s: 5 metalcraft roofing01 wip01 bim© 2013 drawing setse ... · 5mm rivets @ 250crs. z profile (not...
TRANSCRIPT
RESIDENTIAL ROOFING
www.metalcraftgroup.co.nz
Architectural / Specification EnquiriesPh: 09 274 0408
Mobile: 027 603 1096Email: [email protected]
ThermoSpan EPS
RREPSMetalcraftInsulated Panel Systems
00 / 25 COVER SHEET01 / 25 ROOF RIDGE02 / 25 ROOF RIDGE 203 / 25 SAWTOOTH RIDGE04 / 25 SAWTOOTH EAVE05 / 25 SAW TOOTH SOFFIT DETAIL06 / 25 ROOF VALLEY07 / 25 BARGE WITH PROFILED CLADDING08 / 25 GUTTER DETAIL09 / 25 CANTILEVER BARGE CAPPING DETAIL10 / 25 PARAPET WITH TRANSVERSE APRON11 / 25 TRANSVERSE APRON12 / 25 PARALLEL APRON13 / 25 MAX. 85mm DIAMETER PIPE PENETRATION14 / 25 OVER 85mm DIAMETER PIPE PENETRATION15 / 25 RESIDENTIAL STEP DETAIL15A / 25 EXPANSION STEP DETAIL16 / 25 CHIMNEY PENETRATION DETAIL17 / 25 FASCIA AND BARGE FLASHING DIMENSIONS18 / 25 3D RIDGE TO BARGE JUCTION19 / 25 3D DUTCH GABLE20 / 25 3D APRON21 / 25 3D OVER 85mm DIAMETER PIPE PENETRATION22 / 25 3D CHIMNEY PENETRATION23 / 25 3D RIDGE/BARGE FLASHINGS24 / 25 3D DUTCH GABLE FLASHINGS25 / 25 PANEL PROFILE AND SIZE
DETAIL LIST
PRE-FINISHED RIDGE CAP0.55 FLASHING
STOPENDS TO ROOF CLADDING
PURLIN
METALCRAFTTHERMOSPAN ROOFING
14G TEK SCREW WITH NEOPRENEWASHER 40mm MIN. EMBEDMENTIN EACH RIB
PROFILED EDGE DRESSEDOVER THERMOSPAN RIBS
TIMBER FRAMEBY OTHERS
0.55mm COLORSTEELFLASHING
DIMENSION VARIES DEPENDINGON PANEL THICKNESSES
5mm RIVETS
FOAM INFILL
5mm POP RIVETS OR PREFINISHEDSELF TAPPING SCREW WITHNEOPRENE WASHER
PROFILED FILLERSEALED TOP & BOTTOM
XX
BUTYL TAPE(OPTIONAL)
3° m
in.
5mm
GAP
SITUATION 1
1. LOW, MEDIUM, HIGH WIND ZONES,WHERE ROOF PITCH ≥ 10°
MIN. 130mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
SITUATION 2
1. ALL ROOF PITCHES IN VERY HIGHWIND ZONE2. LOW, MEDIUM, HIGH WIND ZONESWHERE ROOF PITCH ≤ 10°
MIN. 200mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
X
SITUATION 3
1. FOR ALL ROOF PITCHES INEXTRA HIGH WIND ZONES
CATEGORY A
1. NORMAL EXPOSURE2. ROOF PITCH >10°
MIN. 130mm
CATEGORY B
1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.2. ROOF PITCH <10°
MIN. 200mmX
ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE
ACCEPTABLE SOLUTION AS PER E2/ASI
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
ROOF RIDGE
01 / 2530.08.2016
PRE-FINISHED RIDGE CAP0.55 FLASHING
STOPENDS TO ROOF CLADDING
METALCRAFTTHERMOSPAN ROOFING
14G TEK SCREW WITHNEOPRENE WASHER 40mm MIN.EMBEDMENT IN EACH RIB
PROFILED EDGE OVERTHERMOSPAN RIBS
TIMBER FRAME BY OTHERS
FOAM INFILL
5mm POP RIVET OR PRE-FINISHEDSELF-TAPPING TEK SCREW WITHNEOPRENE WASHER
PROFILED FILLER SEALEDTOP & BOTTOM
X X
3° m
in.
5mm
GAP
SITUATION 1
1. LOW, MEDIUM, HIGH WIND ZONES,WHERE ROOF PITCH ≥ 10°
MIN. 130mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
SITUATION 2
1. ALL ROOF PITCHES IN VERY HIGHWIND ZONE2. LOW, MEDIUM, HIGH WIND ZONESWHERE ROOF PITCH ≤ 10°
MIN. 200mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
X
SITUATION 3
1. FOR ALL ROOF PITCHES INEXTRA HIGH WIND ZONES
CATEGORY A
1. NORMAL EXPOSURE2. ROOF PITCH >10°
MIN. 130mm
CATEGORY B
1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.2. ROOF PITCH <10°
MIN. 200mmX
ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE
ACCEPTABLE SOLUTION AS PER E2/ASI
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
ROOF RIDGE 2
02 / 2530.08.2016
PROFILED EDGE OVERTHERMOSPAN RIBS
STOPENDS TO PANEL ROOFING
TIMBER FRAMING BY OTHERS
WEATHERBOARDS ON CAVITY
PERMEABLE WALL UNDERLAY,SHOWN DASHED
5mm POP RIVET OR PRE-FINISHEDSELF-TAPPING TEK SCREW WITHNEOPRENE WASHER
METALCRAFT THERMOSPANROOFING
PRE-FINISHED SAWTOOTHRIDGE CAP 0.55 FLASHING
14G TEK SCREW WITHNEOPRENE WASHER 40mmMIN. EMBEDMENT IN EACH RIB
PRE-FINISHED SAWTOOTHSOFFIT FLASHING
X
5mm
GAP
FOAM INFILL
PRE-FINISHED POP RIVET BEDDEDIN SILICONE OR PRE-FINISHED 8gWAFER-TEK SCREW
BUTYL TAPE (OPTIONAL)
3° m
in.
SITUATION 1
1. LOW, MEDIUM, HIGH WIND ZONES,WHERE ROOF PITCH ≥ 10°
MIN. 130mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
SITUATION 2
1. ALL ROOF PITCHES IN VERY HIGHWIND ZONE2. LOW, MEDIUM, HIGH WIND ZONESWHERE ROOF PITCH ≤ 10°
MIN. 200mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
X
SITUATION 3
1. FOR ALL ROOF PITCHES INEXTRA HIGH WIND ZONES
CATEGORY A
1. NORMAL EXPOSURE2. ROOF PITCH >10°
MIN. 130mm
CATEGORY B
1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.2. ROOF PITCH <10°
MIN. 200mmX
ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE
ACCEPTABLE SOLUTION AS PER E2/ASI
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
SAWTOOTH RIDGE
03 / 2530.08.2016
TIMBER/FIBRE CEMENTSOFFIT
METALCRAFT THERMOSPANROOFING
PRE-FINISHED SAWTOOTHRIDGE CAP FLASHING
STOPENDS TO ROOFCLADDING
PROFILED EDGE OVERTHERMOSPAN RIBS
5mm POP RIVET OR PRE-FINISHEDSELF-TAPPING TEK SCREW WITHNEOPRENE WASHER
X
5mm
GAP
BUTYL TAPE (OPTIONAL)
PRE-FINISHED SELFTAPPING TEK SCREWWITH NEOPRENE WASHER
3° m
in.
SITUATION 1
1. LOW, MEDIUM, HIGH WIND ZONES,WHERE ROOF PITCH ≥ 10°
MIN. 130mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
SITUATION 2
1. ALL ROOF PITCHES IN VERY HIGHWIND ZONE2. LOW, MEDIUM, HIGH WIND ZONESWHERE ROOF PITCH ≤ 10°
MIN. 200mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
X
SITUATION 3
1. FOR ALL ROOF PITCHES INEXTRA HIGH WIND ZONES
CATEGORY A
1. NORMAL EXPOSURE2. ROOF PITCH >10°
MIN. 130mm
CATEGORY B
1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.2. ROOF PITCH <10°
MIN. 200mmX
ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE
ACCEPTABLE SOLUTION AS PER E2/ASI
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
SAWTOOTH EAVE
04 / 2530.08.2016
METALCRAFT THERMOSPANROOFING
TIMBER FRAMING BY OTHERS
THERMOSPAN HEAD BARGE 0.55FLASHING
4.5mm SOFFIT BOARD
14G TEK SCREW WITHNEOPRENE WASHER 40mm MIN.EMBEDMENT IN EACH RIB
5mm POP RIVET OR PRE-FINISHEDSELF-TAPPING TEK SCREW WITHNEOPRENE WASHER
0.55 FLASHING OR 50x50 ANGLE
WEATHERBOARD
FOAM INFILL
STOPEND TO ROOF CLADDING
PERMEABLE WALL UNDERLAY,SHOWN DASHED
THERMAL CUT STEEL SKIN
X
5mm
GAP
BUTYL TAPE OPTIONAL
PRE-FINISHED SELF TAPPING TEKSCREW WITH NEOPRENEWASHER
3° min.
SITUATION 1
1. LOW, MEDIUM, HIGH WIND ZONES,WHERE ROOF PITCH ≥ 10°
MIN. 130mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
SITUATION 2
1. ALL ROOF PITCHES IN VERY HIGHWIND ZONE2. LOW, MEDIUM, HIGH WIND ZONESWHERE ROOF PITCH ≤ 10°
MIN. 200mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
X
SITUATION 3
1. FOR ALL ROOF PITCHES INEXTRA HIGH WIND ZONES
CATEGORY A
1. NORMAL EXPOSURE2. ROOF PITCH >10°
MIN. 130mm
CATEGORY B
1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.2. ROOF PITCH <10°
MIN. 200mmX
ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE
ACCEPTABLE SOLUTION AS PER E2/ASI
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
SAW TOOTH SOFFIT DETAIL
05 / 2530.08.2016
TIMBER BEAMSTRUCTURE BY OTHERS
PURLIN
METALCRAFT THERMOSPANROOFING
14G TEK SCREW WITHNEOPRENE WASHER 40mmMIN. EMBEDMENT IN EACH RIB
PREFINISHED 0.55 VALLEY GUTTER
80mm MIN
50m
m M
IN
MIN
. 20mm
80mm MIN
B: CLEARANCE BETWEEN ROOFING
250mm MIN
SITUATION 1
MAX. CATCHMENT 25m²MIN. ROOF PITCH 8°
MIN. 250mm
MIN. 50mm
MIN. 80mm
SITUATION 2
MAX. CATCHMENT 16m²MIN. ROOF PITCH 12.5°
160mm - 249mm
MIN. 40mm
MIN. 60mm
A
B
C
ACCEPTABLE SOLUTION AS PER E2/ASI
* ROOF PITCH FOR VALLEYS AS PER E2.
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems As indicated
ROOF VALLEY
06 / 2530.08.2016
PRE-FINISHED 0.55BARGE FLASHING
METALCRAFT THERMOSPANROOFING
WEATHERBOARDS ONCAVITY
PERMEABLE WALLUNDERLAY, SHOWN DASHED
TIMBER FRAMING BYOTHERS
14G TEK SCREW WITHNEOPRENE WASHER 40mmMIN. EMBEDMENT
Y
5mm RIVETS @ 250CRS.
Z PROFILE (NOT REQUIREDWHEN OVER 2 RIBS)
THERMAL CUT STEEL SKIN
Z
SITUATION 1
1. LOW, MEDIUM, HIGH WIND ZONES,WHERE ROOF PITCH ≥ 10°
AT LEAST TWO CRESTS
MIN. 50mm
SITUATION 2
1. VERY HIGH WIND ZONE2. LOW, MEDIUM & HIGH WINDZONES WHERE ROOF PITCH ≤ 10°AT LEAST TWO CRESTS
MIN. 70mm
Y
Z
SITUATION 3
1.ALL ROOF PITCHES IN EXTRAHIGH WIND ZONE
AT LEAST TWO CRESTS
MIN. 90mm
CATEGORY A
1. NORMAL EXPOSURE2. ROOF PITCH >10°
ONE RIB (TRAPEZOIDAL & TRAY)2 CORRUGATIONS
MIN. 50mm (VERTICALLY DOWN FACE - SMOOTH)MIN. 75mm (VERTICALLY DOWN FACE - PROFILED)
CATEGORY B
1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.2. ROOF PITCH <10°
ONE RIB, TWO RIBS (<20mm) (TRAPEZOIDAL & TRAY)3 CORRUGATIONS
MIN. 75mm (VERTICALLY DOWN FACE - SMOOTH)MIN. 100mm (VERTICALLY DOWN FACE - PROFILED)
Y
Z
ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE
ACCEPTABLE SOLUTION AS PER E2/ASI
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
BARGE WITH PROFILED CLADDING
07 / 2530.08.2016
WEATHERBOARD
125x125x75 BOX GUTTER
FIBRE CEMENT SOFFIT LINING
TIMBER FRAMING BYOTHERS
METALCRAFTTHERMOSPAN ROOING
TIMBER PACKER
PERMEABLE WALLUNDERLAY, SHOWN DASHED
THERMOSPAN FASCIAFLASHING
0.55 FLASHING OR 50x50ANGLE
5mm RIVETS @ 250CRS.
14G TEK SCREW WITHNEOPRENE WASHER 40mm MIN.EMBEDMENT IN EACH RIDGE
PRE-FINISHED SELF-TAPPINGTEK SCREW WITH NEOPRENEWASHER
3° m
in.
75mm MIN
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
GUTTER DETAIL
08 / 2530.08.2016
METALCRAFT THERMOSPAN ROOFING
PERMEABLE WALL UNDERLAY,SHOWN DASHED
14G TEK SCREW WITH NEOPRENEWASHER 40mm MIN. EMBEDMENT INEACH RIB
WEATHERBOARDS ON CAVITY
TIMBER FRAME BY OTHERS0.55 FLASHING OR 50x50 ANGLE
THERMOSPAN HEAD 0.55 BARGEFLASHING
THERMAL CUT STEEL SKIN
0.55 FLASHING OR 50x50 ANGLE14G SELF TAPPING TEK SCREW WITHNEOPRENE WASHER
0.55 Z PROFILE FLASHING (NOTREQUIRED WHEN SPANNING 2 RIBS)
X
BUTYL TAPE (OPTIONAL)
SITUATION 1
1. LOW, MEDIUM, HIGH WIND ZONES,WHERE ROOF PITCH ≥ 10°
MIN. 130mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
SITUATION 2
1. ALL ROOF PITCHES IN VERY HIGHWIND ZONE2. LOW, MEDIUM, HIGH WIND ZONESWHERE ROOF PITCH ≤ 10°
MIN. 200mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
X
SITUATION 3
1. FOR ALL ROOF PITCHES INEXTRA HIGH WIND ZONES
CATEGORY A
1. NORMAL EXPOSURE2. ROOF PITCH >10°
MIN. 130mm
CATEGORY B
1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.2. ROOF PITCH <10°
MIN. 200mmX
ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE
ACCEPTABLE SOLUTION AS PER E2/ASI
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
CANTILEVER BARGE CAPPING DETAIL
09 / 2530.08.2016
SELF TAPPING TEK SCREW WITH NEOPRENEWASHER
BARGE BOARD
WEATHERBOARDS ON CAVITY
PERMEABLE WALL UNDERLAY,SHOWN DASHED
PRE-FINISHED 0.55 PARAPET CAPFLASHING
TIMBER PACKER
PERMEABLE WALL UNDERLAY TOPROVIDE SEPARATION OF METALCAPPING AND TIMBER, SHOWN DASHED
FOAM FILLWALL FRAMING
ALUM. ANGLE ENGINEERED BY OTHERS
PRE-FINISHED APRON FLASHING
TIMBER NOG FOR FIXING APRON FLASHING
CONTINUOUS TIMBER PACKING
STST OR GALV. FLAT HEAD NAIL FOR FLASHING
PRE-FINISHED SELF TAPPING WAFER-TEK SCREW WITH NEOPRENE WASHER
STOPENDS TO ROOF CLADDING
5mm POP RIVET OR PRE-FINISHED SELF-TAPPING TEK SCREW WITH NEOPRENE WASHER
Z
NG
L
3° m
in.
SITUATION 1
1. LOW, MEDIUM, HIGH WIND ZONES,WHERE ROOF PITCH ≥ 10°
MIN. 35mm
MIN. 75mm
MIN. 130mm(EXCLUDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
MIN. 50mm
SITUATION 2
1. ALL ROOF PITCHES IN VERY HIGHWIND ZONE2. LOW, MEDIUM, & HIGH WINDZONES WHERE ROOF PITCH ≤ 10°
MIN. 35mm
MIN. 75mm
MIN. 200mm(EXCLUDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
MIN. 70mm
G
N
L
Z
SITUATION 3
1. ALL ROOF PITCHES IN EXTRAHIGH WIND ZONE
MIN. 35mm
MIN. 75mm
MIN. 200mm(EXCLUDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
MIN. 90mm
CATEGORY A
1. NORMAL EXPOSURE2. ROOF PITCH >10°
25mm
MIN. 50mm + HEM OR 75mm(VERTICALLY UP FACE - SMOOTH)MIN. 75mm + HEM OR 100mm(VERTICALLY UP FACE - PROFILED)
MIN. 150mm
MIN. 50mm (VERTICALLY DOWN FACE - SMOOTH)MIN. 75mm (VERTICALLY DOWN FACE - PROFILED)
CATEGORY B
1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.2. ROOF PITCH <10°
25mm
MIN. 75mm + HEM OR 100mm(VERTICALLY UP FACE - SMOOTH)MIN. 100mm + HEM OR 125mm(VERTICALLY UP FACE - PROFILED)
MIN. 200mm
MIN. 75mm (VERTICALLY DOWN FACE - SMOOTH)MIN. 100mm(VERTICALLY DOWN FACE - PROFILED)
G
N
L
Z
ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE
ACCEPTABLE SOLUTION AS PER E2/ASI
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
PARAPET WITH TRANSVERSE APRON
10 / 2530.08.2016
STOPENDS TO ROOF CLADDING
FOAM FILL
WALL FRAMING
PVC CAVITY CLOSER
WEATHERBOARDS ON CAVITY
NOG FOR FIXING APRON FLASHING
STST OR GALV. FLAT HEAD NAIL FORFLASHING
5mm POP RIVET OR PRE-FINISHED SELF-TAPPING TEK SCREW WITH NEOPRENEWASHER
METALCRAFT THERMOSPANROOFINGPRE-FINISHED 0.55 APRON FLASHING
PERMEABLE WALL UNDERLAY OVERFLASHING SHOWN DASHED
PERMEABLE WALL UNDERLAY,SHOWN DASHED
50x50x5mm ALUMINIUM ANGLEENGINEERED BY OTHERS
PREFINISHED SELF-TAPPING TEK SCREWSWITH NEOPRENE WASHER
FOAM FILL
3° m
in.
NG L
SITUATION 1
1. LOW, MEDIUM, HIGH WIND ZONES,WHERE ROOF PITCH ≥ 10°
MIN. 35mm
MIN. 75mm
MIN. 130mm(EXCLUDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
SITUATION 2
1. ALL ROOF PITCHES IN VERY HIGHWIND ZONES2. LOW, MEDIUM, AND HIGH WINDZONES WHERE ROOF PITCH ≤ 10°
MIN. 35mm
MIN. 75mm
MIN. 200mm(EXCLUDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
G
N
L
SITUATION 3
1. ALL ROOF PITCHES IN EXTRA HIGHWIND ZONE
MIN. 35mm
MIN. 200mm(EXCLUDING ANY SOFT EDGE OR TURN-DOWN TO ROOFING)
CATEGORY A
1. NORMAL EXPOSURE2. ROOF PITCH >10°
25mm
MIN. 50mm + HEM OR 75mm(VERTICALLY UP FACE - SMOOTH)MIN. 75mm + HEM OR 100mm(VERTICALLY UP FACE - PROFILED)
MIN. 150mm
CATEGORY B
1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.2. ROOF PITCH <10°
25mm
MIN. 75mm + HEM OR 100mm(VERTICALLY UP FACE - SMOOTH)MIN. 100mm + HEM OR 125mm(VERTICALLY UP FACE - PROFILED)
MIN. 200mm
G
N
L
ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE
ACCEPTABLE SOLUTION AS PER E2/ASI
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
TRANSVERSE APRON
11 / 2530.08.2016
PRE-FINISHED 0.55 APRONFLASHING
WEATHERBOARDS ON CAVITY
PERMEABLE WALL UNDERLAYOVER FLASHING, SHOWN DASHED
STST OR GALV. FLAT HEADNAIL FOR FIXING
NOG FOR FIXING APRONFLASHING
PVC CAVITY CLOSER
METALCRAFT THERMOSPANROOFING
5mm POP RIVET OR PRE-FINISHED SELF-TAPPING TEK SCREW WITH NEOPRENEWASHER
WALL FRAMING
PERMEABLE WALL UNDERLAY,SHOWN DASHED
FOAM FILL
50x50x5mm ALUMINIUM ANGLEENGINEERED BY OTHERS
GN
5mm
GAP
PRE-FILLED SELF-TAPPING TEKSCREW WITH NEOPRENE WASHER
M
SITUATION 1
1. LOW, MEDIUM, HIGH WIND ZONES,WHERE ROOF PITCH ≥ 10°
MIN. 35mm
MIN. 75mm
AT LEAST TWO CRESTS
SITUATION 2
1. ALL ROOF PITCHES INVERY HIGHWIND ZONE2. LOW, MEDIUM, AND HIGH WINDZONES WHERE ROOF PITCH ≤ 10°
MIN. 35mm
MIN. 75mm
AT LEAST TWO CRESTS
G
N
M
SITUATION 3
1. ALL ROOF PITCHES IN EXTRAHIGH WIND ZONE
MIN. 35mm
MIN. 75mm
AT LEAST TWO CRESTS
CATEGORY A
1. NORMAL EXPOSURE2. ROOF PITCH >10°
25mm
MIN. 50mm + HEM OR 75mm(VERTICALLY UP FACE - SMOOTH)MIN. 75mm + HEM OR 100mm(VERTICALLY UP FACE - PROFILED)
ONE RIB (TRAPEZOIDAL & TRAY)2 CORRUGATIONS (CORRUGATE)
CATEGORY B
1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.2. ROOF PITCH <10°
25mm
MIN. 75mm + HEM OR 100mm(VERTICALLY UP FACE - SMOOTH)MIN. 100mm + HEM OR 125mm(VERTICALLY UP FACE - PROFILED)
TWO RIBS (<20mm) (TRAPEZOIDAL & TRAY)3 CORRUGATIONS (CORRUGATE)
G
N
M
ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE
ACCEPTABLE SOLUTION AS PER E2/ASI
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
PARALLEL APRON
12 / 2530.08.2016
METALCRAFT THERMOSPAN ROOFING
PIPE (PIPEDIAMETER MIX.85mm)
EPDM FLEXIBLE CONE SLEEVE
MALLEABLE FLANGE, SCREW ORRIVET FIXED, AND SEALED TOPANEL PROFILE. FIT NEOPRENEWASHERS TO ALL SCREW FIXINGS.FITTED ON 45° ANGLE IN PLAN.REFER TO MRM CODE OF PRACTICEVERSION 2 2/2012.
TIMBER PURLIN
14G TEK SCREW WITH NEOPRENEWASHER 40mm MIN. EMBEDMENTIN EACH RIB
90mm FRAMING BY OTHERS
FOAM INFILL
0.55mm FLASHING
3° min.
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
MAX. 85mm DIAMETER PIPE PENETRATION
13 / 2530.08.2016
PRE-FINISHED SOAKERFLASHING UNDER PRE-FINISHEDROOF RIDGE CAP FLASHING
PIPE (PIPE DIAMETER OVER85mm AND MAX. 500mm)
EPDM FLEXIBLE CONE SLEEVE
METALCRAFT THERMOSPANROOFING
MALLEABLE FLANGE, SCREW ORRIVET FIXED, AND SEALED TO ROOFINGPROFILE. FIT NEOPRENE WASHERS TOALL SCREW FIXINGS. FITTED ON 45°ANGLE IN PLAN. REFER TO MRM CODEOF PRACTICE VERSION 2 2/2012. PRE-FINISHED SOAKER FLASHING
WITH PRE-FINISHED POP RIVETBEDDED IN SILICONE OR PRE-FINISHED 8g WAFER-TEK SCREW
METALCRAFT THERMOSPANROOFING
PRE-FINISHEDROOF RIDGECAP FLASHING
PRE-FINISHED SELF TAPPING TEK SCREWWITH NEOPRENE WASHER
EPDM FLEXIBLE CONE SLEEVE
TIMBER FRAMING BY OTHERS
X
M
FOAM INFILL
0.55mm FLASHING
PURLIN
L
5mm
GAP
REFER TO SHEET NO. 11/25 TRANSVERSE APRON
REFER TO SHEET NO. 12/25 PARALLEL APRON
REFER TO SHEET NO. 01/25 ROOF RIDGE
L
M
X
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
OVER 85mm DIAMETER PIPE PENETRATION
14 / 2530.08.2016
METALCRAFT THERMOSPAN ROOFING
14g TEK SCREW WITH NEOPRENE WASHERAT EACH RIB WITH 40mm MIN. EMBEDMENT
TIMBER FRAMING BY OTHERS
100
0.55mm BMT COLORSTEEL ANGLE
PRE-FINISHED 0.55BMTSTEPPED COLORSTEELFLASHING
PROFILLED FOAM CLOURESTRIP SEALED TOP &BOTTOM
5mm POP RIVET OR PRE-FINISHED SELF-TAPPINGTEK SCREW WITHNEOPRENE WASHER
3° m
in.
5mm
GAP
TURN UP PAN TO FULLRIB HEIGHT(SPECIAL TOOLAVAILABLE)
PACKER TO SUIT ROOFANGLE
X
SITUATION 1
1. LOW, MEDIUM, HIGH WIND ZONES,WHERE ROOF PITCH ≥ 10°
MIN. 130mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
SITUATION 2
1. ALL ROOF PITCHES IN VERY HIGHWIND ZONE2. LOW, MEDIUM, HIGH WIND ZONESWHERE ROOF PITCH ≤ 10°
MIN. 200mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
X
SITUATION 3
1. FOR ALL ROOF PITCHES INEXTRA HIGH WIND ZONES
CATEGORY A
1. NORMAL EXPOSURE2. ROOF PITCH >10°
MIN. 130mm
CATEGORY B
1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.2. ROOF PITCH <10°
MIN. 200mmX
ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE
ACCEPTABLE SOLUTION AS PER E2/ASI
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
RESIDENTIAL STEP DETAIL
15 / 2530.08.2016
FOAM INFILL
TURN DOWN PAN APRROX20° (SPECIAL TOOLAVAILABLE)
4mm Ø STEEL RIVET
0.55mm BMT COLORSTEELFLASHING
PRE-FINISHED SELF-TAPPING 14g TEK SCREWWITH NEOPRENE WASHERTO EVERY RIB (TYPICAL)
PROFILLED FOAM CLOURESTRIP SEALED TOP &BOTTOM
BUTYL TAPE
TURN UP PAN TO FULL RIBHEIGHT(SPECIAL TOOL AVAILABLE)
0.55mm BMT COLORSTEELFLASHING
50mm ROOF STEP
DETAIL RECOMMENDEDWHERE ROOF RUNSEXCEED 16m
3° min.
STEP
50mm
RO
OF
5mm
GAP
METALCRAFT THERMOSPANPANEL
300 min. LAPX
SITUATION 1
1. LOW, MEDIUM, HIGH WIND ZONES,WHERE ROOF PITCH ≥ 10°
MIN. 130mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
SITUATION 2
1. ALL ROOF PITCHES IN VERY HIGHWIND ZONE2. LOW, MEDIUM, HIGH WIND ZONESWHERE ROOF PITCH ≤ 10°
MIN. 200mm(EXCLUDDING ANY SOFT EDGE ORTURN-DOWN TO ROOFING)
X
SITUATION 3
1. FOR ALL ROOF PITCHES INEXTRA HIGH WIND ZONES
CATEGORY A
1. NORMAL EXPOSURE2. ROOF PITCH >10°
MIN. 130mm
CATEGORY B
1. EXPOSED (HIGHER RISK) & WIND LOAD EXCEEDS 1.5 kPa.2. ROOF PITCH <10°
MIN. 200mmX
ALTERNATIVE SOLUTION AS PER MRM CODE OF PRACTICE
ACCEPTABLE SOLUTION AS PER E2/ASI
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.
* - PLEASE REFER TO MRM CODE OF PRACTICE VERSION 2.2 /2012 AS MINIMUM PITCH WILL INCREASE DEPENDING ON SHEET LENGTH.
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
EXPANSION STEP DETAIL
15A / 2530.08.2016
100mm MIN
150m
m M
IN
CHIMNEY
PRE-FINSHEDSOAKER FLASHINGNOTCHED OVER RIBS
METALCRAFT THERMOSPANRESIDENTIAL ROOFINGTURN DOWN INTO GUTTER
MIN 150mm UPSTAND PRE-FINISHED1.6mm ALUMINIUM WELDEDSOAKER FLASHING
A MIN. OF 100mm CLEARANCE MUSTBE PROVIDED BETWEEN THESHEETING UPSIDE OF THEPENETRATION AND THE BACK CURBUPSTAND, TO PROVIDE FOR ANDTEMPORARY OBSTRUCTION ORABNORMAL RUNOFF. THE BACKCURB MUST BE SUFFICENT INDEPTH TO PROVIDE 150mm ROOFINGCOVER AND ROOFING FASTNERSMUST NOT PENETRATE THISFLASHING.
ROOF UNDERLAY WITH MIN.5mm LAP INTO BACK CURB
SIDE CURB AND BACKCURB 50mm HIGHER THANTHE CLADDING PROFILE
FLASHING SOFT EDGEDRESSED INTO PROFILE
PRIMARY FIXINGFASTENING TO THESTRUCTURE
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.
* - PLEASE REFER TO MRM CODE OF PRACTICE VERSION 2.2 /2012 AS MINIMUM PITCH WILL INCREASE DEPENDING ON SHEET LENGTH.
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 5
CHIMNEY PENETRATION DETAIL
16 / 2530.08.2016
METALCRAFTTHERMOSPAN EPSROOFING
GUTTER
FASCIA FLASHINGØ5mm STEEL RIVETS @300mm CRS
HEAD BARGE FLASHING
TURN UP WEATHERPROOF
150
40
30
VAR
AIES
DEP
END
ENT
ON
RO
OF
PITC
H
5010
TO SUIT ROOF PITCH (90° - ROOF PITCH)
TO SUIT ROOF PITCH (90° + ROOF PITCH)
20
20
30
VAR
IES
DEP
END
ENT
ON
RO
OF
PITC
H
TO SUIT ROOF PITCH(90° - ROOF PITCH)
TO SUIT ROOF PITCH(90° + ROOF PITCH)
THERMOSPAN HEAD BARGE FLASHING THERMOSPAN FASCIA FLASHING
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
- BUILDING PAPER IS THE COMMON GENERIC NAME FOR PERMEABLEROOF AND WALL UNDERLAYS. PLEASE REFER TO NZBC E2/AS1 ANDMRM CODE OF PRACTICE VERSION 2.2 /2012.
* - PLEASE REFER TO MRM CODE OF PRACTICE VERSION 2.2 /2012 AS MINIMUM PITCH WILL INCREASE DEPENDING ON SHEET LENGTH.
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems 1 : 2
FASCIA AND BARGE FLASHING DIMENSIONS
17 / 2530.08.2016
PRE-FINISHED RIDGE CAPFLASHING
METALCRAFT THERMOSPANTHERMOSPAN
PRE-FINISHED BARGE FLASHING
PURLIN
ROOF FRAMING
FASCIA BOARD
WALL CLADDING ON CAVITY
WALL FRAMING
* PLEASE REFER TO MRM CODEOF PRACTICE VERSION 2.2/2012AND RANZ HOW TO ON-SITEGUIDE METAL ROOF FLASHINGSFOR FURTHER INFORMATION ONFLASHING COVER WIDTHS.
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems
3D RIDGE TO BARGE JUCTION
18 / 2530.08.2016
PRE-FINISHED RIDGE FLASHING
METALCRAFT THERMOSPAN PANELSTURN DOWN INTO GUTTERREFER TO EAVE DETAILS FORMINIMUM ROOF OVERHANG
PRE-FINISHED BARGE FLASHING
PRE-FINISHED APRONFLASHING
PRE-FINISHED HIP FLASHING
GUTTER
FASCIA BOARD
* PLEASE REFER TO MRM CODE OFPRACTICE VERSION 2.2/2012 AND RANZHOW TO ON-SITE GUIDE METAL ROOFFLASHINGS FOR FURTHER INFORMATIONON FLASHING COVER WIDTHS.
WALL CLADDING ON CAVITY
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems
3D DUTCH GABLE
19 / 2530.08.2016
GUTTER
METALCRAFT THERMOSPANPANELSTURN DOWN INTO GUTTERREFER TO EAVE DETAILS FORMINIMUM ROOF OVERHANG
WALL CLADDING ON CAVITY
PRE-FINISHED APRON FLASHINGWITH HEMMED EDGE
PRE-FINISHED APRON DIVERTER
* PLEASE REFER TO MRM CODE OFPRACTICE VERSION 2.2/2012 ANDRANZ HOW TO ON-SITE GUIDE METALROOF FLASHINGS FOR FURTHERINFORMATION ON FLASHING COVERWIDTHS.
WALL CLADDING ON CAVITY
FASCIA BOARD
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems
3D APRON
20 / 2530.08.2016
PRE-FINISHED SOAKERFLASHING
EPDM FLEXIBLE CONE SLEEVE
MALLEABLE FLANGE, SCREWOR RIVET FIXED, AND SEALEDTO ROOFING PROFILE. FITNEOPRENE WASHERS TO ALLSCREW FIXINGS. FITTED ON45° ANGLE IN PLAN. REFER TOMRM CODE OF PRACTICEVERSION 2 2/2012.
PRE-FINISHED ROOF RIDGEFLASHING
PIPE(DIAMETER OVER 85mmDIAMETER)
METALCRAFT THERMOSPANPANELS
PRE-FINISHED ROOF BARGEFLASHING
PRE-FINISHED SOAKERFLASHING LINE UNDER PRE-FINISHED ROOF RIDGE FLASHING
* PLEASE REFER TO MRM CODE OFPRACTICE VERSION 2.2/2012 ANDRANZ HOW TO ON-SITE GUIDEMETAL ROOF FLASHINGS FORFURTHER INFORMATION ONFLASHING COVER WIDTHS.
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems
3D OVER 85mm DIAMETER PIPE PENETRATION
21 / 2530.08.2016
METALCRAFT THERMOSPANPANELS TURN DOWN INTOGUTTER
PRE-FINISHED APRONFLASHING
WALL CLADDING ON CAVITY
PREFINISHED VALLEY GUTTERPURLIN
PRE-FINISHED SOAKERFLASHING
VALLEY BOARD
ROOF FRAMING
MIN
. 110
mm
UPS
TAN
D
MIN. 110mm UPSTANDPRE-FINISHED 1.6mmALUMINIUM WELDEDSOAKER FLASHING
* PLEASE REFER TO MRM CODEOF PRACTICE VERSION 2.2/2012AND RANZ HOW TO ON-SITEGUIDE METAL ROOF FLASHINGSFOR FURTHER INFORMATION ONFLASHING COVER WIDTHS.
DIVERTER FLASHING ONUPPER SIDE OF CHIMNEY
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems
3D CHIMNEY PENETRATION
22 / 2530.08.2016
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems
3D RIDGE/BARGE FLASHINGS
23 / 2530.08.2016
OPTION 1
RIDGE CAPFLASHING
ADDITIONALSADDLEFLASHING
BARGEFLASHING
RIDGE CAPFLASHING
ADDITIONALSADDLEFLASHING
BARGEFLASHING
OPTION 2
* PLEASE REFER TO MRM CODEOF PRACTICE VERSION 2.2/2012AND RANZ HOW TO ON-SITEGUIDE METAL ROOF FLASHINGSFOR FURTHER INFORMATIONON FLASHING COVER WIDTHS.
(3) PRE-FINISHED 3DSADDLE FLASHING
(4) PRE-FINISHEDBARGE FLASHING
(2) PRE-FINISHEDAPRON FLASHING
(1) PRE-FINISHED HIP FLASHING
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems
3D DUTCH GABLE FLASHINGS
24 / 2530.08.2016
* PLEASE REFER TO MRM CODE OFPRACTICE VERSION 2.2/2012 AND RANZHOW TO ON-SITE GUIDE METAL ROOFFLASHINGS FOR FURTHERINFORMATION ON FLASHING COVERWIDTHS.
THERMOSPAN EPS
A = 50, 75, 100, 125,150, 200, 250
A
1000
SCALE @ 1:5
SCALE @ 1:2
FLAT FINISH
32
- PLEASE NOTE FOR RESIDENTIAL ROOFING A MINIMUM THICKNESS OF150mm IS RECOMMENDED - CONTACT METALCRAFT
INTERNAL LINER FINISHES
SILKLINE FINISH
MESA FINISH
RIBBED FINISH
15 30
589 40 9
12
12 4 107
1
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 2.2 /2012, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer.
RESIDENTIAL ROOFING
ScaleDate Sheet
ThermoSpan Residental
RRTSMetalcraftInsulated Panel Systems As indicated
PANEL PROFILE AND SIZE
25 / 2530.08.2016