SCENARIOS S2S MANUALSCENARIOS EXECUTIVE

L E G S + PA N E L

Side view - Slot in end leg from side of the panel,attach connection plate at the side of the endleg.

Side view - Slot in end leg from side of the cabinet,attach connection plate at the side of the endleg.

Bottom view - Attach end leg into cabinet, fix self tap screws by following a to c.

Attach the removable cover to close the panel. Complete look for panel leg.

Bottom view - Attach end leg into panel, fix self tap screws by following a to c.

1

1 2

3 4

2

1

S C E N A R I O S S 2 S M A N U A L S C E N A R I O S E X E C U T I V E

M6 x 8m

m

Cap Screw

x 2Allen Key

5mmSelf Tap Screw x 6

a.

b.c.

L E G + C A B I N E T

M6 x 8m

m

Cap Screw

x 2Self Tap Screw x 6

a.

b.c.

L E G + C A B I N E T

2

S C E N A R I O S S 2 S M A N U A L S C E N A R I O S E X E C U T I V E

Attach the removable cover to close the panel. Complete look for cabinet leg.

3 4

F R A M E

x-beam - Mount x-beam to the end leg.

x-beam - Complete look for x-beam Hexagon rod - Slot in a.hexagon outside to the middle top of end leg, b. slot in hexagon stopper for both end legs

x-beam - Mount x-beam to the another end leg.

1

3 4

2

a.b.

3

Hexagon rod - Slot in hexagon inside to hexagon outside with the same distance for another end leg.

Hexagon rod - Hook cable tray on x-beam. Complete look for cable tray.

Hexagon rod - Slot in hexagon inside to hexagon outside with the same distance for another end leg.

Hexagon rod - Hexagon inside should be stop athexagon stopper for both end leg.

Complete look for hexagon rod.

5

1 2

7

6

8

S C E N A R I O S S 2 S M A N U A L S C E N A R I O S E X E C U T I V E

F R A M E

Top view of hexagon rod

C A B L E M A N A G E M E N T

4

S C E N A R I O S S 2 S M A N U A L S C E N A R I O S E X E C U T I V E

W O R K T O P

Place worktop on frame.

Tighten x-beam with set screws for both side of top supports.

Tighten hexagon stoppers on both side.

Side view - Attach worktop with JCBC screws frombottom of top support for both end legs.

1

1 2

2

M8 x 16m

m

JCBC Screw

x 8Allen Key

5mm

F I X I N G

Allen Key 4mm

Allen Key 2mm

5

S C E N A R I O S S 2 S M A N U A L S C E N A R I O S E X E C U T I V E

S TA B I L I Z AT I O N B A R

Attach stabilization bar on side of the leg.

Attach L-bracket with JCBC screws on the holesfor left & right side of melamine modesty panel.

Complete look for Scenarios Executive desk.

Attach melamine modesty panel to worktop.

Place in plastic cap cover on both side of it.

1

1

3

2

2

Allen Key 5mm

M6 x 10m

m

Cap Screw

x 2

M O D E S T Y PA N E L

Allen Key 4mm

Allen Key 5mm

M6 x 16m

m

M8 x 16m

m

JCBC Screw

x 12JCBC Screw

x 8

6

S C E N A R I O S S 2 S M A N U A L S C E N A R I O S E X E C U T I V E

C O N T R O L B O X

Bottom view - Attach control panel with S/D screws at the bottom of the worktop.

Place control box in cabletray, tidy up all the cables into the cabletray.

1 2

M3 x 13m

m

S/D Screw

x 4

Attention:Before starting the system, please make sure, that the operating voltage of the system conforms with the local power supply. The mains plug of the control has to be connected to a free accessible power supply.

* PLUG IN - FOLLOW THE INSTRUCTION BELOW.

B A C K V I E WF R O N T V I E W

H S

M IM 2

D R I V E 1

D I S P L AY

D R I V E 2

7

S C E N A R I O S S 2 S M A N U A L S C E N A R I O S E X E C U T I V E

S E T T I N G

1

S

2 3 4

Display

Store memory Handset

Memory 1,2,3,4 Up Down

---000

0001

S

2 3 4

DisplayMemory 1,2,3,4

S 1

Press and hold the down button until the lowest position 068 is reached (show in display, stop flashing), system is ready for further programming,the maximum reachable height is 118.

1

S

2 3 4

Handset = 68 - 118cmH

Up

068

1

S

2 3 4

Up Down

0701

S

2 3 4

Display Up Down

068

Store memory

Memory 1,2,3,4

1

S

2 3 4000

Store memory

S -

Start up - Turn on the main power supply before setting. Once the power is on, display flashes show 000 or ---.

1 2

Normal operation - Press and hold up or down until the desired height of the desk has been reached, the display always shows the actual height.

Move to the desired desk height. Press the store memory ‘S’. You will see the display shows ‘S - ‘.

Press one of the memory keys, 1,2,3,4, and the num-ber of the position height is displayed, a double click is heard at the end of memory saved. Repeat the same step of this for other preferred heights.

Saving preferred height - 4 preferred heights can be saved.

3

5 6

4

S C E N A R I O S S 2 S M A N U A L S C E N A R I O S E X E C U T I V E

S E T T I N G

P L E A S E R E F E R T O M A R K A N T

MOTOR CONNECTOR SET USER MANUAL FOR

HEIGHT ADJUSTABLE DESK

F O R F U R T H E R H E L P

1

S

2 3 4068

Memory 1,2,3,4

Moving to a saved preferred height - Press and hold one of the keys, 1, 2, 3, 4, the desk will moves towards to the preferred height.

7

8