sapphire - cubicles.cc · connect the frames by m8*30 bolt sapphire cubicle system 3! same height...
TRANSCRIPT
Fix the side groove into wall
1
1
SAPPHIREC U B I C L E S Y S T E M
1
Wall StarterTrack
Installing Wall Starter
40mm adjus table depth
A AInsert the side pole to the side groove.Side pole is processed as photo and fixed with panel connectors.
mill away 50mm
Wall Starter
Step2
5mm
SAPPHIREC U B I C L E S Y S T E M
Use M8*40 bolt to connectside pole and frame
2
Step1Adjust the adjuster 5mm upto keep space for adjustmentin the further assembling.
Leveler
*Make sure it’s level
Leveling and Connecting Your 1st Panel to a Wall Starter
1. Adjust all frames into same level
2. Connect the frames by M8*30 bolt
SAPPHIREC U B I C L E S Y S T E M
3
!sameheight
Top Track
Connect the partition and column by M8*20mm bolt
120 degree2 ways connection
120 degree3 ways connection
SAPPHIREC U B I C L E S Y S T E M
4
4 ways connection 3 ways connection 2 ways connection
*All connectors simply bolt into panels.
Straight Connector
L
L
90
SAPPHIREC U B I C L E S Y S T E M
Installing SwingingDoor Frame
5
Door Frame withPartition Frame
Door Frame withSide Pole
Fix the L-ShapeAluminum Bracket
How to Fix the Door Frame:1. Fix the door frame material (45° cutting) with enhanced pole.2. Fix the left and right door frame material with partition frame with screws in through the panels into the door frame. (Tiles should be off one side to screw in)3. Fix the top door frame material with L brackets, and insert it to the left and right door frame material.4. Fix the partition frame above the door to the left and right partition frames.5. Fix the hinges and sealings.
Screw in through the panelinto the door frame
1
2
3
4
5
SAPPHIREC U B I C L E S Y S T E M
5
Door Frame Assembly
1.TOP
SIDES
FILL
ER
FILLER
Arrange Door Frame pieces on the floor in the correct positions that they will beput togther.
2.A. Screw in Top piece to side piecesusing 1” screws (not self tapping).B. Then insert Fillers into sides with grooveside up.
A.
B.
3. Insert Door Frame
6
90 L
L
SAPPHIREC U B I C L E S Y S T E M
7
Door Frame Assembly
4. Make sure Door Frame is level
5.While tiles are off on 1 side of the wall, screw in through the panel to the frame with 1 1/2” self tapping screws. (7ft H walls this is the final step for the door frame assembly. 8ft H wallsneed to be screwed in from the top as well.)
7ft
8ft
*
*Only screw door frame in from top if setup is 8ft High
SAPPHIREC U B I C L E S Y S T E M
8
Swing Door Lock Assembly
How to define door orientation
Left Open Door Right Open Door
Assembly Step One
Assembly Step Two Assembly Step Three
screw
lock body
door body
1
23buckle groove
lock buckle
screw
SAPPHIREC U B I C L E S Y S T E M
10
Top Groove Panel Stabilizer*May sometimes be needed to cut to size.
1 1/2” Sheet Metal Screws
1 1/2” Sheet Metal Screws
83 3/8”
2 1/2”
7’H Custom Panel
84 11/16”(with top cap)
SAPPHIREC U B I C L E S Y S T E M
11
Sliding Door Assembly
AB
BA
B
C
C
Place Sliding Door Rail ontoscrewed in Sliding Door Rail Clipsand screw in from below. Door Railmust be placed 83 3/4” from the ground.
D
D
E
1.2.
3.After inserting the SlidingDoor into the rail, Secure Stopperon the end.
4.
Place Sliding Door Rail Finish Cap(s).
E
5.
Place Sliding Door Bottom Trackon floor using double sided tape,velcro, or glue; Lining it up with the Door Rail. Then proceed to place in Sliding Door.
Parts:
Screw in Sliding Door Track Clipsinto grooves between panels.(Door Rail must be placed 83 3/4”from the ground measuring from the bottom of the rail to the ground.)
83 3/4”83 3/4”