s p inline 1-1/2˝ m u circulator pumps p r o t a l u c r i c 2 1 e … · a gorman-rupp company...
TRANSCRIPT
AMT Inline Circulator Pumps are designed for continuousduty industrial/commercial systems. Pumps are availablein a variety of material configurations to meet yourspecifications. Pumps are powered by a 56C NEMA TotallyEnclosed Fan Cooled (TEFC) frame electric motor with 1/2"conduit connection. Pumps are interchangeable with othermanufacturers.
* Maximum temperature applies to water only.
INLI
NE
1-1/
2" C
IRCU
LATO
R PU
MPS
HVM-9
Inline 1-1/2˝Circulator Pumps• Cast Iron or Silicon BronzeConstruction with Silicon Bronze Impeller
• EPDM/EPR Mechanical Seal andCasing O-Ring Standard, Viton® Option Available
• Includes Mounting Flange Kit for 1-1/2˝ NPT
• Special Flange Designed to Accept B&G Flange or Standard 150lb 4-Bolt Flange
• Maximum Water Temperature 225° F (107° C)*
• Maximum Flow 130 GPM
• Maximum Head 53 Ft. (23 PSI)
• 1/8˝ NPT Seal Wash/Vent Port
• Single Phase or Three Phase TEFC 56C Motor
5860-95 Cast IronCirculator Pump
®
A Gorman-Rupp Company
400 Spring Street • Royersford, PA 19468 USA
www.amtpump.com • 888-amt-pump (268-7867)For use with nonflammable liquids compatible with pump component materials. Viton® and Teflon® are registered trademarks of E. I. Dupont.
0
01
02
03
04
05
06
07
08
09
001
011
021
031
041
051
061
071
0
2
4
6
8
01
21
41
61
81
02
22
42
62
82
03
23
43
0410310210110010908070605040302010
RHSPN
FS 00.1
FS 51.1
pmup etarepo TON oDaera yarg siht ni
)zH 06( MPR 5271 @ yticapaC0.1 ytivarg cificeps retaW- diuqiL 13.2 yb edivid ,isp ot trevnoC)*(
]Wk 52.0[ PH 3/1 seireS 685 = A]Wk 73.0[ PH 2/1 seireS 685 = B]Wk 65.0[ PH 4/3 seireS 685 = C
]*.tf[ ]m[
]mpg .S.U[
To
tal H
ead
m[ 3 ]h/
C
B
A
035202510150
0
1
2
3
4
5
6
7
8
9
01
NP
SH
R
]m[ ]*.tf[
02468
Performance of 1½" Inline Circulator Pumps
0010203040506070809
001011021031041051061071081091002012022
02468012141618102224262820323436383042444
0410310210110010908070605040302010
RHSPN
FS 00.1
pmup etarepo TON oDaera yarg siht ni
FS 51.1
)zH 06( MPR 5271 @ yticapaC0.1 ytivarg cificeps retaW- diuqiL 13.2 yb edivid ,isp ot trevnoC)*(
]Wk 65.0[ PH 4/3 seireS 785 = D]Wk 57.0[ PH 1 seireS 785 = E
]Wk 21.1[ PH ½1 seireS 785 = F
]*.tf[ ]m[
]mpg .S.U[
To
tal H
ead
m[ 3 ]h/
FE
D
035202510150
0
1
2
3
4
5
6
7
8
9
01
11
21
31
NP
SH
R
]m[ ]*.tf[
0
5
01
Performance of 1½" Inline Circulator Pumps
0
01
02
03
04
05
06
07
08
09
001
011
021
031
041
051
0
4
8
21
61
02
42
82
23
63
04
44
84
25
65
06
0410310210110010908070605040302010
RHSPN
FS 00.1
pmup etarepo TON oDaera yarg siht ni
FS 51.1
G
)zH 06( MPR 5271 @ yticapaC0.1 ytivarg cificeps retaW- diuqiL 13.2 yb edivid ,isp ot trevnoC)*(
]Wk 65.0[ PH 4/3 seireS 885 = G]Wk 57.0[ PH 1 seireS 885 = H]Wk 21.1[ PH ½1 seireS 885 = I
]Wk 94.1[ PH 2 seireS 885 = J
]*.tf[ ]m[
]mpg .S.U[
To
tal H
ead
m[ 3 ]h/
J
I
H
035202510150
0123456789011121314151617181
NP
SH
R
]m[ ]*.tf[
0
5
01
Performance of 1½" Inline Circulator Pumps
®
A Gorman-Rupp Company
Manufacturer of AMT & IPT Pumps400 Spring Street • Royersford, PA 19468 USA
www.amtpump.com • 888-amt-pump (268-7867)The Gorman-Rupp Company reserves the right to discontinue any model or change specifications at any time without incurring any obligation.
©2012 American Machine and Tool Company. All rights reserved.
HVM-10
PUMPS ARE DESIGNED TOMOUNT HORIZONTALLY
OR VERTICALLY
** This dimension may vary due to the motor manufacturer’s specifications.(+) 3-Phase models can also operate on 50 Hz. (This will change full load amps, service factor and RPM.)NOTE: Dimensions are in inches (centimeters) and have a tolerance of ± 1/8”NOTE: Electric supply for all motors must be within ±10% of nameplate voltage rating (Ex. 230V ± 10%= 207 to 253)
XCI (-95) = Cast Iron Construction with Bronze ImpellerXB (-97) = Cast Bronze Construction with Bronze Impeller
Model ‡ HP PH ENCVoltage
@ 60 Hz +Full Load
Amps A B C D E F L** W H
B & GCast Iron
Equiv
B & GBronzeEquiv
‡ Ship Wt.(Lbs.)
58641/3
1TEFC
115/230 7/45.4 [13.7] 6.5 [16.5] 3.1 [7.8] 1.4 [3.5] 0.5 [1.3] 4.0 [10.2] 19.5 [49.5] 8.0 [20.3] 11.5 [29.2]
S607S B607S 80
5865 3 230/460 2/1 607T B607T 77
58621/2
1TEFC
115/230 9/55.4 [13.7] 6.5 [16.5] 3.1 [7.8] 1.4 [3.5] 0.5 [1.3] 4.0 [10.2] 19.5 [49.5] 8.0 [20.3] 11.5 [29.2]
608S B608S 84
5863 3 230/460 3/2 608T B608T 80
58603/4
1TEFC
115/230 12/65.4 [13.7] 6.5 [16.5] 3.1 [7.8] 1.4 [3.5] 0.5 [1.3] 4.0 [10.2] 19.5 [49.5] 8.0 [20.3] 11.5 [29.2]
609S B609S 90
5861 3 230/460 3/2 609T B609T 84
58743/4
1TEFC
115/230 12/65.4 [13.7] 7.0 [17.8] 3.6 [9.1] 1.0 [2.5] 0.7 [1.8] 4.6 [11.7] 20.0 [50.8] 8.6 [21.8] 13.5 [34.3]
621S B621S 87
5875 3 230/460 3/2 621T B621T 86
58721
1TEFC
115/230 14/75.4 [13.7] 7.0 [17.8] 3.6 [9.1] 1.0 [2.5] 0.7 [1.8] 4.6 [11.7] 20.0 [50.8] 8.6 [21.8] 13.5 [34.3]
613S B613S 92
5873 3 230/460 4/2 613T B613T 90
58701-1/2
1TEFC
115/230 17/95.4 [13.7] 7.0 [17.8] 3.6 [9.1] 1.0 [2.5] 0.7 [1.8] 4.6 [11.7] 20.0 [50.8] 8.6 [21.8] 13.5 [34.3]
614S B614S 102
5871 3 230/460 5/3 614T B614T 94
58863/4
1TEFC
115/230 12/65.5 [13.9] 7.0 [17.8] 3.4 [8.6] 1.0 [2.5] 0.7 [1.8] 5.0 [12.7] 19.9 [50.5] 9.3 [23.6] 13.5 [34.3]
622S B622S 89
5887 3 230/460 3/2 622T B622T 87
58841
1TEFC
115/230 14/75.5 [13.9] 7.0 [17.8] 3.4 [8.6] 1.0 [2.5] 0.7 [1.8] 5.0 [12.7] 19.9 [50.5] 9.3 [23.6] 13.5 [34.3]
623S B623S 94
5885 3 230/460 4/2 623T B623T 92
58821-1/2
1 115/230 17/95.5 [13.9] 7.0 [17.8] 3.4 [8.6] 1.0 [2.5] 0.7 [1.8] 5.0 [12.7] 19.9 [50.5] 9.3 [23.6] 13.5 [34.3]
617S B617S 104
5883 3 230/460 5/3 617T B617T 96
58802
1TEFC
115/230 22/115.5 [13.9] 7.0 [17.8] 3.4 [8.6] 1.0 [2.5] 0.7 [1.8] 5.0 [12.7] 19.9 [50.5] 9.3 [23.6] 13.5 [34.3]
618S B618S 105
5881 3 230/460 6/3 618T B618T 97
TEFC
Curve
A
B
C
D
E
F
G
H
I
J
G
4.0 [10.2]
4.0 [10.2]
4.0 [10.2]
4.0 [10.2]
4.0 [10.2]
4.0 [10.2]
4.3 [10.9]
4.3 [10.9]
4.3 [10.9]
4.3 [10.9]
Standard Features• Includes Mounting Flange Kit for 1-1/2" NPT; Includes (2)Flanges, (2) Gaskets and Fasteners
• Special Flange Designed to Accept B&G Flange or Standard150 Lb. 4 bolt Flanges
• 1/8" NPT Seal Wash/Vent Port
• EPDM/EPR Mechanical Seal and Casing O-Ring Standard
• Optional Viton® Mechanical Seals and O-Rings Available
• Stainless Steel (300 Series) Sleeve Protects Stub Shaft from Liquid
• Steel Shaft with Sealed Ball Bearing Design Permits Removalof Motor Without Disconnecting Pump or Loss of Liquid
• High Efficiency Closed Bronze Impeller
• Available in Either Single or Three Phase TEFC 56C Motorswith Standard NEMA Mounting Dimensions
• Maximum Working Pressure 150 PSI
®
A Gorman-Rupp CompanyInline 1-1/2˝ Circulator Pumps
1212
Pump Dimensional & Specification Data
When OrderingAdd the CorrectSuffix (-9x) Suffixto Model NumberIndicating MaterialSelection.