savant keypad link (skl-4000) quick reference guide qrgs/skl-4000... · the savant® keypad link...
TRANSCRIPT
The Savant® Keypad Link (SKL-4000) Quick Reference Guide provides the information necessary to install the SKL-4000. Each SKL-4000 connects up to 40 Savant keypads to any Savant SmartLighting controller with available RS-422 ports. Do not put more than 20 stations on a single homerun. Several homeruns are preferable to one long homerun and can easily be tied together at the controller. A total of 256 keypads may be connected to a Savant SmartLighting controller through multiple SKL-4000s. Double ganged keypads are considered two keypads.
Box Contents(1) SKL-4000 (1) Quick Reference Guide (this document)
Required System ComponentsSavant controller with an allocated RS-422 connector• SSL-P002• SSL-P018Savant Keypads: Up to 40 supported per SKL-4000 Station Bus Cabling• 100 ft/30.48 meters (CBL-4100)• 250 ft/76.20 meters (CBL-4250)• 500 ft/152.40 meters (CBL-4500)• 1000 ft/304.8 meters (CBL-41000)
Specifications
EnvironmentalEnvironmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Dimensions and WeightDimensions and Weight
Height 12.17 in/309.07 mm
Width 15.48 in/393.19 mm
Depth2.71 in/68.81 mm (depth into wall without front panel)
Depth2.81 in/71.37 mm (overall depth with front panel attached)
Weight 8.75lb/3.97kg
PowerPower
Input 120-240V AC, 50/60 Hz
Power Supply Output to Station Bus
16 - 24V DCPower Supply Output to Station Bus 120 watts 5 Amps
CableCable
Keypad/station16 AWG (recommended) 1000 ft (300 meters), cumulative
Keypad/station18 AWG 330 ft (100 meters), cumulative
ComplianceCompliance
Safety and Emissions FCC Part 15 | UL | CE Mark | C-Tick
RoHS Compliant
Front View with Vents
Important Front cover needs to be installed when SKL-4000 is operational.
2 3
5 6
41
SKL-4000 Interior Panel
1 RS-422 In Port Type: RJ-45Connects to Savant SmartLighting Controller: SSL-P002 or SSL-P018Port Type: RJ-45Connects to Savant SmartLighting Controller: SSL-P002 or SSL-P018
2 RS-422 Out Port Type: RJ-45Connects to additional SKL-4000sPort Type: RJ-45Connects to additional SKL-4000s
3 LEDs
StatusRED flashing indicates station bus (data) to or from keypads.Solid RED indicates overload.Off indicates no data traffic.
3 LEDsRX
RED flashing indicates serial traffic.Solid RED indicates overload.Off indicates no serial traffic.3 LEDs
TXRed flashing indicates station bus (data) to or from keypads.Solid RED indicates overload.Off indicates no data traffic.
3 LEDs
PWR GREEN indicates power is connected.Off indicates power has been disconnected.
4 Address Dial Settings range from 0-F to support up to eight SKL-4000 units.Settings range from 0-F to support up to eight SKL-4000 units.
5 Connectors1 - 4
3-pin, screw-type, removable plug-in connectors used to connect to station (keypad) bus3-pin, screw-type, removable plug-in connectors used to connect to station (keypad) bus
6 STATION ADDRESS Information labels to identify location of keypads and zones.Information labels to identify location of keypads and zones.
Savant Keypad Link(SKL-4000)
Quick Reference Guide
009-0670-00SKL-4000-00
101912
Copyright © 2012 Savant Systems, LLC. SAVANT and RacePoint Blueprint are trademarks of Savant Systems, LLC.All brand names, product names and trademarks are the property of their respective owners. Savant Systems, LLC reserves the right to change product specifications without notice.
SKL-4000 Interior Panel with Station Bus and Module cabling
SKL-4000 showing high voltage cabling
Wiring the Savant Keypads to the Savant Keypad LinkTo connect the keypads to the SKL-4000, the wires from the 3-pin connectors must be spliced with the 3-wire cable running to the keypad backboxes. The next figure shows the use of 16-gauge (AWG) wire, but in shorter installations (up to 330 feet) 18-gauge wire can be used. Crimp connectors or wire nuts can be used to terminate the stranded wire. Crimp connectors are preferred.
Control Station Backbox Control Station Backbox Control Station Backbox
3 PINCONNECTOR
3 PINCONNECTOR
LiteTouch Control Station Wire 5 ea. 18 ga. Wires
White Spare Wire 16 ga. Spare WireBlue 16 ga. (D)Black 16 ga. (–)Red 16 ga. (+)
18 ga. Blue Connector
18 ga. Red Connector
Twist pair together forconnection to blackground connector
NOTE: Voltage readings at this end should typicallyread 1 or 2 volts less than at the CCU end.
Use crimpconnectors or
wirenuts.(Crimp connectors are preferred.)
Keep the control station in its protective plastic bag until all construction work is completed.Control Station Backbox Control Station Backbox Control Station Backbox
3 PINCONNECTOR
3 PINCONNECTOR
LiteTouch Control Station Wire 5 ea. 18 ga. Wires
White Spare Wire 16 ga. Spare WireBlue 16 ga. (D)Black 16 ga. (–)Red 16 ga. (+)
18 ga. Blue Connector
18 ga. Red Connector
Twist pair together forconnection to blackground connector
NOTE: Voltage readings at this end should typicallyread 1 or 2 volts less than at the CCU end.
Use crimpconnectors or
wirenuts.(Crimp connectors are preferred.)
Keep the control station in its protective plastic bag until all construction work is completed.
Savant SmartLighting Station Bus Wire for Keypad Connection
Control Station Backbox Control Station Backbox Control Station Backbox
3 PINCONNECTOR
3 PINCONNECTOR
LiteTouch Control Station Wire 5 ea. 18 ga. Wires
White Spare Wire 16 ga. Spare WireBlue 16 ga. (D)Black 16 ga. (–)Red 16 ga. (+)
18 ga. Blue Connector
18 ga. Red Connector
Twist pair together forconnection to blackground connector
NOTE: Voltage readings at this end should typicallyread 1 or 2 volts less than at the CCU end.
Use crimpconnectors or
wirenuts.(Crimp connectors are preferred.)
Keep the control station in its protective plastic bag until all construction work is completed.Control Station Backbox Control Station Backbox Control Station Backbox
3 PINCONNECTOR
3 PINCONNECTOR
LiteTouch Control Station Wire 5 ea. 18 ga. Wires
White Spare Wire 16 ga. Spare WireBlue 16 ga. (D)Black 16 ga. (–)Red 16 ga. (+)
18 ga. Blue Connector
18 ga. Red Connector
Twist pair together forconnection to blackground connector
NOTE: Voltage readings at this end should typicallyread 1 or 2 volts less than at the CCU end.
Use crimpconnectors or
wirenuts.(Crimp connectors are preferred.)
Keep the control station in its protective plastic bag until all construction work is completed.
Keypad Backbox
Note: Voltage readings at the end closest to the 3-pin connector should typically read no more than 1 or 2 volts less than at the Savant Keypad Link end.
Keypad backboxes should have a minimum inside dimension of 3 in. high x 1⅞ in. wide x 1½ in deep. Use a square-cornered backbox to best accommodate these dimensions. Do not use plastic rings with rounded corners—keypads, especially multiple-gang keypads, will not fit. Single-gang, metal cut-in boxes, plaster, or tile rings are not acceptable.
In new construction installations, for example, a single gang backbox, model P-241 (supplied by Allied Moulded Products) would accommodate a Savant keypad. An example of a double gang backbox is model P-442 (supplied by Allied Moulded Products).
Whether installing backboxes in new construction or “old work” installations, the installer should test fit the keypad to the backbox before installing the backbox in a wall.
Note: Keypads may be wired to a homerun device, not to exceed 1000 feet with 16 AWG or 330 feet with 18 AWG.
SKL-4000 Mounting InstallationTo recess- mount:1. Mount SKL-4000 to wall studs using screw holes located on the side panels of the
enclosure.2. Leave 3 inches minimum space between each SKL-4000 to accommodate the lids .3. Install all SKL-4000s before connecting the power.
To surface mount:1. Mount SKL-4000 to wall using screw holes located on the back panel of the enclosure.2. Install all SKL-4000s before connecting the power.
Additional Documentation
Additional Documentation for the SKL-4000 is available at: SavantSystems.comProducts > • Savant Lighting Control
Savant Keypad Link(SKL-4000)
Quick Reference Guide
009-0670-00SKL-4000-00
101912
Copyright © 2012 Savant Systems, LLC. SAVANT and RacePoint Blueprint are trademarks of Savant Systems, LLC.All brand names, product names and trademarks are the property of their respective owners. Savant Systems, LLC reserves the right to change product specifications without notice.