m dia X 3m depth (internal) in brick masonry of class 75 design. Internal size of shaft shall be minimumclear 1m with minimum 230thk. walls in cement mortar 1:6 at top 500mm in height and in bottom 230mm wall in height with 450mmx450mm dry brick honeycomb shaft and surrounded by broken brick bats. The outer walls of the shaft should be 230 mm followed by 150 mm thick layer of 50-80 mm nominal sizebrick aggregates thereafter followed by 150 mm thick layer.

CI covers for Chambers / Inspection chambers etc : Supply and fixing of CI cover and frame of 450X450 mm nominal size(total weight not less than 16 kg)with seal, all materials and labour complete.

Same as Item no. 235 but of size 600x600 mm and total weight not less than 34 kg.

POINT WIRING FOR LIGHT/FAN WITH PLATE SWITCHES ANCHOR ROMA/MK/FINOLEX/HAVELLS-CRABTREE / SSK Providing and laying pointwiring in concealed conduits for the following points using specified 1100V grade PVC insulated, FRLS multistranded 3 x 1.5 sqmm copper conductor wires.Rate to include supplying, laying and securing in position in roof slabs and brick walls or concrete columns 25 mm dia medium duty rigid PVC conduits(Conforming to IS 9537:Part 3: 1983) of approved make with necessary accessories and junction boxes/pull boxes. Providing and fixing in the brick wallsflush type metal switch boxes of approved make shade and sufficient size to accommodate all 6A Modular switches / 3 pin socket, screws, holders. ceilingroses and the fan regulator wherever required.

Rate to include wall chasing and rough plastering. Providing and fixing single pole 5A modular plate switches of ANCHOR ROMA/MK/FINOLEX/HAVELL-CRABTREE/SSK make of approved colour . One switch shall be provided for each light and fan point. Rate to include providing main circuit wiring from DB to switch boards with 2.5 sqmm copper wires. All wires shall be conforming to IS 694:1990.

Same as item no. 237 but for 5A socket controlled by one 5A switch on the same lighting board.

Same as item no. 237 but for 5A socket controlled by one 5A switch independently mounted including providing wiring with 3 runs of 1.5 sqmm pvc insulatedcopper wire through PVC conduit.

Same as item no.237 but for 5/15A socket controlled by 15A switch independently mounted including providing wiring with 2 runs of 2.5 sqmm and 1 run of1.5 sqmm PVC insulated copper wire through PVC conduit.

Same as item no.237 but for AC point with 2 runs of 4 sqmm (P&N) and 1 run of 2.5 sqmm (earthing) PVC insulated , FRLS multistrand copper cable in25 mm dia PVC conduit from MCBDB to 20 A power socket. The conduit shall be partly/fully concealed in all types of wall, ceiling etc complete with allaccessories, wiring, termination, connected civil works, rough plastering etc including supply and fixing of 20A industrial socket controlled by 20A SPMCB ofMDS / HAVELS / INDOKOPP / STANDARD make.


11000038-HD-11370





245 3X10 SQMM MULTIST. FRLS CU Running Metre 220.00

Same as item no. 242 but supply, laying, and commissioning of wiring 3x10 sqmm FRLS multistranded copper wire in40mm PVC conduit

246 3X6 SQMM MULTIST. FRLS CU Running Metre 160.00

247 FRLS MULTISTR. 1.5 SQMM COPPER Running Metre 14.00




251 18 SWG PVC INSUL. COPPER WIRE Running Metre 10.00

252 PVC CONDUIT MED. IS:9537-25MM Running Metre 16.00



255 63A TPN MCB DB INCOMER Each 6758.00

256 32A TPN MCB DB INCOMER Each 5460.00

257 CEILING FANS SWEEP:1400 mm Each 1625.00

258 305 MM DIA EXHAUST FAN Each 1480.00

Supply, laying, and commissioning of wiring using 4 runs of 10 sqmm and 1 run of 6 sqmm PVC insulated , FRLS, unsheathed, multistranded copper wiresconforming to IS 694:1990 in 40 mm dia medium duty PVC conduit (Conforming to IS 9537:Part 3:1983) from panel to Distribution boards. Rate to includesupply of 16 GI fish wire, conduits & accessories, wiring, terminations etc complete.

Same as item no. 242 but supply, laying, and commissioning of wiring using 4 runs of 6 sqmm and 1 run of 4 sqmm FRLS multistranded copper wire in 32mm dia PVC conduit from panel to Distribution boards.

Same as item no. 242 but supply, laying, and commissioning of wiring using 4x6 sqmm and 2x4 sqmm FRLS multistranded copper wire in 40mm PVCconduit

Same as item no. 242 but supply, laying, and commissioning of wiring 3x6 sqmm FRLS multistranded copper wire in 40mm PVC conduit

Supply and laying through conduit FRLS multistranded PVC insulated (1100V) copper wire conforming to IS 694:1990 and of size 1.5 sqmm includingtermination etc. all complete. PVC Conduits to be paid for separately as per relevant items.

Same as item no. 247 but size 2.5 sqmm



Same as item no. 247 but for single core PVC insulated copper wire 18 SWG.

Supply and laying rigid non-flame propagating medium duty PVC conduit 25 mm dia. conforming IS 9537(Part III) including all bends, clamps, joineries, fixingon the wall etc. all complete

Same as item no. 252 but 32 mm dia

Same as item no. 252 but 40 mm dia

Supply, installation and commissioning of 63A TPN MCB DB Incomer : 1 no 63 A , 4 Pole MCB Outgoing : 18 nos, 10A/16A/20A SP MCBs

Supply, installation and commissioning of 32A TPN MCB DB Incomer : 1 no 32 A , 4 Pole MCB Outgoing : 12 nos, 10A/16A/20A SP MCBs

CEILING FANS Supplying and fixing of the ceiling fans of Khaitan / GE / Polar / Usha with detail as below : Sweep:1400 mm Colour : white Bearing type :Double ball bearing Down rod : as per requirement Regulator : Electronic type ANCHOR ROMA/MK Accessories :Screws, wall nuts etc. complete.


11000038-HD-11370



259 230 MM DIA EXHAUST FAN Each 1250.00

260 LIGHT FIXT.&LAMP-TMC501/136HPF Each 725.00

261 LIGHT FIXT. &LAMP-DGN 451 Each 1275.00

262 BULK HEAD & LAMP-NXC 101 Each 500.00

263 ANGLE HOLDER WITH LAMP Each 53.00

264 MIRROR OPTIC FTG.-TCS605/236M1 Each 2050.00

265 MIRROR OPTIC FTG.-TBS300/418M1 Each 2800.00

266 CORNER LUMINAIRE-ACW/N- 1X18W Each 975.00

267 CORNER LUMINAIRE-ACW/N- 1X36W Each 1125.00

268 DECORATIVE LUMINAIRE-AMA-1X18W Each 1025.00

269 DECORATIVE LUMINAIRE-AMA-1X36W Each 920.00

270 ENERGY ESSENTIALS- 11 W Each 150.00



273 HALOGEN DICHROIC SPOT LIGHT Each 865.00

274 TELEPHONE SOCKET POINT 2 PAIRS Running Metre 48.00

275 TELEPHONE TAG BLOCK 5 PAIRS Each 970.00

Supply, fixing and commissioning of 305 mm dia Exhaust fans with metal alloy blades including bird louvers, frame works and other civil works like chippingand making the surface good etc. Make : Crompton / khaitan / Bajaj.

Same as item no. 258 but of 230MM Dia.

Supply, fixing and commissioning of box type light fitting Philips make cat no. TMC501/136 HPF (High Power Factor) 1 x 36 W tube light fitting with lamp orequivalent of Crompton make Cat. DJB 14. Rate to include all accessories, interconnection of wires from ceiling rose to the fittings and fluorescent tube lamps, copper ballast etc.

Same as item no. 260 but 1 x 60W spot light luminaire with 1 meter track including lamp Philips make cat no. DGN 451 or equivalent of Crompton make fordisplay shelving

Same as item no. 260 but 1 x 40 W Bulk head luminaire including lamp Philips cat no. NXC 101 or equivalent Crompton make Cat. CBHE 29 ( Outsidebuilding).

Same as item no. 260 But Angle holder Anchor make including lamp 60W.

Same as item no. 260 but 2 x 36 W indoor decorative surface mounted tube light fitting including lamp Philips cat no TCS 605/236 M1 HPF (High PowerFactor) or equivalent of Crompton make Cat. CBSW 1124 HSB.

Same as item no. 260 but 4 x 18 W indoor decorative mirror optics luminaire suitable for recessed mounting including 4 nos. TL D lamps Philips cat no TBS300/418 M1 HPF (High Power Factor) or equivalent of Crompton make Cat. CRFN 42 HSB.

Same as item no.260 but Corner/wall slim (corner luminaire with lamp, reflector clear receded acrylic cover Arcade make). 1X18W

Same as item no.260 but Corner/wall slim (corner luminaire with lamp, reflector clear receded acrylic cover Arcade make). 1X36W

Same as item no.260 but Decorative luminaire with lamp reflector, opal/clear receded acrylic cover Arcade make. 1X18W

Same as item no.260 but Decorative luminaire with lamp reflector, opal/clear receded acrylic cover Arcade make. 1X36W

Same as item no.260 but supply and fixing energy essential CFLs 11 W of PHILIPS make. Approved equivalent - Havell/ Osram



Same as item no.260 but supply & fixing of spot lights in sales room opposite to sales display shelving using PHILIPS make cat 303-2 x 12V, 50W halogenDichroic or equivalent inclusive of Necessary connection, accessories, lamp etc. complete.

TELEPHONE SOCKET POINT Supply and laying 2 pairs of 0.5 mm dia screened and shielded telephone wire in 20 mm dia PVC conduit partly/fullyconcealed in types of walls , floor etc complete with all accessories , wiring terminations, connected civil works, rough plastering etc including supply of 16 GIfish wire conduit & accessories etc.

Supply, fixing and commissioning of following 5 pairs of telephone tag block of Krone type enclosed in suitable MS box. Rate shall include all accessories,connected civil works for fixing the same as per specifications.


11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATE276 MODULAR TELEPHONE SOCKET Each 265.00

277 WALL MOUNTING METER BOARD Each 5610.00

278 FLR.MNT.PANELBOARD-2X125/2X63A Each 52415.00

279 FLR.MNT.PANELBOARD-2X63/4X32A Each 45815.00

280 25 KVA LT PANEL- HENSEL Each 95000.00

281 S/L 3.5CX150SQMM ARMD.AL CABLE Running Metre 700.00


283 S/L 3.5CX95 SQMM ARMD.AL CABLE Running Metre 485.00

Same as Item No.281 but 3.5CX95 sqmm AL cable.







Supply and installation of modular type telephone socket MK make or equivalent in a suitable size box concealed to wall including all civil works.

Supply and fixing of wall mounting type meter board made out of 16 SWG CRCA sheet steel and single iron with 3 nos 200A Fuse cutouts N.L., 1 no earthbus and space for accommodating 1 no. 3 ph, 4 wire KWH meter complete with adequate size of copper wire interconnections, powder coating etc. complete.

Supply and erection, testing commissioning of floor mounting type cubical panel board made out of 16 SWG CRCA sheet steel with 200 A TPN copper busbars, interconnections, earthing, powder coating and comprising of the followings as required.

Incomer : 2 nos 125A TP switch fuse unit with HRC fuses for DG and EB 1 no 125A 4 pole change over switch 2 no volt meter with volt meter selector switch,2 no ammeter with C T & ammeter selector switch, 2 sets of Phase indicating lamp (RYB) Outgoing : 2 nos 63A and 3 nos 32A TP fuse switch unit withHRC fuse.

Same as item no.278 but with following details Incomer : 2 nos 63A TP switch fuse unit with HRC fuses for DG and EB 1 no 63A 4 pole change over switch2 no volt meter with volt meter selector switch, 2 no ammeter with C T & ammeter selector switch, 2 sets of Phase indicating lamp (RYB) Outgoing : 4 nos32A TP fuse switch unit with HRC fuse.

Design, fabrication, supply, installation, testing and commissioning of factory made LT switch board/ panel of Make - HENSEL made out of polycarbonate, polyestrene thermoplastic modules/enclosure with IP 65 degree of protection. Please refer to attched specifications, list of items, bill of materials and drawing nos. HENMIPDB31705 for details. Approved Equivalent - Fybox, Rittal

Bus Bar Rating: 250 A (12x10, 12x5 mm Cu), System Voltage: 415 V, 50 HzIncomer: 125A FP COS - 1No.; 100A TPN SFU - 1No.; 70A Contactor - 1No.Outgoings: 32A FP ISOLATOR - 1 No.; 32A FP MCB - 2 Nos.; 20A DP MCB - 2 Nos.; 32A DP MCB - 14 Nos.; 10A DP MCB - 17 Nos.; 40A FP ISO - 1 No.

Metering: Voltmeter with selector switch (0-500V) - 1 No.; Ammeter with selector switch (0-63A) - 1 No.; Frequency Meter - 1 No.; CurrentTransformer(63/5A) - 3 Nos.; R/Y/B LED Indication - each 1 No.; On/Off PB - each - 1 no.; Control Fuse with Base - 6 Nos. Terminals: 50 Sqmm Feed in Terminals - 10 Nos.; 6 Sqmm - 85 Nos.; 4 Sqmm Earth Terminals - 35 Nos. Rate to include approved front cable cover, pedestalframe with FRP lining and canopy as per manufacturer's specifications.

Note: For any outlet having requirement of more than 25 KVA load, the panel has to be separately designed using the above basic material of approvedmanufacturers. The payment shall be made separately basis the original quotation received from manufacturer and approved by HPCL Engg.-in-Charge.

Supply and laying insulated, sheathed, armoured LT cable of approved make and conforming to .IS 1554:Part 1:1988. 3.5CX150 sqmm AL cable XLPE



11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATE287 S/L 3.5CX25 SQMM ARMD.AL CABLE Running

Metre 180.00Same as Item No.281 but 3.5CX25 sqmm AL cable.

288 S/L 4CX16 SQMM ARMD. AL CABLE Running Metre 145.00

Same as Item No.281 but 4CX16 sqmm AL cable.







292 S/L 4CX2.5 SQMM ARMD. CU CABLE Running Metre 150.00

Same as Item No.281 but 4CX2.5 sqmm copper cable.











298 S/L 3CX10 SQMM UNARMD.CU CABLE Running Metre 320.00

Same as Item No.281 but 3Cx10 sqmm unarmoured copper cable

299 S/L 3CX6 SQMM UNARMD. CU CABLE Running Metre 200.00






302 END TERM., NFLP, 3.5 Cx150 AL Each 940.00




End termination of 3.5CX150 sqmm armoured AL cable cable with double compression NFLP gland and crimping sockets.




11000038-HD-11370






309 END TERM., NFLP, 4 Cx16 AL Each 215.00

310 END TERM., NFLP,4CX10 AL Each 200.00

311 END TERM., NFLP, 4 Cx6 AL Each 145.00

312 END TERM., NFLP,2CX6 AL Each 145.00

313 END TERM., NFLP, 4 Cx2.5 AL Each 140.00






319 END TERM.,FLP GLAND,3Cx2.5 CU Each 190.00

320 END TERM.,FLP GLAND,4Cx2.5 CU Each 200.00

321 WELDING CABLE 16 SQMM COPPER Running Metre 68.00

322 50 NB GI PIPE: CLASS B,IS1239 Running Metre 300.00

323 63 NB GI PIPE: CLASS B,IS1239 Running Metre 370.00





End termination of 4CX16 sqmm armoured AL cable cable with double compression NFLP gland and crimping sockets.




End termination of 4CX2.5 sqmm armoured AL cable cable with double compression NFLP gland and crimping sockets.






End termination of 3CX2.5 sqmm copper cable with double compression FLP gland and crimping sockets.

End termination of 4CX2.5 sqmm copper cable with double compression FLP gland and crimping sockets.

Supply/laying/fixing welding cable 16 sqmm of rating 174 A and conforming to IS 9857:1990 having gasoline resistant insulation and multistranded copperconductors. Rate includes end terminations, sockets and thimbles complete.

Supply and laying 50mm dia GI pipe of approved make conforming to IS 1239 medium duty including threading, suitable GI collars, bends, elbow, nipples etc.all complete.


11000038-HD-11370



324 100NB GI PIPE: CLASS B,IS1239 Running Metre 525.00

325 CABLE TRENCH Running Metre 95.00

326 JUNCTION BOX -YARD LIGHT POLE Each 640.00

327 OUTDOOR LOOP-IN-LOOP OUT BOX Each 425.00

328 GI Oct.Light Pole-SingleArm 6m Each 13050.00

329 GI Oct.Light Pole-DoubleArm 6m Each 13650.00



Supply and laying 63mm dia GI pipe of approved make conforming to IS 1239 medium duty including threading, suitable GI collars, bends, elbow, nipples etc.all complete.

Supply and laying 100 mm dia GI pipe of approved make conforming to IS 1239 medium duty including threading, suitable GI collars, bends, elbow, nipplesetc. all complete.

Excavation in any type of soil including WBM/asphalt up to 600mm depth and 300mm wide including supply and laying 150mm thick sand on top and bottomof cable, supply and laying bricks of designation 50 laid flat on top, back filling trench by earth only etc. complete.

Supplying and fixing flame proof and weather proof junction box of Sudhir / Baliga make out door junction box of IP 54 category of protection with rubbergasket and having locking arrangement including all required connectors, 10A SPMCB.

Supply, installation, testing and commissioning of outdoor type loop-in-loop out- box with suitable terminals to receive the incoming Al / Cu cable and 6 sets ofoutgoing AL/ Cu wires of required size. The loop-in-loop-out box shall be suitable for fixing in angle iron frame work.

Supply and installation of BAJAJ make Hot dip galavanised iron pole having wall thickness 3 mm. C/s A/F - top = 70mm, bottom =130 mm, base plate220x220x12 mm, 500 mm long weatherproof reinforced door opening with junction box mounting arrangement but exclusive of junction box, single armbracket 1 m, 20mm dia. threaded made to J shape and having 600 mm total length steel grade EN8 foundation bolts - 4 nos with nuts, templates and allcomplete as per approved drawing. Approved Equivalent Make - PHILIPS

Foundation RCC 1:1.5:3 shall be of size 550x550mm and depth 1200 mm with 8 nos. 12mm dia. tor bars as main bars and 8mm dia. tor bars stirrups @ 190mm c/c as per approved drawing. This reinforcement shall conform to IS:1786 latest edition. The foundation shall extend above sorrounding ground/drivewaylevel for 200 mm and have slant 63mm dia. PVC sleeve cast insitu foundation for cable entry as per the drawing. Excavation, PCC, RCC and reinforcementshall be done and paid extra as per relevant items.

Supply and installation of BAJAJ make Hot dip galavanised iron pole wall thickness 3 mm. C/s A/F - top = 70mm, bottom =130 mm, base plate 220x220x12mm, 500 mm long weatherproof reinforced door opening with junction box mounting arrangement but exclusive of junction box, double arm brackets 1 m each,20mm dia. threaded made to J shape and having 600 mm total length steel grade EN8 foundation bolts - 4 nos with nuts, templates and all complete as perapproved drawing. Approved Equivalent Make - PHILIPS

Foundation RCC 1:1.5:3 shall be of size 550x550mm and depth 1200 mm with 8 nos. 12mm dia. tor bars as main bars and 8mm dia. tor bars stirrups @ 190mm c/c as per approved drawing. This reinforcement shall conform to IS:1786 latest edition. The foundation shall extend above sorrounding ground/drivewaylevel for 200 mm and have slant 63mm dia. PVC sleeve cast insitu foundation for cable entry as per the drawing. Excavation, RCC and reinforcement shallbe done and paid extra as per relevant items.

Supply and installation of BAJAJ make Hot dip galavanised iron pole wall thickness 3 mm. C/s A/F - top = 70mm, bottom =130 mm, base plate 220x220x12mm, 500 mm long weatherproof reinforced door opening with junction box mounting arrangement but exclusive of junction box, singler arm bracket 1 m, 20 diathreaded made to J shape and having 600 mm total length steel grade EN8 foundation bolts - 4 nos with nuts, templates and all complete as per approveddrawing. Approved Equivalent Make - PHILIPS.



11000038-HD-11370





334 STREETLIGHT FITTING CRP330/150 Each 7800.00

335 HOARDING LIGHT QVF 135/70 Each 3450.00

336 ONLY FIXING LIGHT FITTING Each 340.00

337 EARTHING PIT-PLATE ELECTRODE Each 7500.00

338 EARTH PIT-PLT ELEC.W/O CHAMBER Each 4500.00

Supply and installation of BAJAJ make Hot dip galavanised iron pole wall thickness 3 mm. C/s A/F - top = 70mm, bottom =130 mm, base plate 220x220x12mm, 500 mm long weatherproof reinforced door opening with junction box mounting arrangement but exclusive of junction box, double arm brackets 1 m each,20mm dia. threaded made to J shape 700 mm long steel grade EN8 foundation bolts - 4 nos with nuts, templates and all complete as per approved drawing.Approved Equivalent Make - PHILIPS.


Supply and installation of BAJAJ make Hot dip galavanised iron pole wall thickness 3 mm. C/s A/F - top = 70mm, bottom =135 mm, base plate 225x225x16mm, 500 mm long weatherproof reinforced door opening with junction box mounting arrangement but exclusive of junction box, singler arm bracket 1 m, 20 diathreaded made to J shape 750 mm long steel grade EN8 foundation bolts - 4 nos with nuts, templates and all complete as per approved drawing. ApprovedEquivalent Make - PHILIPS.

Foundation RCC 1:1.5:3 shall be of size 550x550mm and depth 1500 mm with 8 nos. 12mm dia. tor bars as main bars and 8mm dia. tor bars stirrups @ 190mm c/c as per approved drawing. This reinforcement shall conform to IS:1786 latest edition. The foundation shall extend above sorrounding ground/drivewaylevel for 200 mm and have slant 63mm dia. PVC sleeve cast insitu foundation for cable entry as per the drawing. Excavation, PCC, RCC and reinforcementshall be done and paid extra as per relevant items.

Supply and installation of BAJAJ make Hot dip galavanised iron pole wall thickness 3 mm. C/s A/F - top = 70mm, bottom =135 mm, base plate 225x225x16mm, 500 mm long weatherproof reinforced door opening with junction box mounting arrangement but exclusive of junction box, double arm brackets 1 m each,20 dia threaded made to J shape 750 mm long steel grade EN8 foundation bolts - 4 nos with nuts, templates and all complete as per approved drawing.Approved Equivalent Make - PHILIPS.


Supply and fixing Philips make Cat. CRP 330 street light fixture (IP65) with Ceramic Discharge CDMTT 150W lamp (Make Philips/ Osram) and single piecedie cast aluminium housing with all accessories energy efficient copper ballast, heat resistant toughened flat glass cover, electronic ignitor, reflector' powerfactor improvement capacitor etc. complete. Approved equivalent of Bajaj make Aqua Wave Series Cat. BGWRL 150 MH SE FFG with 150 W CeramicDischarge CDMTT lamp and approved equivalent of Crompton make MHSGT1215IH/G with Lamp 150WCDM-TT . The job includes fixing the street lightfixtures, providing flexible wire of 7/20 copper wire of approved make, from junction box to top of the pole.

Supply and fixing Philips make Cat. QVF 135 hoarding light fixture (IP54) with Metal Halide MHN-TD 70W lamp, control gear box, light weight corrosion-resistant pressure die cast housing with universal mounting bracket, all accessories energy efficient copper ballast, heat resistant toughened glass cover,electronic ignitor, reflector, power factor improvement capacitor etc. complete. Approved equivalent Crompton make Cat. TH 6 MH(DE). The job includesfixing the street light fixtures and wiring as approved.

Same as item no. 335 but to fix the HPCL supplied street light fixtures.

Providing plate electrode earthing as per IS 3043 and attached drawing including excavation of depth 3.2 m, supplying and fixing plate electrode of size600x600 mm and thickness 6.3 mm (GI) or 3.15 mm (Copper), 50mm dia GI pipe of heavy duty (wall thickness 4.5 mm) with funnel for watering, wire mesh,GI flat (2 nos. 50x6 mm ) collars, two connecting GI strips (50x6 mm) from plate electrode to collar, fixing & using using GI nut bolts with bitumen coating andwelding as per drawing, filling the pit with alternate layers of charcoal and salt, back filling, constructing 230 mm thick Brick Masonry chamber1000(length)x500(width)x600 (depth) mm internal size with plastering 10 mm thick and embedded 50 mm dia PVC conduit openings at two places packedwith jute soaked in bitumen at the entrances, 100mm thick PCC 1:3:6 at the bottom of chamber, providing 3 mm thick MS sheet cover with diagonal bracingsof 25x3 mm flats, frame and hinge arrangement covering full opening, grouting the cover frame in PCC 1:2:4 bed 230x75 mm, painting two coats of approvedcolour synthetic enamel paint over a coat of red oxide primer etc. complete. Rate includes carrying out earth resistance testing of the earth pit provided, submitting report and painting resistance, test date and pit identification no. oncover top.


11000038-HD-11370



339 EARTHING PIT- PIPE ELECTRODE Each 4800.00

340 EARTH PIT-PIPE ELEC.W/O CHMBER Each 3600.00

341 10 SWG COPPER WIRE Running Metre 43.00

342 25X3 COPPER FLAT Running Metre 303.00

343 25X6 GI FLAT Running Metre 70.00

344 50X6 GI FLAT Running Metre 140.00

345 MS CHEQUERED PLATE KG 66.00

346 MS EDGE PROTECTION KG 57.00

347 ISI MARKED RUBBER MAT-20MM Square Metres 750.00

3 PHASE SERVO STABILISER-25KVA Each 66000.00348

349 3 PHASE SERVO STABILISER-40KVA Each 105000.00

350 5/6 KVA Each 25000.00351 9/10 KVA Each 34500.00352 15KVA Each 36500.00353 20 KVA Each 47000.00

Earthing Pit-Plate Electrode without chamber:Same as item no. 337 but without chamber and covers. The item is for providing earthing pit under driveway.The chamber and cover shall be provided with same specifications as of driveway chambers and as per instructions of Engg.-In-Charge. The drivewaychambers shall be paid as per respective item rate.

Providing pipe electrode earthing as per IS 3043 and attached drawing including excavation of depth 3.75 m, supplying and fixing pipe electrode of size 50 mmdia heavy duty (wall thickness 4.5 mm) GI pipe with funnel for wateing, wire mesh, GI flat (50x6 mm) collar joined to pipe using 50x6 mm strip and GI nut boltswith bitumen coating as per drawing, filling the pit with alternate layers of charcoal and salt, back filling, constructing 230 mm thick Brick Masonry chamber400(length)x400(width)x400 (depth) mm internal size with plastering 10 mm thick and embedded 50 mm dia PVC conduit openings at two places packed withjute soaked in bitumen at the entrances, 100mm thick PCC 1:3:6 at the bottom of chamber, providing CI cover with CI frame in hinge arrangement coveringfull opening, grouting the cover frame in PCC 1:2:4 bed 230x75 mm, painting two coats of approved colour synthetic enamel paint over a coat of red oxideprimer etc. complete. Rate includes carrying out earth resistance testing of the earth pit provided, submitting report and painting resistance, test date and pit identification no. oncover top.

Earthing Pit-Pipe Electrode without chamber:Same as item no. 339 but without chamber and covers. The item is for providing earthing pit under driveway. Thechamber and cover shall be provided with same specifications as of driveway chambers and as per instructions of Engg.-In-Charge. The driveway chambersshall be paid as per respective item rate.

Supply and fixing 10 SWG copper wire for earthing connection to pumps, canopy columns etc.

Supply and fixing 25x3 copper flat for earth connection of panel / interconnection of earth pits.

Supply and fixing 25x6 GI flat for earth connection of panel / interconnection of earth pits.

Supply and fixing 50x6 GI flat for earth connection of panel / interconnection of earth pits.

Providing and fixing 6mm thick MS chequered plate including making holding arrangements, painting with two coats of red oxide primer and two coats ofsynthetic enamel paint etc.

Providing and fixing MS angle / channel supports and edge protection for trench etc. including providing hold fast ,painting with two coats red oxide primerand two coats of synthetic enamel etc.

Supply and fixing 20mm thick ISI marked rubber mat of approved make.

Supply , installation and commissioning of 3 phase oil cooled balanced / unbalanced load servo controlled voltage stabilisers (Make - Logicstat / Blue bird / Bhurji / HPCL approved make) including auto / manual control, overload trip relay, low / high voltage cut-off, single phase protector, cost of oil. Rate includes making input and output connection but excludes supply of necessary cables, lugs and clamping. Party to furnish manufacturer's test certificate alongwith supply and provide warranty/gaurantte for a period of one from the date of installation..

Supply , installation and commissioning of 3 phase air cooled balanced / unbalanced load servo controlled voltage stabilisers (Make - Logicstat / Blue bird / Bhurji / HPCL approved make) including auto / manual control, overload trip relay, low / high voltage cut-off, single phase protector. Rate includes making input and output connection but excludes supply of necessary cables, lugs and clamping. Party to furnish manufacturer's test certificate alongwith supply and provide warranty/gaurantte for a period of one from the date of installation.


11000038-HD-11370



354 2 KVA Each 3000.00355 5 KVA Each 4000.00356 7.5 KVA Each 7000.00357 10 KVA Each 12000.00

358 100 VA CVT Each 3000.00359 250 VA CVT Each 4000.00360 500 VA CVT Each 6775.00361 TANK INSTALLATION-45KL Each 20240.00

362 TANK INSTALLATION-35KL Each 18040.00



365 TANK INSTALLATION- 9KL Each 9240.00

366 PUMP ISLAND: 0.9 M WIDE Running Metre 1044.00

367 INSTALLATION MONO PUMPS Each 350.00

368 INSTALLATION DUAL PUMPS Each 625.00

369 INSTALLATION MPD PUMPS Each 725.00

370 MS ERW PIPE,IS1239,”C”,40NB Running Metre 440.00

Supply , installation and commissioning of single phase voltage stabilisers (range 160V - 260V) of approved Make - Logicstat / Blue bird / Bhurji / HPCL approved make. Rate includes overload trip relay, low / high voltage cut-off, Rate also includes making input and output connection but excludes supply of necessary cables, lugs and clamping. Party to furnish manufacturer's test certificate alongwith supply and provide warranty/gaurantte for a period of one from the date of installation.

Supply and fixing of constant voltage transformer of aproved make - Logicstat, Blue bird, Sukam, Bhurji or equivalent. Party to furnish manufacturer's test certificate alongwith supply and provide warranty/gaurantte for a period of one from the date of installation.

Installation of HPCL supplied Tanks of 45 KL capacity in earth pit /brick masonry pit. Job includes Hydrostatic testing to pressure of 3.5m water column,supplying & filling with water with necessary 50 mm dia pipe & on successful completion emptying out the water from tank , cleaning & drying the innersurfaces with cloth/ cotton waste etc., doping with two coats tank mastic paint of STP make and hot 30/40 bitumen ( total doping thickness 3mm) ,fixing allfittings etc.

Job excludes excavation, PCC, RCC, BM, plastering, which shall be paid seperately as per drawing and actual measurement at site as approved by Engg.-In-Charge. cost of fittings, cost of pipelines, check valves shall be paid separately on actual basis. Rate to include providing and fixing locking / capingarrangement in all fill pipes / suction pipes / dip pipe etc. as directed by Engg.-In-Charge.

Same as item no. 361 but for 22 KL tank



Island : Providing and constructing pump island of 0.9m width and 0.3m height from finished driveway level and 0.6m below the finished d/w level using BM inCM 1:5 and filling river sand inside with necessary foundation in 100 mm thick PCC 1:3:6 and average 12mm thick rough cement plaster in CM 1:4 on outerside. The job includes necessary excavation, labour etc all complete. Any Brick work below 0.6m in foundation will be paid seperately.

Installation of MONO pumps on pedestal including providing & fixing foundation bolt in PCC 1:2:4 & connecting suction pipe, electrical, earthing connectionsto the pump etc. complete.

Installation of DUAL pumps on pedestal including providing & fixing foundation bolt in PCC 1:2:4 & connecting suction pipe, electrical, earthing connections tothe pump etc. complete.

Installation of MPD pumps on pedestal including providing & fixing foundation bolt in PCC 1:2:4 & connecting suction pipe, electrical, earthing connections tothe pump etc. complete.

Supplying & Laying 40 mm NB Heavy-duty 'C' Class MS Steel ERW screwed pipeline Conforming to IS 1239 (part I) – latest edition to the required slope &alignment with heavy duty MS fittings like elbows, tees etc. including doping pipe line with 3 coats of 'Shalimastic HD THIXOTROPIC of STP cold appliedanti corrosive treatment after preparing the surface as per manufacturer specifications. The joints are to be made leak proof by using jointing materials likeLitharge, Shellac, holdite. Pipes laid aboveground shall be painted with two coats of synthetic enamel over two coats of Zinc Chromate primer of approvedquality and shade. The pipeline shall be tested at a pressure of 5Kg / sqcm.



11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATE371 MS ERW PIPE,IS1239,”C”,50NB Running

Metre 480.00

372 MS FILL PIPE C CLASS 80 NB Running Metre 641.00

Supplying and fixing all complete C Class MS fill pipe 80 mm dia. Same as item 370.

373 ANGLR CHECK VALVE-40 MM Each 1390.00

374 ANGLR CHECK VALVE-50 MM Each 1500.00

375 FILL CAP-40 MM Each 375.00

376 FILL CAP-50 MM Each 425.00

377 VENT HOOD-40NB Each 300.00

378 VENT HOOD MS TANK SPRING LOAD. Each 475.00

379 GRANITE SLAB-18MM BLACK Square Metres 2200.00

380 GRANITE TILE-10MM THICK Square Metres 1300.00

381 PIPELINE TRENCH: INT.300X400MM Running Metre 1150.00

382 PIPELINE TRENCH:INT.450X400MM Running Metre 1400.00

383 PRECAST RCC COVER: CLASS AAA Square Metres 2050.00

384 HIGHWAY DRAIN COVER: CLASS AAA Square Metres 3950.00

385 DISMANTLE PUMP ISLAND-1 M WIDE Running Metre 105.00

Same as Item no. 370 but for 50mm NB pipe.

Supply and fixing ISI marked angular check valve of Leader/ Sant/ Syall make. 40 NB

Supply and fixing ISI marked angular check valve of Leader/ Sant/ Syall make. 50 NB

Fill cap, 40 mm : Supply and fixing MS fill cap with locking arrangement including Godrej 6 lever brass lock.

Fill cap, 50 mm : Supply and fixing MS fill cap with locking arrangement including Godrej 6 lever brass lock.

Vent hood : Supply and fixing 40mm dia vent hood (double sided with brass mesh) in vent pipe.

Vent hood for MS tank : Supply and fixing 40mm dia spring loaded vent hood for MS tanks calibrated at given pressure.

Providing and fixing not less than 18 mm thick pre polished water cut black granite slab for pump island top including providing 25mm thick bed cement mortar1:5 (1 cement : 5 coarse sand) ,as per design and chamfered edges. Job includes a coat of floating cement slurry and finishing the joints with white cementmixed with matching colour pigment.

Providing and fixing 10 mm thick pre polished water cut black granite tiles for pump island dado including providing 12mm thick bed cement mortar 1:4 (1cement : 4 coarse sand) , fixing the tiles with neat cement paste and finishing the joints with white cement mixed with matching colour pigment.

Providing pipeline trench with internal size 300mm wide x400mm depth including excavation, 100mm thick PCC 1:4:8, 230mm thick brick masonry in 1:5 CM,12mm thick plastering inside in 1:4 CM, filling trench with sweet river sand. Rate also includes PCC 1:1.5:3 bands 150 mm thick for grouting edge angles,fixing 50x50x6 MS rolled angles on both edges in line and level, cover blocks, two coat synthetic enamel painting of angles over a single coat of red oxideprimer, necessary MS/plywood(minimum 19 mm thick) shuttering/deshuttering, cleaning etc. complete. Additional 12 mm dia MS bars(200 mm in length) in Lshape shall be welded on back of angles @ 200 mm c/c for grouting purpose. The PCC band shall be provided with 3 nos. 8 mm dia tor reinforcement steel,curing etc. complete.

Providing pipeline trench with internal size 450mm wide x400mm depth including excavation, 100mm thick PCC 1:4:8, 230mm thick brick masonry in 1:5 CM,12mm thick plastering inside in 1:4 CM, filling trench with sweet river sand. Rate also includes PCC bands 150 mm thick for grouting edge angles, fixing65x65x6 MS rolled angles on both edges in line and level, cover blocks, two coat synthetic enamel painting of angles over a single coat of red oxide primer,necessary MS or plywood(minimum 19 mm thick) shuttering/deshuttering, cleaning etc. complete. Additional 12 mm dia MS bars(200 mm in length) in L shape shall be welded on back of angles @ 200 mm c/c for grouting purpose. The PCC band shall be provided with 3 nos. 10 mm dia tor reinforcement steel, curingetc. complete.

Providing and laying factory made pre-cast RCC (Concrete Grade – MINIMUM M35) covers with MS lifting lugs of Surabh / KK manhole make or equivalentmeeting the specifications, having thickness 90 mm and size to cover the pipeline trench. The cover shall be suitable for AAA class load (Minimum 35 MTrolling axle load) and shall have MS enclosure of minimum 2 mm thick allaround including reinforcement suitable for load class. The clear opening span oftrench shall not be more than 650 mm

Same as item no.383 but of size 1500 (Length) x 350 (Breadth) x 200 (thickness) mm to cover highway drain openings having clear span not more than 1 m.


11000038-HD-11370



386 EXHUMING 9/11KL TANK Each 3100.00

387 EXHUMING 16/14 KL TANK Each 4650.00

388 EXHUMING 22 KL TANK Each 5150.00

389 EXHUMING 45KL TANK Each 7250.00

390 EXHUMING 70KL TANK Each 9500.00

391 Same as item no. 386 but exhuming under ground tanks of 70 KL capacity. Square Metres 210.00

392 DISMANTLE DOUBLE STOREY BLDG. Square Metres 325.00

393 DISMANTLE COMP. WALL > 1.2 M Running Metre 105.00

394 DISMANTLE COMP. WALL<= 1.2 M Running Metre 50.00

395 SCRAPPING OF PLASTER Square metres 15.00

Breaking the following structures including disposa l of debris as directed :

396 BRICK MASONARY DISMANTLING Cubic Metres 100.00

397 RUBBLE MASONARY DISMANTLING Cubic Metres 100.00

398 CEMENT CONCRETE DISMANTLILNG Cubic Metres 125.00

399 RCC WITHOUT DRILL Cubic Metres 310.00

400 RCC WITH DRILL Cubic Metres 600.00

Dismantling of existing pump island 1m wide and carting away debris including removal of pump and disconnecting pipeline etc. complete.

Exhuming under ground tanks of 9KL /11KL capacity with all fittings from earth pit including disconnecting suction, fill, vent pipe , opening man hole cover,excavation, dewatering if encountered, removing all sludge / oil and storing the same in drums. degassing of tank, stacking the tank as directed by Engg.-In-Charge etc. Complete inclusive back filling with available earth at site inclusive compaction and watering. Back filling by imported earth / sand shall be paidseperately.

Same as item no. 386 but exhuming under ground tanks of 16KL /14KL capacity.

Same as item no. 386 but exhuming under ground tanks of 22 KL capacity.



Single storey building : dismantling of entire structure upto existing ground level, disposal of debris, stacking of steel reinforcement, doors, windows, ACsheets, electrical fittings, aluminium glazing, structural steel etc. Job includes disposal of debris to an unobjectionable place as directed . Plinth area shall bemeasured for payment.

Double storey building : Specs as item no. 391 but double storey

Dismantling of Compound wall of more than 1.2m height and any width. Rest specs as Item No. 391

Dismantling of Compound / kerb wall of upto 1.2m height and any width. Rest specs as Item No. 391

Scrapping / chipping /breaking old plaster from walls and loose RCC work viz, beams, columns, slabs etc and disposing the debris to an unobjectionable areaas directed by the HPCL engineer-in-charge. Rate to include scrapping the plaster with the help of chisel, mallet etc to reach upto the bare brick surface anddisposing alongwith all labour t&p etc required for complete execution.

Dismantling of brick masonary above plinth level only. For masonary below plinth excavation shall be paid separately.

Dismantling of rubble masonary above plinth level only. For masonary below plinth excavation shall be paid separately.

Dismantling of Cement concrete : above plinth level only. For works below plinth excavation shall be paid separately.

Dismantling of RCC structure without pneumatic drill/Jack hammer : Above plinth level only. For masonary below plinth excavation shall be paid separately.


11000038-HD-11370



401 Tiles in flooring / Tiles on wall Square metres 20.00

402 Steel structure dismantling Kilograms 5.00

403 Dismantling of paver tiles Square metres 30.00

404 Roofing sheets Square metres 15.00

405 False ceiling Square metres 25.00

406 EXCAVATION IN RCC Cubic Metres 450.00

407 EXCAVATION IN PCC Cubic Metres 350.00

TRANSPORTATION WORKS

Mini truck load upto 4MT

408 0-50kms Lump Sum 2600.00409 Beyond 50kms Kilometers 18.00410 Detention charges Days 500.00

Full Truck load -upto 10MT

411 0-50kms Lump Sum 5000.00412 Beyond 50kms Kilometers 32.00413 Detention charges Days 700.00

Trailor load upto-20MT

414 0-50kms Lump Sum 7500.00415 Beyond 50kms Kilometers 45.00

Dismantling of RCC with pneumatic drill / Jack hammer : Above plinth level only. For masonary below plinth excavation shall be paid separately.

Dismantling of ceramic tiles of any thickness. Scope of job includes cleaning the bed post dismantling to make it fully prepared for fresh tiling/ flooring.

Dismantling of steel structures as directed by the engineer-in-charge. Scope of job includes cutting or unlocking of nuts and bolts as required for completedismantling of the structure and handing over the entire structure in lengths and sizes as specified. Payment shall be made basis the weight of the handedover materials. In case of canopy/hoarding dismantling it is mandatory to hand over all the nuts and bolts or other joineries in proper bags duly marked.Weighment is to be arranged by the party and witnessed by either the HPCL EIC OR his designated representative. If the material is of meagre quantity,weighment to be done by spring balance at site, otherwise the weighment is to be arranged at the nearest waybridge. No payment shall be made forloading/unloading, stacking, transporation and waybridge charges etc.

Dismantling of laid paver tiles as directed by the engineer-in-charge. Scope of job includes properly removing of paver blocks of any thickness, special care tobe taken not to break the pavers and stacking them properly at a designated place within the premises as directed. Party to ensure joint measurement of thearea to be dismantled, alongwith EIC, before start. Payment shall be made basis the joint measurement, in absence of any joint measurement record, HPCLEIC decision shall be final. .

Dismantling of all types of roofing sheets like AC, GI, TRAC, etc. Scope of job includes handing over of all 'J', 'L' hooks, nuts and bolts or other joineries inproper bags..Party to ensure joint measurement of the job to be dismantled, alongwith EIC, before start. Payment shall be made basis the joint measurement,in absence of any joint measurement record HPCL EIC decision shall be final.

Dismantling of all types of ceilings except of bk work/CC, sheets like AC, TRAC, GYPSUM BOARD etc. Scope of job includes handing over of all 'J', 'L'hooks, nuts and bolts, suspendors or other joineries in proper bags. Party to ensure joint measurement of the job to be dismantled, alongwith EIC, before start.Payment shall be made basis the joint measurement, in absence of any joint measurement record HPCL EIC decision shall be final.

Excavation in RCC of any thickness by using pneumatic tools like Jack hammers, chisels or manually using hammers , chisels etc cutting the reinforcementsteel and stacking the same .The job also includes disposing the dismantled RCC within/outside HPCL premises to any unobjectionable place all complete asdirected by Engg.-In-Charge.

Excavation in PCC of any thickness by using pneumatic tools like Jack hammers, chisels or manually using hammers , chisels etc .The job also includesdisposing the dismantled PCC within/outside HPCL premises to any unobjectionable place all complete as directed by Engg.-In-Charge.

Loading / Unloading with countable stacking and transporting from one location to another, corporation supplied Engineering material ike CC paver blocks/ yard light poles/ signage/ steel plates etc of all sizes excluding tanks, DUs light fixtures. Rate includes all enroute taxes but excludes octroi, if any, on corporation material..


11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATE416 Detention charges Days 1100.00

417 0-50kms Lump Sum 1700.00418 Beyond 50kms Kilometers 18.00

419 0-50kms Lump Sum 3400.00420 Beyond 50kms Kilometers 32.00421 LOADING/UNLOADING OF MONO Dus Each 200.00

LOADING/UNLOADING OF MPD

422 Upto 1 No pump Each 2200.00423 Over & above 1 No. Each 180.00424 PVC PIPE 6",IS:4985, 6KG/SQCM Running

Metre 300.00

425 DOME TYPE CI GRATING Each 215.00

426 INSTL COMPRESSOR INCL. AVM PAD Each 1600.00

427 INSTL 15 KVA DG SET Each 2150.00

428 INSTALL DG PANEL Each 850.00

429 FIXING TYRE INFLATOR GAUGE Each 350.00Fixing tyre inflator gauge wall mounted model ELGI make with 5m hose including providing 50x50x6 angle post.

430 15 NB GI PIPE: CLASS C,IS1239 Running Metre 130.00

431 20 NB GI PIPE: CLASS C,IS1239 Running Metre 170.00

432 S/F MS BALL VALVE 15MM DIA Each 425.00Supply and fixing MS ball valve 15mm dia.

433 S/F SILICA GEL TRAP Each 1000.00

434 BRASS CHECK VALVE-40MM Each 1150.00

435 BRASS CHECK VALVE-50MM Each 1275.00

Transportation from one location to another, corporation supplied Mono pump / Dual pup / MPD / Air compressor / Light fixtures all other pumps etc in mini truck load upto 4MT (per trip load) . Rate includes all enroute taxes but excludes octroi if any on corporation material.

Transportation from one location to another, corporation supplied Mono pump / Dual pup / MPD / Air compressor / Light fixtures all other pumps etc in truck load upto 10 MT (per trip load) . Rate includes all enroute taxes but excludes octroi if any on corporation material..

Loading / Unloading in / from Mini truck / truck & stacking of mono / Dual pump / Air compressor with fittings upto 3HP / all other pumps upto 3HP.

Loading / Unloading in / from Mini truck / truck & stacking of MPD DU / All other compressor & pump with fittings above 3HP.

Providing and fixing 6" dia PVC pipes of 6 Kg/sqcm of Prince Make or equivalent make as per IS 4985 for rain water pipes including all fittings like bands , shoes etc., MS fabricated bracket as per requirement etc. All complete as directed by the Engg.-In-Charge.

Providing and fixing in position dome type rain water CI grating over PVC rain water pipes etc all complete.

Installation of HPCL supplied compressor including fixing of AVM pad.

installation of 15 KVA DG set on AVM pads including shifting from storage yard to DG room, all cable connection, installation of fuel tank, battery connection,etc. complete. Silencer pipe shall be paid separately.

Installation of DG panel including all cable connection.

Supply and laying 15 mm dia GI pipe conforming to IS 1239 heavy duty for compressed air service including bends, elbow, nipples, clamping @ 1 m c/c andon every bend using GI clamps and screws on wall etc. all complete.

Supply and laying 20 mm dia GI pipe conforming to IS 1239 heavy duty for compressed air service including bends, elbow, nipples, clamping @ 1 m c/c andon every bend using GI clamps and screws on wall etc. all complete.

SILICA GEL TRAP : Providing and fixing silica gel trap with virgin silica granules in 40 mm dia vent pipe all complete.

CHECK VALVE : Providing and fixing brass check valve of LEADER make on suction lines all complete .



11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATE436 PRECAST TRENCH:INT.300X500X350 Running

Metre 1875.00

437 PRECAST RCC TRENCH COVER Each 400.00

(B) DRIVEWAY WORKS

438 EXCAVATION IN EARTH<=3M Cubic Metres 100.00

439 EXCAVATION- HARD ROCK/PCC/RCC Cubic Metres 693.00

440 SAND FILLING - LAYERS<150MM Cubic Metres 400.00

441 EARTH FILLING - LAYERS< 200MM Cubic Metres 155.00

442 MURRUM FILLING - LAYERS<150MM Cubic Metres 295.00

443 GRANULAR SUBBASE -LAYERS<150MM Cubic Metres 280.00

444 PCC WORK-1:1.5:3 Cubic Metres 3699.00

PRECAST TRENCH : Supply and fixing of factory made precast RCC trench of internal size 300 x 500 x 350 ( W X L X H) and overall width 600 mm andheight 500 mm .The trench shall be of RCC M 35 grade with reinforcement of 8 mm dia @ 150 c/c both ways. The job includes excavation and preparation ofPCC base 1:3:6 150 mm thick all complete. The trench shall have interlocking arrangement for continuous fixing. Make - Surabh

PRECAST TRENCH COVER : Supply and fixing of factory made precast trench cover of internal size 450 x450 x75 ( W X L X Thickness) .The trench covershall be of RCC M 35 grade with suitable reinforcement. Make - Surabh, KK OR equivalent meeting the required specifications

EXCAVATION : Earth work in excavation in all kind of soil including soft rock, WBM, Brick soling, asphalt carpet but excluding hard rock, PCC and RCC,upto a depth of 1 m from the existing ground level. The job includes soring, shuttering, bailing out rain water / sub soil water manually or by using appropriatecapacity dewatering pump, ramming / rolling the bottom before laying any subbase, spreading, watering and compacting the excavated earth as directed byEngg.-In-Charge,

Disposal of surplus earth within / outside HPCL premises to any unobjectionable place all complete as per direction of Engg.-In-Charge.

EXCAVATION IN HARD ROCK / PCC / RCC Description same as item no.439 except the soil will be hard rock/ CC and the excavation should be carried outby pneumatic tools like jack hammer, chisels, or by blasting by using all safety precautions.

SAND FILLING Supply and filling with clean silver / river sand of approved quality in layers of 150 mm each including spreading, compacting by 8-10 Tonpower roller and watering etc, all complete as per direction of Engg.-In-Charge. Measurement basis compacted thickness only.

EARTH FILLING : Supplying and filling imported earth of approved quality in layers not exceeding compacted thickness of 200mm incl. Watering ,ramming,compacting, rolling, and re-rolling with 8-10 Ton power roller / mechanical compactors to achieve maximum compactness, all complete as per direction ofEngg.-In-Charge. The earth should be free from weeds, grass and other objectionable debris. Black Cotton soil shouldn't be used. Measurement basiscompacted thickness only.

MURRUM FILLING : Supplying and filling imported murrum of approved quality in layers not exceeding compacted thickness of 150 mm inclusive spreading,Watering ,ramming, compacting, rolling, and re-rolling with 8-10 Ton power roller / mechanical compactors to achieve maximum compactness, all complete asper direction of Engg.-In-Charge. The murrum should be excavated from a quarry / mines, free from weeds, grass and other objectionable debris.Measurement basis compacted thickness only.

Supplying, laying and filling granular sub-base with sand gravel mix in the proportion of 1:1 for a compacted thickness of 300mm in layers of 150mm thickusing approved quality gravel / stone aggregate and sand including watering, compacting with 8-10Ton roller to achieve maximum compactness.Measurement basis compacted thickness only.

Note: For all cutting/excavation and filling jobs, it will be the responsibility and duty of the contractor to take joint initial levels with Engg.-In-Charge in all casesbefore commencing the work. The joint levels should be certified by the contractor as well as HPCL Engg.-In-Charge. The payments will be made basis theinitial levels and final levels taken jointly and certified. The payment for all cutting / excavation will be made at the lower rate applicable for 0 to 3 m and thehigher rate will be paid only for the portion beyond 3 m depth. If the contractor fails to take jointly certified levels, the levels as taken by HPCL Engg.-In-Chargeshall be treated as final and all payments will be released basis the levels so taken by the HPCL Engg.-In-Charge.


11000038-HD-11370







449 RUBBLE SOLING – 230 MM Square Metres 163.00

450 RUBBLE SOLING – 150 MM Square Metres 127.00

451 WBM FIRST LAYER 100 MM Square Metres 92.00

452 WBM SECOND LAYER 75 MM Square Metres 81.00

453 WBM THIRD LAYER 75 MM Square Metres 76.00

454 BITUMINOUS MACADAM 75mm 60/70 Square Metres 413.00

455 BITUMINOUS MACADAM 75mm 80/100 Square Metres 466.00

PCC WORK : Providing and laying PCC using graded stone aggregate of using 20 mm and down size graded stone aggregates. The job includes machinemixing, providing formwork, MS/ plywood (minimum 19 mm thick) shuttering if directed by Engg.-In-Charge, placing, compacting by hand ramming , curing fora period of 14 days etc, all complete as per direction of Engg.-In-Charge. Removing of shuttering to be done carefully without such shock and vibration as todamage the PCC work.





Providing rubble soling including surface dressing, making required slope, soking the rubbles before laying, packing the gaps using small size rubble / stone /murrum, and hand ramming / using mechanical roller / compactor as per site requirement all complete.

Same as item no. 450 but for 150mm thick

WATER BOUND MACADAM (WBM) Providing and laying WBM in layers of 100 mm compacted thickness each using well graded stone aggregates of 40mm to 63 mm size of approved quality. Rate includes spreading metals, hand packing, filling the interstices with spalls, chips, and approved qualityMURRUM/STONE DUST as binder and rolling each layer with 10 Ton power roller with simultaneous watering till the metal is bound by the water binder pasteto achieve maximum compaction, finishing the surface to proper grade and level. First Layer 100 mm thick using 100 to 50mm size stone aggregate.

Rate also to include carrying out the following tests on aggregates and test result to be submitted to Engg.-In-Charge before use and shall meet the followingstrength requirements. LA Abrasion value = 40%, Flakiness index = 15%.

Second Layer 75 mm thick using 63 to 40mm size stone aggregate

Third layer of 75mm thick using 53 to 22.2 mm size stone aggregate.

BITUMINOUS MACADAM 75mm THICK USING 60/70 GRADE BITUMEN: Providing and laying premix bituminous macadam base course with good qualitystone aggregate mix as follow 20mm = 30%, 12mm=35%,6mm=15% coarse sand 15 % and bitumen 60/70 grade 6% by weight .The aggregate shall be ofquality size and grading as specified and bitumen shall be straight run bitumen of grade 60/70 @ 6 % by weight of total mix . The job includes hot mixing byusing mini hot mix plant , transporting mix material and laying the same to the required level & grade, rolling with power roller of 8 to 10 Ton capacity to achieverequired compaction and density all material , labour etc. complete. The macadam course shall be laid in two layers of around equal thickness, eachlayer shall be rolled and compacted. Tack coat shall be applied between the two layers@ 9.8 kg per 10 sqm.


11000038-HD-11370



456 SEMI DENSE BITUMIN. CONCR.25mm Square Metres 196.00

457 SEMI DENSE BITUMIN. CONCR.40mm Square Metres 327.00

458 MASTIC WEARING COARSE 25MM Square Metres 399.00

459 RCC D/W1:1.5:3 VACUUM DEWATER. Cubic Metres 4626.00

460 RCC D/W READYMIX M20 Cubic Metres 3680.00

BITUMINOUS MACADAM 75 mm THICK USING 80/100 GRADE BITUMEN: Providing and laying base course with bituminous macadam of compactedthickness 75 mm using 20 to 50 mm size graded approved quality stone aggregates, using bitumen grade 80/100 at 5% by weight of mix including hot mixingof aggregates and mixing of aggregates and bitumen in hot mix plant, transporting and laying mixed material with paved finisher to proper camber and gradient, rolling the surface with road roller of 8-10 Ton capacity to achieve required compaction all including applying a priming coat with bitumen grade 80/100 @1kg/sqm over the already laid water bound macadam surface, all complete as specified. Job including cleaning the bottom surface on which the asphalt haveto laid. Providing tack coat using 80/100 asphalt @ 9.8 kg./10 SQM. area prior to laying asphalt carpet. ( Hot molten asphalt to be mixed with aggregates (66% of 12 to 20 mm size and 34% of 6 to 12 mm size graded crushed stone aggregates) @ 56 Kg./CUM of aggregates). BROKEN SAND STONE SHALLNOT BE USED AS AGGREGATES.

The macadam course shall be laid in two layers of around equal thickness, each layer shall be rolled and compacted. Tack coat shall be appliedbetween the two layers@ 9.8 kg per 10 sqm.

SEMI DENSE BITUMINOUS CONCRETE (25 mm Thick) : Providing and laying 25 mm thick semi dense bituminous concrete on prepared surface with goodquality graded stone aggregate as per following requirement -Material 5euired per 100 Square meter Crushed stone aggregate of 13.2 mm size = 1.0 CUM ,11.2 mm size -1.6 CUM , Fine aggregate 6 mm size - 1.1 CUM Bitumen 60/70 grade including tack coat = 330 Kg .The job includes hot mixing of aggregateand bitumen by using hot mix plant transportation mixed material and laying the same , rolling with 8 to 10 Ton power roller to uniform consolidated compactedthickness of 25 mm over a tack coat of 2.0 Kg per 10 Square meter to achieve the required level and grade all material, labour etc complete.

SEMI DENSE BITUMINOUS CONCRETE (40 mm Thick) : Providing and laying 40 mm thick semi dense bituminous concrete on prepared surface with goodquality graded stone aggregate as per following requirement: Material per 100 Square meter Area - Crushed stone aggregate of 13.2 mm size = 1.60 CUM;11.2 mm size -2.56 CUM; Fine aggregate 6 mm size - 1.76 CUM; Bitumen 60/70 grade including tack coat = 525 Kg .The job includes hot mixing ofaggregate and bitumen by using hot mix plant transportation mixed material and laying the same , rolling with 8 to 10 Ton power roller to uniform consolidatedcompacted thickness of 40 mm over a tack coat of 2.0 Kg per 10 Square meter to achieve the required level and grade all material , labour etc complete .

MASTIC WEARING COARSE (25 mm Thick): Providing and laying 25 mm thick mastic wearing coarse using stone aggregates as per following specs-Coarse aggregated to be used 35% of total mix , Balance shall be coarse sand and filler material, Lime stone powder and industrial bitumen of grade85/25confirming to IS 702 prepared by using Mastic cooker and laid to required level and slope including providing anti skid surface with bitumen precoated finegrain chipping of 9.5 mm to 13.2 mm size at the rate of 0.005 CUM per 10 square meter of approx. spacing of 10 cm center to center in both directions ,pressed into surface protruding 1mm to 4 mm over mastic surface including cleaning the surface removal of debris etc. material and labour complete. NOTE :Lime stone powder shall have minimum calcium carbonate content of 80 %.

Providing and laying 200mm thick RCC driveway with 1:1.5:3 nominal mix using 20mm and down size crushed stone aggregates in panels using MSchannel shuttering, machine mixing, vibrating with screed board vibrator, laid in blocks size as directed by Engg.-In-Charge, cutting the joints by diamondblade saw and filling gaps with hardening compound, pond curing for 14 days, vacuum dewatering, finished with power trowelling. Concreting shall be carriedout as per IS 456:2000 Latest Edition. The layout plan of proposed RCC driveway shall be divided into suitable panels of size as directed by Engg.-In-Chargeand complete plan for panelwise casting/grooving/cutting shall be submitted to Engg.-In-Charge for his approval. Concreting shall not commence without suchapproval.

Rate shall also include providing approved quality minimum 20micron thick polythene paper below the driveway, hardener as per manufacturer'srecommendation for heavy traffic driveway adding plasticiser as per manufacturer recommendation, of Roffe / CICO equivalent approved make. Job alsoincludes constructing horizontal and longitudinal vatas with 1:10 CM for curing, leveling depressions if any in the base with 20mm stone aggregates andcoarse sand.Proper slope to be provided in driveway for easy draining of rain water. Reduced level of the driveway area to be taken jointly with architect beforecommencement of concreting and after concreting and the thickness of RCC to be checked. Testing of cube, reinforcement steel, stone aggregates, sand,cement etc. to be carried out by contractor at no extra cost. Tubing, ducting, trenching and other necessary embedded items in concrete shall be checked with architect / HPCL representative before concreting.

Same as above item no.460 but using M20 grade ready mix


11000038-HD-11370


TL. NO. DESCRIPTION UNIT RATE461 D/W1:1.5:3WITHOUT VACU. DEWAT. Cubic

Metres 4071.00

462 REINFORCEMENT STEEL IS1786 Metric Ton 42000.00

463 THERMOPLASTIC ROAD MARKING Square Metres 395.00

464 RAISED PAVEMENT MARKERS Each 415.00

465 LINEAR DELINEATION SHEETING Each 3525.00

466 MASTERTOP 1332 Square Metres 2700.00

467 PREMIX CARPET-50 MM Square Metres 303.00

468 PREMIX CARPET-100 MM Square Metres 560.00

Supply ,fabrication, hoisting and placing in position HYSD reinforcement bars conforming to IS1786 -Latest Edition Grade FE 415 /TMT bars of same gradeas per detailed drawing and specifications including cutting, bending, cranking and tying with 18 SWG black annealed binding wire complete. The rates shallbe applicable for all heights and depths. Payment shall be made as per reinforcement drawings and with theoretical weights only including all authorised laps,chairs, spacers and hooks.

Providing and fixing 3M make adhesive type heavy duty high performance raised pavement markers with shanks (Glow Stubs) made of Engineering Polymerin size 101x89mm with height 20mm having retroreflective element on both sides and to be fixed on cement concrete rigid pavement with adhesive/shanks asrecommended by manufacturer and interspacing as per Engg.-in-Charge approval. Rate includes necessary before/after cleaning, tools and tackles etc. allcomplete

Providing and fixing 3M make Linear Delineation Sheeting (LDS) comprising of panels of size 4" wide and 33" length in yellow colour. The panel is to beconstructed of cube corner Retro Reflective Material bonded to Aluminium substrate with memmed lateral edges. The panel assembly shall have a repeatingraised lateral ridge every 2.25 inch, 0.34 inch in height. The typical retro reflective values at 88.5 degree entrance angle / 0.2 degree observation angle to be270, 162, 11080 (candelas/ meter square / lux) of yellow colour.

The fitting will be done on brick masonry/concrete walls as per manufacturer specified procedures and approved nails/fixtures in line and level as per advice ofEngg.-in-Charge (EIC). Powder coated MS angle edge protection shall be provided to make it theft resistant. Measurement and payment shall for per no. of33inch long and 4" wide LDS provided as per EIC advice.

Supplying, painting/laying Degussa make Polyurethane based multi – component decking system for heavy abraison areas including material, machinery,tools and tackles, power etc. all complete following manufacturer specified procedures. The brief of constituent layers/coats are as following, the last being thetopmost layer: Mastertop 1332MTOP 1200 plus primer @ 0.3 kg / sqm; Mastertop SRA No. 3 sand scatter @ 0.6 kg/sqm; Mastertop Membrane 23 @ 0.5 kg/sqm; Mastertop SRA No. 3sand scatter @ 1 kg/sqm and TWO COATS of Mastertop TC 458 of colour French/HP blue (Colour Code BS 166) @ 0.4 kg / sqm each coat i.e. total0.8kg/sqm. Each layer will be given generally one day set period as per manufacturer's specifications. Traffic will not be allowed in the area from very first layerapplication till setting of top coat. It shall be vendor's responsibility to ensure that proper application for each layer is done with sufficient time. In case thevendor fails in ensuring proper application and setting time, rectifications shall be done without extra cost as per manufacturer specified procedures and asagreed by Engg.-in-Charge in writing.

The vendor shall furnish 5 years repalcement guarantee on Rs.100/- stamp paper against defects, damage under vehicular traffic, wear and tear etc. fromthe completion date. HPCL descrition shall be final and binding on the vendor.

Providing and laying premix carpet 50 mm thick ( Consolidated) with coarse aggregate of nominal size 12.5 mm ( two part ) and 10 mm ( one part) . Quantityof bitumen (80/100 grade) used should be 36.5 Kg per 10 sqm for premix and 7.5 kg per 10 sqm for tack coat. Surface preparation by cleaning with wirebrush, removing the dust etc before applying tack coat. The job includes compaction by 8 to 10 Ton roller to proper camber and slope all complete as perdirection of Engg.-In-Charge.

Same as above item no. 460 but without, providing hardener at top, mixing plasticizer, vacuum dewatering and power trowelling with 1:1.5:3 nominal mix.

Supplying and applying Berger make Sigmark thermoplastic road marking paint as per MORTH specifications 803.4. The work shall be carried out strictly inline with maufacturer's procedures and using specified materials, tools, heating device/apparatus and machinery etc. all complete. The briefs of materials areas following:(i) Hot Melt Thermoplatic Road Marking Compound: 5 kg/sqm(ii) Glass Beads: 250 gm /sqm

The drying time should be within 5 minutes and dry coat thickness to be 2.5 mm.Rate shall be inclusive of all material, labour, tools & tackles, power, heating apparatus etc. all complete. Work shall be carried out ensuring safety at outletand as per approved drawing and plan.


11000038-HD-11370



469 SEAL COAT 12 MM Square Metres 125.00

470RELAYING OF PAVERS

Square Metres 45.00

471 S/L DRIVEWAY PAVERS-80MM Square Metres 572.00

472 S/L GRASS PAVERS MIX M-40 Square Metres 473.00

473 S/L PEDESTRIAN PAVERS MIX M-35 Square Metres 484.00

Specifications same as item no. 472 but for 60 mm thick pavers blocks of M 35 grade as per IS-15658 ; 2006, in 1 red and 2 grey combination for walkwaysand light load areas as advised by EIC .

100mm thick carpet : Specification same as above item no. 468 but two layers of 50mm thick each.

Providing and laying seal coat of 12 mm thick with 6.3 mm down coarse aggregate. Quantity of bitumen used should be 19.6 Kg per 10 square meter of sealcoat . The job includes compaction by 8 to 10 Ton power roller to proper camber and slope all complete as per direction of Engg.-In-Charge. Finishing shouldbe done by applying a layer of sand in order to fill up the voids.

NOTE : All the asphalting jobs shall be started only after sta cking bitumen at the site as per theoretical calculation con sidering the area. Thetotal job including seal coat to be carried out in one go. In ca se of any delay in laying the seal coat after laying the premix carpet, additionaltack coat @ 5.0 Kg per 10 sqm to be laid without an y extra payment.

Laying of HPCL supplied pavers in line and level , as per attached specifications. The job includes supplying and laying sand bedding, compacting using plate vibrator, all material and labour complete. Pavers will be laid at 45 degree to road line in 1 red and 2 grey arrangement. Plan of laying will be developed by the contractor and prior approval of EIC will be taken before commencement of laying..

Supply and laying of 80mm thick grey / coloured pavers in line and level and approved pattern and shape, as per attached specifications. The job includessupplying and laying sand bedding, compacting using plate vibrator, all material and labour complete. Pavers will be laid at 45 degree to road line in 1 red and2 grey arrangement. Plan of laying will be developed by the contractor and prior approval of EIC will be taken before commencement of laying. The paverssupplied should qualify min comp. strength of 47.2MPa and should conform to IS:15658:2006. The party shall have to produce manufacturer's certification onthe paver qualifying criteria stated in IS-15658 and limits specified in the attached specification before the pavers are sited. HPCL reserves the right to dorandom sampling and testing as per IS-15658:2006 to assess manufacturer's certification on qualifying norms specified in the attached specification. Thetesting charges, if samples qualify, shall be borne by HPCL, else shall be borne by the party.

Specifications same as item no. 472 but for grass pavers. Grass pavers shall be of 80 mm thickness and shape corner-cut square made out of 500x500 mmsize with all the four corners cut in quarter size circles of 125 mm radius. Four nos. of such pieces laid in symmetrical square pattern will give total openingarea of 0.196 sqm. The circular openings so formed shall be planted with grass. Supply and laying of grass is not included in the scope but filling of theseopenings with same sand fully compacted and vibrated is included in the scope.


schedule of rates - valid for rajasthan state...

Documents